Installation
N300 WiFi Range Extender
Model WN3100RP
Download from Www.Somanuals.com. All Manuals Search And Download.
Meet Your Extender
Before you install your extender, familiarize yourself with its LEDs,
buttons, and port.
Front and Right Side Panels
Router
Arrow
LED
Client
Arrow
LED
Client Link
LED
Router Link
LED
Power LED
WPS LED
Ethernet port
Pass-through
power socket
(varies by region)
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Rear and Leſt Side Panels
WPS
button
Product label
Factory Reset
button
Device On/Off
switch
Power connector
(varies by region)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
LED Descriptions
Router Link
LED
This LED indicates the connection between the extender and
the router or access point.
Solid green. Best connection.
Solid amber. Good connection.
Solid red. Poor connection.
Off. No connection.
Client Link LED This LED indicates the connection between the extender and
a computer or WiFi device.
Solid green. Best connection.
Solid amber. Good connection.
Solid red. Poor connection.
Off. No connection.
Power LED
WPS LED
Solid amber. The extender is booting.
Solid green. The extender is powered on.
Off. The extender is powered off.
Solid green. WiFi security is enabled (WPA or WPA2).
Blinking green. A WPS connection is in progress.
Off. WiFi security is not enabled.
Note: If the Router Arrow LED
or Client Arrow LED
extender is in a good location.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Install the WiFi Extender
Place the extender, apply power, and connect it to your WiFi network.
Place the Extender and Apply Power
1. Place your extender in the same room as your WiFi router.
Proximity to the WiFi router is required only during the initial setup
process.
2. Plug the extender into an electrical outlet.
The Power LED lights
green. If the Power LED does not light,
slide the Device On/Off switch on the side of the extender to the On
position.
Connect to an Existing WiFi Network
To extend the range of your WiFi network, you must connect the extender
to your existing WiFi network. You can do this in one of two ways:
•
•
Connect with web browser setup. For more information, see
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect with WPS
Wi-Fi Protected Setup (WPS) lets you join a secure WiFi network without
typing the network name and password.
Note: WPS does not support WEP network security. If you are using WEP
1. Press the WPS button on the side panel of the extender.
The WPS LED
blinks.
2. Within two minutes, press the WPS button on your router or access
point.
The WPS LED on the extender lights solid green, the Router Link LED
lights, and the extender connects to your existing WiFi network.
If the Router Link LED does not light, try again. If it still does not light,
3. Find the new extender network name on your computer or WiFi
device.
The extender’s wireless network name (SSID) changes to your existing
WiFi network name, with _EXT at the end of the name, for example:
•
•
Existing WiFi network name. MyNetworkName
New extended network name. MyNetworkName_EXT
7
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Connect your computer or WiFi devices to the new extended WiFi
network.
Use the same WiFi password that you use for your WiFi router.
5. Unplug the extender and move it to a new location closer to the area
with a poor WiFi signal.
The location that you choose must be within the range of your
existing WiFi router network.
6. Plug the extender into an electrical outlet.
The Power LED
lights green. If the Power LED does not light,
slide the Device On/Off switch on the side of the extender to the On
position.
7. Use the Router Link LED on the front panel to help you choose a spot
where the extender-to-router connection is optimal.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect with Web Browser Setup
1. Use a WiFi network manager on a computer or WiFi device to find and
connect to the NETGEAR_EXT (SSID) WiFi network.
Aſter the connection with the computer or WiFi device is established,
the Client Link LED
lights.
2. Open a web browser window from the same computer or WiFi device.
The browser takes you directly to the NETGEAR genie web browser
setup. If you are not automatically directed to NETGEAR genie, launch
Enter admin for the user name and password for the password.
The extender searches for WiFi networks in your area and displays a
list.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Select a WiFi network to extend and click the Continue button.
The following screen displays:
4. Type the network password (also called passphrase or security key) in
the Password field and click the Continue button.
The following screen displays:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
5. In the Name field, type the name (SSID) for your new extender WiFi
network and click the Continue button.
You can use the same security settings as the settings for your
existing network by selecting the check box.
The settings are applied and the following screen displays.
On iPads, iPhones, and MacBook computers, this screen automatically
closes.
6. Use a WiFi network manager on the computer or WiFi device to
connect to the extender’s newly created WiFi network.
Repeat this step for all of your computers and WiFi devices.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
7. If the screen is still displayed on your computer or WiFi device, select
the check box at the bottom of the screen and click the Continue
button.
A message displays confirming that the extender is connected to the
WiFi network.
8. Click the Finish button.
9. Unplug the extender and move it to a new location closer to the area
with a poor WiFi signal.
The location that you choose must be within the range of your
existing WiFi router network.
10. Plug the extender into an electrical outlet.
The Power LED
lights green. If the Power LED does not light,
slide the Device On/Off switch on the side of the extender to the On
position.
Use the Router Link LED
to help you choose a spot where the
extender-to-router connection is optimal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Find the Best Location
If the WiFi signal is weak, the first time you join the extender network, an
arrow LED blinks for two minutes. If this happens, adjust the position of
the extender.
•
If the Router Arrow LED
the router.
blinks, move the extender closer to
•
If the Client Arrow LED
blinks, move the computer or WiFi
device closer to the extender.
If no arrow LEDs are lit, the extender is in a good location.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connect an Ethernet-Enabled Device
Aſter the extender is connected to your existing WiFi network, you can
connect a wired device to the extender using an Ethernet cable. That
device can then access your existing network through the WiFi connection.
WiFi router
Extender
Blu-ray player
1. Set up the extender.
6.
2. Connect the extender to an existing WiFi network.
3. Plug the Ethernet cable from an Ethernet-enabled device in to the
Ethernet port on the extender.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Log In to Access Extender Settings
Aſter installation, you can log in to the extender to view or change the
extender’s settings.
1. Use a WiFi network manager on a computer or WiFi device to find and
connect to the new extended WiFi network.
Aſter the connection with the computer or WiFi device is established,
the Client Link LED
lights.
2. Launch a web browser.
A login screen displays.
4. Enter admin for the user name and password for the password.
NETGEAR genie displays.
5. Make any needed changes.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently Asked Questions
You can find more information about your product in the user manual,
The web browser setup guide keeps asking me for my network
password (passphrase) or security key, and I am sure that I entered
the correct password. What can I do?
The extender is probably placed at the borderline of the range covered by
the router or access point. For more information, see Place the Extender
If you are using WEP security, make sure that you are typing the network
password in the correct field.
My router security is WEP, and I entered the wrong passphrase
or security key on the extender. I cannot access the extender
anymore. What can I do?
The extender cannot check to see if the WEP passphrase is correct. If you
entered the wrong passphrase, your wireless device is not able to get the
IP address from the extender. You must reset the extender to its factory
default settings to get the IP address back.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
How do I restore the extender to its factory default settings?
1. Use a sharp object such as a pen or paper clip to press and hold the
Factory Reset button on the side of the extender for at least five
seconds until the Power LED blinks amber.
2. Release the Factory Reset button and wait for the extender to
reboot.
The extender resets and returns to the factory default settings.
You can now access the extender from your web browser using the
factory default settings.
Will the extender work if I connect it to the router with an Ethernet
cable?
No. The extender is designed to connect wirelessly to the router or access
point.
What are the user name and password to log in to the
extender?
The user name is admin, and the default password is password. Both are
case-sensitive.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
I enabled a wireless MAC filter, wireless access control, or access
control list (ACL) on my router. What should I do when installing
the extender?
When the WiFi device connects through the extender to your router,
the MAC address of the WiFi device shown on the router is translated to
another MAC address. If your router’s MAC filter, wireless access control,
or ACL is enabled, the WiFi device connects to the extender but cannot
get an IP address from the extender and cannot access the Internet.
To allow the WiFi device to receive an IP address from the extender and
access the Internet, you must provide the translated MAC address to the
router.
1. Log in to your router and disable the MAC filter, wireless access
control, or ACL.
For more information about how to disable your router’s MAC filter,
wireless access control, or ACL, see your router’s documentation.
2. Power on the extender and connect all of your WiFi devices to the
extender network.
3. Make sure that the Router Link LED remains lit.
4. Log in to your extender:
a. Launch a web browser.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
A login screen displays.
c. Enter admin for the user name and password for the password.
5. Select Maintenance > Attached Devices.
The Attached Devices screen displays the MAC addresses and virtual
MAC addresses for computers and WiFi devices that are connected to
the extender network.
6. On the router, add all of the virtual MAC addresses from your
extender to your router’s MAC filter table.
7. Enable the router’s MAC filter, wireless access control, or ACL.
I am connected to NETGEAR_EXT and launched a browser. Why
can’t I see the web browser setup guide?
Try these troubleshooting steps:
•
•
Make sure that your computer is set up to use DHCP (most are).
Make sure that the Client Link LED is green and that you are using a
valid IP address.
•
address field. Enter admin for the user name and password for the
password.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Support
Thank you for purchasing this NETGEAR product. After installing your device, locate the serial
number on the label of your product and use it to register your product at
https://my.netgear.com. You must register your product before you can use NETGEAR
telephone support. NETGEAR recommends registering your product through the NETGEAR
website.
For product updates and web support, visit http://support.netgear.com.
NETGEAR recommends that you use only the official NETGEAR support resources. You can
product’s user interface.
Trademarks
NETGEAR, the NETGEAR logo, and Connect with Innovation are trademarks and/or registered
trademarks of NETGEAR, Inc. and/or its subsidiaries in the United States and/or other
countries. Information is subject to change without notice. © NETGEAR, Inc. All rights
reserved.
Compliance
For the current EU Declaration of Conformity, visit
For regulatory compliance information, visit
See the regulatory compliance document before connecting the power supply.
NETGEAR, Inc.
350 East Plumeria Drive
San Jose, CA 95134, USA
September 2014
Download from Www.Somanuals.com. All Manuals Search And Download.
|