OWNER'S MANUAL
51CM CORDLESS REMOTE LCD TV/MONITOR
MODEL: TFTV515Y
N111
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
WARNING: TO REDUCE THE RISK OF OR ELECTRIC SHOCK, DO NOT EXPOSE THIS
APPARATUS TO RAIN OR MOISTURE.
The lightning flash with arrowhead symbol, within
an equilateral triangle is intended to alert the user
to the presence of insinuated dangerous voltage
within the product's enclosure that may be of
sufficient magnitude to constitute a risk of electric
shock to persons.
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of ,important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40
of the National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable
ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
(America only)
This product utilises tin-lead solder, and fluorescent lamp containing a small amount of mercury. Disposal of these
materials may be regulated due to environmental considerations. For disposal or recycling information, please contact
FCC STATEMENT (America only)
FCC Notice
LCD TV: A CLASS B digital device
This equipment has been tested and found to comply with the limits for a Class digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation
of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
FCC CAUTION:
Pursuant to 47CFR, Part 15.21 of the FCC rules, any changes or modifications to this monitor not
expressly approved by the manufacturer could cause harmful interference and would void the user's
authority to operate this device.
WARNING: This is a CLASS B product. In a domestic environment this product may cause
radio interference in which case the user may be required to take adequate
measures to counter interference.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions
Electrical energy can perform many useful functions, but it can also cause personal injuries and property damage if improperly
handled. This product has been engineered and manufactured with the highest priority on safety. But IMPROPER USE CAN
RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARD. In order to prevent potential danger, please observe
the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service
life of your PDP TV product, please read the following precautions carefully before using the product.
1. Read these instructions---All operating instructions must be read and understood before the product is operated.
2. Keep these instructions---These safety and operating instructions must be kept in a safe place for future reference.
3. Heed all warnings---All warnings on the product and in the instructions must be observed closely.
4. Follow all instructions---All operating instructions must be followed.
5. Do not use this apparatus near water---for example, near a bathtub,
washbowl, kitchen sink, or laundry tub, in a wet basement, or near swimming
pool, and the like.
Do not use immediately after moving from a low temperature to high
temperature environment, as this causes condensation, which may result in
fire, electric shock, or other hazards.
6. Clean only with dry cloth---Unplug this product from the wall outlet
before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a
damp cloth for cleaning.
7. Ventilation---Do not block any ventilation openings. Install in accordance
with the manufacturer instructions. The vents and other openings in the cabinet
are designed for ventilation. Do not cover or block these vents and openings
since insufficient ventilation can cause overheating and/or shorten the life of
the product. Do not place the product on a bed, sofa, rug or other similar
surface, since they can block ventilation openings. This product is not designed
for built-in installation; do not place the product in an enclosed place such as a
bookcase or rack, unless proper ventilation is provided or the manufacturer's
instructions are followed.
8. Heat sources---Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including amplifiers) that
produce heat.
9. Grounding or Polarisation---Do not defeat the safety purpose of the polarised or grounding-type plug. A polarised
plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet. (America only)
10. Power cord protection---Protect the power cord from being walked on or pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
11. Attachments---Only use attachments/ accessories specified by the manufacturer. Do not use attachments not
recommended by the manufacturer. Use of improper attachments can result in accidents.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions (continued)
12. Stand---Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. Do not place the product on an unstable
trolley, stand, tripod or table. Placing the product on an unstable base can cause the
product to fall, resulting in serious personal injuries as well as damage to the product.
When mounting the product on a wall, be sure to follow the manufacturer's instructions.
Use only the mounting by the hardware recommended manufacturer.
13. Carefully move---When a cart is used, use caution when moving the cart/apparatus
combination to avoid injury from tip-over. Sudden stops, excessive force and uneven
floor surfaces can cause the product to fall from the trolley.
14. Lightning---Unplug this apparatus during lightning storms or when unused for long
of periods time.
For added protection for this television equipment during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna. This will prevent damage to the equipment due to lightning and
power-line surges.
15. Servicing---Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
16. Replacement parts---In case the product needs replacement parts, make sure that the service person uses
replacement parts specified by the manufacturer, or those with the same characteristics and performance as the
shock and/or original parts. Use of unauthorised parts can result in fire, electric other danger.
17. Overloading---Do not overload wall outlets, extension cords, or convenience receptacles on other
equipment as this can result in a risk of fire or electric shock.
18. Entering of objects and liquids---Never insert an object into the product through vents or openings. High voltage
flows and/or in the product, and inserting an object can cause electric shock short internal parts. For the same reason,
do not spill water or liquid on the product.
19. Damage, requiring service---If any of the following conditions occurs unplug the power cord from the AC outlet, and
repairs. request a qualified service person to perform
a. When the power cord or plug is damaged.
b. When a liquid is spilled on the product or when objects have fallen into the product.
c. When the product has been exposed to rain or water.
d. When the product does not operate properly as described in the operating instructions.
Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls not
described in the instructions can cause damage, which often requires extensive adjustment work by a qualified technician.
e. If the product has been dropped or the cabinet has been damaged in any way.
f. When the product displays an abnormal condition or exhibits a distinct change in performance. Any noticeable
abnormality in the product indicates that the product needs servicing.
20. Safety checks---Upon completion of service or repair work, request the service technician to perform safety
checks to ensure that the product is in proper operating condition.
21. Wall or ceiling mounting---When mounting the product on a wall or ceiling, be sure to install the product according
to the method recommended by the manufacturer. This is a safety feature.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Safety Precautions (continued)
22. Power source---This product is intended to be supplied by a listed power supply indicated on the marking label. If you
are not sure of the type of power supply to your home, consult your product dealer or local power company. For added
protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it
from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power line
surges. When the unit has to be used with another power supply voltage, the power cable must be changed. Consult your
product dealer. The socket outlet should be installed near the equipment and easily accessible. Use only the power cord
designated by our dealer to ensure safety and EMC. When connecting other products such as VCRs and personal computers,
you should turn off the power of the unit for protection against electric shock.
23. Panel protection---The LCD panel used in this product is made of glass.
Therefore, it can break when the product is dropped or impacted upon by other
objects. Be careful not to be injured by broken glass pieces in case the LCD panel breaks.
24. Pixel defect---The LCD panel is a very high technology product, giving you finely detailed pictures. Occasionally,
a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this does not
affect the performance of your product.
If an outside antenna is connected to the television equipment, be sure the antenna system is grounded so as to
provide some protection against voltage surges and built-up static charges. Section 810 of the National Electrical
Code provides information with respect to proper grounding of the mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit,
connection to grounding electrodes, and requirements for the grounding electrode. (America only)
EXAMPLE OF ANTENNA GROUNDING AS PER
NATIONAL ELECTRICAL CODE
ANTENNA
LEAD IN WIRE
ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-21)
ELECTRIC
SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC---NATIONAL ELECTRICAL CODE
An outside antenna system should not be located in the vicinity of overhead
power lines or other electric light or power circuits, or where it can collide with
such power lines or circuits. When installing an outside antenna system, extreme
care should be taken to keep from touching such power lines or circuits, as
contact with them might be fatal.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
+
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparations (continued)
Antenna Connection
INSTALL the unit in a room where direct light will not fall upon the screen. Total darkness or a reflection on the
picture screen may cause eyestrain. Soft and indirect lighting is recommended for comfortable viewing.
Optimum reception of colour requires a good signal and will generally mean that an outdoor aerial must be used.
The exact type and position of the aerial will depend upon your particular area.
Note:
It is recommended that the 75-ohm coaxial cable be used to eliminate interference and noise which may occur due
to radio wave conditions.
The aerial cable should not be bundled with the power cord and the like.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Main Unit
CH-
CH+
VOL-
VOL+
SOURCE
MENU
1
2
3
5
4
1. SOURCE
To select the input signal source.
2. MENU
Press this button to access the MENU main page.
3. CH+/-
Press these two buttons to directly change the TV channel;
In OSD MENU, press these buttons to choose the OSD items.
4. VOL+/-
Press the VOL+ or VOL- button to directly increase or decrease the sound volume level;
In OSD MENU, press these buttons to adjust the value or setting of each item.
5. POWER
Press this button to turn the unit ON from STANDBY mode. Press it again to turn the set back to STANDBY
Note:
Functions of VOL+/-, CH+/-, MENU, SOURCE and POWER
are also provided to the remote control. This
operation manual provides a description based on operating functions with the remote control.
Download from Www.Somanuals.com. All Manuals Search And Download.
Identification of Controls (continued)
Main Unit
1
2
3
4
5
6
1. POWER SWITCH.
2. AV inputs
Receive video/audio signals from external sources such as VCR or DVD player.
3. S-Video input
Receive a S-Video signal from external source such as VCR or DVD player.
4. Antenna input
Allows you to connect cable or outdoor antenna.
5. D-Sub input /Audio Line in
Connectto the D-Sub/audio output jacks on your PC.
6. Component inputs
Connect to the audio and component output jacks of a DVD player or Set-Top Box.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control
+
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
Cautions before connecting
Carefully check the terminals for position and type before making any connections.
The illustration of the external equipment may be different depending on your model.
Loose connectors can result in image or colour problems. Make sure that all connectors are securely inserted
into their terminals.
Refer to the operating manual of the external device as well.
When connecting an external device, turn the power off on the panel to avoid any issues.
Connect a VCR
Yellow (VIDEO)
White (AUDIO L)
Red (AUDIO R)
S-Video
cable
Video
cable
Audio
cable
VCR
How to connect:
Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and VCR.
Note:
For better video, you can use the S-video jack source supports it.
The unit automatically identifies S-Video if you are using S-Video jack. We recommend you to disconnect S-Video
cable before you use Video jack.
Input Source
To play VCR
1. Turn on your LCD TV, press SOURCE
Video
button repeatedly to select Video.
Source Switch
2. Turn on your VCR, insert a videotape and press the Play button.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Connect a Camcorder
Yellow (VIDEO)
White (AUDIO L)
Red (AUDIO R)
Video Audio
cable cable
How to connect:
Connect the Audio/Video cables between the Audio (L/R)/Video jacks on the unit and camcorder.
To playback Camcorder
1. Turn on your LCD TV, press SOURCE
button repeatedly to select Video.
2. Turn on your camcorder and set it to output mode. (For details, refer to your camcorder owner's manual.)
3. Insert the tape into the camcorder and press Play button.
Input Source
Note:
Video
The operations of the camcorder may be different and is dependent on your model.
Please read the owner's manual of your camcorder to confirm operation.
Source Switch
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Connect a DVD player
White (AUDIO L)
Red (AUDIO R, Pr/Cr)
Green
Blue (Pb/Cb)
DTV RECEIVER
How to connect a DVD Player using Component Video Connections:
Connect the Video cable between the Y, Pb, Pr input jacks on the unit and Y, Pb, Pr (or Y, Cb, Cr) output jacks
on the DVD player.
Connect the Audio cable between the AUDIO input jack on the unit and AUDIO output jacks on the DVD player.
To play DVD
1. Turn on your LCD TV, press SOURCE
2. Turn on your DVD player.
button repeatedly to select YPbPr.
Input Source
YPbPr
3. Insert a disc and press PLAY button.
Source Switch
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections (continued)
Connect a PC
D-Sub
cable
Audio
cable
How to connect:
Connect a D-Sub cable between the D-Sub jack on the PC and the D-Sub input jack on the unit.
Connect an Audio cable between the AUDIO output on the PC and AUDIO input jack on the unit.
To Watch the PC screen
1. Turn on your LCD TV, press SOURCE
button repeatedly to select D-Sub.
Input Source
D-Sub
2. Turn on your PC and check for PC system requirements.
3. Adjust the screen resolution and settings on your computer to the preferred settings.
Source Switch
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Picture
Picture Mode
Brightness
Contrast
Color
Normal
50
75
60
50
12
Tint
Sharpness
Move
Select
Menu to exit
+
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorising the Channels
Your LCD TV can memorise and store all the available channels for both antenna and cable channels. After the
available channels are memorised, use CH+/- to scan the channels.
Storing Channels in Memory Automatically
Channel
Press MENU to display the menu main page.
Auto Search
1
Manual Search
Off
Skip
Press CH+/- repeatedly to select Channel page.
Fine Tune
AFC
2
3
4
5
On
B/G
Auto
Sound Mode
Color Mode
Channel Edit
Frequency
55.25
Press ENTER or VOL+/- to access the submenu.
Move
Select
Menu to exit
The Auto Search item will be highlighted automatically.
Press ENTER or VOL+/- to store channels in memory automatically.
The unit will begin memorising all the available channels. During the process of the Auto Search, you can press
Menu to exit.
Note:
Before you start Auto Search, please refer to the part of [Setting Color and Sound System] to select a proper
sound system according to your area.
Manual Search
Use Manual Search if desired channels cannot be memorised or if you would like to store channels to specific
channel numbers one by one.
Channel
Repeat steps 1~3 in [Storing Channels in Memory Automatically] to access the
Channel menu page.
Auto Search
Manual Search
Skip
1
Off
Fine Tune
AFC
On
Press CH+/- repeatedly to select Manual Search item.
2
3
Sound Mode
Color Mode
Channel Edit
B/G
Auto
Frequency
55.25
Press VOL+/- to start manual search.
Pressing VOL+, the set searches towards higher frequency;
Pressing VOL-, the set searches towards lower frequency;
Move
Select
Menu to exit
The search stops when a program is found and this program will be stored in current channel.
Manual Fine Tuning
Channel
Repeat steps 1~3 in [Storing Channels in Memory Automatically] to access the
Channel menu page.
Auto Search
Manual Search
Skip
1
Off
Fine Tune
AFC
On
Press CH+/- repeatedly to select Fine Tune item.
2
B/G
Auto
Sound Mode
Color Mode
Channel Edit
Frequency
55.25
Press VOL+/- to fine tune till the best possible picture and sound are obtained.
3
Move
Select
Menu to exit
If you fine tune a program manually, the AFC will be turned off automatically.
Setting Auto Frequency Control (AFC)
Channel
Repeat steps 1~3 in [Storing Channels in Memory Automatically] to access the
Channel menu page.
Auto Search
Manual Search
Skip
1
Off
Fine Tune
AFC
On
Press CH+/- repeatedly to select AFC item.
2
B/G
Auto
Sound Mode
Color Mode
Channel Edit
Frequency
55.25
Press ENTER or VOL+/- to select On or Off.
When the AFC is set to On, the unit will automatically tune the program frequency
to provide the best possible picture and sound.
3
Move
Select
Menu to exit
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Memorising the Channels (continued)
Adding and Erasing Channels
Channel
Auto Search
Use number buttons to directly select a channel that will be added or erased.
1
2
Manual Search
Skip
Off
Fine Tune
AFC
Repeat steps 1~3 in [Storing Channels in Memory Automatically] to access the
Channel menu page.
On
B/G
Auto
Sound Mode
Color Mode
Channel Edit
Frequency
55.25
Press CH+/- repeatedly to select Skip item.
3
4
Move
Select
Menu to exit
Press ENTER or VOL+/- to select On or Off.
When the item is set to on, the selected channel will be erased.
When the item is set to off, the selected channel will be added.
The erased channels can not be selected by using the CH+/- buttons unless you use number buttons to input
channel number directly.
Setting Colour and Sound System
Channel
Auto Search
Manual Search
Skip
Repeat steps 1~3 in [Storing Channels in Memory Automatically] to access the
Channel menu page.
1
Off
Fine Tune
AFC
On
Press CH+/- repeatedly to select Sound Mode or Color Mode item.
B/G
Auto
Sound Mode
Color Mode
Channel Edit
2
Frequency
55.25
Press VOL+/- to select a proper colour system and sound system according to your
area's broadcasting system.
3
Move
Select
Menu to exit
Editing Channels
The channel editing function is for you to arrange channel order as you wish.
Channel
Auto Search
Manual Search
Skip
Repeat steps 1~3 in [Storing Channels in Memory Automatically] to access the
Channel menu page.
1
Off
Fine Tune
AFC
On
B/G
Auto
Sound Mode
Color Mode
Channel Edit
Press CH+/- repeatedly to select Channel Edit item.
2
Frequency
55.25
Press VOL+/- to access the submenu.
Move
Select
Menu to exit
3
Press CH+/- repeatedly to select Current Channel or Object Channel item.
4
Using number buttons to input channel number.
Current Channel 008
Object Channel 018
Change
5
6
Press CH+/- repeatedly to select Change item.
Press Enter to exchange the contents between current channel and object channel.
7
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operations
Changing Channels
Using the Channel Buttons (CH+ or CH-)
Press the CH+ or CH- to change channels.
When you press the CH+ or CH-, the unit changes channels in sequence. You will see all the channels that the
unit has memorised.
You will not see channels that were erased.
Direct Accessing Channels
Press the number buttons to go directly to a channel.
To select a one-digit channel: press the 0-9 number buttons to input the channel number and press ENTER or wait for
some seconds to go to the selected channel.
To select a two-digit channel: press the 0-9 number buttons to input the channel number and press ENTER or wait for
some seconds to go to the selected channel.
To select a three-digit channel: press the 0-9 number buttons to input the channel number one by one, then the unit
goes to the selected channel.
Note:
When you use the number buttons, you can directly select channels that were erased.
Using the Return
button
Press this button to switch between the current channel and the previous channel.
Adjusting the Volume
Using the volume buttons (VOL+ and VOL-)
Press the VOL+ or VOL- to increase or decrease the volume.
Using the MUTE button
At any time, you can temporarily cut off the sound using the MUTE button.
Press the MUTE button and the sound cuts off.
1
To turn mute off, press the MUTE button again.
2
Selecting a MENU Language
Display
English
Press MENU to display the menu main page.
Language
Transparency
Back Light
Factory Reset
DCDi
1
2
Bright
Yes
On
Press CH+/- repeatedly to select Display page.
Press ENTER or VOL+/- to access the submenu.
The Language item will be highlighted automatically.
3
Move
Select
Menu to exit
Press ENTER or VOL+/- to select a proper menu language.
4
Press Menu to exit.
5
Note:
In some models, there may be only one menu language available. In this case, the menu language not be
adjusted by the user.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Picture
Using the Preset Picture Mode
Picture
Press MENU to display the menu main page.
The picture page will be displayed automatically.
Picture Mode
Brightness
Contrast
Color
Normal
1
50
75
60
50
12
Tint
Press ENTER or VOL+/- to access the Picture submenu.
The Picture Mode item is highlighted automatically.
2
Sharpness
Move
Select
Menu to exit
Press ENTER or VOL+/- to select a desired picture mode.
You may also use the P.MODE button to quickly select picture mode.
3
There are three preset picture modes (Bright, Soft and Normal) and one user-set picture mode (User). Each
preset mode has its own picture settings.
Bright: Select for a bright picture.
Soft: Select for a finely detailed picture.
Normal: Select for a normal picture.
Adjusted settings are stored in User mode.
Customising the Picture
Picture
Picture Mode
Brightness
Contrast
Color
User
Press MENU to display the menu main page.
1
50
75
60
50
12
The picture page will be displayed automatically.
Tint
Press ENTER or VOL+/- to access the Picture submenu.
Press CH+/- to select the item you wish to change.
Press VOL+/- to adjust the value of the item.
Press Menu to exit.
2
3
4
5
Sharpness
Move
Select
Menu to exit
In TV/Video mode
Option
Operation
Function
Brightness
Adjusts screen brightness for easier viewing of
dark picture such as night scenes and black
hair.
VOL+ lighter
VOL- darker
VOL+ stronger
VOL- weaker
Adjusts image contrast.
Adjusts colour saturation.
Adjusts tint for image.
Contrast
Color
VOL+ deeper
VOL- paler
VOL+ greenish
VOL- purplish
Tint*
Sharpness
Adjusts image sharpness and displays a
sharp image.
VOL+ sharper
VOL- softer
* The Tint is for NTSC only.
In D-Sub mode
Function
Operation
Option
Brightness
VOL+ lighter
VOL- darker
Adjusts screen brightness for easier viewing of
dark picture such as night scenes and black
hair.
VOL+ stronger
VOL- weaker
Adjusts image contrast.
Contrast
Color
Adjusts colour saturation.
VOL+ deeper
VOL- paler
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Adjusting Image in D-Sub mode
With working in D-Sub mode, this unit allows you to perform several adjustments for image
Adjusting the Picture Automatically
Image
Auto Adjustment
Image Position
Phase
Press MENU to display the menu main page.
1
2
30
1328
Clock
Press CH+/- repeatedly to select Image page.
Press ENTER or VOL+/- to access the Image page.
The Auto Adjustment item will be highlighted automatically.
3
Move
Select
Menu to exit
Auto Adjustment
Yes
Press ENTER or VOL+/- again to access the Auto Adjustment page.
The Auto Adjustment / Yes item will be highlighted automatically.
4
Auto Adjustment
Press ENTER or VOL+/- again to start Auto Adjustment.
The unit automatically adjusts phase, clock or position, etc.
5
Note:
Move
Select
Menu to exit
You may use the ADJUST button to quickly perform the Auto Adjustment.
Adjusting Clock and Phase
Image
Repeat steps 1-3 in [Adjusting the Picture Automatically] to access Image page.
Auto Adjustment
Image Position
Phase
1
30
1328
Clock
Press CH+/- repeatedly to select Clock or Phase item.
2
Press VOL+/- to adjust the value of the item until the screen is well-aligned.
3
Move
Select
Menu to exit
Adjust the clock frequency of the set's internal clock signal. If shimmering or rainbow-like noise is apparent in
the image, try adjusting the clock frequency setting.
You may find that images blur, depending on the clock phase of your PC's Processor. If you experience
blurring, you can obtain a clearer image by adjusting the phase setting.
Adjusting the Image Position
The unit allows you to adjust the image position of the screen if it is not well-aligned.
Image Position
Repeat steps 1~3 in [Adjusting the Picture Automatically] to access Image page.
1
0
Press CH+/- to select Image Position item.
2
0
Press ENTER or VOL+/- to access the Image Position page.
3
Move
Select
Menu to exit
Press CH+/- or VOL+/- to adjust the image position until the screen is well-aligned.
4
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting Sound
Customising the Sound
Audio
Press MENU to display the menu main page.
1
Bass
14
16
43
Treble
Balance
Press CH+/- repeatedly to select Audio page.
2
Press ENTER or VOL+/- to access the submenu.
3
Move
Select
Menu to exit
Press CH+/- to select Bass, Treble or Balance item.
4
Press VOL+/- to adjust the value of the item.
5
Function
Option
Operation
VOL+ stronger
Adjust Bass (low sounds).
Bass
VOL- weaker
VOL+ stronger
VOL- weaker
Treble
Adjust Treble (high sounds).
VOL+ Higher volume from right speaker.
VOL- Higher volume from left speaker.
Balance
Adjust volume balance (left and right
volumes).
Using the Preset Sound Mode
Use the S.MODE button to quickly select Sound mode.
There are three preset Sound modes (News, Movie and Music) and one user-set Sound mode (User). Each preset
mode has its own audio settings.
Movie: Select for a movie program.
Music: Select for a music program.
News: Select for a speech or conversation program.
Adjusted settings are stored in User mode.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Other Functions
Adjusting Menu Transparency
Display
English
Press MENU to display the menu main page.
Language
Transparency
Back Light
Factory Reset
DCDi
1
2
Bright
Press CH+/- repeatedly to select Display page.
Yes
On
Press ENTER or VOL+/- to access the submenu.
3
Move
Select
Menu to exit
Press CH+/- to select Transparency item.
4
5
Press VOL+/- to adjust transparency.
Note:
You may use the TRANSPARENCY button to quickly adjust the menu transparency.
Adjusting Back Light
Display
English
Repeat steps 1~3 in [Adjusting Menu Transparency] to access Display page.
1
2
Language
Transparency
Back Light
Factory Reset
DCDi
Bright
Press CH+/- repeatedly to select Back Light item.
Yes
On
Press ENTER or VOL+/- to adjust panel back light.
Note:
3
Move
Select
Menu to exit
You may use the BACKLIGHT function to quickly adjust the panel backlight.
Setting DCDi Function
Display
English
Language
Transparency
Back Light
Factory Reset
DCDi
Repeat steps 1~3 in [Adjusting Menu Transparency] to access Display page.
1
2
Bright
Yes
On
Press CH+/- repeatedly to select DCDi item.
Press ENTER or VOL+/- to select On or Off.
3
Move
Select
Menu to exit
You may set this function to On when viewing motion picture, which helps to
enhance picture quality by reducing sawtooth in the motion picture.
Loading Default Values
You may quickly load default values by using the Factory Reset item.
Caution: please be careful to use Factory Reset item. Once you confirm to use this function all your
settings will be reset and the unit loads default values.
Display
Repeat steps 1~3 in [Adjusting Menu Transparency] to access Display page.
1
2
3
Language
Transparency
Back Light
Factory Reset
DCDi
English
Bright
Press CH+/- repeatedly to select Factory Reset item.
Yes
On
Press ENTER or VOL+/- to load default values.
Move
Select
Menu to exit
Setting Sleep Timer
Press the SLEEP button repeatedly to set a sleep time to automatically turn off the
unit. Each press of the button, the value changes as below.
Off
30 min.
60min.
90min.
120min.
Sleep Time: Off
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
Before calling for repair service, check the following items for possible remedies to an
encountered symptom.
Symptoms
Check item
"Ghost" or double images
This may be caused by obstruction to the antenna due to high rise buildings
or hills. Using a highly directional antenna may improve the picture.
No power
No picture
Check that the AC power cord is plugged into the mains socket.
Unplug the power cord, wait for 60 seconds. Then reinsert plug into
the mains socket and turn on the unit again.
Check antenna connections at the rear of the unit to see if it is properly
connected to the unit.
Possible broadcast station trouble. Try another channel.
Adjust the contrast and brightness settings.
Select a correct input.
Is a non-compatible signal being input?
Increase the VOLUME.
Check that the unit is not muted.
Good picture but no sound
Good sound but poor colour
Poor picture
Adjust the contrast, colour and brightness settings.
Sometimes, poor picture quality occurs when having activated an S-VHS
camera or camcorder connected and having connected another peripheral
at the same time. In this case, switch off one of the other peripherals.
Check whether the room is too bright.
This may be caused by electrical interference (e.g. hair dryer, nearby
neon lights, etc.)
Horizontal dotted line
Turn off the equipment.
Check whether the batteries are working. Replace if necessary.
Clean the remote control sensor lens on the unit.
Do not use the remote control under strong or fluorescent lighting.
The batteries should be inserted with polarity (+, -) aligned.
Television not responding to
remote control
Snowy picture and noise
Check the aerial connection.
No stable or not
synchronised D-Sub picture
Check if you have selected the correct D-Sub mode in your PC.
Adjust Balance in the SOUND (AUDIO) menu.
No output from one of the speakers
Controls buttons do not work
Unplug the power cord, wait for some seconds. Then re-plug the power
cord and turn on the unit again.
Do not use in hot and cold rooms (location)
When the unit is used in rooms (locations) with low temperature, the picture may leave trails or appear slightly delayed. This is no
a malfunction, and the unit will recover when the temperature returns to normal.
t
Do not leave the unit in a hot or cold location. Also, do not leaves the unit in a location exposed to direct sunlight or near a heater, as
this may cause the cabinet to deform and the LCD panel to malfunction.
(Storage temperature: 00C to +500C;
Working temperature: 50C to 400C.)
Note:
If your problem is not solved, restart your TV by turning it off and then on again once.
Never attempt to repair a defective TV yourself.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Care and Maintenance
LCD Display panel information
Note:
The marking or retained image on the LCD panel resulting from fixed image use is not an operating defect and as such is
not covered by Warranty. This product is not designed to display fixed image patterns for extended periods of time.
Important Information Regarding Use of Video Games, Computers, Captions or Other Fixed Image Displays.
The extended use of fixed image program material can cause a permanent "shadow image" on the LCD panel.
This background image is viewable on normal programs in the form of a stationary fixed image. This type of irreversible
LCD panel deterioration can be limited by observing the following steps:
A. Reduce the brightness/contrast setting to a minimum viewing level.
B. Do not display the fixed image for extended periods of time.
C. Turn the power off when not in actual use.
Note:
The marking or retained image on the LCD panel resulting from fixed image use is not an operating defect and as such is
not covered by Warranty. This product is not designed to display fixed image patterns for extended periods of time.
Cleaning and Maintenance
To clean this unit, wipe with a soft, dry cloth.
If the surfaces are extremely dirty, use a soft cloth dipped in a soap and water solution or a weak detergent solution.
Use eyeglass cleaner to remove stubborn dirt from the LCD.
Never use alcohol, paint thinner or benzine to clean this unit.
Before using a chemically treated cloth, read the instructions that came with the cloth carefully.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
PALSONIC CORPORATION PTY LTD
1 JOYNTON AVENUE
WATERLOO NSW 2017 AUSTRALIA
TEL: (02) 9313 7111
FAX: (02) 9313 7555
PALSONIC CUSTOMER SERVICE
TELEPHONE
AUSTRALIA: 1300 657 888
604-L20Y33-00
V1.0
Download from Www.Somanuals.com. All Manuals Search And Download.
|