NEC Projector XL 3500 User Manual

MultiSync Hivid 3500 Projector

Large Screen MultiSync Projection System

User’s Manual

Model number: XL-3500

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Important Safeguards

These safety instructions are to ensure the long life of your projector and to prevent fire and shock. Please read them carefully and heed

all warnings.

Installation

1. Place the projector on a flat, level surface and in a dry area free from dust and moisture.

2. Do not place the projector in direct sunlight, near heaters or heat radiating appliances.

3. Exposure to direct sunlight, smoke or steam could harm internal components.

4. Handle your projector carefully. Dropping or jarring your projector could damage internal components.

5. Do not place heavy objects on top of the projector.

6. If installing the projector on the ceiling:

a. The ceiling must be strong enough to support the projector and the installation must be performed in accordance with any local

building codes.

b. Qualified NEC authorized dealer personnel must install the projector.

Power Supply

1. The projector is designed to operate on a power supply of 2.3KW(MAX) AC200-240V 50/60Hz. Ensure that your power supply fits

this requirement before attempting to use your projector.

2. Handle the power cable carefully and avoid excessive bending. A damaged cord can cause electric shock or fire.

3. If the projector will not be used for an extended period of time, disconnect the plug from the power outlet.

4. Placing the power cord and the RGB cable closely to each other can cause beat noise. If this happens, keep the two separated until

beat noise is not generated

Cleaning

1. Unplug the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild detergent. Never use strong detergents or solvents such

as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful not to scratch or mar the lens.

Fire and Shock Precautions

1. Ensure that there is sufficient ventilation and that vents are unobstructed to prevent potentially dangerous concentrations of ozone

and the build-up of heat inside your projector. Allow at least 3 inches (10cm) of space between your projector and a wall.

2. Prevent foreign objects such as paper clips and bits of paper from falling into your projector. Do not attempt to retrieve any objects

that might fall into your projector. Do not insert any metal objects such as a wire or screwdriver into your projector. If something

should fall into your projector, disconnect it immediately and have the object removed by a qualified NEC service person.

3. Do not place any liquids on top of your projector.

CAUTION: High Pressure Lamp May Explode if Improperly Handled. Refer Servicing to Qualified Service Personnel.

Lamp Caution: Please read before operation

Due to the lamp being sealed in a pressurized environment, there is a small risk of explosion, if not operated correctly. There is

minimal risk involved, if the unit is proper working order, but if damaged or operated beyond the recommended 1500 hours, the

risk of explosion increases.

Please note that there is a warning system built in, that displays the following message when you reach 1500 hours of operation”

Lamp Running Time is Over 1500 Hours!!” When you see this message please contact your NEC Dealer for a replacement.

If the lamp does explode, smoke will be discharged from the vents located on the side of the unit. This smoke is comprised of

glass in particulate form and Xenon gas, and will not cause harm if kept out of your eyes. If your eyes have been exposed to this

gas, please flush your eyes out with water immediately and seek immediate medical attention. Do not rub your eyes! This could

cause serious injury.

WARNING:Do not look into the lens while the projector is on. Serious damage to your eyes could result.

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

Recommandations importantes

Ces instructions de sécurité ont pour but d'assurer une longue vie à votre projecteur et d'éviter un incendie ou une décharge

électrique. Prière de les lire avec attention et de tenir compte de tous les avertissements.

Installation

1. Placer le projecteur sur une surface plate et de niveau, et dans un endroit sec et à l'abri des poussières et de l'humidité.

2. Ne pas exposer le projecteur aux rayons directs du soleil, ni le placer près d'un chauffage ou de dispositifs de radiation de

chaleur.

3. L'exposition aux rayons directs du soleil, à la fumée ou à la vapeur pourrait endommager des composants internes.

4. Manipuler le projecteur avec précautions. Laisser tomber le projecteur ou lui donner des chocs pourrait endommager des

composants internes.

5. Ne pas poser d'objets lourds sur le dessus du projecteur.

6. En cas d'installation du projecteur au plafond :

a. Le plafond doit être assez résistant pour supporter le projecteur et l'installation doit être faite en conformité avec toute norme

de construction locale.

b.Le projecteur doit être installé par du personnel qualifié d'un revendeur agréé NEC.

Alimentation

1. Le projecteur est conçu pour fonctionner sous une tension d'alimentation de 2,3 KW (MAX) CA 200-240 V 50/60 Hz. S'assurer

que la tension du secteur soit conforme à ces caractéristiques avant d'utiliser le projecteur.

2. Manipuler le cordon d'alimentation avec précautions et éviter des flexions excessives. Un cordon endommagé peut occasionner

une décharge électrique ou un incendie.

3. Si le projecteur ne doit pas être utilisé pendant une longue période, débrancher la fiche de la prise de courant.

4. Placer le cordon d'alimentation et le câble RGB tout près l'un de l'autre peut occasionner un bruit de battement. Si cela se

produit, les maintenir séparés jusqu'à ce que le bruit de battement disparaisse.

Nettoyage

1. Débrancher le projecteur avant de le nettoyer.

2. Nettoyer régulièrement le boîtier extérieur avec un chiffon humide. S'il est très sale, utiliser un détergent doux. Ne jamais

utiliser de détergent forts ou de solvants tels que de l'alcool ou du diluant.

3. Utiliser un souffleur ou du papier pour objectif pour nettoyer l'objectif, et faire attention de ne pas griffer ou endommager

l'objectif.

Précautions contre l'incendie ou la décharge

1. S'assurer qu'il y ait une ventilation suffisante et que les ouvertures ne soient pas obstruées afin d'éviter des concentrations

potentiellement dangereuses d'ozone et l'accumulation de chaleur à l'intérieur du projecteur. Laisser au moins 10 cm d'espace

entre le projecteur et un mur.

2. Empêcher tous objets étrangers tels que des attaches trombones ou des morceaux de papier de tomber à l'intérieur du projecteur.

Ne pas essayer de récupérer des objets qui seraient tombés dans le projecteur. Ne pas introduire d'objets métalliques tels qu'un fil

ou un tournevis dans le projecteur. Si quelque-chose doit tomber dans le projecteur, le débrancher immédiatement et faire

enlever l'objet par un technicien agréé NEC.

3. Ne pas poser de liquides sur le dessus du projecteur.

ATTENTION : La lampe à haute pression peut exploser si elle est manipulée incorrectement. Confier l'entretien à du personnel

d'entretien qualifié.

AVERTISSEMENT :

Ne pas regarder dans l'objectif lorsque le projecteur est allumé. De sérieux dommages aux yeux pourraient en résulter.

Download from Www.Somanuals.com. All Manuals Search And Download.

VISUAL SYSTEMS DIVISION

LIMITED WARRANTY .

NEC Technologies, Inc.(hereafter NECTECH)warrants this prod-

uct to be free from defects in material and workmanship under the

following terms.

1. To obtain service on your product, consult the dealer from

whom you purchased the product, or ship it prepaid to any

authorized NECTECH service center.

2. Whenever warranty service is required, the original dated in

voice (or a copy) must be presented as proof of warranty

coverage, and should be included in any shipment of the

product. Please also include in any mailing, your name,

address and a description of the problem (s).

HOW LONG IS THE WARRANTY

Parts and labor are warranted for (1) One Year from the date of

the first customer purchase. The lamp is warranted for 1000

hours of operating time or 90 days, whichever comes first.

3. For the name of the nearest NECTECH authorized service

center, call NECTECH at 800-836-0655.

WHO IS PROTECTED

This warranty may be enforced only by the first purchaser.

LIMITATION OF IMPLIED WARRANTIES

All implied warranties, including warranties of merchantability

and fitness for a particular purpose, are limited in duration to the

length of this warranty.

WHAT IS COVERED AND WHAT IS NOT COVERED

Except as specified below, this warranty covers all defects in

material or workmanship in this product. The following are not

covered by the warranty:

EXCLUSION OF DAMAGES

1. Any product which is not distributed in the U.S.A., Canada, and

Mexico by NECTECH or which is not purchased in the U.S.A.,

Canada, and Mexico from an authorized NECTECH dealer.

If you are uncertain as to whether a dealer is authorized, please

contact NECTECH at 800-836-0655.

NECTECH’s liability for any defective product is limited to the

repair or replacement of the product at our option. NECTECH shall

not be liable for:

1. Damage to other property caused by any defects in this

product, damages based upon inconvenience, loss of use of

the product, loss of time, commercial loss; or

2. Any product on which the serial number has been defaced,

modified or removed.

2. Any other damages whether incidental, consequential or

otherwise. Some states do not allow limitation on how long an

implied warranty lasts and/or do not allow the exclusion or

limitation of incidental or consequential damages, so the

above limitations and exclusions may not apply to you.

3. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, abuse, neglect, fire, water, lightning or

other acts of nature, unauthorized product modification,

or failure to follow instructions supplied with the product.

b. Repair or attempted repair by anyone not authorized by

NECTECH.

c. Any shipment of the product (claims must be presented to

the carrier).

d. Removal or installation of the product.

HOW STATE LAW RELATES TO THE WARRANTY

This warranty gives you specific legal rights, and you may also

have other rights which vary from state to state.

e. Any other cause which does not relate to a product defect.

4. Cartons, carrying cases, batteries, external cabinets, mag-

netic tapes, or any accessories used in connection with the

product.

FOR MORE INFORMATION, TELEPHONE 800-836-0655

NEC TECHNOLOGIES, INC.

1250 N. Arlington Heights Road, Suite 500

Itasca. Illinois 60143-1248

WHAT WE WILL PAY FOR AND WHAT WE WILL NOT PAY FOR

We will pay labor and material expenses for covered items, but we

will not pay for the following:

NOTE: All products returned to NECTECH for service MUST

have prior approval. To get approval, call NEC Technologies at

800-836-0655.

1. Removal or installation charges.

2. Costs of initial technical adjustments(set-up), including ad-

justment of user controls. These costs are the responsibility of

the NECTECH dealer from whom the product was purchased.

3. Payment of shipping charges.

HOW YOU CAN GET WARRANTY SERVICE

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS.

INTRODUCTION

Introduction To The MultiSync Hivid 3500 Projector.............. 7

How Do You Get Started?....................................................... 7

What’s In The Box? ................................................................ 7

1.PART NAMES AND FUNCTIONS

Input Panel Features............................................................... 8

Remote Control Features ...................................................... 12

Remote Control Battery Installation...................................... 14

Ajusting and Setting (Adjust Menu).................................... 43

Source Registry ............................................. 43

Amplitude ..................................................... 48

White Balance ............................................... 48

Signal Level .................................................. 48

Uniformity .................................................... 49

Display Function ........................................... 50

Lamp Mode ................................................... 51

Set Option ..................................................... 52

Passcode ........................................................ 52

Setting Mode ................................................. 59

Menu Mode ................................................... 67

Execute Mode ............................................... 71

Help Menu .................................................... 74

Help ............................................................... 74

Topics............................................................ 74

Set Information ............................................. 74

Others .................................................................................. 75

Test Pattern ................................................... 75

Normalize/Load/Cancel ................................ 76

2.INSTALLATION

Setting Up Your MultiSync Hivid 3500 Projector.................. 16

Moving the Projector ............................................................ 16

Selecting A Location............................................................. 16

Screen Size and Projection Distance .................................... 16

Examples of Connections ..................................................... 20

Cautions on Connections...................................................... 20

When Used in Stand Alone Operation................................... 20

When Used with One Switcher (ISS-6020/ISS-6020G) ........ 21

When Used with Two or More Switchers (100 Inputs)......... 22

REMOTE 1 Connector........................................................... 24

3. OPERATION

General Controls................................................................... 26

Using The On-screen Menus ................................................ 27

On Adjustment Mode............................................................ 27

Menu Descriptions & Functions ........................................... 28

Task Bar ............................................................................... 28

Storing Projector Settings (Automatic Save Feature) ........... 29

4. SPECIFICATIONS ...................................... 78

5. APPENDIX

Basic Operation (Operate Menu)........................................... 30

Source Select ....................................................................... 30

Source Information............................................................... 32

Picture Control ..................................................................... 37

Display Control ..................................................................... 38

Image Control....................................................................... 39

Sound Control ...................................................................... 40

Closed Caption ..................................................................... 40

Timer Setting........................................................................ 41

Message List............................................................ 80

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION.

This section introduces you to your new MultiSync Hivid 3500 Projector, provides a list of materials that

comes with your projector and describes the features and controls.

Congratulations On Your Purchase Of The MultiSync Hivid 3500 Projector

The MultiSync Hivid 3500 is one of the very best projectors available today. Digital Light Processing^TM

(DLP^TM) by Texas Instruments enables you to project high bright precise images up to 500 inches across

(measured diagonally) from your PC or Macintosh computer (desktop or notebook), VCR, document camera,

laser disc player, DVD player and even an HD VCR or HD laser disc player.

You can use the projector on a tabletop or cart, you can permanently mount it on a ceiling*, or you can use

MultiSync Hivid 3500 Projector to project images from behind the screen. The wired remote control can be

used with a cable, and you can even use the wireless remote control.

The features you’ll enjoy include:

• A high-performance 1.6 KW Xenon lamp that delivers 3500 lumens (ANSI) and lamp life is 1500 hours.

• DLP offers true color reproduction.

• Display size can be altered to accommodate any picture size from 80 to 500 inches (measured diagonally).

• White Uniformity circuit keeps color of a large image evenly

• DLP projects images with uniform brightness onto screens while colors remain true to their original source.

• Magnifying, Reducing and Panorama mode allows you to make an image large or smaller and wider.

• Edge-blending feature provides a clean unbroken image of multiple screens.

• The new bulb type Xenon short arc lamp offers bright images and yet its long life.

• An image can be projected from in front or behind a screen, and the projector can even be installed on the

ceiling*.

• Supports HDTV and DVD signals as well as most IBM VGA, S-VGA, XGA(scaling), Macintosh or any

other RGB signals within a horizontal frequency range or 15 to 64 kHz and a vertical frequency range of 40

to 100 Hz. This includes NTSC, PAL, SECAM, and NTSC4.43 standard video signals.

• On-screen monitor out terminal allows you to view on-screen message on your PC when setting up your

system.

• The remote control can be used with or without a cable.

* Installing the MultiSync Hivid 3500 Projector on the ceiling must be done by authorized NEC technicians.

Consult your NEC dealer for more information.

How Do You Get Started?

The fastest way to get started is to take your time and do everything right the first time. Taking a few minutes

now to review the manual may save you hours later on. At the beginning of each section of the manual you’ll

find an overview. If the section doesn’t apply, you can skip it.

What’s In The Box?

Make sure your box contains everything listed. If any pieces are missing, contact your dealer. Please save the

original box and packing materials if you ever need to ship your MultiSync Hivid 3500 Projector.

• NEC MultiSync Hivid 3500 Projector

• Remote Control with Remote Cable (wireless/wired).

• Power Cable

• Two AA Batteries

• User Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS.

This compartment accommodates the remote control. The

remote control serves as the key panel on the projector

when it is plugged and fit in this compartment.

POWER ON/STANDBY Indicator

lights in green when the projector is turned on and

lights in red when the projector is in standby.

POWER

ON/STANDBY Indicator

OFF BREAKER ON

AC INPUT

OFF POWER ON

1 Breaker Switch

NOTE: Do not turn off the main power while “- -” on the

two digit display is blinking. During this time the lamp is

cooling off.

Press the switch to the ON position to turn on the breaker

and press to the OFF position to turn off the breaker.

When abnormal conditions are encountered, the breaker

will trip and turn the projector off.

6 POWER Indicator

If the projector will not be used for an extended period of

time, turn off the breaker by pressing the switch to the

OFF position.

Lights up when the projector is turned on.

7 STANDBY Indicator

2 Remote Sensor

Lights up when the projector’ s main POWER switch is on.

When the projector is used with the ISS-6020 switcher on

SW1 level or SW2 level mode, this indicator flashes when

the projector is not connected with the switcher correctily

or when the switcher is turned off.

Receives the signal from the supplied remote control

when used in the wireless mode.

3 Power Switch (Main power)

To turn on the main power to the projector press the

switch to the ON position (I). The STANDBY and the RC

READY indicator will light.

8 RC READY Indicator

Lights up when the projector’s main POWER switch is on.

Flashes when the projector receives a signal from the

remote control.

In this condition you can start up the projector by pressing

the POWER ON button on the remote control or the

POWER button on the side panel.

Press to the OFF position (0) to turn the main power off.

9 LAMP Indicator

NOTE: When turning off the main power, first return the

projector to the standby condition by pressing the

POWER OFF button on the remote control or the POWER

button on the side panel and then turn off the main

POWER switch. These procedures are necessary to

protect your projector and the connected equipment.

Displays the lamp on or off.

Indicator illuminates—Lamp is turned on

Indicator goes out-Lamp is turned off

0 Two Digit Display

INDICATOR: Displays projector error codes.(“00” in

normal operation)

ON/OFF Switch: Turns the INDICATOR on or off.

4 AC INPUT

Connect the supplied power cord here (AC 200-240V).

A REMOTE 2 Jacks

5 POWER Button

IN: for the wired remote control.

Turns the projector on when the projector is in the

standby condition (Main Power switch must be on and

the STANDBY indicator lit). Turns the projector off after

“- -” on the two digit display is blinking for three min-

utes.

OUT: for daisy-chaining multiple projectors and operating

them with the same remote control. To do so, connect to a

second projector’ s IN terminal to relay the input at the IN

terminal of the first projector until all the projectors are

connected.

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS

POWER STANDBY RCREADY LAMP

POWER ON/OFF

OFF ON

INDICATOR

REMOTE2

OPTION

OUT

REMOTE1

VIDEO

BNC RCA

VIDEO

S-VIDEO

R/Cr

G/Y

B/Cb

H/HV

OSD OUT

Loosen the screw by turning

and open to access the terminal

panel.

H I J K L

J VIDEO Input RCA Terminal (INPUT A)

B OPTION Connectors (D-Sub 9-pin)

For system expansion such as PC-control.

Connect to the RCA video output of the external equip-

ment such as a VCR or laser disk player.

IN: connect to the external equipment such as PC.

OUT: for daisy-chaining multiple projectors and operating

them with the same external equipment. To do so, connect

to a second projector’ s IN terminal to relay the input at

the IN terminal of the first projector until all the projectors

are connected.

K S-VIDEO Input Terminal (INPUT A)

Connect to the S-video output of the external equipment

such as a VCR with an S-video output.This terminal

allows switching between S2 and S1 VIDEO input modes.

See the “S-Video Mode” section for more information.

C REMOTE 1 Connector (Mini D-Sub 15-pin)

This terminal allows external control of the projector from

either the Switcher or from an external control. When the

Switcher is used, connect to the REMOTE 1 terminal on

the back of the Switcher.

L Active Indicator (green LED)

Lights up when the INPUT A slot is selected.

M R/Cr, G/Y, B/Cb, H H/V and V Input Terminals

(INPUT A)

NOTE: The ISS-6020/ISS-6020G Switcher is compatible

with this projector.

Connect R,G,B,H (Horizontal sync) and V (Vertical sync)

outputs of the external equipment such as the Switcher). If

using a component with a combined sync (SYNC)output,

connect it to the H/V terminal.

D INPUT E

Not used.

Connect component video outputs of the external equip-

ment such as DVD player.

E INPUT D

Used for the factory-installed video processor only.

N OSD OUT Connector (Mini D-Sub 15-pin)

Outputs on-screen information. You can use this connec-

tor to loop your on-screen information to an external

monitor.

F INPUT C

Slot for adding optional RGB or video input cards.

G INPUT B

NOTE:

Slot for adding optional RGB or video input cards.

1)A picture may be distorted or no picture may appear

when any one of the following procedures is performed:

* An XGA signal is input to the projector.

* A High-refresh signal in SVGA is input to the projector.

2)Some types of monitor may display no image on the screen.

H VIDEO Input BNC Terminal (INPUT A)

Connect to the BNC video output of the external equip-

ment such as a VCR or laser disk player.

I VIDEO Input Select Switch

Selects VIDEO input between BNC and RCA type.

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS

OPTIONAL Boards

VIDEO INPUT Board [XG VIDIN(A)]

Front view

VIDEO

S-VIDEO

VIDEO INPUT

AUDIO INPUT

VIDEO

S-VIDEO

1 Active Indicator (green LED)...... Lights up when this board is selected.

2 VIDEO INPUT Terminal ............... Connects composite video output signals.

3 S-VIDEO INPUT Terminal ........... Connects S-video output signals.

4 VIDEO INPUT Terminal ............... Connect to the audio outputs of the external equipment such as a VCR.

(Not available on this model.)

5 S-VIDEO INPUT Terminal ........... Connect to the S-video audio outputs of the external equipment such as a VCR

with S-video outputs. (Not available on this model.)

RGB INPUT Board [XG RGBIN(A)]

Front view

AUDIO INPUT

RGB INPUT

H/HV

1 Active Indicator (green LED)...... Lights up when this board is selected.

2 R Input Terminal.......................... Connects an Red output signal.

3 G Input Terminal ......................... Connects a Green output signal.

4 B Input Terminal.......................... Connects a Blue output signal.

5 H/HV Input Terminal.................... Connects horizontal sync or horizontal/vertical sync output signals.

6 V Input Terminal.......................... Connects a vertical sync output signal.

7 AUDIO Input Terminals............... Connect to the audio outputs of the external equipment such as ISS-6020/6020G.

(Not available on this model.)

RGB INPUT Board

Top view

8 Rotary Switch (S1001)

9 Jumper(S1002, S1003, S1004)

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS

The combination of the rotary switch and the jumper pins allows the projector to accept VIDEO signals. Note that this board cannot

accept RGB signals when board is set to VIDEO input.

Rotary switch (S1001)

Jumper (S1002, S1003, S1004)

Setting of Rotary switch

No.

Mark

VIDEO

OPTION

RGB

Input

VIDEO input

Option

RGB

RGB input

Not used

2, 4-9

*1 ) No 1 is for future system expansion.

*2) No 3 is factory preset.

Table for Setting Rotary Switch and Jumpers.

Input Signal

Setting of Rotary switch and Jumpers

Board Identification

B terminal

Rotary Switch(S1001)

Jumpers

G terminal

R terminal

VIDEO

RGB

(2, 3) Short

(1, 2) Short

* indicates factory preset.

SLOT FOR OPTIONAL MODULE

INPUT C slot

INPUT B slot

VIDEO

BNC RCA

VIDEO

S-VIDEO

R/Cr

G/Y

B/Cb

H/HV

OSD OUT

INPUT A slot

Corresponding slot number

You can also select the input signal directly by pressing the INPUT “1” through “10” button. In this case INPUT buttons function as

follows:

1) When the slot A(Mother board) is selected:

INPUT 1 ...... RGB input

3) When the slot C (optional board) is selected:

When VIDEO board installed

INPUT 7 ...... VIDEO input

INPUT 8 ...... S-VIDEO input

When RGB board installed

INPUT 7 ...... RGB input

INPUT 2 ...... VIDEO input

INPUT 3 ...... S-VIDEO input

2) When the slot B (optional board) is selected:

When VIDEO board installed

INPUT 4 ...... VIDEO input

INPUT 5 ...... S-VIDEO input

When RGB board installed

INPUT 4 ...... RGB input

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS

Remote control unit

1 Remote Jack

Insert the supplied remote cable here.

2 POWER Buttons (ON/OFF)

Press the ON button to turn the projector on when the

projector is in the standby condition (STANDBY and RC

READY indicators lit). Press the OFF button to return the

projector to the standby condition.

POWER

INPUT

1 ABC 2 DEF

OFF

3 GHI

TEST

4 JKL 5 MNO 6 PQR

7 STU 8 VWX 9 YZ/

10 ,. CAPTION

3 TEST Button

Press to display the TEST PATTERN menu from which

you can select a test pattern.

OPERATE ADJUST

PIC CTL SOUND CTL

OFF

4 ADJUST Button

Press to display the ADJUST menu.

PIC MUTE SOUND MUTE

DISPLAY HELP

INFO INPUT LIST

5 OPERATE Button

ZOOM/PAN POSITION KELVIN

Press to display the OPERATE menu.

SIG LEVEL

6 Backlight Switch

Turns the backlight on and off.

GAMMA

PIXEL CLK

PIXEL PHASE

CURSOR

ADDRESS

If no button operation is made within 30 seconds with the

Backlight ON, the Backlight will turn off to conserve

battery life. The light stays on in standby and power-on

when the remote control is used as a wired remote.

7 PIC CTL Button

Press to display the picture adjustment screen.

NOTE: Some function items will not be available depend-

ing on the type of video signal.

STORE

ENTER

DELETE

NORMAL

CTL

END

8 SOUND CTL Button

Press to display the VOLUME adjustment screen. You

can adjust the volume of the ISS-6020/ISS-6020G

Switcher. (when used with the ISS-6020 switcher on SW1

level or SW2 level mode)

9 PICTURE (PIC) MUTE Button

Press to mute the picture. Press again to display the

picture.

0 SOUND MUTE Button

You can use your remote control with the cable or wirelessly

to operate your MultiSync Hivid 3500 Projector.

Press to mute the sound. Press again to return the sound.

(when used with the ISS-6020 switcher on SW1 level or

SW2 level mode)

If you want to use your remote control with the cable, connect

one end of the cable to the jack on the remote control and the

other end to the REMOTE 2 IN jack of the projector.

A DISPLAY Button

Press to turn on or off the on-screen display. Pressing with

CTL eliminates the on-screen display; pressing with CTL

will restore display.

NOTE: Even if the on-screen display may be turned off

with pressing CTL and DISPLAY, any adjustment will

still change the projector’ s memory settings. This mode

is available even when an input is switched to another or

the power is turned off using the POWER OFF button on

the remote control.

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS

N POSITION Button

B HELP Button

Press to enter the position mode. You can adjust the

Press to display the explanation of the current selected

function and available functions.

O R, G, and B Buttons

C SIG LEVEL Button

The R and B buttons are used for Uniformity only.

Press to display the SIGNAL LEVEL menu. You can set

the level for an RGB or YUV signal.

P CURSOR Buttons

Used for increasing and decreasing control levels, cursor

movement and convergence adjustments.

D GAMMA Button

Press to display the GAMMA CORRECTON menu. You

can select two options.

Q DELETE Button

Used to delete characters or numbers you typed.

E ADDRESS Button

Press to display the ADDRESS menu. Pressing with CTL

allows you to specify the address for the remote control.

R NORMAL Button

Returns the standard level for each signal. When pressed

once, the confirmation message will be displayed. When

“YES” is selected and ENTER is pressed, the data will be

returned to the standard level. While holding down the

CTL button, press the NORMAL button to display the

LOAD menu to select the LOAD (last stored level).

F PIXEL CLK Button

Press to display the PIXEL CLOCK adjustment screen.

You can adjust a picture width to the screen by adjusting

the clock frequencies to eliminate the vertical banding in

the image.

S STORE Button

G PIXEL PHASE

Memorizes the adjustments setting of each signal sepa-

rately.

When pressed once, the confirmation message “STORE?”

will be displayed. When selecting “YES” and ENTER, the

data will be stored in memory.

Press to display the PIXEL PHASE adjustment screen.

You can adjust the clock phase to reduce video noise, dot

interference or cross talk. (This is evident when part of

your image appears to be shimmering.)

T END Button

H INPUT Button

Ends the adjustment mode.

Selects menus and switches input signals.

U ENTER Button

I CAPTION Button

Executes menu selection and switches to selected input.

Press to display the CLOSED CAPTION menu.

V CTL Button

J INFO Button

Used in conjunction with other buttons, similar to a shift

key on a computer.

Press to display the various parameters and settings of the

currently displayed image. Pressing with the CTL button

displays some of items available in.

K INPUT LIST Button

Press to display the memory list of the recorded input

signals.

L ZOOM/PAN Button

Press to display the ZOOM adjustment screen. The zoom

function enlarge or reduce the projected image. Pressing

with CTL displays the PAN adjustment screen. The pan

function enlarge or reduce the selected part of an image.

M KELVIN Button

Press to enter the KELVIN mode. You can adjust the

color temperature.horizontal, vertical position and

horizontal, vertical blanking and image size.

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS

Remote Control Battery Installation

1. Press firmly and slide the battery cover off.

2. Remove both old batteries and install new ones (AA).

Ensure that you have the batteries’ polarity (+/-) aligned correctly.

3. Slip the cover back over the batteries until it snaps into place.

NOTE: The remote control is powered by two alkaline 1.5V AA batteries.

Remote Control Precautions

• When using the remote wirelessly, you should be within 23 ft.(7 m) of the projector and at an angle of no more than 30 degrees.

• When the cable is connected to the remote control, it will not work wirelessly.

• Handle the remote control carefully.

• If the remote control gets wet, wipe it dry immediately.

• Avoid excessive heat and humidity.

• If you will not be using the remote control for a long time, remove the batteries.

• Do not mix new and old or different types of batteries.

• Avoid using the remote control as wireless with the backlight switch ON for an extended period of time. This can cause short

battery life.

• Be sure to secure the remote control with the metal fitting when installing the projector on the ceiling and using the remote

control as the key panel of the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

1.PART NAMES AND FUNCTIONS

When using the remote control as the key panel on the projector:

The following steps are necessary only when the projector is installed on

the ceiling.

When you use the projector in floor projection, you do not need to

fasten the remote with the metal fitting. Simply open the lid and put

the remote in the compartment.

1. Slide and open the lid.

Remote Control Unit

OPEN

2. Loosen the screw on the metal fitting.

3. Plug the mini plug into the remote jack of the remote control.

4. Place the remote control in the compartment.

5. Tighten the screw and secure the remote control with the

metal fitting.

Download from Www.Somanuals.com. All Manuals Search And Download.

2. INSTALLATION

This section describes how to set up your MultiSync Hivid 3500 projector and how to connect video and audio sources.

Setting Up Your MultiSync Hivid 3500 Projector

To set up and use your MultiSync Hivid 3500 Projector, you

must first do:

Pulling Out the Handles

Pull out the handle from the bottom side.

Retracting the Handles

1. Determine the screen size and the optional lens to be used.

Press down the two levers at the same time to retract the

handle.

NOTE: Consult your dealer for lens order and installation.

2. Set up a screen or select a non-glossy white wall onto

which you can project your image.

Moving The Projector

Always carry your projector by the handle. Ensure that the

power cord and any other cables connecting to video sources

are disconnected before moving the projector. When moving

the projector or when it is not in use, cover the lens with the

lens cap.

Selecting A Location

The further your projector is from the screen or wall, the larger the image. The minimum size the image can be

projected is 80" (2 m) measured diagonally. The largest the image can be is 500" (12.7 m).

WARNING

• Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and

the projector severely damaged.

• Do not use the projector where temperatures vary greatly. The projector must be used at temperatures

between 32 degrees F (0 degree C) and 104 degrees F (40 degree C).

• Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.

• Ensure that you have adequate ventilation around your projector so heat can dissipate. Do not cover the

vents on the bottom or back of the projector.

Screen Size and Projection Distance

1. Place your projector on a flat level surface at

Projector

Screen

the optimal distance from the screen or wall so

you realize the size image you want. (Avoid

having bright room lighting or sun light

directly on the screen or wall where you’ll be

projecting the image.)

2. Connect the power cable, remove the lens cap

and turn the projector on. (If no input signal is

available, the projector will display a black

screen.)

Screen center

Lens center

Projector

Screen

3. Ensure that the projector is square to the

screen.

4. Move the projector left or right to center the

image horizontally on the screen.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

5. To move the projected image up or down, rotate the

lens vertical knob in the top compartment right above

the lens barrel.

Lens vertical adjustment

6. Adjust the focus using the Focus knob at the lens.

7. Increase or reduce the size of the projected image by

using the ZOOM/PAN button on the remote control.

Focus adjustment

■ Projection Distance

Model No.

Fixed focal length lens

Zoom lens

XL-L1.27

1.27:1

XL-L1.5Z

XL-L3Z

Model No.

XL-L3

3.0:1

XL-L5

5.0:1

XL-L7

7.0:1

Magnification

Zoom1.5-3.0

Zoom3.0-7.0

6,100-14,220mm

240-600in

2580mm

6100mm

10160mm

400in

14220mm

560in

3,050-6,100mm

100"

200"

300"

400"

500"

102in

240in

120-240in

5160mm

203in

12190mm

480in

20320mm

800in

28450mm

1120in

6,100-12,190mm

240-480in

12,190-28,450mm

480-1120in

7740mm

305in

18290mm

720in

30480mm

1200in

42670mm

1680in

9,140-18,290mm

360-720in

18,290-42,670mm

720-1680in

10320mm

406in

40640mm

1600in

56900mm

2240in

24380mm

960in

12,190-24,380mm

480-960in

24,380-56,900mm

960-2240in

12900mm

508in

30480mm

1200in

50800mm

2000in

71120mm

2800in

15,240-30,480mm

600-1200in

30,480-71,120mm

1200-2800in

Vertical

offset

1/2V

1/4V

V=Screen Height (inch)

NOTE: “Vertical Offset” refers to as movable range between lens center and screen center. Vertical offset is decided by ratio of screen

height (V).

Example: When using a 100" screen (4:3) with the lens (XL-L 1.27), you can get 30 inches of your vertical offset by using the

formula (100 x 3/5 x 1/2) and you can make your screen height larger by 30 inches.

*For screen sizes between 80" and 500" not indicated on the above table, use the following proportional formula:

Diagonal screen size (4:3) x 4/5 = Screen width

W(Screen width) x magnification = Projection distance

Unit=inches

NOTE: The margin of error for projection distance is +/- 3% in fixed-focal-length lens and +/- 5% in zoom lens.

Six lenses are available. The four are fixed-focal-length lenses; the two are zoom lenses.

Order lens from your NEC dealer using lens’ s model number. Consult your NEC dealer for lens installation and replacement.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

Ceiling Installation

the projector’ s performance will be affected and its reliabil-

ity will decrease. Be sure to position the projector properly.

Installing your MultiSync Hivid 3500 Projector on the ceiling

must be done by a qualified technician. Contact your NEC

dealer for more information.

The manufacturer will not be held responsible for any

problems occurring when the projector is not installed in the

proper position.

Do not attempt to install the projector yourself.

The following shows the proper relative positions of the

projector and screen. Refer to the table to determine the

position of installation.

If your projector is mounted on the ceiling and your image is

upside down, use PJ ORIENTATION on the ADJUST-

SETTING Menu to correct the orientation. (See page.)

Install in such a way that the projector and screen are posi-

tioned in the proper direction and at the proper angle. If not,

26.93''

(684mm)

Projection distance

11.61''

(295mm)

Lens center

Vertical offset

Screen center

Model No.

Zoom lens

Fixed focal length lens

Model No.

Magnification

XL-L1.27

1.27:1

XL-L1.5Z

XL-L3Z

XL-L3

3.0:1

XL-L5

5.0:1

XL-L7

7.0:1

Zoom1.5-3.0

Zoom3.0-7.0

6,100-14,220mm

240-600in

2580mm

6100mm

10160mm

400in

14220mm

560in

3,050-6,100mm

120-240in

100"

200"

300"

400"

500"

102in

240in

5160mm

203in

20320mm

800in

28450mm

1120in

12190mm

480in

6,100-12,190mm

240-480in

12,190-28,450mm

480-1120in

7740mm

305in

18290mm

720in

30480mm

1200in

42670mm

1680in

9,140-18,290mm

360-720in

18,290-42,670mm

720-1680in

10320mm

406in

24380mm

960in

40640mm

1600in

56900mm

2240in

12,190-24,380mm

480-960in

24,380-56,900mm

960-2240in

12900mm

508in

50800mm

2000in

71120mm

2800in

30480mm

1200in

15,240-30,480mm

600-1200in

30,480-71,120mm

1200-2800in

Vertical

offset

1/2V

1/4V

V=Screen Height (inch)

NOTE: “Vertical Offset” refers to as movable range between lens center and screen center. Vertical offset is decided by ratio of screen

height (V).

Example: When using a 100" screen (4:3) with the lens (XL-L 1.27), you can get 30 inches of your vertical offset by using the

formula (100 x 3/5 x 1/2) and you can make your screen height larger by 30 inches.

*For screen sizes between 80" and 500" not indicated on the above table, use the following proportional formula:

Diagonal screen size (4:3) x 4/5 = Screen width

W(Screen width) x magnification = Projection distance

Unit=inches

NOTE: The margin of error for projection distance is +/- 3% in fixed-focal-length lens and +/- 5% in zoom lens.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

Reflecting The Image

Using a mirror to reflect your projector’s image enables you

to enjoy a much larger image. Contact your NEC dealer if you

need a mirror.

If you’re using a mirror and your image is inverted, use the

ADJUST-SETTING Menu to access to correct the orientation.

(See page 59.)

Rear Screen Projection

You can use your MultiSync Hivid 3500 to project an image

from the rear onto a transparent screen. The distance the

projector must be from the screen is the same as if you were

projecting the image from the front. Contact your NEC dealer

if you need a transparent screen.

If you’re projecting the image from the rear and your image is

inverted, use the ADJUST-SETTING Menu to access to

correct the orientation. (See page 59.)

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

EXAMPLES OF CONNECTIONS.

CAUTIONS ON CONNECTIONS:

• Unplug the projector and other equipment from the AC

supply before making connections.

• Make sure that the plug of the power cord is properly

connected to the power outlet. A loose connection may cause

hum or noise.

• Confirm your connection layout with the user’s manual

accompanying the equipment to be connected with the ISS-

6020/ISS-6020G Switcher.

When Used in Stand Alone Operation

Components with RGB and H/V

SYNC outputs such as a personal

computer.

VCR with S-video outputs.

VIDEO

BNC RCA

VIDEO

S-VIDEO

R/Cr

G/Y

B/Cb

H/HV

OSD OUT

VCR with S-Video outputs

PC Monitor

• Make sure that the STANDALONE mode is selected from the CONNECT CONDITION menu. See page 71 for connecting the

Switcher.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

When Used with One Switcher (ISS-6020/ISS-6020G)

Up to 10 input signals can be accepted when the projector is connected to one Switcher. Using the projector with the Switcher

allows easy adjustment and signal selection.

REMOTE2

OPTION

OUT

REMOTE1

To REMOTE1

VIDEO

BNC RCA

VIDEO

S-VIDEO

R/Cr

G/Y

B/Cb

H/HV

OSD OUT

To INPUT A (RGB,H/V,V inputs)

5BNC-5BNC coaxial cable 3BNC-3BNC cable(sync on green)

(separate sync)

(recommended)

4BNC-4BNC cable(composite)

Optional control cable 15p-15p

(CTL-6010)

To SYSTEM CONTROL

REMOTE 1

From R, G, B, H/V on separate H and

V. on the RGB OUTPUT module

The Switcher ISS-6020/ISS-6020G

VCR

Personal computer

• Make sure that the SW1 LEVEL mode is selected from the CONNECT CONDITION menu. See page 71 for the information in

detail.

• For more information on the Switcher, refer to the user’s manual accompanying the ISS-6020/ISS-6020G Switcher.

• All cables mentioned above are optional.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

When Used with Two or More Switchers (100 Inputs)

Up to 100 inputs can be accepted using the Switcher.

How to make connections:

1 Connect the REMOTE 1 terminal of the master Switcher

to the REMOTE 1 of the projector using the optional

control cable (15p-15p/CTL-6010).

NOTE:

• Be sure to set all the slide switches (S8603) of the

Switcher to RS-422 positions. Set the one on the last slave

Switcher to the appropriate position to match the con-

nected equipment such as a personal computer. (RS-422/

RS-232C for PC control of projector)

2 Next connect the REMOTE 2 terminal of the master

Switcher to the REMOTE 1 terminal of the first slave

Switcher using the same optional control cable as men-

tioned above. Third, connect the REMOTE 2 terminal of

the first slave to the REMOTE 1 of the second slave, and

the REMOTE 2 terminal of the second slave to the

REMOTE 1 terminal of the third slave (— and the

REMOTE 2 of the ninth slave to the REMOTE 1 of the

tenth slave). Connect all the Switchers with optional

control cables.

• Set the DIP switch S8601 of the Switcher.

Signal

Switcher

SLAVE 1

Signal

REMOTE 1

REMOTE 2

OPTION (PC)

10 inputs

REMOTE

CONTROL

Signal

REMOTE 1

REMOTE 2

To SLOT 1

To SLOT 2

SLAVE 2

MASTER

SWITCHER

Signal

To SLOT 10

SLAVE 3

REMOTE 1

REMOTE

Projector

REMOTE 1

REMOTE 2

To REMOTE 2

SLAVE 9

Signal

REMOTE 1

REMOTE 2

10 inputs

SLAVE 10

OPTION

(PC)

• Make sure that the SW2 LEVEL mode is selected from the CONNECT CONDITION menu. See page 71 for the information in

detail.

• Refer to the user’s manual accompanying the Switcher.

• Cables mentioned are not included with the projector.

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

Set the DIP switch (S8601) of the Switcher as follows:

NOTE: Slave numbers 1 to 10 must correspond to the master’s slot numbers 1 to 10.

ISS-6020

ISS-6020G

Output to

Setting of S8601

OPEN

Master

Slave 1

Slave 2

Slave 3

Slave 4

Slave 5

Slave 6

Slave 7

Slave 8

Slave 9

Slave 10

The Projector

OPEN

Slot 1 of the Master

Slot 2 of the Master

Slot 3 of the Master

Slot 4 of the Master

Slot 5 of the Master

Slot 6 of the Master

Slot 7 of the Master

Slot 8 of the Master

Slot 9 of the Master

Slot 10 of the Master

OPEN

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

REMOTE 1 Terminal

15 14 13 12 11

This terminal is used for either connecting the ISS-6020/ISS-6020G Switcher or a third party external control device. When the

Switcher is used, connect it with the optional control cable (15-15 pin; 50 ft./16m; CTL-6010) to this terminal.

When used with the Switcher.

Pin No.

FUNCTION

1, 2, 6 and 7

Sending and receiving data when the Switcher is used.

Identifying the Projector

Ground

Others

Used inside the Projector. Normally set to OPEN.

When using with the Switcher ISS-6020/ISS-6020G, connect no. 1,2,6,7,9 and15 pins of the projector to the same no. pins of the

switcher as shown below.

REMOTE 1 terminal of the Projector

mini D-sub 15 pin (male)

REMOTE 1 terminal of the Switcher

mini D-sub 15 pin (male)

Shield (frame ground)

Pins without a number are open.

Pin Configuration of Optional CTL-6010 Cable

Download from Www.Somanuals.com. All Manuals Search And Download.

2.INSTALLATION

When used in stand alone operation.

FUNCTION

Pin No.

SHORT/OPEN

External control mode ON

External control mode OFF

SHORT

OPEN

POWER ON

POWER OFF

SHORT

OPEN

PICTURE MUTE ON

PICTURE MUTE OFF

SHORT

OPEN

4,8,11,12

INPUT-A RGB

VIDEO

OPEN

SHORT

OPEN

SHORT

S-VIDEO

SHORT OPEN

SHORT SHORT

COMPONENT

COMPONENT(HDTV)

OPEN

INPUT-B RGB

VIDEO

OPEN

SHORT

OPEN

SHORT

OPEN

SHORT SHORT OPEN

SHORT SHORT SHORT

S-VIDEO

OPEN

COMPONENT

COMPONENT(HDTV)

SHORT

OPEN

SHORT

INPUT C RGB

VIDEO

SHORT

OPEN

SHORT OPEN

SHORT SHORT

S-VIDEO

SHORT SHORT

OPEN

COMPONENT

COMPONENT(HDTV)

SHORT

SHORT SHORT SHORT OPEN

The term “SHORT” means to connect with pin 15

• When in the external control mode, the POWER, INPUT and PICTURE MUTE buttons on the remote control will not function.

NOTE: Pin 13 is the external remote signal terminal. The projector can be controlled by the same format signal as the supplied

remote control from the external controller regardless of setting Pin 14.

NOTE: When turning off the power to the projector using the external control, do not disconnect the plug from the power outlet.

These procedures are to protect your projector and the connected equipment.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

This section describes how to select a computer or video source and how to adjust the picture and sound,

General Controls

Before you turn on your MultiSync Hivid 3500 Projector ensure that the computer or video source is turned

on and that your lens cap is removed.

1. Turn On The Projector

The breaker switch and the main power switch are on the back panel of the MultiSync Hivid 3500

Projector. By turning these switch on, the projector will go into its standby mode and the POWER ON/

STANDBY indicator will glow red. Only after you press the 'On' button on the remote control or projector

cabinet will the POWER ON/STANDBY light turn to green and the projector become ready to use.

2. Select The Computer Or Video Source

Press the INPUT button on the remote control to display the image. Or press the Operate button on the

remote control and use the Source Selection to select your video source: Video, S-Video, RGB or Y/Cr/

Cb.

NOTE: When the message "New Signal" is displayed, register the signal in the Source Registry menu.

3. Adjust The Image and The Sound

Press the PIC CTL button on the remote control or use the Operate-Picture Control menu to adjust the

picture. Press the SOUND CTL button on the remote control or use the Operate-Sound Control menu to

increase or decrease the volume.

4. Turn Off The Projector

First press the POWER button on the remote control or the projector cabinet. The STANDBY light will

glow. Allow the fan to cool the projector for three minutes. This will extend the life of the lamp. Then turn

off the main power switch on the back panel. The power light will go out. Last turn off the breaker switch

on the back panel.

IMPORTANT:

• The projector should be unplugged if it will not be used for an extended period.

• If you want to turn off the image briefly (five minutes or less), press the PIC MUTE button instead

of turning the projector off and on.

• The projector will display a message "No Signal !!" if no input signal is present.

• Do not turn the projector off and then immediately back on. The Projector needs to cool down for

three minutes before it is powered on again.

CAUTION: Do not unplug the projector or turn off the main power while the cooling fan is on and the

"--" on Two Digit display is blinking for three minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Using The On-Screen Menus

1. Press the OPERATE or ADJUST button on the remote control to display the Operate or Adjust menu.

2. Use the

button on the remote control to highlight the "1. Ope.", "2. Adj." or "3. Help" in yellow and the selected menu will

drop down.

3. Press the

or button to highlight the item you want to adjust or set in the selected menu.

4. Press the ENTER button on the remote control to select the item.

5. Adjust the level or turn the selected item on or off by using the

will show you the amount of increase or decrease.

buttons on the remote control. The on-screen gauge

6. Press the STORE button on the remote control to store the change.

NOTE: The change is stored automatically when the Automatic Save ("Auto Data Store") Feature mode is set to "ENABLE" See

page 64.

7. Repeat steps 2-5 to adjust an additional item, or press the END button on your remote control to quit.

On Adjustment Mode

The Adjustment mode contains various adjustment items for set-up.

Open the Adjustment menu and select the item you wish to adjust.

To display the ADJUST menu, proceed as follows:

1 Press the ADJUST button.

• The projector may ask for your passcode.

2 Enter your registered passcode.

P A S S C O D E ?

When a passcode has not been registered:

****

• Since no passcode is programmed at the factory, pressing the

ADJUST button will open the Adjustment menu.

• See “Entering Passcode”, “Registering Passcode”, “Changing

Your Passcode” and “Canceling Your Passcode” on pages 52

through 58.

When your passcode has already been registered:

• When finishing the Adjustment mode, the “RETURN USER

MODE?” menu will be displayed. If you select “Yes” and

press ENTER to end the Adjustment mode, you will have to

enter your passcode to re-enter the Adjustment mode.

• When finishing the Adjustment mode by either selecting

“No” or pressing END, you do not need to enter your

passcode to re-enter the Adjustment mode. To exit the

Adjustment mode temporarily during adjusting, select “No”.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Menu Descriptions & Functions

Access of all set-up functions is done through the menu system. Depending upon button selection, your desired screen will be dis-

played as shown below:

NOTE: Some function items will not be available on the input video signal or connected peripheral equipment. Functions not

available are indicated in gray.

Operate Menu

Adjust Menu

Help Menu

1. Ope.

2. Adj

3. Help

1. Ope.

2. Adj

3. Help

1. Ope.

2. Adj

3. Help

-Operate-

-Adjustment-

-Help-

1. Source Select

1. Source Registry

2. Amplitude

3. White Balance

4. Signal Level

5. Uniformity

6. Display Function

7. Lamp Mode

8. Set Option

1. Help

2. Topics

3. Set Information

2. Source Information

3. Picture Control

4. Display Control

5. Image Control

6. Sound Control

7. Closed Caption

8. Timer Setting

Typical keys on the remote control work as follows:

OPERATE : Accesses the Operate menu.

ADJUST : Accesses the Adjust menu.

: Selects the next upper item in the menu. Or increases the adjustments.

: Selects the next lower item in the menu. Or decreases the adjustments.

: Selects the next right side item in the menu or task bar. Or increase the adjustments.

: Selects the next left side item in the menu or task bar. Or decrease the adjustments.

ENTER : Proceeds to the selected menu choice or to the selected adjustment.

END : Returns to the previous menu or exits the selected function.

INPUT(1-10) : Directly switches to the corresponding input or opens the corresponding sub menu or item.

About Task bar

The mens (Operate, Adjust or Help) has the common bar across the top of the menu. This is called the Task bar. A press of either of the

OPERATE or ADJUST button on the remote control displays the task bar with the menu.

On-Screen Menu Elements:

Highlight: Indicates the selected menu in yellow; indicates the selected control in white back.

Delta symbol ( ) in the menu or sub menu: Indicates further choices are available. Use the ENTER button to open the pull-down

menu.

Inverted delta symbol ( ) in the adjustment or setting screen: Indicates further choices are available. Use the ENTER button to

open the pull-down menu. Note that a solid inverted delta symbol ( ) indicates the item is currently selected.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Storing Projector Settings (Automatic Save Feature)

You have two options to store projector settings in the memory: auto-

matically and manually.

* The Automatic Save Feature mode has been set to "DISABLE" by

factory. For information on setting, see "Automatic Auto Data Store"

on page 64.

■ When the Automatic Save Feature mode is set to "ENABLE", pro-

jector settings will be stored in the projector' s memory automati-

cally.

Settings are stored automatically when any one of the following

procedures is performed:

• One input is switched to another.

• The projector is turned off.

• After every 10 minutes of elapsed time.

■ When the Automatic Save Feature mode is set to "DISABLE", pro-

jector settings can be stored in the projector' s memory manually.

When you try to return the source screen by pressing END several

times, the "STORE?" menu is displayed.

To manually save settings, proceed as follows:

1. Use the END button to display the "STORE" menu from the cur-

rent adjustment screen or menu.

S t o r e

Y e s

2. Use the CURSOR

press ENTER.

button to highlight "Yes" or "No" and

N o

Items to select

• Yes ---- Overwrites the currently projected signal and saves

the settings. Note that "Yes" is available only for

registered signals.

• No ----- Does not save settings.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Basic Operation (Operate Menu)

Source Select

Enables you to select a source such as a VCR, laser disk player,

DVD player, or computer.

P O 1 / 1 0 - 1

S o u r c e S e l e c t

S t a n d A l o n e

O p t i o n

N o N a m e

0 1

0 2 N T S C

0 3 7 8 K

0 4

S o u r c e

I n p u t

• Use the CURSOR

button to highlight the source to be

V I D E O

R G B

switched to and press the ENTER to the selected source.

0 5 N T S C

0 6 N o 4 0

0 7 N o 3 9

0 8 3 1 . 4 5 K

V I D E O

R G B

V I D E O

0 9

1 0

NOTE:

O u t p u t D a t a : L i s t N o . x x x

• The Source Select menu has 10 pages. Each page consists of two

sheets. Press the

button to go on to the next sheet or

the previous sheet.

• To advance to the next page or to the previous page, hold down

the CTL button then press the CURSOR or . To

directly access the page, hold down the CTL button then any one

of the INPUT buttons.

P O 1 / 1 0 - 2

S o u r c e S e l e c t

f h f v

S t a n d A l o n e

K e y

N o D a t e

0 1

0 2

1 5 . 7 4

7 8 . 3 6

6 0 . 0 7

7 2 . 2 8

C T L 1 0

0 3

0 4

0 5

1 5 . 7 4

3 7 . 9 3

3 7 . 5 5

3 1 . 4 8

1 5 . 3 5

1 5 . 3 7

6 0 . 0 7

6 0 . 5 2

7 5 . 1 0

5 9 . 9 6

5 1 . 8 5

5 1 . 9 2

0 6

0 7

+ 5

C T L

0 8 J a n / 0 1 / 1 9 9 8

0 9 J a n / 0 1 / 2 0 0 0

1 0 J a n / 0 1 / 2 0 4 0

O u t p u t D a t a : L i s t N o . x x x

To select a source using the INPUT buttons on the remote

control when no menus are displayed:

1) Press the INPUT "0" button.

• The Select Terminal menu is displayed.

2) Use the CURSOR

wish to input.

button to select an input terminal you

3) Press the ENTER button to execute selection and to switch to the

selected input. To cancel, press any one of the INPUT buttons.

INPUT SELECT List Format

Page / total pages – sheet No.

Connect condition of the Switcher

P O 1 / 1 0 - 1

S o u r c e S e l e c t

P O 1 / 1 0 - 2

S o u r c e S e l e c t

f h f v

S t a n d A l o n e

O p t i o n

S t a n d A l o n e

K e y

N o N a m e

0 1

0 2 N T S C

0 3 7 8 K

0 4

S o u r c e

I n p u t

N o D a t e

0 1

V I D E O

R G B

0 2

1 5 . 7 4

7 8 . 3 6

6 0 . 0 7

7 2 . 2 8

C T L 1 0

0 3

0 4

0 5 N T S C

0 6 N o 4 0

0 7 N o 3 9

0 8 3 1 . 4 5 K

V I D E O

R G B

0 5

1 5 . 7 4

3 7 . 9 3

3 7 . 5 5

3 1 . 4 8

1 5 . 3 5

1 5 . 3 7

6 0 . 0 7

6 0 . 5 2

7 5 . 1 0

5 9 . 9 6

5 1 . 8 5

5 1 . 9 2

0 6

ᮤ

ᮣ

R G B

0 7

R G B

V I D E O

+ 5

C T L

0 8 J a n / 0 1 / 1 9 9 8

0 9 J a n / 0 1 / 2 0 0 0

1 0 J a n / 0 1 / 2 0 4 0

0 9

1 0

O u t p u t D a t a : L i s t N o . x x x

Horizontal Frequency

Signal name

Rgistered input module

Vertical Frequency

Entry date

Input terminal

Output data for the signal currently projected.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

NOTE:

• While you are viewing a source screen, you can also select the input signal directly by pressing the INPUT “1” through “10”

button. In this case INPUT buttons function as follows:

When using the projector in stand alone operation:

Input Mode

COMPONENT

(HDTV)

RGB

S–VIDEO

Slot Selection

VIDEO

COMPONENT

Input Module

Numbers designate INPUT buttons on the remote control.

When using the projector with the ISS-6020/ISS-6020G:

INPUT 1 through 10 → Selects the corresponding number slot of the ISS-6020/ISS-6020G

When using the projector with two ISS-6020/ISS-6020G or more:

To switch to another input signal, enter the master slot number, then the slave slot number by using INPUT buttons and press

ENTER.

Example:If you want to select a signal from the no.3 slot of the slave Switcher which is connected to the no.2 slot of the master Switcher, first

press the INPUT “2” button, then the INPUT “3” button and then press ENTER.

• You can switch to any input signal of NO 01 through10 on the Source Select list by holding down the CTL button and pressing

one of the INPUT buttons corresponding to the input number. To activate this function you must first select ENABLE in the Direct

Key. For further details, contact your dealer.

• If there are two or more memory locations that contain the same signal information the projector will reference the signal nearest

the beginning of the list. To select the next signal use the CURSOR or button and press ENTER.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Source Information

Provides and changes information for the parameters of your current

projected source.

NOTE: For other registered signals, change their parameters on the

Source Registry menu.

The menu items you can display, change or specify are as follows:

Source Name--------------- Changes a user name that has previ-

ously been entered.

Direct Key ------------------ Assigns settings of source to each

INPUT button (1-10) with CTL.

Input Slot ------------------- Selects an input terminal for the

registered signal when you need to do

)

1 / 2

(

[

]

[

]

due to adding optional equipment.

(

)

(

)

Signal System-------------- Displays the signal system of the

current source such as RGB, Video, S-

Video, or Component signal.

Video System -------------- Displays the current video standard.

Sync Frequency (H/V)----- Displays the current sync frequency.

Sync Polarity (H/V) -------- Displays the current sync polarity.

Sync System --------------- Selects the detection method of the

sync signal.

)

]

2 / 2

(

[

]

[

]

Sync Termination---------- Selects the impedance of the sync

signal.

Display Mode -------------- Selects the image display mode.

Color Matrix ---------------- Selects the mode to match the output

format of an HDTV or DVD signal.

CTI Control ----------------- Turns this feature on so you can make

(Color Transient Improvement)

the color sharper.

Noise Reduction ----------- Turns this feature on so video noise can

be reduced.

Stadium Mode ------------- Selects this feature so the picture is

expanded in the horizontal and vertical

directions at different ratios.

Source Select Counter ---- Resets the number of times a signal is

selected for display.

Source Display Timer ----- Resets the time of signal display.

Use the CURSOR

view or set.

button to select the item you want to

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

The following items can be set:

■ Source Name

To change the source name or input a new source name by

selecting one character at a time with the INPUT buttons 1

through 10 and by moving the cursor with the CURSOR button.

Only after completely finishing the selection of the characters,

press ENTER.

• If you have made an error, use the CURSOR button and reenter

the correct letter or number.

To delete one character, move the highlight to the character to be

deleted and then press the NORMAL button.

To delete all the entered name, hold down the CTL button then

press the NORMAL button.

• The above is the same procedure of the signal entry. See To

change the source name or input a new source name by select-

ing one character at a time with the INPUT buttons 1 through

10 and by moving the cursor with the CURSOR button. Only

after completely finishing the selection of the characters, press

ENTER.

To delete one character, move the highlight to the character to be

deleted and then press the NORMAL button.

To delete all the entered name, hold down the CTL button then

press the NORMAL button.

• The above is the same procedure of the signal entry. See pages

45 and 46 for more details.

■ Direct Key

Use the CURSOR buttons to assign settings of a source to each of

the 10 INPUT buttons with CTL.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Input Slot

You can select the input terminal for the registered signal. This

feature is useful when you need to change the input terminal due

to adding optional equipment.

NOTE: This setting cannot be done to the current projected

signal.

When used in the stand alone operation:

Use the CURSOR

button to select an input slot from

three slots: INPUT A, INPUT B, and INPUT C, and press

ENTER.

1 . I N P U T

2 . I N P U T

3 . I N P U T

Items to select

• INPUT A .............. Standard installed terminal

• INPUT B .............. Optional board terminal

• INPUT C .............. Optional board terminal

When used with a single Switcher ISS-6020/ISS-6020G:

M A S T E R

Use the CURSOR

button to select the desired slot

S L O T – 0 1

S L O T – 0 2

S L O T – 0 3

S L O T – 0 4

S L O T – 0 5

S L O T – 0 6

S L O T – 0 7

S L O T – 0 8

S L O T – 0 9

S L O T – 1 0

number "1" through "10" of the Switcher and press ENTER.

When used with two or more Switchers ISS-6020/ISS-6020G:

M A S T E R

S L O T – 0 1

S L O T – 0 2

S L O T – 0 3

S L O T – 0 4

S L O T – 0 5

S L O T – 0 6

S L O T – 0 7

S L O T – 0 8

S L O T – 0 9

S L O T – 1 0

S L A V E

Use the CURSOR

button to select the master slot

S L O T – 0 1

S L O T – 0 2

S L O T – 0 3

S L O T – 0 4

S L O T – 0 5

S L O T – 0 6

S L O T – 0 7

S L O T – 0 8

S L O T – 0 9

S L O T – 1 0

number "1" through "10" first from the master menu, then select

the slave slot number "1" through "10" from the slave menu and

press ENTER.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Sync System

This function is used to select the detection method of the sync

signal for an RGB signal.

Use the CURSOR

button to select "AUTO", "G-SYNC",

or "TRI-SYNC" and press ENTER.

• When "AUTO" is selected, the sync type will be displayed.

• Select "AUTO" in normal operation.

On-screen display

• AUTO --------- Detects automatically a composite or HV

separate sync signal.

• G-SYNC ------ Selects sync on green signal.

• TRI-SYNC ----Selects a tri-sync signal (HDTV signal).

■ Sync Termination

This functions is used to select the impedance of the sync signal.

Use the CURSOR

then press ENTER.

button to select " 75 Ω" or "Hi-Z",

NOTE: The default setting is "75 Ω".

This should be "75 Ω" for normal use. Select the "Hi-Z" when

inputting a TTL signal.

■ Display Mode

This function is used to select the image display mode such as

VGA, SVGA or Mac.

Use the CURSOR

button to select the desired mode and

press the ENTER button.

■ Color Matrix

This function is used to select the mode to match the output

format of an HDTV or DVD signal.

Use the CURSOR

button to select the appropriate mode

and press the ENTER button.

■ CTI(Color Transient Improvement) Control

This functions is used to turn this feature on so you can make the

color sharper.

Use the CURSOR

button to select either On or Off and

press the ENTER button.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Noise Reduction

This function is used to turn this feature on so video noise can be

reduced.

Use the CURSOR

button to select either On or Off and

press the ENTER button.

■ Stadium Mode

This feature is used to select this feature so the picture is ex-

panded in the horizontal and vertical directions at different ratios.

Use the CURSOR

button to select either Stadium or

Normal and press the ENTER button.

■ Source Select Counter

This is used to reset the number of times a signal is selected for

display.

When "Source Select Counter" is selected, the message "Do you

want to reset the Source Select Counter ? Yes No" is displayed.

Use the CURSOR

button to select either Yes or

No and press the ENTER button.

■ Source Display Timer

This function is used to reset the time of signal display.

When "Source Display Time" is selected, the message "Do you

want to reset the Source Display Timer ? Yes No" is displayed.

Use the CURSOR

button to select either Yes or

No and press the ENTER button.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Picture Control

Provides access to controls for your image such as brightness,

contrast, color, sharpness, hue, color temperature, gamma correction.

NOTE: Color, tint, and sharpness are available for an RGB source

only.

1. Use the CURSOR

button to select the item you

want to adjust and press the ENTER button.

Items to select

• Brightness ------------ Adjusts the overall image and background

screen brightness.

• Contrast --------------- Adjusts the image brightness in relation to

the background.

• Color ------------------ Adjusts the color intensity of the image.

• Sharpness ------------ Adjusts the detail of the image.

• Hue -------------------- Adjusts the red and green values of the

image.

-Picture Control-

1. Brightness

2. Contrast

3. Color

4. Sharpness

5. Tint

Hue

6. Color Temperature

7. Gamma Correction

• Color Temperature--- Adjusts the color temperature.

• Gamma Correction--- Adjusts the brightness of a dark area on the

screen.

2. Use the CURSOR buttons to adjust the picture to your desired

setting.

The CURSOR

button increases the level.

button decreases the level.

[

]

*For Gamma Correction, follow the instructions below.

1. Use the CURSOR or button to select either "Table" or

"User Table" and press the ENTER button.

2. Use the CURSOR or button to select your

desired mode and press the ENTER button.

[

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Display Control

Enables you to fine tune the computer image or to remove any

vertical banding that might appear by adjusting the clock frequen-

cies, and to adjust the clock phase or to reduce video noise, dot

interference or cross talk. This also allows you to pan or zoom in/out

the image.

-Display Control-

1. Pixel Clock

2. Pixel Phase

3. Zoom/Pan

Use the CURSOR

button to select the item you want and

press the ENTER button.

Items to select

• Pixel Clock -------- Adjusts the clock frequencies to remove moire.

• Pixel Phase ------- Adjusts the clock phase to reduce video noise.

• Zoom/Pan--------- Magnifies or reduces the image. You also can

pans the display when pressin with CTL.

■ Pixel Clock / Pixel Phase

D i s p l a y C o n t r o l

P i x e l C l o c k

The CURSOR

button increases video noise.

The CURSOR

button decreases video noise.

1 0 2 4

D i s p l a y C o n t r o l

P i x e l P h a s e

3 2

■ Zoom/Pan

The CURSOR

image.

D i s p l a y C o n t r o l

Z o o m

or button enlarges the image or reduces the

The CURSOR

image.

button enlarges the image or reduces the

button pans the image.

CTL+

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Image Control

Enables you to adjust the image position and blanking.

Use the CURSOR

button to select the item you want to

-Image Control-

1. Image Position

2. Blanking

adjust and press the ENTER button.

Items to select

• Image Position ----------- Adjusts the image position.

• Blanking------------------- Adjusts the screen area.

■ Image Position

Pressing the CURSOR

I m a g e C o n t r o l

I m a g e P o s i t i o n

moves the position of the picture

left or right.

Pressing the CURSOR

up or down.

( H )

( V )

2 0 4 8

■ Blanking

Press any one of the CURSOR buttons while press and hold CTL

I m a g e C o n t r o l

to select the position you want to adjust:

B l a n k i n g

S c r e e n

B o t t o m

CTL+

----------- Top

----------- Right

----------- Left

----------- Bottom

2 0 4 8

Top and right -------- Pressing

increases the adjustment

decreases the adjustment

increases the adjustment

decreases the adjustment

values.

Pressing

values.

Bottom and left ----- Pressing

values.

Pressing

values.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Sound Control (only when used with the ISS-6020/ISS-6020G Switcher)

Provides access to control for your sound volume.

S o u n d C o n t r o l

V o l u m e

NOTE: This function works only with the ISS-6020/ISS-6020G

Switcher.

The CURSOR or button increases the volume.

The CURSOR or button decreases the volume.

Closed Caption

Enables you to set several closed caption modes for text to be superim-

posed on the projection screen.

C l o s e d C a p t i o n

Use the CURSOR or button to select the desired mode and

press the ENTER button.

O f f

C a p t i o n

T e x t

Items to select

• Caption 1-4 ------- Text is superimposed.

• Text 1-4 -----------Text is displayed in full screen.

• Off -----------------Exits the selected Closed Caption mode.

NOTE:

• The Closed Caption feature work with an NTSC 3.58 source only.

• Pressing ENTER executes store function. Switching to source

other than NTSC3.58 source again.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Timer Setting

Enables you to program to turn on or off your projector automati-

cally at a specified time. The two timer functions are available: On/

Off Timer and Sleep Timer.

NOTE: When the On Timer is set and the projector is in standby, the

two digit indicator flashes "00" to indicate that the On Timer is

active.

Proceed as follows:

• Before setting On/Off Timer, maker sure that Date, Time Preset

feature is set.

• Even after setting On/Off Timer, turning the projector on or off

with the remote control is possible.

• There are two time display formats: 24-hour or AM/PM format.

You can set either format in the "Date, Time Preset" in [Adjust -

Set Option - Menu Mode].

User the CURSOR

"Sleep Timer".

button to select "On/Off Timer" or

Items to select

• On/Off Timer---Programs to turn on or off the power at a prede-

termined time.

• Sleep Timer---Programs to turn off the power at a predetermined

time, up to two hours later in 30-minute increments.

-Timer Setting-

1. On/Off Timer

2. Sleep Timer

To set the On/Off Timer:

1) Use the CURSOR

button to select On/Off Timer and

O n / O f f T i m e r

press ENTER to display the On/Off Timer menu.

P r g

W e e k

D a y

M o n

O n T i m e

O f f T i m e

1 2 : 0 0

1 W e e k

0 9 : 0 0

E v e r y

M o n - F r i

1 8 : 0 0

2 2 : 0 0

E x e c u t e S w i t c h

[ I n a c t i v e

]

2) Select a program number and press ENTER to display the On/Off

Timer Setting menu.

O n - O f f T i m e r

D A Y O N T I M E

P r g

W e e K

O F F T i m e

1 2 : 0 0 a m

O n / O f f T i m e r S e t t i n g

1 W e E K

M O N

0 9 : 0 0 A M

P r o g r a m

W e e K

[ 1 W e e k

1 8 : 0 0

[ M o n

2]2 : 0 0

]

E v e R Y

M O N - F R I

D a y

O n T i m e

3) Set the Week, Day, On-Time and Off-Time using the CURSOR

buttons and INPUT buttons (1 thru 10). To cancel the on-time or

off time, press NORMAL.

[ 0 0 : 0 0 ]

O f f T i m e

E x e c u t e S W I T C H

[ 0 0 : 0 0 ]

[ I N A C T I V E

]

E n t r y C a n c e l

C l e a r

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

4) Select the Entry and press ENTER. This enables the On Timer or

Off Timer function.

To cancel your data such as week, day, on/off time, select the Cancel

and press ENTER.

To delete the setting data such as week, day and on/off time for the

program number, select the Clear and press ENTER.

NOTE:

When setting On Timer during cooling the fan, the projector will

turn on after the cooling has finished.

To set the Sleep Timer:

1) Use the CURSOR

button to select the Sleep Timer and

press ENTER to display the Sleep Timer menu.

S l e e p T i m e r

T i m e L e f t 1 : 2 3

S e t

2) Select the Set and press ENTER to drop the pull-down menu.

S l e e p T i m e r

3) Select your desired time between 30 minutes and 2 hours in 30

minutes.

S e t T i m e [ 0 : 3 0

]

S E T

0 : 3 0

1 : 0 0

1 : 3 0

2 : 0 0

NOTE: "-- : -- -- " indicates the Sleep Timer will not be used.

O n / O f f T i m e r

D a y O n T i m e

P r g

W e e k

O f f T i m e

1 2 : 0 0

1 W e e k

M o n

0 9 : 0 0

To enable your settings:

E v e r y

M o n - F r i

1 8 : 0 0

2 2 : 0 0

Select "Active" in Execute Switch and press ENTER.

E x e c u t e S w i t c h

[ I n a c t i v e

]

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Adjusting and Setting (Adjustment)

Source Registry

On Source Registry

The projector uses a micro-processor to automatically read and

distinguish between all video signals input at the same time. These

signals are then used to make optimum adjustments for best image.

Various parameters must be registered into the micro-processor

beforehand to ensure the video signals are recognized and adjusted to

optimum quality.

This function registers these video signals in the Source Select list

and at the same time obtains the various parameters pertaining to

these signals. Always access this mode first whenever inputting

video signals for the first time so that you can register

the video signals before making any adjustments. If the current input

signal(s) has not been registered, the “New Signal” message is

displayed on screen.

NOTE: If you have software which changes scanning mode due to

the graphic board of your PC (such as VGA), it will be necessary to

using your PC by way of stopping the software in each scanning

mode and performing a signal entry operation.

■ Source Registry

When connecting a signal for the first time, you need to register it

into the projector’ s memory. You can copy the initial setting for the

new signal from any other signal that has already been registered or

use the factory preset setting.

-Adjustment-

1. Source Registry

2. Amplitude

3. White Balance

4. Signal Level

5. Uniformity

6. Display Function

7. Lamp Mode

8. Set Option

To make the signal entry, proceed as follows:

1 Press the ADJUST button.

• The Adjust menu is displayed.

2 Use the CURSOR

button to highlight the “1.Source

Registry” line and press ENTER.

• The Source Registry menu will be displayed.

• You can also select the Source Registry menu directly by

pressing the INPUT “1” button.

-Source Registry-

1. New Registry

2. Registry Edit

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Items to select

• New Entry ----- Registers a new signal.

• Registry Edit. - Changes setting various parameters of the

registered signals.

3Use the CURSOR

button to highlight the “1.New

Registry” line and press ENTER.

• The “1. Slot” menu is displayed. Then proceed as follows:

1. Select slot.

2. Select signal system.

3. Set HDTV or not when selecting component signal.

4. Input a user name.

5. Select a location number for your registry.

To advance the next item, select Next

and press ENTER. To

return the previous item, select

Prev and press ENTER. To

cancel your registry, select Cancel.

1) To Select a Slot

S o u r c e R e g i s t r y

1 . S l o t

You have two steps depending on whether you use your

projector on standalone or with the ISS-6020 switcher(s).

1 . S l o t

2 . S i g n a l

3 . H D T V

S e l e c t S l o t

I N P U T

NOTE: The setting INPUT TERMINAL cannot be done to the

4 . U s e r N a m e

5 . N o .

current projected signal.

When using the projector in stand alone application:

< P r e v

N e x t >

C a n c e l

Use the CURSOR

button to select one of the three

slots, and press ENTER.

Items to select

• INPUT A ---- Standard

• INPUT B ---- Optional board

• INPUT C ---- Optional board

S o u r c e R e g i s t r y

1 . S l o t

When using with a single Switcher ISS-6020/ISS-6020G:

1 . S l o t

S e l e c t S l o t

Use the CURSOR

button to select the input slot

2 . S i g n a l

3 . H D T V

4 . U s e r N a m e

5 . N o .

M a s t e r

[ S l o t 1

S l a v e

[ S l o t 1

]

number of the Switcher and press ENTER.

• Input slot numbers are from 1 through 10.

• The “4. User Name” screen will be displayed when you finish

entering the slot number.

< P r e v

N e x t >

C a n c e l

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

When using with two or more ISS-6020/ISS-6020G switchers:

Use the CURSOR or button to select the input slot number of

the master Switcher and press ENTER. Then select the slot

number of the slave Switcher and press ENTER.

• The “MASTER” menu will be displayed when the slot

number of the master Switcher is selected.

• The “SLAVE” menu will be displayed when the slot number

of the slave Switcher is selected.

• The “4. User Name” screen will be displayed when you finish

entering the slot number.

2) To Select Signal System

Select your desired signal system.

S o u r c e R e g i s t r y

2 . S i g n a l S y s t e m

Items to select

• RGB ----------- Selects the RGB input signal of this

1 . I N P U T

2 . S i g n a l

3 . H D T V

4 . U s e r N a m e

5 . N o .

S e l e c t S i g n a l S y s t e m

R G B

C - V i d e o

S - V i d e o

C O M P O N E N T

projector

• C-Video ------- Selects the VIDEO input signal of this

projector

< P r e v

N e x t >

C a n c e l

• S-Video ------- Selects the S-VIDEO input signal of this

projector.

• COMPONENT Selects the component input signal of this

projector.

3) To Set HDTV or not When Selecting Component Signal.

When you select COMPONENT, you are asked if the compo-

nent is HDTV or not.

S o u r c e R e g i s t r y

3 . H D T V

1 . I N P U T

I s S i g n a l H D T V ?

Select Yes or No according to your component source.

2 . C O M P O N E N T

3 . H D T V

4 . U s e r N a m e

5 . N o .

Y e s

N o

< P r e v

N e x t >

C a n c e l

S o u r c e R e g i s t r y

4) To Input a User Name.

4 . U s e r N a m e

Input the source name by selecting one character at a time with

the INPUT buttons 1 through 10 and by moving the cursor with

the CURSOR button. After finishing the selection of the

characters, press ENTER.

1 . I N P U T

I n p u t U s e r N a m e

2 . C O M P O N E N T

3 . H D T V M o d e

4 . U s e r N a m e

5 . N o .

[

]

• Up to eight characters can be selected.

< P r e v

N e x t >

C a n c e l

• Eight characters are assigned to one INPUT button.

• Whenever the INPUT button is pressed, characters will be

rotated.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

For example: A → B → C →1 → A .....

• When pressing the INPUT button while holding down the

CTL button, another group of characters will be rotated.

For example: a → b → c → ! → a .....

• The characters corresponding to these INPUT buttons are as

follows:

When using With CTL

INPUT 1 A, B, C, and 1 a, b, c, and !

INPUT 2 D, E, F, and 2 d, e, f, and “\par INPUT 3 G, H, I, and

3 g, h, i, and #

INPUT 4 J, K, L, and 4 j, k, l, and $

INPUT 5 M, N, O, and 5 m, n, o, and %

INPUT 6 P, Q, R, and 6 p, q, r, and &

INPUT 7 S, T, U, and 7 s, t, u, and ‘\par INPUT 8 V, W, X,

and 8 v, w, x, and (

INPUT 9 Y, Z, ?, and 9 y, z, /, and )

INPUT 10 *, ,, ., and 0 ;, :, +, and -

If you have made an error in the input of a character, use the

CURSOR button and enter the correct letter or number.

To delete one character, move the CURSOR button to the

character to be deleted and then press the NORMAL button.

To delete all the entered name, hold down the CTL button then

press NORMAL.

5) To Select a Registry Number.

S o u r c e R e g i s t r y

5 . S e l e c t R e g i s t r y N o .

Select the number location where you want to register the

signal and press ENTER.

O p t i o n

S o u r c e

I n p u t

N o N a m e

0 1

0 2 N T S C

0 3 7 8 K

0 4

0 5 N T S C

0 6 N o 4 0

0 7 N o 3 9

0 8 3 1 . 4 5 K

V I D E O

R G B

The “Do you want to register ?” message is displayed. If yes,

press ENTER.

V I D E O

R G B

V I D E O

0 9

1 0

< P r e v

N e x t >

C a n c e l

S o u r c e R e g i s t r y

D o y o u w a n t t o r e g i s t e r ?

1 . I N P U T

2 . C O M P O N E N T

3 . H D T V M o d e

4 . A B C

Y e s

N o

5 . N o .

< P r e v

N e x t >

C a n c e l

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Registry Edit

This feature allows you to change various parameters of the

source on the selected line. This can be done to the current

projected signal as well as not projected source.

To edit the registered signal, proceed as follows:

1) Press the ADJUST button.

• The Adjust menu is displayed.

2) Use the CURSOR

button to highlight the “1.Source

Registry” line and press ENTER.

• The Source Registry menu will be displayed.

• You can also select the Source Registry menu directly by

pressing the INPUT “1” button.

Items to select

• New Entry------------ Registers a new signal.

• Registry Edit--------- Changes setting various parameters

of the registered signals.

3) Use the CURSOR

Edit” line and press ENTER.

• The “Registry Edit” screen is displayed.

4) Use the CURSOR or button to highlight the registered

signal and press ENTER.

button to highlight the “2. Registry

• The “Edit Command” menu is displayed. Then proceed as

follows:

* Cut Enables you to remove a selected signal from the list

and place it on the “clipboard” in the projector.

* Copy Enables you to copy a selected signal from the list and

place it on the “clipboard” in the projector.

Edit Command

Cut

* Paste Enables you to paste the signal placed on the “clip-

board” to any other line of the list. To do this, select “Paste”

and then select the line number you want to paste to. Last

press ENTER.

Copy

Paste

Information

* Information Enables you to set a various parameters. When

“Information is selected, the Source Information screen is

displayed. Select an item and press ENTER.

5) When setting is completed, press END.

NOE: The contents will leave the “clipboard” when you press

END.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Amplitude

Enables you to adjust the horizontal and vertical amplitude of the

image.

A m p l i t u d e

- A m p l i t u d e -

NOTE: Normally use the normal value.

Use the CURSOR

to adjust the horizontal amplitude.

to adjust the vertical amplitude.

( H )

( V )

When the amplitude adjusting is completed, press the END button.

White Balance

Enables you to adjust the white balance of the image.

W h i t e B a l a n c e

W h i t e / B l a c k L e v e l

Items to select

•White/Red-Blue ----------Adjust the white level for the red or blue.

•Black/Red-Blue ----------Adjust the black level for the red or blue.

Use the CURSOR

to adjust the level of each item.

to select an item.

R e d

B l u e

W h i t e

B l a c k

2 5 5

6 4

1 2 8

When the white balance adjusting is completed, press the END

button.

Signal Level

Enables you to adjust the signal level.

S i g n a l L e v e l

R G B

NOTE: You can directly access the Signal Level by pressing the

SIGNAL LEVEL button on the remote control.

Use the CURSOR

to adjust the level of each item.

to select an item.

R e d

G r e e n

B l u e

6 4

W h i t e

When the signal level adjusting is completed, press the END button.

S i g n a l L e v e l

C O M P O N E N T

G a i n

6 4

C b G a i n

C r G a i n

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Uniformity

Enables you to adjust the white uniformity and edge blending.

The white uniformity feature allows you to adjust color balance on

the left and right side of the screen; the edge-blending feature allows

you to adjust the brightness on the area which two images projected

from the two projectors are overlapped.

-Uniformity-

1. White Uniformity

2. Edge Blending

To Adjust White Uniformity

1) Press R or B button while pressing and holding CTL to select

the color you want to adjust. Note that Green is not available.

2) Move the cursor to the area you want to adjust using CURSOR

button while pressing and holding CTL.

W h i t e U n i f o r m i t y

R e d

S c r e e n

L e f t , T o p

• CTL +

moves the cursor to the right.

moves the cursor to the left.

moves the cursor up.

moves the cursor down.

3) Use the CURSOR buttons to adjust the white uniformity.

• Pressing

increases the level.

decreases the level.

4) Repeat from the step 1 for the other color.

To Adjust the Edge Blending

1) Press the CURSOR buttons while pressing and holding CTL to

select the area you want to adjust.

U n i f o r m i t y

• CTL +

selects the top

selects the bottom

selects the right

selects the left

E d g e B l e n d i n g

S c r e e n

T o p

2) Use the CURSOR

“POS.”.

button to select “DATA” or

D a t a

P o s .

• “DATA” ------- Adjusts the level

• “POS.” --------- Adjusts the position

3) Use the CURSOR

button to adjust the edge blending.

• When “DATA” is selected:

Pressing

increases the level.

decreases the level.

• When “POS.” is selected:

Pressing

moves the position to the top or the right.

moves the position to the bottom or the left.

To exit the Uniformity, press END.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Display Function

Enables you to adjust various items such as the field handling,

interlace mode and sync protect if the image is not displayed

correctly. Normally you do not need to set these items.

-Display Function-

1. Field Handling

2. Interlace Mode

3. Sync Protect

Items to select

• Field Handling -------- Sets the high refresh signal or interlace or

both

• Interlace Mode ------- Selects the interlace mode.

• Sync Protect ---------- Adjusts bending on the top of the screen.

1) Field Handling

Items to select

• None. ----------------- Normally select this mode.

• Frame Drop (FD)----- Select this mode for a high refresh signal.

• Field Jam (FJ)-------- Select this mode for an interlace signal.

• FJ & FD --------------- Select this mode for a high refresh interlace

signal.

F i e l d H a n d l i n g

N o n e .

F r a m e D r o p ( F D )

F i e l d J a m ( F J )

F J

F D

2) Interlace Mode

Select the appropriate mode for an interlace signal viewing the

image. Normally select the mode preset at the factory.

I n t e r l a c e M o d e

N o n S t d :

O d d

O d d + 1

O d d

O d d + 1

S t d

3) Sync Protect

After selecting ON, adjust the bending of the top of the screen.

Normally select OFF.

D i s p l a y F u n c t i o n

S y n c P r o t e c t

To adjust, use the CURSOR

the screen.

to adjust the level viewing

To switch the top or the bottom, press the CURSOR

button.

S y n c P r o t e c t S w i t c h

[ O f f

]

( U )

( D )

1 0 2 4

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Lamp Mode

Enables you to adjust the brightness of the lamp.

Items to select

• Normal ---------------- Normally select this mode.

• High Bright ----------- Select this mode to increase the brightness

of the lamp.

L a m p P o w e r

N o r m a l

H i g h - B r i g h t

NOTE: The High Bright mode shortens the lamp life. Be sure to use

this mode at temperature 95 degrees F (35 degrees C) or less.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Set Option

Passcode

■ Entering Passcode

To prevent any unauthorized operation or mis-adjustment, the

projector is equipped with a passcode option. If your passcode has

not been entered correctly, the “Adjustment” menu will not be

displayed. When the ADJUST button is pressed, and no passcode has

been entered, the “Passcode?” screen is displayed. Enter your

passcode.

To do this, proceed as follows:

1 Press the ADJUST button.

• The “Passcode?” screen is displayed.

2 Enter the four digit passcode you have already registered by

using the “1” through “10” buttons.

^{P a}∗^{s s}∗^c∗^o∗^{d e ?}

1) Each time you press the INPUT button, an asterisk appears

under the “Passcode?” message.

2) After you have finished entering the four digit passcode, press

ENTER.

NOTE: If you have made an error, press the NORMAL button to

delete the asterisk “*”. Then re-enter the correct passcode. To

delete all the entered digits, hold down the CTL button then

press the NORMAL button.

3) If the entered passcode is correct, the “ADJUST” menu is

displayed.

NOTE: If the passcode is not correct, the “Warning Different

Passcode!!” message is displayed and you are required to enter

the correct passcode.

3 Proceed to each adjustment and setting.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Registering Passcode

When the projector is shipped from the factory, no passcode is

registered. If you want to use the passcode option, you must register

a passcode.

-Adjustment-

1. Source Registry

2. Amplitude

To register a new passcode, proceed as follows:

1 Press the ADJUST button.

• The “Adjustment” menu will be displayed.

3. White Balance

4. Signal Level

5. Uniformity

6. Display Function

7. Lamp Mode

8. Set Option

2 Use the CURSOR

button to highlight the “8.Set Option”

-Set Option-

1. Passcode

menu. Press ENTER to display the Set Option menu.

2. Setting Mode

3. Menu Mode

4. Execute Mode

3 Use the CURSOR

button to highlight the “1.Passcode”

line. Press ENTER to display the “Passcode Setting” menu.

4 Use the CURSOR

button to select “Entry”. Press

ENTER to display the “New Passcode?” menu.

P a s s c o d e

P a s s c o d e S e t t i n g

E n t r y

D i s a b l e

5 Enter a four digit passcode using the “1” through “10” buttons.

1) Each time you press the INPUT button, an asterisk will appear

next to the “New Passcode?” message.

NOTE: “0000” and “9999” cannot be used as a passcode.

P a s s c o d e

P A S S C O D E S E T T I N G

P a s s c o d e S e t t i n g

E N A B L E D I S A B L E

2) Once you have finished entering your four digit passcode,

press ENTER to store the code.

N e w P a s s c o d e

[

]

✳ ✳ ✳ ✳

NOTE: If you have made an error, press the NORMAL button

to delete the asterisk “✻”. Then re-enter the correct passcode.

To delete all the entered digits, hold down the CTL button

then press the NORMAL button.

3) If the passcode has been entered correctly, the “Confirm New

Passcode?” menu will be displayed.

NOTE: If the passcode is not entered correctly, the “Warning

Passcode!!” message will be displayed. You will be required

to enter the passcode correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

6 Enter the new passcode again.

1) Each time you press the INPUT button, an asterisk will appear

next to the “Confirm New Passcode?” message.

2) Once you have finished entering the new four digit passcode,

press ENTER.

NOTE: If you have made an error, press the NORMAL button

to delete the asterisk “*”. Then re-enter the correct passcode.

To delete all the entered digits, hold down the CTL button

then press the NORMAL button.

3) If the entered passcode is correct, the “Change Passcode

Complete!!” message will be displayed.

P a s s c o d e

P A S S C O D E S E T T I N G

P a s s c o d e S e t t i n g

NOTE: If the passcode is not correct, the “Warning Different

Passcode!!”message will be displayed. You are required to

enter the new passcode correctly.

E N A B L E

D I S A B L E

C o n f i r m P a s s c o d e

[

]

✳ ✳ ✳ ✳

The new passcode has been registered.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Changing Your Passcode

To change your passcode, proceed as follows:

1 Press the ADJUST button.

• The “Passcode?” screen will be displayed.

-Adjustment-

1. Source Registry

2. Amplitude

3. White Balance

4. Signal Level

5. Uniformity

2 Enter the four digit current passcode using the “1” through “10”

buttons. Press ENTER.

• The “Adjustment” menu will be displayed.

6. Display Function

7. Lamp Mode

8. Set Option

-Set Option-

1. Passcode

2. Setting Mode

3. Menu Mode

4. Execute Mode

3 Use the CURSOR

button to highlight the “8. Set

Option” menu. Press ENTER to display the “Set Option” menu.

4 Use the CURSOR

button to select “1. Passcode”. Press

ENTER to display the “Passcode Setting” menu.

P a s s c o d e

5 Use the CURSOR

button to select “Entry”.

P a s s c o d e S e t t i n g

PressENTER to display the “Current Passcode?” menu.

E n t r y

D i s a b l e

6 Enter the four digit passcode (the current passcode) using the “1”

through “10” buttons.

1) Each time you press the INPUT button, an asterisk will

appear next to the “Current Passcode?” message.

2) Once you have finished entering the four digit passcode, press

ENTER.

P a s s c o d e

P a s s c o d e S e t t i n g

C u r r e n t P a s s c o d e

[

]

✳ ✳ ✳ ✳

NOTE: If you have made an error, press the NORMAL button

todelete the asterisk “*”. Then re-enter the correct passcode.

To delete all the entered digits, hold down the CTL button

then press the NORMAL button.

3) If the entered passcode is correct, the “New Passcode?”

screen will be displayed.

P a s s c o d e

P A S S C O D E S E T T I N G

P a s s c o d e S e t t i n g

E N A B L E D I S A B L E

NOTE: If the passcode is not correct, the “Warning

Different Passcode!!” message is displayed. You will be

required to enter the correct current passcode.

N e w P a s s c o d e

[

]

✳ ✳ ✳ ✳

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

7 Enter a new passcode using the “1” through “10” buttons.

1) Each time you press the INPUT button, an asterisk will appear

next to the “New Passcode?” message.

2) Once you have finished entering the four digit new passcode,

press ENTER.

NOTE: If you have made an error, press the NORMAL button

to delete the asterisk “*”. Then re-enter the correct passcode.

To delete all the entered digits, hold down the CTL button

thenpress the NORMAL button.

3) If the passcode has been entered correctly, the “Confirm New

Passcode?” menu will be displayed.

NOTE: If the passcode is not entered correctly, the “Warning

Different Passcode!!” message will be displayed. You are

required to enter the new passcode correctly.

P a s s c o d e

P A S S C O D E S E T T I N G

P a s s c o d e S e t t i n g

E N A B L E

D I S A B L E

C o n f i r m P a s s c o d e

[

]

✳ ✳ ✳ ✳

8 Enter the new passcode again using the “1” through “10” buttons.

1) Each time you press the INPUT button, an asterisk will appear

under the “Confirm New Passcode?” message.

2) Once you have finished entering the four digit new passcode,

press ENTER.

NOTE: If you have made an error, press the NORMAL button

to delete the asterisk “*”. Then re-enter the correct passcode.

To delete all the entered digits, hold down the CTL button

then press the NORMAL button.

3) If the entered passcode is correct, the “Change Passcode

Complete!!” message is displayed.

NOTE: If the passcode is not entered correctly, the “Warning

Different Passcode!!” message is displayed. You will be

required to enter the new passcode correctly.

The passcode has been changed to another.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Canceling Your Passcode

To cancel the passcode, proceed as follows:

1 Press the ADJUST button and then enter your passcode.

• The “Passcode?” screen will be displayed.

2 Enter the four digit current passcode using the “1” through “10”

buttons and then press ENTER.

-Adjustment-

1. Source Registry

2. Amplitude

3. White Balance

4. Signal Level

5. Uniformity

• The “Adjustment” menu will be displayed.

6. Display Function

7. Lamp Mode

8. Set Option

3 Use the CURSOR

button to highlight “8. Set Option”.

Press the ENTER button to display the “Set Option” menu.

-Set Option-

1. Passcode

2. Setting Mode

3. Menu Mode

4. Execute Mode

4 Use the CURSOR

button to highlight “1. Passcode”

line. Press ENTER to display the “Passcode Setting” menu.

P a s s c o d e

P a s s c o d e S e t t i n g

5 Use the CURSOR

button to select “Disable”. Press

E n t r y

D i s a b l e

ENTER to display the “Passcode Disable?” menu. Select “Yes”

and press ENTER.

• The “Current Passcode” screen will be displayed.

6 Enter the four digit passcode (the current passcode) using the “1”

through “10” buttons.

P a s s c o d e

P a s s c o d e S e t t i n g

C u r r e n t P a s s c o d e

1) Each time you press the INPUT button, an asterisk will appear

next to the “Current Passcode?” message.

2) Once you have finished entering the four digit passcode, press

ENTER.

[

]

✳ ✳ ✳ ✳

NOTE: If you have made an error, press the NORMAL button

to delete the asterisk “*”. Then re-enter the correct passcode.

To delete all the entered digits, hold down the CTL button

then press the NORMAL button.

3) If the entered passcode is correct, the “Passcode Disable?”

menu will be displayed.

P a s s c o d e

P A S S C O D E S E T T I N G

P a s s c o d e S e t t i n g

E N A B L E D I S A B L E

P a s s c o d e D i s a b l e

NOTE: If the passcode is not correct, the “Warning Different

Passcode!!” message will be displayed. You will be required

to enter your correct passcode.

Y e s

N o

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

7 Use the CURSOR

button to select Yes and then press

ENTER.

Items to select

• Yes ---------------- When selecting “Yes”, the current passcode

will be canceled. You will not be required to

re-enter your passcode when you press the

ADJUST button to re-enter the ADJUST

mode.

• No ----------------- When selecting “No”, the current passcode

will remain in effect.

Your passcode has been cancelled.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Setting Mode

Enables you to set various items.

To do, follow the steps below.

1. Press the ADJUST button to display the Adjustment menu.

2. Use the CURSOR

Press ENTER.

button to select “8. Set Option” menu.

3. Use the CURSOR

menu. Press ENTER.

button to select “2. Setting Mode”

Proceed to the following steps.

■ PJ Orientation

-Setting Mode-

1. PJ Orientation

This feature allows you to set the installation type according to the

projection configuration.

2. Default Source Select

3. S-Video Mode Select

4. Video System Select

5. Auto Data Store

6. Option Terminal Speed

7. Uniformity Switching

1 Use the CURSOR or button to select the “PJ ORIENTA-

TION” item, then press ENTER to display the “PJ ORIENTA-

TION” menu.

P J O r i e n t a t i o n

[ C e i l i n g / F r o n t

]

D e f a u l t M o d e S e l e c t

D e f a u l t

I N P U T - A

S - V i d e o

[ S 2

]

S - V i d e o M o d e S e l e c t

V i d e o S y s t e m S e l e c t

M a n u a l

N T S C 3 . 5 8

A u t o D a t a S t o r e

[ D i s a b l e

O p t i o n T e r m i n a l S p e e d

[ 3 8 4 0 0 B P S

[ D i s a b l e

]

U n i f o r m i t y W h i t e

E d g e B l e n d .

[ D i s a b l e

2 Use the CURSOR or button to select one of the four

projector installation types and press ENTER.

Floor / Rear

Items to select

Ceiling / Front

Floor / Front

Ceiling / Rear

• CEILING/REAR .... Ceiling mounting type and rear projection

• FLOOR/REAR....... Desk top type and rear projection

• CEILING/FRONT .. Ceiling mounting type and front projection

• FLOOR/FRONT..... Desk top type and front projection

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Default Source Select

You can set the projector to default to any one of its inputs each time

the projector is turned on.

Proceed as follows:

-Setting Mode-

1. PJ Orientation

2. Default Source Select

3. S-Video Mode Select

4. Video System Select

5. Auto Data Store

1 Use the CURSOR or button to select the “Default Source

Select” item, then press ENTER to display the “Default Source

Select” menu.

6. Option Terminal Speed

7. Uniformity Switching

P J O r i e n t a t i o n

[ C e i l i n g / F r o n t

]

D e f a u l t M o d e S e l e c t

D e f a u l t

I N P U T - A

S - V i d e o

[ S 2

]

S - V i d e o M o d e S e l e c t

V i d e o S y s t e m S e l e c t

M a n u a l

N T S C 3 . 5 8

A u t o D a t a S t o r e

[ D i s a b l e

O p t i o n T e r m i n a l S p e e d

[ 3 8 4 0 0 B P S

[ D i s a b l e

]

U n i f o r m i t y W h i t e

E d g e B l e n d .

[ D i s a b l e

2 Use the CURSOR or button to select either “Default” or

“Last” and press ENTER.

P j O R I E N T A T I O N

[ C E I L I N G / F R O N T

]

• Selecting “LAST” completes setting.

D e f a u l t S o u r c e S e l e c t

D E F A U L T

I N P U T - A

D e f a u l t U L T M O D E S E L E C T

• Selecting “DEFAULT” displays the “Default input” screen.

D e f a u l t

S o u r c e

S l o t

[ D e f a u l t

]

S - V I D E O

[ I n p u t - A

]

S i g n a l

[ C O M P O . H D T V )

]

[ ? ? ? ? ? ? ? ? ? C D )

S - V I D E O M O D E S E L E C T

Items to select

O K

C a n c e l

M A N U A L

V i d E O S Y S T E M S E L E C T

N T S C 3 . 5 8

• DEFAULT . Displays the same source input every time the

projector is started up.

[ D e f a u l t

]

A u t o D a t a S t o r e

[ 3 8 4 0 0 B p s

]

O p t i o n T e r m i n a l S p e e d

• LAST ....... Sets the projector to default to the previous last

active input each time the projector is turned on.

Note: An input must be active for a minimum of 10

minutes before it is recognized as the last active

signal.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

3 Use the CURSOR or button to select an input and

then press the ENTER button.

When used in stand alone operation:

The default input screen will be displayed.

Use the CURSOR or button to select an input and

press ENTER.

I N P U T

When used with a single Switcher:

M A S T E R

S L O T – 0 1

S L O T – 0 2

S L O T – 0 3

S L O T – 0 4

S L O T – 0 5

S L O T – 0 6

S L O T – 0 7

S L O T – 0 8

S L O T – 0 9

S L O T – 1 0

The “MASTER” slot menu will be displayed.

Use the CURSOR or button to select the desired slot

number “1” through “10(0)” and then press ENTER.

When used with two or more Switchers:

The “MASTER” and “SLAVE” slot number menu will be

displayed.

M A S T E R

S L O T – 0 1

S L O T – 0 2

S L O T – 0 3

S L O T – 0 4

S L O T – 0 5

S L O T – 0 6

S L O T – 0 7

S L O T – 0 8

S L O T – 0 9

S L O T – 1 0

S L A V E

S L O T – 0 1

S L O T – 0 2

S L O T – 0 3

S L O T – 0 4

S L O T – 0 5

S L O T – 0 6

S L O T – 0 7

S L O T – 0 8

S L O T – 0 9

S L O T – 1 0

Use the CURSOR or button to select the master slot

number first and then select the slave slot number “1”

through “10(0)”. Press ENTER.

4 Use the CURSOR or button to select a signal and

press ENTER button.

R G B

V I D E O

S - V I D E O

C O M P O N E N T

5 Press OK to complete the setting.

C O M P O . ( H D T V )

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ S-Video Mode Select

]

-Setting Mode-

This function is used to select the S-video signal detection mode.

This allows identifying of the S-video signals with different aspect

ratio: squeeze or full mode(16 : 9) and letter box (4 : 3) signals.

To set, proceed as follows:

1. PJ Orientation

2. Default Source Select

3. S-Video Mode Select

4. Video System Select

5. Auto Data Store

6. Option Terminal Speed

7. Uniformity Switching

1 Use the CURSOR or button to select the “S-Video Mode

Select” item, then press ENTER to display the “S-Video Mode

Select” menu.

P J O r i e n t a t i o n

[ C e i l i n g / F r o n t

]

D e f a u l t M o d e S e l e c t

D e f a u l t

I N P U T - A

S - V i d e o

[ S 2

]

S - V i d e o M o d e S e l e c t

V i d e o S y s t e m S e l e c t

M a n u a l

N T S C 3 . 5 8

A u t o D a t a S t o r e

[ D i s a b l e

O p t i o n T e r m i n a l S p e e d

[ 3 8 4 0 0 B P S

[ D i s a b l e

]

U n i f o r m i t y W h i t e

E d g e B l e n d .

[ D i s a b l e

2 Use the CURSOR or button to select one of the three items:

S2, S1, and OFF, and then press ENTER.

S-Video Mode Select

Items to select

S 2

S 1

O F F

S2 .............. Identifies squeeze and letter box signals.

S1 .............. Identifies a squeeze signal only.

OFF ............ Does not identify any S-video signal.

NOTE :

• The input signal must be compatible with the S2/S1 MODE

standard.

Refer to the user manual included with the connected equip-

ment for more information.

• The identification function may not work correctly with a non-

compatible signal. If this happens, select “OFF” from the “S-

VIDEO MODE SELECT” menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Video System Select

This function is used to select the NTSC 3.58, NTSC 4.43, PAL or

SECAM video standard.

-Setting Mode-

1. PJ Orientation

2. Default Source Select

3. S-Video Mode Select

4. Video System Select

5. Auto Data Store

6. Option Terminal Speed

7. Uniformity Switching

To select any one of the video standards, proceed as follows:

1 Use the CURSOR or button to select the “Video System

Select ” item, then press ENTER to display the “Video System

Select” menu.

P J O r i e n t a t i o n

[ C e i l i n g / F r o n t

]

D e f a u l t M o d e S e l e c t

D e f a u l t

I N P U T - A

S - V i d e o

[ S 2

S - V i d e o M o d e S e l e c t

V i d e o S y s t e m S e l e c t

M a n u a l

N T S C 3 . 5 8

A u t o D a t a S t o r e

[ D i s a b l e

]

O p t i o n T e r m i n a l S p e e d

[ 3 8 4 0 0 B P S

2 Use the CURSOR or button to select either “Auto” or a

video standard manually and then press ENTER.

P j O r i e n t a t i o n

D e f a u l t M o d e S e l e c t

[ C e i l i n g / F r o n t

D e f a u l t

]

V i d e o S y s t e m S e l e c t

I n p u t - A

When selecting “AUTO”

S - V i d e o

A U T O

N T S C 3 . 5 8

[ ? ? ? ? ? ? ? ? ? ?

S - V i d e o M o d e S e l e c t

N T S C 4 . 4 3

Video Modes

V i d e o S y s t e m S e l e c t

P A L

M a n u a l

N T S C 3 . 5 8

S E C A M

• NTSC3.58 ............ Indicates the NTSC3.58 video standard

• NTSC4.43 ............ Indicates the NTSC4.43 video standard

• PAL ..................... Indicates the PAL video standard

• SECAM ................ Indicates the SECAM video standard

• Select “Auto” in normal operation.

A u t o D a t a S t o r e

O p t i o n T e r m i n a l S p e e d

[ D i s a b l e

]

[ 3 8 4 0 0 B p s

• Select a video standard manually when connecting to poor

quality signal or non-standard signals such as video games.

VIDEO MODE SELECT

N T S C 3 . 5 8

N T S C 4 . 4 3

P A L

NOTE: The projector may not function correctly with a mono-

chrome signals in the Auto mode.

S E C A M

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Auto Data Store

-Setting Mode-

1. PJ Orientation

This feature allows you to select two ways to store settings; auto-

matically and manually.

2. Default Source Select

3. S-Video Mode Select

4. Video System Select

5. Auto Data Store

6. Option Terminal Speed

7. Uniformity Switching

After “Enable” is selected in the Auto Data Store menu, all projector

settings are stored in the projector's memory automatically. To set

this feature, proceed as follows:

1 Use the CURSOR or button to select the “Auto Data Store”

item on Page 2, then press ENTER to display the “Auto Data

Store” menu.

P J O r i e n t a t i o n

[ C e i l i n g / F r o n t

]

D e f a u l t M o d e S e l e c t

D e f a u l t

I N P U T - A

S - V i d e o

[ S 2

]

S - V i d e o M o d e S e l e c t

V i d e o S y s t e m S e l e c t

M a n u a l

N T S C 3 . 5 8

A u t o D a t a S t o r e

[ D i s a b l e

O p t i o n T e r m i n a l S p e e d

[ 3 8 4 0 0 B P S

[ D i s a b l e

]

U n i f o r m i t y W h i t e

E d g e B l e n d .

[ D i s a b l e

2 Use the CURSOR or button to select either “Disable” or

“Enable” and then press ENTER.

Auto Data Store

D i s a b l e

Items to select

E n a b l e

• Disable .... Projector does not store the settings automatically.

• Enable ..... Projector stores the settings automatically.

Automatic storing data is done when any one of the following

procedures is performed:

• Pressing the END button several times returns the adjustment

screen to the source screen.

• One input is switched to another.

• The projector is turned off.

• Every 10 minutes.

NOTE: After “Disable” is selected in the Auto Data Store menu,

the settings will not be stored in the memory unless you select

“Yes” in the “Store ?” menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Option Terminal Speed

This feature allows you to set baud rate of the OPTION terminal

from 4800 to 38400 bps.

NOTE:

• The baud rate of the OPTION terminal defaults to 38400 bps at the

factory.

• Make sure that the baud rate of the OPTION terminal matches that

of operating of the connected equipment.

-Setting Mode-

1. PJ Orientation

To change the baud rate of the OPTION terminal, proceed as follows:

2. Default Source Select

3. S-Video Mode Select

4. Video System Select

5. Auto Data Store

1 Use the CURSOR

button to select the “Option

Terminal Speed” item, then press ENTER to display the “Option

Term Boad Rate” menu.

6. Option Terminal Speed

7. Uniformity Switching

P J O r i e n t a t i o n

[ C e i l i n g / F r o n t

]

D e f a u l t M o d e S e l e c t

D e f a u l t

I N P U T - A

S - V i d e o

2 Use the CURSOR

button to select the baud rate from

4800 to 38400 bps and press ENTER.

[ S 2

]

S - V i d e o M o d e S e l e c t

V i d e o S y s t e m S e l e c t

M a n u a l

N T S C 3 . 5 8

A u t o D a t a S t o r e

[ D i s a b l e

O p t i o n T e r m i n a l S p e e d

[ 3 8 4 0 0 B P S

[ D i s a b l e

]

U n i f o r m i t y W h i t e

E d g e B l e n d .

[ D i s a b l e

4 8 0 0 B P S

9 6 0 0 B P S

1 9 2 0 0 B P S

3 8 4 0 0 B P S

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Uniformity Switching

Enables you to enable or dasable the uniformity white and edge

blending features.

-Setting Mode-

1. PJ Orientation

2. Default Source Select

3. S-Video Mode Select

4. Video System Select

5. Auto Data Store

1 Use the CURSOR

button to select the “Uniformity

Switching” item, then press ENTER.

6. Option Terminal Speed

7. Uniformity Switching

2 Use the CURSOR

button to select the “White Unifor-

mity or Edge Blend.” item, and select Disable or Enable, then

ENTER.

P J O r i e n t a t i o n

[ C e i l i n g / F r o n t

]

D e f a u l t M o d e S e l e c t

D e f a u l t

I N P U T - A

S - V i d e o

[ S 2

]

S - V i d e o M o d e S e l e c t

V i d e o S y s t e m S e l e c t

M a n u a l

N T S C 3 . 5 8

A u t o D a t a S t o r e

[ D i s a b l e

O p t i o n T e r m i n a l S p e e d

[ 3 8 4 0 0 B P S

[ D i s a b l e

]

U n i f o r m i t y W h i t e

E d g e B l e n d .

[ D i s a b l e

D i s a b l e

E n a b l e

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Menu Mode

Enables you to set various items for on-screen display.

To do, follow the steps below.

1. Press the ADJUST button to display the Adjustment menu.

2. Use the CURSOR

Press ENTER.

button to select “8. Set Option” menu.

3. Use the CURSOR

menu. Press ENTER.

button to select “3. Menu Mode”

Proceed to the following steps.

This feature allows you to display the items on the top of the

screen: date, time, input signal, source name, address, and new

signal.

■ Message Time

There are two modes of operations for the on-screen display. With

AUTO mode, the on-screen display will automatically switch off

after three through ten seconds. In the MANUAL mode, the display

must be manually turned off with the DISPLAY button on the full

function remote control each time it appears.

-Menu Mode-

1. Message Time

2. Date, Time Preset

3. Display Item Set

NOTE: Pressing DISPLAY with CTL will select the non on-screen

mode; pressing DISPLAY with CTL again will cancel this mode.

Even if the on-screen display may be turned off with CTL and

DISPLAY, any adjustment will still change the projector’s memory

settings.

Proceed as follows:

1 Use the CURSOR or button to highlight the “Message

Time” item.

M e s s a g e T i m e

[ A u t o 1 0 S e c

]

D a t e , T i m e P r e s e t

D i s p l a y I t e m S e t

J a n / D D / Y Y Y Y

H H : M M : S S

Press ENTER to display the “Message Time” menu.

D a t e

T i m e

[ O f f

]

I n p u t S i g n a l

S o u t c e N a m e

A d d r e s s

[ O f f

N e w S i g n a l

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

2 Use the CURSOR or button to select either “Auto” or

“Manual“ and press ENTER.

Manual

Items to select

Auto 3 sec

Auto 10 sec

Auto 30 sec

• Auto......... The on-screen menu display appears when the

buttons on the remote control, or the controls on

the rear panel are pressed. The on-screen display

will turn off at a preselected time.

The OFF TIME is specified in seconds up to a

maximum of 30 seconds.

Select your desired time (3-30 seconds) from the

OFF TIME menu.

• Manual .... The on-screen menu display appears when the

buttons on the remote control, or the controls on

the rear panel are pressed. The display will be

turned on and off whenever the DISPLAY button is

pressed. If no button operation is made for 20

minutes or more, the on-screen message will

automatically turn off.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Date, Time Preset

The current year, month, date and time are displayed on the top of

-Menu Mode-

the screen.

1. Message Time

2. Date, Time Preset

3. Display Item Set

Proceed as follows:

1 Use the CURSOR or button to highlight the “Date, Time,

Preset” item. Press ENTER to display the “Date, Time Preset”

menu.

M e s s a g e T i m e

[ A u t o 1 0 S e c

]

D a t e , T i m e P r e s e t

D i s p l a y I t e m S e t

J a n / D D / Y Y Y Y

H H : M M : S S

D a t e

T i m e

[ O f f

]

I n p u t S i g n a l

S o u t c e N a m e

A d d r e s s

[ O f f

N e w S i g n a l

2 Use the CURSOR or button to select any one of the two

items: Date, and Time.

M e s s a g e T i m e

[ A u t o 1 0 S e c

]

D a t e , T i m e P r e s e t

J a n / D D / Y Y Y Y

H H : M M : S S

M M / D D / Y Y Y Y

D a t e

D i s p l a y I t e m S e t

[ 1 2 / 1 5 / 1 9 9 7 ] ( M o n )

D a t e

[ O f f

]

T i m e

H H / M M / S S

3 Type the date adn time. Then press OK.

T i m e

[ O f f

[ 2 0 : 3 0 : 0 0 ]

I n p u t S i g n a l

O K

C a n c e l

S o u t c e N a m e

A d d r e s s

N e w S i g n a l

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Display Item Set

This feature allows you to display the items : date, time, input signal,

source name, address, and new signal on the top of the screen.

1 Use the CURSOR or button to highlight the “Display Item

-Menu Mode-

Set” menu. Press ENTER.

1. Message Time

2. Date, Time Preset

3. Display Item Set

2 Use the CURSOR or

buttons to select on or off and press

ENTER.

M e s s a g e T i m e

[ A u t o 1 0 S e c

]

D a t e , T i m e P r e s e t

D i s p l a y I t e m S e t

J a n / D D / Y Y Y Y

H H : M M : S S

D a t e

T i m e

[ O f f

]

I n p u t S i g n a l

S o u t c e N a m e

A d d r e s s

[ O f f

N e w S i g n a l

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Execute Mode

Enables you to select connecting with the switcher ISS-6020 and

view the projector address on the screen.

To do, follow the steps below.

1. Press the ADJUST button to display the Adjustment menu.

2. Use the CURSOR

Press ENTER.

button to select “8. Set Option” menu.

3. Use the CURSOR

menu. Press ENTER.

button to select “4. Execute Mode”

Proceed to the following steps.

■ Connect Condition

This setting explains how the projector is used with the ISS-6020/

ISS-6020G Switcher.

1 Use the CURSOR or button to select the “1. Connect

Condition” item, then press ENTER to display the ““1. Connect

Condition” menu.

-Execute Mode-

1. Connect Condition

2. PJ Address

2 Use the CURSOR or button to select your desired connec-

tion condition of Switcher and press ENTER.

E x c u t e M o d e

• The “Re-Start ?” prompt is displayed after setting of the connec-

tion condition is modified from the current status to your desired

condition.

C o n n e c t C o n d i t i o n

P J A d d r e s s

[ S t a n d A l o n e

[ 0 1 ] ( 0 1 - 6 4 )

]

Items to select

• Stand Alone ......... The projector used in stand alone operation.

• SW 1 Level .......... The projector used with one Switcher.

• SW 2 Level .......... The projector used with two or more

Switchers.

Connect Condition

Stand Alone

SW1 Level

SW2 Level

3 Use the CURSOR or button to select either “Yes” or “No”

and press ENTER.

Items to select

• Yes .......... Restart the projector.

• No ........... Does not restart the projector.

R e - S t a r t ?

Y e s

N o

NOTE: The selected connection condition becomes effective

only after the projector is restarted.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ PJ Address

Each projector needs its own unique address in the case of a serial

connection of projectors. Up to 64 addresses can be set.

Proceed as follows:

1 Use the CURSOR or button to highlight the “2/PJ Address”

line. Press ENTER to display the “Address” menu.

-Execute Mode-

1. Connect Condition

2. PJ Address

2 Enter the address number using the INPUT button and press

ENTER.

E x c u t e M o d e

Execute Mode

• If you have made a mistake, press END to return to the “OP-

TION” menu, then start again.

C o n n e c t C o n d i t i o n

P J A d d r e s s

[ S t a n d A l o n e

[ 0 1 ] ( 0 1 - 6 4 )

]

NOTE: Enter the address number “01” when only one projector

is used.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Ⅵ Addressing the Remote Control Unit

When changing the projector address, ensure that the projector

address respond to the remote control address, otherwise you cannot

operate the projector using the remote control.

To specify the remote control address, proceed as follows:

1) Press and hold the CTL button then press the ADDRESS button

to access the RC UNIT address mode.

ADDRESS

RC UNIT

• The current remote control address is displayed on the remote

control address screen. (When the current remote control

address is configured at "00", the remote control address screen

will not be displayed.

• This screen will disappear in 30 seconds.

∗∗

NOTE: When the remote control is used with the Switcher in

wired application, a window shown on the right will not be

displayed. However, the remote control address can be

changed.

When the remote control address is configured at

"00", the above screen will not be displayed.

2) Use INPUT buttons to enter a new two-digit number and press

ENTER.

• The new remote control address is displayed on the screen.

When the new remote control address is configured at "00", the

display will not be changed. However, its address has been

changed by pressing ENTER.

• The number you can specify ranges from 00 to 64.

To stop the address changing, press END.

See the projector address number on the screen.

NOTE:

• The buttons other than the above mentioned button and the

OFF button are not available during specifying the remote

control address.

• If no key input is made within 30 seconds, the remote control

automatically exits the RC UNIT address mode.

Address common to all the projectors

When specifying the remote control address as “00”, you can

operate the projector using the remote control, regardless of the

projector addresses.

If the remote control loses power, the remote control address

becomes “00”. In this case the on-screen shown on the right

above is not displayed on the screen.

3) To complete, press END.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Help Menu

Provides information about operation and adjustment procedures or

the set information.

-Help-

1. Help

2. Topics

3. Set Information

To view the information:

Press OPERATE or ADJUST button then select “Help” from the

Task bar and press ENTER. The Help menu will be displayed.

■Help

Provides information how to use the Help.

To view the Help menu, use the CURSOR

“1. Help” menu and press ENTER.

button to select

■ Topics

Provides you information of a various items explaining function and

operation.

To view information, use the CURSOR

Topics” menu and press ENTER.

button to select “2.

■ Set Information

Lets you know the version for the running time, the lamp usage time,

the version for your hardware and software.

To view the information, use the CURSOR

“3. Set Information” menu and press ENTER.

button to select

S e t I n f o r m a t i o n

U s e r N a m e

[

]

S e t S e r i a l N o .

S e t H o u r M e t e r

L a m p H o u r M e t e r

S o f t w a r e V e r s i o n

[

0 3 0 0 H

0 1 0 0 H

4 0 M

2 0 M

The information you can view are:

1 . 0 0

B i o s

User Name ------------------- Indicates the user name

A p p l i c a t i o n

D a t a

S u b C P U

S w i t c h e r

Set Serial No. --------------- Indicates serial number for your projec-

tor

1 . 0 0

H a r d w a r e V e r s i o n

Set hour Meter -------------- Indicates the amount of operating time

of your projector

Lamp Hour Mete ----------- Indicates the amount of operating time

of the lamp

Software version ------------ Indicates the version for the software

Hardware version ----------- Indicates the version for the hardware

*The Switcher item is displayed only when the Connect Condition is

set to the SW 1 or 2 Level.

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

Others

■ Test Patterns

This projector will generate a selection of test signals.

Six kinds of internal test patterns can be selected from the Test

Pattern menu.

To display the Test Pattern menu, proceed as follows:

1. Press the TEST button on the remote control.

• The Test Pattern menu will be displayed.

T e s t P a t t e r n

• When END is pressed, the Test Pattern menu will disappear.

O f f

F l a t F i e l d

R a m p

C o n t r a s t C h e c k e r b o a r d

G r i d P a t t e r n

G r a y B a r s

2 User the CURSOR

button to highlight the test pattern

S m a l l C h e c k e r b o a r d

you wish to use and press ENTER.

• The selected test pattern will be displayed.

3 To return to the original screen, press TEST and then press END.

• When the TEST button is pressed, the Test Pattern menu will

be displayed and when END is pressed, the screen will be

changed to the source screen.

• The projector will return to the original source screen by

pressing END only when no menu or no adjustment screen is

displayed.

TEST PATTERN

GRAY BARS

GRID PATTERN

FLAT PATTERN

CONTRAST CHECKER BOARD

SMALL CHECKER BOARD

RAMP

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ Normal, Load, and Cancel Function

Adjustment settings can be returned to the factory preset level,

previously stored level, or can be canceled.

To return to the standard level (Normal):

1. Press the NORMAL button.

T e s t P a t t e r n

The confirmation message is displayed.

2. Use the CURSOR

button to select Yes.

Y e s

N o

A confirmation message is displayed.

3. Press ENTER.

The Normal function is performed.

If you select “No”, you will exit this mode suspending current

status.

■To return to the last stored level (Load):

1. Press and hold the CTL button then press the NORMAL button.

• The Memory menu is displayed.

2. Use the CURSOR

A confirmation message is displayed.

3. Use the CURSOR or button to select Yes.

button to select Load.

M e m o r y

L o a d

C a n c e l

• If you select No, you will exit this mode suspending current

status.

4. Press ENTER.

• The LOAD function is performed.

L o a d

Y e s

N o

Download from Www.Somanuals.com. All Manuals Search And Download.

3.OPERATION

■ To cancel the adjustment data (Cancel):

1. Press and hold the CTL button then press the NORMAL button.

• The Memory menu is displayed.

2. Use the CURSOR

• A confirmation message is displayed.

3. Use the CURSOR or button to select Yes.

button to select Cancel.

M e m o r y

L o a d C a n c e l

• If you select No, you will exit this mode suspending current

status.

4. Press ENTER.

• The CANCEL function is performed.

C a n c e l

Y e s

N o

Download from Www.Somanuals.com. All Manuals Search And Download.

4.SPECIFICATIONS

Projection Type

: 3Chip DMD TM High light out put projector.

Projection System

Display Orientation

: 3chip DMD TM , 1 Lens

: Front Floor , Rear Floor ,

Front Ceiling , Rear Ceiling

: Bulb type 1.6 KW Xenon Lamp

: 0 + 150 pixel by Zoom Lens ( One direction )

0 + 300 pixel by Fixed Lens ( One direction )

: H 15-64KHz

Lamp Type

Shooting offset

Scanning line rat

/ Flame rate

Resolution

V 30-100Hz

: DMD^TM848ϫ600 pixel

Max : 1024 ϫ 768 by Scaling

: Max 80 MHz

Pixel clock

Lens (optional)

: Fixed lens ;

Type 1 : 1.27:1

Type 2 : 3.0:1

Type 3 : 5.0:1

Type 4 : 7.0:1

Zoom Lens

Type 1 : 1.5-3.0

Type 2 : 3.0-7.0

Picture Size

Light Output

: 80-500 inch diagonal

: 3500 ANSI lumen

Contrast Ratio

Input terminal

: 250:1 ( Full On / Off )

Fixed terminal :

Composite Video ( BNC or RCA switchable )

RGB , H, V / Y,Cr,Cb ( BNC )

S Video ( S- terminal )

Optional terminal :

2 slot prepared

: RGB signal : 0.7Vp-p 75ohm Positive(BNC)

HV sync : 0.7-4.0Vp-p(75ohm/1Kohm)

Input signal (Level)

Negative or Positive(BNC)

Duty 3-30% (H-Sync Positive)

70-97% (H-Sync Negative)

0.1-10%(V-sync Positive)

90-99.9%(V-Sync Negative)

Mix sync : 0.7-4.0Vp-p(75ohm/1Kohm)

Negative or Positive(BNC)

G sync

: 0.3-0.6Vp-p 75ohm

Sync. Negative(BNC)

Video

: 1.0Vp-p 75ohm Sync. Negative

S-Video : Y 1.0Vp-p 75ohm Sync. Negative

C0.28Vp-p 75ohm(burst level)

(3 mode acceptable)

Y, Cr, Cb : Y 1.0Vp-p 75ohm Sync. Negative

Download from Www.Somanuals.com. All Manuals Search And Download.

Convergence limits

Set-up signal

: Within one pixel

: Gray Scale signal , Cross hatch signal , All white ,

All Black , 20% white

Power supply

: AC 200V - 240V

Power consumption

Input current

: 2.3KW ( MAX)

: 12.5 A(MAX)

Safety and regulation

: Meet UL 1950

CSA : Meet CSA 950

FCC : Meet FCC class A

DHHS : Approved

DOC : Meet

Meet EMC Directive

EN55022 : Meet(Radiation)

EN55082-2 : Meet(Immunity)

EN61000-3-2, EN61000-3-3 : Meet(Disturbance)

Meet LVP Directive

EN60950 :Meet (Safety)

Cabinet dimension

: 29.5" (W) x 39.4" (D) x 15" (H) without lens

750 mm (W) x 1000 mm (D) x 380 mm (H) without lens

: 238 lbs (108 kg)

Weight

Remote controller

: Wired application

Wireless (operating distance 23 ft./7m)

: Input select ;

External control

PC control

Power On/OFF

Mute

: Supports

RS-232C / RS-422 switchable

: Full compatible

ISS-6020 Compatibility

OSD Output terminal

: D-sub shrink 15 Pin

RGB signal : 0.7Vp-p Analog out ( 75ohm )

H,V sync out : TTL

Accessory (Option)

Environment

: Input terminal Option

: Temperature 0 to 40 degree

: Humidity 20 to 90% non-condensing

: Storage -10 to 50 degree c

: 1500 Hours ( Half light out put point )

: 59 dB

Lamp life

Noise

Note: Specifications are subject to change without notice.

Download from Www.Somanuals.com. All Manuals Search And Download.

5.APPENDIX

Message List

Code

Message

PS PROTECT ERROR (Overload or failure in the mains power supply)

POWERGOOD ERROR (Insufficient voltage of +5V(D) or DLP5V in the mains power supply)

COMUNICATION ERROR (Communication setting errors in conjunction with switcher and PC control)

SIGNAL UNLOOK (Instability or failure in synchronization)

FAN STOP ERROR (Fan stoppage)

C0~CF

FLASH MEMORY ERASE ERROR (Error in system PWB)

FLASH MEMORY WRITE ERROR (Error in system PWB)

ALL STORE DATA INITIAIZING (Store ROM formatting)

PARTLY STORE DATA IS BREAKING (Error in stored data)

H-FREQUENCY LIMIT OVER (Entry of signal input at 120kHz or above)

ENGINE TEMPERATURE EROOR (Engine temperature deviating the specified range)

12CBUS EROOR (VIDEO PRO PWB or CORE PACK) (Control error in video PRO PWB/core PACK)

12CBUS ERROR (DLP ENGINE) (Engine control error)

LAMP PROTECT EROOR (Lamp source error/lamp error or lamp’s fan stop)

LAMP STATE ERROR (Lamp error)

LAMP TEMPERATURE ERROR (Lamp’s temperature error)

MUSEBUS ERROR (Error in graphic PWB)

FPGA (OSD) WRITING (Writing in FPGA)

FPGA (R) WRITING (Writing in FPGA)

FPGA (G) WRITING (Writing in FPGA)

FPGA (B) WRITING (Writing in FPGA)

o0~oF

BIOS PROGRAM STATING (Program writing being processed)

Internal processing

Download from Www.Somanuals.com. All Manuals Search And Download.

NEC Corporation

Printed in Japan

78408931

Download from Www.Somanuals.com. All Manuals Search And Download.

Milwaukee Grinder 0725 20 User Manual
MTX Audio Speaker 525W User Manual
NETGEAR Network Hardware RN31200 100NAS User Manual
Nokia Plumbing Product CVT GCU SX User Manual
Olympus Camera Accessories TCON 14B User Manual
Omnimount Indoor Furnishings 1100161 User Manual
Omron Healthcare Printer VARISPEEDF7 User Manual
Oreck Vacuum Cleaner XL3600HH User Manual
Panasonic Security Camera KX TD816NZ KX TD1232NZ User Manual
Panasonic Switch 2SA1739G User Manual