NEC Projector MT1060 User Manual

LCD Projector

MT1065/MT1060

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

LIMITED WARRANTY (USA and Canada only)

NEC SOLUTIONS’ PROJECTOR PRODUCTS

NEC Solutions (America), Inc. (hereafter NEC Solutions) warrants

this product to be free from defects in material and workmanship

under the following terms.

HOW YOU CAN GET WARRANTY SERVICE

1. To obtain service on your product, consult the dealer from whom

you purchased the product.

2. Whenever warranty service is required, the original dated invoice

(or a copy) must be presented as proof of warranty coverage. In

order to obtain warranty service, you may be required to describe

and demonstrate the problem to your dealer or to NEC Solutions.

3. All products returned to NEC Solutions for service MUST have

prior approval. To receive approval or for the name of the

nearest NEC Solutions authorized service center, call NEC

Solutions at 800-836-0655.

HOW LONG IS THE WARRANTY

NEC Solutions’ MT1065, MT1060, and MT1060R projectors

are covered by a two (2) year limited parts and labor war-

ranty from the date of the first customer purchase. The lamp

when used under normal operating conditions is warranted

for 1000 hours or six months, whichever comes first.

4. It shall be your obligation and expense to ship the product,

freight prepaid, or to deliver it to a NEC Solutions authorized

service center, in either the original package or a similar pack-

age affording an equal degree of protection.

5. In the event a product is returned to NEC Solutions for warranty

service, and it is determined that there is no product defect or that

the product condition is not covered by this limited warranty, a

diagnostic service fee may be charged to the customer.

WHO IS PROTECTED

This warranty may be enforced only by the first purchaser, and is

not transferable.

WHAT IS COVERED AND WHAT IS NOT COVERED

Except as specified below, this warranty covers all defects in

material or workmanship in this product.

LIMITATION OF IMPLIED WARRANTIES

NEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS

LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT

AT NEC SOLUTIONS’ OPTION. REPLACEMENT PRODUCTS MAY

BE NEW OR ‘LIKE NEW’. The following are not covered by the

limited warranty and NEC Solutions shall not be liable for:

EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY,

NEC SOLUTIONS MAKES NO OTHER WARRANTIES, EXPRESS

OR IMPLIED, INCLUDING BUT NOT LIMITED TO ANY IMPLIED

WARRANTIES OR CONDITIONS OF MERCHANTABILITY AND

FITNESS FOR A PARTICULAR PURPOSE. ANY IMPLIED WARRAN-

TIES THAT MAY BE IMPOSED BY LAW ARE LIMITED TO THE TERMS

AND DURATION OF THIS LIMITED WARRANTY.

1. Any product which is not distributed in the U.S.A. or Canada

by NEC Solutions or which is not purchased, installed, and

operated in the U.S.A or Canada.

2. Any product on which the serial number has been defaced,

modified or removed.

3. Normal decrease in lamp light output over time.

4. Damage, deterioration or malfunction resulting from:

a. Accident, misuse, abuse, neglect, improper ventilation, fire,

dust, smoke, water, lightning or other acts of nature, unau-

thorized product modification, or failure to follow instruc-

tions supplied with the product.

EXCLUSION OF DAMAGES

NEC SOLUTIONS’ LIABILITY FOR ANY DEFECTIVE PRODUCT IS

LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT

AT NEC SOLUTIONS’ OPTION. NEC SOLUTIONS SHALL NOT

BE LIABLE FOR:

1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS

IN THIS PRODUCT, DAMAGES BASED UPON INCONVE-

NIENCE, LOSS OF USE OF THE PRODUCT, LOSS OF TIME,

COMMERCIAL LOSS; OR

2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSE-

QUENTIAL OR OTHERWISE.

b. Repair or attempted repair by anyone other than a NEC

Solutions authorized service center.

c. Any shipment of the product (claims must be presented to

the carrier).

d. Removal or installation of the product.

HOW STATE LAW RELATES TO THE WARRANTY

SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG

AN IMPLIED WARRANTY LASTS AND/OR DO NOT ALLOW THE

EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUEN-

TIAL DAMAGES, SO THE ABOVE LIMITATIONS AND EXCLU-

SIONS MAY NOT APPLY TO YOU. THIS LIMITED WARRANTY

GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE

OTHER RIGHTS WHICH VARY FROM STATE TO STATE.

e. Any other cause which does not relate to a product defect.

f. Use of the product beyond normal operating conditions.

Normal operating conditions are defined as product use

not in excess of 8 hours per day and 260 days per year.

5. Cartons, carrying cases, shipping cases, batteries, external

cabinets, magnetic tapes, or any accessories used in connec-

tion with the product.

6. Service required as a result of third party components.

FOR MORE INFORMATION, CONTACT:

NEC SOLUTIONS (AMERICA), INC.

1250 N. Arlington Heights Road, Suite 500

Itasca, Illinois 60143-1248

WHAT NEC SOLUTIONS WILL PAY FOR

NEC Solutions will pay labor and material expenses for covered

items, but NEC Solutions will not pay for the following:

TELEPHONE 800-836-0655

www.necvisualsystems.com

1. Removal or installation charges.

2. Costs of technical adjustments, set-up, maintenance, or adjust-

ment of user controls.

3. Payment of shipping and related charges incurred in returning

the product for warranty repair.

Customers are cautioned that product performance is affected by

system configuration, software, the application, customer data,

and operator control, among other factors. While NEC Solutions’

products are considered to be compatible with many systems, the

specific functional implementation by the customers of the prod-

uct may vary. Therefore, the suitability of a product for a specific

purpose or application must be determined by the customer and

is not warranted by NEC Solutions.

Printed in Japan

7N8P1942

Download from Www.Somanuals.com. All Manuals Search And Download.

DECLARATION OF CONFORMITY

This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions.

(1) This device may not cause harmful interference, and (2) this device must accept any interference

received, including interference that may cause undesired operation.

U.S. Responsible Party: NEC Solutions (America), Inc.

Address:

1250 N. Arlington Heights Road

Itasca, Illinois 60143

(630) 467-5000

Tel. No.:

Type of Product:

LCD Projector

Equipment Classification:

Models:

Class B Peripheral

MT1065, MT1060 and MT1060R

We hereby declare that the equipment specified above

conforms to the technical standards as specified in the FCC Rules.

Download from Www.Somanuals.com. All Manuals Search And Download.

Portable Projector

MT1065/MT1060

English

Deutsch

Français

Italiano

Español

Svenska

User’s Manual

Download from Www.Somanuals.com. All Manuals Search And Download.

Important Information

RF Interference

Safety Cautions

Precautions

WARNING

Please read this manual carefully before using your NEC MT1065/

MT1060 Projector and keep the manual handy for future reference.Your

serial number is located on the right side of your projector. Record it

here:

The Federal Communications Commission does not allow any

modifications or changes to the unit EXCEPT those specified

by NEC Soluctions (America), Inc. in this manual. Failure to com-

ply with this government regulation could void your right to

operate this equipment. This equipment has been tested and

found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules.These limits are designed

to provide reasonable protection against harmful interference

in a residential installation. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and

used in accordance with the instructions, may cause harmful

interference to radio communications. However, there is no guar-

antee that interference will not occur in a particular installa-

tion. If this equipment does cause harmful interference to radio

or television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct

the interference by one or more of the following measures:

CAUTION

To turn off main power, be sure to remove the plug from power

outlet.

The power outlet socket should be installed as near to the

equipment as possible, and should be easily accessible.

CAUTION

TO PREVENT SHOCK, DO NOT OPEN THE CABINET.

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED NEC SERVICE PER-

SONNEL.

This symbol warns the user that uninsulated voltage within the

unit may be sufficient to cause electrical shock.Therefore, it is

dangerous to make any kind of contact with any part inside of

the unit.

•

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected.

This symbol alerts the user that important information con-

cerning the operation and maintenance of this unit has been

provided.

•

Consult the dealer or an experienced radio / TV technician for

help.

The information should be read carefully to avoid problems.

In UK, a BS approved power cable with moulded plug has a Black (five

Amps) fuse installed for use with this equipment. If a power cable is not

supplied with this equipment please contact your supplier.

WARNING

TO PREVENT FIRE OR SHOCK, DO NOT EXPOSETHIS UNITTO

RAIN OR MOISTURE.

Important Safeguards

DO NOT USETHIS UNIT’S GROUNDED PLUGWITH AN EXTEN-

SION CORD OR IN AN OUTLET UNLESS ALL THREE PRONGS

CAN BE FULLY INSERTED.

DO NOT OPENTHE CABINET.THERE ARE HIGH-VOLTAGE COM-

PONENTS INSIDE. ALL SERVICING MUST BE DONE BY QUALI-

FIED NEC SERVICE PERSONNEL.

These safety instructions are to ensure the long life of your projector

and to prevent fire and shock. Please read them carefully and heed all

warnings.

Installation

1. For best results, use your projector in a darkened room.

DOC Compliance Notice

2. Place the projector on a flat, level surface in a dry area away from

dust and moisture.

This Class B digital apparatus meets all requirements of the Canadian

Interference-Causing Equipment Regulations.

To avoid premature lamp failure, do not tilt the front of the projector

up or down by more than 15° from level.

Acoustic Noise Information Ordinance-3. GSGV:

3. Do not place your projector in direct sunlight, near heaters or heat

radiating appliances.

The sound pressure level is less than 70 dB (A) according

to ISO 3744 or ISO 7779.

4. Exposure to direct sunlight, smoke or steam can harm internal com-

ponents.

5. Handle your projector carefully. Dropping or jarring can damage in-

ternal components.

6. Do not place heavy objects on top of the projector.

7. If you wish to have the projector installed on the ceiling:

a. Do not attempt to install the projector yourself.

This label is on the side of the remote control.

b. The projector must be installed by qualified technicians in order

to ensure proper operation and reduce the risk of bodily injury.

CAUTION

c. In addition, the ceiling must be strong enough to support the

projector and the installation must be in accordance with any

local building codes.

Do not look into the laser pointer while it is on and do not

point the laser beam at a person. Serious injury could re-

sult.

d. Please consult your dealer for more information.

E-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Fire and Shock Precautions

What's in the Box?

Make sure your box contains everything listed. If any pieces are miss-

ing, contact your dealer.

1. Ensure that there is sufficient ventilation and that vents are unob-

structed to prevent the build-up of heat inside your projector. Allow

at least 3 inches (10 cm) of space between your projector and a

wall.

Please save the original box and packing materials if you ever need to

ship your MT1065/MT1060 Projector.

2. Prevent foreign objects such as paper clips and bits of paper from

falling into your projector.

Lens cap

Remote Control Cable

Projector

Do not attempt to retrieve any objects that might fall into your projec-

tor. Do not insert any metal objects such as a wire or screwdriver

into your projector. If something should fall into your projector, dis-

connect it immediately and have the object removed by a qualified

NEC service personnel.

3. Do not place any liquids on top of your projector.

4. Do not look into the lens while the projector is on. Serious damage

to your eyes could result.

USB mouse

OFF

5. Keep any items such as magnifying glass out of the light path of the

projector.The light being projected from the lens is extensive, there-

fore any kind of abnormal objects that can redirect light coming out

of the lens, can cause unpredictable outcome such as fire or injury

to the eyes.

VID

AUTO

ADJ.

POWER

RGB

VIEWER

LASER

PEC

EEZE

OINTE

MAG

-M

LIDE

LIST

6. Do not cover the lens with the supplied lens cap or equivalent while

the projector is on. Doing so can lead to melting of the cap and

possibly burning your hands due to the heat emitted from the light

output.

Remote control

Batteries

String and rivet

7. The projector is designed to operate on a power supply of 100-120

or 200-240 V 50/60 Hz AC. Ensure that your power supply fits this

requirement before attempting to use your projector.

8. Handle the power cable carefully and avoid excessive bending.

A damaged cord can cause electric shock or fire.

9. If the projector is not to be used for an extended period of time,

disconnect the plug from the power outlet.

Power cable

USB cable

RGB signal cable

CAUTION

1. Do not try to touch the ventilation outlet on the front as it can be-

come heated while the projector is turned on.

Quick

Connect

2. Do no use the tilt-foot for purposes other than originally intended.

Misuses such as gripping the tilt-foot or hanging on the wall can

cause damage to the projector.

Guide

User's

Manual

Software Utility

Installation GuNidEeC

3. Enable High-Speed Fan mode if you continue to use the projector

for consecutive days. (From the Advanced menu, select [Projector

Options] → [Setup] → [Page 4] → [High Speed Fan Mode].)

CD-ROM

Projector User Supportware

4. Do not unplug the power cable from the wall outlet under any one of

the following circumstances.

Doing so can cause damage to the projector:

For North America only

Registration card

Limited warranty

While the Hour Glass icon appears.

While the message "Please wait a moment." appears.This mes-

sage will be displayed after the projector is turned off.

For Europe only

Guarantee policy

While the cooling fans are running.(The cooling fans continue to

work for 90 seconds after the projector is turned off).

5. Do not eject the PC card while its data is being accessed. Doing so

can damage your PC card data.

Lamp Replacement

•

To replace the lamp, follow all instructions provided on page E-53.

Be sure to replace the lamp when the message "The lamp has

reached the end of its usable life. Please replace the lamp."

appears. If you continue to use the lamp after the lamp has reached

the end of its usable life, the lamp bulb may shatter, and pieces of

glass may be scattered in the lamp case. Do not touch them as the

pieces of glass may cause injury.

If this happens, contact your NEC dealer for lamp replacement.

•

Allow a minimum of 90 seconds to elapse after turning off the pro-

jector. Then turn off the main power switch, disconnect the power

cable and allow 60 minutes to cool the projector before replacing

the lamp.

E-3

Download from Www.Somanuals.com. All Manuals Search And Download.

TABLE OF CONTENTS

Selecting Video Filter Level .................................................................................... E-39

Selecting Noise Reduction Level ............................................................................ E-39

Signal Type ............................................................................................................ E-39

Picture Management .................................................................................................. E-39

User Adjust (when using User 1 to 4) .................................................................... E-39

Selecting Gamma Correction Mode ................................................................ E-40

Selecting Color Correction ............................................................................. E-40

Adjusting Color Temperature and White Balance ............................................ E-40

Selecting Base Setting .................................................................................... E-40

Projector Options ...................................................................................................... E-40

Using 3D Reform ................................................................................................... E-40

Cornerstone ................................................................................................... E-40

Keystone ........................................................................................................ E-40

Using Adapting Color Correction ........................................................................... E-41

Menu [Page1] ........................................................................................................ E-43

Selecting Menu Language/Selecting Menu Mode/Customizing the Menu/Select-

ing Projecting Pointer Icon/Selecting Menu Display Time

Important Information ..................................................... E-2

Safety Cautions ............................................................................................................... E-2

What's in the Box? .......................................................................................................... E-3

INTRODUCTION .............................................................. E-5

Introduction to the Projector ........................................................................................... E-5

Part Names of the Projector ............................................................................................ E-6

Attaching the lens cap ................................................................................................. E-6

Carrying the Projector ................................................................................................. E-6

Top Features ................................................................................................................ E-7

Terminal Panel Features ............................................................................................... E-8

Part Names of the Remote Control .............................................................................. E-9

Battery Installation ................................................................................................. E-11

Remote Control Precautions .................................................................................. E-11

Operating Range for Wireless Remote Control ...................................................... E-11

Using the Remote Control in Wired Operation ....................................................... E-11

Menu [Page 2] ....................................................................................................... E-43

Turning On / Off Source Display / Turning On / Off Message / Selecting Menu

Color

Setup [Page 1] ....................................................................................................... E-44

Selecting Projector Orientation/Selecting a Color or Logo for Background/Setting

RGB 1 or 2 for RGB OUT/Setting Closed Caption

Setup [Page 2] ....................................................................................................... E-44

Setting Viewer Options/Selecting Capture Options/Setting Mouse Button and Sen-

sitivity/Selecting Operation Mode

Setup [Page 3] ....................................................................................................... E-45

Selecting Signal Format [Signal Select]

Setup [Page 4] ....................................................................................................... E-45

Enabling Auto Adjust/Enabling Auto Start/Enabling Power Management/Enabling

Power Off Confirmation/Enabling Horizontal and Vertical Keystone Correction Save

/Enabling High Speed Fan Mode/Selecting Built-in Speakers/Enabling Idle Mode

Setup [Page 5] ....................................................................................................... E-46

Remote Sensor/S-Video Mode Select

Setup [Page 6] ....................................................................................................... E-46

Selecting Communication Speed/Selecting Default Source/Disabling the Cabinet

Buttons

Selecting Lamp Mode and Lamp Type ................................................................... E-46

Selecting Aspect Ratio and Position for Screen ..................................................... E-47

Selecting Auto Functions ....................................................................................... E-47

Setting LAN Mode ..................................................................................................... E-48

IP Address ............................................................................................................. E-48

Network Type ......................................................................................................... E-48

WEP ....................................................................................................................... E-49

Mail ........................................................................................................................ E-49

Status .................................................................................................................... E-50

Setting a Password .................................................................................................... E-50

Security ..................................................................................................................... E-51

Tools .......................................................................................................................... E-52

Using Sleep Timer/Using Capture/Using PC Card Files/Using ChalkBoard

Help ........................................................................................................................... E-52

Contents ................................................................................................................ E-52

Information ............................................................................................................ E-52

Returning to Factory Default ...................................................................................... E-52

INSTALLATION AND CONNECTIONS ....................................... E-12

Setting Up the Screen and the Projector ....................................................................... E-12

Selecting a Location .................................................................................................. E-12

Throw Distance and Screen Size ............................................................................... E-13

Making Connections ...................................................................................................... E-14

When Viewing a DVI Digital Signal ............................................................................ E-14

Connecting Your PC or Macintosh Computer ............................................................ E-14

To connect SCART output (RGB) ............................................................................... E-15

Connecting an External Monitor ................................................................................ E-15

Connecting Your DVD Player ..................................................................................... E-16

Connecting Your VCR or Laser Disc Player ............................................................... E-17

Connecting the Supplied Power Cable ....................................................................... E-17

PROJECTING AN IMAGE (BASIC OPERATION) ........................... E-18

Turning on the Projector ................................................................................................ E-18

Selecting a Source ......................................................................................................... E-19

Adjusting the Picture Size and Position ......................................................................... E-19

Correcting the Horizontal and Vertical Keystone Distortion (3D Reform) ...................... E-20

Optimizing RGB Picture Automatically .......................................................................... E-22

Turning Up or Down Volume ......................................................................................... E-22

Using the Laser Pointer ................................................................................................. E-22

Setting the function switch ............................................................................................ E-23

Turning off the Projector ............................................................................................... E-23

CONVENIENT FEATURES ................................................... E-24

Using the Remote Mouse Function ............................................................................... E-24

Connecting to your computer for the remote mouse function ................................... E-24

When using the USB Port .......................................................................................... E-24

Switching operation mode between computer and projector ..................................... E-24

Turning Off the Image and Sound .................................................................................. E-25

Freezing a Picture .......................................................................................................... E-25

Using the Pointer .......................................................................................................... E-25

Enlarging and Moving a Picture ..................................................................................... E-25

Getting the On-line Help ................................................................................................ E-25

Using the USB Mouse ................................................................................................... E-26

Using the USB HUB Function ........................................................................................ E-26

Changing Background Logo .......................................................................................... E-27

Making Freehand Drawings on a Projected Image (ChalkBoard) ................................... E-27

MAINTENANCE ............................................................. E-53

Replacing the Lamp ...................................................................................................... E-53

Cleaning ........................................................................................................................ E-54

Cleaning or Replacing the Filter ................................................................................. E-54

Cleaning the Cabinet and the Lens ............................................................................. E-54

USING THE VIEWER ........................................................ E-28

Making the Most out of the Viewer Function ................................................................. E-28

Operating the Viewer Function from the Projector (playback) ....................................... E-29

Projecting slides (Viewer) .......................................................................................... E-29

Auto Play Mode ......................................................................................................... E-30

Switching to Slides Directly from Other Input Modes ................................................ E-30

Viewing Digital Images .............................................................................................. E-30

Storing Images Displayed on the Projector on the PC card (Capture) ....................... E-30

Deleting Captured Images ......................................................................................... E-31

Using the PC Card Files Fucntion (PC Card Files) ...................................................... E-31

TROUBLESHOOTING ........................................................ E-55

Power Indicator ............................................................................................................. E-55

Status Indicator ............................................................................................................. E-55

Lamp Indicator .............................................................................................................. E-55

Common Problems & Solutions .................................................................................... E-56

When using the Viewer function .................................................................................... E-56

USING ON-SCREEN MENU ................................................. E-32

Basic Menu Operation ................................................................................................... E-32

Using the Menus ....................................................................................................... E-32

Customizing the Menu ............................................................................................... E-32

Menu tree ...................................................................................................................... E-33

Menu Elements ............................................................................................................. E-36

Entering Alphanumeric Characters by Using the Menu .............................................. E-37

Menu Descriptions & Functions .................................................................................... E-37

Source Select ............................................................................................................ E-37

RGB/Video/S-Video/DVI (DIGITAL)/Viewer/LAN/Entry List

Picture ....................................................................................................................... E-38

Sound ........................................................................................................................ E-38

Image Options ........................................................................................................... E-38

Selecting Aspect Ratio ........................................................................................... E-38

Masking Unwanted Area (Blanking) ....................................................................... E-39

Adjusting Position and Clock ................................................................................. E-39

Horizontal/Vertical Position .................................................................................... E-39

Selecting Resolution .............................................................................................. E-39

Selecting Overscan Percentage .............................................................................. E-39

SPECIFICATIONS ........................................................... E-57

APPENDIX ................................................................... E-58

Cabinet Dimensions ...................................................................................................... E-58

Pin Assignments of D-Sub RGB Input Connector .......................................................... E-58

Compatible Input Signal List ......................................................................................... E-59

PC Control Codes and Cable Connection ....................................................................... E-60

PC Control Connector (D-SUB 9P) ................................................................................ E-60

Using Software Keyboard .............................................................................................. E-60

Operation Using an HTTP Browser ................................................................................ E-61

TravelCare Guide ........................................................................................................... E-62

E-4

Download from Www.Somanuals.com. All Manuals Search And Download.

INTRODUCTION

•

NEC’s exclusive Advanced AccuBlend intelligent pixel blending tech-

nology - an extremely accurate image compression technology - of-

fers a crisp image with UXGA (1600

1200) resolution*³.

Introduction to the Projector

This section introduces you to your new MT1065/MT1060 Projector and

describes the features and controls.

Supports most IBMVGA, SVGA, XGA , SXGA/UXGA(with Advanced

AccuBlend)*³, Macintosh, component signal (YCbCr/ YPbPr) or any

other RGB signals within a horizontal frequency range of 24 to 100

kHz and a vertical frequency range of 48 to 120 Hz. This includes

NTSC, PAL, PAL-N, PAL-M, PAL60, SECAM and NTSC4.43 stan-

dard video signals.

Congratulations on Your Purchase of The MT1065/

MT1060 Projector

The MT1065/MT1060 is one of the very best projectors available today.

The MT1065/MT1060 enables you to project precise images up to 500

inches across (measured diagonally) from your PC or Macintosh com-

puter (desktop or notebook), VCR, DVD player, document camera, a

laser disc player or Viewer.

A UXGA (1600

1200) and SXGA image (1280

1024) are dis-

played with NEC’s Advanced AccuBlend.

You can use the projector on a tabletop or cart, you can use the projec-

tor to project images from behind the screen, and the projector can be

permanently mounted on a ceiling*¹. The remote control can be used

wirelessly.

NOTE: Composite video standards are as follows:

NTSC: U.S. TV standard for video in U.S. and Canada.

PAL: TV standard used in Western Europe.

PAL-N: TV standard used in Argentine, Paraguay and Uruguay.

PAL-M: TV standard used in Brazil.

PAL60: TV standard used for NTSC playback on PAL TVs.

SECAM: TV standard used in France and Eastern Europe.

NTSC4.43: TV standard used in Middle East countries.

Do not attempt to mount the projector on a ceiling yourself.

The projector must be installed by qualified technicians in order

to ensure proper operation and reduce the risk of bodily injury.

In addition, the ceiling must be strong enough to support the pro-

jector and the installation must be in accordance with any local

building codes. Please consult your dealer for more information.

•

The supplied remote control can be used without a cable, and you

can even use the remote control to operate your PC's mouse wirelessly

from across the room with the built-in remote mouse function.

•

You can control the projector with a PC using the PC Control port.

USB port allows USB mouse operation*⁴.

Features you'll enjoy:

•

3D Reform enhanced keystone correction that allows not only hori-

zontal and vertical access but diagonal adjustments.

The USB ports meet the USB1.1 specification.

•

The contemporary cabinet design is light, compact, easy to carry,

and complements any office, boardroom or auditorium.

•

Wireless*²or wired networking access provides easy and effective

presentation delivery.

Eight pointers are available for your presentation.

A wireless LAN card is required.The NEC optional wireless LAN

card is available. (SWL-2100N-N )

∗

About this user's manual

•

Safety protect by Password and Security functions

The fastest way to get started is to take your time and do ev-

erything right the first time. Take a few minutes now to review

the user's manual. This may save you time later on. At the be-

ginning of each section of the manual you'll find an overview. If

the section doesn't apply, you can skip it.

Password and Security features prevent the projector from being used

by unauthorized individuals.

Password prevents unauthorized individuals from changing projector

settings or adjustments Security offers complete protection by using

your PC card as a protect key so that the projector will not project a

signal without insertion of the registered PC card and unauthorized

use can be discouraged.

•

Picture Management enables users to adjust individual color settings

to their preferences.

Eco-mode extends lamp life and reduces total cost of ownership.

Standard lamp and optional longer life lamp

•

Power zoom and power focus standard lens provide easy adjust-

ment.

•

Automatic lens focus provides extreme ease of use

Automatic Wall Color Correction allows for quick adaptive color cor-

rection on textured or painted walls and in applications where the

display is other than screen material. With the built-in image sensor,

the projector adjusts the colors for screen sizes between 40" and

150" diagonally.

•

Variable audio out control via projector

The built-inViewer allows you to start your presentation even when a

PC is not available at the site.

•

A high-bright 275 watt DC lamp (220W Eco mode).

The Standby mode reduces standby power consumption significantly.

The supplied wireless remote control that operates the projector from

any angle.

•

The image can be projected between 25 and 500 inches (measured

diagonally).

•

The "Capture" enables you to capture the current projected image.

An image can be projected from in front or behind a screen, and the

projector can even be installed on the ceiling.

E-5

Download from Www.Somanuals.com. All Manuals Search And Download.

Part Names of the Projector

Remote Sensor (See page E-11)

Image Sensor

Controls (See page E-7)

Remote Sensor (See page E-11)

Built-in Security Slot ( )*

For Auto Focus and Wall Color Cor-

rection. (See page E-47)

Lens

Ventilation (inlet)

Carrying Handle

Adjustable Tilt Foot Lever

(See page E-19)

Adjustable Tilt Foot

(See page E-19)

Lens Cap

Adjustable Tilt Foot Lever

(See page E-19)

Ventilation (outlet)

Heated air is exhausted from here

Adjustable Tilt Foot (See page E-19)

This security slot supports the MicroSaver^®Security System. MicroSaver^®is a registered trademark of Kensington Microware Inc. The logo is

trademarked and owned by Kensington Microware Inc.

Lamp Cover (See page E-53)

PC Card Slot 1

PC Card Slot 2

Remote Sensor (See page E-11)

Filter Cover (inlet)

OTE

REM

PC Card Eject Button

)

MOU

(

/MON

DIO

B/C

G/Y

DIO

AC IN

Remote Sensor

(See page E-11)

RGB

DIO

L/MONO

DIO

L/MON

DIO

DEO

DIO

DEO

S-

AC Input

Stereo Speaker (5W)

Connect the supplied power cable's three-

pin plug here, and plug the other end into

an active wall outlet. (See page E-17)

Main Power Switch

When you plug the supplied power cable into

an active wall outlet and turn on the Main

Power switch, the POWER indicator turns

orange and the projector is in standby mode.

(See page E-18)

Carrying the Projector

Attaching the lens cap

Always carry your projector by the handle.

To attach the lens cap to the bottom with the supplied string and rivet:

Ensure that the power cable and any other cables connecting to video

sources are disconnected before moving the projector.

When moving the projector or when it is not in use, cover the lens with

the lens cap.

1. Thread the string through the

hole on the lens cap and then

tie a knot in the string.

2. Use the rivet to attach the

string to the bottom of the

projector.

E-6

Download from Www.Somanuals.com. All Manuals Search And Download.

11. SELECT ̆̄̇̈ (+) (–) / Volume Buttons

̆̄ : Use these buttons to select the menu of the item you wish to

adjust. When no menus appear, these buttons work as a vol-

ume control.

Top Features

11 10

̇̈ : Use these buttons to change the level of a selected menu item.

A press of the ̈ button executes the selection.When the menus

or the Viewer tool bar is not displayed, these buttons can be

used to select a slide, or to move the cursor in Folder List or

Slide List.

When the pointer is displayed, these ̆̄̇̈ buttons move the pointer.

12. ENTER Button

Executes your menu selection and activates items selected from the

menu.

12 13 14

)

13. CANCEL Button

Press this button to exit "Menus". Press this button to return the ad-

justments to the last condition while you are in the adjustment or

setting menu.

1. POWER Button (ON / STAND BY)(

Use this button to turn the power on and off when the main power is

supplied and the projector is in standby mode.

14. PC CARD Access Indicator 1/2

Lights while accessing a PC card.

NOTE: To turn on or off the projector, press and hold this button for a mini-

mum of two seconds.

2. POWER Indicator

When this indicator is green, the projector is on; when this indicator

is orange, it is in standby or idle mode. See the Power Indicator sec-

tion on page E-55 for more details.

3. STATUS Indicator

If this light blinks red rapidly, it indicates that an error has occurred,

the lamp cover is not attached properly or the projector has over-

heated.If this light remains orange, it indicates that you have pressed

a cabinet key while the Control Panel Key Lock is enabled. See the

Status Indicator section on page E-55 for more details.

4. LAMP Indicator

If this light blinks red rapidly, it's warning you that the lamp has reached

the end of its usable life. After this light appears, replace the lamp as

soon as possible (See page E-53). If this is lit green continually, it

indicates that the lamp mode is set to Eco. See the Lamp Indicator

section on page E-55 for more details.

5. SOURCE Button

Use this button to select a video source such as a PC, VCR, DVD

player, Viewer (PC card), or LAN.

Press and release this button quickly to display the Source List.

Each time this button is pressed for a minimum of ONE second, the

input source will change as follows:

RGB1 → RGB2 → Video → S-Video → DVI (DIGITAL) → Viewer → RGB1 → ...

If no input signal is present, the input will be skipped.

6. AUTO ADJUST Button

Use this button to adjust Position-H/V and Pixel Clock/Phase for an

optimal picture (See page E-22).Also press and hold this button for a

minimum of 2 seconds to enable the Auto Focus or Auto Wall Color

Correction function (See page E-47).

7. 3D REFORM Button

Press this button to enter 3D Reform mode to correct the keystone

(trapezoidal) distortion, and make the image square.

8. ZOOM Button (+/-)

Zoom the lens in and out.

9. FOCUS Button (+/-)

Adjust the lens focus.

10. MENU Button

Displays the menu.

E-7

Download from Www.Somanuals.com. All Manuals Search And Download.

5. S-VIDEO IN Connector (Mini DIN 4 Pin)

Here is where you connect the S-Video input from an external source

like a VCR.

Terminal Panel Features

9 10 13

NOTE: S-Video provides more vivid color and higher resolution than the tra-

ditional composite video format.

S-VIDEO AUDIO Input Jacks R/L (RCA)

These are your left and right channel audio inputs for stereo sound

from an S-Video source.

6. VIDEO IN Connector (RCA)

Connect a VCR, DVD player, laser disc player, or document camera

here to project video.

VIDEO AUDIO Input Jacks R/L (RCA)

These are your left and right channel audio inputs for stereo sound

from a Video source.

1. RGB1 IN / Component Input Connector (Mini D-Sub 15 Pin)

Connect your computer or other analog RGB equipment such as IBM

compatible or Macintosh computers. Use the supplied RGB cable to

connect to your computer. This also serves as a component input

connector that allows you to connect a component video output of

component equipment such as a DVD player. This connector also

supports SCART output signal. See page E-15 for more details.

7. AUDIO OUT Jacks R/L (RCA)

You can use this connector to output sound from the currently se-

lected input source (RGB 1, RGB 2, DVI (DIGITAL),Video or S-Video).

Output sound level can be adjusted in accordance with the sound

level of the internal speaker.

RGB1 AUDIO Input Mini Jack (Stereo Mini)

8. USB Port (MOUSE/HUB) [Type A]

This is where you connect the audio output from your computer or

DVD player when connected to the RGB1 input.A commercially avail-

able audio cable is required.

Connect the supplied USB mouse.You can operate the menu orViewer

with the USB mouse via this port.

•

A USB-supported scanner or PC peripheral can be connected

to this port. (USB Hub Function)

2. RGB2 IN / Component Input Connectors (BNC)

Connect R,G,B,H (Horizontal sync) and V (Vertical sync) outputs of

external equipment.

9. USB Port (PC) [Type B]

Connect this port to the USB port (type A) of your PC using the sup-

plied USB cable.You can operate your computer's mouse functions

from the remote control. This port also serves as a PC Control port

by using Dynamic Image Utility 2.0 included on the supplied CD-

ROM.

If using a component with a combined sync (SYNC) output, connect

it to the H/V terminal.

When using luminance and color-difference signals of HDTV and DVD,

connect Pr/Cr to the R,Y to the G and Pb/Cb to the B input of the

projector.

10. REMOTE (Mini Jack)

Connect your remote control cable here for wired operation.

NOTE: The RGB IN 2 does not support Plug & Play.

RGB2 AUDIO IN Mini Jack (Stereo Mini)

11. PC CONTROL Port (D-Sub 9 Pin)

This is where you connect audio output from your computer or DVD

player connected to the RGB2 input. A commercially available audio

cable is required.

Use this port to connect your PC to control your projector via a serial

cable. This enables you to use your PC and serial communication

protocol to control the projector. A commercially available RS232C

cross cable is required to use this port.You can also control the pro-

jector by using Dynamic Image Utility 2.0 included on the supplied

CD-ROM.

To do so you must first have Dynamic Image Utility 2.0 installed on

your PC.If you are writing your own program, typical PC control codes

are on page E-60.

3. DVI IN Connector (24 pin)

This connector can be used to accept a digital signal output from a

computer or other sources with a DVI connector.

DVI AUDIO Input Mini Jack (Stereo Mini)

This is where you connect the audio output from your computer when

connected to the DVI input. A commercially available audio cable is

required.

12. PC CARD Slot 1/2

Insert a PC card, commercially available LAN card or NEC optional

wireless LAN card here.

There are two slots: Slot 1 and Slot 2.

4. RGB OUT Connector (Mini D-Sub 15 Pin)

You can use this connector to loop your computer image to an exter-

nal monitor from the RGB 1 or 2 input source.

The RGB analog signal set on RGBOUT Terminal is output during

idle mode. See pages E-15 and 45.

NOTE: A dummy card is inserted into each slot at the time of shipment. First

remove the dummy cards before use.

13. PC CARD Eject Button 1/2

Press to eject a PC card partially. Each slot has its own eject button:

1 and 2.

RGB AUDIO OUT Mini Jack (Stereo Mini)

Connect an additional audio equipment here to listen to audio com-

ing from your computer connected to RGB1, RGB2 or DVI input.

Note that there is no audio output from this jack during Standby and

Idle.

E-8

Download from Www.Somanuals.com. All Manuals Search And Download.

9. VIEWER Button

Press this button to select the Viewer source.

Part Names of the Remote Control

NOTE: If you are using a Macintosh computer, you can click either the right-click

or left-click button to activate the mouse.

10. AUTO ADJ Button

Use this button to adjust an RGB source for an optimal picture. Also

press and hold this button for a minimum of 2 seconds to enable the

Auto Focus or Auto Wall Color Correction function. See page E-20 or

22.

U T E

I C - M

1. Infrared Transmitter

R E F O R M

3 D

E E

Direct the remote control toward

the remote sensor on the projec-

tor cabinet.

P J

S E L E C T

S E R

E R

I E

11. LASER Button

G B

J .

2. LASER Pointer

Beams a laser light when the LA-

SER button is pressed.

O N

T O

E R

Press and hold this button to activate the laser pointer.When lit, you

can use the laser to draw your audience's attention to a red dot that

you can place on any object.

P O W

I D

F F

3. Remote Jack

Connect your remote control

cable here for wired operation.

12. MENU Button

Displays the menu for various settings and adjustments.

13. SELECT ̆̄̇̈ (Mouse) Button

When you are in the Computer mode, these buttons work as a com-

puter mouse.

When you are in the Projector mode, which is indicated by lighting

the PJ button. See page E-24.

OFF

POWER

̆̄ : Use these buttons to select the menu of the item you wish

to adjust.

VIDEO

RGB

VIEWER

LASER

̇̈ : Use these buttons to change the level of a selected menu

item. A press of the ̈ button executes the selection.

When the pointer is displayed, these ̆̄̇̈ buttons move the pointer.

When the pointer is not displayed, these ̆̄̇̈ buttons are for adjust-

ing the image.

AUTO ADJ.

SELECT

14. ENTER (Left Click) Button

When you are in the Computer mode, this button works as the mouse

left button. When this button is pressed and held for a minimum of 2

seconds, the drag mode is set. When you are in the Projector mode,

which is indicated by lighting the PJ button: Use this button to enter

your menu selection. It works the same way as the ENTER button on

the cabinet. See page E-7.

ASPECT FREEZE 3D REFORM

15. CANCEL (Right Click) Button

HELP

POINTER PIC-MUTE

When you are in the Computer mode, this button works as the mouse

right button. When you are in the Projector mode, which is indicated

by lighting the PJ button: Press this button to exit the Menus. It works

the same way as the CANCEL button on the cabinet. See page E-7.

SLIDE

VOLUME MAGNIFY

ZOOM

FOCUS

FOLDER

SLIDE

16. PJ Button

Press this button to switch the SELECT, CANCEL, and ENTER but-

tons between the Projector mode (lit red) and the Computer mode.

Press this button or any one of the POWER ON/OFF, MENU, AS-

PECT, 3D REFORM, HELP, POINTER, MAGNIFY,VIEWER, FOLDER

LIST or SLIDE LIST buttons to switch to the Projector mode and the

PJ button lights red.To switch back to the Computer mode, press the

PJ button again. See page E-24.

LIST

4. LED

Flashes when any button is pressed.

17. ASPECT Button

5. POWER ON Button

Press this button to display the Aspect Ratio select screen.See page

E-38.

When the main power is on, you can use this button to turn your

projector on.

NOTE: To turn on the projector, press and hold the POWER ON button for a

minimum of two seconds.

18. FREEZE Button

This button will freeze a picture. Press again to resume motion.

6. POWER OFF Button

You can use this button to turn your projector off.

19. 3D REFORM Button

Press this button to enter 3D Reform to correct the keystone (trap-

ezoidal) distortion, and make the image square. See page E-20.

NOTE: To turn off the projector, press and hold the POWER OFF button for a

minimum of two seconds.

20. HELP Button

7. VIDEO Button

Provides the online help or the set information.

Press this button to toggle between Video and S-Video inputs.

21. POINTER Button

8. RGB Button

Press this button to display one of the eight pointers; press again to

hide the pointer.You can move your pointer icon to the area you want

on the screen using the Select ̆̄̇̈ button. See page E-25.

Press this button to select RGB 1, RGB 2 or DVI (DIGITAL) inputs.

Each time this button is pressed, the input source will change as

follows:

RGB 1 → RGB 2 → DVI (DIGITAL) → RGB 1 → ...

E-9

Download from Www.Somanuals.com. All Manuals Search And Download.

OFF

POWER

RGB

VIDEO

VIEWER

LASER

AUTO ADJ.

SELECT

ASPECT FREEZE 3D REFORM

HELP

POINTER PIC-MUTE

SLIDE

VOLUME MAGNIFY

ZOOM

FOCUS

FOLDER

SLIDE

LIST

22. PICTURE MUTE Button

This button turns off the image and sound for a short period of time.

Press again to restore the image and sound.

NOTE: When the menu is displayed, a press of this button mutes an image

and sound without turning off the menu.

23. VOLUME (+)(–) Button

Press (+) to increase the volume and (–) to decrease it.

24. MAGNIFY (+)(–) Button

Use this button to adjust the image size up to 400%.When the pointer

is displayed, the image is magnified about the center of the pointer.

When the image is magnified, the pointer is changed to the magnify-

ing icon.

When the pointer is not displayed, the image is magnified about the

center of the screen. See page E-25.

25. ZOOM (+)(–) Button

Zoom the lens in and out.

26. FOCUS (+)(–) Button

Adjust the lens focus.

27. SLIDE (+)(–) Button

Press (+) to select the next folder or slide and (–) to select the previ-

ous folder or slide. See page E-29.

28. FOLDER LIST Button

Press this button to select Viewer source to display a list of folders

included in a PC card. See page E-29.

29. SLIDE LIST Button

Press this button to select Viewer source to display a list of slides

included in a PC card. See page E-29.

NOTE: The default is the Computer mode, which allows you to use the SELECT,

CANCEL, and ENTER buttons as your computer mouse. When the POWER ON/

OFF, MENU, ASPECT, 3D REFORM, HELP, POINTER, MAGNIFY, VIEWER, FOLDER

LIST, or SLIDE LIST button is pressed, the PJ button lights red to indicate that

you are in the Projector mode. If no buttons are pressed within 60 seconds, the

light goes out and the Projector mode is canceled.

E-10

Download from Www.Somanuals.com. All Manuals Search And Download.

Battery Installation

Remote Control Precautions

1. Press firmly and slide the battery cover off.

•

Handle the remote control carefully.

If the remote control gets wet, wipe it dry immediately.

Avoid excessive heat and humidity.

If you will not be using the remote control for a long time, remove the

batteries.

•

Do not place the batteries upside down.

Do not use new and old batteries together, or use different types of

batteries together

2. Remove both old batteries and install new ones (AA). Ensure that

you have the batteries' polarity (+/-) aligned correctly.

Operating Range for Wireless Remote Control

Remote sensor on the

projector cabinet

7m/22 feet

3. Slip the cover back over the batteries until it snaps into place. Do not

mix different types of batteries or new and old batteries.

7m/22 feet

Remote control

Remote sensor on the

projector cabinet

•

The infrared signal operates by line-of-sight up to a distance of about

22 feet/7 m and within a 60-degree angle of the remote sensor on the

projector cabinet.

Note on Remote Control Operation:

If you press and hold the SELECT ̆̄̇̈ button while installing new

batteries, the remote control may fail to work properly.

Should this happen, remove the batteries and then install them again

without touching the SELECT button.

The projector will not respond if there are objects between the re-

mote control and the sensor, or if strong light falls on the sensor.

Weak batteries will also prevent the remote control from properly

operating the projector.

Using the Remote Control in Wired Operation

Connect one end of the supplied remote cable to the REMOTE mini

jack and the other end to the remote jack on the remote control.

REMOTE

OFF

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

HELP

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

LIST

E-11

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION AND CONNECTIONS

This section describes how to set up your projector and how to connect video and audio sources.

Your projector is simple to set up and use.

But before you get started, you must first:

z Set up a screen and the projector.

x Connect your computer or video equip-

ment to the projector. See page

E-14 – 17.

c Connect the supplied power cable. See

page E-17.

NOTE: Ensure that the power cable and any

other cables are disconnected before moving

the projector. When moving the projector or

when it is not in use, cover the lens with the

lens cap.

To the wall outlet.

Setting Up the Screen and the Projector

Selecting a Location

The further your projector is from the screen or wall, the larger the image. The minimum size the image can be is approximately 25" (0.64 m)

measured diagonally when the projector is roughly 39.4 inches (1.0 m) from the wall or screen.The largest the image can be is 500" (12.7 m) when

the projector is about 614.2 inches (15.6 m) from the wall or screen. Use the drawing below as a guide.

Screen size (Unit: cm/inch)

609.6(W)X457.2(H)/240(W)X180(H)

487.7(W)X365.8(H)/192(W)X144(H)

406.4(W)X304.8(H)/160(W)X120(H)

Screen Size

365.8(W)X274.3(H)/144(W)X108(H)

300"

240"

304.8(W)X228.6(H)/120(W)X90(H)

200"

243.8(W)X182.9(H)/96(W)X72(H)

180"

203.2(W)X152.4(H)/80(W)X60(H)

150"

162.6(W)X121.9(H)/64(W)X48(H)

120"

121.9(W)X91.4(H)/48(W)X36(H)

100"

81.3(W)X61.0(H)/32(W)X24(H)

61.0(W)X45.7(H)/24(W)X18(H)

TELE: 50.8(W)X38.1(H)/20(W)X15(H)

80"

60"

40"

30"

Lens center

25"

1.0

1.1

1.4

2.1

2.8

3.5

6.4

4.3

5.3

7.1

8.5

10.6

WARNING: To avoid premature lamp failure, do not tilt the front of the

Distance (Unit: m)

projector up or down by more than 15° from level.

E-12

Download from Www.Somanuals.com. All Manuals Search And Download.

Throw Distance and Screen Size

The following shows the proper relative positions of the projector and screen. Refer to the table to determine the position of installation.

Distance Chart

Screen Size

Diagonal

inch

Width

inch

120

144

160

168

192

209

216

240

280

320

360

400

Height

inch

Wide – Tele

inch

Wide – Tele

degree

Screen Width

inch

8.0

9.0

–––

35.1

39.6

47.8

64.4

–––

14.4

14.2

14.0

13.9

13.8

13.7

10.7

10.5

10.4

10.3

–––

12.0

18.0

20.0

22.0

24.0

25.0

27.0

30.0

36.0

45.0

54.0

60.0

63.0

72.0

78.0

81.0

90.0

105.0

120.0

135.0

150.0

47.4

72.1

97.6

Screen Diagonal

80.7

86.9

96.8

109.2

117.5

130.8

137.4

147.4

164.0

197.2

246.9

296.7

329.9

346.5

396.3

431.1

446.0

495.8

578.7

–––

Screen Height

Screen center

101.7

109.1

121.4

146.1

183.1

220.1

244.8

257.1

294.1

320.0

331.1

368.1

429.8

491.5

553.2

614.8

100

120

150

180

200

210

240

261

270

300

350

400

450

500

(B)

108

120

126

144

157

162

180

210

240

270

300

Screen Bottom

Lens Center

Throw Angle (Ͱ)

–––

Throw Distance (C)

Screen Size

Diagonal

635

Width

508

610

813

Height

381

457

610

Wide – Tele

degree

191

229

305

457

511

549

610

640

–––

891

1005

1215

1636

2479

2774

2985

3322

3490

3743

4165

5007

6272

7536

8379

8800

–––

14.4

14.2

14.0

13.9

13.8

13.7

10.7

10.5

10.4

10.3

–––

762

B = Vertical distance between lens center and screen center

C = Throw distance

α = Throw angle

1016

1524

1702

1829

2032

2134

2286

2540

3048

3810

4572

5080

5334

6096

6629

6858

7620

8890

10160

11430

12700

1204

1831

2050

2207

2458

2583

2771

3084

3711

4651

5591

6217

6531

1219

1361

1463

1626

1707

1829

2032

2438

3048

3658

4064

4267

4877

5304

5486

6096

7112

8128

9144

10160

914

1021

1097

1219

1280

1372

1524

1829

2286

2743

3048

3200

3658

3978

4115

4572

5334

6096

6858

7620

NOTE: Distances may vary +/-5%.

686

762

914

1143

1372

1524

1600

1829

1989

2057

2286

2667

3048

3429

3810

7471 - 10064

8129 - 10949

8410 - 11328

9350 - 12593

10917 - 14700

12484

14050

15617

–––

WARNING

Reflecting the Image

Installing your projector on the ceiling must be done by a quali-

fied technician. Contact your NEC dealer for more information.

Using a mirror to reflect your projector's image enables you to enjoy a

much larger image. Contact your NEC dealer if you need a mirror. If

you're using a mirror and your image is inverted, use the MENU and

SELECT buttons on your projector cabinet or ̆̄ buttons on your re-

mote control to correct the orientation. (See page E-44.)

Do not attempt to install the projector yourself.

•

To avoid premature lamp failure, do not tilt the front of the projector

up or down by more than 15° from level.

•

Only use your projector on a solid, level surface. If the projector falls

to the ground, you can be injured and the projector severely dam-

aged.

Do not use the projector where temperatures vary greatly. The pro-

jector must be used at temperatures between 32˚F (0˚C) and 95˚F

(35˚C).

•

Do not expose the projector to moisture, dust, or smoke. This will

harm the screen image.

Ensure that you have adequate ventilation around your projector so

heat can dissipate. Do not cover the vents on the side or the front of

the projector.

E-13

Download from Www.Somanuals.com. All Manuals Search And Download.

Making Connections

NOTE: When using with a notebook PC, be sure to connect between the projector and the notebook PC before turning on the power to the notebook PC. In most

cases signal cannot be output from RGB output unless the notebook PC is turned on after connecting with the projector.

* If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management software.

* If you accidentally hit the POWER button on the remote control, wait 90 seconds and then press the POWER button again to resume.

When Viewing a DVI Digital Signal:

To project a DVI digital signal, be sure to connect the PC and the projector using a DVI-D signal cable (not supplied) before turning on your PC or

projector. Turn on the projector first and select DVI (DIGITAL) from the source menu before turning on your PC.

Failure to do so may not activate the digital output of the graphics card resulting in no picture being displayed. Should this happen, restart your PC.

Do not disconnect the DVI-D signal cable while the projector is running. If the signal cable has been disconnected and then re-connected, an image

may not be correctly displayed. Should this happen, restart your PC.

NOTE:

•

Use the DVI-D cable compliant with DDWG (Digital Display Working Group) DVI (Digital Visual Interface) revision 1.0 standard. The DVI-D cable should be within

5 m (196") long.

•

The DVI (DIGITAL) connector accepts VGA (640x480), SVGA (800x600), 1152x864, XGA (1024x768) and SXGA (1280x1024 @ up to 60Hz).

Connecting Your PC or Macintosh Computer

DVI IN

RGB 2 IN

RGB 1 IN

DVI-D cable (not supplied)

Audio cable (not supplied)

RGB signal cable (supplied)

To mini D-Sub 15-pin connec-

tor on the projector. It is recom-

mended that you use a com-

mercially available distribution

amplifier if connecting a signal

cable longer than the supplied

one.

IBM PC or Compatibles (Desktop type)

or Macintosh (Desktop type)

PHONE

NOTE: For older Macintosh,

PHONE

use a commercially available

pin adapter (not supplied) to

connect to your Mac's video

port.

IBMVGA or Compatibles (Notebook type)

or Macintosh (Notebook type)

Connecting your PC or Macintosh computer to your projector will en-

able you to project your computer's screen image for an impressive pre-

sentation.

Connecting to RGB 2 IN connectors

Use a BNC

5 cable to connect your PC and the RGB 2 IN connectors

on your projector.

To connect to a PC or Macintosh, simply:

Connecting Your PC with a DVI Connector

1. Turn off the power to your projector and computer.

Use a DVI-D signal cable (not supplied) to connect a DVI connector of

your PC to the projector.

2. Use the supplied signal cable to connect your PC or Macintosh to the

projector.

3. Turn on the projector and the computer.

NOTE: The MT1065/MT1060 is not compatible with video decoded outputs of

4. If the projector goes blank after a period of inactivity, it may be caused

by a screen saver installed on the computer you've connected to the

projector.

NEC ISS-6020 and ISS-6010.

E-14

Download from Www.Somanuals.com. All Manuals Search And Download.

To connect SCART output (RGB)

Before connections: An exclusive SCART adapter (ADP-SC1) and a

commercially available SCART cable are required for this connection.

1. Turn off the power to the projector and your video equipment.

2. Use the NEC ADP-SC1 SCART adapter and a commercially avail-

able SCART cable to connect the RGB 1 input of your projector and

a SCART output (RGB) of your video equipment.

NOTE:

• Audio signal is not available for this connection.

• The RGB IN 2 connector does not support Plug & Play.

3. Turn on the power to the projector and your video equipment.

4. Use the RGB 1 button on the remote control to select the RGB 1

input.

5. Press the MENU button on the remote control to display the menu.

Projector

Video equipment

such as DVD player

6. From the Advanced menu, select [Projector Options] → [Setup] →

[Page 3] → [Signal Select RGB1] → [Scart].

RGB 1 IN

SCART is a standard European audio-visual connector forTVs,VCRs

and DVD players. It is also referred to as Euro-connector.

NOTE: The ADP-SC1 SCART adapter is obtainable from your NEC dealer in Eu-

rope. Contact your NEC dealer in Europe for more information.

To RGB IN 1

Commercially available Female

SCART cable

ADP-SC1

Connecting an External Monitor

RGB OUT

LINE IN

PHONE

You can connect a separate, external monitor to your projector to simul-

taneously view on a monitor the RGB analog image you're projecting.

To do so:

NOTE:

•

The RGB OUT connector outputs RGB signal during idle mode (See page E-

45). When the projector goes into idle mode, the image on an external moni-

tor disappears for a moment. Note that the RGB OUT connector will not out-

put RGB signal during Standby mode.

1. Turn off the power to your projector, monitor and computer.

2. Use a 15-pin cable to connect your monitor to the RGB OUT (Mini D-

Sub 15 pin) connector on your projector.

•

When the projector is in the Idle mode, the image may not be correctly dis-

played while the cooling fans are running immediately after turning on or off

the power. Note that the RGB OUT connector will not output RGB signal dur-

ing Standby mode.

3. Turn on the projector, monitor and the computer.

•

Daisy chain connection is not possible.

E-15

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Your DVD Player

RGB 2 IN

RGB 1 IN

Optional 15-pin-to-RCA

(female)

3 cable (ADP-CV1)

RCA(female)-to-BNC(male)

adapter (not supplied)

Component video RCA

3 cable

(not supplied)

Audio Equipment

AUDIO IN

DVD player

AUDIO OUT

Component

Cb Cr

Audio cable

(not supplied)

You can connect your projector to a DVD player with component output

or Video output. To do so, simply:

For a DVD player without component video (Y,Cb,Cr) output, use com-

mon RCA cables (not provided) to connect a composite VIDEO out-

put of the DVD player to the Video Input of the projector.

1. Turn off the power to your projector and DVD player.

3. Turn on the projector and DVD player.

2. If your DVD player has the component video (Y,Cb,Cr) output, use a

commercially available component video cable (RCAX3) and the op-

tional 15-pin-to-RCA (female)

3 cable to connect your DVD player

to the RGB IN1 or IN2 connector on the projector.

NOTE: Refer to your DVD player's owner's manual for more information about

your DVD player's video output requirements,

E-16

Download from Www.Somanuals.com. All Manuals Search And Download.

Connecting Your VCR or Laser Disc Player

VIDEO IN

S-VIDEO IN

Video cable (not supplied)

S-video cable (not supplied)

Audio equipment

AUDIO IN

VCR/ Laser disc player

AUDIO OUT

VIDEO OUT

S-VIDEO OUT

Audio cable (not supplied)

Use common RCA cables (not provided) to connect your VCR, laser

disc player or document camera to your projector.

To make these connections, simply:

NOTE: Refer to your VCR or laser disc player owner's manual for more informa-

tion about your equipment's video output requirements.

NOTE: An image may not be displayed correctly when a Video or S-Video source

is played back in fast-forward or fast-rewind via a scan converter.

1. Turn off the power to the projector and VCR, laser disc player or

document camera.

2. Connect one end of your RCA cable to the video output connector on

the back of your VCR or laser disc player, connect the other end to

the Video input on your projector. Use an audio cable (not supplied)

to connect the audio from your VCR or laser disc player to your audio

equipment (if your VCR or laser disc player has this capability). Be

careful to keep your right and left channel connections correct for

stereo sound.

3. Turn on the projector and the VCR or laser disc player.

Connecting the Supplied Power Cable

Connect the supplied power cable to the projector.

First connect the supplied power cable's three-pin plug to

the AC IN of the projector, and then connect the other

plug of the supplied power cable in the wall outlet.

PC CONTROL

)

MOUSE/HUB

(

USB

L/MONO

AUDIO

B/Cb

DVI IN

AUDIO OUT

G/Y

AUDIO

RGB OUT

AUDIO

L/M

AUDIO

L/M

AUDIO

VIDEO

AUDIO

S-VIDE

E-17

Download from Www.Somanuals.com. All Manuals Search And Download.

PROJECTING AN IMAGE (BASIC OPERATION)

This section describes how to turn on the projector and to project a

picture onto the screen.

2. Press the ENTER button to execute the selection.

Turning on the Projector

NOTE:

• When plugging in or unplugging the supplied power cable, make sure that the

main power switch is pushed to the off[O] position. Failure to do so may cause

damage to the projector.

SELECT

• The projector has two power switches: main power switch and POWER button

(POWER ON and OFF on the remote control)

• The projector has a feature to prevent itself from being used by unauthorized

individuals. To use this feature, register your PC card as a protect key. See

"Security" in "Projector Options" on page E-51 for more details.

To turn on the main power to the projector, press the Main Power switch

to the ON position ( I ).

3. The Basic menu will be displayed in the language you have selected.

Before you turn on your projector, ensure that the computer or video

source is turned on and that your lens cap is removed.

Only after you press the ON/STAND BY button on the projector cabinet

or POWER ON button on the remote control for a minimum of 2 sec-

onds will the power indicator turn to green and the projector become

ready to use.

To close the menu, press the CANCEL button.

SELECT

Note on Startup screen (Menu Language Select screen)

When you first turn on the projector, you will get the Startup screen.This

screen gives you the opportunity to select one of the seven menu lan-

guages: English, German, French, Italian, Spanish, Swedish and Japa-

nese.

After this has been done, you can proceed to the advanced menu op-

eration.

To select a menu language, follow these steps:

If you want, you can select the menu language later. See "Language"

on page E-43.

1. Use the SELECT ̆ or ̄ button to select one of the seven languages

for the menu.

NOTE: To turn the projector on by plugging in the power cable, first turn on the

Main Power switch to ON and use the menu and enable the "Auto Start" feature.

(See page E-45.) Immediately after turning on the projector, screen flicker may

occur. This is not a fault. Wait 3 to 5 minutes until the lamp lighting is stabilized.

SELECT

When the Lamp mode is set to Eco, the Lamp indicator will light green.

If one of the following things happens, the projector will not turn on.

If the internal temperature of the projector is too high, the projector

detects abnormal high temperature. In this condition the projector

will not turn on to protect the internal system. If this happens, wait for

the projector's internal components to cool down.

When the lamp reaches its end of usable life, the projector will not

turn on. If this happens, replace the lamp.

If the lamp fails to light, and if the STATUS indicator flashes on and

off in a cycle of six times, wait a full minute and then turn on the

power.

E-18

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting a Source

Adjusting the Picture Size and Position

Place your projector on a flat level surface and ensure that the projector

is square to the screen.

Selecting the computer or video source

Using the Remote Control

Lift the front edge of the projector to center the image vertically.

OFF

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

Press any one of the RGB, VIDEO or

VIEWER buttons.

ASPECT FREEZE 3D REFORM

HELP

POINTER PIC-MUTE

VOLUME MAGNIFY

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

Move the projector left to center the image horizontally on the screen.

LIST

NOTE: If no input signal is available, the projector will display a blue background

(factory preset).

Selecting from Source List

Source List

If the projected image does not appear square to the screen then

use the 3D Reform feature for proper adjustment. See page E-20.

Adjust the Tilt Foot

1. Lift the front edge of the projector.

Press and quickly release the SOURCE button on the projector cabinet

to display the Source list.Each time the SOURCE button is pressed, the

input source will change as follows: "RGB1", "RGB2" (computer or DVD

with component output) , "Video" (VCR, document camera, or laser disc

player), S-Video", "DVI (Digital)", "Viewer" (slides on a PC card), or "LAN"

(wired or wireless signal aired from a PC).

To display the selected source, press the ENTER button.

Detecting the Signal Automatically

Adjustable Tilt Foot Lever

Adjustable Tilt Foot

Adjustable Tilt Foot Lever

2. Push up the Adjustable Tilt Foot Levers on the right and left sides of

the projector to extend the adjustable tilt feet (maximum height).

3. Push down the Adjustable Tilt Foot Levers.

Press and hold the SOURCE button for a minimum of 1 second, the

projector will search for the next available input source. Each time you

press and hold the SOURCE button, the input source will change as

follows:

→ RGB1 → RGB2 → Video → S-Video → DVI (Digital) → Viewer 

If no input signal is present, the input will be skipped. When the input

source you wish to project is displayed, release the button.

Press the ENTER button.

4. Lower the front of the projector to the desired height (max. 44.5mm/

1.8”) and release the AdjustableTilt Foot Lever to lock the Adjustable

tilt foot. There is approximately 10 degrees of up and down adjust-

ment for the front of the projector.

WARNING: To avoid premature lamp failure, do not tilt the front of the

projector up or down by more than 15° from level.

E-19

Download from Www.Somanuals.com. All Manuals Search And Download.

CAUTION:

Correcting the Horizontal and Vertical Key-

stone Distortion (3D Reform)

Do not use the tilt-foot for purposes other than originally intended.

Misuses such as gripping the tilt-foot or hanging on the wall can

cause damage to the projector.

Use the 3D Reform feature to correct keystone (trapezoidal) distortion

to make the top or bottom and the left or right side of the screen longer

or shorter so that the projected image is rectangular.

In the following description, 3D Reform (Cornerstone) correction can be

done with the USB mouse or remote control, cabinet buttons.

Zoom

Use the ZOOM Button (+/-) to fine adjust the image size on the screen

When using the USB connected to the projector

Preparation: Connect the USB mouse to the projector. See page E-26.

1. Project an image so that the screen is smaller than the area of the

raster.

2. Pick up any one of the corners and align the corner of the screen

with the one of the image. (The drawing shows the upper right cor-

ner.)

Projected image

You can use ZOOM +/- button to enlarge or reduce an image size within

a range of +/-15%.

Focus

Use the FOCUS Button (+/-) to obtain the best focus.

Screen

3. Press the 3D REFORM button on the remote control.

The Cornerstone adjustment screen is displayed.

The Cornerstone adjustment screen will disappear when you move

the USB mouse cursor.

4. Point to one of the remaining 3 corners and left-click on it.

Left-click on the corner.

Using Auto Focus

Press and hold the AUTO ADJUST button on the cabinet or AUTO ADJ

button on the remote control for a minimum of 2 seconds. The focus

pattern will be displayed for a moment and then the best focus will be

automatically obtained.

Screen

NOTE: The Auto Functions have two options: Focus and Wall Color Correction.

When the AUTO ADJUST or AUTO ADJ button is pressed and held for a mini-

mum of 2 seconds, either item can be executed. You can decide in advance

which item will be enabled at the time of execution.

From the Advanced menu, select [Projector Options] → [Auto Functions]. You

can turn on or off "Focus" and "Wall Color Correction". See page E-47.

NOTE: Just pressing quickly the AUTO ADJUST button on the cabinet or AUTO

ADJ button on the remote control will enable the Auto Adjust feature instead of

the Auto Focus feature.

5. Do the above step 4 for the other two corners so that the projected

area becomes smaller than the screen.

Screen

Left-click on each corner.

E-20

Download from Www.Somanuals.com. All Manuals Search And Download.

6. To complete the procedure, right-click anywhere on the screen.

The confirmation screen is displayed.

4. Use the SELECT ̆̄̇̈ button to select one icon which points in

the direction you wish to move the projected image frame.

7. Left-click on "OK".

This completes the Cornerstone adjustment.

To return the Cornerstone adjustment to the default settings, left-

click on "Reset" in Step 7.

You can save your Cornerstone changes.The changes are saved when

you turn off the projector.To do so, select [Projector Options] → [Setup]

→ [Page 4]. Select the 3D Reform Save check box.This is not selected

at the time of shipment.

Screen

* There are limitations of shapes which can be corrected using the Cor-

nerstone adjustment.

When adjusting the Cornerstone beyond these limits, you will get the

message "Out of adjustment range!" and no correction can be done.

Should this happen, do the Cornerstone adjustment again within the

allowable range.

* Due to limitations of accuracy within internal processes, there may be

some discrepancy of positions between the mouse cursor and corrected

shape or one corner and the other 3 corners.

5. Press the ENTER button.

6. Use the SELECT ̆̄̇̈ button to move the projected image frame

as shown on the example.

7. Press the ENTER button.

When using the remote control or cabinet buttons:

Screen

1. Project an image so that the screen is smaller than the area of the

raster.

2. Pick up any one of the corners and align the corner of the screen

with the one of the image.

Projected image

8. Use the SELECT ̆̄̇̈ button to select another icon which points

in the direction.

Screen

On the Cornerstone adjustment screen, select

“Exit”and then“OK”, or press the CANCEL but-

ton on the remote control.

(The drawing shows the upper right corner.)

The confirmation screen is displayed.

3. Press the 3D REFORM button on the remote control.

9. Press the SELECT ̇ or ̈ button to highlight the [OK] and press the

ENTER button.

The CORNERSTONE adjustment screen is displayed.

This completes the keystone correction.

Selecting “Cancel” will return to the adjustment screen without saving

changes (Step 3).

Selecting "Reset" will return to the factory default.

Selecting "Undo" will exit without saving changes.

NOTE: Press the 3D REFORM button to toggle between "Cornerstone" and "Key-

stone."

NOTE: To return the 3D Reform correction setting values to the factory default,

press and hold the 3D REFORM button for a minimum of 2 seconds.

E-21

Download from Www.Somanuals.com. All Manuals Search And Download.

NOTE: During 3D Reform adjustment, "Aspect Ratio" and "Screen" may not be

available. Should this happen, first reset the 3D Reform data and then do each

setting. Second repeat the 3D Reform adjustment. Changing Aspect Ratio and/

or Screen setting can limit 3D Reform in its adjustable range.

Turning Up or Down Volume

Sound level from the speaker and the AUDIO OUT jack (RCA) on the

projector can be adjusted.

The adjustable ranges for 3D Reform are as follows:

Horizontal ........... Max 35° approx.

Vertical ............... Max +50°/-25° approx.

VOLUME

increase volume

The following are conditions at the above maximum angle when all of

the following are met

•

Image is projected in Wide (Zoom)

Resolution is XGA

decrease volume

Higher resolution than XGA limits 3D Reform in its adjustable range.

Menu items should be set as follows:

Aspect Ratio ............................... 4:3

Screen Type ................................ 4:3

Horizontal and Vertical are adjusted separately.

•

Volume bar

•

A combination of both adjustments limits 3D Reform in its adjustable

range.

When "4:3 Fill" is selected in Aspect Ratio, "Cornerstone" and "Hori-

zontal Keystone" are not available.

Optimizing RGB Picture Automatically

Adjusting the Image Using Auto Adjust

Using the Laser Pointer

Optimizing RGB image automatically

Press the Auto Adjust button to optimize an RGB image automatically.

You can use the laser to draw your audience's attention to a red dot that

you can place on any object.

[Poor picture]

Press and hold the LASER button to activate the laser pointer.

AUTO ADJ.

[Normal picture]

IDE

AUT

LASER

FREEZE

INTER

PIC-MUTE

MAGNIFY

FOCUS

FOLDER

SLIDE

CAUTION:

Press the Auto Adjust button to fine-tune the computer image or to re-

move any vertical banding that might appear and to reduce video noise,

dot interference or cross talk (this is evident when part of your image

appears to be shimmering). This function adjusts the clock frequencies

that eliminate the horizontal banding in the image. This function also

adjusts the clock phase to reduce video noise, dot interference or cross

talk. (This is evident when part of your image appears to be shimmer-

ing.)

• Do not look into the laser pointer while it is on.

• Do not point the laser beam at a person.

This adjustment may be necessary when you connect your computer

for the first time.

NOTE:

• Some signals may not be displayed correctly or take time.

• The Auto Adjust function does not work for component and video signal.

• If the Auto Adjust operation cannot optimize the RGB signal, try to adjust Clock

and Phase manually. See page E-39.

• Pressing and holding the AUTO ADJUST button on the cabinet or AUTO ADJ

button on the remote control for a minimum of 2 seconds will enable the Auto

Focus and the Wall Color Correction feature instead of the Auto Adjust feature.

E-22

Download from Www.Somanuals.com. All Manuals Search And Download.

Setting the function switch

There are two switches on the bottom of the battery case: an applicable

projector selector switch (1) and laser enable/disable switch (2). Check

the projector being used and decide whether to enable or disable laser,

then set these switches as necessary using the tip of a thin ball-point

pen. On this model, an applicable projector selector switch (1) is not

used.

OFF

Switch (2)

On:

Off:

Enabled (the laser lights when the LASER button is pressed)

[Factory default]

Disabled (the laser does not light even when the LASER but-

ton is pressed)

Disable the laser when using in an environment in which the unit is

accessible to children.

Turning off the Projector

OFF

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

To turn off the projector:

First press the POWER (ON/STAND BY) but-

ton on the projector cabinet or the POWER OFF

button on the remote control for a minimum of

two seconds. The power indicator will glow or-

ange. After the projector turns off, the cooling

fans keep operating for 90 seconds (Cooling-

off time).

ASPECT FREEZE 3D REFORM

Second, turn off the Main Power switch. The

power indicator will go out. Last unplug the

power cable.

HELP

POINTER PIC-MUTE

VOLUME MAGNIFY

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

LIST

CAUTION

Do not unplug the power cable from the

wall outlet or do not turn off the main power

under any one of the following circum-

stances. Doing so can cause damage to

the projector:

•

While the Hour Glass icon appears.

•

While the message "Please wait a mo-

ment." appears. This message will be

displayed after the projector is turned

off.

•

While the cooling fans are running. (The

cooling fans continue to work for 90 sec-

onds after the projector is turned off).

While accessing a PC card. (The PC Card

Access indicator lights.)

E-23

Download from Www.Somanuals.com. All Manuals Search And Download.

CONVENIENT FEATURES

When using the USB Port

Using the Remote Mouse Function

For PC, the mouse receiver function can only be used with a Windows

98, Windows ME, Windows XP or Windows 2000 operating system.

The built-in remote mouse function enables you to operate your

computer's mouse functions from the remote control (Computer mode).

It is a great convenience for clicking through your computer-generated

presentations.To return to the projector operation mode (Projector mode),

press the PJ button (lit red).

USB port (PC)

Connecting to your computer for the remote mouse

function

If you wish to use the remote mouse function, use the supplied USB

cable to connect the USB port (PC) of the projector and the USB port

(type A) of your computer.

NOTE: Depending on the type of connection or OS installed on your computer,

you may have to restart your computer or change you computer settings.

USB port

(Type A)

NOTE: Wait at least 5 seconds after disconnecting the USB cable before recon-

necting it and vice versa. The computer may not identify the built-in mouse re-

ceiver if it is repeatedly connected and disconnected in rapid intervals.

Switching operation mode between computer and projector

The three shaded buttons shown on the drawing work as a computer mouse in the Computer mode.

In the Computer mode the PJ button is not lit.

Works as a mouse for your computer.

Works as the SELECT button on the projector.

OFF

POWER

RGB

POWER

RGB

VIDEO

AUTO ADJ.

VIEWER

LASER

VIDEO

AUTO ADJ.

VIEWER

LASER

Works as a right-click button

for your computer.

Works as the CANCEL

button on the projector.

Lit red

Not lit

ASPECT FREEZE 3D REFORM

HELP

POINTER PIC-MUTE

HELP

POINTER PIC-MUTE

Works as the ENTER

button on the projector.

VOLUME MAGNIFY

SLIDE

VOLUME MAGNIFY

SLIDE

Works as a left-click

button for your com-

puter.

ZOOM

FOCUS

FOLDER

SLIDE

ZOOM

FOCUS

FOLDER

SLIDE

LIST

•

When the MENU button is pressed, the PJ button lights red to indicate that you are in the Projector mode, which allows the projector menu

operation using the three buttons.

When the POINTER button is pressed, the PJ button lights red to indicate that you are in the Projector mode and that the SELECT ̆̄̇̈

button works as a moving button for the POINTER or magnified image.

If no buttons are pressed within 60 seconds, the PJ button's light goes out to indicate that you are in the Computer mode.To enable the projector

menu operation again, press the PJ button to light red.To move the pointer or a magnified image again, turn off the pointer and then turn on the

pointer (press the POINTER button two times).

•

When the PJ button is lit, if you want to use the mouse function immediately, press the PJ button to return to the Computer mode (not lit).

During Computer mode:

In Computer mode, by pressing the ENTER button for 2 seconds or more then releasing, the drag mode is set and the drag operation can be

performed simply by pressing the SELECT ̆̄̇̈ (mouse) button. To drop the item, press the ENTER (left click) button again or press the

CANCEL (right click) button.

E-24

Download from Www.Somanuals.com. All Manuals Search And Download.

Turning Off the Image and Sound

Enlarging and Moving a Picture

Press the Picture Mute button to turn off the image and sound for a

short period of time. Press again to restore the image and sound.

You can enlarge the area you want up to 400 percent.

To do so:

PIC-MUTE

1. Press the Pointer button to display the pointer.

POINTER

Freezing a Picture

Press the Freeze button to freeze a picture. Press again to resume

motion.

FREEZE

2. Move the pointer to the area you want to enlarge.

Using the Pointer

SELECT

You can use one of eight pointers to draw your audience's attention to

the portion of a projected image you want.

POINTER

3. Enlarge the selected area.

When the Magnify (+) button is pressed, the image is magnified. To

move the magnified image, use the SELECT button.

MAGNIFY

Press the Pointer button to dis-

play the pointer.

Press the Pointer button to display the pointer.

4. Return the image to the original size.

MAGNIFY

SELECT

Use the Select button to move

the pointer.

Use the Select button to move the pointer.

Getting the On-line Help

You get the contents about Help.

HELP

SELECT

Display Help

Exit Help

E-25

Download from Www.Somanuals.com. All Manuals Search And Download.

Using the USB Mouse

Using the USB HUB Function

Using the supplied USB mouse gives you a smooth operation. A com-

mercially available USB mouse can be also used.

When using the projector with a PC via the supplied USB cable, both

the USB port(type A) on the projector can be connected to a USB-sup-

ported scanner or other USB-supported device. (USB Hub Function)

(

)

Example: When connecting a PC and a scanner to each USB port re-

spectively

USB MOUSE/HUB

(

)

(

)

USB MOUSE/HUB

USB PC

NOTE: There may be some brands of USB mouse that the projector does not

support. The scroll button on the supplied USB mouse does not work with the

projector.

An example of how a scanned image is projected

1. Install the Dynamic Image Utility on your PC.

Operate the Menus using the USB mouse

NOTE: The Dynamic Image Utility is contained on the supplied CD-ROM. See

the supplied NEC Software Utility Installation Guide for the installation proce-

dure.

Mouse Cursor

When connecting a USB mouse to the projector, you get a mouse

cursor on the screen.

Unless you use your USB mouse within 10 seconds, the mouse cur-

sor disappears.

2. Use your scanner to scan an image.

NOTE: A scanner driver must be installed on your PC before use.

Menu Display

Clicking with a mouse button displays the menu.

Clicking ̈ displays the pull-down menu. To close the menu, click

anywhere in the background.

3. Load the scanned image on your PC using the Dynamic Image Util-

ity.

4. Transmit the scanned image from your PC to the projector via the

USB cable and project the image on the screen.

Adjusting and Setting Display

You can select a menu item and click with a mouse button to make

adjustments and setting.

NOTE:

•

The USB HUB function is effective only when “Auto” is selected in Operation

Mode Select.

The PCs using the USB Host Controller may not be available.

When connecting a USB hub to the USB port (type B) on the projector, be

sure to use a USB hub capable of supplying 500mA per port of downstream

current.

Examples

Click (or press and hold) the mouse button ̇ or ̈ to adjust the bright-

ness.Or click and drag the mouse button on the slide bar horizontally

to adjust it.

•

To save the adjustments, click

. The display is closed. If you click

anywhere in the background while displaying adjustment and setting

menu or dialog box, you will get the main menu at the clicking point.

E-26

Download from Www.Somanuals.com. All Manuals Search And Download.

Changing Background Logo

Making Freehand Drawings on a Projected

Image (ChalkBoard)

You can change the default background logo using the PC Card Files

feature.

The ChalkBoard feature allows you to write and draw messages on a

projected image.

NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP

are not available.

NOTE: The ChalkBoard feature is available only when a USB mouse is used.

1. From the menu, select [Tools] → [PC Card Files] to display a list of all

the files stored in the PC card so that you can select a file you want to

use as a background logo.

From the menu, select [Tools] → [ChalkBoard] to display the ChalkBoard

tool bar that contains the following icons.

Eraser

Drive

Pen

Exit

Drag

Color

Clear

Hide

Capture

Drag ............ Drags to move the tool bar by clicking on the blue part.

(for USB mouse operation only)

Pen .............. Left-click and drag to draw. Left-click [̆] or right-click the

pen icon to display the pen palette containing four lines of

different thickness from which you can select a line you

prefer by left-clicking.

Color ........... Selects a color. Left-click to display the color palette from

which you can select a color you prefer by left-clicking.

Capture ....... Left click to capture and save freehand drawings in the

PC card.

Eraser ......... Left-click and drag to erase part of a drawing. Left-click

[̆] or right-click the eraser icon to display the eraser pal-

ette containing four eraser of different thickness from which

you can select an eraser you prefer by left-clicking.

Clear ........... Left-click to clear the drawing completely from the

ChalkBoard screen.

2. The Logo button allows you to select a background logo from graphic

files on a PC card and change to it as the background logo.

3. Use the SELECT ̆ or ̄ button to select a JPEG or BMP file for your

background logo.

4. Use the SELECT ̈ and then ̄ button to select "Logo".

5. Press the ENTER on the remote control or the cabinet. You will get

the confirmation dialog box.

6. Select "OK" and press the ENTER button. This completes changing

a logo for the background.

Drive ............ Switches between PC Card slot 1 and 2.

Hide ............. Hides the tool bar by left-clicking. Right-clicking anywhere

on the screen displays the ChalkBoard tool bar again.

Exit .............. Clears the complete drawing and exits the ChalkBoard.

NOTE:

• The menu is not available while you display the ChalkBoard screen.

• Switching slides clears a drawing completely.

Once you have changed the background from the NEC logo to an-

other, you cannot return the logo to background even by using Fac-

tory Default. To do so, repeat the above steps. The NEC logo file is

included on the supplied CD-ROM NEC Projector User Supportware

(/Logo/nec_bb_x.jpg).

E-27

Download from Www.Somanuals.com. All Manuals Search And Download.

USING THE VIEWER

Inserting and Removing a PC Card

NOTE:

•

To use the Viewer, first you need to create presentation materials on your PC

using the Dynamic Image Utility 2.0 contained on the supplied NEC Projector

User Supportware CD-ROM. For installation, see the printed NEC Software

Utility Installation Guide. For creating presentation materials, see the Slide

show function on the on-line manual of the Dynamic Image Utility 2.0.

NOTE:

•

Do not try to force the PC card into the slot.

A dummy card is inserted into each slot at the time of shipment. First remove

the dummy cards before use.

•

Selecting Viewer sets the audio input for DVI input.

Making the Most out of the Viewer Function

Features

You can view presentation data, capture, and play images on the pro-

jector. A PC card is used to view presentation data prepared on the

computer and to capture and play images projected with the projector.

The Viewer feature allows you to view slides stored on a PC memory

card (referred to as PC card in this manual) on the projector. Even if no

computer is available, presentations can be conducted simply with the

projector. This feature is convenient for holding presentations at meet-

ings and in offices, as well as for playing images taken on digital cam-

eras.

Inserting the PC Card

•

Hold the PC card horizontally and insert it slowly into PC card

slot 1 or 2 with its top facing up.

•

The eject button pops out once the PC card is fully inserted.

Check that the PC card is fully inserted.

PC card (not supplied)

Easy to use

•

Presentations can be started immediately simply by inserting a

PC card (not supplied)

•

Easy slide switching

REMOTE

)

E/H

Remote control operation

(

Jumping to list of slides or any specific slide

High quality images

VIDEO IN

•

High resolution up to 1024 x 768 dots

24-bit full color playback

Removing the PC Card

Press the eject button.The PC card pops out a little.Grasp the edges

of the PC card and pull it out.

Viewing of digital camera images

Simple utility software (for computer)

•

Dynamic Image Utility 2.0 operable on Windows 98/Me/XP/2000

NOTE: Do not eject the PC card while its data is being accessed.

Slides can be created by capturing the currently displayed im-

age

Eject button

•

Control screen for displaying lists of slides and editing

Microsoft, Windows and PowerPoint are registered trademarks

of Microsoft Corporation.

PC CONTROL

)

MOUSE/HUB

(

USB

L/MONO

AUDIO

B/Cb

DVI IN

AUDIO OUT

G/Y

AUDIO

AC IN

RGB OUT

RGB2 IN

RGB1 IN

AUDIO

ONO

L/M

AUDIO

L/MONO

AUDIO

-VID

Direction for Inserting the PC Card

The PC card has a top and bottom and must be inserted into the PC

card slot in a specific direction. It cannot be inserted backwards or up-

side-down. Attempting to force it into the slot in the wrong direction may

break the internal pin and damage the card slot. Refer to the PC card's

operating instructions for the proper direction of insertion.

PC Card Type

The PC Card slot accepts PCMCIA Type II only.

E-28

Download from Www.Somanuals.com. All Manuals Search And Download.

When the tool bar is not displayed:

Operating the Viewer Function from the

Projector (playback)

Press the FOLDER LIST button or the SLIDE LIST button on the re-

mote control to display folders or from a PC card in the projector's PC

Card slot.

This section describes the operation for showing slides of presentation

documents created using the Viewer function with the projector. It is

also possible to make slides directly from the images projected with the

projector.

FOLDER

Projecting slides (Viewer)

1. Insert a PC card into the PC card slot.

Insert the PC card so that the end with the insertion direction arrow

on the top goes in first.

Multi cursor (blue marks)

Press the eject button to eject the card.

Folder

2. Select the "Viewer" from the Source Select menu.

3. Project slides.

Checking "Show Folder List", means that selecting Viewer input dis-

plays a list of the folders in the PC card and if "Auto Play" is checked the

projector automatically starts to play slides at the first slide of the folder

you have selected.

02 : 0001 / 0008

Current folder number

A tool bar will appear when you press the MENU button on the remote

control or the projector cabinet or clicking with the right button of a mouse.

Number of all slides in

folder

Current slide

number

Delete

Play

Jump

Drive

Use the SLIDE +/- button to advance to the next folder or return to the

previous folder.

Drag

View

Setup

Stop

Select

SLIDE

The tool bar includes the following buttons:

Folder

Drag ............ Drags to move the tool bar.This is available for USB mouse

operation only.

Prev ............. Returns to the previous slide or folder. Or this lets you

play slides back in reverse.

Next ............. Advances to the next slide or folder. Or this lets you play

slides back.

Play ............. Plays back automatically or manually depending on the

setting on Viewer Options of the menu.This allows you to

move on to the next slide when "Manual Play" is selected.

Use the SLIDE +/- button to advance to the next slide or return to the

previous slide.

Stop............. This allows you to stop Auto Play while you are playing

back and to resume playing from the selected slide or folder

when "Auto Play" is selected.

Slide(Table) cursor

(green marks)

Slide

Jump ........... Displays a list of slides while you are playing back.

Select .......... Displays a list of folders while you are playing back.

Drive ............ Switches between PC Card slot 1 and 2.

Setup........... Displays the Viewer Options dialog box on Page 2 of the

Setup dialog box.

Delete.......... Deletes a captured slide(s) or all the captured slides in

the Capture - specific folder.

02 : 0004 / 0008

View ............ Hides the tool bar while you are playing back. Pressing

the MENU button or clicking with the right button of a

mouse shows it again.

NOTE: If no memory card is inserted in the PC CARD slot, there is no signal, and

a black, blue or logo background is displayed, depending on the setting.

Playback is stopped when SLIDE +/- button on the remote control or ̇̈ button

on the cabinet is pressed in Auto Play mode.

Up to 12 indexes can be displayed on the list of folders. The folder in the right

bottom is always a folder exclusively for captured images, but is only displayed

when images have been captured.

E-29

Download from Www.Somanuals.com. All Manuals Search And Download.

Preparations:

NOTE: You can also use the ̇ and ̈ button on the remote control to select

folders or slides.

If you use the ̇ and ̈ button on the remote control for Viewer operation, press

the PJ button to switch to the Projector mode and the PJ button lights red.

Insert the PC card into the card slot.

Insert the PC card so that the end with the insertion direction arrow

on the top goes in first.

* Press the eject button to eject the card.

1. Project the image you wish to store on the projector.

2. Select the "Capture" from the Tools menu.

Works as the Select button on the

projector.

SELECT

Lit red

3. A tool bar will appear.

Auto Play Mode

If the "Auto Play" option is selected in "Viewer Options" of the menu,

any given slide will start to play automatically.

You can also specify Auto Play Interval between 5 and 300 seconds.

Capture

Drag

Freeze

Exit

Switching to Slides Directly from Other Input Modes

Drive

The tool bar includes the following buttons:

With this function it is possible to switch directly to a slide when the

picture of a VCR or computer is being projected.

Example:When conducting presentations using a combination of slides

and moving pictures from a VCR, etc., it is possible to switch from a

Viewer slide to the video picture then back to the Viewer slide simply by

using the Viewer button.

Drag ............ Drags to move the tool bar by clicking on the blue part (for

USB mouse operation only).

Capture ....... Captures an image and save it as a JPEG file on a PC

card.

NOTE: Even if you switch the current Viewer source to another source, the cur-

rent slide is retained. When you return back to the Viewer, you will get the slide

that has been retained.

Freeze ......... Freezes and unfreezes images.

Drive ............ Switches between PC Card slot 1 and 2.

Exit .............. Exits the Capture function. Another option to exit the Cap-

ture function is to press MENU or CANCEL button on the

remote control or projector cabinet.

The PC card editing operation cannot be performed from the projector.

Do so using the Dynamic Image Utility 2.0 software.

Viewing Digital Images

NOTE:

You can compress a captured file (JPEG) using the Capture Options in the Setup

dialog. See page E-44.

Digital images can be played with the Viewer if the following conditions

are met:

Captured images with higher resolution than the projector's native resolution

cannot be displayed correctly.

•

If the image can be stored on an MS-DOS format PC card

If the image can be stored in a format supported by the Viewer. With

the Viewer, images on the card are searched for in directories and

images in JPEG or BMP format are recognized as slides.Searchable

directories are directories within two steps from the root directory,

and searchable images are images within the first 12 files in the di-

rectory. Only file and slide switching are possible.

• File size of the captured image varies depending on the resolution of an input

signal.

• An hourglass indicating that an image is being captured appears on the

projector's display. Do not eject the PC card or turn off the projector's power

while this icon is displayed. Doing so will damage the PC card data. If the PC

card data is damaged, use a computer to repair the data.

• Up to 12 indexes can be displayed on the list of folders. The folder in the right

bottom is always a folder exclusively for captured images, but is only dis-

played when images have been captured.

NOTE: The maximum number of images recognized as slides within one direc-

tory is 128.

Storing Images Displayed on the Projector on the PC

card (Capture)

The Capture features allows you to capture an image from a source that

is currently being displayed. The image is saved as JPEG in the PC

card. When you select Capture from the menu, you will get a tool bar.

You can capture an image directly using the tool bar when the menu is

not displayed.

NOTE:

* Unless a PC card is inserted into the PC Card slot of the projector, the Capture

feature is not available.

* The "Card Error" display means that the free space of the PC card is insufficient

for saving images. Make more space available on the card by erasing un-

wanted images with your PC. The number of images that can be captured

depends on the size of the PC card.

* Be sure not to turn off the power or remove the PC card while capturing an

image. Doing so could cause a loss of the data in the PC card or damage to the

card itself.

E-30

Download from Www.Somanuals.com. All Manuals Search And Download.

Deleting Captured Images

Using the Delete button on the tool bar for Viewer can delete captured

images.

Delete

Play

Jump

Drive

Drag

View

Setup

Stop

Select

To delete captured images:

1. Select Viewer and display a folder list of captured images.

2. Use button to select the Capture folder [Cap] in the right bottom of

the screen.

3. Press the MENU button to display the tool bar.

4. Use the ̇ or ̈ button to select the Delete icon and press the EN-

TER button or click with a mouse button.

Using the PC Card Files Fucntion (PC Card Files)

The PC Card Files function allows you to display a list of all the files

stored in the PC card so that you can select a file you want to display.

You can also sort files by file name or date, or display the file. Although

a list of all the files in the PC card is displayed, you can view files in idx,

text, HTML, JPEG and BMP format only. Selecting BMP and JPEG files

automatically switches to the Viewer source. See also page E-37.

NOTE: This option is not available for selection unless a PC card is inserted

properly.

Selecting "Execute" displays the file you selected.

When you select a JPEG or BMP file and press the ENTER button on

the remote or the cabinet, or "Execute" on the above, you will get a

toolbar. This toolbar is used to return to the PC Card Files screen.

Drag

Return

Drag ............ Drags to move the tool bar. (for USB mouse operation

only)

Return ......... Returns to the PC Card Files screen.

Close ........... Close the toolbar.

E-31

Download from Www.Somanuals.com. All Manuals Search And Download.

USING ON-SCREEN MENU

The default Custom Menu items are:

Basic Menu Operation

Source Select (RGB 1/2, Video, S-Video, DVI(DIGITAL), Viewer and

LAN), Picture, Sound, Image Options (Aspect Ratio), Picture Manage-

ment, Projector Options (3D Reform, Menu, Setup, Lamp Setting, Screen

and LAN Mode), Tools (Sleep Timer, Capture, PC Card Files and

ChalkBoard) and Help (Contents and Information).

Using the Menus

NOTE: The on-screen menu may not be displayed correctly while interlaced mo-

tion video image is projected.

1. Press the MENU button on the remote control or projector cabinet to

display the Basic, Advanced or Custom Menu.

NOTE: Once you have selected OK on the Custom Menu Edit screen, you cannot

cancel the changes on the Menu screen. However, you can reedit the menu items

over again as described in the steps above.

NOTE: When using a USB mouse, click the mouse button to display the menu.

For other operations, do the same way as you use your PC mouse.

2. Press the SELECT ̆̄ buttons on the remote control or the projec-

tor cabinet to highlight the menu for the item you want to adjust or

set.

NOTE: If the "Advanced Menu" item has been selected on the Menu mode, you

get the "Confirmation Change Menu" upon completion of "Custom Menu" editing.

In this case, selecting "Yes" then "ENTER" will close all the menus and apply the

changes from the Advanced menu to the Custom Menu. If you select "No" then

"ENTER" functions, then all menu items will return to the Advanced menu, but

your changes will still be available within the "Custom Menu" selection. To dis-

play the previously tailored Custom Menu, select "Custom Menu" from the "Menu

Mode".

3. Press the SELECT ̈ button or the ENTER button on the remote

control or the projector cabinet to select a submenu or item.

4. Adjust the level or turn the selected item on or off by using SELECT

̇ or ̈ buttons on the remote control or the projector cabinet.

The on-screen slide bar will show you the amount of increase or

decrease.

An item "To Advanced Menu" will be added to the bottom of the Custom

Menu.

5. Changes are stored until you adjust it again.

Selecting this item and pressing the ENTER button will display the "Ad-

vanced Menu" features.

ENTER .......... Stores the setting or adjustments.

CANCEL ........ Return to the previous screen without storing settings

or adjustments.

NOTE: You can close the main and sub menus simultaneously by pressing

the PJ button on the remote control to cancel the Projector mode.

6. Repeat steps 2-5 to adjust an additional item, or press the CANCEL

button on the projector cabinet or the remote control to quit the menu

display.

Customizing the Menu

The Custom menu can be customized to meet your requirements. Se-

lecting a menu item from the "Custom Menu Edit" list, allows you to

custom tailor the menu items to your needs.

1. Select "Custom Menu Edit" to display the "Custom Menu Edit" screen.

2. Use the SELECT ̆ or ̄ buttons to highlight your selection and press

the ENTER button to place a check mark next to an option.

This action enables that feature. Press the ENTER button again to

clear the check box.

If you select an item with a solid triangle ̈ and press the ENTER

button on the remote control or the projector cabinet, you can enable

all the items within that submenu. Also you can turn on an item within

the submenu without placing a check mark on the main menu item.

NOTE: Up to 12 main menu items (within Custom Menu Edit, not including

submenu items) can be selected.

3. In order for the changes to take effect, use the SELECT ̇ or ̈ but-

ton on the remote control or the projector cabinet to highlight "OK",

then press the ENTER button. To cancel the changes, use the SE-

LECT ̆ or ̄ buttons to highlight "Cancel" and press the ENTER

button.

To return to the factory default, select "Reset" then press the ENTER

button.

E-32

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu tree

Advanced Menu

RGB1

Source Select

Picture

RGB2

Video

Sound

S-Video

DVI (DIGITAL)

Viewer

LAN

Image Options

Picture Management

Projector Options

Tools

User1

User2

User3

Entry List

Help

Factory Default

Picture

Brightness, Contrast, Color,

Hue, Sharpness

Volume, Bass, Treble

Aspect Ratio

4:3, Letterbox, Wide Screen, Crop / 4:3

Window, Letterbox, Wide Screen, 4:3 Fill

Top, Bottom, Left, Right

Horizontal, Vertical, Clock, Phase

Auto, Native

Blanking

Position/Clock

Resolution

Overscan

0%, 5%, 10%, 25%

Video Filter

Noise Reduction

Signal Type

Off, Less, More

Off, Low, Medium, High

RGB, Component

Picture Management

Presentation, sRGB, Graphic, Video,

Movie, User 1, User 2, User 3, User 4

E-33

Download from Www.Somanuals.com. All Manuals Search And Download.

Advanced Menu

Source Select

Picture

Cornerstone

Keystone

Horizontal, Vertical

Sound

Off, User 1, User 2, User 3, User 4 (Auto Adjust Button)

Image Options

Picture Management

Projector Options

Tools

3D Reform

Wall Color Correction

Setup

Page 1

Help

Lamp Setting

Screen

Language

English, Deutsch,

Français, Italiano,

Español, Svenska

Factory Default

Auto Functions

LAN Mode

Password

Security

Menu Mode

Projector Pointer

Basic Menu,

Custom Menu,

Advanced Menu

Custom Menu Edit

Pointer 1-8

Setup

Page 1

Menu Display Time Manual, Auto 5sec,

Auto 15sec,

Orientation

Desktop Front, Ceiling Rear,

Desktop Rear, Ceiling Front

Blue, Black, Logo

Auto 45sec

Background

Page 2

RGBOUT Terminal Last, RGB1, RGB2

Source Display

Message

On, Off

Closed Caption

Off, Caption1-4, Text1-4

Page 2

Menu Color Select Color, Monochrome

Viewer Options

Show Folder List

Auto Play, Manual Play, Interval

High Quality, Normal,

High Compression

Capture Options

Mouse Button

Right Hand, Left Hand

Sensitivity Fast, Medium, Slow

Operation Mode Select Auto, Projector

Page 3 Signal Select

RGB1 RGB/Component, RGB, Component, Scart

RGB2 RGB/Component, RGB, Component, Scart

Video, Auto, PAL-M/PAL-N/NTSC3.58, NTSC3.58,

S-Video NTSC4.43, PAL, PAL-M, PAL-N, PAL60, SECAM

Page 4

Auto Adjust, Auto Start, Power Management,

Power Off Confirmation, 3D Reform Save,

High Speed Fan Mode, Built-in Speaker, Idle Mode,

Clear Filter Usage Meter

Page 5

Remote Sensor

Front, Back, Left, Right

S-Video Mode Select Off, S2

Page 6

Communication Speed

Default Source Select

4800, 9600, 19200, 38400

Last, Auto, Select (RGB1, RGB2,Video,

S-Video, DVI(DIGITAL), Viewer, LAN)

Enable, Disable

Control Panel

Key Lock

E-34

Download from Www.Somanuals.com. All Manuals Search And Download.

Lamp Mode

Lamp Type

Normal, Eco

Standard Lamp,

Extended Life Lamp

Advanced Menu

Source Select

Picture

Screen Type 4:3, 16:9 / Position

3D Reform

Wall Color Correction

Focus

On, Off

Volume

Wall Color Correction

Image Options

Picture Management

Projector Options

Tools

Setup

LAN Mode

IP Address

Automatic

Manual

Lamp Setting

Screen

Help

Auto Functions

LAN Mode

Password

Security

IP Address,

Factory Default

Subnet Mask,Gateway

Projector Name

DNS Configuration

Domain Name

Network Type

Mode

Infrastructure,

802.11 Ad Hoc, Ad Hoc

Easy Connection

SSID

Channel

TX rate

1-14

Sleep Timer

Automatic, 11M, 5.5M, 2M,

1M, 1M-2M-Automatic

Capture

PC Card Files

ChalkBoard

WEP

Disable, 64bit, 128bit

Key1-4

Key Select

Key1-4

Contents

Information

Mail

Alert Mail

Sender's Address

SMTP Server Name

Recipient's Address 1

Recipient's Address 2

Recipient's Address 3

Test Mail

Factory Default

All Data,

Current Signal

Status

IP Address

Subnet Mask

MAC Address

Logo

Security

Enable, Disable, Keyword,

Use Protect key, Drive, Read,

E-35

Download from Www.Somanuals.com. All Manuals Search And Download.

Menu Elements

Highlight

Help Button

Close Button

Title bar

Tab

Radio button

OK Button

Cancel Button

Solid triangle

Check box

Slide bar

Drag

Tool bar

Menu windows or dialog boxes typically have the following elements:

Cancel button ..... Press to cancel your setting. You will return to the

previous menu.

Title bar .............. Indicates the menu title.

Close button ....... Click to close the window with saving changes. (USB

mouse only)

Highlight ............. Indicates the selected menu or item.

Solid triangle ...... Indicates further choices are available. A highlighted

triangle indicates the item is active.

Help button ......... Indicates that help about that feature is available (USB

mouse only). Press the Help button on the remote

control to display help.

Tab ..................... Indicates a group of features in a dialog box. Select-

ing on any tab brings its page to the front.

Toolbar ............... Contains several icons for specific tasks. It is also

referred to as “launcher”.

Radio button ....... Use this round button to select an option in a dialog

box.

Drag ................... Point the mouse here, and click and drag to move a

toolbar.

Check box .......... Place a checkmark in the square box to turn the op-

tion On.

Slide bar ............. Indicates settings or the direction of adjustment.

OK button ........... Press to confirm your setting. You will return to the

previous menu.

E-36

Download from Www.Somanuals.com. All Manuals Search And Download.

Delete

Entering Alphanumeric Characters by Using the Menu

Play

Jump

Drive

Alphabet or numeric characters are used for your IP address or projec-

tor name.To enter IP Address or projector name, use the software key-

board.

Drag

For using the software keyboard, see page E-60.

View

Setup

Stop

Select

Drag ............... Drags to move the tool bar. (for USB mouse opera-

tion only)

Prev ............... Returns to the previous slide or folder.

Next ............... Advances to the next slide or folder.

Play ................ Plays back automatically or manually depending on

the setting on Viewer Options of the menu. This al-

lows you to move on to the next slide when "Manual

Play" is selected.

Stop ............... Stops Auto Play while you are playing back and to

resume playing from the selected slide or folder when

"Auto Play" is selected.

Jump .............. Displays a list of slides while you are playing back.

Select ............. Displays a list of folders while you are playing back.

Drive .............. Switches between PC Card slot 1 and 2.

Setup ............. Displays the Viewer Options dialog box on Page 2 of

the Setup dialog box.

Delete ............ Deletes a captured slide(s) or all the captured slides

in the selected folder.

View ............... Hides the tool bar while you are playing back. Click-

ing with the right button of a mouse shows it again.

Provides access to controls for your image. Use the

SELECT button on the projector cabinet or the re-

mote control to highlight the menu for the item you

want to adjust.

Menu Descriptions & Functions

Source Select

Selecting a Source

Enables you to select a video source such as a VCR, DVD player, laser

disc player, computer or document camera depending on what is con-

nected to your inputs. Press the SELECT ̆̄ button on the projector

cabinet or on your remote control to highlight the menu for the source

you want to project.

LAN

Selects a signal from a LAN card plugged into the projector's card

slot.

Entry List

RGB

Selects the computer connected to your RGB1, RGB2 or component

signal.

NOTE: An optional component cable (Component V or ADP-CV1 cable) is

needed for a component signal.

Video

Selects what is connected to yourVideo input-VCR, laser disc player,

DVD player or document camera.

S-Video

Selects what is connected to your S-Video input-VCR, DVD player,

or laser disc player.

Displays the list of the entry signals. Use the SELECT ̆̄ buttons on

your remote control or the projector cabinet to select the signal and

press the ENTER button on the remote control or the projector cabi-

net to display the Entry Edit Command screen.

NOTE: A frame may freeze for a brief period of time when a video is played

back in fast-forward or fast-rewind with a Video or S-Video source.

DVI (DIGITAL)

Selects the computer connected to the DVI input connector.

Using the Entry List

Making any ajustments to the current picture will automatically regis-

ter its adjustments to the Entry List. The registered signal can be

loaded any time from the Entry List.

Viewer

This feature enables you to make presentations using a PC card that

contains captured images and slides created with the exclusive Dy-

namic Image Utility 2.0 contained in the CD-ROM. See the supplied

Software Utility Installation Guide for installing the Dynamic Image

Utility 2.0.The starting screen for theViewer varies depending on the

settings of the Setup's Page 2. See Setup on page E-44.

NOTE: Up to 100 presets can be registered.

NOTE: Even if you switch the current Viewer source to another source, the

current slide is retained. When you return back to the Viewer, you will get the

slide that has been retained. A launcher will appear when you press the MENU

button.

A press of the MENU button displays the toolbar;a press of the MENU

button again displays the Menu and hereafter each press of the MENU

button switches displaying between the Menu and the toolbar.

The launcher is a tool bar including the following buttons:

E-37

Download from Www.Somanuals.com. All Manuals Search And Download.

Entry Edit Command

Picture (not available for Viewer and LAN)

Adjusting Brightness, Contrast, Color, Hue, and Sharpness

Brightness ...... Adjusts the brightness level or the back raster inten-

sity.

Contrast ......... Adjusts the intensity of the image according to the

incoming signal.

Color .............. Increases or decreases the color saturation level (not

valid for RGB).

You can edit signals on the Entry List.

Load ............... Enables you to select a signal from the list.

Hue ................ Varies the color level from +/- green to +/-blue. The

red level is used as reference.This adjustment is only

valid for Video and Component inputs (not valid for

RGB).

Store .............. Enables you to store the currently projected signal.

Cut ................. Enables you to remove a selected signal from the list

and place it on the "clipboard" in the projector.

Copy .............. Enables you to copy a selected signal from the list

and place it on the "clipboard" in the projector.

Sharpness ..... Controls the detail of the image for Video (Not valid

for RGB).

Paste .............. Enables you to paste the signal placed on the "clip-

board" to any other line of the list. To do this, select

"Paste" and then select the line number you want to

paste to. Last press ENTER.

Sound

Controllling Volume, Bass and Treble.

Adjusts the sound, bass and treble level of the projector speaker and

AUDIO OUT (RCA).

Edit ................ Enables you to change source names or add source

names to "More" in the Sorce Select.

Source Name .. Enter a signal name.Up to 18 alpha-

numeric characters can be used.

Image Options

Selecting Aspect Ratio (not available for Viewer and LAN)

Aspect Ratio allows you to select the best Aspect mode to display your

source image.

When screen size 4:3 is selected for the source, the following selections

will display:

Input Terminal .. Change the input terminal. RGB1

and RGB2 are available for RGB sig-

nal;Video and S-Video are available

for composite signal.

Source List ...... Set signal selection method.

Lock ................ Set so that the selected signal can-

not be deleted when "All Delete" is

executed.

4:3.................. Standard 4:3 aspect

Letter Box ...... Reduced to display the true aspect with black bor-

ders on top and bottom

Skip ................. Set so that the selected signal will

be skipped during auto search.

Wide Screen .. Left & Right stretched with black borders on top and

bottom

When complete, select OK and press ENTER.To exit

without storing setting, select Cancel.Select "Source

Name" and press ENTER to display the Source Name

Edit window. You can change source name on this

window. Press [̄] to display the software keyboard,

which you can enter alphanumeric characters. See

page E-60 for the key function of the software key-

board.

Crop ............... Left & Right streched.

Left & Right sides cut. Available for 4:3 only.

When screen size 16:9 is selected for the source, the following selec-

tions will display:

4:3 Window .... Reduced to display the true aspect with black bor-

ders on right and left

All Delete ....... This feature enables you to delete all the registered

signals in the Entry List.

Letter Box ...... Standard 16:9 aspect

Wide Screen .. Left and right streched to display the true aspect

4:3 Fill ............ Stretched to display in 16:9 aspect ratio

The following buttons are not available for the currently projecting

signals:

1) The Cut and Paste buttons on the Entry Edit Command screen

2) The Input Terminal button on the Entry Edit screen

NOTE: You can adjust image positions vertically for source with black borders.

See page E47 for setting image positions.

Please note that using this projector for the purpose of commercial gain or the

attraction of public attention in a venue such as a coffee shop or hotel and em-

ploying compression or expansion of the screen image with a "Aspect Ratio" or

"Screen" setting may raise concern about the infringement of copyrights which

are protected by copyright law.

NOTE: During 3D Reform adjustment, "Aspect Ratio" may not be available.

Should this happen, first reset the 3D Reform data and then do setting again.

Second repeat the 3D Reform adjustment.

Changing the aspect ratio can limit 3D Reform in its adjustable range.

Input

Signal

Screen

Type

Letterbox

Squeeze

4:3

Crop

Wide Screen

4:3 Screen

Letterbox

16:9 Screen

Wide Screen

4:3 Fill

4:3 Window

E-38

Download from Www.Somanuals.com. All Manuals Search And Download.

Masking Unwanted Area (Blanking)

This feature allows you to mask any unwanted area of the screen

image.

Selecting Noise Reduction Level (not available for RGB, Viewer and LAN)

Select one of the three levels for reducing video noise: Low, Medium

or High.

Adjust the Top, Bottom, Left or Right blanking with the SELECT ̇ or

̈ button.

NOTE: The lower the Noise Reduction level, the better the image quality by

way of higher video bandwidth.

Adjusting Position and Clock

This allows you to manually adjust the image horizontally and verti-

Signal Type

cally, and adjust Clock and Phase.

Select either the RGB signal type or the Component signal type.

Horizontal/Vertical Position:

RGB ............... RGB signal

Adjusts the image location horizontally and vertically using the SE-

LECT ̇ and ̈ buttons.This adjustment is made automatically when

the Auto Adjust is turned on. See "Auto Adjust" on page E-45 for

turning on or off the Auto Adjust feature.

Component .... Component signals such as Y/Cb/Cr, Y/Pb/Pr

NOTE: This feature is available on RGB 1 and 2 only. If you do not get a better

picture even when you set "Signal Select" to "Component" in Setup, set this to

"Component".

Clock .............. Use this item to fine tune the computer image or to

remove any vertical banding that might appear. This

function adjusts the clock frequencies that eliminate

the horizontal banding in the image.

Picture Management

Press the SELECT ̇ and ̈ buttons until the band-

ing disappears. This adjustment may be necessary

when you connect your computer for the first time.

This adjustment is made automatically when the Auto

Adjust is turned on.

Phase ............ Use this item to adjust the clock phase or to reduce

video noise, dot interference or cross talk. (This is

evident when part of your image appears to be shim-

mering.) Use the SELECT ̇ and ̈ buttons to adjust

the image.

Use "Phase" only after the "Clock" is complete. This

adjustment is made automatically when the Auto Ad-

just is turned on.

This option allows you to adjust neutral tint for yellow, cyan or magenta.

There are 5 factory presets optimized for various types of images, or

you can set 4 user adjustable settings.

Selecting Resolution

This allows you to activate or deactivate the Advanced AccuBlend

feature.

Presentation .. Recommended for making a presentation using a

PowerPoint file

Auto ............... Turns on the Advanced AccuBlend feature. The pro-

jector automatically reduces or enlarges the current

image to fit the full screen.

sRGB ............. Standard color values

Native............. Turns off the Advanced AccuBlend feature. The pro-

jector displays the current image in its true resolu-

tion.

Graphic .......... Recommended for graphics

Video ............. Recommended for regular picture such as TV pro-

gram

See "Auto Adjust" on page E-45 for turning on or off

the Auto Adjust feature.

Movie ............. Recommended for movie

User 1-4 ......... User adjustable

NOTE:

* When "Resolution" is set to "Native", "3D Reform", "Aspect Ratio" , "Screen"

and "Overscan" are not available.

* While you are displaying an image with higher resolution than the projector's

native resolution “Native” is not available.

NOTE: When "sRGB", "Graphic", "Video" or "Movie" is selected, the brightness

decreases slightly when compared to "Presentation." This is not a malfunction.

User Adjust (when using User 1 to 4)

Selecting Overscan Percentage

Select overscan percentage (0%, 5%, 10% and 25%) for signal.

NOTE: When "Resolution" is set to "Native", this feature is not available, and

the stored settings and adjustments are invalid.

NOTE: When "4:3 Fill" or "Crop" is selected in "Aspect Ratio", this feature is not

available.

Selecting Video Filter Level (not available for Video, Viewer and LAN)

This function reduces video noise.

Off .................. The filter is removed.

Less ............... The low-pass filter is applied partially.

More .............. The low-pass filter is applied fully.

When selecting one of four user adjustable presettings (User 1 through

4), the submenu will be displayed.

You can customize each gamma or color. To do so, first select [Set-

ting] and press the ENTER button, and then proceed the following

steps.

E-39

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Gamma Correction Mode

Use the ̇ or ̈ buttons to choose one mode from three options.

Each mode is recommended for :

Projector Options

Using 3D Reform

This feature corrects trapezoidal distortion so that the projected im-

age is rectangular.

Dynamic ......... For true color reproduction of natural tones

Natural ........... Normal settings

Two options are available for correcting procedures.

You can save adjustment settings by using the 3D Reform Save op-

tion on Setup (See page E-45).

Black Detail .... For dark portions of a picture

Cornerstone

Selecting Color Correction

See page E-21

Adjusts red, green, blue, yellow, magenta, cyan and color gain each

independently to correct the tint on whole screen.

Adjusting Color Temperature and White Balance

This feature adjusts the color temperature using the slide bar.

Checking "Color Temperature" enables the color temperature slide

bar and disables the “White Balance” button.

Clear “Color Temperature” and press the White Balance button to

access the Contrast/Brightness adjustment for each R, G, and B.

NOTE: "Color Temperature" and "White Balance" are a trade-off.

The White Balance is not available for Viewer and LAN.

Keystone

Selecting Base Setting

This feature allows you to use color correction or gamma values as

reference data to optimize for various types of images.You can select

one of the following five settings.

• Presentation

• Video

• sRGB

• Movie

• Graphic

1. Press the SELECT ̇̈ button to adjust the horizontal keystone.

2. Press the SELECT ̆̄ button to select "Vertical".

3. Press the SELECT ̇̈ button to adjust the vertical keystone.

4. After completing, press the ENTER button.This will return to the menu

screen.

When "Resolution" is set to "Native", "Cornerstone" and "Keystone"

are not available.

E-40

Download from Www.Somanuals.com. All Manuals Search And Download.

Using Adapting Color Correction [Wall Color Correction]

2. Highlight "Automatic".

3. Use the SELECT ̄ button to highlight "Execute" and then press the

ENTER button.

The Auto Wall Color Correction will be executed.

This function allows for correcting the color of the projected images on

textured walls using the image sensor on the projector. There are two

ways for color correction: Automatic and Manual. Automatic correction

affects all colors; Manual correction allows you to correct each color R,

G, B, and W respectively.

NOTE: When Auto Wall Color Correction is enabled in the Auto Functions menu,

Wall Color Correction can be executed by pressing and holding the AUTO AD-

JUST or AUTO ADJ button for a minimum of 2 seconds.

Manual Wall Color Correction

Off .................. Disables this function

Preparation: Before correcting manually, prepare a non-glossy, non-

transparent, clean white paper (300 mm x 420 mm). Hereafter re-

ferred to as "the white paper for Wall Color Correction."

User 1 to 4 ..... Executes correction.Four settings can be saved.User

4 (AutoAdjustButton) stores settings when the Auto

Function is executed by pressing and holding the

AUTO ADJUST button or AUTO ADJ. button for a

minimum of 2 seconds.

1. Choose a selection from User 1 – 4. Highlight "Setting" and press the

ENTER button.

The correction mode select screen is displayed.

To read the pre-adjustment settings. Choose a selection User 1 – 4,

highlight "OK" and press the ENTER button.

Info box .......... Displays "Automatic" or "Manual". This is the option

you have set for User 1 – 4 setting.

NOTE: Correction may not be possible depending on ambient room lighting,

walls with a texture that is glossy or with certain patterns, or walls that are the

2. Highlight "Manual".

color black or primary deep colors.

If you try to correct beyond the limit, an error message "Out of correction range!"

will be displayed. This message means that you will not be able to correct the

color due to the above reasons.

Also, When the image sensor fails to pick up the image of a wall color during

Auto Wall Color Correction, an error message "Failed to execute Auto Wall Color

Correction" will be displayed. This message means that there may be an obstacle

between the wall and the image sensor on the projector, or the image sensor

may not work because of too much ambient light. Make corrections to what

seems to be the problem and try again.

3. Use the SELECT ̄ button to highlight "Execute" and then press the

ENTER button.

The Manual Wall Color Correction (Red) screen will be displayed.

Automatic Wall Color Correction

1. Choose a selection from User 1 – 4. Highlight "Setting" and press the

ENTER button.

The correction mode select screen will be displayed.

To read the pre-adjustment settings. Choose a selection from User 1

– 4, highlight "OK" and press the ENTER button.

Working area

E-41

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Place the white paper forWall Color Correction over the working area

in the Manual Wall Color Correction (Red) screen.

Paste the white paper for Wall Color Correction loosely or get some-

one to hold it.

6. Use the SELECT ̆̄̇̈ button to move the yellow box to select a

color density.

Moving the yellow box changes the color density of the selected por-

tion in the palette.

Move the yellow box so that a color on the white paper for Wall Color

Correction becomes close to a color of the projected image on the

wall.

Position of the white paper for

Wall Color Correction

NOTE: The size of the above Manual Wall Color Correction screen changes de-

pending on the screen size.

Actual color of the projected

image on the wall

5. Use the SELECT ̇ or ̈ button to move the blue frame to the work-

ing area and then press the ENTER button.

A yellow box will appear in the palette.

Color of the projected image on the white

paper for Wall Color Correction

To move the Manual Wall Color Correction (Red) screen, high-

light "Move" and then press the ENTER button.

7. When you complete the correction, press the ENTER button.

The "Next" will be highlighted.

The "Slide Bar" button adjusts Hue, Saturation and Brightness.

8. Press the ENTER button.

The Manual Wall Color Correction (Green) screen will be displayed.

Palette

Yellow box

9. Repeat steps 4 to 8. Adjust Red, Green, Blue and White respectively.

When you complete correcting White, the Exit Adjustment screen is

displayed.

10. Highlight the Correction Level bar and then use the SELECT ̇ or ̈

button to finely adjust.

Blue frame

11. Highlight "OK" and press the ENTER button.

E-42

Download from Www.Somanuals.com. All Manuals Search And Download.

Allows you to set preferences for the on-screen menu. Press "OK" to

save your changes for all the features of Page 1 and Page 2.

[Page 2]

[Page1]

Turning On / Off Source Display [Source Display]:

This option turns on or off input name display such as RGB1/2,Video,

and No Input to be displayed in the top right corner of the screen.

Selecting Menu Language [Language]:

Turning On / Off Message [Message]:

This option turns on and off messages for lamp life warning, 3-minute

before power off time and "This feature is not available."

You can choose one of seven languages for on-screen instructions.

The options are:English, German, French, Italian, Spanish, Swedish

and Japanese.

Selecting Menu Color [Menu Color Select]:

You can choose between two color modes for menu color: color and

monochrome.

Selecting Menu Mode [Menu Mode]:

This feature allows you to select 3 menu modes: Advanced Menu,

Custom Menu and Basic Menu.

Advanced Menu ............ This is the menu that contains all the avail-

able menus and commands.

Basic Menu ................... This is the basic menu that contains mini-

mum essentials of menus and commands.

Custom Menu ............... This is the menu that you can customize us-

ing the Custom Menu Edit to fit your needs.

Customizing the Menu:

See page E-32 for instructions about how to customize the Menu.

Selecting Projecting Pointer Icon [Projector Pointer]:

This enables you to select from eight different Pointer icons for the

"Pointer" button on your remote control.

After moving your Pointer icon to the area you want on the screen,

press the Magnify button on the remote control to enlarge the se-

lected area on the screen. See page E-25 for more details.

NOTE: There may be cases where the Pointer function is not available (ex. a

non-interlace signal at 15kHz such as video game.)

Selecting Menu Display Time:

This option allows you to select how long the projector waits after the

last touch of a button to turn off the menu.

The preset choices are "Manual", "Auto 5 sec", "Auto 15 sec", and

"Auto 45 sec". The "Auto 45 sec" is the factory preset.

Manual ........... The menu can be turned off manually.

Auto 5 sec ...... The menu will automatically be turned off in 5 sec-

onds if no buttons are pressed within 5 seconds.

Auto 15 sec .... The menu will automatically be turned off in 15 sec-

onds if no buttons are pressed within 15 seconds.

Auto 45 sec .... The menu will automatically be turned off in 45 sec-

onds if no buttons are pressed within 45 seconds.

E-43

Download from Www.Somanuals.com. All Manuals Search And Download.

Setup

Enables you to set operating options.

[Page 2]

Press "OK" to save your changes for all the features of Page1, Page2,

Page3, Page 4, Page 5 and Page 6.

[Page 1]

Setting Viewer Options [Viewer Options]

Show Folder List:

If this option is checked, when the Viewer source is selected on the

projector, the folder lists will be displayed and allows you to select the

presentation from a PC card.

Selecting Projector Orientation [Orientation]:

This reorients your image for your type of projection.The options are:

desktop front projection, ceiling rear projection, desktop rear projec-

tion, and ceiling front projection.

Auto Play:

If this option is checked, when the Viewer source is selected on the

projector any given slide will start to play automatically.

Selecting a Color or Logo for Background [Background]:

Use this feature to display a blue/ black screen or logo when no sig-

nal is available.The default background is “Blue”.You can change the

logo screen using the PC Card Files feature. See pages E-27 and

52.

Auto Play Interval:

You can specify interval time between 5 and 300 seconds.

NOTE: The Auto Play Interval time set on “Slide Show Settings” of the Dy-

namic Image Utility 2.0 overrides the one set here.

Setting RGB 1 or 2 for RGB OUT [RGBOUT Terminal]:

This option allows you to determine which RGB source is output from

the RGBOUT connector during Idle mode.

Manual Play:

Views a slide manually when the Viewer source is selected.

Selecting Capture Options [Capture Option]: (available for JPEG only)

These options are used for the Capture function that you can select

from Tools. You have three options for JPEG compression quality:

High quality, Normal and High Compression.

Last ................ The signal from the last RGB input will be output to

the RGBOUT connector.

RGB 1 ............ The signal from RGB1 IN will be output to the

RGBOUT connector.

High Quality .................. Gives quality of JPEG a priority.

Normal .......................... Gives normal JPEG quality.

High Compression ........ Gives compression a priority.

RGB 2 ............ The signal from RGB2 IN will be output to the

RGBOUT connector.

NOTE: The AUDIO OUT mini jack will not output sound during the Idle mode.

Setting Mouse Button and Sensitivity [Mouse]:

This option lets you to change your USB mouse settings.The mouse

settings feature is available for USB mouse only. Choose the settings

you want:

Setting Closed Caption:

This option sets several closed caption modes that allows text to be

superimposed on the projected image.

CAPTION 1-4 Text is superimposed.

Mouse Button ............... "Right Hand" or "Left Hand"

Mouse Sensitivity .......... "Fast", "Medium" or "Slow"

TEXT 1-4 ....... Text is displayed in full screen.

OFF ............... This exits the closed caption mode.

Selecting Operation Mode [Operation Mode Select]

Set the operation mode of the USB mouse connected to the USB

port (MOUSE/HUB) on the projector

Auto ............... Depending on connection of the USB port (PC) on

the projector and a USB port (type A) on your PC,

the USB mouse is operated in the following way:

When connecting the projector to your PC

The USB mouse connected to the projector can

be used as a PC mouse.

When not connecting the projector to your PC

The USB mouse connected to the projector can

perform menu operation of the projector.

Projector ........ The USB mouse connected to the projector can per-

form menu operation of the projector.

E-44

Download from Www.Somanuals.com. All Manuals Search And Download.

[Page 3]

Enabling Auto Start [Auto Start]:

Turns the projector on automatically when the power cable is inserted

into an active power outlet and the main power switch is turned on.

This eliminates the need to always use the "Power" button on the

remote control or projector cabinet.

Enabling Power Management [Power Management]:

When this option is on and there is no input for five minutes or more,

the projector will automatically turn itself off.

Enabling Power Off Confirmation [Power Off Confirmation]:

This option determines whether a confirmation dialog for turning off

the projector will appear or not.

NOTE: When the confirmation message is displayed, you must be in the Pro-

jector mode to operate your projector using the remote control. If not, press

the PJ button on the remote control to change your projector to the Projector

mode. The button lights to indicate that you are in the Projector mode.

Enabling Horizontal and Vertical Keystone Correction Save

[3D Reform Save]:

This option enables you to save your current 3D Reform settings.

Saving your change once affects all sources.The changes are saved

when you turn off the projector.

Selecting Signal Format [Signal Select]

RGB1/2:

Allows you to choose "RGB" for an RGB source such as a computer,

or "Component" for a component video source such as a DVD player.

Normally select "RGB/Component" and the projector automatically

detects an either incoming signal. However there may be some com-

ponent signals that the projector is unable to detect. If this is the

case, select "Component". Select "Scart" in RGB 1 or 2 for the Euro-

pean Scart.

Enabling High Speed Fan Mode [High Speed Fan Mode]:

This option allows you to select two modes for fan speed:high-speed

mode and normal speed mode.

When you wish to cool down the temperature inside the projector

quickly, check this box.

NOTE: Enable High Speed Fan mode if you continue to use the projector for

consecutive days.

VIDEO and S-VIDEO:

This feature enables you to select composite video standards manu-

ally. Normally select "Auto". Select the video standard from the pull-

down menu. This must be done for Video and S-Video separately.

Selecting Built-in Speakers[Built-in Speaker]:

This option allows you to mute the built-in speakers.

[Page 4]

Enabling Idle Mode [Idle Mode]:

The projector has two standby modes: Standby and Idle.

Standby is the mode that allows you to put the projector in the standby

condition which consumes less power than the idle mode. The pro-

jector is preset for Standby at the factory.

When this check box is turned on, you allow the RGB OUT connector

to output RGB signal during Idle mode.

NOTE:

* The RGB OUT connector will not output signal during the Standby mode.

* Via the USB interface the projector can be turned on from your PC using

Dynamic Image Utility 2.0 during the Standby or Idle mode. On the LAN

connection the projector can be controlled or monitored from your PC us-

ing Dynamic Image Utility 2.0 only in the Idle mode.

* The HTTP server functions are not available during Standby mode.

Resetting the Filter Usage Hours [Clear Filter Usage Meter]:

Resets the filter usage back to zero. Pressing this button appears a

confirmation dialog box. To reset the filter usage hours, press "OK".

Enabling Auto Adjust [Auto Adjust]:

When "Auto Adjust" is set to "On", the projector automatically deter-

mines the best resolution for the current RGB input signal to project

an image using NEC's Advanced AccuBlend Intelligent Pixel Blend-

ing Technology.

The image can be automatically adjusted for position and stability;

"Horizontal Position", "Vertical Position", "Clock", "Phase", and "Reso-

lution".

On .................. Automatically adjusts image "Horizontal Position",

"Vertical Position", "Clock", "Phase" and "Resolution".

Off .................. User can adjust the image display functions ("Hori-

zontal Position", "Vertical Position", "Clock", "Phase"

and "Resolution") manually.

E-45

Download from Www.Somanuals.com. All Manuals Search And Download.

[Page 5]

[Page 6]

Remote Sensor:

Selecting Communication Speed [Communication Speed]:

This feature sets the baud rate of the PC Control port (Mini DIN 8

Pin). It supports data rates from 4800 to 38400 bps.

This option determines which remote sensors on the projector are

enabled in wireless mode.

The options are: front, rear, right, or left. All checked boxes indicate

that they can accept the infrared signal from the supplied remote

control.

The default is 38400 bps. Select the appropriate baud rate for your

equipment to be connected (depending on the equipment, a lower

baud rate may be recommended for long cable runs).

S-Video Mode Select:

Selecting Default Source [Default Source Select]:

You can set the projector to default to any one of its inputs each time

the projector is turned on.

This feature is used to select the S-Video signal detection mode.

This allows identifying of the S-Video signals with different aspect

ratio (16:9 and 4:3).

Last ................ Sets the projector to default to the previous or last

active input each time the projector is turned on.

Off .................. Does not identify any S-video signal.

S2 .................. Identifies the 16:9 or 4:3 signal.

Auto ............... Searches for an active source in order of RGB1 →

RGB2 →Video → S-Video → DVI(DIGITAL) →Viewer

→ RGB1 and displays the first found source.

Select ............. Displays the selected source input every time the pro-

jector is started up.Select an input from the pull-down

menu.

Disabling the Cabinet Buttons [Control Panel Key Lock]:

This option turns on or off the Control Panel Key Lock function.

NOTE:

* This Control Panel Key Lock does not affect the remote control and the PC

Control functions.

* When the cabinet buttons are disabled, pressing and holding the CANCEL

button for about 10 seconds will change the setting to enabled.

Selecting Lamp Mode and Lamp Type [Lamp Setting]

Lamp Mode:

This feature enables you to select two brightness modes of the lamp:

Normal and Eco modes. The lamp life can be extended by using the

Eco mode.

Normal Mode . This is the default setting (100% Brightness).

Eco Mode ...... Select this mode to increase the lamp life (80% Bright-

ness).

Lamp Type:

The lamp type you use is displayed here.

MT60LP ......... Standard life lamp

MT60LPS ....... Optional extended life lamp. When the optional ex-

tended life lamp is used, the Lamp Mode is available.

E-46

Download from Www.Somanuals.com. All Manuals Search And Download.

Selecting Aspect Ratio and Position for Screen [Screen]

Screen Type:

Select either 4:3 Screen or 16:9 Screen for the screen to be used.

See also "Aspect Ratio" on page E-38.

NOTE: When "Resolution" is set to "Native", this selection is inactive.

Position:

This feature adjusts the vertical position of the image when viewing

video with an aspect ratio selected.

When some aspect ratios are selected in Image Options, the image

is displayed with black borders on the top and bottom.

You can adjust the vertical position between top and bottom.

NOTE: This option is not available when "4:3" is selected in Screen Type and

"Letterbox" is selected in Aspect Ratio.

NOTE: During 3D Reform adjustment, "Screen Type" and "Screen Position"

may not be available. To make available, first reset the 3D Reform data and

then do settings again. Secondly repeat the 3D Reform adjustment. Changing

"Screen Type" and "Screen Position" can limit 3D Reform in its adjustable

range.

Selecting Auto Functions

Focus:

When Auto Focus is enabled in the Auto Functions menu, Auto Fo-

cus can be executed by pressing and holding the AUTO ADJUST or

AUTO ADJ button for a minimum of 2 seconds.

Wall Color Correction:

When Wall Color Correction is enabled in the Auto Functions menu,

Wall Color Correction can be executed by pressing and holding the

AUTO ADJUST or AUTO ADJ button for a minimum of 2 seconds.

Correction settings will be saved on "User 4 (AutoAdjustButton)".

NOTE:

1. If neither Focus or Wall Color Correction are enabled in the Auto Functions

menu when you press and hold the AUTO ADJUST or AUTO ADJ button

for a minimum of 2 seconds, the Auto Adjust function (Position/Clock/

Phase) will be performed instead of Auto Focus and Auto Wall Color Cor-

rection.

2. Due to specifications of the image sensor on the projector, Auto Functions

are effective to image sizes between 40" and 150"(diagonal). Also in some

cases Auto Functions may not work correctly depending on projection

conditions such as textured material of the screen or ambient light.

E-47

Download from Www.Somanuals.com. All Manuals Search And Download.

DNS Configuration

Setting LAN Mode

....................... Type in the IP address of DNS server on the network

connected to the projector.12 numeric characters are

used.

This feature allows you to set various setting items when the projector is

used on your network.

Consult with your network administrator about these settings.

Domain Name Type in domain name of the network connected to

the projector. Up to 60 alphanumeric characters can

be used.

NOTE:

•

A LAN card is required for LAN connection; NEC's optional wireless LAN card

is available. For more information on inserting or ejecting a LAN card, see

pages E-28.

Either PC Card Slots 1 or 2 can accept LAN card. If two LAN cards are in-

serted into both PC card slots, the first inserted one is effective.

NetworkType (required for wireless only)

CAUTION:Make sure that the LAN card is removed during Standby

mode (NOT Idle mode) or with the main power off.

Failure to do so may cause damage to the data on your PC card.

Mode:

Select communication method when using wireless LAN.

Infrastructure ................ Select this option when communicating with

one or more equipment connected to the

wireless or wired LAN network via an ac-

cess point.

IP Address

802.11 Ad Hoc .............. Select this option when using the wireless

LAN to communicate with a computer in a

one-to-one correspondence. This is a

method that meets the IEEE802.11 wireless

standard.

An IP address can be automatically assigned to this projector by your

DHCP server. If your network does not automatically assign IP address,

ask your network administrator for an address, and then register it manu-

ally.

Ad Hoc .......................... Select this option when using the wireless

LAN to communicate with a computer in a

one-to-one correspondence.

Automatic ....... Automatically assigns an IP address to the projector

from a DHCP server.

Manual ........... Provides a space for you to register the IP address or

subnet mask number obtained from your network ad-

ministrator.

Easy Connection .......... This allows you to easily set up wireless LAN

connection. See the supplied Software Util-

ity Installation Guide for more information.

IP Address ..... Set your IP address. Press to display the software

keyboard and type in 12 numeric characters.

SSID (Network name):

Enter an identifier (SSID) for wireless LAN. Communication can be

done only with equipment whose SSID matches SSID for your wire-

less LAN. Up to 16 alphanumeric characters can be used (Case-

sensitive).

Subnet Mask .. Set your subnet mask number. Press

to display

the software keyboard and type in 12 numeric char-

acters.

Projector Name

NOTE: To disable SSID, select a space (null) or "ANY"(All caps).

....................... Specify a unique projector name. Press

to display

the software keyboard and type in.Up to 16 alphanu-

meric characters can be used.

Channel:

Set this option when selecting [802.11 Ad Hoc] or [Ad Hoc] in [Mode].

Select a channel number from the pull-down list. The channel must

match for all wireless devices communicating on your wireless LAN.

Gateway ......... Set the default gateway of the network connected to

the projector. Press

to display the software key-

board and type in 12 numeric characters.

Checking this box will make the set default route valid.

When data is sent from the LAN card, the transfer

location will be searched according to the previously

set routing information; however, when the transfer

location has not been found as a result of the search,

the data will be sent to the device that holds the IP

address set here.The IP address that is set here must

be one that can be identified by a search of the rout-

ing information.

NOTE: Channels in the pull-down list are different depending on which coun-

try you live in.

TX rate:

Select a wireless transmission speed.Normally leave it as Automatic.

Try another transmission speed when the connection fails.

E-48

Download from Www.Somanuals.com. All Manuals Search And Download.

WEP (for Wireless only)

Mail

Select this option whether using the WEP (Wired Equivalent Privacy)

key for encryption or not. To use encryption, specify WEP key.

NOTE: To the Mail Alert feature on wireless LAN connection, select "Infrastruc-

ture" for "Mode" in "Network Type." "Test Mail" is available only when there is a

LAN card in the PC card slot of the projector.

Disable ........... Will not turn on the encryption feature.Your commu-

nications may be monitored by someone.

Alert Mail:

Checking this box enables Alert Mail feature.

This option notifies your computer of an error message via e-mail

when using wireless or wired LAN.The error message will be notified

when the projector lamp has reached the end of its usable life or an

error occurs in the projector.

64bit ............... Uses 64-bit datalength for secure transmission.

128bit ............. Uses 128-bit datalength for secure transmission.This

option will increase privacy and security when com-

pared to use of 64bit datalength encryption.

Sample of a message sent from the projector:

The lamp is at the end of its usable life. Please replace the lamp.

NOTE: The WEP settings must be the same as communication devices such as

PC or access point in your wireless network. When you use WEP, your image

transmission speed will slow down.

Projector Name: X X X X

Lamp Hour Meter: xxxx [H]

Projector Usage: xxxxxx [H]

Key Select:

Selects one key from the four keys below when selecing [64bit] or

[128bit] in [WEP].

Sender's Address:

Key1-4:

Specify the senders address. Use the Software keyboard. Up to 60

alphanumeric and symbols characters can be used.See "Using Soft-

ware Keyboard" in Appendix for more details.

Enter encryption key when selecting [64bit] or [128bit] in [WEP].

The key can also be set in hexadecimal digit.

Enter 0X(numeral and alphabet respectively) right in front of your

key code.

SMTP Server Name:

Type in the SMTP server name to be connected to the projector. Up

to 60 alphanumeric characters can be used.

Hexadecimal uses 0 to 9 and A to F.

Up to 10 characters can be set in 64 bit and up to 26 characters

in 128 bit.

Recipient's Address 1 to 3:

Type in your recipient's address. Up to 60 alphanumeric and symbols

characters can be used.

Test Mail:

Send a test mail to check if your settings are correct.

NOTE: If you entered an incorrect address in a test, you may not receive an

Alert mail. Should this happen, check if the Recipient's Address is correctly

set.

NOTE: Unless any one of the "Sender's Address", "SMTP Server's Name" or

"Recipient's Address 1-3" is selected, "Test Mail" is not available.

NOTE: Be sure to highlight “OK” and press the ENTER button before execut-

ing “Test Mail”.

E-49

Download from Www.Somanuals.com. All Manuals Search And Download.

Status

Make sure that "̄" is highlighted and then press the ENTER button.

The Software keyboard appears. Use the Software keyboard to type

a password and then highlight "OK" on the “Enter the Password”

screen and press the ENTER button.

The [Confirm Password] screen will be displayed.

2. Type the same password again.Highlight "OK" on the“Enter the Pass-

word” screen and press the ENTER button.

Your password will be assigned.

Delete

To delete your password:

1. Highlight [Delete] and press the ENTER button. The "Current Pass-

word" screen will be displayed.

Displays the status of the LAN settings.

IP Address ..... Indicates the IP address of the projector.

Subnet Mask .. Indicates the subnet mask of the projector.

MAC Address. Indicates the MAC address of the LAN card.

2. Use the Software keyboard to type your password. Highlight "OK" on

the “Current Password” screen and then press the ENTER button.

Your password will be deleted.

Setting a Password

A password can be set for your projector to avoid operation by an unau-

thorized person.

In case you forget your password, follow the steps below to delete it.

1. Select the Advanced menu from the Basic menu. The "Password"

entry screen will be displayed.

There are two password options: one for menu and the other for logo.

When a password is set, doing any one of the following four operations

will display the Password input screen.

2. Use the Software keyboard to type "1111".

Highlight "OK" on the “Password” entry screen and then press the

ENTER button.

For Menu:

Changing the menu to Advanced

The "Password Warning!!" message will be displayed.

Editing the custom menu

3. Use the Software keyboard to type "3333".

Highlight "OK" on the “Password” entry screen and then press the

ENTER button.

For Logo:

Changing the background

Changing the logo data in PC Card Files

The "Password Warning!!" message will be displayed.

4. Use the Software keyboard to type "5555".

Highlight "OK" on the “Password” entry screen and then press the

ENTER button.

The "Delete Password. Are you sure? Yes/No" dialog box will be dis-

played.

Procedures for Password setting apply to both Menu and Logo.

Entry

To assign your password:

NOTE: Up to 15 alphanumeric characters can be assigned.

5. Use the SELECT ̇ or ̈ button to highlight "Yes" and press the EN-

TER button.

1. Type a password.

Highlight "Entry" and press the ENTER button.

Your password will be deleted.

The "Enter the Password screen" will be displayed.

E-50

Download from Www.Somanuals.com. All Manuals Search And Download.

4. Use the SELECT ̆̄ button to select "Keyword" and use the soft-

Security

ware keyboard to enter a keyword.

The Security function enables you to protect your projector so that the

projector will not project a signal unless you enter a keyword. There is

also an option to lock the projector by using a registered PC card as a

protect key. Once you have registered your PC card as a protect key,

you are required to insert the registered PC card into the PC card slot of

the projector each time you turn on the projector. You can enable the

Security function by using a keyword only.

NOTE: To use a PC card as a protect key, you must also set up a keyword.

Please make a note of your keyword.

This completes registration of your PC card.

To enable Security, use the SELECT ̆̄ button to select "Enable" and

use the SELECT ̆̄ button to select "OK" and "Security function will

be enabled. An “Are you sure?" message will appear. Use the SELECT

̇̈ button and press the ENTER button.

The Security function takes effect.

To turn on the projector when Security is enabled (when using your

keyword only).

1. Press and hold the POWER button for a minimum of two seconds.

The projector will be turned on and display a message to the effect

that the projector is security-protected.

2. Select [Projector Options] → [Security] from the menu and press the

ENTER button.

The Release Code input screen will be displayed.

3. Enter your keyword in the Release Code input screen.

You can view the projected image.

Enable/Disable.............. This turns the Security function on or off.

NOTE: Do not forget your keyword. However, if you forget your keyword, NEC

or your dealer will provide you with your Release Code. See more information

at the end of this section.

Keyword ........................ Enter an appropriate keyword when you use

the Security function.

(Up to 10 characters can be used.)

To turn on the projector when Security is enabled (when using a

PC card as a protect key).

The Security function is available only when

your keyword is entered.

Use Protect key ............ Check this box to lock your projector when

using a PC card. To use a keyword without

1. Insert your registered PC card into the PC card slot.

2. Press and hold the POWER button for a minimum of two seconds.

The projector will turn on and then recognize the PC card. Once the

image has been projected, it will stay on without the PC card.

a PC card, do not check this box.

Drive ............................. Switches between PC Card slot 1 and 2.

Read ............................. Reads data of a PC card.

•

The security disable mode is maintained until the main power is turned

off (by setting the main power switch to "O" or unplugging the power

cord).

The Security function is not available unless

at least one PC card is registered. (if the

“Use Protect key” check box is selected)

In the following cases you will be asked to check the protect key or

input the keyword:

Up to 5 PC cards can be registered.

(1) When "OK" is selected at an image for which security is set and

the power is turned off then back on

Delete ........................... Deletes data of a registered PC card.

(2) When the main power is turned off then back on while the secu-

rity function is enabled

To set up a keyword to enable the Security function without using

a registered PC card.

(3) When you attempt to display an image for which security is set

while the security function is enabled

1. Use the SELECT ̆̄ button to select “Keyword” and use the soft-

ware keyboard to enter a keyword.

•

Blanks (spaces) cannot be used in the Keyword section.

To delete PC card data you registered.

NOTE: Please make a note of your keyword.

2. Use the SELECT ̆̄ button to select “Enable” and use the SELECT

̆̄ button to select “OK”, then the Security function will be enabled.

An “Are you sure?” message will appear. Use the SELECT ̇̈ but-

ton and press the ENTER button.

1. Use the SELECT ̆̄ button to select "Delete" and use the SELECT

̇ button to select the list window.

2. Use the SELECT ̆̄ button to select the PC card data you wish to

delete.

The Security function takes effect.

3. Press the SELECT ̈ button to select "Delete" and press the ENTER

button.

To register a PC card as a protect key.

The PC card data will be deleted.

1. Insert a PC card into the PC card slot of the projector.

2. Use the SELECT ̆̄ button to select "Read" and press the ENTER

button.

Data of the PC card will be read into the projector.

3. Use the SELECT ̆̄ button to select "Register" and press the EN-

TER button.

Downloaded data will be registered and be displayed in the list win-

dow.

E-51

Download from Www.Somanuals.com. All Manuals Search And Download.

If you've lost your registered PC card, proceed as follows:

Using ChalkBoard

The ChalkBoard feature allows you to write and draw messages on a

projected image. See page E-27

NOTE: NEC or your dealer will provide you with your Release Code in exchange

for your registered keyword and Request Code. See more information at the end

of this section.

NOTE: This feature is available only when using with USB mouse. See page E-

26.

1. Press and hold the POWER button for a minimum of two seconds.

Help

The projector will be turned on and display a message to the effect

that the projector is security-protected.

Contents

Provides an online help about how to use the menus.An underlined link

means that you can move to an adjustment item directly.

Selecting the underlined link and pressing ENTER moves to the corre-

sponding adjustment item.

2. Select [Projector Options] → [Security] from the menu and press hte

ENTER button.

The Release Code input screen will be displayed as well as your

Request Code (24 alphanumeric characters).

3. Enter your Release Code in the Release Code Input screen.

Information

Displays the status of the current signal, and the lamp and the projector

usage hours. This dialog box has three pages.

The information included are as follows:

If the projector is turned on by entering the Release Code, your Se-

curity will be disabled.

[Page 1]

[Page 2]

[Page 3]

NOTE:

Source Name

Input Terminal

Entry No.

Horizontal Frequency

Vertical Frequency

Sync Polarity

Signal Type

Video Type

Sync Type

Interlace

Remaining Lamp Time (%)

Lamp Hour Meter (H)

Filter Usage (H)

* Some types of PC cards cannot be registered as your protect key.

* It is recommended that you register two or more PC cards in case you lose or

damage your registered PC card.

Projector Usage (H)

* Formatting your registered PC card will disable your protect key function.

NOTE:

For additional information visit:

US : http://www.necvisualsystems.com

Europe : http://www.nec-europe.com/

Global : http://www.nec-pj.com/

NOTE: The progress indicator shows the percentage of remaining bulb life. The

value informs you of the amount of lamp and projector usage respectively.

Remaining Lamp Time Display

When the remaining lamp time reaches 0, the Remaining Lamp Time

bar indicator changes from 0% to 100 Hours and starts counting down.

If the remaining lamp time reaches 0 hours, the projector will not turn on

regardless of whether the lamp mode is set to Normal or Eco.

Tools

Provides tools for setting sleep timer, capturing images, displaying files

or changing your background logo in a PC Card and drawing.

NOTE: The "Capture" and "PC Card Files" features are required for a PC card.

Returning to Factory Default

The Factory Default feature allows you to change adjustments and set-

ting to the factory preset for source except the following:

Using Sleep Timer

1. Select your desired time between 30 minutes and 16 hours:Off, 0:30,

1:00, 2:00, 4:00, 8:00, 12:00, 16:00.

All Data ......................... Reset all the adjustments and settings for

all the signals to the factory preset except

Remaining Lamp Time, Lamp Hour Meter,

Filter Usage, Projector Usage, Language,

Background, Communication Speed, LAN

Mode, Security and Password.

2. Select “Set” and press the ENTER button on the remote control.

3. The remaining time starts counting down.

4. The projector will turn off after the countdown is complete.

Including Entry List:

NOTE:

Also deletes all the signals in the Entry List

and returns to the factory preset.

• To cancel the preset time, set "Off" for the preset time or turn off the power.

• When the remaining time reaches 3 minutes before the projector is turned off,

the "Projector will turn off in 3 minutes" message will be displayed on the

bottom of the screen.

Current Signal ............... Resets the adjustments for the current sig-

nal to the factory preset levels.

All the items in "Picture", "Sound", "Image

Options" and "Picture Management" can be

reset.

Using Capture

Allows you to capture an image from a source that is currently being

displayed. The image is saved as JPEG in the PC card. When you se-

lect Capture from the menu, you will get a tool bar.You can capture an

image directly using the tool bar when the menu is not displayed.

See page E-30.

Using PC Card Files

The PC Card Files feature allows you to display a list of all the files

stored in the PC card so that you can select a file you want to display.

You can also sort files by file name or date, or display the file. See page

E-31.

Changing Background Logo:

You can change the default background logo using the PC Card Files

feature.

NOTE: File size must be 256KB or less. Other file formats than JPEG and BMP

are not available. See page E-27.

E-52

Download from Www.Somanuals.com. All Manuals Search And Download.

MAINTENANCE

This section describes the simple maintenance procedures you should

follow to replace the lamp and the filter, and to clean the filter, the cabi-

net and the lens.

4. Insert a new lamp housing until the lamp housing is plugged into the

socket.

Replacing the Lamp

After your lamp has been operating for 2000 hours (Normal mode on

the standard life lamp) or longer, the "Lamp" indicator in the cabinet will

blink red and the message will appear. Even though the lamp may still

be working, replace it as soon as possible to maintain optimal projector

performance.

CAUTION

•

DO NOT TOUCH THE LAMP immediately after it has been used.

It will be extremely hot. Turn the projector off, wait 90 seconds,

turn off the main power switch, and then disconnect the power

cable. Allow at least one hour for the lamp to cool before han-

dling.

CAUTION:Do not use a lamp other than the NEC replacement lamp

(Standard life lamp: MT60LP or Extended life lamp: MT60LPS).

5. Secure it in place with the two screws.

Be sure to tighten the screws.

•

DO NOT REMOVE ANY SCREWS except the two lamp case

screws.You could receive an electric shock.

The projector will turn off and go into stand by mode after 2100

hours (Normal mode on the standard life lamp) of service. If this

happens, be sure to replace the lamp. If you continue to use the

lamp after 2000 hours (Normal mode on the standard life lamp)

of use, the lamp bulb may shatter, and pieces of glass may be

scattered in the lamp housing. Do not touch them as the pieces

of glass may cause injury.

If this happens, contact your NEC dealer for lamp replacement.

To replace the lamp:

6. Reattach the lamp cover.

NOTE:The optional lamp comes with a flat-head screwdriver.

1. Remove the lamp cover by pushing two grooves lightly with the flat-

head screwdriver.

7. Snap the lamp cover into place.

2. Loosen the two screws securing the lamp housing until the screw-

driver goes into a freewheeling condition. The two screws are not

removable.

NOTE: Replacing a new lamp automatically clears the lamp usage hours.

NOTE: The lamp housing has an EEPROM chip memorizing its amount of usage

hours. You can check the amount usage hours in Information of the menu. (The

standard lamp and the optional lamp have an EEPROM chip in it so that when

you remove it, your lamp usage hours are saved in its own memory. The projec-

tor reads the lamp usage hours from the EEPROM chip to display them in Infor-

mation of the menu.)

3. Remove the lamp housing by pulling out the handle.

NOTE: There is an interlock on this case to prevent the risk of electrical shock.

Do not attempt to circumvent this interlock.

Interlock

E-53

Download from Www.Somanuals.com. All Manuals Search And Download.

3. Reinstall the new filter cover.

Catch

Cleaning

Cleaning or Replacing the Filter

The air-filter sponge keeps the inside of the projector from dust or dirt

and should be cleaned after every 100 hours of operation (more often in

dusty conditions).If the filter is dirty or clogged, your projector may over-

heat.

CAUTION

•

Turn off the power and unplug the projector before replacing

the filter.

•

Only clean the outside of the filter cover with a vacuum cleaner.

Do not attempt to operate the projector without the filter cover.

NOTE: Do not wash the filter with soap and water. Soap and water will damage

the filter membrane. Before replacing the filter, remove dust and dirt from the

projector cabinet. Keep out dust and during filter replacement.

To clean the air-filter:

Vacuum the filter-through the filter cover.

NOTE: When you replace the lamp, it is also wise to replace the filter. The filter

comes in the same package with your replacement lamp.

Cleaning the Cabinet and the Lens

To reset the filter usage time, from the menu, select [Projector Options]

→ [Setup] → [Page 4] → [Clear Filter Usage Meter] → [OK].

See also page E-45 for resetting the filter usage time.

To replace the filter (sponge):

1. Remove the filter cover by pushing up on the catch of the cover until

you feel it detach.

1. Turn off the projector before cleaning.

2. Clean the cabinet periodically with a damp cloth. If heavily soiled,

use a mild detergent. Never use strong detergents or solvents such

as alcohol or thinner.

3. Use a blower or lens paper to clean the lens, and be careful not to

scratch or mar the lens.

2. Gently peel off the filter (sponge) and replace it with the new one.

E-54

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLESHOOTING

This section helps you resolve problems you may encounter while setting up or using the projector.

Power Indicator

Indicator Condition

Off

Projector Condition

Note

The main power is off

–

Blinking light

Steady light

Green blinking

0.5 sec ON,

0.5 sec OFF

2.5 sec ON,

0.5 sec OFF

0.5 sec ON,

0.5 sec OFF

The projector is getting ready Wait for a moment.

to turn on.

Green blinking

Orange blinking

The projector is in Sleep mode.

–

The projector is cooling down. Wait for a moment.

Green

The projector is turned on.

The projector is in Standby or

Idle.

–

Orange

Status Indicator

Indicator Condition

Off

Red blinking

Projector Condition

Note

Normal

–

Blinking light

1 cycle (0.5 sec ON, Lamp cover error or lamp Replace the lamp cover or

2.5 sec OFF)

housing error

lamp housing correctly.

The projector is overheated.

Move the projector to a cooler

location.

2 cycle (0.5 sec ON, Temperature error

0.5 sec OFF)

3 cycle (0.5 sec ON, Power error

0.5 sec OFF)

Power unit will not work cor-

rectly.

4 cycle (0.5 sec ON, Fan error

0.5 sec OFF)

Fans will not work correctly.

6 cycle (0.5 sec ON, Lamp error

0.5 sec OFF)

Lamp fails to light. Wait a full

minute and then turn on again.

Contact your dealer.

7 cycles (0.5 sec ON,

0.5 sec OFF)

Fails to read lamp data

Re-firing the lamp

Control key locked

Green blinking

Orange

The projector is re-firing.

Steady light

You have pressed control

panel key when Control Key

Lock is enabled.

Green

Idle condition

–

Lamp Indicator

Indicator Condition

Projector Condition

Note

Off

Normal

–

Blinking light

Steady light

Red

Lamp has reached its end of Replace the lamp.

life. Lamp replacement mes-

sage will be displayed.

Red

Lamp has been used beyond Replace the lamp.

its limit. The projector will not

turn on until the lamp is re-

placed.

Green

Lamp mode is set to Eco mode

Extended life lamp is used

–

Orange

E-55

Download from Www.Somanuals.com. All Manuals Search And Download.

Common Problems & Solutions

Problem

Check These Items

Does not turn on

•

Check that the power cable is plugged in and that the power button on the projector cabinet or the remote

control is on. See pages E-17 and 18.

•

Ensure that the lamp cover or lamp housing is installed correctly. See page E-53.

Check to see if the projector has overheated or the lamp has reached the end of its usable life. If there is

insufficient ventilation around the projector or if the room where you’re presenting is particularly warm, move

the projector to a cooler location.

No picture

•

Use the menu to select your source (RGB 1/2, Video, S-Video, DVI, Viewer or LAN). See page E-19.

Ensure your cables are connected properly.

Use menus to adjust the brightness and contrast. See page E-38.

Remove the lens cap.

Reset the settings or adjustments to factory preset levels using the Factory Default in the Adjustment Menu.

See page E-52.

Image isn’t square to the

screen

•

Reposition the projector to improve its angle to the screen. See page E-19.

Use the 3DReform function to correct the trapezoid distortion. See page E-20.

Picture is blurred

•

Adjust the focus. See page E-20.

Reposition the projector to improve its angle to the screen. See page E-19.

Ensure that the distance between the projector and screen is within the adjustment range of the lens. See page

E-12 and 13.

•

Condensation may form on the lens if the projector is cold, brought into a warm place and is then turned on.

Should this happen, let the projector stand until there is no condensation on the lens.

Image is scrolling verti-

cally, horizontally or

both

Use menus or Source button on the remote control or the cabinet to select the source you want to input.

Remote control does

not work

•

Install new batteries. See page E-11.

Make sure there are no obstacles between you and the projector.

Stand within 22 feet (7 m) of the projector. See page E-11.

Make sure that you are in the Projector mode and the PJ button lights in red. If not, press the PJ button. See

page E-24.

Indicator is lit or blink-

ing

•

See the Status Indicator on pages E-55.

Cross color in RGB

mode

If Auto Adjust is off, turn it on or adjust the image manually with the Position/Clock in the Image Options. See

pages E-39 and 45.

USB mouse does not

work

Make sure that your USB mouse is properly connected to the projector.

The projector may not support some brands of a USB mouse.

When using the Viewer function

Problem

Check These Items

No picture

•

Is “Viewer” selected from the Source menu?

Is the PC card seated in the PC Crad slot completely?

Are slide data stored in the PC card?

Have the contents of the PC card been destroyed?

Part of a slide is not displayed

Contents of PC Card are damaged

•

While an image with over 1024

768 dots is projected, several lines of information will be lost. Use

the supplied software change the image to 1024

768 dots in size.

•

Use a computer, etc., to repair the data.

For more information contact your dealer.

E-56

Download from Www.Somanuals.com. All Manuals Search And Download.

SPECIFICATIONS

This section provides technical information about the MT1065/MT1060 Projector's performance

Model Number

MT1065/MT1060

Optical

LCD Panel

MT1065: 1.0" p-Si TFT active-matrix with Micro Lens Array

MT1060: 1.0" p-Si TFT active-matrix

Resolution

Lens

1024

768 pixels up to UXGA with Advanced AccuBlend

Motorized zoom and focus:

F1.74 – 2.18 f=30.8mm – 41.6mm

Lamp

275 W DC standard / 160 W DC (Optional Extended life lamp)

Color Image Sensor

Image Size

23,040 pixels (160 dots

144 lines)

25 inches – 500 inches (0.6 m – 12.7 m) diagonal

2.96 ft – 51.23 ft / 10.0 m (Tele) – 15.6 m (Wide)

Tele : 8.2° – 8.6° Wide : 9.8° – 10.5°

Projection Distance

Projection Angle

Electrical

Inputs

2 RGB (D-Sub 15 Pin/BNC

5), 1 DVI, 1 S-Video, 1 Video, 2 PC Card, 3 Stereo Mini Audio, 2 (L/R) RCA Audio,

1 PC Control, 1 (L/R) RCA Audio

Outputs

1 RGB, 1 Stereo Mini Audio

USB Port

1 A Type, 1 B Type

Video Compatibility

NTSC, NTSC4.43, PAL, PAL-60, PAL-N, PAL-M, SECAM, HDTV:1080p, 1080i, 720p, 576p, 576i, 480p, 480i

(w/optional cable)

Scan Rate

Horizontal: 15 kHz to 100 kHz (RGB: 24 kHz or over) / Vertical: 48 Hz to 120 Hz

RGB: 80 MHz (-3dB)

Video Bandwidth

Color Reproduction

Horizontal Resolution

16.7 million colors simultaneously, Full color

NTSC / NTSC4.43/PAL/PAL-M/PAL-N/PAL60: 550 TV lines

SECAM: 350 TV lines

YCbCr: 800 TV lines

RGB: 1024 dots (H)

768 dots (V),

External Control

Sync Compatibility

Built-in Speakers

Power Requirement

Input Current

RS232, IR, USB, LAN (optional)

Separate Sync / Composite Sync / Sync on G

2 (stereo)

100 - 120V AC / 200 - 240V AC, 50 / 60 Hz

4.0A (100 - 120V AC) / 2.0A (200 - 240V AC)

1.0W in Standby mode/390W in Lamp Normal mode/320W in Lamp Eco mode

(250W in use of the optional Extended Life lamp)

Power Consumption

Mechanical

Installation

Dimensions

Orientation: Desktop/Front, Desktop/Rear, Ceiling/Front, Ceiling/Rear

13.2" (W)

4.5" (H)

12.7" (D)

334mm (W)

115mm (H)

323mm (D)

(not including protrusions)

Net Weight

13.0 lbs / 5.9 kg

Environmental Considerations

Operational Temperatures

Storage Temperatures :

32° to 95°F (0° to 35°C), 20% to 80% humidity (non-condensing)

14° to 122°F (-10° to 50°C), 20% to 80% humidity (non-condensing)

UL Approved (UL 1950, CSA 950)

Regulations

Meets DOC Canada Class B requirements

Meets FCC Class B requirements

Meets AS/NZS3548 Class B

Meets EMC Directive (EN55022:1998, EN55024-1998, EN61000-3-2, EN61000-3-3)

Meets Low Voltage Directive (EN60950, TUV GS Approved)

For additional information visit:

US : http://www.necvisualsystems.com

Europe : http://www.nec-europe.com/

Global : http://www.nec-pj.com/

LCD panels are inherently susceptible to pixel defects.

For additional information regarding pixel data, please contact your local NEC sales office.

The specifications are subject to change without notice.

E-57

Download from Www.Somanuals.com. All Manuals Search And Download.

APPENDIX

Cabinet Dimensions

334(13.15")

Lens center

92.2(3.63")

Lens center

Unit = mm (inch)

16(0.63")

Pin Assignments of D-Sub RGB Input Connector

Mini D-Sub 15 Pin Connector

Pin No.

RGB Signal (Analog)

YCbCr Signal

Red

15 14 13 12 11

Green or Sync on Green

Blue

Signal Level

Ground

Video signal : 0.7Vp-p (Analog)

Sync signal : TTL level

* RGB 1 Input only

Ground

Red Ground

Cr Ground

Y Ground

Cb Ground

Green Ground

Blue Ground

No Connection

Sync Signal Ground

SCART Sync

Bi-directional DATA (SDA)*

Sync

Horizontal Sync or Composite Sync

Vertical Sync

Data Clock*

E-58

Download from Www.Somanuals.com. All Manuals Search And Download.

Compatible Input Signal List

Signal

Resolution

( Dots )

–

Frequency H.

( kHz )

15.734

Refresh Rate

( Hz )

NTSC

PAL

–

15.625

31.47

34.97

SECAM

VESA

–

640

480

640

480

640

480

640

480

640

480

640

480

640

480

640

480

640

480

720

350

720

400

720

350

720

400

800

600

800

600

800

600

800

600

800

600

832

624

1024

768

1024

768

1024

768

1024

768

1024

768

1024

768

1152

864

1152

870

1152

900

1152

900

1280

960

1280

1024

1280

1024

1280

1024

1280

1024

1280

1024

1280

1024

1400

1050

1920

1080

–

59.94

IBM

MAC

66.67

MAC

66.67

VESA

37.86

37.5

72.81

VESA

IBM

39.375

43.269

31.469

37.927

39.44

35.16

37.879

48.077

46.88

53.674

49.725

35.5

VESA

85.01

IBM

70.09

VESA

85.04

IBM

87.85

IBM

87.85

VESA

56.25

VESA

60.32

VESA

72.19

VESA

85.06

MAC

74.55

VESA

43 Interlaced

VESA

48.363

56.476

60.241

60.023

68.677

67.5

VESA

70.07

MAC

74.93

VESA

75.03

VESA

MAC

68.681

61.796

71.736

75.06

SUN

65.95

SGI

76.05

VESA

63.981

69.89

78.125

81.13

79.976

91.146

–

60.02

MAC

65.2

72.01

SUN

76.11

VESA

75.03

VESA

85.02

SXGA+

HDTV (1080p)

SDTV(576i)(625i)

SDTV(576p)(625p)

HDTV (1080i)(1125i)

HDTV (720p)(750p)

SDTV (480p)(525p)

VESA

–

67.5

15.6

–

31.5

1920

1080

1920

1080

1280

720

–

33.75

28.13

60 Interlace

50 Interlace

60 Progressive

59.94 Progressive

31.47

75.0

1600

1200

1600

1200

1600

1200

1600

1200

–

VESA

81.3

VESA

87.5

VESA

93.75

15.734

15.625

DVD YCbCr

59.94 Interlaced

50 Interlaced

–

#: Images in above flagged with # are compressed with Advanced AccuBlend.

NOTE: Some composite sync signals may not be displayed correctly.

Signals other than those specified in the table above may not be displayed correctly. If this should happen, change

the refresh rate or resolution on your PC. Refer to Display Properties help section of your PC for procedures.

UXGA (1600

1200) is supported for separate sync signal only.

E-59

Download from Www.Somanuals.com. All Manuals Search And Download.

PC Control Codes and Cable Connection

Using Software Keyboard

PC Control Codes

Function

Code Data

POWER ON

02H 00H 00H 00H 00H 02H

POWER OFF

02H 01H 00H 00H 00H 03H

INPUT SELECT RGB 1

INPUT SELECT RGB 2

INPUT SELECT VIDEO

INPUT SELECT S-VIDEO

02H 03H 00H 00H 02H 01H 01H 09H

02H 03H 00H 00H 02H 01H 02H 0AH

02H 03H 00H 00H 02H 01H 06H 0EH

02H 03H 00H 00H 02H 01H 0BH 13H

INPUT SELECT DVI (DIGITAL)02H 03H 00H 00H 02H 01H 1AH 22H

INPUT SELECT VIEWER

PICTURE MUTE ON

PICTURE MUTE OFF

SOUND MUTE ON

02H 03H 00H 00H 02H 01H 1FH 27H

02H 10H 00H 00H 00H 12H

02H 11H 00H 00H 00H 13H

02H 12H 00H 00H 00H 14H

02H 13H 00H 00H 00H 15H

02H 14H 00H 00H 00H 16H

02H 15H 00H 00H 00H 17H

SOUND MUTE OFF

ON SCREEN MUTE ON

ON SCREEN MUTE OFF

1 to 0 and Characters

........................... Use to type in IP address or projector name

SP ...................... Inserts a space

NOTE: Contact your local dealer for a full list of PC Control Codes if needed.

BS ...................... Deletes one character backward

̇ ........................ Returns to the previous

̈ ........................ Advances to the next

Cable Connection

OK ...................... Executes the selection

Cancel ................ Cancels the selection

Communication Protocol

Baud rate ............................. 38400 bps

Data length .......................... 8 bits

Parity.................................... No parity

Stop bit ................................ One bit

X on/off ................................ None

Communications procedure . Full duplex

Drag bar ............. Use to move the software keyboard on the screen.

MODE ................ Selects one of three modes for alphabet and special

characters.

NOTE: Depending on the equipment, a lower baud rate may be recommended

for long cable runs.

PC Control Connector (D-SUB 9P)

To TxD of PC

To RxD of PC

To GND of PC

To RTS of PC

To CTS of PC

NOTE: Pins 1, 4, 6 and 9 are no used.

NOTE: Jumper “Request to Send” and “Clear to Send” together on both ends of

the cable to simplify cable connection.

E-60

Download from Www.Somanuals.com. All Manuals Search And Download.

Power: This controls the power of the projector.

On .................. Power is switched on.

Operation Using an HTTP Browser

Off .................. Power is switched off.

Overview

The use of HTTP server functions will allow control of the projector from

a web browser without the installation of special software. Please be

sure to use “Microsoft Internet Explorer 4.x” or a higher version for the

web browser. (This device uses “JavaScript” and “Cookies” and the

browser should be set to accept these functions. The setting method

will vary depending on the version of browser. Please refer to the help

files and the other information provided in your software.)

Volume: This controls the volume of the projector.

̆ .................... Increments the volume adjustment value.

̄ .................... Decrements the volume adjustment value.

Mute: This controls the mute function of the projector.

All On ............. Mutes each of the video, audio, and on-screen dis-

play functions.

NOTE:

All Off ............. Cancels the muting of each of the video, audio, and

on-screen display functions.

* The use of HTTP server functions is not available during Standby mode.

* The display’s or button’s response can be slowed down or operation may not

be accepted depending the settings of your network. Should this happen, con-

sult your network administrator.

* The projector may not respond if its buttons are repeatedly pressed in rapid

intervals. Should this happen, wait a moment and repeat. If you still can’t get

any response, pull out and then re-insert the LAN card.

* Do not use the HTTP Server functions and the Dynamic Image Utility included

on the supplied CD-ROM. Using both at the same time may result in a connec-

tion failure or slow response.

Picture On ...... Mutes the video.

Picture Off ...... Cancels the video muting.

Sound On ...... Mutes the audio.

Sound Off ...... Cancels the audio muting.

OSD On ......... Mutes the on-screen display.

OSD Off ......... Cancels the muting of the on-screen display.

Access is gained to the HTTP server functions by specifying

http:// <the projector’s IP address> /index.html

in the entry column of the URL.

Picture: Controls the video adjustment of the projector.

Brightness ̆ .. Increments the brightness adjustment value.

Brightness ̄ .. Decrements the brightness adjustment value.

Contrast ̆ ..... Increments the contrast adjustment value.

Contrast ̄ ..... Decrements the contrast adjustment value.

Color ̆ .......... Increments the color adjustment value.

Color ̄ .......... Decrements the color adjustment value.

Hue ̆ ............ Increments the hue adjustment value.

Hue ̄ ............ Decrements the hue adjustment value.

Sharpness ̆ . Increments the sharpness adjustment value.

Sharpness ̄ . Decrements the sharpness adjustment value.

Preparation Before Use

Make network connections and set up the projector and confirm that it

is complete before engaging in browser operations. (See “Setting LAN

Mode” on page E-48.)

Operation with a browser that uses a proxy server may not be possible

depending on the type of proxy server and the setting method. Although

the type of proxy server will be a factor, it is possible that items that have

actually been set will not be displayed depending on the effectiveness

of the cache, and the contents set from the browser may not be re-

flected in operation. It is recommended that a proxy server not be used

unless it is unavoidable.

The functions that can be controlled will vary depending on the sig-

nal being input to the projector.

Handling of the Address for Operation via a Browser

Regarding the actual address that is entered for the address or entered

to the URL column when operation of the projector is via a browser, the

host name can be used as it is when the host name corresponding to

the IP address of the projector has been registered to the domain name

server by a network administrator, or the host name corresponding to

the IP address of the projector has been set in the “HOSTS” file of the

computer being used.

Source Select: This switches the input connector of the projector.

RGB1 ............. Switches to the RGB 1 connector.

RGB2 ............. Switches to the RGB 2 connector.

Video ............. Switches to the Video connector.

S-Video .......... Switches to the S-Video connector.

DVI(DIGITAL) . Switches to the DVI connector

Viewer ............ Switches to the Viewer.

Example 1: When the host name of the projector has been set to

“pj.nec.co.jp”, http://pj.nec.co.jp/index.html is specified for the ad-

dress or the entry column of the URL.

LAN ................ Switches to a LAN signal.

Projector Status: This displays the condition of the projector.

Remaining Lamp Time .. Displays the remaining life of the lamp as a

percentage.

Example 2: When the IP address of the projector is “192.168.73.1”,

access is gained to the HTTP server functions by specifying

http://192.168.73.1/index.html for the address or the entry column

of the URL.

Lamp Hour Meter .......... Displays how many hours the lamp has been

used.

Structure of the HTTP Server

Projector Usage ............ Displays how many hours the projector has

been used.

Filter Usage .................. Displays how many hours the filter has been

used.

Error Status .................. Displays the status of errors occurring within

the projector.

Refresh ......................... Updates the display of the following condi-

tions.

E-61

Download from Www.Somanuals.com. All Manuals Search And Download.

6) Problems or damage caused by expendable supplies or devices

connected to the product other than those designated by NEC.

TravelCare Guide

7) Problems caused by natural consumption, wear or deterioration

of parts under normal usage conditions.

TravelCare - a service for international travelers

This product is eligible for "TravelCare", NEC's unique international war-

ranty.

Please note that TravelCare coverage differs in part from coverage un-

der the warranty included with the product.

8) Problems or damage to lamps and other expendable supplies,

included parts or optional parts.

9) Other conditions stipulated in the warranty included with the prod-

uct also apply.

Services offered with TravelCare

This warranty allows customers to receive service on their product at

the NEC and NEC-designated service stations in the countries listed

herein when temporarily traveling internationally for business or plea-

sure.

NOTE: The product can be used overseas with voltages of 100 to 120V and 200

to 240V by using a power cable suited for the standards and power source volt-

age of the country in which the product is being used.

For details on services offered by the different service stations, please

refer to the "List of TravelCare Outlets" below.

List of TravelCare Outlets

This list applies as of June 1, 2002.

For the most up-to-date information, please refer to the websites of the

service stations in the various countries on the List of TravelCare Out-

lets or to the NEC website at http://www.nec-pj.com.

1 Repair services

The product will be repaired and delivered within 10 business days,

not including shipping time.

During the term of warranty, the cost of maintenance parts, labor

costs for repairs and shipping costs within the service station's cov-

erage area are covered by the warranty.

In Europe

NEC Europe, Ltd. / European Technical Centre

Address:

Telephone:

Fax Line:

Email Address:

WEB Address:

Unit G, Stafford Park 12, Telford TF3 3BJ, U.K.

+44 1952 237000

+44 1952 237006

[email protected]

http://www.neceur.com

2 Replacement product rental service

If the customer desires, he or she can rent a replacement product

while the original product is being repaired.

Fee: US$200 for 12 days

This fee must be paid at the local service station in cash or credit

card.

The $200 rental fee is non-refundable even if the customer rents it

less than 12 days before returning.

The replacement product will be delivered within 3 business days.

If the customer did not return the replacement product within 12 days,

the customer will be charged the price of the unit.

If the customer returned the replacement product in a faulty or dam-

aged condition, the repair cost will be charged to the customer.

Note that this service is not offered in all countries and regions. Please

refer to the "List of TravelCare Outlets".

(Regions Covered)

EU:

Austria*, Belgium*, Denmark*, Finland*, France*, Germany*,

Greece*, Ireland*, Italy*, Luxembourg*, The Netherlands*,

Portugal*, Spain*, Sweden* and the United Kingdom*

Norway*, Iceland and Liechtenstein

EEA:

In North America

NEC Solutions (America), Inc.

Address:

1250 Arlington Heights Road, Itasca,

Illinois 60143, U.S.A.

+1 800 836 0655

+1 800 356 2415

[email protected]

http://www.necvisualsystems.com

Telephone:

Fax Line:

Email Address:

WEB Address:

In addition, this replacement product rental service is not offered af-

ter the product's warranty has expired.

Term of warranty

(Regions Covered)

U.S.A. *, Canada*

a. Upon presentation of the warranty or receipt received upon pur-

chase:

In Oceania

NEC Australia Pty., Ltd.

Address: New South Wales;

184 Milperra Road, Reversby 2212

Valid for the term indicated on the warranty or the normal term of

warranty for the country of purchase.

b. When only the product is brought in:

Victoria;

Valid for a period of within 14 months of the date of manufacture

indicated by the serial number attached to the product.

480 Princess Hwy Noble Park 3174

South Australia;

84A Richmond Road, Keswick 5035

Queensland;

116 Ipswich Road, Woollongabba 4102

Western Australia;

45 Sarich Court Osborne Park 6017

131 632 (from domestic)

2 When a product whose term of warranty is expired is brought in:

Repairs will be offered for a fee. In this case the customer is not

eligible for the replacement product rental service.

3 In the following cases, repairs may be charged, even if the product's

warranty is still in effect:

Telephone:

1) If the term of warranty, model name, serial number and name of

the store of purchase are not indicated on the warranty or have

been altered.

+61 8 8375 5706 (from overseas)

+61 8 8375 5757

Fax Line:

Email Address:

WEB Address:

[email protected]

http://www.nec.com.au

2) Problems or damage caused by dropping or shocks during ship-

ment or movement by the customer or by improper handling by

the customers.

(Regions Covered)

Australia*, New Zealand

3) Problems or damage caused by improper usage or unwarrant-

able alterations or repairs by the customer.

4) Problems or damage caused by fire, salt damage, gas damage,

earthquakes, lightning damage, storm or flood damage or other

natural disasters or such external factors as dust, cigarette

smoke, abnormal voltage, etc.

5) Problems or damage caused by use in hot or humid places, in

vehicles, boats or ships, etc.

E-62

Download from Www.Somanuals.com. All Manuals Search And Download.

In Asia and Middle East

NEC Viewtechnology, Ltd.

ABBA Electronics L.L.C.

Address:

Tariq Bin Ziyad Road, P.O.Box 327, Dubai,

United Arab Emirates

+971 4 371800

Address:

686-1, Nishioi, Oi-Machi, Ashigarakami-Gun,

Kanagawa 258-0017, Japan

+81 465 85 2369

Telephone:

Fax Line:

Telephone:

+971 4 364283

Fax Line:

+81 465 85 2393

Email Address:

[email protected]

Email Address:

WEB Address:

[email protected]

http://www.nec-pj.com

(Regions Covered)

United Arab Emirates

(Regions Covered)

Japan*

Samir Photographic Supplies

Address:

P.O.Box 599, Jeddah 21421, Saudi Arabia

NEC Hong Kong Ltd.

Address:

Telephone:

Fax Line:

Email Address:

+966 2 6828219

+966 2 6830820

[email protected]

11th Floor, Tower B, New Mandarin Plaza, 14

Science Museum Road,

Tsim Sha Tsui East, Kowloon, Hong Kong

+852 2369 0335

+852 2795 6618

Telephone:

Fax Line:

(Regions Covered)

Saudi Arabia

Email Address:

WEB Address:

[email protected]

http://www.nec.com.hk

NOTE: In countries designated with an asterisk(*), replacement product rental

service are offered.

(Regions Covered)

Hong Kong

NEC Taiwan Ltd.

Address:

7F, No.167, SEC.2, Nan King East Road, Taipei,

Taiwan, R.O.C.

Telephone:

+886 2 8500 1734

Fax Line:

+886 2 8500 1420

Email Address:

WEB Address:

[email protected]

http://www.nec.com.tw

(Regions Covered)

Taiwan

NEC Singapore Pte. Ltd

Address:

401 Commonwealth Drive, #07-02, Haw Par

Technocentre, Singapore 149598

+65 6 273 8333

Telephone:

Fax Line:

+65 6 274 2226

Email Address:

WEB Address:

[email protected]

http://www.nec.com.sg

(Regions Covered)

Singapore

Hyosung Data System, Ltd.

Address:

7th Floor, Cheongdam Building, 52,

Cheongdam-Dong,

Kangnam-Ku, Seoul, Korea 135-100

+82 2 510 0234

+82 2 540 3590

Telephone:

Fax Line:

Email Address:

[email protected]

(Regions Covered)

South Korea

Lenso Communication Co., Ltd.

Address:

292 Lenso House 4, 1st Floor, Srinakarin Road,

Huamark, Bangkapi, Bangkok 10240, Thailand

+66 2 375 2425

Telephone:

Fax Line:

+66 2 375 2434

Email Address:

WEB Address:

[email protected]

http://www.lenso.com

(Regions Covered)

Thailand

E-63

Download from Www.Somanuals.com. All Manuals Search And Download.

P-1/

Date:

TO: NEC or NEC's Authorized Service Station:

FM:

(Company & Name with signature)

Dear Sir (s),

I would like to apply your TravelCare Service Program based on attached registration and qualification sheet and agree with your

following conditions, and also the Service fee will be charged to my credit card account, if I don't return the Loan units within the

specified period. I also confirm following information is correct. Regards.

Application Sheet for TravelCare Service Program

Country,

product purchased :

User's Company Name :

User's Company Address :

Phone No., Fax No. :

User's Name :

User's Address :

Phone No., Fax No. :

Local Contact office :

Local Contact office Address :

Phone No., Fax No. :

User's Model Name :

Date of Purchase :

Serial No. on cabinet :

Problem of units per User :

Required Service :

(1) Repair and Return

(1) Credit Card

(2) Loan unit

Requested period of Loan unit :

Payment method :

(2) Travelers Cheque

(3) Cash

In Case of Credit Card :

Card No. w/Valid Date :

E-64

Download from Www.Somanuals.com. All Manuals Search And Download.

5. Loan Service Charges and Conditions:

Upon acceptance of this NEC Projector, Customer agrees to assume

liability for this loan unit.

Condition of your TravelCare Service Program

Enduser is requested to understand following condition of TravelCare

Service Program and fill necessary information into the application sheet.

The current cost of use of this loan unit is $200.00 USD for 12 calendar

days.

1. Service Options:

There are 3 types of "Service" available. Enduser has to understand

following condition and is required to fill in the Application Sheet.

If Customer does not return the unit within the 12 calendar days, Cus-

tomer will be charged the next highest cost up to and including the full

list price to Credit Cards, which price will be informed by NEC Autho-

rized Service Stations. Please see the attached listing of contacts for

each country to arrange for pickup of the loan unit.

1) Repair and Return:

The 'Faulty unit' is sent or collected from the customer. It is repaired

and returned within 10 days to the customer, excluding transport time.

If you return to their country of origin with the loan unit, you will be

charged additional freight to return the unit to the loaning country.

There may have a case, repair and return can't be done by NEC

Authorized Service Station, because of shortage of spare parts due

to same model is not sold in the territory.

Thank you for your understanding of this program.

2) Repair and Return with Loan: (This service is limited to some Ser-

vice Stations)

This service is offered to the Enduser, who cannot wait until their unit

is repaired.

The customer can borrow a unit for $200 up to 12 days. Customer

then sends in inoperable unit to nearest NEC Authorized Service

Station for service. In order to prevent collection problem, Enduser is

required to fill in Application Sheet.

Enduser needs to confirm the availability of the Service to NEC Au-

thorized Service Stations.

3) Loan Only:

For this service, NEC Authorized Service Station supplies the cus-

tomer with a loan unit for US$200 up to 12 days.Customer keeps the

inoperable unit and when customer returns home, customer arranges

to have the projector serviced in the home country.

2. Warranty Exclusions:

This program does not apply if the Projector's serial number has been

defaced, modified or removed.

If, in the judgement of NEC Authorized Service Station or its agent the

defects or failures result from any cause other than fair wear and tear or

NEC neglect, or fault including the following without limitation:

1) Accidents, transportation, neglect, misuse, abuse, water, dust, smoke

or default of or by the Customer its employees or agents or any third

party;

2) Failure or fluctuation of electrical power, electrical circuitry, air condi-

tioning, humidity control or other environmental conditions such as

use it in smoking area;

3) Any fault in the attachments or associated products or components

(whether or not supplied by NEC or its agents which do not form part

of the Product covered by this warranty);

4) Any act of God, fire, flood, war, act of violence or any similar occur-

rence;

5) Any attempt by any person other than any person authorized by NEC

to adjust, modify, repair, install or service the product.

6) Any Cross-border charges such as, duty, insurance, tax etc.

3. Charges for Warranty Exclusions and Out of Warranty Case:

In case faulty unit is under warranty exclusions case or under Out of

Warranty period, NEC Authorized Service Station will Inform estimation

of actual service cost to the Enduser with reason.

4. Dead on Arrival (DOA):

Enduser must take this issue up with their original supplier in the coun-

try of purchase.

NEC Authorized Service Station will repair the DOA unit as a Warranty

repair, but will not exchange DOA unit with new units.

E-65

Download from Www.Somanuals.com. All Manuals Search And Download.

Printed in Japan

7N8P1912

Download from Www.Somanuals.com. All Manuals Search And Download.

Miller Electric Welder DS 64M Swingarc User Manual
National Instruments Computer Accessories 321518A 01 User Manual
NETGEAR Network Hardware WN604 100NAS User Manual
Nilfisk ALTO Vacuum Cleaner R 680 P User Manual
Nintendo Video Games 45496902971 User Manual
Nokia Bluetooth Headset BH 903 User Manual
NordicTrack Home Gym NTMC29931 User Manual
Nortel Networks Switch movianVPN User Manual
OPTI UPS Power Supply DS1000B User Manual
Panasonic Electronic Keyboard 970 User Manual