P r i n t e d i n J a p a n
P a r t N o . 7 8 4 0 9 9 4 2
I t a s c a , I l l i n o i s 6 0 1 4 3 - 1 2 4 8
1 2 5 0 N . A r l i n g t o n H e i g h t s R o a d ,
N E C T e c h n o l o g i e s , I n c .
S u i t e 5 0 0
o j e c t o r t a b l e P r U l t r a - P o r
Ultra-Portable Projector
®
MultiSync LT81™/100™
Projector
User’s Manual
NEC Technologies
Download from Www.Somanuals.com. All Manuals Search And Download.
3
Important Safeguards
These safety instructions are to ensure the long life of your projector and to
prevent fire and shock. Please read them carefully and heed all warnings.
7. If installing the projector on the ceiling:
a. The ceiling must be strong enough to support the projector and the
installation must be in accordance with any local building codes.
Installation
1. For best results, use your projector in a darkened room.
b. The projector must be installed by qualified NEC service personnel.
2. Place the projector on a flat, level surface in a dry area away from dust and
moisture.
Power Supply
1. The projector is designed to operate on a power supply of 100-120 or 220-240
V 50/60 Hz AC. Ensure that your power supply fits this requirement before
attempting to use your projector.
3. Do not place your projector in direct sunlight, near heaters or heat radiating
appliances.
4. Exposure to direct sunlight, smoke or steam can harm internal components.
5. Handle your projector carefully. Dropping or jarring can damage internal
components.
2. Handle the power cable carefully and avoid excessive bending. A damaged
cord can cause electric shock or fire.
6. Do not place heavy objects on top of the projector.
3. If the projector is not to be used for an extended period of time, disconnect the
plug from the power outlet.
Cleaning
Fire and Shock Precautions
1. Unplug the projector before cleaning.
1. Ensure that there is sufficient ventilation and that vents are unobstructed to
prevent the build-up of heat inside your projector. Allow at least 3 inches
(10cm) of space between your projector and a wall.
2. Clean the cabinet periodically with a damp cloth. If heavily soiled, use a mild
detergent. Never use strong detergents or solvents such as alcohol or thinner.
3. Use a blower or lens paper to clean the lens, and be careful not to scratch or
mar the lens.
2. Prevent foreign objects such as paper clips and bits of paper from falling into
your projector. Do not attempt to retrieve any objects that might fall into your
projector. Do not insert any metal objects such as a wire or screwdriver into
your project. If something should fall into your projector, disconnect it
immediately and have the object removed by a qualified NEC service person.
Lamp Replacement
• Perform lamp replacement in accordance with the instructions on page 81.
3. Do not place any liquids on top of your projector.
• Be sure to replace the lamp when the Status light comes on. If you continue
to use the lamp after 1000 hours of use, the lamp bulb may shatter, and pieces
of glass may be scattered in the lamp case. Do not touch them as the pieces of
glass may cause injury. If this happens, contact your NEC dealer for lamp
replacement.
• Do not look into the lens while the projector is on. Serious
damage to your eyes could result.
• Do not look into the laser pointer while it is on and do not point
the laser beam at another person. Serious injury could result.
• Allow a minimum of ONE minute to elapse between turning the lamp off and
on. High voltage is applied to the lamp immediately when the power is turned
on. Therefore turning the power off and quickly back on may shorten the life
of your lamp and result in damage to your projector.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
5
ATTENTION
RISQUE D’ELECTROCUTION NE PAS OUVRIR
ATTENTION
Pour couper l'alimentation principale, s'assurer de retirer la fiche de la prise de courant.
La prise de courant murale doit être installée le plus près possible de l'équipement, et doit être facilement accessible.
Télécommande LT100
Télécommande LT81
ATTENTION
RAYONNEMENT LASER NE PAS
REGARDER DANS LE FAISCEAU
ATTENTION
RAYONNEMENT LASER NE PAS
REGARDER DANS LE FAISCEAU
LONGUEUR D’ONDE: 645 nm (640-660 nm)
MAX. SORTIE: 1 mW
APPREIL A LASER DE CLASSE 2
LONGUEUR D’ONDE: 670 nm
MAX. SORTIE: 1 mW
APPREIL A LASER DE CLASSE 2
DOC avis de conformation
Ce symbole a pour but de prévenir l’utilisateur de la
présence d’une tension dangereuse, non isolée se
trouvant à l’intérieur de l’appareil. Elle est d’une
intensité suffisante pour constituer un risque
d’électrocution. Eviter le contact avec les pièces à
l’intérieur de cet appareil.
DOC avis de conformation
Cet appareil numérique de la classe A respecte toutes les exigences du
Règlement sur le Matériel Brouilleur du Canada.
Ce symbole a pour but de prévenir l’utilisateur de la
présence d’importantes instructions concernant
l’entretien et le fonctionnement de cet appareil. Par
conséquent, elles doivent être lues attentivement afin
d’éviter des problèmes.
Importantes précautions de sécurité
Les points suivants sont des précautions de sécurité importantes destinées à
garantir une longue durée de service du projecteur et afin d’éviter un incendie
et des risques d’électrocution. S’assurer de lire attentivement ces précautions de
sécurité et respecter tous les avertissements décrits ci-dessous.
AVERTISSEMENT
Installation
AFIN DE REDUIRE LES RISQUES D’INCENDIE OU D’ELECTROCUTION,
NE PAS EXPOSER CET APPAREIL A LA PLUIE OU A L’HUMIDITE. AUSSI,
NE PAS UTILISER LA FICHE POLARISEE AVEC UN PROLONGATEUR OU
UNE AUTRE PRISE DE COURANT SAUF SI CES LAMES PEUVENT ETRE
INSEREES A FOND. NE PAS OUVRIR LE COFFRET, DES COMPOSANTES
HAUTE TENSION SE TROUVENT A L’INTERIEUR. LAISSER A UN PER-
SONNEL QUALIFIE LE SOIN DE REPARER CET APPAREIL.
1. Pour un fonctionnement optimal, utiliser le projecteur dans une pièce sombre.
2. Placer le projecteur sur une surface à niveau et dans un endroit sec exempt de
poussières et d’humidité.
3. Ne pas placer le projecteur en plein soleil, près d’appareils ménagers ou
d’autres appareils de chauffage.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
7
4. La fumée, la vapeur et l’exposition aux rayons directs du soleil risquent de
détériorer sérieusement les composantes internes.
3. Si le projecteur n’est pas utilisé pendant une période prolongée, retirer la fiche
de la prise secteur.
5. Eviter des manipulations brusques lors du déplacement du projecteur, car un
choc violent pourrait endommager les composantes internes.
Nettoyage
6. Ne pas deposer d’objets lourds sur le dessus du projecteur.
1. Débrancher le projecteur de la prise d’alimentation avant le nettoyage.
7. Lors de l’installation du projecteur au plafond, respecter les instructions
suivantes.
2. Nettoyer régulièrement le coffret avec un chiffon doux. S’il y a des taches
tenaces, utiliser une solution d’un détergent doux. Ne jamais utiliser de
détergents puissants ou des solvants, tel que l’alcool ou un diluant pour
nettoyer le projecteur.
a. Le plafond doit être suffisamment solide pour supporter le poids du
projecteur et il doit être installé selon les codes de construction locaux.
b. Le projecteur doit être installé par un personnel qualifié.
3. Utiliser un appareil diffuseur chauffant ou du papier de nettoyage de lentille
disponible dans le commerce pour nettoyer la lentille.
Alimentation
1. Le projecteur est conçu pour fonctionner à 100-120 ou 220-240VCA 50/
60Hz. S’assurer que la tension d’alimentation locale satisfait cette exigence
avant d’utiliser le projecteur.
Ne pas frapper ou rayer la surface de la lentille, car des défauts risquent de se
produire sur la surface de la lentille.
2. Manipuler le câble d’alimentation avec précaution et éviter de le plier
excessivement. Un cordon endommagé risque de provoquer une
électrocution ou un incendie.
2. Eviter que des objets étrangers, des agrafes, des clous et du papier, par
exemple, pénètrent à l’intérieur du projecteur. Ne pas essayer de récupérer
ces objets soi-même ou ne pas insérer des objets métalliques, des fils et des
tourne-vis, par exemple à l’intérieur du projecteur. Si un objet tombe à
l’intérieur du projecteur, le débrancher immédiatement et contacter un
dépanneur qualifié pour retirer l’objet.
Remplacement de la lampe
• Effectuer le remplacement de la lampe suivant les instructions de la page 85.
• Assurez-vous de bien remplacer la lampe lorsque le voyant d’usure
s’allume. Si vous continuez d’utiliser la lampe après 1000 heures
d’utilisation, l’ampoule peut se briser et des brisures de verre peuvent être
éparpillées dans le compartiment de la lampe. Ne les touchez pas car elles
peuvent vous blesser. Dans ce cas, contactez votre revendeur NEC afin de
procéder au remplacement de la lampe.
3. Ne pas placer des liquides sur le dessus du projecteur.
• Ne regardez pas à l’intérieur de l’objectif lorsque le projecteur
est en marche. Vous risquez de vous blesser gravement aux
yeux.
• Attendez minimum UNE minute après avoir éteint la lampe avant de la
rallumer. Une haute tension est immédiatement appliquée à la lampe quand
celle-ci est mise sous tension. Par conséquent, éteindre, puis tout de suite
rallumer peut abréger la vie de votre lampe et endommager votre projecteur.
• Ne regardez pas à l’intérieur de la flèche laser lorsque celle-ci
est en marche et ne dirigez pas le rayon laser sur une autre
personne. Vous risquez de provoquer ue blessure grave.
Précautions pour éviter un incendie ou
une électrocution
1. Une ventilation appropriée doit être assurée afin d’éviter une accumulation
de chaleur à l’intérieur du projecteur. S’assurer que les trous de ventilation ne
sont pas obstrués. Laisser un espace d’au moins 10 cm (quatre pouces) entre
le projecteur et les murs.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
9
L I M I T E D W A R R A N T Y
®
2. Any product on which the serial number has been defaced, modified or
removed. NECTECH’S LIABILITY FOR ANY DEFECTIVE PRODUCT
IS LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT
AT OUR OPTION. REPLACEMENT PRODUCTS MAY BE NEW OR
‘LIKE NEW’.
NEC MultiSync Projector
Products
NEC Technologies, Inc. (hereafter NECTECH) warrants this product to be free
from defects in material and workmanship under the following terms.
3. NECTECH SHALL NOT BE LIABLE FOR : Damage, deterioration or
malfunction resulting from:
HOW LONG IS THE WARRANTY?
Parts and labor are warranted for (2) two years from the date of the first customer
purchase. The lamp is warranted for 1000 hours of operating time or six months,
whichever comes first.
a. Accident, misuse, abuse, neglect, fire, water, lightning or other acts of
nature, unauthorized product modification, or failure to follow instructions
supplied with the product.
WHO IS PROTECTED?
b. Repair or attempted repair by anyone not authorized by NECTECH.
c. Any shipment of the product (claims must be presented to the carrier).
d. Removal or installation of the product.
This warranty may be enforced only by the first purchaser.
WHAT IS COVERED AND WHAT IS NOT COVERED
Except as specified below, this warranty covers all defects in material or
workmanship in this product. The following are not covered by the warranty:
e. Any other cause which does not relate to a product defect.
1. Any product which is not distributed in the U.S.A. or Canada by NECTECH
or which is not purchased in the U.S.A. or Canada from an authorized
NECTECH dealer. For a listing of authorized dealers please contact
NECTECH at 800-836-0655.
4. Cartons, carrying cases, batteries, external cabinets, magnetic tapes, or any
accessories used in connection with the product.
WHAT NEC WILL COVER
We will pay labor and material expenses for covered items. But we will not pay
for the following:
1. Removal or installation charges.
2. Costs of initial technical adjustments (set-up), including adjustment of user
controls. These costs are the responsibility of the NECTECH dealer from
whom the product was purchased.
1. DAMAGE TO OTHER PROPERTY CAUSED BY ANY DEFECTS IN
THIS PRODUCT, DAMAGES BASED UPON INCONVENIENCE, LOSS
OF USE OF THE PRODUCT, LOSS OF TIME, COMMERCIAL LOSS;
OR
3. Payment of shipping charges.
2. ANY OTHER DAMAGES, WHETHER INCIDENTAL, CONSEQUEN-
TIAL OR OTHERWISE. SOME STATES DO NOT ALLOW LIMITA-
TIONS ON HOW LONG AN IMPLIED WARRANTY LASTS AND/OR
DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDEN-
TAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITA-
TIONS AND EXCLUSIONS MAY NOT APPLY TOYOU.
HOW YOU CAN GET WARRANTY SERVICE
1. To obtain service on your product, consult the dealer from whom you
purchased the product.
2. Whenever warranty service is required, the original dated invoice (or a copy)
must be presented as proof of warranty coverage. Please be prepared to
describe or demonstrate the problem to your dealer.
HOW STATE LAW RELATES TO THE WARRANTY
This warranty gives you specific legal rights, and you may also have other rights
which vary from state to state.
3. For the name of the nearest NECTECH authorized service center, call
NECTECH at 800-836-0655.
FOR MORE INFORMATION, TELEPHONE 800-366-5213
LIMITATION OF IMPLIED WARRANTIES
ALL IMPLIED WARRANTIES, INCLUDING WARRANTIES OF MER-
CHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE
LIMITED IN DURATION TO THE LENGTH OF THIS WARRANTY.
NEC TECHNOLOGIES, INC.
1250 N. Arlington Heights Road, Suite 500
Itasca, Illinois 60143-1248
EXCLUSION OF DAMAGES
NECTECH’S LIABILITY FORANY DEFECTIVE PRODUCT IS LIMITED
TO THE REPAIR OR REPLACEMENT OF THE PRODUCT AT OUR
OPTION. NECTECH SHALL NOT BE LIABLE FOR:
NOTE: All products returned to NECTECH for service MUST have
prior approval. To get approval, call NEC Technologies at
800-836-0655.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
T A B L E O F C O N T E N T S
11
1. Introduction
Introduction To The MultiSync LT81/LT100 Projector .................................... 13
How Do You Get Started? ................................................................................ 15
What’s In The Box? ......................................................................................... 15
Getting To Know Your MultiSync LT81/LT100 Projector ................................ 17
Front Features ........................................................................................... 17
Rear Features ............................................................................................ 18
Top Features .............................................................................................. 19
Terminal Panel Features ............................................................................ 21
Remote Control Features ........................................................................... 25
2. Installation
Setting Up Your MultiSync LT81/LT100 Projector .......................................... 29
Selecting A Location ................................................................................. 30
Projection Distance ................................................................................... 31
Using A Tabletop Or Cart .......................................................................... 35
Transporting And Storing The Projector .................................................... 37
Ceiling Installation .................................................................................... 41
Wiring Diagram ............................................................................................... 43
ConnectingYour PC Or Macintosh Computer ................................................. 45
ConnectingYour DVD Player .......................................................................... 51
ConnectingYour Document Camera ................................................................ 51
ConnectingYour VCR Or Laser Disc Player .................................................... 52
Connecting An External Monitor ..................................................................... 52
ConnectingYour Remote Mouse Receiver ....................................................... 53
3. Operation
General Controls.............................................................................................. 57
Using The Menus ............................................................................................ 59
Menu Descriptions & Functions ...................................................................... 61
Source Menu (Source Icons) ..................................................................... 61
Image Adjust Menu(Sound And Picture Control Icons) ............................. 63
Power Menu(Projector Control Icons) ..................................................... 67
Settings Menu(Maintenance Icons) ........................................................... 69
Using the Viewer Function ........................................................................ 71
4. Maintenance
Replacing The Lamp ....................................................................................... 81
Remote Control Battery Installation ................................................................ 83
Operating Range .............................................................................................. 84
5. Troubleshooting
Status Light Messages ..................................................................................... 89
Common Problems & Solutions ...................................................................... 91
6. Specifications
Optical / Electrical / Mechanical ...................................................................... 93
Cabinet Dimensions ........................................................................................ 95
D-Sub Pin Assignments ................................................................................... 99
Timing Chart ................................................................................................. 101
PC Control Command Reference ................................................................... 103
Cable Connection .......................................................................................... 107
12
Download from Www.Somanuals.com. All Manuals Search And Download.
1 I N T R O D U C T I O N
13
This section introduces you to your new MultiSync LT81 (SVGA)/
LT100 (XGA) Projector, provides a list of materials that comes with
your projector and describes the features and controls.
Features you'll enjoy:
•
•
Simple set up and operation.
A high-performance 280 watt metal halide lamp that delivers a high
bright image, allowing you to make presentations with the lights on.
•
A wireless remote control that operates the projector from any
angle.
Congratulations On Your Purchase Of The
MultiSync LT81/LT100 Projector
•
•
A laser pointer that' s built into the remote control.
The MultiSync LT81/LT100 is one of the very best projectors available
today. The MultiSync LT81/LT100 enables you to project precise
images up to 300 inches across (measured diagonally) from your PC or
Macintosh computer (desktop or notebook), VCR, DVD player, docu-
ment camera, or even a laser disc player.
The manual zoom control enables you to adjust the image to be
between 24 and 300 inches (measured diagonally).
•
•
White balance control allows you to adjust the brightness and
contrast for each RGB color.
You can choose between video modes depending on your source:
You can use the projector on a tabletop or cart, you can permanently
"normal" for a typical picture, "natural" for true color reproduction,
and "camera" for use with a document camera or low APL picture.
mount it on a ceiling*1, or you can use MultiSync LT81/LT100 Projec-
tor to project images from behind the screen. The remote control can be
used wirelessly or with a cable (only the LT100 can be connected with
a cable), and you can even use the remote control with the built-in
remote mouse receiver to operate the mouse on your PC or Mac.
•
•
The optional LT Viewer kit allows you to start your presentation
even when a PC is not available at the site.
The "image capture" enables you to use the entire picture as a
background image or to create slides (optional LT Viewer required).
•
•
An image can be projected from in front or behind a screen, and the
projector can even be installed on the ceiling.
•
•
Accepts component video source such as DVD player with the Y/
Cb/Cr output.
NEC Technologies' exclusive AccuBlend™ intelligent pixel blend-
ing technology - an extremely accurate image compression technol-
ogy - offers a crisp image with SXGA (1280
ן 1024) resolution*2 . Supports most IBM VGA, SVGA, XGA*3, SXGA(with
AccuBlend™)*2 , Macintosh, or any other RGB signals within a
horizontal frequency range of 15.754 to 85 kHz (60 kHz : LT81) and
a vertical frequency range of 50 to 85 Hz. This includes NTSC,
PAL, SECAM and NTSC4.43 standard video signals.
The remote control can be used with (LT100 only) or without a
cable, and you can even use the remote to operate your PC or
Macintosh mouse wirelessly from across the room with the built-in
remote mouse receiver.
•
•
•
You can control your MultiSync LT81/LT100 Projector with a PC.
The contemporary cabinet design is compact, easy to carry, and
complements any office, board room or auditorium.
*1 Installing the MultiSync LT81/LT100 LCD Projector on the ceiling
must be done by authorized NEC technicians. Consult your NEC
dealer for more information.
Note: Composite video standards are as follows:
NTSC:
PAL:
U.S. TV standard for video in U.S. and Canada.
TV standard used in western Europe.
*2 An SXGA image (1280
ן 1024) is converted into a 1024ן 768 SECAM:
NTSC4.43:
TV standard used in France and Eastern Europe.
TV standard used in Middle East countries.
crisp image with NEC technology's AccuBlend on LT100.
*3 An XGA image (1024
ן 768) is converted into an 800ן 600 crisp image with NEC technology's AccuBlend.
INTRODUCTION
14
Download from Www.Somanuals.com. All Manuals Search And Download.
15
Remote control
Mouse adapter (For IBM PS/2)
How Do You Get Started?
The fastest way to get started is to take your time and do everything
right the first time. Take a few minutes now to click through the
training CD-ROM and review the user’s manual. This may save you
hours later on. At the beginning of each section of the manual you'll
find an overview. If the section doesn't apply, you can skip it.
What’s In The Box?
Make sure your box contains everything listed. If any pieces are missing,
contact your dealer. Please save the original box and packing materials if
you ever need to ship your MultiSync LT81/LT100 Projector.
Mouse adapter (For Macintosh)
Remote control case
• NEC MultiSync LT81/LT100
Projector
•
MouseAdapters for IBM PS/2 and Mac
• Serial Cable
• Carrying Case
• Remote Control With Built-In
Laser Pointer
• Remote Cable (LT100 only)
• Remote Control Case
• Remote Mouse Receiver
• Signal Cable
• Pin Adapter for Macintosh
• Power Cable
• Two AA Batteries
• Introductory / Training CD-ROM
• User's Manual
Pin adapter for
Macintosh
Batteries (AA
ן 2) Remote mouse receiver
• Registration Card
• Quick Connect Guide
(15-Pin Mini D-Sub To 15-Pin
Mini D-Sub Connector)
Signal cable
Serial cable
Remote Cable (LT100 only)
Carrying case for LT100
Power cable
(15-Pin Mini D-Sub To 15-Pin Mini
D-Sub connector)
Introductory / Training CD-ROM
Quick Connect Guide
User’s manual
Registration card
Carrying case for LT81
Quick Cect Gide
MultiSync LT
Ultra-Portable
MultiSync
Projector
81/100
INTRODUCTION
16
Download from Www.Somanuals.com. All Manuals Search And Download.
17
Getting To Know Your MultiSync LT81/LT100 Projector
Top features
Monaural Speaker (1W)
Front Features
O N
/ O F F
E N T E R
P O W E R
S T A T U S
S E L E C T
M E M U
Cooling Fan
Rear Foot
Remote Sensor
Ventilation
One-Touch Tilt Button (LT100 only)
Adjustable Foot
(Adjustable on LT100 only)
Lens and lens Cap
Focus Ring
Terminal Panel
Remote Sensor
Zoom Ring Lever
One-Touch Tilt Button (LT100 only)
Adjustable Foot
Rear Features
Lever-type Rear Foot (LT81 only)
Remote Sensor
MEMU
Remote Sensor
Carrying handle
SELECT
STATUS
POWER
ENTER
/OFF
ON
Slot for Kensington MicroSaver Security
System
AC IN
Power Switch
AC Input
The above drawings show LT100 but most information
in this user’s manual applies to both products.
Connect the supplied power
cable’s three-pin plug here.
INTRODUCTION
18
Download from Www.Somanuals.com. All Manuals Search And Download.
19
Top Features
1 Power Button
Use this button to turn the power on and off when Main Power Switch is
on and the projector is on standby.
MEMU
2 Enter Button
SELECT
STATUS
POWER
ENTER
Executes your menu selection.
/OFF
ON
3 Select (▲▼ᮤ ᮣ) / (+)(–) Buttons
Select: After you press the “Menu” button, use the ▲ or ▼ button to
AC IN
ᮤ ᮣ
(▲▼
)
select the menu icon of the item you wish to adjust.
(+)(–): Use these buttons while you' re in the Image Adjust mode to
change the level of a selected menu item. These buttons are also
used to set an item in the Power or Settings menus.
4 Menu Button
Displays the on- screen menu.
5 Power Indicator
When the projector is switched On, the green LED blinks for about one
minute, then lights up.
4
3
If the main power is on and you switch it off by pressing POWER
OFF on the remote control or press and hold down the POWER
button on the cabinet for one second, the green LED blinks for
one minute, then lights up and the projector goes on standby.
MENU
SELECT
-
+
* The projector will not accept operation instructions for the one
minute during which the LED is blinking during switching on
or off as described above.
2
6
ENTER
6 Status Indicator
STATUS
POWER
When this is lit red continually, it's warning you that the projec-
tion lamp has exceed 1000 hours of service. After this light ap-
pears, it is advisable to replace the projection lamp as soon as
possible.(See page 81.)
ON/OFF
5
1
When the operating time of the lamp exceeds 1000 hours, the STA-
TUS indicator is lit red continually. In addition the message "LAMP
USAGE XX HOURS" appears continually when the on-screen
menu is not displayed.
If this light blinks red rapidly, it indicates that the lamp house is
not attached properly; if the light blinks slowly it means the pro-
jector's internal temperature is too hot to operate safely. See the
Status Light Messages on page 89 for more details.
INTRODUCTION
20
Download from Www.Somanuals.com. All Manuals Search And Download.
21
Terminal Panel Features
This panel is located in the side and is where you connect your cables.
2
3
1
1 Remote Control Jacks (LT100 only)
a. Remote Control Input Jack
Connect your remote control cable here for wired operation.
INPUT
VIDEO INPUT
b. Remote Control Output Jack
This terminal enables you to operate up to five projectors with the
same remote control. When your remote mouse receiver is con-
nected here, the remote sensors on the projector cabinet will re-
ceive your mouse commands.
(
)
S-VIDEO
RGB INPUT
VIDEO L MONO
-
R-
AUDIO
OUTPUT
PC CONTROL
OUTPUT
OUTPUT
REMOTE
CONTROL
2 Video Input
RGB
AUDIO
RGB
AUDIO
Connect a VCR, laser disk player, DVD player, or document cam-
era here to project video.
Left Channel/Mono Audio Input Jack
4
This is your left channel audio input for stereo sound coming from
video equipment or audio system. This also serves as your mon-
aural audio input.
Right Channel Audio Input Jack
This is your right channel audio input for stereo sound.
S-Video Input
Here is where you connect S-Video input from an external source
like a VCR.
NOTE: S-Video provides more vivid color and higher resolution than
the traditional composite video format.
3 PC Control Port
Use this port to connect your PC to control the MultiSync LT81/
LT100 Projector. This enables you to use your PC and serial com-
munication protcol to control the projector. If you are writing your
own program, command reference are on pages 103 to 106.
4 RGB Input Connector (Mini D-Sub 15 pin)
Connect your PC or other RGB equipment such as IBM or com-
patible computers. Use the signal cable that's supplied to connect
to a PC. This also serves as the Y/Cb/Cr input connector which
allows you to connect a DVD player with the component video
output.
RGB Audio Input Mini Jack
This is where you connect RGB audio output from a computer or
another RGB source.
INTRODUCTION
22
Download from Www.Somanuals.com. All Manuals Search And Download.
23
5 RGB Output Connector (Mini D-Sub 15 pin)
You can use this connector to loop your computer image to an
external monitor from the RGB input source.
INPUT
VIDEO INPUT
(
)
S-VIDEO
VIDEO L MONO
-
R-
AUDIO
OUTPUT
PC CONTROL
OUTPUT
Even if VIDEO is selected, the video image input to the RGB
INPUT terminal is output.
OUTPUT
RGB INPUT
REMOTE
CONTROL
Audio Output Mini Jack
RGB
AUDIO
RGB
AUDIO
You can use this jack to loop your audio to an external monitor
from the VIDEO audio input or RGB audio input source.
5
6 Built-in Security Slot (
)
This security slot supports the MicroSaver® Security System.
MicroSaver® is a registered trademark of Kensington Microware
MEMU
Inc. The logo
Microware Inc.
is trademarked and owned by Kensington
SELECT
STATUS
POWER
ENTER
/OFF
ON
6
AC IN
INTRODUCTION
24
Download from Www.Somanuals.com. All Manuals Search And Download.
25
3
Remote Control Features
You can use your wireless remote control to operate your MultiSync LT81/
LT100 Projector. With the remote mouse receiver connected to your computer,
you can also use the projector’s remote control to operate your computer. (See
pages 53 to 56 to connect the remote mouse receiver to your computer.)
2
NOTE: If you are using a Macintosh computer, you can click either the right or
left button to activate the mouse.
1
1 Left Click Button
4
5
Use this button to enter your menu selection. It works the same as the
"Enter" button on the cabinet.
2 Laser Pointer
OFF
POWER
ON
Beams a laser light when “Laser” button is pressed.
VIDEO S-VIDEO
3 Infrared Transmitter
6
7
8
Direct the remote control toward the remote sensor on the projector cabinet
or the remote mouse receiver.
RGB
PC CARD
9
4 LED
Flashes when any button is pressed.
MENU
LASER
10
-
+
5 Power On And Off
If your main power switch is turned on, you can use these buttons to turn
your MultiSync LT81/LT100 Projector on and off.
6 Video Button
R-CLICK
POSITIONPIC-MUTE FREEZE
Press to select an NTSC, PAL, SECAM or NTSC4.43 compatible video
source from a VCR, DVD player, laser disc player or document camera.
7 S-Video Button
MAGNIFY SLIDE VOLUME
Press to select an S-Video source from a VCR or other S-Video source.
+
+
+
8 RGB Button
- - -
Press to select a video source from a computer connected to your RGB port.
9 PC Card Button
Press to display a slide from the flash memory card inserted in the PC card
slot of your projector. (You must first install the optional LT Viewer board
into your projector.)
10 Menu Button
Use this button to call up the On-Screen Menu so you can adjust and set
the image. After you press this button, it will light up. During this time
you can use the mouse pointer and right/left click buttons to make
menu selections. If no buttons are pressed within 10 seconds the menu
turns off.
INTRODUCTION
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
11 Laser Button
Press and hold this button to activate the laser pointer. When lit, you can use
the laser to draw your audience's attention to a red dot that you can place on
any object within 30 feet (10 m).
OFF
POWER
ON
VIDEO S-VIDEO
12 Mouse Pointer Buttons
Works as a mouse for your computer. This button is also used to adjust
screen position. Push (+) or (–) to select the submenu you want to adjust.
RGB
PC CARD
13 Right Click Button
MENU
LASER
Press this button to exit "Menus" or "Position."
14 Freeze Button
11
12
This button will freeze a video image. Press again to resume motion.
15 Position Button
-
+
When image is magnified, press this button to activate the mouse. This
allows you to select the portion of the image displayed on screen. Position
button will remain lit for 10 seconds or until right click button is pushed.
13
15
NOTE: When you are adjusting Position, the Mouse Pointer button is used to
move the picture.
R-CLICK
POSITIONPIC-MUTE FREEZE
14
16
16 Picture Mute Button
This button turns off the image and sound for a short period of time.
Press again to restore the image and sound.
MAGNIFY SLIDE VOLUME
+
+
+
- - -
17 Magnify Button
Use the (+) or (–) button to adjust the image size up to 400%.
18 Slide Button
17
19
Press (+) to advance the next file or slide and (-) to return to the
previous file or slide. (the optional LT Viewer board required)
19 Volume Buttons
Press (+) to increase the volume and (–) to decrease it.
18
20 Remote Jack (LT100 only)
OF
Connect your remote control cable here for wired operation.
VIDEO
S-
VI
RGB
NOTE: You cannot use Menu and Position at the same time.
MENU
PC CARD
LASER
Remote Control Precautions
POSITION
•
•
•
•
•
•
Do not look into the laser pointer while it is on.
Do not point the laser beam at a person.
Handle the remote control carefully.
If the remote control gets wet, wipe it dry immediately.
Avoid excessive heat and humidity.
R-CLICK
PIC-MUTE
+
MAGNIFY
FREEZE
+
SLIDE
+
VOLUME
+
If you will not be using the remote control for a long time, remove the
batteries.
20
•
Do not mix new and old or different types of batteries.
INTRODUCTION
28
Download from Www.Somanuals.com. All Manuals Search And Download.
2 I N S T A L L A T I O N
29
This section describes how to set up your MultiSync LT81/LT100 projector
and how to connect video and audio sources.
Setting Up Your MultiSync LT81/LT100 Projector
Your MultiSync LT81/LT100 Projector is simple to set up and use. But before
you get started, you must first:
1. Determine the image size
MEMU
2. Set up a screen or select a non-glossy white wall onto which you can project
your image.
SELECT
STATUS
POWER
ENTER
/OFF
ON
AC IN
Carrying The Projector Always carry your projector by the handle. Ensure
that the power cord and any other cables connecting to video sources are
disconnected before moving the projector. When moving the projector or
when it is not in use, cover the lens with the lens cap.
Carrying handle
Pull it out ; push it back to retract.
Selecting A Location The further your projector is from the screen or wall, the
larger the image. The minimum size the image can be is approximately 24"
(0.61 m) measured diagonally when the projector is roughly 4 feet (1.2 m)
from the wall or screen. The largest the image can be is 300" (7.6 m) when
the projector is about 40.35 feet (12.3 m) from the wall or screen.
Projection Distance and Image Size
300
300”
231”
240
200
160
120
100
80
60
40
20
0
WIDE
TELE
27”
24”
Projection distance
Width
ft.
0.0 3.28 6.56 9.84 13.12 16.4 19.7 23.0 26.2 29.5 32.8 36.1 39.4 40.35
(1) (2) (3) (4) (5) (6) (7) (8) (9) (10) (11) (12) (12.3) (m)
Projection Distance
Screen size
Height
(diagonal)
INSTALLATION
30
Download from Www.Somanuals.com. All Manuals Search And Download.
31
Projection Distance
Wide
Screen size
inch
40”
60”
14.8
48
70”
14.7
56
80”
14.7
64
90”
14.6
72
100”
14.6
80
120”
14.6
96
150”
14.6
120
180”
14.5
144
200”
14.5
160
240”
14.5
192
270”
14.5
216
300”
14.5
240
Projection angle α Degree 14.8
Screen width H
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
32
813
65.2
1219 1422 1626 1829 2032 2438 3048 3658 4064 4877 5486 6096
97.8 114.8 131.6 148.3 164.8 198.5 248.7 298.9 332.3 399.2 449.4 500.2
A
B
C
D
E
1655 2483 2915 3342 3767 4185 5042 6316 7591 8441 10140 11415 12704
4.7
119
63
7.0
178
94.5
8.2
207
111
9.3
10.5
267
11.7
296
14.0
356
17.5
444
21.0
533
23.3
593
28.0
711
31.5
800
35.0
889
237
Projection distance
127.3 143.5 159.4 192.1 240.7 289.3 321.7 386.5 435.1 484.3
1600 2400 2819 3233 3645 4049 4879 6114 7348 8171 9817 11052 12301
12
305
24
18
457
36
21
533
42
24
610
48
27
686
54
30
762
60
36
914
72
45
1143 1372 1524 1829 2057 2286
90 108 120 144 162 180
54
60
72
81
90
610
914
1067 1219 1372 1524 1829 2286 2743 3048 3658 4115 4572
Tele
40”
11.4
32
60”
11.4
48
70”
11.4
56
80”
11.4
64
90”
11.3
72
100”
11.3
80
120”
11.3
96
150”
11.3
120
180”
11.3
144
200”
11.3
160
240”
11.2
192
270”
11.2
216
300”
–
Screen size
inch
Projection angle α Degree
–
Screen width H
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
inch
mm
813
1219 1422 1626 1829 2032 2438 3048 3658 4064 4877 5486
–
84.4 126.5 147.2 168.7 190.8 212.8 255.2 319.6 384.0 426.3 512.7 577.2
2143 3213 3739 4286 4847 5406 6483 8117 9753 10829 13024 14660
–
A
B
C
D
E
–
4.7
119
82.7
7.0
178
124
8.2
9.3
10.5
267
11.7
296
14.0
356
17.5
444
21.0
533
23.3
593
28.0
711
31.5
800
–
207
237
–
144.3 165.4 187.1 208.7 250.3 313.4 376.6 418.1 502.9 566.1
–
Projection distance
2101 3150 3665 4201 4752 5301 6358 7960 9566 10620 12774 14379
–
12
305
24
18
457
36
21
533
42
24
610
48
27
686
54
30
762
60
36
914
72
45
1143 1372 1524 1829 2057
90 108 120 144 162
54
60
72
81
–
–
–
610
914
1067 1219 1372 1524 1829 2286 2743 3048 3658 4115
–
* For Screen Sizes of 24 to 300 inches not indicated on the projection tables, use the formulas on the next page.
INSTALLATION
32
Download from Www.Somanuals.com. All Manuals Search And Download.
33
Unit (inch)
Desk top
H (inch) = Width of screen
A = C / cosα
Screen
B = 3.7H / 25.4
C
C (WIDE) = (2.026
ן H) – 2.437 C (TELE) = C (WIDE)
ן 1.3 D = E / 2
Screen center
E = H / 4
ן 3 E
Unit (mm)
A
H (inch) = Width of screen
A = C / cosα
B = 3.7H
C (WIDE) ={(2.026
ן H) – 2.437} ן 25.4 C (TELE) = C (WIDE)
ן 1.3 D = E / 2
D
B
Screen bottom
α
Projector feet
E = H / 4
ן 3 LT100 : 3.8” (97mm)
LT81 : 3.4” (85.6mm)
Ceiling mount
C
LT100 : 3.8” (97mm)
LT81 : 3.4” (85.6mm)
Projector feet
α
B
A : Distance between lens center and
screen center
A
B : Vertical distance between lens center
and screen bottom (screen top for ceil-
ing mount)
Screen top
D
E
C : Horizontal throw distance between
screen surface and projector lens
D : Vertical distance between screen
center and screen bottom (screen top
for ceiling mount)
Screen center
E : Screen Height
INSTALLATION
34
Download from Www.Somanuals.com. All Manuals Search And Download.
35
(A) Top view
Using A Tabletop Or Cart
screen
1. Place your projector on a flat level surface at the optimal distance
from the screen or wall so you realize the size image you want.
(Avoid having bright room lighting or sun light directly on the
screen or wall where you'll be projecting the image.)
2. Connect the power cable, remove the lens cap and turn the projector
on. (If no input signal is available, the projector will display a
background image.)
(B) Side view
3. Ensure that the projector is square to the screen.
4. Move the projector left or right to center the image horizontally on
the screen. (A)
screen
5. [LT100] To center the image vertically (B), lift the front edge of the
projector and press the buttons on the front of the projector, just above
the feet, to release the one-touch tilt feet. (There is approximately 5.0˚
of up and down adjustment for the front of the projector.)
[LT81] To center the image vertically (B), raise the lever-type foot
on the rear straight up.
6. To fine tune the image's position vertically on the screen, rotate each
front foot, and rear feet if necessory.
NOTE: Adjust feet so that lens surface is parallel to the screen.
If you use the projector with the screen tilted, the picture will be
distorted.
Up
Down
7. Adjust the size of the image using the zoom ring lever on the lens.
Up
Down
NOTE: The set up angle of the projector should not exceed 15
degrees, otherwise lamp life could decrease dramatically.
LT100
LT81
+
MEMU
SELECT
STATUS
POWER
ENTER
/OFF
ON
Up
Down
Focus ring
Zoom ring lever
INSTALLATION
36
Download from Www.Somanuals.com. All Manuals Search And Download.
37
3. Put the projector in the large compartment of the case.
Transporting and storing the projector
A padded carrying case has been supplied with your projector. Please
use this case when transporting and storing the projector. The carrying
case also has a compartment for your laptop computer.
To use the carrying case follow the directions below:
R
E
W
S
P O
S T A
T U
[LT81]
/
O F O F
N
+
N
T E R
E
-
E S L E C
T
U
E M
M
1. Remove any accessories.
Projector
4. Zip up the sides of the case.
2. Unfold carrying case.
Zipper
5. Place notebook computer into carrying case.
6. Store remote control and other accessories in front pouch.
* Carry projector carefully. Bumping projector may cause damage.
Note book PC
When restoring the remote
control, place the case on
the functional face to
prevent possible
malfunction.
Other Accessories
INSTALLATION
38
Download from Www.Somanuals.com. All Manuals Search And Download.
39
3. Hold the projector by it’s handle and slide it into the large
compartment of the carrying case.
Transporting and storing the projector
[LT100]
1. Unfold carrying case.
Projector
EUM
SELCT
ACIN
NETR
O
/
AUTS
PWOER
2. Zip up the sides of the case.
4. Zip up the top of the case.
Zipper
5. Unlatch the belt and then place your notebook computer into the
7. Store the remote control and other accessories in the side
pouches on the carrying case.
front pouch.
Note book PC
1
2
Other Accessories
When storing the remote
control, place the remote in
its protective case. The
6. Latch the belt.
2
case will keep the remote
buttons from being acci-
dentally pushed while it is
being stored or trans-
ported. This will keep the
batteries from being dis-
charged.
1
* Carry the projector carefully. Bumping or dropping the projector
may cause damage.
INSTALLATION
40
Download from Www.Somanuals.com. All Manuals Search And Download.
41
WARNING
•
•
•
Only use your projector on a solid, level surface. If the projector falls to the ground, you can be injured and the projector severely damaged.
Do not use the projector where temperatures vary greatly. The projector must be used at temperatures between 41˚F (5˚C) and 95˚F (35˚C).
Do not expose the projector to moisture, dust, or smoke. This will harm the screen image.
•
Ensure that you have adequate ventilation around your projector so
heat can dissipate. Do not cover the vents on the bottom or the side
of the projector.
100"–131"
80"–104"
233"–303"
60"–78"
Ceiling Installation
200"–261"
40"–53"
2.27ft
(691.8mm)
24"–31"
Installing your MultiSync LT81/LT100 Projector on the ceiling must be
done by a qualified technician. Contact your NEC dealer for more
information.
Do not attempt to install the projector yourself.
1.2m (3.94ft)
2.1m (6.89ft)
NOTE : Distances may vary ±5%.
3.15m (10.33t)
4.2m (13.78ft)
5.3m (17.39ft)
10.65m (34.94ft)
12.3m (40.35ft)
If your projector is mounted on the ceiling and your image is upside
down, use the “Menu” and “Select” buttons on your projector cabinet
or (▲) (▼) buttons on your remote control to correct the orientation.
(See page 70.)
Proje c tion d ista nc e a nd sc re e n size e xa m p le s
• Horizontal projection position
• Vertical projection position
Lens centered left to right
Screen size Projection distance L ft.(m) Dimension H inch (cm)
Inches
24
Wide (W)
Tele (T)
Both W & T
2.76” (7.0cm)
4.8” (12.2cm)
6.93” (17.6cm)
9.37” (23.8cm)
11.46” (29.1cm)
3.94ft (1.20m)
6.89ft (2.10m)
10.33ft (3.15m)
40
60
80
100
200
300
5.25 ft (1.60m)
7.87 ft (2.40m)
10.66ft (3.25m) 13.78ft (4.20m)
13.3ft (4.05m) 17.39ft (5.30m)
26.9ft (8.20m) 34.94ft (10.65m) 23.58” (59.9cm)
40.35ft (12.30m) 35.08” (89.1cm)
L
INSTALLATION
42
Download from Www.Somanuals.com. All Manuals Search And Download.
43
Wiring Diagram
INPUT
VIDEO INPUT
(
)
S-VIDEO
RGB INPUT
VIDEO L MONO
-R-
AUDIO
OUTPUT
PC CONTROL
OUTPUT
OUTPUT
REMOTE
CONTROL
AUDIO
RGB
AUDIO
Document Camera
To video, S-video, and audio
inputs on the projector
VCR, Laser Disk Player or DVD Player
DVD Player with Y/Cb/Cr output
To RGB input on the projector
Signal cable (supplied)
To mini D-Sub 15-pin connector on the Projector
Pin adapter for Macintosh
(supplied)
IBM VGA or Compatibles
Macintosh or Compatibles (Desk top type)
Mac ADB adapter
(supplied)
Remote Mouse
Receiver
PS/2 mouse adapter
(supplied)
Remote Mouse
Receiver
Remote Control Guideline
1. Plug the serial cable with the remote mouse receiver into your computer's mouse port and restart your computer to gain remote mouse
control.
2. When using the remote control's built-in infrared mouse on a laptop computer, the laptop's mouse, trackball or trackpad will be disabled.
Disconnect the infrared receiver and restart your computer to regain trackball or trackpad mouse control.
3. If the screen goes blank while using your remote control, it may be the result of the computer's screen-saver or power management
software. If you accidentally hit the OFF button on the remote control, wait one full minute and then press the ON button to resume.
INSTALLATION
44
Download from Www.Somanuals.com. All Manuals Search And Download.
45
Connecting Your PC Or Macintosh Computer
Connecting your PC or Macintosh computer to your MultiSync LT81 (SVGA)/ LT100 (XGA) Projector will enable you to project your
computer's screen image for an impressive presentation. All of these following display standards are supported:
VGA 640
ן 480 for graphics VGA 640
ן 350 for graphics VGA 720
ן 350 for text Macintosh at 640
ן 480 VGA 640
ן 400 for graphics VGA 720
ן 400 for text SuperVGA 800
ן 600 Macintosh at 832
ן 624 XGA1024
ן 768 (AccuBlend) Macintosh at 1024ן 768 (AccuBlend) SXGA1280
ן 1024 (AccuBlend)* * indicates that this resolution is supported by LT100 only.
To connect to a PC, Macintosh or computer equipped with an XGA/SVGA/VGA adapter or compatible graphics adapter, simply:
1. Turn off the power to your projector and computer.
2. If your PC does not support XGA/SVGA/VGA you will need to install an XGA/SVGA/VGA graphics board. Consult your computer's owner's
manual for your XGA/SVGA/VGA configuration. If you need to install a new board, see the manual that comes with your new graphics board for
installation instructions.
3. Use the signal cable that's supplied to connect your PC or Macintosh computer to the projector. For Macintosh, use the supplied pin adapter to
connect to your computer's video port.
4. Turn on the projector and the computer.
5. If the projector goes blank after a period of inactivity, it may be caused by a screen saver installed on the computer you've connected to the projector.
When using a Macintosh with the LT81/LT100, set the DIP switch of the supplied pin adapter according to your resolution. After setting, restart
your Macintosh.
See the following pages for setting of the DIP switch.
• When using with a Macintosh, SVGA (800
ן 600) / XGA (1024ן 768) is recommended if your Macintosh supports this mode. •
When using with a Macintosh PowerBook, output may not be set to 800
ן 600 unless “mirroring” is off on your PowerBook. Refer to owner’s manual supplied with your Macintosh computer for mirroring.
NOTE: A Video Adapter cable manufactured by Apple Computer is needed for a PowerBook which does not have a mini D-Sub 15-pin connector.
Settings for Macintosh adapter
Macintosh models applied
Setting Mode (Fixed resolution)
Setting required to be selected resolution on Mac after
restarting.
Desktop type and PowerBook with 800
ן 600 16” fixed mode (output is 832ן 624) Set to VGA/SVGA (800
ן 600) LCD panel
PowerBook with 640
ן 480 LCD panel 13” fixed mode (output is 640
ן 480) Set to 17” multi-scan mode (640
ן 480) Desktop type with AccuBlend
19” fixed mode (output is 1024
ן 768) Set to 17” multi-scan mode (1024
ן 768) INSTALLATION
46
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Settings for Monitor Mode
Number of DIP switch
S1
S2
S3
S4
S5
S6
S7
S8
Monitor size
ON
ON
ON
ON
ON
15” multi-scan mode /16”–13”
17” multi-scan mode /19”–13”
19” multi-scan mode /21”–13”
13” fixed mode /640
ן 480 VGA/SVGA mode
ON
ON
ON
ON
16” fixed mode /832
ן 624 19” fixed mode /1024
ן 768 ON
NOTE: For setting other than display modes supported by your Macintosh and LT81/LT100, using of the
DIP switch may bounce a image slightly or may display nothing. If this happens, set the DIP switch to the
13” fixed mode and then restart your Macintosh. After that, restore to a displayable mode and then
restart the Macintosh again.
Make sure that LT81/LT100 and your Macintosh are connected with the pin adapter and the supplied
signal cable (mini D-Sub 15-pin connector) and then restart your Macintosh.
Examples of DIP switch setting
VGA/SVGA mode
19” fixed mode
17” multi-scan mode
ON
ON
ON
1
2
3
4 5
6
7
8
1
2
3
4 5
6
7 8
1
2
3 4
5
6
7 8
NOTE: Refer to your computer's owner's manual for more information about your computer's video
output requirements and any special identification or configuring your projector's image and monitor
may require.
INSTALLATION
48
Download from Www.Somanuals.com. All Manuals Search And Download.
49
4. You may be asked to reboot for the changes to take effect, or you' ll
get a message that "Windows is about to resize your display." When
asked if you want to keep your settings, select "Yes."
Changing Video Resolutions
Depending on your computer's graphic capability, you may be able
to select one of several resolutions. Generally a computer- either a
PC or Macintosh- with 1 meg. of memory will run:
640
ן 480 at 16.7 million colors (24 bit Truecolor) 800
ן 600 at 65 thousand colors. Method 2
1. Click on your "My Computer" icon.
2. Open "Control Panel" and select "Display."
3. Change your resolution and click "OK." after the new resolution is
selected.
4. You may be asked to reboot for the changes to take effect, or you' ll
get a message that "Windows is about to resize your display." When
asked if you want to keep your settings, select "Yes."
1024
ן 768 at 256 colors. As the resolution increases, the number of colors you can run de-
creases. With 2 meg. of memory a computer will run:
640
ן 480 at 16.7 million colors (24 bit Truecolor). 800
ן 600 at 16.7 million colors (24 bit Truecolor). 1024
ן 768 at 65 thousand colors. 1280
ן 1024 at 256 colors. Windows 3.1
1. Click on the "Main" icon and open "Control Panel."
2. Select "Change System Settings" and click on "Option."
3. Choose "Change Display Settings."
Windows 95
There are two methods you can use to change your resolution.
4. Select the resolution you want.
5. Choose the current drive or another.
Method 1
1. Move your cursor to the background image and click.
6. Restart Windows for the changes to take effect.
2. In the "Properties" menu, select "Settings."
3. Change your resolution and click "OK."
Macintosh
1. Under the Apple menu, select "Control Panels" and open "Moni-
tors."
2. Click and open "Options."
3. Select your new resolution and click "OK."
If you have an NEC monitor connected to your Macintosh, you may
have a "DPI-On-The-Fly" extension that enables you to change your
resolution directly. The "DPI-On-The-Fly" icon is under your Apple
menu.
INSTALLATION
50
Download from Www.Somanuals.com. All Manuals Search And Download.
51
Connecting Your DVD Player
You can connect your MultiSync LT81/LT100 Projector to a DVD player with the component outputs or Video output. To do so, simply:
1. Turn off the power to your projector and DVD player.
2. If your DVD player has the component video (Y,Cb,Cr) output use the optional 15-pin-to-RCA
ן 3 cable to connect your DVD player to the RGB INPUT connector on the LT81/LT100.
For a DVD player without component video (Y,Cb,Cr) outputs, use common RCA cables (not provided) to connect a composite VIDEO
output of the DVD player to the Video Input of the LT81/LT100.
3. Turn on the projector and the DVD player.
NOTE: Refer to your DVD player's owner's manual for more information about your DVD player's video output requirements.
Connecting Your Document Camera
You can connect your MultiSync LT81/LT100 Projector to a document camera. To do so, simply:
1. Turn off the power to your projector and document camera.
2. Use a standard video cable to connect your document camera to the Video input on your projector.
3. Turn on the projector and the document camera.
NOTE: Refer to your document camera's owner's manual for more information about your camera's video output requirements .
Connecting Your VCR Or Laser Disc Player
Use common RCA cables (not provided) to connect your VCR or laser disc player to your MultiSync LT81/LT100 Projector. To make these
connections, simply:
1. Turn off the power to your projector and VCR or laser disc player.
2. Connect one end of your RCA cable to the video output connector on the back of your VCR, or laser disc player, connect the other end to the
Video input on your projector. Use standard RCA audio patch cords to connect the audio from your VCR, or laser disc player to your projector
(if your VCR, or laser disc player has this capability). Be careful to keep your right and left channel connections correct for stereo sound.
3. Turn on the projector and the VCR, or laser disc player.
NOTE: Refer to your VCR, or laser disc player owner's manual for more information about your equipment's video output requirements.
Connecting An External Monitor
You can connect a separate, external monitor to your projector to simultaneously view on a monitor the image you're projecting. To do so:
1. Turn off the power to your projector and computer, document camera or video source.
2. Use a 15-pin cable to connect your monitor to the RGB OUTPUT connector on your LT81/LT100 projector.
3. Turn on the projector and the computer, document camera or video source.
INSTALLATION
52
Download from Www.Somanuals.com. All Manuals Search And Download.
53
Connecting Your Remote Mouse Receiver
The remote mouse receiver enables you to operate your computer's mouse functions from the NEC MultiSync LT81/
LT100 remote control. It is a great convenience for clicking through your computer-generated presentations.
To connect the remote mouse receiver:
1. Turn off your computer.
2. For PCs: Remove your current mouse and connect the serial cable from the remote mouse receiver to your PC's
mouse port. (Use the 6-pin adapter for connecting to a PS/2 computer.)
For Macintosh: Remove your current mouse from your computer, attach the Macintosh adapter to the remote
mouse receiver's serial cable, and connect the receiver to your mouse port.
3. When the remote mouse receiver is installed, it will disable your regular mouse, disconnect the remote mouse
receiver and restart your computer.
Input for wired remote control (LT100 only)
IBM PC/AT
Input for wired remote control (LT100 only)
Macintosh
IBM PS/2
INSTALLATION
54
Download from Www.Somanuals.com. All Manuals Search And Download.
55
Ⅵ The Remote Mouse Receiver as a mouse for your computer
Serial cable (supplied)
Ⅵ The Remote sensors on the projector cabinet work as the remote sensor
on the Remote Mouse Receiver (LT100 only)
Remote cable
(supplied with LT100 only)
Remote Control
Output
Serial cable
(supplied)
Insert the supplied remote cable here.
Ⅵ You can daisy-chain as many as five projectors and operate them with the same remote control. (LT100 only)
To do so:
1. Turn off your computer.
2. Use the remote control cables supplied to connect the Remote Control Output of one
projector to the Remote Control Input of the next until all the projectors are connected.
Remote cable
(supplied with LT100 only)
INPUT
S-VIDEO
RGB INPUT
OUTPUT
REMOTE
CONTROL
RGB
INSTALLATION
56
Download from Www.Somanuals.com. All Manuals Search And Download.
3 O P E R A T I O N
57
This section describes how to select a computer or video source and how to adjust the
picture and sound.
General Controls Before you turn on your MultiSync LT81/LT100 Projector, ensure
that the computer or video source is turned on and that your lens cap is removed.
1. Turn On The Projector The main power switch is on the back panel of the
MultiSync LT81/LT100 Projector. By turning this switch on, the projector will go
into its standby mode and the power light will glow amber. Only after you press the
"On" button on the remote control or projector cabinet will the power light turn to
green and the projector become ready to use.
NOTE: To turn the projector on and off with just the back panel switch, use the menu
and enable the "auto start" feature. (See page 67. )
2. Select The Computer Or Video Source Press the "Video" (VCR, DVD player,
document camera, or laser disc player), "S-video", "RGB" (computer), or "PC
Card" button on the remote control to display the image. Or press the "Menu"
button on the cabinet and use the icons to select your video source: "Video", "S-
Video", "RGB" or "PC Card".
3. Adjust The Image Size Adjust the size of the screen with the zoom ring lever on the
projector.
4. Focus Adjust the focus with the focus ring on the projector.
5. Turning Off The Projector First press the "off" button on the remote control or press
and hold down the "on/off" button on the cabinet for one second. The power light will
glow amber. Then turn off the main power switch on the back panel. The power light
will go out.
IMPORTANT:
•
The projector should be unplugged if it will not to be used for an extended period.
•
To turn off the image and sound briefly (five minutes or less), use the "Picture Mute"
button on the remote control instead of turning the projector off and on.
•
•
The projector will display a black, blue image or focus pattern if no input signal is
present.
Do not turn the projector off and then immediately back on. The projector needs to
cool for a minute before it can be restarted.
OPERATION
58
Download from Www.Somanuals.com. All Manuals Search And Download.
59
Using The Menus
1. Press the "Menu" button on the remote control or projector cabinet to display the Main Menu.
2. Press the "Select" button on the projector cabinet or (▲) (▼) buttons on your remote control to highlight the menu for the item you want
to adjust.
3. Press the "Enter" button on the projector cabinet or the "Left Click" button on the remote control to select a submenu or item.
4. Adjust the level or turn the selected item "on" or "off" by using the "Adjust" (+) or (–) buttons on the remote control or cabinet. The on-screen
gauge will display your changes. The (+) button is "on" and (–) is "off".
5. The change is stored until you adjust it again.
6. Repeat steps 2-5 to adjust an additional item, or press “Right-Click” on your remote control to quit the menu display.
YCbCr
VIDEO/ S-VIDEO
RGB
NOTE: The following explains conditions that you will encoun-
ter when operating your LT100 while displaying an SXGA
(1280
ן 1024) image. When a menu or message is displayed while an SXGA image is
projected, several lines of information will be lost.
When the "LAMP USAGE 1000 HOURS" message appears, sev-
eral lines of information will be lost.
The "LAMP USAGE 1000 HOURS" message will not appear
when the freeze button is activated.
SXGA images inherently display a 5 to 4 ratio, resulting in an
image that appears to be smaller and more square than the 4 to
3 format commonly displayed.
OPERATION
60
Download from Www.Somanuals.com. All Manuals Search And Download.
61
Menu Descriptions & Functions
Source Menu
Enables you to select a video source such as a VCR, DVD player, laser disk player, compu-
ter or document camera depending on what is connected to your inputs. Press the "Select"
button on the projector cabinet or (▲) (▼) buttons on your remote control to highlight the
menu for the item you want to adjust.
Video
Selects device connected to your video input (VCR, document camera, laser disk player or
DVD player).
S-Video
Selects device connected to S-Video input (Laser disk player, S-VHS VCR or DVD player).
RGB
Selects computer connected to your RGB input. Use the "Adjust" (+) or (–) buttons to
select a standard* or one of five custom settings you can create and store. Press the "Enter"
button on the cabinet or the "Left Click" button on the remote control to save your selection.
NOTE: If a previously saved custom memory location is used with a new or different input signal
it may not sync up, producing a distorted image, or no image at all. If so, follow the instructions
below:
1) Disconnect the signal cable so that there is no input signal. In this condition the on-screen
message will be displayed.
2) Select RGB standard from the source menu.
3) Connect the signal cable again.
NOTE: * Standard is normally used and it can be user changed and automatically recalled.
PC CARD
This feature enables you to make a presentation using the Viewer function with the optional
LT Viewer board (VK-LT81 for LT81 / VK-LT for LT100) installed.
Press the Mouse pad (+) or (-) buttons to select "START" for the image you want to display
first and "SELECT FILE" for the file you want to select or "Select Slide" for the image you
want to slide.
OPERATION
62
Download from Www.Somanuals.com. All Manuals Search And Download.
63
Image Adjustment Menu
Provides access to controls for your image and sound. Use the “Select” button on the projector cabinet or (▲)
(▼) buttons on your remote control to highlight the menu for the item you want to adjust.
The volume, image mode, brightness, contrast, color, tint, sharpness and white balance controls are available for
Video or S-Video sources.
The volume, image mode, brightness, contrast, horizontal position, vertical position, white balance, alignment
and auto picture controls are available for RGB source.
Volume
Use the “Adjust” (+) or (–) buttons to adjust the volume.
Image Mode
Use the "Select" button on the projector cabinet or (▲) (▼) buttons on your remote control to select the item you
want to adjust.
NOTE: Input and Display modes are not available for PC CARD.
Gamma ............. Use the mouse pad (+) or (–) buttons to choose "Normal" when in a lighted room and "Natural
1&2" when in a darkened room. "Natural 1" for better flesh tone; "Natural 2" for true repro-
duction of middle tones.
Input Mode ....... Use the mouse pad (+) or (–) buttons to choose "DOC CAM" for a document camera or other
low APL input, "Standard Video" for a regular video picture such as NTSC, "RGB Signal" for
an RGB source such as a computer, or "Y/Cb/Cr Signal" for a component video source such as
a DVD player.
Display Mode ... Use the mouse pad (+) or (–) buttons to choose "Normal Aspect" for normal video picture with
a 4-to-3 aspect ratio and "Wide Aspect" for DVD's with a 16-to-9 aspect ratio.
NOTE:
1) Flicker may appear on a freeze-frame picture with a Video or S-Video source. If this happens, select the
Document Camera mode using the Image mode icon on the Image Adjustment Menu, and then adjust the
contrast and other items for an optimal image.
2) A frame may freeze for a brief period of time when a video is played back in fast-forward or fast-rewind with
a Video or S-Video source. If this happens, select the Natural mode (for cinema) using the Image Mode icon
on the Image Adjustment Menu.
OPERATION
64
Download from Www.Somanuals.com. All Manuals Search And Download.
65
Brightness
Use the “Adjust” (+) or (–) buttons to adjust the brightness.
Contrast
Use the “Adjust” (+) or (–) buttons to adjust the contrast.
Color*
Use the “Adjust” (+) or (–) buttons to adjust the color.
Tint*
Use the “Adjust” (+) or (–) buttons to adjust the tint.
Sharpness*
Use the “Adjust” (+) or (–) buttons to adjust the sharpness.
White Balance
Use the Mouse pad (+) or (–) buttons to adjust the white balance.
For Video/RGB ... Brightness for each color (RGB) is used to adjust the black level of the screen; Contrast for each
color (RGB) to adjust the white level of the screen.
For Y/Cb/Cr ........ Brightness for each color (Y/Cb/Cr) is used to adjust the white level of the screen; Contrast for
each color (Y/Cb/Cr) to adjust the black level of the screen.
Alignment
Use the Mouse pad (+) or (–) buttons to adjust the horizontal and vertical position, "Picture", and "Fine Picture".
Horizontal
૽૽
Position ........ Use the “Adjust” (+) button to move the image right; (–) to move it left.
Vertical
૽૽
Position ........ Use the “Adjust” (+) button to move the image up; (–) to move it down.
૽૽
Auto Picture
Use the “Adjust” (+) button to turn this feature on so “Picture” and “Fine Picture” adjustments are made automati-
cally. Use the “Adjust” (–) button to turn this feature off so you can make “Picture and Fine Picture” adjustments
manually.
૽૽
Picture Adjustment (when AUTO PICTURE is off)
Use this icon with the “Fine Picture Adjustment” to fine tune the computer image or to remove any vertical banding that might
appear. This function adjusts the clock frequencies to eliminate the vertical banding in the image. Press the “Adjust” (+) and (–)
buttons until the banding disappears. This adjustment may be necessary when you connect your computer for the first time. This
adjustment is made automatically when the Auto Picture is turned on.
RGB AUTO PICTURE ON
RGB AUTO PICTURE OFF
૽૽
Fine Picture (when AUTO PICTURE is off)
Use this icon to adjust the clock phase or to reduce video noise, dot interference or cross talk. (This is evident when
part of your image appears to be shimmering.) Use the “Adjust” (+) and (–) buttons to adjust the image. Use the Fine
Adjustment only after the Picture Adjustment is complete. This adjustment is made automatically when the Auto
Picture is turned on.
NOTE:
ૺ
Color, Tint, and Sharpness controls will not work with an RGB source. The Tint control will not work with a PAL
or SECAM source. The Color and Tint controls will work with a Y/Cb/Cr source.
ૺૺ Alignment controls such as Horizontal and Vertical position controls, and Picture, Fine Picture and Auto Picture
adjustments will not work with a Video or S-Video source.
OPERATION
66
Download from Www.Somanuals.com. All Manuals Search And Download.
67
Power Menu
Provides access to Lamp Usage information, the Auto Start, Power Management and On-
screen Mute features. Use the “Select” button on the projector cabinet or (▲) (▼) buttons on
your remote control to access a submenu. Then press “Adjust” (+) or (–) to choose a specific
option.
Lamp Usage
This tells you how long the lamp has been in operation. It is recommended that you replace a
lamp after 1000 hours of service. After you install a new lamp, select this icon and press and
hold the “Power On” button on the remote control for ten seconds to reset the lamp clock back
to zero.
NOTE: The projector will turn off and go into stand by mode after 1100 hours of service. If this
happens, press the "Power Off" button on the remote control for ten seconds to reset the lamp clock
back to zero. Do this only after replacing the lamp.
Auto Start
Turns the projector on automatically when the main power switch is turned on. This elimi-
nates the need to always use the “Power” button on the remote control or projector cabinet.
Press (+) to turn this feature on and (–) to turn it off.
Power Management
When “Power Off” is on and there is no video input for five minutes or more, the projector
will automatically turn itself off. Press the (+) to turn this feature on and (–) to turn it off.
On Screen Mute
Use the mouse pad (+) button to turn off the On Screen Mute ; (–) to restore it.
The On screen Mute feature keeps the menu from displaying when the projector is turned
on or when switching inputs.
OPERATION
68
Download from Www.Somanuals.com. All Manuals Search And Download.
69
Settings Menu
Enables you to set preferences and other operating options. Use the “Select” button on the projector cabinet or
(▲) (▼) buttons on your remote control to access the submenu you want.
Custom Memory
This enables you to save your current settings for an RGB source in one of five memories, Custom 1-5.
To change the STANDARD settings, proceed as follows:
1. Connect your computer to the MultSync LT81/LT100.
2. Select the "STANDARD" in RGB source.
3. Adjust the horizontal/vertical position, Picture, and Fine Picture adjustments.
4. Select the Custom Memory icon.
5. Press the "Adjust" (+) or (–) buttons to choose a memory location, then press "Enter" on the cabinet or the "Left
Click" on your remote control to save the new settings.
If you do not want to change the STANDARD settings, first selct the Custom Memory icon, then do the same as
step 5.
Capture (with the optional viewer board installed only)
When the Capture is selected, press "Enter" on the projector cabinet or Left Click button on the remote control
to display "Execute" and "capture" an image from a source that is currently being displayed.
When capturing is completed, "Completed" is displayed under the Capture icon.
Unless a flash memory card is inserted into the slot of the viewer board, "No Card" is displayed. This means that
the Capture feature is not available. The "Card Error" display means that the free space of the flash memory card
is insufficient for saving images. Make more space available on the card by erasing unwanted images with your
PC. The number of images that can be captured depends on the size of the flash memory card.
NOTE: Be sure not to turn off the power or remove the flash memory card unless "Completed" is displayed. Doing so
could cause a loss of the data in the flash memory card or damage to the card itself.
Background
Use this feature to display a black, blue screen or focus pattern when no signal is available. Press the mouse pad (+) or (-) buttons to
choose the back screen you want. Press "Enter" on the cabinet or the "Left Click" on your remote control to save your change.
Projection
This reorients your image based upon projector location. Press the “Adjust” (+) or (–) button until it is correct.
Press “Enter” on the cabinet or the “Left Click” on your remote control to save your change. The options are:
front floor projection, rear ceiling projection, rear floor projection, and front ceiling projection.
Language
Use the “Adjust” (+) or (–) to choose one of six languages for on-screen instructions. Press “Enter” on the cabinet or the
“Left Click” on your remote control to save your change. The options are: English, German, French, Italian, Spanish and
Swedish.
Reset
Changes all adjustments to the factory preset levels for each source individually. To activate, you must hold down the “Adjust”
(+) button on the cabinet or remote control for at least two seconds. The adjustments that will be reset are horizontal and vertical
control, picture and fine picture adjustment (for the current source only), brightness, contrast, color, tint, and sharpness.
When custom setting is selected, reset changes all adjustments to the factory preset levels of the current input signal for
selected custom memory location. This will not return to your previous custom setting and will delete your saved settings
from custom memory.
OPERATION
70
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Using the Viewer function
If you use the Viewer function on the projector, you must first install the
optional LT Viewer board (VK-LT or VK-LT81) in the projector and set
up the exclusive software included with the VK-LT or VK-LT81 kit.
See the user's manual included with the Viewer board for installing
and uninstalling the software.
Mounting the Optional LT81 Viewer Board (VK-LT81)
2. Put the board in place and secure it with the four screws supplied
with the VK-LT81 board.
Before mounting the viewer board, you must first switch off the
main power and unplug the power cable.
Connector
To install the Viewer board:
1. Remove the board cover using a flat-head screwdriver.
P O W E R
S T A T U S
/ O F F
O N
+
/ O F F
O N
+
E N T E R
E N T E R
-
-
S E L E C T
S E L E C T
M E M U
M E M U
3. Align the catches of the supplied viewer board cover with the holes.
4. Push down the viewer board cover.
Catch
P O W E R
S T A T U S
P O W E R
O F F
/
O N
S T A T U S
+
E N T E R
/ O F F
O N
+
-
S E L E C T
E N T E R
M E M U
-
S E L E C T
M E M U
OPERATION
72
Download from Www.Somanuals.com. All Manuals Search And Download.
73
Mounting the Optional LT100 Viewer Board (VK-LT)
Before mounting the viewer board, you must first switch off the
main power and unplug the power cable.
To install the VK-LT Viewer board:
1. Turn the projector so that the bottom is up.
2. Remove the screw from the board cover.
3. Put the board in place and secure it with the four screws supplied
with the VK-LT board.
4. Attach the two foot caps to adjust projector height. After complet-
ing, put the projector back in the original position.
OPERATION
74
Download from Www.Somanuals.com. All Manuals Search And Download.
75
Projecting Slides
Orientation of flash memory card and CompactFlash™ (CF™)
memory card insertion.
To Project the Slides (the presentation materials)
1. Insert a flash/CF memory card into the PC card slot.
* To eject the flash memory card, press the Eject button.
The flash memory card has a front and a back side and the flash/CF
memory card is designed to be inserted in only one orientation. The
card is designed so that it cannot be inserted in reverse. Trying to
force the card into slot may result in damage to the card and the card
slot. See the flash/CF memory card manual for information about the
orientation of the flash/CF memory card.
NOTE: Should the card be difficult to insert, do not forcefully
push the card in.
2. Select the PC card as a source.
* Press the Menu button on the remote control or projector cabi-
net and select "PC CARD" from the Source menu.
* If there is no flash/CF memory card in the card slot, the projec-
tor displays a blue back or black back image.
LT100
LT81
3. Select "Select File" or "Select Slide".
* Use the mouse pad (+) or (-) button on the remote control to
select "Select File" or "Select Slide".
* The type of flash/CF memory card required for use in the projector
is a Type II PCMCIA-ATA flash memory card for LT100 and CF
card for LT81. Never use a different type of card, doing so may
result in damage to the card or PC card slot.
4. Select a file or a slide.
NOTE: The mouse pad (+) or (–) button is valid only when the
Use the mouse pad (+) or (–) button on the remote control to
select the file or slide you want to display and press the Enter
button on the cabinet or the Left Click button on the remote con-
trol. See the following pages for more details.
Multi Cursor
Menu button is lit.
Table Cursor
File
File
File
File
2
1
3
4
presentation
presentation
presentation
A
presentation
B
C
D
File
File
File
6
5
7
presentation
presentation
presentation
E
presentation
F
G
H
* The selected file or slide will be displayed.
NOTE: If you select "Start" and press the Enter button on the
cabinet or the Left Click button on the remote control, the slides
will be looped. To use the Start feature, you must first set on the
software included with the LT Viewer board.
CompactFlash and CF are trademarks of SanDisk Corporation.
OPERATION
76
Download from Www.Somanuals.com. All Manuals Search And Download.
77
Selecting a File from a List of Files
3. Use the mouse pad (+) or (–) button on the remote control to
move the Multi-Cursor (blue box) to the file you want to dis-
play a slide from, and press the Enter button on the cabinet or
the Left Click button on the remote control.
* The Viewer feature allows you to store one or more presentation
materials in a single flash/CF memory card. Each material is referred
to as a "file" or "slide".
To select a file from a list of files
1. Press the Menu button on the remote control or cabinet to select
"PC Card".
File
File
File
File
2
1
3
4
Multi Cursor
File
File
File
File
6
5
7
8
2. Use the mouse pad (+) or (-) button on the remote control to se-
lect "Select File" and press the "Enter" button on the cabinet or
the Left Click button on the remote control.
* This will display the first slide of the selected file.
3. Use the mouse pad (+) or (–) button on the remote control to
move the Table-Cursor (yellow box) to the slide you want to
display and press the Enter button on the cabinet or the Left
Click button on the remote control.
NOTE: A maximum of 16 indexes can be switched with "Select
File". The last displayed file, which is always exclusively for use
of Capture, will be displayed during capturing only.
When 17 or more indexes exist in the flash/CF memory card and
you wish to display them, move the index to be displayed to the
beginning of the file indexes with "Editing file indexes" under
"Files" of the software for Viewer.
Table Cursor
presentation
presentation
presentation
presentation
B
A
C
D
Selecting a Slide from a List of Slides (Table)
presentation
presentation
presentation
presentation
F
E
G
H
To select a slide from a list of slides
1. Press the Menu button on the remote control or cabinet to select
"PC Card".
* This will display the selected slide.
2. Use the mouse pad (+) or (-) button on the remote control to select
"Select Slide" and press the "Enter" button on the cabinet or the
Left Click button on the remote control.
NOTE: The Slide (+) and (–) button on the remote control
can be also used to select a file or slide, or to turn pages.
OPERATION
78
Download from Www.Somanuals.com. All Manuals Search And Download.
79
Switching Slides
Capturing the displayed image
To switch slides, press "SLIDE +" or "SLIDE –" button. This will
cancel the Auto Play mode. To set the Auto Play mode, press the Menu
button to select “Start” from the Source menu and press the Enter
button on the cabinet or the Left Click button on the remote control.
This is valid only when the Auto Play mode is selected. See more
information about “Auto Play mode” for the Help file included with the
Viewer board.
The Viewer feature allows you to capture a screen image and store
it to a flash/CF memory card.
To capture a screen image and store it to a flash memory card;
Select "Capture" from the Settings menu and press the Enter button
on the cabinet or Left Click button on the remote control.
* To view the captured image
*
SLIDE– returns to the previous slide.
SLIDE+ advances to the next slide.
NOTE: Editing tasks such as deleting the data inside the flash memory
card cannot be accomplished with the projector. Use the exclusive soft-
ware on your PC for this purpose. If you accidentally delete data re-
quired for playback, playing back the data is not possible.
1. Select "Select File" from the Source menu and display a list
of files.
* A thumbnail (reduced image) of the first captured image
will be displayed.
Effect Sound (LT100 only)
The Viewer function allows you to play back effect sound for the slide.
Playing back effect sound can be accomplished during the switching
slides or files only. To use this feature, you must first specify the effect
sound with the supplied software.
You can adjust volume by using the Volume button.
2. Use the mouse pad (+) button to move the Multi-Cursor (blue
box) to the last file and press the Enter button on the cabinet or
the Left Click button on the remote control.
Display Digital Images
Displaying a picture from the projector is possible if the picture
meets one of the following requirements:
* The picture is stored on an MS-DOS formatted ATA flash
memory card.
File
File
File
File
2
1
3
4
Multi Cursor
* The picture is stored as a compatible format.
File
File
File
File
6
5
7
8
The on-board Viewer searches the PC Card directory for a JPEG or
BMP formatted images.
NOTE:
* Up to 128 images can be recognized as slides for one direc-
tory.
* To use special effects, read images from a flash/CF memory
card and edit them using the supplied software, then store them
to another flash/CF memory card.
* This will display the image you captured first.
NOTE: The menu indicating that capturing is now performing
will be displayed during capturing. During this time do not re-
move the flash/CF memory card nor turn off the power of the
projector. Doing so may destroy the data of the flash/CF memory
card.
* When the flash memory card becomes full, replace it with a new
card.
OPERATION
80
Download from Www.Somanuals.com. All Manuals Search And Download.
4 M A I N T E N A N C E
81
This section describes the simple maintenance procedures you should follow
to replace the lamp and replace the batteries in the remote control.
LT100
LT81
Replacing The Lamp
After your lamp has been operating for 1000 hours or longer, the “sta-
tus” light in the cabinet will turn red. Even though the lamp may still be
working, replace it at 1000 hours to maintain optimal projector perform-
ance.
Step 3
CAUTION
Lamp cover
• DO NOT TOUCH THE LAMP immediately after it has been used. It will
be extremely hot. Allow at least one hour for the lamp to cool before
handling.
• DO NOT REMOVE ANY SCREWS except the lamp cover set screw
and two lamp case screws. You could receive an electric shock.
Step 4
Step 5
• Turn off the main power to the projector and disconnect the power cord.
Allow at least one hour for the lamp to cool.
Lamp housing
• The projector will turn off and go into stand by mode after 1100 hours of
service. If this happens, be sure to replace the lamp. If you continue to
use the lamp after 1000 hours of use, the lamp bulb may shatter, and
pieces of glass may be scattered in the lamp case. Do not touch them as
the pieces of glass may cause injury. If this happens, contact your NEC
dealer for lamp replacement.
Lamp replacement procedure
1. Switch off the main power and unplug the power cord.
2. Turn the main unit so that the bottom is up.
3. Loosen the lamp cover retaining screw.
4. Slide the lamp cover in the direction of the arrow and remove it.
CAUTION: Do not use a lamp other than the NEC replacement lamp.
Order this from your NEC dealer using your projector's model num-
ber.
Step 6
5. Loosen the three retaining screws for the lamp housing.
(There is an interlock on the lamp housing to prevent the risk of electri-
cal shock. Do not attempt to circumvent this interlock.)
6. Holding the handle, pull the lamp housing forward and take it off.
7. Install the new lamp housing and fasten with the three screws.
8. Fasten the three screws for the lamp housing.
Step 7,8
9. Install the lamp cover back in its original position and fasten with the
retaining screw.
10. Reset the lamp time.
Select the lamp usage time menu, then press the ON button on the re-
mote controller and hold it down for at least ten seconds.
NOTE: If resetting the lamp clock back to zero after 1100 hours of
service, press the "Power Off" (not "Power On") button on the remote
control for ten seconds. Do this only after replacing the lamp.
Step 9
MAINTENANCE
82
Download from Www.Somanuals.com. All Manuals Search And Download.
83
Remote Control Battery Installation
1. Press firmly and slide the battery cover off.
2. Remove both old batteries and install new ones (AA). Ensure that you have the batteries' polarity
(+/–) aligned correctly.
3. Slip the cover back over the batteries until it snaps into place.
Operating Range
Range of 360˚ and a distance of 23 feet (7 m) from the remote sensor.
30˚
Operation distance
of 23 feet (7m)
30˚
MAINTENANCE
84
Download from Www.Somanuals.com. All Manuals Search And Download.
85
Cette section décrit les procédures simples d’entretien que vous aurez à
suivre pour remplacer la lampe et remplacer les piles de la télécommande.
LT100
LT81
Remplacement de la lampe
Lorsque la lampe a été utilisée pendant 1000 heures ou plus, le voyant “Status” (état) du
coffret s’allume. Même si la lampe peut encore fonctionner, remplacez-la au bout de
1000 heures pour conserver une performance optimale de votre projecteur.
Etape 3
Etape 4
PRECAUTIO N
Couvercle de
la lampe
•
NE TOUCHEZ PASA LA LAMPE juste après qu’elle a été utilisée. Elle est très
chaude. Laissez-la refoidir pendant au moins une heure avant de la manipuler.
• NE RETIREZAUCUNEVIS mis à part la vis qui fixe le couvercle de lampe
et les deux vis du compartiment de lampe. Vous risquez de recevoir une
décharge éléctrique.
• Mettez le projecteur hors circuit et débranchez le cordon d’alimentation.
Laissez refroidir la lampe pendant au moins une heure.
• Le projecteur s’éteindra et restera en attente après 1100 heures d’utilisation.
Dans ce cas, remplacez la lampe. Si vous continuez d’utiliser la lampe après
1000 heures d’utilisation, l’ampoule peut se briser et des brisures de verre
peuvent être éparpillées dans le compartiment de la lampe. Ne les touchez pas
car elles peuvent vous blesser. Dans ce cas, contactez votre revendeur NEC
afin de procéder au remplacement de la lampe.
Boîtier de
lampe
Etape 5
Pour remplacer la lampe :
1. Mettre l'appareil sous tension et débrancher le cordon d'alimentation.
2. Retourner l'unité principale pour avoir accès à la partie inférieure.
3. Desserrer le vis de fixation du couvercle de la lampe.
4. Faire glisser le couvercle de la lampe dans la direction de la flèche et le déposer.
ATTENTION : ne pas utiliser une autre lampe que la lampe de remplacement NEC.
Etape 6
Commander celle-ci auprès du détaillant NEC à l'aide du numéro de modèle du projecteur.
5. Desserrer les trois vis du boîtier de lampe.
(Il y a un mécanisme de déclenchement dans le boîtier de lampe pour empêcher
une décharge électrique. Ne pas essayer de circonvenir ce mécanisme)
6. En maintenant la poignée, tirer le boîtier de lampe vers l'avant et l'extraire.
7. Installer le nouveau boîtier de lampe et le fixer avec les trois vis.
8. Serrer les trois vis du boîtier de lampe.
Etape 7,8
9. Réinstaller le couvercle de la lampe dans sa position d'origine et le fixer avec les vis de
fixation.
10. Initialiser le temps de la lampe.
Sélectionner le menu de temps d'utilisation de la lampe, puis appuyer sur la touche ON
sur la télécommande et la maintenir enfoncée pendant au moins dix secondes.
REMARQUE : Pour remettre à zéro l’horloge de lampe après 1100 heures d’utilisation, appuyez sur la
touche “Power Off” (alimentation désactivée)(et non “Power On” (alimentation activée)) de la télécommande
pendant dix secondes. Effectuez cette opération uniquement lorsque vous avez remplacé la lampe.
Etape 9
MAINTENANCE
86
Download from Www.Somanuals.com. All Manuals Search And Download.
87
Installation des piles de la télécommande
1. Appuyez fermement et retirez le couvercle des piles en le faisant glisser.
2. Retirez les deux piles usagées et installez de nouvelles piles (AA). Assurez-vous de respecter la
polarité (+/–) des piles.
3. Remettez le couvercle des piles en le faisant glisser, jusqu’à ce qu’il s’emboîte.
Portée de fonctionnement
Portée de 360 degrés et d'une distance de 7 mètres du capteur le télécommande.
30˚
Operation distance of 7m
30˚
MAINTENANCE
88
Download from Www.Somanuals.com. All Manuals Search And Download.
5 T R O U B L E S H O O T I N G
89
This section helps you resolve problems you may encounter while setting up or using your MultiSync LT81/LT100 Projector.
Status Light Messages
Condition
Status
OFF
Ⅵ Normal
On Continually
Ⅵ The projector lamp has exceeded 1000 hours of operation and should be replaced.
Blinking very rapidly
Ⅵ The lamp housing is not correctly installed. Install it correctly.
(On and off in a cycle of 1 sec.)
Blinking rapidly
(On and off in a cycle of 4 sec.)
•
•
The temperature protector has been triggered. If the room temperature is high, move the projector
to a cooler location. If the temperature inside the projector is high, check the cooling fan ventila-
tion hole and the ventilation hole on the bottom of the projector. If any of the holes are blocked,
remove whatever is blocking them.
The temperature protector has been triggered. If you switch the main Power switch Off, then
immediately switch it On again, sometimes the power does not come on. If this happens, wait one
minute, then switch the power On again.
Blinking Slowly
Ⅵ The cooling fan has stopped. Contact your NEC dealer for service.
(On and off in a cycle of 8 sec.)
Blinking very slowly
Ⅵ The lamp is not turned on.
(On and off in a cycle of 12 sec.)
• The projector was turned off and back on too quickly. Turn off the projector, wait one
minute, then turn the projector back on. Or the lamp is burnt out.
TROUBLE SHOOTING
90
Download from Www.Somanuals.com. All Manuals Search And Download.
91
Common Problems & Solutions
Problem
Check These Items
Does not turn on
• Check that the power cable is plugged in and that the power switch on the back panel is on.
• Ensure that the lamp cover and lamp housing are installed correctly. (See page 81.)
• Check the status light to see if the projector has overheated or the lamp usage exceeds 1100
hours.
No picture
•
Use the menu icons to select your source (Video, S-Video, RGB or PC Card). (See pages 61 and 62.)
• Ensure your cables are connected properly.
• Use icons to adjust the brightness and contrast.
• Remove the lens cap.
• Is the POWER indicator blinking?
• Reset the settings or adjustments to factory preset levels using the RESET icon on the Settings
Menu.
Image isn’t square
to the screen
• Reposition the projector to improve its angle to the screen.
• Adjust the focus. (See page 36.)
Picture is blurred
• Reposition the projector to improve its angle to the screen.
• Ensure that the distance between the projector and screen is within the adjustment range of the lens.
Problem
Check These Items
Image is scrolling
vertically, horizontally
or both
• Use icons to select the source you want to input.
• If PC signal is set up in Custom Setting, select corresponding Custom Setting (Custom 1,
Custom 2, etc.).
• Install new batteries. (See page 83.)
• Make sure there are no obstacles between you and the projector.
• Stand within 23 feet (7m) of the projector.
Remote control does
not work
See the Status Light message chart on pages 89 and 90.
Status indicator is lit or
blinking
If “Auto Picture” is off, turn it on. If “Auto Picture” is on, turn it off and balance the image with the
Picture Adjustment icon and Fine Picture Adjustment icon.
Cross color in RGB
mode
To Contact Your NEC Service Representative, Call 1-800-836-0655
TROUBLE SHOOTING
92
Download from Www.Somanuals.com. All Manuals Search And Download.
6 S P E C I F I C A T I O N S
93
This section provides technical information about the MultiSync LT81/LT100 Projector's performance.
Optical
DMDTM
Lens
Single Chip Digital Micromirror Device(DMDTM), 800
ן 600 dots (LT81) / 1024ן 768 dots (LT100) Manual zoom, manual focus
F 2.44 f =26-30 mm
Lamp
Metal halide lamp 280 W
610-7620 mm (24-300 inches) diagonal
1.2 – 12.3m
Image Size
Projection Distance
Electrical
Inputs
Video (NTSC / PAL / SECAM / NTSC 4.43)
RGB LT81: (H : 15 – 60 kHz, V : 50 – 85 Hz)
LT100: (H : 15 – 85 kHz, V : 50 – 85 Hz)
RGB: 60 MHz
Video Bandwidth
Color Reproduction
Horizontal Resolution
Full color, 16.7 million colors simultaneously.
NTSC /YCbCr 550 (LT81 : 500), PAL 350, SECAM 350, NTSC4.43 350 TV lines
RGB LT81: 800 dots horizontal, 600 dots vertical
LT100: 1024 dots horizontal, 768 dots vertical
Power Requirement
Input Current
100 – 120 / 220 – 240 VAC, 50 / 60 Hz
4.6 A (100 – 120 VAC) / 2.2 A (220 – 240 VAC)
Mechanical
Dimensions (LT81)
9.7" (W)
ן 5.1" (H)ן 12.8" (D) / 246 mm (W)ן 130 mm (H)ן 325 mm (D) (Including lens hood and feet) 9.7" (W)
ן 5.1" (H)ן 12.7" (D) / 246 mm (W)ן 130 mm (H)ן 310 mm (D) (Not including lens hood) Dimensions (LT100)
Net Weight
9.8" (W)
ן 5.6" (H)ן 13.4" (D) / 250 mm (W)ן 142 mm (H)ן 340 mm (D) (Including lens hood and feet) 9.8" (W)
ן 5.6" (H)ן 12.6" (D) / 250 mm (W)ן 142 mm (H)ן 320 mm (D) (Not including lens hood) LT81: 9.9 lbs / 4.5 kg
LT100: 10.8 lbs / 4.9 kg
Operational Temperatures
Projector: 41° – 95°F (5°to 35°C), 30 – 85% humidity
Remote control: 32° – 140°F (0° to 60°C)
Remote mouse receiver: 32° – 140°F (0° to 60°C)
Regulations
UL Approved (UL 1950, CSA 950)
Meets DOC Canada requirements
Meets FCC Class A requirements
Digital Light Proccessing, DLP, Digital Micromirror
Device and DMD are trademarks of Texas Instruments.
SPECIFICATIONS
94
Download from Www.Somanuals.com. All Manuals Search And Download.
95
Cabinet Dimensions (LT81)
12.2"
(310)
0.6"
(15)
5.1"
(129.6)
3.9"
(98)
0.7"
(17)
0.4"
(11)
Lens Center
0.9"
3.4"
(23)
(85.6)
MAX
Lens Center
Unit : inch (mm)
SPECIFICATIONS
96
Download from Www.Somanuals.com. All Manuals Search And Download.
97
Cabinet Dimensions (LT100)
MAX
0.79"
(20)
12.6"
(320)
5.6"
(142)
4.5"
(114)
0.53"
(13.5)
Lens Center
Lens Center
Unit : inch (mm)
SPECIFICATIONS
98
Download from Www.Somanuals.com. All Manuals Search And Download.
99
D-Sub Pin Assignments
PC 15-Pin mini D-Sub
Pin No. Signal to be connected
PC 15-Pin mini D-Sub
1
Red
2
4
3
1
5
9
6
10
8
7
2
3
Green
Blue
15 14 13 12
11
4
GND
5
GND
6
7
8
9
10
11
12
13
14
15
Red GND
Green GND
Blue GND
No Connection
Digital GND
GND
No Connection
Horizontal Sync
Vertical Sync
No Connection
SPECIFICATIONS
100
Download from Www.Somanuals.com. All Manuals Search And Download.
101
Timing Chart
Y/N
Signal
Resolution
Refresh
Rate (Hz)
F.H.
(kHz)
Dot
Clk(MHz)
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
Y
NTSC
PAL
640
ן 480 768
ן 576 768
ן 576 640
ן 350 640
ן 400 640
ן 400 640
ן 400 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 640
ן 480 720
ן 350 720
ן 400 720
ן 400 720
ן 350 60
15.734
15.625
15.625
37.86
31.47
37.86
35
-
50
-
SECAM
VESA
IBM
50
-
85.08
70
31.5
25.175
31.5
30.24
25.175
25.175
25.175
31.334
30.24
31.5
31.5
31.49
36
VESA
MAC
VESA
IBM
85.08
66
59.94
60
31.47
31.47
31.47
34.97
35
MAC
MAC
MAC
VESA
VESA
IBM
60
66.7
66.67
72.81
75
37.86
37.5
75
39.375
43.269
31.469
31.4469
37.927
39.44
VESA
IBM
85.01
70.09
70.09
85.04
87.85
28.322
28.322
40
IBM
VESA
IBM
35.5
Y
Y
Y
Y
Y
Y
Y
N
Y
Y
Y
Y
Y
#
IBM
720
ן 400 87.7
39.375
35.16
35.5
36
VESA
VESA
VESA
VESA
VESA
MAC
VESA
VESA
VESA
IBM
800
ן 600 56.25
60.32
72.19
75
800
ן 600 800
ן 600 37.879
48.077
46.88
40
50
800
ן 600 49.5
56.25
57.283
44.9
65
800
ן 600 85.06
74.55
43interlace
60
70.07
72.03
74.93
75.03
85
53.674
49.725
35.5
832
ן 624 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1024
ן 768 1152
ן 870 1152
ן 900 1152
ן 900 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 1280
ן 1024 48.363
57.476
58.131
60.241
60.023
68.677
49.7
75
1024
ן 768 and 832ן 624 images are com- pressed into 800
ן 600 on LT81. 79
MAC
VESA
VESA
SGI
MAC
SUN
80
78.75
94.5
70
Y
#
60.4
75.6
# 1152
ן 870, # 1152ן 900 and # 1280ן 1024 images are compressed into 1024
ן 768 on LT100.
68.7
100
92.94
105.6
107.35
108
118.5
135
135
135
#
65.95
70.05
60
61.769
71.736
63.9
#
SGI
#
SGI
#
VESA
MAC
HP
60.02
69.89
72.01
75.03
76.11
64.286
74.882
78.125
79.976
81.13
#
#
NOTE: Images marked with a # are not supported
by LT81.
#
VESA
SUN
#
SPECIFICATIONS
102
Download from Www.Somanuals.com. All Manuals Search And Download.
103
PC Control Command Reference
Command Codes
No. Function
Code Data Description
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
Video
03H No
04H No
C6H No
27H No
08H No
14H No
47H No
45H No
11H No
43H No
DEH No
DFH No
DCH No
DDH No
21H No
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
RGB
S-Video
PC CARD
Power On
Power Off
Picture Mute
Audio Mute
Onscreen Mute
Reset
(available only when Viewer kit is connected to)
D Up
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
D Down
D Right
D Left
D Right Up
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
D Left Up
22H No
23H No
24H No
4CH No
4BH No
20H No
33H No
34H No
35H No
36H No
19H No
1AH No
1BH No
1CH No
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
Same as remote
D Right Down
D Left Down
Freeze
Slide +
(available only when PC CARD is selected)
(available only when PC CARD is selected)
Slide –
Front Floor
Front Ceiling
Rear Floor
Rear Ceiling
Auto Start On
Auto Start Off
Auto Picture On
Auto Picture Off
Input Mode Select 1DH Yes
0
1
0
1
2
Standard VIDEO (available only when VIDEO/S-VIDEO is selected)
Doc Camera
Normal
31
Gamma Select 1EH Yes
Natural 1
Natural 2
SPECIFICATIONS
104
Download from Www.Somanuals.com. All Manuals Search And Download.
105
Command Codes (continued)
No. Function
Code Data Description
32
Display Mode Select 1FH Yes
0
1
Normal Aspect
Wide Aspect
33
34
35
36
37
38
39
40
41
42
43
44
45
46
Power Management On 15H No
Power Management Off 16H No
Digital Zoom W
Digital Zoom T
Brightness
Contrast
89H No
8AH No
60H Yes
62H Yes
64H Yes
66H Yes
68H Yes
6AH Yes
70H Yes
6EH Yes
Same as remote
Same as remote
0 (00H) –– 63 (3FH)
0 (00H) –– 63 (3FH)
0 (00H) –– 63 (3FH)
-32 (E0H) –– 31 (1FH)
0 (00H) –– 63 (3FH)
0 (00H) –– 63 (3FH)
-32 (FFE0H)–– 31 (001FH)
0 (00H) –– 127 (7FH)
Color
Tint
Sharpness
Audio Volume
Picture Adj
Fine Picture
H Position
V Position
72H Yes -128 (80H) –– 127 (7FH)
74H Yes
-64 (C0H) –– 63 (3FH)
47
48
Lamp Reset
3FH No
3DH Yes
Lamguage Select
0
1
2
3
4
5
6
English
German
French
Italian
Spanish
Swedish
Japanese
WHITE BALANCE
49
50
51
52
53
54
Sub Brightness R
Sub Brightness G
Sub Brightness B
Sub Contrast R
Sub Contrast G
Sub Contrast B
75H Yes 0 (00H) –– 63 (3FH)
76H Yes 0 (00H) –– 63 (3FH)
77H Yes 0 (00H) –– 63 (3FH)
78H Yes 0 (00H) –– 63 (3FH)
79H Yes 0 (00H) –– 63 (3FH)
7AH Yes 0 (00H) –– 63 (3FH)
SPECIFICATIONS
106
Download from Www.Somanuals.com. All Manuals Search And Download.
107
Cable Connection
Communication Protocol
Baud rate:
Data length:
Parity:
9600 bps
8 bits
No parity
One bit
None
Stop bit:
X on/off:
Full duplex
Communications
procedure:
If the CPU of the projector has received the data correctly, it returns an ACK(C5H). If the received data is not correct, the CPU returns a
NAK(CAH), then the following status:
Receiving success:
Receiving failure:
Err 01:
C5
CA Err
Command Error (command not supported)
Checksum Error
Err 02:
Err 03:
Busy (command not acceptable)
Err 04:
Parameter Error ( parameter data abnormal)
PC Control Connector (DIN-8P)
To RxD of PC
ᮣ
NOTE: If failing in powering-on, the CPU returns the following NAKs:
44
8
6
7
CA Err 1
Err 1 8X (Apply the corresponding bit.)
Bit 0: Lamp housing is not attached correctly
Bit 1: Fan stoppage
5
4
3
2
1
Bit 2: Overheated
Bit 3: Lamp lighting failure
To GND of PC
To TxD of PC
ᮣ
ᮤ
SPECIFICATIONS
108
Download from Www.Somanuals.com. All Manuals Search And Download.
|