Versa E6000
Disassembly Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Overview
This document contains step-by-steps disassembly instructions for the Versa E6000/EasyNote G5 chassis. The
instructions are illustrated where necessary with images of the part that is being removed or disassembled.
Furthermore, the screws that are removed are shown next to the image of the parts themselves.
NEC reserves the right to make changes to the Versa E6000/EasyNote G5 chassis without notice.
Technician Notes
Only technicians authorized by NEC Computers International BV should attempt to repair this equipment. All
troubleshooting and repair procedures are detailed to allow only subassembly/module level repair. Because of the
complexity of the individual boards and subassemblies, no one should attempt to make repairs at the component
level or to make modifications to any printed wiring board. Improper repairs can create a safety hazard. Any
indication of component replacement or printed wiring board modifications may void any warranty or exchange
allowances.
Disassembly Instructions
When disassembling the system unit, follow these general rules:
„
„
„
Do not disassemble the system into parts that are smaller than those specified in the instructions.
Label all removed connectors. Note where the connector goes and in what position it was installed.
Turn off the power and disconnect all power and all options.
Reassembly Instructions
Reassembly is the reverse of the disassembly process. Use care to ensure that all cables and screws are returned
to their proper positions. Check that no tools or any loose parts have been left inside the chassis. Check that
everything are properly installed and tightened.
Required Tools
All disassembly procedures can be perform using the following tools:
„
„
„
„
„
„
„
„
PH 0x60 Philips screwdriver
PH 0x40 Philips screwdriver
4.0 x 60 Flat screwdriver
2.0 x 30 Flat screwdriver
SW5.0 Spacer screwdriver
SW4.5 Spacer screwdriver
Small tweezers
Pin
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING
Ensure that the computer is disconnected from
its power source and from all
telecommunications links, networks, or modem
lines whenever the chassis cover is removed.
Do not operate the computer with the cover
removed.
Hazardous Voltage
There is hazardous voltage present inside the computer
when it is connect to an AC supply, even when the
computer’s power switch is off. Exposure to hazardous
voltage could cause personal injury. To avoid risk of injury,
contact an Authorized Service Provider for proper
(UN)installation of optional hardware devices.
AVERTISSEMENT
Assurez-vous que le système est débranché de
son alimentation ainsi que de toutes les
liaisons de télécommunication, des réseaux, et
des lignes de modem avant d’enlever le capot.
Ne pas utiliser le système quand le capot est
enlevé.
Avoid Electrostatic Discharge
Electrostatic electricity can easily damage circuit cards and
integrated circuits (ICs). To reduce risk of damage, store
them in protective packaging whenever they are not
installed in your system.
WARNUNG
Das System darf weder an eine Stromquelle
angeschlossen sein noch eine Verbindung mit
einer Telekommunikationseinrichtung, einem
Netzwerk oder einer Modem-Leitung haben,
wenn die Gehäuseabdeckung entfernt wird.
Nehmen Sie das System nicht ohne die
Abdeckung in Betrieb.
Add-in cards can be extremely sensitive to ESD and always
require careful handling. After removing the card from the
computer, place the card flat on a grounded, static-free
surface, component-side up. Use a conductive foam pad if
available, but not the card wrapper. Do not slide the card
over any surface.
Before you install or remove memory modules, video
memory, disk drives, circuit cards or other devices, protect
them from static electricity. To do so, make sure your
computer’s power switch is OFF. Then, unplug the
computer’s AC power cord. Before picking up the device you
(un)install, you should wear an anti-static wrist wrap
(available at electronic supply stores). Be sure to connect
the wrist wrap to an unpainted metal portion of the computer
chassis. As an alternative, you can dissipate electrostatic
build-up by touching an unpainted metal portion of the
computer chassis with one hand. Then touch the device you
are (un)installing with the other hand, and maintain
continuous contact with it until it is (un)installed in the
computer.
ADVERTENCIA
Asegúrese de que cada vez que se quite la
cubierta del chasis, el sistema haya sido
desconectado de la red de alimentación y de
todos lo enlaces de telecomunicaciones, de red
y de líneas de módem. No ponga en
funcionamiento el sistema mientras la cubierta
esté quitada.
WAARSCHUWING
Zorg er voor dat alle verbindingen van en naar
de computer (stroom, modem netwerk, etc)
verbroken worden voordat de behuizing
geopend wordt. Zet de computer nooit aan als
de behuizing geopend is.
AVVERTENZA
Prima di rimuovere il coperchio del telaio,
assicurarsi che il sistema sia scollegato
dall’alimentazione, da tutti i collegamenti di
comunicazione, reti o linee di modem. Non
avviare il sistema senza aver prima messo a
posto il coperchio
Power Supply Unit
Under no circumstances should you attempt to disassemble
the power supply. The power supply contains no user-
serviceable parts. Inside the power supply are hazardous
voltages that can cause serious personal injury. Always
return a defective power supply to your dealer.
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Battery
Perform the following steps to remove the battery:
1. Make sure to power off the Versa E6000/EasyNote G5.
2. Turn the unit upside down.
3. Unlock the battery and slide it out of its place as the arrow shows in Fig. 1
Fig. 1 Removing the battery
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Memory Module
To remove the Memory Module, first remove the battery (see Removing the Battery), then
perform the following steps:
1. Release the one screw retaining the memory module cover.
M2.5x5 Silver
Fig. 2 Removing the screw retaining the memory module slot cover
2. Unclip the memory module as shown in Fig. 3
Fig. 3 Removing the memory module
3. Remove the memory module from its slot and put it aside.
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the MDC Modem
To remove the MDC Modem, first remove the Memory Module Cover (see Removing Memory
Module) then perform the following steps:
1. Release screws and disconnect cable on MCD Modem as shown in Fig. 4
M2.5x4 Silver
Fig. 4 MDC Modem
2. Lift up the MDC modem and put it aside.
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Hard Disk Drive
To remove the hard disk drive, first remove the battery (see Removing the Battery), then
perform the following steps:
1. Remove the screws as shown in Fig. 5
M2.5x4 Copper
Fig. 5 Removing the Hard disk drive cover
2. Release the screws that secure HDD module as shown in Fig. 6 and carefully pull the
HDD module out from the base unit.
M3x8.5 Silver
Fig. 6 Screw retaining the HDD module
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Keyboard
To remove the Keyboard, first remove the battery (see Removing the Battery), then perform
the following steps:
1. Release the keyboard cover from the rear of the system as shown in Fig. 7
Fig. 7 Releasing the keyboard cover
2. Lift up the keyboard cover carefully and disconnect cable attached on it as shown in Fig. 8
Fig. 8 Lifting up the Keyboard Cover
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Lift up the keyboard and disconnect it from the system as shown in Fig. 9
M2.5x9 Silver
Fig. 9 Disconnecting the keyboard flat cable
Removing the Optical Disk Drive
To remove the ODD, first remove the battery (see Removing the Battery) and remove the
Keyboard (see Removing the Keyboard) then perform the following steps:
1. Remove the screws retaining the optical drive as shown in Fig. 10
M2.5x9 Silver
Fig. 10 Releasing the optical drive
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Flip over the unit, and push the ODD module out from the base unit as shown in Fig. 11
Fig. 11 Pushing the optical drive out from the base unit
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the LCD Module
To remove the LCD Module first remove the battery (see Removing the Battery) and remove
the Keyboard (see Removing the Keyboard) then perform the following steps:
3. Remove the screws retaining the Heat Plate as shown in Fig. 12
M2.5 x 5 Silver
Fig. 12 Removing the screws retaining the Heat Plate
4. Flip over the base unit and release the screws retaining the LCD Module.
M2.5x9 Silver
Fig. 13 Removing the screws retaining the LCD Module
5. Release the screws on the system rear side as shown in Fig. 14
M2.5x9 Silver
Fig. 14 Removing the screws retaining the LCD Module
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
6. Open up the LCD lid, release the screws and the LCD cable connector.
M2x4 Silver
Fig. 15 Removing screws retaining LCD Cable Connector
7. Carefully lift up the LCD Module.
Removing the WLAN Card Module
To remove the WLAN Card Module first remove the battery (see Removing the Battery),
remove the Keyboard (see Removing the Keyboard) and removing heat plate (see Removing
the LCD Module) then perform the following steps:
1. Remove the wireless antenna connector and release the WLAN Card Module as shown in
Error! Reference source not found.
Fig. 16 Wireless Card Module
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the LCD Panel
To remove the LCD panel, first remove the LCD module (see Removing the LCD Module),
then perform the following steps:
1. Use a pin to remove the rubber cover on the LCD module as shown in Fig. 17
2. Remove all screws as shown in Fig. 17 and remove carefully the LCD cover.
M2.5x7 Silver
Fig. 17 Removing the rubber covers & screws on the LCD Module
3. Release the inverter board by remove the screw and disconnect all connectors as shown
in Fig. 18
M2x4 Silver
Fig. 18 Removing the Inverter Board
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Carefully lift up the LCD panel.
5. Remove the screws at both sides of the LCD panel in order to release the LCD hinges as
shown in Fig. 19
M2x4 Silver
Fig. 19 Removing the LCD Panel hinges
Removing the CPU
To remove the CPU first remove the battery (see Removing the Battery) and remove the
Keyboard (see Removing the Keyboard) then perform the following steps:
1. Remove the screws retaining the Heat Plate as shown in Fig. 20
M2.5 x 5 Silver
Fig. 20 Removing the screws retaining Heat Plate
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Remove the CPU Fan screws, disconnect the CPU Fan connector and remove the CPU
Fan.
M2.5x6.5 Silver
Fig. 21 CPU Fan
3. Unscrew screws on CPU Heat Sink in descending order (3Æ2Æ1) as shown in Fig. 22
M2.5x4 Copper
Fig. 22 CPU Heat Sink
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: Beware of screws use on the CPU heat sink! Make sure to use the screw size M2.5x4, otherwise it
might cause damage to the CPU die. When install heat sink, screws must be secured in ascending order
(1Æ2Æ3).
4. Unlock the CPU from the CPU socket and lift up the CPU carefully.
Fig. 23 Unlocking the CPU
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Top Cover
To remove the Top Cover , first remove the battery (see Removing the Battery), remove the
HDD (see Removing the Hard Disk Drive), remove the Optical Disk Drive (see Removing the
Optical Disk Drive), remove the Keyboard (see Removing the Keyboard) and remove the LCD
Module (see Removing the LCD Module) then perform the following steps:
1. Remove all screws on the bottom of the base unit as shown in Fig. 24
M2.5x9 Silver
Fig. 24 Bottom Cover
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Release all screws on the top cover as shown in Fig. 25
A = M2.5x5 Silver
B=M2.5x6 Silver
Fig. 25 Top Cover screws
3. Disconnect the Touch Pad Connector as shown in Fig. 26
Fig. 26 Touch Pad connection
4. Carefully lift up the Top Cover.
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Touch Pad
To remove the touch pad, first remove the top cover (see Removing the Top Cover), then
perform the following steps:
1. Unscrew the screws on the Top Cover as shown in Fig. 27
M2x4 Silver
Fig. 27 Touch Pad
2. Carefully separate the Touch Pad module from Top cover.
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Main Board
To remove the Main Board, first remove the Top Cover (see Removing Top Cover) then
perform the following steps:
1. Remove the Hex screws from the VGA Port as shown in Fig. 28
M2.5x10 Silver
Fig. 28 VGA Port
2. Unscrew those screws on HDD holder as shown in Fig. 29 and separate it carefully from
Main Board.
A = M2.5x5 Silver
B = M2x8 Silver
Fig. 29 HDD Holder
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Disconnect Audio board from main board as shown in
Fig. 30 Lifting up the audio board
4. Disconnect Speaker and Lid switch connectors from the Main board as shown in Fig. 31
Fig. 31 Connectors on Main Board
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Unscrew the screws encircled in Fig. 32
A = M2.5x8
B = M2.5x5 Silver
Fig. 32 Screws on Main Board
6. Lift up the Main Board as shown in Fig. 33
Fig. 33 Lifting up the Main Board
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Removing the Speaker Assembly
To remove the Speaker Assembly, first remove the Main Board (see Removing the Main
Board) then perform the following steps:
1. Remove the screws holding Speaker Assembly as shown in Fig. 34
M2x7 Silver
Fig. 34 Speaker Assembly
2. Carefully remove the Speaker assembly from Bottom Cover and place it aside.
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
DIP Switch Settings
2
1
5
6
9
10
Jumper
Status
Open
Open
Open
NEC
Open
Open
Close
NEC
Close
Open
Close
Open
Close
1-2
3-4
5-6
Close
Close
NEC
Close
NEC
Open
PB
Logo
Setting
JP consumer JP Commercial
APAC
HK/CN
EU
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Screws
M3x8 Silver
M2.5x6.5 Silver
M2.5x9 Silver
M2.5x7 Silver
M2.5x5 Silver
M2.5x10 Silver
M2x7 Silver
M2x4 Silver
M2.5x8 Silver
M2.5x6 Silver
M2x8 Silver
M2.5x4 Copper
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Notice
The information in this guide is subject to change without notice.
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in
any form or by any means without prior written consent from NEC Computers International BV.
NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS
OR OMISSIONS CONTAINED HEREIN; NOR FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING
FROM THE FURNISHING, PERFORMANCE, OR USE OF THIS MATERIAL.
Copyright © 2004 NEC Computers International BV. All rights reserved.
NEC is a trademark of NEC Computers International BV.
The names of actual companies and products mentioned herein may be trademarks and/or registered trademarks
of their respective owners.
Versa E6000/EasyNote G5 Disassembly Manual
Author: Allen Koay
First Edition: March 2004
Document Part Number:
Version: 1.1
NECCM
A division of NEC Computers International BV
NEC Versa E6000/PB Easy Note G5 Disassembly Manual
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
|