User’s Manual
MultiSync V322
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARATION OF CONFORMITY
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party: NEC Display Solutions of America, Inc.
Address:
500 Park Boulevard, Suite 1100
Itasca, Illinois 60143
(630) 467-3000
Tel. No.:
Type of Product:
Display Monitor
Equipment Classification: Class B Peripheral
Model:
MultiSync V322 (V322)
We hereby declare that the equipment speciÞed above
conforms to the technical standards as speciÞed in the FCC Rules.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync V322 (V322) colour monitor so as not to interfere with radio and
television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use the supplied shielded video signal cable, Mini D-SUB 15 pin to Mini D-SUB 15 pin.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
Windows is a registered trademark of Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and
Switzerland.
DisplayPort and DisplayPort Compliance Logo are trademarks owned by the Video Electronics Standards
Association.
All other brands and product names are trademarks or registered trademarks of their respective owners.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC
in the United States and other countries.
English-1
Download from Www.Somanuals.com. All Manuals Search And Download.
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS THE
PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE POWER
CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS
INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit has
been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this monitor in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
European
Continental
Plug Type
North America
U.K.
Chinese
Japanese
Plug Shape
U.S.A./Canada
120*
Region
Voltage
EU (except U.K.)
230
U.K.
230
China
220
Japan
100
* When operating the monitor with its AC 125-240V power supply, use a power supply cord that matches the power supply
voltage of the AC power outlet being used.
NOTE:
This product can only be serviced in the country where it was purchased.
•
•
The intended primary use of this product is as an Information Technical Equipment in an office or domestic environment.
The product is intended to be connected to a computer and is not intended for the display of television broadcast signals.
English-2
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Precautions, Maintenance & Recommended Use
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
Immediately unplug your monitor from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
•
DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers may
expose you to dangerous shock hazards or other risks. Refer
all servicing to qualified service personnel.
•
•
•
•
•
When the power supply cord or plug is damaged.
If liquid has been spilled, or objects have fallen into the monitor.
If the monitor has been exposed to rain or water.
If the monitor has been dropped or the cabinet damaged.
•
•
Do not spill any liquids into the cabinet or use your monitor
near water.
If you notice any structural damage such as cracks or
unnatural wobbling.
Do not insert objects of any kind into the cabinet slots,
as they may touch dangerous voltage points, which can
be harmful or fatal or may cause electric shock, fire or
equipment failure.
•
If the monitor does not operate normally by following
operating instructions.
Recommended Use
•
•
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
•
•
For optimum performance, allow 20 minutes for warm-up.
Rest your eyes periodically by focusing on an object at least
5 feet away. Blink often.
Do not place this product on a sloping or unstable cart, stand
or table, as the monitor may fall, causing serious damage to
the monitor.
•
•
•
•
Position the monitor at a 90° angle to windows and other light
sources to minimize glare and reflections.
•
•
Do not mount this product face up, face down or upside down
for an extended period of time as it may cause permanent
damage to the screen.
Clean the LCD monitor surface with a lint-free, non-abrasive
cloth. Avoid using any cleaning solution or glass cleaner!
Adjust the monitor’s brightness, contrast and sharpness
controls to enhance readability.
The power supply cord you use must have been approved by
and comply with the safety standards of your country. (Type
H05VV-F 3G 1mm2 should be used in Europe)
Avoid displaying fixed patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
•
•
In UK, use a BS-approved power cord with molded plug
having a black (13A) fuse installed for use with this monitor.
•
Get regular eye checkups.
Do not place any objects onto the monitor and do not use the
monitor outdoors.
Ergonomics
•
The lamps in this product contain mercury. Please
dispose according to state, local or federal law.
Do not bend, crimp or otherwise damage the power cord.
If glass is broken, handle with care.
To realize the maximum ergonomic benefits, we recommend the
following:
•
•
•
•
•
Use the preset Size and Position controls with standard
signals.
Do not cover vent on monitor.
•
•
•
Use the preset Color Setting.
Use non-interlaced signals.
Do not use monitor in high temperature, humid, dusty, or oily
areas.
Do not use primary color blue on a dark background, as
it is difficult to see and may produce eye fatigue due to
insufficient contrast.
•
•
If monitor or glass is broken, do not come in contact with the
liquid crystal and handle with care.
Allow adequate ventilation around the monitor, so that heat
can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources.
Do not put anything on top of the monitor.
Cleaning the LCD Panel
•
When the liquid crystal panel is dusty, please gently wipe
with a soft cloth.
•
•
•
Please do not rub the LCD panel with hard material.
Please do not apply pressure to the LCD surface.
•
The power cable connector is the primary means of detaching
the system from the power supply. The monitor should be
installed close to a power outlet, which is easily accessible.
Please do not use OA cleaner as it will cause deterioration or
discolor on the LCD surface.
•
•
•
•
Handle with care when transporting. Save packaging for
transporting.
Cleaning the Cabinet
If using the cooling fan continuously, it is recommended to
wipe holes clean a minimum of once a month.
•
•
•
Unplug the power supply
Gently wipe the cabinet with a soft cloth
Please clean the holes of back cabinet to reject dirt and dust
at least once a year because of set reliability.
To clean the cabinet, dampen the cloth with a neutral
detergent and water, wipe the cabinet and follow with a dry
cloth.
When using a LAN cable, do not connect to a peripheral
device with wiring that might have excessive voltage.
NOTE: DO NOT clean with benzene thinner, alkaline detergent,
alcoholic system detergent, glass cleaner, wax, polish
cleaner, soap powder, or insecticide. Rubber or vinyl
should not be in contact with the cabinet for an extended
period of time. These types of fluids and materials can
cause the paint to deteriorate, crack or peel.
Connecting to a TV*
•
Cable distribution system should be grounded (earthed) in
accordance with ANSI/NFPA 70, the National Electrical Code
(NEC), in particular Section 820.93, Grounding of Outer
Conductive Shield of a Coaxial Cable.
•
The screen of the coaxial cable is intended to be connected
to earth in the building installation.
* The product you purchased may not have this feature.
English-3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Your new MultiSync monitor box* should contain the following:
•
•
•
•
•
•
LCD monitor
Power cord*1
Video Signal Cable
Wireless Remote Control and AA Batteries
Setup Manual
CD-ROM
Video Signal Cable
(Mini D-SUB 15 pin to
Mini D-SUB 15 pin)
Power Cord*1
Setup Manual
CD-ROM
Setup Manual
Wireless Remote Control
and AA Batteries
*
*
Remember to save your original box and packing material to transport or ship the monitor.
1
Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than one
power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been approved by
and complies with the safety standard of your particular country.
English-4
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory for support. For proper
installation it is strongly recommended to use a trained,
NEC authorized service person. Failure to follow NEC
standard mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding the warranty.
Orientation
•
When using the display in the portrait position, the
monitor should be rotated clockwise so that the left side
is moved to the top and the LED indicator light is on
the bottom. This will allow for proper ventilation and will
extend the lifetime of the monitor. Improper ventilation
may shorten the lifetime of the monitor.
Mounting
DO NOT mount the monitor yourself. Please ask dealer.
For proper installation it is strongly recommended to use
a trained, qualified technician. Please inspect the location
where the unit is to be mounted. Mounting on wall or ceiling
is the customer’s responsibility. Not all walls or ceilings are
capable of supporting the weight of the unit. Product warranty
does not cover damage caused by improper installation,
remodelling, or natural disasters. Failure to comply with these
recommendations could result in voiding the warranty.
DO NOT block ventilated openings with mounting
accessories or other accessories.
LED Indicator
For NEC Qualified Personnel:
Mounting location
To ensure safe installation, use two or more brackets to
mount the unit. Mount the unit to at least two points on the
installation location.
•
•
•
•
•
•
The ceiling and wall must be strong enough to support the
monitor and mounting accessories.
DO NOT install in locations where a door or gate can hit
the unit.
Please note the following when mounting
on wall or ceiling
DO NOT install in areas where the unit will be subjected
to strong vibrations and dust.
•
When using mounting accessories other than those that
are NEC approved, they must comply with the VESA-
compatible (FDMlv1) mounting method.
DO NOT install near where the main power supply enters
the building.
•
NEC strongly recommends
using size M6 screws
Mounting
Bracket
Unit
No gap
Do not install in where people can easily grab and hang
onto the unit or the mounting apparatus.
(10-12 mm + thickness
of bracket and washers in
length). If using screws
longer than 10-12 mm,
No thread
4 mm
Washers
Screw
When mounting in a recessed area, as in a wall, leave at
least 4 inches (100 mm) of space between the monitor
and the wall for proper ventilation.
under
ꢀ 8.5 mm
10-12 mm
Thickness
of bracket
and washers
•
Allow adequate ventilation or provide air conditioning
around the monitor, so that heat can properly dissipate
away from the unit and mounting apparatus.
check the depth of the hole.
(Recommended Fasten
Force: 470 - 635N•cm)
NEC recommends mounting
interfaces that comply with
UL1678 standard in North
America.
Screw length should equal
depth of hole (10-12 mm) + the
thickness of mounting bracket
and washers. Bracket hole
should be under ꢀ 8.5 mm.
Mounting on ceiling
•
Ensure that the ceiling is sturdy enough to support the
weight of the unit and the mounting apparatus over time,
against earthquakes, unexpected vibrations, and other
external forces.
•
Prior to mounting, inspect the installation location to
insure that it is strong enough to support the weight of the
unit so that the unit will be safe from harm.
•
•
Be sure the unit is mounted to a solid structure within
the ceiling, such as a support beam. Secure the monitor
using bolts, spring lock washers, washer and nut.
•
•
Refer to the instructions included with the mounting
equipment for detailed information.
DO NOT mount to areas that have no supporting internal
structure. DO NOT use wood screws or anchor screws for
mounting. DO NOT mount the unit to trim or to hanging
fixtures.
Make sure there is no gap between the monitor and the
bracket.
Maintenance
•
Periodically check for loose screws, gaps, distortions,
or other problems that may occur with the mounting
apparatus. If a problem is detected, please refer to
qualified personnel for service.
•
Regularly check the mounting location for signs of
damage or weakness that may occur over time.
English-5
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Installing and removing optional table
top stand
Attaching Mounting Accessories
The monitor is designed for use with the VESA mounting
system.
CAUTION: Installing and removing the stand must be done
by two or more people.
1. Attach Mounting Accessories
To install, follow those instructions included with the stand or
mounting apparatus. Use only those devices recommended
by the manufacturer.
Be careful to avoid tipping monitor when attaching
accessories.
VESA Mounting Interface
NOTE:
Use ONLY the thumbscrews which are included
with the optional table top stand.
When installing the LCD monitor stand, handle the unit with
care to avoid pinching your fingers.
Optional table top stand
200 mm
Table
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the screen face,
place the protective sheet on the table underneath the LCD.
The protective sheet was wrapped around the LCD in the
original packaging. Make sure there is nothing on the table
that can damage the monitor.
Protective Sheet
NOTE:
Install the stand so the long end of the feet face
forward. Use the ST-322 for V322.
4. Ventilation Requirements
When mounting in an enclosed space or recessed area,
leave adequate room between the monitor and the enclosure
to allow heat to disperse, as shown below.
When using mounting accessories other than NEC compliant
and approved, they must comply with the VESA-compatible
mounting method.
2. Using Option Board
1. Turn off the main power switch.
2. Remove the attached slot cover by unscrewing the
installed screws (Figure 1).
3. Insert option board in to the monitor.
NOTE:
Please contact your supplier for available option
boards.
Do not apply excessive force to manipulate the
optional board before fixing it with screws.
Allow adequate ventilation or provide air conditioning around
the monitor, so that heat can properly dissipate away from
the unit and mounting apparatus; especially when you use
monitors in multiple screen.
NOTE:
The sound quality of the internal speakers will
differ according to the acoustics of the room.
Figure 1
English-6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Prevent Tipping
When using the display with the optional table top stand
fasten the LCD to a wall using a cord or chain that can
support the weight of the monitor in order to prevent the
monitor from falling. Fasten the cord or chain to the monitor
using the provided clamps and screws.
200 mm
Screw Holes
Cord or chain
Clamp*
Screw (M4)*
*: included in option stand.
Before attaching the LCD monitor to the wall, make sure that
the wall can support the weight of the monitor.
Be sure to remove the cord or chain from the wall before
moving the LCD.
English-7
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts Name and Functions
Control Panel
³ POWER button
º EXIT button
Switches the power on/off. See also page 16.
Activates the OSD menu when the OSD menu is turned-off.
Acts as EXIT button within the OSD to move to previous
menu.
· MUTE button
Switches the audio mute ON/OFF.
¾ Remote control sensor and Power Indicator
» INPUT button
Receives the signal from the remote control (when using the
wireless remote control). See also page 11.
Acts as SET button within OSD menu. (Toggle switches
between [DVI], [DPORT], [VGA], [HDMI], [DVD/HD],
[SCART], [VIDEO1], [VIDEO2] or [S-VIDEO]). These are
available input only, shown as their factory preset name.
Glows green when the LCD monitor is in active mode*.
Glows red when the LCD is in POWER OFF mode.
Glows amber when the monitor is in Power Save Mode.
Green and Amber blink alternately while in Power Standby
mode with the “SCHEDULE SETTINGS” function enabled.
When a component failure is detected within the monitor, the
indicator will blink red.
¿ PLUS button
Acts as (+) button to increase the adjustment with OSD menu.
Increases the audio output level when the OSD menu is
turned off.
* If “OFF” is selected in “POWER INDICATOR” (see page 23),
LED will not light when the LCD monitor is in active mode.
´ MINUS button
Acts as (-) button to decrease the adjustment with OSD menu.
Decreases the audio output level when the OSD menu is
turned off.
µ AMBIENT LIGHT SENSOR
Detects the level of ambient light, allowing the monitor
to make automatic adjustments to the backlight setting,
resulting in a more comfortable viewing experience. Do not
cover this sensor. See page 18.
² UP button
Control Key Lock Mode
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area up to select
adjustment items within OSD menu.
This control completely locks out access to all Control Key
functions. To activate the control key lock function, press
both and and hold down simultaneously for more than
3 seconds. To resume user mode, press both and and
hold simultaneously for more than 3 seconds.
¶ DOWN button
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area down to select
adjustment items within OSD menu.
English-8
Download from Www.Somanuals.com. All Manuals Search And Download.
Terminal Panel
³ AC IN connector
¾VGA IN (mini D-Sub 15 pin)
Connects with the supplied power cord.
To input analog RGB signals from a personal computer or
from other RGB equipment. This input can be used with an
RGB, COMPONENT, SCART, VIDEO or S-VIDEO source.
Please select signal type in TERMINAL SETTING.
See page 25.
· Main Power Switch
On/Off switch to turn main power ON/OFF.
» LAN port (RJ-45)
LAN connection. See page 32.
NOTE: When you use this connector for COMPONENT,
SCART, VIDEO or S-VIDEO, please use a suitable signal
cable. If you have any questions, please ask your dealer.
¿ REMOTE IN/OUT
Use the optional wired remote control by connecting it to your
monitor.
µVIDEO1 IN connector (BNC)
To input a composite video signal.
¸ AUDIO IN 1
To input audio signal from external equipment such as a
computer, VCR or DVD player.
NOTE: When you use Remote IN/OUT, IR CONTROL in OSD
menu should be NORMAL.
NOTE: Do not use this connector unless specified.
´ RS-232C (D-Sub 9 pin)
¹ AUDIO OUT
IN connector: Connect RS-232C input from external
equipment such as a PC in order to control RS-232C
functions.
To output the audio signal from the AUDIO IN 1, DPORT and
HDMI to an external device (stereo receiver, amplifier, etc.).
OUT connector: Connect RS-232C output. To connect
multiple MultiSync monitors via RS-232C daisy Chain.
Ƹ Kensington Lock
For security and theft prevention.
² DISPLAYPORT connector
To input DisplayPort signals.
ƹ Option board slot
Slot 2 type accessories are available. Please contact your
supplier for detailed information.
¶ DVI connector (DVI-D)
IN connector: To input digital RGB signals from a computer
or HDTV device having a digital RGB output.
NOTE: Please contact your supplier for available option
board.
* This connector does not support analog input.
ƺ Internal speaker
OUT connector: To output the DVI signal from either DVI IN
or HDMI connection. To output the DVI signal from the HDMI
connection, the HDMI input must be selected.
º HDMI connector
To input digital HDMI signals.
English-9
Download from Www.Somanuals.com. All Manuals Search And Download.
Wireless Remote Control
¿ ASPECT button
Selects picture aspect, [FULL], [WIDE], [DYNAMIC], [1:1],
[ZOOM] and [NORMAL]. See page 17.
´ SOUND button
Artificial surround sound for internal/external speakers.
Audio out is disabled when surround is set to ON.
² KEYPAD
Press buttons to set and change passwords, change channel
and set REMOTE ID.
¶ ENT button*2
º DISPLAY button
Turns on/off the information OSD. See page 18.
¾ MENU button
Turns on/off the menu mode.
µ AUTO SETUP button
Enters auto setup menu. See page 20.
¸ EXIT button
Returns to previous menu within OSD menu.
¹ UP/DOWN button
Acts as
button to move the highlighted area up or down
to select adjustment items within OSD menu.
Small screen which adjusted “PIP” mode moves up or down.
Ƹ MINUS/PLUS (-/+) button
Increases or decreases the adjustment level within OSD
menu settings.
³ POWER button
Switches the power on/standby.
Small screen which adjusted “PIP” mode moves left or right.
· INPUT button
Selects input signal.
DVI: DVI
ƹ SET button
Makes selection.
DISPLAYPORT: DPORT
VGA: VGA
HDMI: HDMI
DVD/HD: DVD/HD, SCART
VIDEO: VIDEO1, VIDEO2
S-VIDEO: S-VIDEO
OPTION: Depends on your connection
ƺVOLUME UP/DOWN button
Increases or decreases audio output level.
ƻ CH UP/DOWN button*2
Ƽ GUIDE button*2
» PICTURE MODE button
Selects picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA], [AMBIENT1], [AMBIENT2]. See page 18.
ƽ MUTE button
Turns on/off mute function.
ƾ STILL button
ON/OFF button: Activates/deactivates still picture mode.
STILL CAPTURE button: Captures still picture.
HIGHBRIGHT: for moving images such as DVD.
STANDARD: for images.
sRGB: for text based images.
CINEMA: for movies.
AMBIENT1 and AMBIENT2: activate auto dimming
function. See page 18.
English-10
Download from Www.Somanuals.com. All Manuals Search And Download.
ƿ PIP (Picture In Picture) button
ON/OFF button: Toggle switches between PIP, POP,
PICTURE BY PICTURE-ASPECT and PICTURE BY
PICTURE-FULL. See page 22.
INPUT button: Selects the “picture in picture” input signal.
CHANGE button: Replaces to the main picture and sub
picture.
Operating Range for the Remote
Control
Point the top of the remote control toward the LCD monitor’s
remote sensor during button operation.
Use the remote control within a distance of about 7 m (23 ft.)
from remote control sensor or at a horizontal and vertical
angle of within 30° within a distance of about 3.5 m (10 ft.).
Sub picture
DVI
No
DPORT
Yes
No
VGA
Yes
Yes
No
HDMI
No
DVD/HD SCART VIDEO1 VIDEO2 S-VIDEO
DVI
Yes
Yes
No
Yes
Yes
No
Yes
No
No
No
No
No
Yes
Yes
Yes
Yes
Yes
No
Yes
Yes
No
Yes
No
No
No
No
No
Yes
Yes
No
Yes
No
No
No
No
No
DPORT
VGA
Yes
Yes
No
Yes
Yes
No
Yes
Yes
Yes
Yes
Yes
Yes
Yes
HDMI
Yes
No
Yes
No
DVD/HD
SCART
VIDEO1
VIDEO2
S-VIDEO
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
No
No
Yes
No
Yes
No
No
No
No
No
No
REMOTE ID button
Activates REMOTE ID function.
MTS button*2
Caution: Important, the remote control
system may not function
AUDIO INPUT button
Selects audio input source [IN1], [DPORT], [HDMI],
[OPTION]*1.
when direct sunlight or strong
illumination strikes the remote
control sensor or when there is
an object in the path.
button
Activates closed captioning.
Note: VIDEO1, VIDEO2, S-VIDEO inputs only.
*1: The product you purchased may not have this feature.
Handling the remote control
•
•
Do not subject to strong shock.
*2: This button’s action depends on which option board you use.
Refer to the option board’s manual for further information.
Do not allow water or other liquid to splash
the remote control. If the remote control gets
wet, wipe it dry immediately.
•
•
Avoid exposure to heat and steam.
Other than to install the batteries, do not open the remote
control.
English-11
Download from Www.Somanuals.com. All Manuals Search And Download.
Setup
NEC recommends the following battery use:
1. Determine the installation location
CAUTION: Installing your LCD monitor must be done by a
qualified technician. Contact your dealer for more
information.
•
Place “AA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
•
•
Do not mix battery brands.
CAUTION: MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY TWO OR MORE PEOPLE.
Failure to follow this caution may result in injury if
the LCD monitor falls.
Do not combine new and old batteries. This can shorten
battery life or cause liquid leakage of batteries.
•
Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
CAUTION: Do not mount or operate the monitor upside
•
Do not touch exposed battery acid, it may injure skin.
down, face up or face down.
NOTE:
If you do not intend to use the Remote Control for
a long period of time, remove the batteries.
CAUTION: This LCD has a temperature sensor and cooling
fans, including a fan for option board.
If the LCD becomes too hot, the cooling fans will
turn on automatically.
3. Connect external equipment
(See pages 14 and 15)
The fan of option board is active although the
temperature is lower than normal operating
temperature for cooling option board. If the LCD
becomes overheated while the cooling fan is
running, a “Caution” warning will appear. If the
“Caution” warning appears, discontinue use and
allow the unit to cool. Using the cooling fan will
reduce the likelihood of early circuit failure and
may help reduce image degradation and “Image
Persistance”.
If the LCD is used in an enclosed area or if the
LCD panel is covered with a protective screen,
please check the inside temperature of the
monitor by using the “HEAT STATUS” control
in the OSD (see page 24). If the temperature is
higher than the normal operating temperature,
please turn the cooling fan to ON within the FAN
CONTROL menu within the OSD (see page 24).
•
To protect the external equipment; turn off the main power
before making connections.
•
Refer to your equipment user manual for further
information.
NOTE:
Do not connect/disconnect cables when turning
on the monitor or other external equipment as this
may result in a loss of the monitor image.
4. Connect the supplied power cord
•
The equipment should be installed close to an easily
accessible power outlet.
•
Fully insert the prongs into the power outlet socket.
A loose connection may cause image degradation.
NOTE:
Please refer to the “Safety Precautions and
Maintenance” section of this manual for proper
selection of AC power cord.
IMPORTANT: Lay the protective sheet, which was wrapped
around the LCD monitor when it was
packaged, beneath the LCD monitor so as not
to scratch the panel.
2. Install the remote control batteries
The remote control is powered by two 1.5V AA batteries.
To install or replace batteries:
A. Press and slide to open the cover.
B. Align the batteries according to the (+) and (–) indications
inside the case.
C. Replace the cover.
CAUTION: Incorrect usage of batteries can result in leaks or
bursting.
English-12
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Switch on the power of all the attached
external equipment
When connected with a computer, switch on the power of the
computer first.
6. Operate the attached external equipment
Display the signal from the desired input source.
7. Adjust the sound
Make volume adjustments when required.
8. Adjust the screen (See pages 20 and 21)
Make adjustments of the screen display position when
necessary.
9. Adjust the image (See page 20)
Make adjustments such as backlight or contrast when
required.
10. Recommended Adjustments
To reduce the risk of the “Image Persistence”, please adjust
the following items based on the application being used:
“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 24)
“DATE & TIME”, “SCHEDULE SETTINGS” (See page 21).
It is recommended that the “FAN CONTROL” setting
(See page 24) be turned to ON also.
English-13
Download from Www.Somanuals.com. All Manuals Search And Download.
Connections
NOTE:
Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a
loss of the monitor image.
NOTE:
Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
Before making connections:
*
*
First turn off the power of all the attached equipment and make connections.
Refer to the user manual included with each separate piece of equipment.
Wiring Diagram
Solid lines = video signal
Dotted lines = audio signal
DVD player
Stereo Amplifier
Second monitor*
DVD player
with HDMI out
VCR or
DVD Player
DVD player with
SCART OUT
Computer (Analog)
Computer (Digital)
*: Multiple monitors that are daisy-chained have a limit to the connectable monitors.
Connected
equipment
Connecting
terminal
Connecting
Audio terminal in remote control
Input button
Setting in Terminal Mode
Input signal name
DVI (DVI-D)
HDMI
DVI MODE: DVI-HD
RAW/EXPAND*1
D-SUB MODE: SCART
-
DVI
HDMI
AUDIO IN1
HDMI
DVI
HDMI
DVD/HD
VIDEO
S-VIDEO
VIDEO
DVD/HD
VGA
VGA (D-Sub) +VIDEO1
VIDEO1 (BNC)
VGA (D-Sub)
VGA (D-Sub)
VGA (D-Sub)
VGA (D-Sub)
DVI (DVI-D)
DisplayPort
SCART
VIDEO1
S-VIDEO
VIDEO2
DVD/HD2
VGA
DVI
DPORT
HDMI
AUDIO IN1
AUDIO IN1
AUDIO IN1
AUDIO IN1
AUDIO IN1
AUDIO IN1
AUDIO IN1
DPORT
AV
D-SUB MODE: S-VIDEO
D-SUB MODE: VIDEO
D-SUB MODE: COMPONENT
-
DVI MODE: DVI-PC
-
DVI
PC
DISPLAYPORT
HDMI
HDMI
RAW/EXPAND*1
HDMI
*1: depend on signal type.
English-14
Download from Www.Somanuals.com. All Manuals Search And Download.
Connecting a Personal Computer
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.
Some video cards with a pixel clock over 162MHz may not display an image correctly.
Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.
<Typical factory preset signal timing>
Scanning frequency
Horizontal Vertical
Remarks
Resolution
640 x 480
800 x 600
31.5 kHz
37.9 kHz
48.4 kHz
48 kHz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
60 Hz
1024 x 768
1280 x 768
1360 x 768
1280 x 1024
1600 x 1200
1920 x 1080
48 kHz
Recommended resolution
Compressed image
Compressed image
Compressed image
64 kHz
75 kHz
67.5 kHz
•
If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook.
Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any
special identification or configuration your monitor’s image and monitor may require.
•
•
Input TMDS signals conforming to DVI standards.
To maintain display quality, use a cable that conforms to DVI standards.
Connecting a DVD Player or Computer with HDMI out
•
•
•
Please use an HDMI cable with HDMI logo.
It may take a moment for the signal to appear.
Some video cards or drivers may not display an image correctly.
Connecting a Computer with DisplayPort
•
•
•
•
Please use DisplayPort cable with DisplayPort compliance logo.
It may take a moment for the signal to appear.
Please note that DisplayPort connector does not supply power to the connected component.
Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not
appear.
•
Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the lock.
English-15
Download from Www.Somanuals.com. All Manuals Search And Download.
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.
NOTE:
The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the
Power Button on the front of the LCD.
Main Power Switch
OFF
ON
Power Button
Using the remote control
POWER ON Button
English-16
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Indicator
Picture Aspect
DVI, VGA, DPORT
Mode
Status Indicator Light
Green*1
FULL
1:1
ZOOM
NORMAL
Power ON
Power OFF
Red
HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO
Power consumption under 0.5 W
Power Save
Power consumption under 1 W*2
Amber
FULL
WIDE
DYNAMIC
1:1
ZOOM
NORMAL
Power Standby when “SCHEDULE
SETTINGS” enabled
Diagnosis (Detecting failure)
Green and Amber blink alternately
Aspect ratio
of image
Recommended selection
for picture aspect*3
Unchanged view*3
Red Blinking
(See Troubleshooting page 37)
NORMAL
*1 If “OFF” is selected in POWER INDICATOR (page 23), the LED will not light when the
LCD monitor is in active mode.
*2 Without any option, with factory settings, VGA input only.
4:3
DYNAMIC
FULL
Using Power Management
The LCD monitor follows the VESA approved DPM Display
Power Management function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fixed period.
The power management feature on your new display has
been set to the “ON” mode. This allows your display to
enter a Power Saving Mode when no signal is applied. This
could potentially increase the life and decrease the power
consumption of the display.
Squeeze
Letterbox
WIDE
*3 Grey areas indicate unused portions of the screen.
NOTE:
Depending on the PC and video card used, this
function may not operate.
NORMAL: Displays the aspect ratio the same as it is sent
from the source.
NOTE:
It takes about 10 minutes for the monitor to go into
power management mode when using DVD/HD,
SCART, VIDEO1, VIDEO2 and S-VIDEO.
FULL: Fills entire screen.
WIDE: Expands a 16:9 letter box signal to fill entire screen.
DYNAMIC: Expands a 4:3 pictures to fill the entire screen
with non-linearity. Some of the outside image area will be cut
off due to expansion.
Selecting a video source
To view a video source:
1:1: Displays the image in a 1 by 1 pixel format.
Use the input button to set [VIDEO1], [VIDEO2], [S-VIDEO].
ZOOM
The image can be expanded beyond the active display area.
The image which is outside of active display area is not
shown.
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your
video format.
ZOOM
ZOOM
English-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Information OSD
The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc.
Press the DISPLAY button on the remote to bring up the Information OSD.
1
ᕡ
ᕢ
ᕣ
ᕤ
ᕥ
ᕦ
ᕧ
ID number assigned to current monitor*
2
ID number assigned monitor to be controlled via RS-232C*
Input Name
Audio input mode
Picture aspect
Input Signal Information
Sub picture information
*1: “IR CONTROL” should be set “Primary” or “Secondary”.
*2: “IR CONTROL” should be set “Primary”.
Picture Mode
DVI, VGA, DPORT
STANDARD
sRGB
AMBIENT1
AMBIENT2
HIGHBRIGHT
HDMI, DVD/HD, SCART, VIDEO1, VIDEO2, S-VIDEO
STANDARD CINEMA AMBIENT1 AMBIENT2
HIGHBRIGHT
AMBIENT Mode
The backlight of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the room.
If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim accordingly. The
purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting conditions.
NOTE:
When picture mode is set to AMBIENT1 or AMBIENT2, BACKLIGHT, AUTO BRIGHTNESS and BACKLIGHT in
SCREEN SAVER function are disabled.
Do not cover Ambient light sensor when you use AMBIENT1 or AMBIENT2 in PICTURE MODE.
AMBIENT parameter setting
PICTURE MODE in OSD, select AMBIENT1 or AMBIENT2 and set IN BRIGHT and IN DARK in each mode.
IN BRIGHT: This is the backlight level that the monitor will go up to when the ambient light level is highest.
IN DARK: This is the level of backlight that the monitor will go down to when the ambient light level is low.
When the AMBIENT function is enabled the Backlight level of the screen changes automatically according to the lighting
conditions of the room (Figure 1).
Factory Setting
BACKLIGHT range
BACKLIGHT level set
for the monitor to use
when ambient lighting
level is low.
BACKLIGHT level set for the
monitor to use when ambient
lighting level is high.
IN DARK
IN BRIGHT
room bright condition
dark
bright
Screen Backlight value by AMBIENT1 mode
Screen Backlight value by AMBIENT2 mode
Figure 1
IN DARK:
BACKLIGHT level set for the monitor to use when ambient lighting level is low.
IN BRIGHT: BACKLIGHT level set for the monitor to use when ambient lighting level is high.
English-18
Download from Www.Somanuals.com. All Manuals Search And Download.
OSD (On-Screen-Display) Controls
NOTE:
Some functions may not be available depending on the model or optional equipment.
Input source
Main Menu Icons
Main Menu Item
70
50
50
50
Adjustment Settings
50
Sub Menu
50
THANK YOU FOR SAVING
THE ENVIRONMENT.
CARBON FOOTPRINT
86.0 %
PICTURE MODE
Goto Adjustment Return
Close
Select
Key Guide
Press UP or DOWN
button to select
sub-menu.
Press SET.
Press UP or DOWN,
PLUS or MINUS to select
the function or setting to
be adjusted.
Press MENU or EXIT.
Remote Control
Press UP or DOWN
button to select.
Press INPUT button
to decide.
Press UP or DOWN, PLUS
or MINUS button to select.
Press EXIT
Control Panel
OSD screen
English-19
Download from Www.Somanuals.com. All Manuals Search And Download.
Setting
Default
PICTURE
BACKLIGHT
Adjusts the overall image and background brightness. Press + or - to adjust.
Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot be
changed.
70
CONTRAST
Adjusts the image brightness in relationship to the input signal. Press + or - to adjust.
Note: When sRGB is selected in picture mode, this function cannot be changed.
50
SHARPNESS
BRIGHTNESS
Adjusts the crispness of the image. Press + or - to adjust.
50*
50
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Note: When sRGB is selected in picture mode, this function cannot be changed.
HUE
Adjusts the hue of the screen. Press + or - to adjust.
Note: When sRGB is selected in picture mode, this function cannot be changed.
50
50*
COLOR
Adjusts the color depth of the screen. Press + or - to adjust.
Note: When sRGB is selected in picture mode, this function cannot be changed.
COLOR TEMPERATURE
Adjusts the color temperature of the entire screen. A low color temperature will make the screen
reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further
adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the R/G/B
levels, CUSTOM must be showing as the COLOR TEMP selection.
10000K
Note: When sRGB is selected in picture mode, predefined 6500k is set so it cannot be changed.
When PROGRAMMABLE is selected in GAMMA CORRECTION, this function cannot be
changed.
COLOR CONTROL
Adjusts the hue of the Red, Yellow, Green, Cyan, Blue and Magenta.
0
Note: When sRGB is selected in picture mode, this function cannot be changed.
GAMMA CORRECTION
Select a display gamma for best picture quality.
Note: When sRGB is selected in picture mode, this function cannot be changed.
NATIVE*
(except sRGB
setting)
NATIVE
2.2
Gamma correction is handled by the LCD panel.
Typical display gamma for use with a PC.
Good for video (DVD, etc.)
2.4
S GAMMA
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts of the
image (S-Curve).
DICOM SIM.
DICOM GSDF curve simulated for LCD type.
PROGRAMMABLE
MOVIE SETTINGS
A programmable gamma curve can be loaded using NEC optional software.
NOISE REDUCTION
Adjusts the amount of noise reduction. Press + or - to adjust.
0*
VIDEO1, VIDEO2, S-VIDEO inputs only
TELECINE
Automatically senses the sources frame rate for optimal picture quality.
AUTO*
HDMI, DVD/HD, SCART, VIDEO1,
VIDEO2, S-VIDEO inputs only
ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast.
OFF
HDMI, DVD/HD, SCART, VIDEO1,
VIDEO2, S-VIDEO inputs only
PICTURE MODE
RESET
Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1] or
[AMBIENT2]. See page 18.
STANDARD
-
Resets the following settings within the PICTURE menu back to factory setting: BACKLIGHT,
CONTRAST, SHARPNESS, BRIGHTNESS, HUE, COLOR, COLOR TEMPERATURE,
COLOR CONTROL, GAMMA CORRECTION, MOVIE SETTINGS.
ADJUST
AUTO SETUP
Automatically adjusts Screen Size, H position, V position, Clock, Phase and White Level.
H Position, V Position and Phase are adjusted automatically when new timing is detected.
-
OFF
-
VGA input only
AUTO ADJUST
VGA input only
H POSITION
Controls the horizontal position of the image within the Display area of the LCD.
Press + to move right. Press - to move left.
All inputs except DVI, HDMI, DPORT
V POSITION
Controls the vertical position of the image within the Display area of the LCD.
Press + to move up. Press - to move down.
-
-
-
All inputs except DVI, HDMI, DPORT
CLOCK
Press + to expand the width of the image on the right of the screen.
Press - to narrow the width of the image on the left.
VGA input only
PHASE
Adjusts the visual “noise” on the image.
VGA, DVD/HD, SCART inputs only
*: depends on signal input
English-20
Download from Www.Somanuals.com. All Manuals Search And Download.
H RESOLUTION
Adjusts the horizontal size of the image.
Adjusts the vertical size of the image.
-
-
VGA input only
V RESOLUTION
VGA input only
INPUT RESOLUTION
If there is a problem with signal detection, this function forces the monitor to display the signal at
the desired resolution. After selection, execute “AUTO SETUP” if required.
If no problem is detected, the only available option will be “AUTO”.
AUTO
VGA input only
ASPECT
NORMAL
FULL
Select the aspect ratio of the screen image.
Displays the aspect ratio the same as it is sent from the source.
Fills entire screen.
FULL
-
-
-
-
WIDE
Expands a 16:9 letter box signal to fill entire screen.
DYNAMIC
Expands a 4:3 pictures to fill the entire screen with non-linearity. Some of the outside image area
will be cut off due to expansion. TILE MATRIX becomes invalid.
1:1
Display the image in a 1 by 1 pixel format. (If the input resolution is higher than a 1920 x 1080
resolution, the image will be scaled down to fit the screen). TILE MATRIX becomes invalid.
-
-
-
ZOOM
The image can be expanded beyond the active display area. The image which is outside of active
display area is not shown.
ZOOM
H ZOOM
V ZOOM
H POS
Maintains the aspect ratio while zooming.
Amount of horizontal zoom.
Amount of vertical zoom.
Horizontal position.
V POS
Vertical position.
RESET
Resets the following settings within the ADJUST menu back to factory setting: AUTO ADJUST,
H POSITION, V POSITION, CLOCK, PHASE, H RESOLUTION, V RESOLUTION, ASPECT.
-
AUDIO
VOLUME
BALANCE
Increases or decreases output volume level.
40
Adjust the balance of L/R volume.
CENTER
Press + button to move the stereo sound image to right.
Press - button to move the stereo sound image to left.
TREBLE
BASS
To accentuate or reduce the high frequency sound.
Press + button to increase TREBLE sound.
Press - button to decrease TREBLE sound.
0
0
To accentuate or reduce the low frequency sound.
Press + button to increase BASS sound.
Press - button to decrease BASS sound.
SURROUND
Artificial surround sound.
OFF
Note: Audio out is disabled when this function is set to ON.
PIP AUDIO
LINE OUT
Selects source of PIP audio.
MAIN AUDIO
FIXED
Selecting “VARIABLE” enables control of the line out level with the VOLUME button.
Note: Audio out is disabled when this function is set to ON.
AUDIO INPUT
RESET
Selects audio input source [IN1], [DPORT], [HDMI], [OPTION]*.
Depend on
signal input
Resets “AUDIO” options back to factory settings except VOLUME.
-
SCHEDULE
OFF TIMER
Sets the monitor to power off after a length of time.
A time between 1 to 24 hours is available.
OFF
SCHEDULE SETTINGS
SCHEDULE LIST
DATE & TIME
Creates a working schedule for the monitor to use.
List of schedules.
-
-
Sets the date, time, and daylight saving region. Date & time must be set in order for the
“SCHEDULE” function to operate. See page 27.
YEAR
MONTH
DAY
Configures the year for the real time clock.
Configures the month for the real-time clock.
Configures the day for the real-time clock.
-
-
-
*: The product you purchased may not have this feature.
English-21
Download from Www.Somanuals.com. All Manuals Search And Download.
TIME
Configures the time for the real-time clock.
Configures daylight savings on or off.
-
OFF
-
DAYLIGHT SAVING
RESET
Resets the following settings within the SCHEDULE menu back to factory setting: OFF TIMER,
SCHEDULE SETTINGS.
PIP
KEEP PIP MODE
Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.
When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.
OFF
OFF
PIP MODE
OFF
Selects Picture-in-Picture mode.
Normal mode.
PIP
Picture in Picture mode.
Picture out Picture mode.
POP
PICTURE BY PICTURE- Picture by picture (split screen) mode, with keep aspect.
ASPECT
PICTURE BY PICTURE
FULL
-
Picture by picture (split screen) mode, with full screen.
PIP SIZE
Selects the size of the sub-picture used in Picture-in-Picture (PIP) mode.
LARGE
SMALL
MIDDLE
LARGE
PIP POSITION
ASPECT
TEXT TICKER
MODE
Determines where the PIP appears on the screen.
X = 95, Y = 92
FULL
Selects sub picture aspect, [FULL], [NORMAL] and [WIDE]. See page 17.
OFF
Enables Text Ticker and allows you to set Horizontal or Vertical direction.
Selects the location of the Text Ticker on the screen.
Determines the size of the Text Ticker in relationship to the overall screen size.
Sets the transparency of the Text Ticker (0: transparent, 100: opaque).
Enables auto-detection of the Text Ticker.
POSITION
SIZE
BLEND
DETECT
FADE IN
SUB INPUT
Enables fade-in of the text ticker.
Selects sub picture input signal.
Depends on
signal input
RESET
Resets PIP options back to factory settings except ASPECT and SUB INPUT.
Select the language used by the OSD.
-
OSD
LANGUAGE
ENGLISH
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SVENSKA
РУССКИЙ
ENGLISH
(Depends on
destination)
MENU DISPLAY TIME
Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.
Determines the location where the OSD appears on the screen.
30 Sec.
OSD POSITION
UP
X = 128, Y = 225
DOWN
LEFT
RIGHT
English-22
Download from Www.Somanuals.com. All Manuals Search And Download.
INFORMATION OSD
Selects whether the information OSD is displayed or not. The information OSD will be displayed
when the input signal or source changes. The information OSD will also give a warning when
there is no-signal or the signal is out-of range.
ON, 3 Sec.
An interval between 3 to 10 seconds for the Information OSD to appear is available.
MONITOR INFORMATION
Indicates the model and serial number of your monitor.
-
CARBON SAVINGS: Display the estimated carbon saving information in kg-CO2. The carbon
footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).
CARBON USAGE: Display the estimated carbon usage information in kg-CO2. This is the
arithmetic estimation, not actual measurement value. This estimation is based without any
options.
OSD TRANSPARENCY
OSD ROTATION
LANDSCAPE
Set the transparency of the OSD.
ON
Determines the OSD display direction between landscape and portrait.
Display the OSD with landscape mode.
LANDSCAPE
PORTRAIT
Display the OSD with portrait mode.
INPUT NAME
You can create a name for the INPUT currently being used.
-
Max: 8 characters, including Space, A-Z, 0-9, and some symbols.
CLOSED CAPTION
Activates closed captioning.
OFF
-
VIDEO1, VIDEO2, S-VIDEO inputs only
RESET
Resets the following settings within the OSD menu back to factory setting:
MENU DISPLAY TIME, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY,
CLOSED CAPTION.
MULTI DISPLAY
CONTROL ID
Sets the monitor ID number from 1-100 and group ID from A-J. When “YES” is selected in
“AUTO ID”, monitor ID numbers are set automatically in all monitors which follow in the chain with
RS-232C.
1
NOTE: Group ID is made of multiple selections.
IR CONTROL
Selects the mode of the monitor for use with the infra-red remote control when using the
RS-232C daisy chain.
NORMAL
NORMAL
PRIMARY
SECONDARY
LOCK
The monitor will be controlled normally using the remote controller.
Choose “PRIMARY” for the first monitor within an RS-232C daisy chain.
Choose “SECONDARY” for all subsequent monitors within an RS-232C daisy chain.
Prevents the monitor from being controlled by the wireless remote controller. To return to normal
operation, press the “DISPLAY” button on the remote controller for 5 seconds.
TILE MATRIX
Allows one image to be expanded and displayed over multiple screens (up to 100) through a
distribution amplifier.
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate
without a distribution amplifier at a lower number of screens.
H MONITORS
V MONITORS
POSITION
Number of monitors arranged horizontally.
1
Number of monitors arranged vertically.
1
1
Select which section of the tiled image to be displayed on the monitor.
Turns the TILE COMP feature on.
TILE COMP
NO
ENABLE
Enables Tile Matrix.
NO
TILE MATRIX MEM
POWER ON DELAY
When “INPUT” is selected, TILE MATRIX setting is applied to each signal input.
COMMON
0 Sec.
Adjusts the delay time between being in “standby” mode and entering “power on” mode.
“POWER ON DELAY” can be set between 0 and 50 seconds.
POWER INDICATOR
Turns ON or OFF the LED located at the front of the monitor.
ON
If “OFF” is selected, LED will not light when the LCD monitor is in active mode.
EXTERNAL CONTROL
CONTROL
Selects the control interface, RS-232C or LAN.
Resets the LAN settings.
RS-232C
LAN RESET
-
ID=ALL REPLY
When controlling the monitor externally, select if the communication command, which specifies
destination equipment ID (ALL or GROUP ID), is replying or not. When you need reply, please
select “ON”.
OFF
If you connect the multiple monitors that are daisy-chained from second monitor by RS-232C,
you need to select “OFF” from second monitor.
MAC ADDRESS
Displays the MAC ADDRESS.
-
English-23
Download from Www.Somanuals.com. All Manuals Search And Download.
LAN SETTING
DHCP
When you use this function, EXTERNAL CONTROL should be “LAN”.
NOTE: When changing the LAN SETTING, you need to wait several seconds until the LAN
SETTING is applied.
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
DISABLE
NOTE: Consult your network administrator for the IP address when “ENABLE” is selected for
[DHCP].
IP ADDRESS
Set your IP address of the network connected to the monitor when “DISABLE” is selected for
[DHCP].
192.168.0.10
255.255.255.0
192.168.0.1
SUBNET MASK
DEFAULT GATEWAY
Set your subnet mask number of the network connected to the monitor when “DISABLE” is
selected for [DHCP].
Set your default gateway of the network connected to the monitor when “DISABLE” is selected
for [DHCP].
DNS PRIMARY
DNS SECONDARY
SETTING COPY
Set your primary DNS settings of the network connected to the monitor.
Set your secondary DNS settings of the network connected to the monitor.
0.0.0.0
0.0.0.0
NO
In a daisy chain scenario, select the OSD menu categories that you want to copy over to the
other monitor.
NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”. This function
resets to default when power is off. This function has a limit depending on the cable you use.
COPY START
ALL INPUT
RESET
Select “YES” and press the SET button to start copying.
All input terminals settings are copied when you select this item. Default is off.
Resets “MULTI DISPLAY” options back to factory settings except LAN SETTING and TILE
MATRIX MEM.
-
DISPLAY PROTECTION
POWER SAVE
Sets how long the monitor waits to go into power save mode after the signal is lost.
ON
Note: When connecting DVI, the video card might not stop sending the digital data even
though the image might have disappeared. If this occurs the monitor will not switch into power
management mode.
HEAT STATUS
FAN CONTROL
Displays status of the FAN, BACKLIGHT and TEMPERATURE.
-
Cooling fan reduces the temperature of the display to protect from overheating.
AUTO
If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.
SCREEN SAVER
GAMMA
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
The display gamma is changed and fixed when “ON” is selected.
OFF
OFF
BACKLIGHT
The brightness of backlight is decreased when “ON” is selected.
NOTE: Do not select this function when picture mode is AMBIENT1 or AMBIENT2.
MOTION
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT) at
user determined intervals. You can set interval time and zooming ratio.
This function is disabled when PIP, STILL, TEXT TICKER or TILE MATRIX are enabled.
OFF
15
SIDE BORDER COLOR
Adjusts the color of the side borders when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
AUTO BRIGHTNESS
Adjusts the brightness level according to the input signal.
NOTE: Do not select this function when picture mode is AMBIENT1 or AMBIENT2.
OFF
-
DPORT, DVI, VGA inputs only
CHANGE SECURITY
PASSWORD
Allows the security password to be changed.
The factory preset password is 0000.
SECURITY
DDC/CI
Locks the security password.
OFF
ENABLE
OFF
ENABLE/DISABLE: Turns ON or OFF the two way communication and control of the monitor.
Selects whether or not to send an e-mail notification of monitor error via wired LAN.
ALERT MAIL
RESET
Resets the following settings within the DISPLAY PROTECTION menu back to factory
setting: POWER SAVE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR, AUTO
BRIGHTNESS, DDC/CI.
-
English-24
Download from Www.Somanuals.com. All Manuals Search And Download.
ADVANCED OPTION
INPUT DETECT
Selects the method of input detection the monitor uses when more than two input devices are
connected.
NONE
NONE
The Monitor will not search the other video input ports.
FIRST DETECT
When the current video input signal is not present, then the monitor searches for a video signal
from the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
The monitor will not look for other video signals while the current video source is present.
LAST DETECT
VIDEO DETECT
When the monitor is displaying a signal from the current source and a new secondary source
is supplied to the monitor, the monitor will automatically switch to the new video source. When
current video input signal is not present, the monitor searches for a video signal from the other
video input port. If the video signal is present in the other port, then the monitor switches the
video source input port to the new found video source automatically.
DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO inputs will have priority over DVI, VGA. When
DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO input signal is present the monitor will change
and keep to the DVD/HD, SCART, VIDEO1, VIDEO2 or S-VIDEO input.
CUSTOM DETECT
INPUT CHANGE
Set the priority of input signals.
When CUSTOM DETECT is selected, monitor searches listed inputs only.
Sets input change speed.
NORMAL
NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.
This function should be chosen after all adjustment options have been made for the input.
TERMINAL SETTING
DVI MODE
Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC” when
PC or other computer equipment is connected. Select “DVI-HD” when DVD player, which has
DVI-D output, is connected.
DVI-PC
RGB
D-SUB MODE
Selects the type of signal associated with the D-SUB input.
RGB: Analog input (R, G, B, H, V)
COMPONENT: Component (Y, Cb/Pb, Cr/Pr)
SCART: SCART signal
VIDEO: Composite video (VIDEO2)
S-VIDEO:
HDMI SIGNAL
DEINTERLACE
RAW: Disable the expanded feature.
EXPAND: Expand image contrast and increase detail in the dark and bright areas.
EXPAND
ON
Selects the IP (Interlace to Progressive) conversion function.
Note: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu.
ON
Converts interlaced signals to progressive. This is the default setting.
OFF
Disables IP conversion. This setting is best suited for motion pictures, but increases the risk of
image retention.
COLOR SYSTEM
The selected Color System depends on the video format of the input signal.
Automatically chooses Color System setting based on input signal.
AUTO
VIDEO1, VIDEO2, S-VIDEO inputs only
AUTO
NTSC
PAL
SECAM
4.43 NTSC
PAL-60
English-25
Download from Www.Somanuals.com. All Manuals Search And Download.
OVER SCAN
Some video formats may require different scanning modes in order to best display the image.
ON
HDMI, DVD/HD, SCART, VIDEO1, VIDEO2,
S-VIDEO inputs only
ON
Image size is larger than what can be displayed. The image edge will appear cropped.
Approximately 95% of the image will be shown on the screen.
OFF
Image size stays within the display area. The whole image is displayed on the screen.
NOTE: When you use a computer with HDMI out, please set “OFF”.
OPTION SETTING
OPTION POWER
You can set this setting when option board accessory is connected to the monitor.
Please contact your supplier for detailed information about Option board slot accessories.
-
Allow the monitor to supply power to Option board slot during power save mode or standby
mode.
OFF
AUDIO
(not adjustable)
INTERNAL PC
OFF WARNING
The function is available for slot 2 type PC.
If OPTION POWER is OFF, a warning message appears when monitor power is turned off.
Note: Warning message does not appear when monitor power is turned off by OFF TIMER
setting or SCHEDULE setting.
AUTO OFF
Monitor power is automatically “OFF” when connected PC is OFF or the monitor is in power save
mode.
START UP PC
FORCE QUIT
When ON is selected, connected PC start-up.
When ON is selected, it performs force-quit PC.
120Hz
(not adjustable)
TOUCH PANEL
RESET
-
-
-
(not adjustable)
Resets the following settings within the ADVANCED OPTION menu back to factory setting:
INPUT DETECT (except the priority of input signals), INPUT CHANGE, TERMINAL SETTING,
DEINTERLACE, COLOR SYSTEM, OVER SCAN, START UP PC in OPTION SETTING and
FORCE QUIT in OPTION SETTING.
FACTORY RESET
Resets OSD options back to factory settings EXCEPT FOR: PICTURE MODE, VOLUME,
SCHEDULE SETTINGS, DATE & TIME, ASPECT in PIP, SUB INPUT in PIP, LANGUAGE,
LAN SETTING, TILE MATRIX MEM, OSD ROTATION, CHANGE SECURITY PASSWORD and
SECURITY.
-
English-26
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE 1: CREATING A SCHEDULE
The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be programmed.
To program the schedule:
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the
Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule can now be
programmed.
2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down buttons to
highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.
3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to highlight
PIC. MODE. Use the + and - buttons to choose the picture mode.
4. Use the down button to select a day on which the schedule will be enabled. Push the set
button to enable. If the schedule is to be ran every day, choose EVERY DAY and press
the SET button. The circle next to EVERY DAY will turn yellow. If a weekly schedule is
desired, choose the days of the week using the up and down buttons and pressing SET
to select. Then highlight the EVERY WEEK option and press SET.
DVI
SCHEDULE:
OFF TIMER
(THU) JUN.18.2009 15:38
SETTINGS:
1
2
3
4
5
6
7
SCHEDULE SETTINGS
SCHEDULE LIST
DATE & TIME
RESET
ON:
– – : – –
– – : – –
– – – –
– – – –
OFF:
INPUT:
5. After a schedule is programmed the remaining schedules can then be set. Press MENU
to leave the OSD or press EXIT to go back to the previous menu.
PIC. MODE:
EVERY DAY
EVERY WEEK
Note: If schedules are overlapping then the schedule with the highest number will have
priority over the schedule with the lowest number. For example schedule #7 will have
priority over schedule #1.
MON
TUE
FRI
WED
SAT
THU
SUN
Return
Close
Choose
Mark
If selected input or picture mode is not available now, disable input or picture mode
is shown in red.
NOTE 2: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen saver at
regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.
For long life use as Public Display
Image Sticking of LCD Panel
When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual or
“ghost” image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along the
displayed image, and may be permanent. (Image Sticking)
Recommendations
To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.
1. Fixed image should not be displayed for long period. Change fixed images after short intervals.
2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.
3. Lower environmental temperatures prolong the lifespan of the monitor.
When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor are
stacked, utilize the temperature sensors inside monitor.
To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.
4. Please use “Screen Saver Mode” of monitor.
English-27
Download from Www.Somanuals.com. All Manuals Search And Download.
Remote Control Function
REMOTE CONTROL ID FUNCTION
Monitor ID:1
Monitor ID:2
Monitor ID:3
REMOTE CONTROL ID
The remote control can be used to control up to 100 individual MultiSync monitors using
what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode
works in conjunction with the Monitor ID, allowing control of up to 100 individual MultiSync
monitors. For example: if there are many monitors being used in the same area, a remote
control in normal mode would send signals to every monitor at the same time (see
Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate one specific
monitor within the group (see Figure 2).
Remote works
Remote works
Remote works
Figure 1
Remote in
Normal mode or
the REMOTE ID
is set to 0
TO SET REMOTE CONTROL ID
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD to
input the Monitor ID (1-100) of the display to be controlled via remote. The remote can then
be used to operate the monitor having that specific Monitor ID number.
When 0 is selected or when the remote control is in normal mode, all monitors will be
operated.
Monitor ID:1
Monitor ID:2
Monitor ID:3
TO SET/RESET REMOTE CONTROL MODE
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for
2 seconds.
Remote does
not work
Remote does
not work
Remote works
Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold
down for 2 seconds.
In order for this feature to work properly, the display must be assigned a Monitor ID number.
The Monitor ID number can be assigned under the MULTI DISPLAY menu in the OSD
(See page 23).
Figure 2
Remote set up
to use REMOTE
ID:3
Point the remote control towards the remote sensor of the desired monitor and press the
REMOTE ID SET button. The MONITOR ID number is shown on the display when your
remote control is in ID mode.
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.
1. Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100.
This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.
2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID number
(1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to simultaneously
control all displays in range.
3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.
The MONITOR ID number is shown in red on the display.
If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.
If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.
This LCD monitor can be controlled via personal computer or wireless remote control using an RS-232C connection.
MONITOR ID and IR CONTROL
Using one PC or one infrared wireless controller, up to 100 individual LCD monitors can be controlled through a daisy chain via RS-232C
connection.
1. Connect PC and LCD monitors.
Connect a PC’s RS-232C control output to the LCD monitor RS-232C input. You can then connect the RS-232C output from the LCD monitor
to another LCD monitor RS-232C input. Up to 100 monitors can be connected using RS-232C.
2. Set Monitor ID and IR Control mode.
For proper operation, the Monitor ID should be set in the OSD menu of each monitor that is in the chain. The Monitor ID can be set under the
“MULTI DISPLAY” menu in the OSD. The Monitor ID number can be set within a range from 1 to 100. No two monitors should share the same
Monitor ID number. It is recommended to number each monitor in a daisy chain sequentially from 1. The first monitor in the daisy chain is
designated as the primary monitor. Subsequent monitors with the chain are secondary monitors.
In the “ADVANCED OPTION” menu on the first monitor in the RS-232C daisy chain set the “IR CONTROL” to “PRIMARY”.
Set the “IR CONTROL” to “SECONDARY” on all other monitors.
English-28
Download from Www.Somanuals.com. All Manuals Search And Download.
3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor.The Information OSD will be shown at
top left side of the screen.
Monitor ID: Displays the ID number of the current monitor within the daisy chain.
Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor.
Press the “+” or “-” buttons to change the “Target ID” to show the ID number of the monitor to be controlled. To control the entire daisy chained
monitors simultaneously, select “ALL” as the “Target ID.”
4. Use the wireless remote controller to control the “SECONDARY” monitor while aiming at the “PRIMARY” monitor.
The “MENU OSD” will appear on the selected target monitor.
NOTE: If the “ID No.” mode select OSD is showing, press the “DISPLAY” button on the remote control while pointing at the “PRIMARY”
monitor to clear this OSD.
HINT:
If you lost control due to the incorrect setting of “IR CONTROL”, pressing the “DISPLAY” button on the remote control for 5 or
more seconds will reset the “IR CONTROL” menu to “NORMAL” function.
WIRED REMOTE CONTROL FUNCTION
You can control this monitor by connecting REMOTE IN/OUT with Stereo Mini plug cable (3.5 ).
MultiSync
MultiSync
OUT
IN
Remote IN
Remote OUT
Remote IN
Remote OUT
MultiSync
Remote control cable
Remote control cable
NOTE: Turn off the main power switch before connect/disconnect Stereo Mini plug cable.
NOTE: Do not use this connector unless specified.
English-29
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the LCD monitor via RS-232C Remote Control
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.
NOTE:
When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 23).
Functions that can be controlled by a personal computer are:
•
•
Power ON or OFF
Switching between input signals
Connection
LCD Monitor + PC
MultiSync
MultiSync
OUT
IN
PC
RS-232C (IN)
RS-232C (OUT)
RS-232C (IN)
RS-232C (OUT)
(Out)
RS-232C Cable
RS-232C Cable
MultiSync
NOTE:
If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your
dealer for details.
Check the “ID=ALL REPLY” setting in “EXTERNAL CONTROL”.
* In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model.
Do not connect to other types of equipment.
To control monitor or multiple monitors that are daisy-chained together please use the control command. Instructions for the
control command can be found on the CD included with the display. The file is called “External_control.pdf”.
Multiple monitors that are daisy-chained have a limit to the conectable monitor.
1) Interface
PROTOCOL
BAUD RATE
DATA LENGTH
PARITY BIT
STOP BIT
RS-232C
9600 [bps]
8 [bits]
NONE
1 [bit]
FLOW CONTROL NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
The reverse type cable (null modem cable) (not include) should be used for RS-232C control.
English-30
Download from Www.Somanuals.com. All Manuals Search And Download.
2) Control command diagram
For other commands, please see “External_Control.pdf” file on the CD-ROM.
Function (Monitor ID = 1)
Code Data
Power ON
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 31 03 73 0d
01 30 41 30 41 30 43 02 43 32 30 33 44 36 30 30 30 34 03 76 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 46 03 04 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 33 03 71 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 31 03 73 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 31 31 03 72 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 43 03 01 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 35 03 77 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 37 03 75 0d
01 30 41 30 45 30 41 02 30 30 36 30 30 30 30 44 03 06 0d
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 31 03 09 0d
01 30 41 30 45 30 41 02 30 30 38 44 30 30 30 32 03 0a 0d
Power OFF
Input Source Select DisplayPort
Input Source Select DVI
Input Source Select VGA
Input Source Select HDMI
Input Source Select DVD/HD
Input Source Select VIDEO
Input Source Select S-VIDEO
Input Source Select OPTION
Sound Mute ON
Sound Mute OFF
English-31
Download from Www.Somanuals.com. All Manuals Search And Download.
Controlling the LCD monitor via LAN Control
Connecting to a Network
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.
NOTE:
When you use this function, EXTERNAL CONTROL should be “LAN” (See page 23).
To use a LAN connection, you are required to assign an IP address.
Example of LAN connection:
Server
NOTE: Use a category 5 or higher LAN cable.
Hub
LAN cable
(not supplied)
Network Setting by Using an HTTP Browser
Overview
Connecting the monitor to a network allows for monitor control from a computer via the network.
To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.
The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an HTTP
server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher version for the web browser.
(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will
vary depending on the version of browser. Please refer to the help files and the other information provided in your software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the
monitor and entering the following URL.
Network Setting
TIP:
The default IP address is “192.168.0.10”.
The exclusive application can be downloaded from our website.
NOTE:
If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to
refresh your web browser (or clear the cache).
The display or button’s response can be slowed down or operation may not be accepted depending the settings of
your network. Should this happen, consult your network administrator.
The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a
moment and repeat. If you still can’t get a response, turn the monitor off and then back on.
English-32
Download from Www.Somanuals.com. All Manuals Search And Download.
Preparation Before Use
Connect the monitor to a commercially available LAN cable before engaging in browser operations.
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting
method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be
displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in operation.
It is recommended that a proxy server not be used unless it is unavailable.
Handling of the Address for Operation via a Browser
The host name can be used under the following cases:
If the host name corresponding to the IP address of the monitor has been registered to the domain name server (DNS) by the
network administrator, you can then access the network settings of the display via that registered host name using a compatible
browser.
If the host name corresponding to the IP address of the monitor has been configured in the “HOSTS” file of the computer being
used, you can then access the network settings of the display via that host name using a compatible browser.
Example 1: When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by
Example 2: When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying
http://192.168.73.1/index.html for the address or the entry column of the URL.
Network Settings
DHCP
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from your
network administrator.
NOTE: Consult your network administrator for the IP address when [ENABLE] is selected for
[DHCP].
IP v4 Address
Subnet Mask
Set your IP address of the network connected to the monitor when [DISABLE] is selected for [DHCP].
Set your subnet mask number of the network connected to the monitor when [DISABLE] is selected
for [DHCP].
Default Gateway
Set your default gateway of the network connected to the monitor when [DISABLE] is selected for
[DHCP].
Primary DNS
Secondary DNS
Apply
Set your primary DNS settings of the network connected to the monitor.
Set your secondary DNS settings of the network connected to the monitor.
Reflect your settings.
NOTE: Make sure to execute “the reboot” from the “reboot screen” or to turn the monitor off and
then back on to enable the changing, after clicking [Apply].
NOTE:
The following settings will reset back to the factory setting when “LAN reset” is selected by an EXTERNAL CONTROL
of OSD:
[DHCP]: DISABLE, [IP v4 Address]: 192.168.0.10, [Subnet Mask]: 255.255.255.0, [Default Gateway]: 192.168.0.1 but
[Primary DNS] and [Secondary DNS] are not changed.
English-33
Download from Www.Somanuals.com. All Manuals Search And Download.
Alert Mail Setting
This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be
sent when an error occurs in the monitor.
Alert Mail
Checking [ENABLE] will turn on the Alert Mail feature.
Checking [DISABLE] will turn off the Alert Mail feature.
Host Name
Domain Name
Type in the hostname of the network connected to the monitor.
Up to 60 alphanumeric characters can be used.
Type in the domain name of the network connected to the monitor.
Up to 60 alphanumeric characters can be used.
Sender’s Address
SMTP Server
Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.
Type in the SMTP server name to be connected to the monitor.
Up to 60 alphanumeric characters can be used.
Recipient’s Address
1 to 3
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
Authentication Method
POP3 Server
This selects the authentication method of the e-mail transmission.
This specifies the address of the POP3 server that is used in the authentication of the e-mail.
User Name
This sets the user name for logging into the authentication server when authentication is required
for the e-mail transmission. Up to 60 alphanumeric characters can be used.
Password
This sets the password for logging into the authentication server when authentication is required for
the e-mail transmission. Up to 60 alphanumeric characters can be used.
TestMail
Apply
Click this button to send a test mail to check if your settings are correct.
Click this button to reflect the above settings.
NOTE: Make sure to execute “the reboot” from the “reboot screen” or to turn the monitor off and
then back on to enable the changing, after clicking [Apply].
NOTE:
TIP:
• If you execute a test, you may not receive an Alert mail.
Should this happen, check if the network settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert mail.
Should this happen, check if the Recipient’s Address is correct.
The Alert Mail settings will not be affected even when [RESET] is done from the menu.
For Control command diagram, please see file “External_Control.pdf” on the CD-ROM.
English-34
Download from Www.Somanuals.com. All Manuals Search And Download.
Alert error message list
Error number
* ErrorCode
Alert mail Message
Explanation
Measure
The monitor’s power supply is not
functioning normally.
Standby power Abnormal
Please contact your supplier.
70h ~ 7Fh
80h ~ Fh
The cooling fan has stopped.
Cooling fan Abnormal
Backlight abnormal
Please contact your supplier.
Please contact your supplier.
The monitor’s back light unit is not
functioning normally.
90h ~ 9Fh
A0h ~ AFh
The monitor is overheated.
Temperature Abnormal
Please contact your supplier.
SENSOR reached at the temperature
that the user had specified.
Reconfirm the setting condition from
OSD (DISPLAY PROTECTION-FAN
CONTROL) or please contact your
supplier.
A2h
*condition: DISPLAY PROTECTION-FAN
CONTROL-COOLING FAN = AUTO
The monitor doesn’t have the input
signal.
No signal
Please check “No picture” in
“Troubleshooting”.
B0h ~ BFh
C0h ~ CFh
The monitor caused the problem of the Option board abnormal
abnormal of option board.
Please contact your supplier.
Sample: The following examples are content of Alert Mail that informs the temperature anomaly of monitor.
Sample: The following examples are content of test mail by browser.
English-35
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
Reduced Footprint: Provides the ideal solution for environments with superior image quality.
Color Control Systems: Allow you to adjust the colors on your screen and customize the color accuracy of your monitor to a
variety of standards.
OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six
axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides
the monitor with a uniform color profile. This assures that the colors displayed on the monitor are exactly the same as on the
color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen
and customise the color accuracy of your monitor to a variety of standards.
sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays and
other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation and
backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to use
on-screen menus.
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing
the monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically
optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions and
lowering the air conditioning costs of the workplace.
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.
VESA Standard (FDMIv1) Mounting Interface: Allows you to connect your LCD monitor to any VESA standard (FDMIv1) third
party mounting arm or bracket. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard
in North America.
DVI-D: The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between
computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based
digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital
connectors such as DFP and P&D. The DVI interface of this display supports HDCP.
TILE MATRIX,TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.
ZOOM: Expands image size for horizontal and vertical direction.
RS-232C daisy chain: You can control the multiple monitors by controller or wireless remote controller.
Self-diagnosis: If an internal error should occur, a failure state will be indicated.
HDCP (High-bandwidth Digital Content Protection): HDCP is a system for preventing illegal copying of video data sent over
a Digital Visual Interface (DVI). If you are unable to view material via the DVI input, this does not necessarily mean the display is
not functioning properly. With the implementation of HDCP, there may be cases in which certain content is protected with HDCP
and might not be displayed due to the decision/intention of the HDCP community (Digital Content Protection, LLC).
Option board slot: You can use an option board. Please contact your supplier for detailed information.
English-36
Download from Www.Somanuals.com. All Manuals Search And Download.
Troubleshooting
RED LED on monitor is blinking
No picture
•
A certain failure might have occurred, please contact your
nearest authorized NEC DISPLAY SOLUTIONS service
facility.
•
The signal cable should be completely connected to the
display card/computer.
•
•
The display card should be completely seated in its slot.
•
If the monitor is powered off by the inside temperature
being higher than the normal operating temperature, a RED
LED will blink six times. Power on the display again after
confirming the inside temperature has been reduced to
normal operation temperature.
Check the main Power Switch, it should be in the ON
position.
•
•
Front Power Switch and computer power switch should be in
the ON position.
Check to make sure that a supported mode has been
selected on the display card or system being used. (Please
consult display card or system manual to change graphics
mode.)
Display image is not sized properly
•
Use the OSD Image Adjust controls to increase or decrease
the coarse adjustment.
•
Check to make sure that a supported mode has been
selected on the display card or system being used.
(Please consult display card or system manual to change
graphics mode.)
•
•
Check the monitor and your display card with respect to
compatibility and recommended settings.
Check the signal cable connector for bent or pushed-in pins.
Power Button does not respond
Selected resolution is not displayed properly
•
Unplug the power cord of the monitor from the AC outlet to
turn off and reset the monitor.
•
Use OSD Display Mode to enter Information menu and
confirm that the appropriate resolution has been selected. If
not, select corresponding option.
•
Check the main Power Switch on the back side of the
monitor.
No Sound
Image persistence
•
•
•
•
Check to see if audio cable is properly connected.
•
Please be aware that LCD Technology may experience
a phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of a
previous image remains visible on the screen. Unlike CRT
monitors, LCD monitors’ image persistence is not permanent,
but constant images being displayed for a long period of time
should be avoided. To alleviate image persistence, turn off
the monitor for as long as the previous image was displayed.
For example, if an image was on the monitor for one hour
and a residual image remains, the monitor should be turned
off for one hour to erase the image.
Check to see if mute is activated.
Check to see if volume is set at minimum.
Check to see if computer supports an audio signal through
DisplayPort.
If unsure, contact the computer manufacturer.
•
•
Check to see if SURROUND is ON.
Check Internal/External speaker switch.
Remote Control is not available
•
•
•
Check the Remote Control’s batteries status.
Check if batteries are inserted correctly.
NOTE:
As with all personal display devices, NEC DISPLAY
SOLUTIONS recommends displaying moving images
and using a moving screen saver at regular intervals
whenever the screen is idle or turning off the monitor
when not in use.
Check if the Remote Control is pointing at the monitor’s
remote sensor.
•
•
Check the Remote Control Mode status.
The remote control system may not function when direct
sunlight or strong illumination strikes the remote control
sensor of the LCD monitor, or when there is an object in the
path.
Image is unstable, unfocused or swimming is apparent
•
Signal cable should be completely attached to the computer.
•
Use the OSD Image Adjust controls to focus and adjust
display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSD Image Adjust
settings may need to be re-adjusted.
“SCHEDULE”/“OFF TIMER” function is not working properly
•
The “SCHEDULE” function will be disabled when the “OFF
TIMER” is set.
•
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
•
If the “OFF TIMER” function is enabled and the power to
the LCD monitor is turned off when the power supply is
interrupted unexpectedly, then the “OFF TIMER” will be reset.
If your text is garbled, change the video mode to non-
interlace and use 60Hz refresh rate.
Snowy Picture, Poor Sound in TV
•
Check antenna/cable connection. Use new cable if
necessary.
Image of component signal is greenish
Check to see if the DVD/HD input connector is selected.
•
Interference in TV
LED on monitor is not lit
•
Check components for shielding, move away from monitor if
necessary.
(no green or red color can be seen)
•
•
•
•
Power Switch should be in the ON position and power cord
should be connected.
RS-232C or LAN control is not available
Check the main Power Switch, it should be in the ON
position.
•
•
•
Check RS-232C or LAN cable connection.
Check “CONTROL” setting in “EXTERNAL CONTROL”.
Make certain the computer is not in a power-saving mode
(touch the keyboard or mouse).
Check the “ID=ALL REPLY” setting in “EXTERNAL
CONTROL”.
Check to see that the power indicator option in the OSD is
set to ON.
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or degradation.
English-37
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Product Specifications
LCD Module
31.5”/800.4 mm diagonal
Pixel Pitch: 0.510 mm
Resolution: 1366 x 768
Color: Over 16 million colors (depending on video card used)
Brightness: 450 cd/m2 (Max.), 340 cd/m2 (Factory setting Typ.) @25°C
Contrast Ratio: 3000:1
Viewing Angle: 89° (typ) @ CR>10
Frequency
Horizontal: 15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)
31.5 kHz - 91.1 kHz (Digital Input)
Vertical: 50.0 - 85.0 Hz
Pixel Clock
25.2 MHz - 162.0 MHz
697.7 x 392.3 mm
Viewable Size
Input Signal
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60*1, UXGA60*1, 1920X1080*1 (60Hz), 1080p*1,
1080i*1
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.1a, applicable to HDCP V1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60*1, UXGA60*1, 1920x1080*1 (60 Hz), 1080p*1,
1080i*1, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
VGA*2
HDMI
15pin Mini D-sub
HDMI Connector
Analog RGB
Sync
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60*1, UXGA60*1, 1920X1080*1 (60Hz)
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
Digital YUV
Digital RGB
HDMI
VGA60, SVGA60, XGA60, WXGA60, SXGA60*1, UXGA60*1, 1920x1080*1 (60 Hz), 1080p*1,
1080i*1, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
DVD/HD*2 15pin Mini D-sub
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p*1, 1080i*1, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz,
480i@60Hz
VIDEO1
BNC
15pin Mini D-sub
Composite
S-VIDEO
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
VIDEO2*2
S-VIDEO*2 15pin Mini D-sub
Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
Output Signal
DVI
DVI-D 24pin
Digital RGB
DVI (HDCP)
AUDIO
AUDIO
Input
STEREO Mini Jack
HDMI Connector
Analog Audio
Digital Audio
Stereo L/R 0.5 Vrms
PCM 32, 44.1, 48 KHz (16/20/24bit)
PCM 32, 44.1, 48 KHz (16/20/24bit)
Stereo L/R 0.5 Vrms
DisplayPort Connector Digital Audio
RCA (L/R) Analog Audio
AUDIO
Output
Speaker Output
Control
Internal Speaker 8 W + 8 W
RS-232C In: 9 Pin D-sub
RS-232C Out: 9 Pin D-sub (with daisy chain)
LAN: RJ-45 10/100 BASE-T
Remote IN: Stereo Mini jack 3.5
Remote OUT: Stereo Mini jack 3.5
Power Supply
2.0 - 0.8 A @ 100-240V AC, 50/60Hz
Operational Environment
Temperature: 5 - 40°C / 41 - 104°F, 5 - 35°C / 41 - 95°F (in portrait orientation with Slot 2 type PC*3)
Humidity: 20 - 80% (without condensation)
Altitude: 0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature: -20 - 60°C / -4 - 140°F
Humidity: 10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
786.8 (W) x 476.2 (H) x 93.5 (D) mm / 31.0 (W) x 18.7 (H) x 3.7 (D) inches
Weight
12.4 kg (27.3 lbs)
VESA compatible mounting interface
Power Management
Plug & Play
200 mm x 200 mm (M6, 4 Holes)
VESA DPM
VESA DDC2B, DDC/CI, DisplayPort
Accessories
Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, CD-ROM
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image.
*2: Common terminal.
*3: Please ask your NEC sales representative for detailed information.
English-38
Download from Www.Somanuals.com. All Manuals Search And Download.
Pin Assignment
1) Analog multi input (MiniDsub15p): VGA, DVD/HD, SCART, VIDEO2, S-VIDEO
Pin No Name
1
2
Red, DVD/HD_Pr, S-VIDEO_C
Green, DVD/HD_Y, S-VIDEO_Y, VIDEO2
3
Blue, DVD/HD_Pb
GND
4
Mini D-SUB 15P
5
DDC-GND
Red-GND
Green-GND
Blue-GND
+5V (DDC)
SYNC-GND
GND (B-SYNC)
DDC-SDA
1
5
6
6
7
10
15
11
8
9
10
11
12
13
14
15
H-SYNC
V-SYNC
DDC-SCL
2) RS-232C input/output
Pin No Name
1
2
3
4
5
6
7
8
9
NC
D-SUB 9P
RXD
TXD
NC
5
1
6
GND
NC
9
NC
NC
NC
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
3) REMOTE IN
4) REMOTE OUT
English-39
Download from Www.Somanuals.com. All Manuals Search And Download.
Manufacturer’s Recycling and Energy Information
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s top
priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentally-friendly
products, and always strive to help define and comply with the latest independent standards from agencies such as ISO
(International Organisation for Standardization) and TCO (Swedish Trades Union).
Disposing of your old NEC product
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling procedures
and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end of its life.
All required information concerning the disposal of the product and country-specific information on recycling facilities can be
found on our following websites:
http://www.nec-display-solutions.com/greencompany/ (in Europe),
http://www.nec-display.com (in Japan) or
http://www.necdisplay.com (in USA).
Energy Saving
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.
Mode
Power consumption
Approx. 88 W
LED colour
Green
Normal Operation*1
Energy Saving Mode*1, *2
Power Off
Less than 1 W
Amber
Red
Less than 0.5 W
*1: without any option, with factory settings.
*2: VGA input only.
WEEE Mark (European Directive 2002/96/EC)
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This includes
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your
NEC display products, please follow the guidance of your local authority, or ask the shop where you purchased
the product, or if applicable, follow any agreements made between yourself and NEC.
The mark on electrical and electronic products only applies to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority
so as to comply with the correct disposal method.
English-40
Download from Www.Somanuals.com. All Manuals Search And Download.
|