Instructions for use
Thank you for purchasing the Musical Fidelity M6PRX CRPS dual mono power amplifier.
The M6PRX is designed to be partnered with present and future M6 series products. It features twin
conservatively rated power amplifier sections connected in dual mono configuration for the absolute best in
stereo imaging and drive capabilities. Two independent and over-specified choke regulated power supplies also
ensure the absolute best in supply noise filtering, separation and power reserve possible in a single box power
amplifier. This combination yields one of the best high-fidelity systems available at any price.
Used properly and carefully, it should give many years of outstanding musical reproduction.
Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing agents - they may
harm the surface finish.
If there are any questions about the audio system, please consult the dealer who is there to help and advise.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
IMPORTANT! (U.K. only)
This unit is supplied in the U.K. with mains lead fitted with a moulded 13 amp plug. If, for any reason, it is
necessary to remove the plug, please remove the fuse holder and dispose of the plug safely, out of reach of
children.
It must not be plugged into a mains outlet.
The wires in the mains lead supplied with this appliance are coloured in accordance with the following code:
Green and yellow .............................Earth
Blue................................................ Neutral
Brown ..................................................Live
WARNING – This appliance MUST be earthed
As the colours of the wires of the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in the plug, proceed as follows:
•
•
•
•
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked
with the letter E or coloured green or green-and-yellow, or by the earth symbol:
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
If connecting to a BS1363 plug, a 13 amp fuse must be used.
WARNING:
ANY MODIFICATIONS TO THIS PRODUCT NOT EXPRESSLY
APPROVED BY MUSICAL FIDELITY WHO IS THE PARTY RESPONSIBLE
FOR STANDARDS COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THIS EQUIPMENT.
Issue 2
Page 3 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL ADVICE
Installation, Precautions & User Information
This new M6PRX is designed and built to provide trouble-free performance, but as with all electronic devices it
is necessary to observe a few precautions:
•
•
•
Heed all warnings shown on the back of the product.
Only connect the M6PRX to a mains outlet having the same voltage as marked at the back of the unit.
Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is
switched off.
•
•
Position the mains lead and signal interconnects where they are not likely to be walked on or trapped by
items placed on them.
Do not use near water, or place water-filled containers on the M6PRX, for example, a flower vase or potted
plants. If water does spill inside, immediately pull out the mains plug from the wall socket and inform
your dealer, who should then check the unit before further use. Entry of liquid into the M6PRX is
dangerous, and may cause electric shock or fire hazard.
•
•
Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.
Do not remove any covers or try to gain access to the inside. There are no internal adjustments or fuses you
can replace yourself. Refer all service work to an authorised Musical Fidelity agent.
* Note: Unauthorised opening of the equipment will invalidate any warranty claim.
•
Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents - they
may harm the surface finish.
The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected or damaged by
lightning. For protection of the audio system during electrical storms, remove the mains plugs.
If after-sales service is required, to help the dealer identify the M6PRX please quote the serial number located
on the rear panel of the unit.
Issue 2
Page 4 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM DISPOSAL INFORMATION
DISPOSAL
The crossed out wheeled bin label that appears on the back panel of the product indicates that
the product must not be disposed of as normal household waste. To prevent possible harm to the
environment please separate the product from other waste to ensure that it can be recycled in an
environmentally safe manner. Please contact local government office or retailer for available collection
facilities.
DISPOSITION
La poubelle sur roulettes barrées X, qui apparaît en logo sur le panneau arrière du produit, indique que celui-ci ne
doit pas être traité comme un déchet domestique commun. Afin de protéger l'environnement, ce produit électronique devra
être géré séparément et donc recyclé selon les nouvelles normes Européennes Rohs concernant les déchets d'appareils
électroniques. Prière de contacter les services concernés gouvernementaux ou votre point de vente pour l'élimination et
l'enlèvement de déchets électroniques équipés de composants électroniques.
DISPOSAL
La etiqueta cruzada hacia fuera del compartimiento que aparece en el panel trasero del producto indica que el
producto no se debe reciclarse como basura normal de la casa. Para prevenir daños posible al ambiente separe por favor el
producto de otras basura para asegurarse de que puede ser reciclada de una manera ambientalmente segura. Entre en
contacto por favor a su oficina gubernamental local o a su minorista para las instalaciones disponibles de la colección.
RIFIUTI
L'etichetta del cassonetto barrato riportato sul retro dell'apparecchio indica che il prodotto non deve essere
smaltito tramite la procedura normale di smaltimento dei rifiuti domestici. Per evitare eventuali danni all'ambiente, separare
questo prodotto da altri rifiuti domestici in modo che possa venire riciclato in base alle procedure di rispetto ambientale. Per
maggiori dettagli sulle aree di raccolta disponibili, contattate l'ufficio govenativo locale od il rivenditore del prodotto.
FACHGERECHTE ENTSORGUNG:
Das auf der Geräterückseite angebrachte Label deutet darauf hin, dass das Produkt nicht mit konventionellem
Hauskehricht entsorgt werden darf. Um Schäden und Verschmutzungen an Umwelt und Mensch zu vermeiden, muss das
Produkt fachgerecht entsorgt und von anderem Abfall getrennt werden. Wenden Sie sich bei Fragen hierzu an Ihren
Fachhändler oder an eine öffentliche Informationsstelle.
AFVAL
Het label op de achterzijde van dit apparaat, een afvalbak op wielen met een kruis doorgehaald, geeft aan dat dit
apparaat niet samen met gewoon huishoudafval mag worden weggegooid. Om mogelijke schade aan onze leefomgeving te
voorkomen dient dit apparaat, gescheiden van gewoon huishoudelijk afval, te worden afgevoerd zodat het op een
milieuvriendelijke manier kan worden gerecycled. Neem voor beschikbare inzamelplaatsen contact op met uw gemeentelijke
reinigingsdienst of met uw elektronica leverancier.
HÄVITTÄMINEN
Yliruksattua jäteastiaa kuvaava tarra tuotteen takalevyssä kertoo, että tuotetta ei saa käsitellä normaalina
talousjätteenä. Ympäristön suojelemiseksi on tuote pidettävä erillään muusta jätteestä ja se on kierrätettävä ekologisesti
kestävällä tavalla. Ota yhteyttä laitteen myyjään tai Pirkanmaan Ympäristökeskukseen lähimmän kierrätyskeskuksen
löytämiseksi.
AFSKAFNING
Logoet med en skraldespand med kryds over på bagsiden af apparatet indikerer at dette produkt ikke må kasseres
som normal husholdningsaffald. For at forebygge mulig skade på miljøet, bedes De separere dette produkt fra andet affald,
og sikre at det bliver genbrugt på en miljørigtig måde. Kontakt venligst de lokale myndigheder eller din forhandler for
oplysning om nærmeste tilgængelige opsamlingssted for elektronikaffald.
ΔΙΑΔΙΚΑΣΙΑ ΑΠΟΡΡΙΨΗΣ
ΤΟ ΣΗΜΑ ΜΕ ΤΟΝ ΔΙΑΓΕΓΡΑΜΜΕΝΟ ΤΡΟΧΗΛΑΤΟ ΚΑΔΟ ΑΠΟΡΡΙΜΑΤΩΝ ΣΤΗΝ ΠΙΣΩ ΟΨΗ ΤΟΥ
ΜΗΧΑΝΗΜΑΤΟΣ
ΔΗΛΩΝΕΙ ΟΤΙ ΤΟ ΠΡΟΙΟΝ ΑΥΤΟ ΔΕΝ ΠΡΕΠΕΙ ΝΑ ΔΙΑΧΕΙΡΙΣΘΕΙ ΣΑΝ ΣΥΝΗΘΙΣΜΕΝΟ ΟΙΚΙΑΚΟ ΑΠΟΒΛΗΤΟ.
ΠΡΟΣ ΑΠΟΦΥΓΗ ΕΝΔΕΧΟΜΕΝΗΣ ΕΠΙΒΑΡΥΝΣΗΣ ΤΟΥ ΠΕΡΙΒΑΛΛΟΝΤΟΣ, ΞΕΧΩΡΙΣΤΕ ΤΟ ΠΡΟΙΟΝ ΑΠΟ ΤΑ ΑΛΛΑ
ΑΠΟΡΡΙΜΑΤΑ ΩΣΤΕ ΝΑ ΕΞΑΣΦΑΛΙΣΘΕΙ Η ΑΝΑΚΥΚΛΩΣΗ ΤΟΥ ΜΕ ΤΟΝ ΠΡΕΠΟΝΤΑ ΤΡΟΠΟ.
ΠΑΡΑΚΑΛΟΥΜΕ ΝΑ ΕΠΙΚΟΙΝΩΝΗΣΕΤΕ ΜΕ ΤΗΝ ΤΟΠΙΚΗ ΥΠΗΡΕΣΙΑ ΑΝΑΚΥΚΛΩΣΗΣ Η ΜΕ ΤΟ ΚΑΤΑΣΤΗΜΑ ΑΓΟΡΑΣ
ΓΙΑ ΠΕΡΙΣΣΟΤΕΡΕΣ ΛΕΠΤΟΜΕΡΕΙΕΣ.
Issue 2
Page 5 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Introduction
Congratulations on the purchase of the new M6PRX power amplifier. Great attention has been paid to internal
layout, isolating each circuit section to prevent possible interaction.
The unit features two monoblock amplifiers with separate choke regulated supplies for the absolute best in
separation and imaging. Generously rated, they are enough to drive even the most demanding loudspeakers
with ease. Low distortion and very quiet they will deliver all music types exactly as the artist originally intended.
The resultant performance achieved by this unit is among the best in the world. It has excellent signal to noise
ratio, low distortion, wide bandwidth and dynamic range, with extraordinary resolution and fine detail.
Cleaning
Before cleaning the unit, switch off power at the mains switch and remove the mains plug from the wall socket.
Clean the cabinet and remote control unit using a moist cloth. Using solvents, white spirit or thinners is not
advised, as they could damage the surface finish.
Installation
Position the M6PRX on a stable, horizontal surface where there is no risk of it being knocked, or subjected to
vibration such as from loudspeakers.
Important note:
In normal operation, the unit dissipates a small quantity of power at all times, and it is important
that it is adequately ventilated. The top and bottom are perforated to allow the smooth flow of heat
through the unit. It is therefore not recommended that the unit is enclosed in a cabinet or placed
where the ventilation holes are impeded as this could result in excessive heat build-up.
The M6PRX must be protected from humidity – if the unit is moved from a cold place to a warm
room, leave the unit for an hour or so to allow sufficient time for the moisture to evaporate.
Power Connections
The M6PRX is supplied with a standard IEC mains cable which plugs into the IEC socket at the back of the unit
(see page 7)
Audio Connections
RCA Inputs: Connect all RCA single-ended sources to relevant analogue inputs (see page 7 for more
information). Use good quality fully connected (signal and ground) coaxial phono cables for all RCA signal
connections. 2 inputs INPUT A and INPUT B are provided to enable the amplifier to be used with more than
one setup for example, A = home theatre, B = audio only.
XLR Inputs: Connect any XLR balanced source to balanced analogue input (see page 7 for more information).
Use good quality fully connected (signals and ground) balanced XLR cables for all XLR signal connections.
Outputs: Connect loudspeakers to the terminals on the back panel marked as LEFT and RIGHT SPEAKER
outputs
The LOOP OUT output allows the input signals to be passed on to a second amplifier or other component. This
is useful for bi-amping.
Issue 2
Page 6 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
FACILITIES & CONNECTIONS
1
ON/OFF Button
MAINS LED
MUTE LED
2
3
4
5
1
2
3
4
5
INPUT A/B indicator LEDs
INPUT selector button
6
7
8
9
10
11
12 13 14
6
7
8
9
LOUDSPEAKER OUTPUTS Right
BALANCED XLR right input
11 IEC MAINS INPUT
12 LOOP output RCA sockets
13 INPUT B RCA sockets
14 INPUT A RCA sockets
BALANCED/RCA Selector for INPUT B
BALANCED XLR left input
10 LOUDSPEAKER OUTPUTS Left
Issue 2
Page 7 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Starting
Once all connections are made, switch on the unit, using the POWER button front of the unit. The MUTE LED
will light. Speaker outputs are muted for about 6 seconds, so no sound will be heard from the speakers. Once
the 6 seconds is up the MUTE LED goes out, indicating unit is settled, and ready for use.
IMPORTANT: BALANCED/RCA switch
The BALANCED/RCA switch (see page 7) is included to minimise noise when using the unit in RCA mode. In
most cases it will operate in BALANCED position on RCA inputs with no appreciable audible increase in noise.
There is no harm in operating the unit in this way.
However it is important, that if using the XLR (BALANCED) input, the switch must be set for BALANCED (up).
If the switch is not set for BALANCED on an XLR input, a 6dB reduction in loudness will occur and the benefits
of BALANCED operation will be lost.
INPUT A RCA
To use the RCA INPUT A, connect RCA source outputs to the INPUT A RCA sockets (see page 7). Select
INPUT A by pressing the INPUT select button so INPUT A LED is lit.
INPUT B RCA
To use the RCA INPUT B, connect RCA source outputs to the INPUT B RCA sockets (see page 7). Make sure
the BALANCED/RCA switch is set for RCA (down). Select INPUT B by pressing the INPUT select button so
INPUT B LED is lit.
INPUT B BALANCED
To use the balanced input, connect balanced source outputs to the balanced input XLR sockets (see page 7).
Make sure the BALANCED/RCA switch is set for BALANCED (up). Select INPUT B by pressing the INPUT
button so INPUT B LED is lit.
It is perfectly acceptable to use an RCA source device on INPUT A and a balanced XLR source on INPUT B
and use the INPUT select button to select between the two. The BALANCED/RCA switch should be in the
BALANCED position.
Note that the INPUT B BALANCED and RCA inputs are shared. It is not recommended to use both balanced
and single ended modes simultaneously on INPUT B. Loss and/or mixing of signal and/or equipment failure
may occur if both inputs are used simultaneously.
Alternatively, two RCA single-ended devices may be connected, one on INPUT A, and the other on input B, use
the INPUT select button to select between the two. For this scenario, the BALANCED/RCA switch should be
set for RCA (down).
Issue 2
Page 8 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEMS?
Basic problem-solving with an amplifier is similar to troubleshooting other electrical or electronic equipment. Always check the most obvious
possible causes first, such as the following examples:
Problem
Probable Cause
Remedy
No power when POWER Mains power plug is not fully inserted into rear Plug in securely.
button is pressed.
No sound
socket.
Mute function is still active.
Wait for the MUTE LED to go out.
Wrong connections between input sources and Check audio input lead connections.
the unit
Check speaker cables.
Speakers not connected, or incorrectly wired
Sound cut
Loose connection
Check speaker and input connections.
Output overload or short circuit
Switch unit off. Check speaker connections for shorting
strands or wires. When all has been double-checked
reduce volume and switch unit back on.
N.B. Take great care when bi-wiring or bi-amping that
speaker bass and treble linking straps are removed; see
speaker manual for more information.
Sound is not precise, Speakers are connected out of phase, i.e., Ensure speakers are connected with same polarity at
lacking in bass and stereo connections
to
one
speaker amplifier and speaker ends.
image.
(+ and –) are reversed.
Hum.
Audio connector plug not fully pushed in
Cable Fault
Insert plug securely.
Check cable is connected at both ends.
Unsuitable
(e.g. cable grounds not connected)
cable N.B. Some esoteric cables have internal wiring
intentionally disconnected/modified. For best results on
all inputs analogue AND digital, please use good quality
screened coax; signal and screens both separately
connected at both ends.
No audio output, or too Incorrect or missing connections
low level output.
Check connections and make sure they are secure.
If none of these actions affect a cure, please contact the dealer, or an authorised Musical Fidelity service agent. Remember; never open
the case of the M6PRX, as this will invalidate the guarantee.
Issue 2
Page 9 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Output
Power
260 Watts per channel into 8 Ohms (24 dBW)
Voltage
46 Volts RMS, 20Hz to 20 kHz; onset of clipping
(130 Volts peak-to-peak)
140 Amps
210
Current peak-to-peak
Damping factor
Output devices
4 pairs per channel
Line input
THD+N
<0.007% typical, 20 Hz to 20 kHz
>120 dB ‘A’-weighted
50k Ohms
Signal / noise ratio
Input impedance
Frequency response
+0, –1dB, 10Hz to 100 kHz
Connections
Line level inputs
1 pair line level XLR (balanced) connectors
2 pairs line level RCA connectors
Line level outputs
Speaker outputs
1 pair line level RCA connectors
4 pairs 4mm banana plug/binding posts
Power requirement
Mains voltages
115/230VAC 50/60Hz (factory pre-set)
100VAC 50/60Hz (alternative)
Consumption
750 Watts maximum
Weight
Unit only, unboxed
In shipping carton
19.7 kg (43⅓ lbs)
24.4 kg (53⅔ lbs)
Dimensions
Wide
440 mm (17⅓ ”)
High, including feet
125 mm (5 ”)
Deep (front to back) including terminals 390 mm (15⅓ ”)
Standard accessories
IEC type mains lead (10-Amp type)
Musical Fidelity reserves the right to make improvements which may result in
specification or feature changes without notice.
Issue 2
Page 10 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL HISTORY
RELEASE
Issue 1
DATE
CHANGES
1st Issue
14th October 2009
9th November 2009
Issue 2
Back panel updated
Issue 2
Page 11 of 11
Download from Www.Somanuals.com. All Manuals Search And Download.
|