Instructions for use
Thank you for purchasing the Musical Fidelity M6i dual mono Integrated amplifier.
The M6i is designed to be partnered with present and future M6 series products. This combination yields one of
the best high-fidelity systems available at any price.
Used properly and carefully, it should give many years of outstanding musical reproduction.
Dust regularly with a soft duster or soft brush, but be careful when using cleaning or polishing agents - they may
harm the surface finish.
If there are any questions about the audio system, please consult the dealer who is there to help and advise.
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY INFORMATION
IMPORTANT! (U.K. only)
This unit is supplied in the U.K. with mains lead fitted with a moulded 13 amp plug. If, for any reason, it is
necessary to remove the plug, please remove the fuse holder and dispose of the plug safely, out of reach of
children.
It must not be plugged into a mains outlet.
The wires in the mains lead supplied with this appliance are coloured in accordance with the following code:
Green and yellow .............................Earth
Blue................................................ Neutral
Brown ..................................................Live
WARNING – This appliance MUST be earthed
As the colours of the wires of the mains lead of this appliance may not correspond with the coloured markings
identifying the terminals in the plug, proceed as follows:
•
•
•
•
The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked
with the letter E or coloured green or green-and-yellow, or by the earth symbol:
The wire which is coloured brown must be connected to the terminal which is marked with the letter L or
coloured red.
The wire which is coloured blue must be connected to the terminal which is marked with the letter N or
coloured black.
If connecting to a BS1363 plug, a 13 amp fuse must be used.
WARNING:
ANY MODIFICATIONS TO THIS PRODUCT NOT EXPRESSLY
APPROVED BY MUSICAL FIDELITY WHO IS THE PARTY RESPONSIBLE
FOR STANDARDS COMPLIANCE COULD VOID THE USER'S
AUTHORITY TO OPERATE THIS EQUIPMENT.
Issue 4
Page 3 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL ADVICE
Installation, Precautions & User Information
This new M6i is designed and built to provide trouble-free performance, but as with all electronic devices it is
necessary to observe a few precautions:
•
•
•
Heed all warnings shown on the back of the product.
Only connect the M6i to a mains outlet having the same voltage as marked at the back of the unit.
Always ensure that when disconnecting and reconnecting your audio equipment the mains supply is
switched off.
•
•
Position the mains lead and signal interconnects where they are not likely to be walked on or trapped by
items placed on them.
Do not use near water, or place water-filled containers on the M6i, for example, a flower vase or potted
plants. If water does spill inside, immediately pull out the mains plug from the wall socket and inform
your dealer, who should then check the unit before further use. Entry of liquid into the M6i is
dangerous, and may cause electric shock or fire hazard.
•
•
Do not place the unit near direct heat sources such as radiators, direct sunlight or other equipment.
Do not remove any covers or try to gain access to the inside. There are no internal adjustments or fuses you
can replace yourself. Refer all service work to an authorised Musical Fidelity agent.
* Note: Unauthorised opening of the equipment will invalidate any warranty claim.
•
Dust regularly with a soft cloth or soft brush but be careful when using cleaning or polishing agents - they
may harm the surface finish.
The electronics in modern hi-fi equipment is complex and may, therefore, be adversely affected or damaged by
lightning. For protection of the audio system during electrical storms, remove the mains plugs.
If after-sales service is required, to help the dealer identify the M6i please quote the serial number located on
the rear panel of the unit.
Issue 4
Page 4 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
ITEM DISPOSAL INFORMATION
DISPOSAL
The crossed out wheeled bin label that appears on the back panel of the product indicates that
the product must not be disposed of as normal household waste. To prevent possible harm to the
environment please separate the product from other waste to ensure that it can be recycled in an
environmentally safe manner. Please contact local government office or retailer for available collection
facilities.
DISPOSITION
La poubelle sur roulettes barrées X, qui apparaît en logo sur le panneau arrière du produit, indique que celui-ci ne
doit pas être traité comme un déchet domestique commun. Afin de protéger l'environnement, ce produit électronique devra
être géré séparément et donc recyclé selon les nouvelles normes Européennes Rohs concernant les déchets d'appareils
électroniques. Prière de contacter les services concernés gouvernementaux ou votre point de vente pour l'élimination et
l'enlèvement de déchets électroniques équipés de composants électroniques.
DISPOSAL
La etiqueta cruzada hacia fuera del compartimiento que aparece en el panel trasero del producto indica que el
producto no se debe reciclarse como basura normal de la casa. Para prevenir daños posible al ambiente separe por favor el
producto de otras basura para asegurarse de que puede ser reciclada de una manera ambientalmente segura. Entre en
contacto por favor a su oficina gubernamental local o a su minorista para las instalaciones disponibles de la colección.
RIFIUTI
L'etichetta del cassonetto barrato riportato sul retro dell'apparecchio indica che il prodotto non deve essere
smaltito tramite la procedura normale di smaltimento dei rifiuti domestici. Per evitare eventuali danni all'ambiente, separare
questo prodotto da altri rifiuti domestici in modo che possa venire riciclato in base alle procedure di rispetto ambientale. Per
maggiori dettagli sulle aree di raccolta disponibili, contattate l'ufficio govenativo locale od il rivenditore del prodotto.
FACHGERECHTE ENTSORGUNG:
Das auf der Geräterückseite angebrachte Label deutet darauf hin, dass das Produkt nicht mit konventionellem
Hauskehricht entsorgt werden darf. Um Schäden und Verschmutzungen an Umwelt und Mensch zu vermeiden, muss das
Produkt fachgerecht entsorgt und von anderem Abfall getrennt werden. Wenden Sie sich bei Fragen hierzu an Ihren
Fachhändler oder an eine öffentliche Informationsstelle.
AFVAL
Het label op de achterzijde van dit apparaat, een afvalbak op wielen met een kruis doorgehaald, geeft aan dat dit
apparaat niet samen met gewoon huishoudafval mag worden weggegooid. Om mogelijke schade aan onze leefomgeving te
voorkomen dient dit apparaat, gescheiden van gewoon huishoudelijk afval, te worden afgevoerd zodat het op een
milieuvriendelijke manier kan worden gerecycled. Neem voor beschikbare inzamelplaatsen contact op met uw gemeentelijke
reinigingsdienst of met uw elektronica leverancier.
HÄVITTÄMINEN
Yliruksattua jäteastiaa kuvaava tarra tuotteen takalevyssä kertoo, että tuotetta ei saa käsitellä normaalina
talousjätteenä. Ympäristön suojelemiseksi on tuote pidettävä erillään muusta jätteestä ja se on kierrätettävä ekologisesti
kestävällä tavalla. Ota yhteyttä laitteen myyjään tai Pirkanmaan Ympäristökeskukseen lähimmän kierrätyskeskuksen
löytämiseksi.
AFSKAFNING
Logoet med en skraldespand med kryds over på bagsiden af apparatet indikerer at dette produkt ikke må kasseres
som normal husholdningsaffald. For at forebygge mulig skade på miljøet, bedes De separere dette produkt fra andet affald,
og sikre at det bliver genbrugt på en miljørigtig måde. Kontakt venligst de lokale myndigheder eller din forhandler for
oplysning om nærmeste tilgængelige opsamlingssted for elektronikaffald.
ΔΙΑΔΙΚΑΣΙΑ ΑΠΟΡΡΙΨΗΣ
ΤΟ ΣΗΜΑ ΜΕ ΤΟΝ ΔΙΑΓΕΓΡΑΜΜΕΝΟ ΤΡΟΧΗΛΑΤΟ ΚΑΔΟ ΑΠΟΡΡΙΜΑΤΩΝ ΣΤΗΝ ΠΙΣΩ ΟΨΗ ΤΟΥ
ΜΗΧΑΝΗΜΑΤΟΣ
ΔΗΛΩΝΕΙ ΟΤΙ ΤΟ ΠΡΟΙΟΝ ΑΥΤΟ ΔΕΝ ΠΡΕΠΕΙ ΝΑ ΔΙΑΧΕΙΡΙΣΘΕΙ ΣΑΝ ΣΥΝΗΘΙΣΜΕΝΟ ΟΙΚΙΑΚΟ ΑΠΟΒΛΗΤΟ.
ΠΡΟΣ ΑΠΟΦΥΓΗ ΕΝΔΕΧΟΜΕΝΗΣ ΕΠΙΒΑΡΥΝΣΗΣ ΤΟΥ ΠΕΡΙΒΑΛΛΟΝΤΟΣ, ΞΕΧΩΡΙΣΤΕ ΤΟ ΠΡΟΙΟΝ ΑΠΟ ΤΑ ΑΛΛΑ
ΑΠΟΡΡΙΜΑΤΑ ΩΣΤΕ ΝΑ ΕΞΑΣΦΑΛΙΣΘΕΙ Η ΑΝΑΚΥΚΛΩΣΗ ΤΟΥ ΜΕ ΤΟΝ ΠΡΕΠΟΝΤΑ ΤΡΟΠΟ.
ΠΑΡΑΚΑΛΟΥΜΕ ΝΑ ΕΠΙΚΟΙΝΩΝΗΣΕΤΕ ΜΕ ΤΗΝ ΤΟΠΙΚΗ ΥΠΗΡΕΣΙΑ ΑΝΑΚΥΚΛΩΣΗΣ Η ΜΕ ΤΟ ΚΑΤΑΣΤΗΜΑ ΑΓΟΡΑΣ
ΓΙΑ ΠΕΡΙΣΣΟΤΕΡΕΣ ΛΕΠΤΟΜΕΡΕΙΕΣ.
Issue 4
Page 5 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION
Introduction
Congratulations on the purchase of the new M6i integrated amplifier. Great attention has been paid to internal
layout, isolating each circuit section to prevent possible interaction.
The unit features a finely tuned and tweaked preamplifier, for smooth sound coupled with low noise and virtually
no distortion.
The power amplifier consists of two monoblock amplifiers with separate supplies for the absolute best in
separation and imaging. Generously rated, they are enough to drive even the most demanding loudspeakers
with ease. Low distortion and very quiet they will deliver all music types exactly as the artist originally intended.
The resultant performance achieved by this unit is among the best in the world. It has excellent signal to noise
ratio, low distortion, wide bandwidth and dynamic range, with extraordinary resolution and fine detail.
Cleaning
Before cleaning the unit, switch off power at the mains switch and remove the mains plug from the wall socket.
Clean the cabinet and remote control unit using a moist cloth. Using solvents, white spirit or thinners is not
advised, as they could damage the surface finish.
Installation
Position the M6i on a stable, horizontal surface where there is no risk of it being knocked, or subjected to
vibration such as from loudspeakers.
Important note:
In normal operation, the unit dissipates a small quantity of power at all times, and it is important
that it is adequately ventilated. The top and bottom are perforated to allow the smooth flow of heat
through the unit. It is therefore not recommended that the unit is enclosed in a cabinet or placed
where the ventilation holes are impeded as this could result in excessive heat build-up.
The M6i must be protected from humidity – if the unit is moved from a cold place to a warm room,
leave the unit for an hour or so to allow sufficient time for the moisture to evaporate.
Power Connections
The M6i is supplied with a standard IEC mains cable which plugs into the IEC socket at the back of the unit (see
page 7)
Audio Connections
RCA Inputs: Connect all RCA single-ended sources to relevant analogue inputs (see page 7 for more
information). Use good quality fully connected (signal and ground) coaxial phono cables for all RCA signal
connections.
XLR Inputs: Connect any XLR balanced source to balanced analogue input (see page 7 for more information).
Use good quality fully connected (signals and ground) balanced XLR cables for all XLR signal connections.
Outputs: Connect loudspeakers to the terminals on the back panel marked as LEFT and RIGHT SPEAKER
outputs
The TAPE output allows loop through of analogue signals for example, to pass on to recorder or monitor. It is
also the ideal output to connect our headphone amps into.
The PRE-OUT output allows analogue signals controlled by the volume, to pass on to a second amplifier. This
is useful for bi-amping.
Issue 4
Page 6 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
FACILITIES & CONNECTIONS
1
2
3
4
5
1
2
3
ON/OFF Button
4
5
VOLUME control
TAPE MONITOR button
IR RECEIVER lens
BALANCED, CD, USB, TUNER, HT/AUX,
TAPE input selector buttons
6
7
8
9
10
11
12 13
6
7
8
9
LOUDSPEAKER OUTPUT Right
USB input from computer
10 CD, TUNER, AUX/HT, TAPE input
RCA Sockets
11 PRE, TAPE output RCA sockets
12 LOUDSPEAKER OUTPUT Left
13 IEC MAINS INPUT
BALANCED XLR right and left inputs
HT/AUX Selector for HT/AUX input
Issue 4
Page 7 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
REMOTE CONTROL HANDSET
The universal remote control shown below enables functions from this and related units to be operated from a
convenient distance.
Equivalent buttons on the remote control have the same functions as those on the front panel of the unit. Other
functions are only available by remote control.
As the handset uses an invisible infra-red light beam, the front edge must be pointed directly towards the
receiver window at the front of the player, without visual obstruction between them.
If the range of the remote control greatly decreases, replace the batteries with new ones. Do not mix old and
new batteries – two are required, size AAA, LR03 or SUM-4.
Please dispose of used batteries in accordance to local regulations.
CD Digital input section
CD - selects internal CD player (on CD)
OPTICAL – selects optical input
SPDIF – selects SPDIF (RCA coax) input
USB – selects USB input (on CD)
Amplifier section
BALANCED - selects balanced input
USB – selects USB input (on amplifier)
AUX/HT - selects AUX/HT input
CD - selects CD input (on amplifier)
TUNER - selects TUNER input
TAPE - selects TAPE input
MUTE - mutes speaker outputs
(until pressed again).
VOLUME ▲ - increases volume
VOLUME ▼ - reduces volume
CD player section
DISPLAY – dims display
TIME – displays track time/time remaining
0-9 Buttons – Used to select track
numbers
CHECK – check pre-programmed tracks
PROGRAM – programs selection and
CLEAR – clears selected pre
order of tracks
programmed track
INTRO – plays first 10 seconds of each
A/B sets repeat start/end to repeat
track
section of track
REPEAT – repeats whole disk or selected
SHUFFLE – plays back tracks in
tracks
random order
SEARCH – fast forward/backward through
TRACK – next/previous track
track
PAUSE/PLAY – stop/start CD
STOP – Stop playing/Eject CD
playback
Issue 4
Page 8 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Starting
Once all connections are made, switch on the unit, using the POWER button front of the unit. The MUTE LED
will light. Speaker outputs are muted for about 6 seconds, so no sound will be heard from the speakers. Once
the 6 seconds is up the MUTE LED goes out, indicating unit is settled, and ready for use.
Volume
The volume should be adjusted for normal listening levels. This is done by turning the volume up/down knob on
the front panel. Adjusting the volume can also be achieved using the remote handset, using the volume
up/down buttons (see page 8).
Mute (Remote Control only)
The sound from the speakers may be muted by use of the MUTE button on the remote. Press once, and MUTE
LED will light indicating muted state. No sound will be heard from the speakers.
To return to listening; simply press the MUTE button again so MUTE LED is no longer lit.
BALANCED
To use the balanced input, connect balanced source outputs to the balanced input XLR sockets (see page 7).
Select BALANCED input by pressing the BALANCED INPUT button so BALANCED INPUT LED is lit.
Selecting the BALANCED input can also be achieved by pressing the corresponding button on the remote
handset (see page 8).
CD
To use the CD input, connect CD player outputs to the CD input RCA sockets (see page 7). Select CD input by
pressing the CD button so CD LED is lit. Selecting the CD input can also be achieved by pressing the
corresponding button on the remote handsets (see page 8).
Tuner
To use the tuner input, connect tuner outputs to the TUNER input RCA sockets (see page 7). Select TUNER
input by pressing the TUNER button so TUNER LED is lit. Selecting the TUNER input can also be achieved by
pressing the corresponding button on the remote handset (see page 8).
AUX/HT
To use the AUX input as a standard input, move the AUX/HT switch on the back panel to the AUX position.
Connect source outputs to the AUX input RCA sockets (see page 7). Select AUX input by pressing the AUX
button so AUX LED is lit. Selecting the AUX input can also be achieved by pressing the corresponding button
on the remote handset, (see page 8).
To use the AUX/HT input as a HT input, move the AUX/HT switch to the HT position. This input is now
unaffected by the volume control, allowing volume control on an external Home Theatre processor to be used
directly. Connect Home theatre or other source outputs to the AUX input RCA sockets (see page 7). Select
AUX input by pressing the AUX button so AUX LED is lit.
IMPORTANT: Take great care when using the input in HT mode. Ensure that the volume control is turned right
down on the HT processor when first setting up. The HT mode is designed for sources which require their own
volume control to be used. Connecting sources in HT mode with no volume control could result in damage to
hearing and/or speakers due to uncontrolled loud sounds.
Issue 4
Page 9 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
TAPE
To use the TAPE input, connect external source to the TAPE input (see page 7). Select TAPE input by pressing
the TAPE button so TAPE LED is lit. Selecting the TAPE input can also be achieved by pressing the
corresponding button on the remote handset (see page 8).
TAPE MONITOR
To record to tape, (or alternatively CD recorder, DAT, minidisk or computer soundcard analogue input) connect
the tape out to the tape recorder line in. Press the input selector button on the front panel or remote control.
This source will now be routed to the M6i TAPE OUT for recording by tape deck.
The recording can be directly monitored through the loudspeakers by pressing the TAPE MONITOR button so
the TAPE MONITOR LED is lit. Press again to return back to the original input being listened to (and TAPE
MONITOR LED is out again).
On some 3 head tape decks there is an additional tape/source switch which should be in the 'TAPE' position for
this to work. If in doubt, please consult tape deck operating manual.
Note – adjustment of the volume control has no effect on the recording level.
Issue 4
Page 10 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
USB input
For the USB input, the LED will flash in absence of digital input signal. When a signal is present, the LED will
light continuously.
Computer setup for input USB input
A good quality USB A to B cable is required to connect the unit to the computer.
Plug the B (square) end into the socket in the back of the M6i
Plug the A (rectangle) end into a free USB socket on the computer.
The computer should detect the new hardware and install a generic driver automatically (No setup or driver
disk required).
CD, MP3, WAV files played on any software should now play through the M6i. This device has been designed
to work with PC Windows 98, ME, 2000, XP as well as Apple Macintosh OS X.
Please note:
This device is a high speed serial data processor, and by its nature, requires a very high volume of USB
bandwidth. It will benefit greatly from being the only device connected on its USB ‘bus’. Sharing the same bus
with other devices may cause unwanted artefacts such as dropouts or temporary loss of signal. This especially
includes the use of the M6i on a USB hub/splitter alongside other USB components
PC users-
Check the computer has picked up the device and is currently using it by clicking: (most Windows versions)
-
-
-
-
-
Start
Settings
Control panel
Sounds and Multimedia
Audio
Check that “USB audio device” appears under PREFERRED AUDIO DEVICE tab
A second mixer will now be available which will be the default mixer whenever the M6i is plugged in. Use this
mixer to select the source or adjust levels if required.
Mac users-
Check the computer has picked up the device and is currently using it by clicking: (MAC OS X)
-
-
-
System preferences
Hardware
Sound
Check that “USB audio DAC” is selected under the OUTPUT tab.
If the computer’s warning sounds/chimes are to played through the M6i, make sure it is selected under the
SOUND EFFECTS tab too.
Note: USB may also be selected as an output in some individual programs
Issue 4
Page 11 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
PROBLEMS?
Basic problem-solving with an amplifier is similar to troubleshooting other electrical or electronic equipment. Always check the most obvious
possible causes first, such as the following examples:
Problem
Probable Cause
Remedy
No power when POWER Mains power plug is not fully inserted into rear Plug in securely.
button is pressed.
No sound
socket.
Mute function is still active.
Press the MUTE button on the remote control to cancel.
Wrong connections between input sources and Check audio input lead connections.
the unit
Check speaker cables.
Speakers not connected, or incorrectly wired
Sound cut
Loose connection
Check speaker and input connections.
Output overload or short circuit
Switch unit off. Check speaker connections for shorting
strands or wires. When all has been double-checked
reduce volume and switch unit back on.
N.B. Take great care when bi-wiring or bi-amping that
speaker bass and treble linking straps are removed; see
speaker manual for more information.
Sound is not precise, Speakers are connected out of phase, i.e., Ensure speakers are connected with same polarity at
lacking in bass and stereo connections
to
one
speaker amplifier and speaker ends.
image.
(+ and –) are reversed.
Hum.
Audio connector plug not fully pushed in
Cable Fault
Insert plug securely.
Check cable is connected at both ends.
Unsuitable
(e.g. cable grounds not connected)
cable N.B. Some esoteric cables have internal wiring
intentionally disconnected/modified. For best results on
all inputs analogue AND digital, please use good quality
screened coax; signal and screens both separately
connected at both ends.
No audio output, or too Incorrect or missing connections
low level output.
Check connections and make sure they are secure.
No audio output from USB
input
USB Cable not connected
Check connections and make sure they are secure.
USB Driver not selected (PC or MAC)
See P.9 PC users or Mac users section
Not detected when
connected to USB
USB Cable faulty
Check and replace cable
USB not working/enabled on computer
Correct USB drivers not installed
Check USB port functions with another device.
Please check with the computer manufacturer. Enquire
about USB driver or update.
(can happen particularly with factory-
preinstalled Windows operating systems)
Dropouts in sound (USB
input)
Shared USB port with another device
Computer busy with another application
Computer low on resources
Avoid sharing the USB port with other devices, if
possible.
At times an application (program) may intervene,
sometimes invisibly e.g. a virus scanner. When this
happens, computer resources are temporarily used up,
and playback may falter. This is not a fault. Try running
fewer applications if possible.
Remote control does not Amplifier’s POWER switch is set to off.
Set switch to on.
work.
One or more batteries fitted the wrong way Insert batteries correctly.
round.
Change batteries for a new set.
Batteries are flat.
Ensure there is no obstruction between the remote
Remote control is not pointed directly towards control and amplifier front.
the front panel of the amplifier.
Lighting such as fluorescent, incandescent, or even
Interference from another source.
sunlight contains large amounts of infra red radiation.
Ensure such sources are not shining directly on the infra
red window as this could swamp the signal from the
remote control.
Also check the system and any other nearby remotes for
stuck buttons.
Remote control range has Batteries are running out
greatly reduced
Change batteries for a new set.
If none of these actions affect a cure, please contact the dealer, or an authorised Musical Fidelity service agent. Remember; never open
the case of the M6i, as this will invalidate the guarantee.
Issue 4
Page 12 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Output
Power
200 Watts per channel into 8 Ohms (23dBW)
Voltage
45 Volts RMS, 20Hz to 20 kHz; onset of clipping
(126 Volts peak-to-peak)
45 Amps
170
Current peak-to-peak
Damping factor
Output devices
2 pairs per channel
Line input
THD+N
<0.01% typical, 20Hz to 20 kHz
>100dB ‘A’-weighted
38k Ohms
Signal / noise ratio
Input impedance
Frequency response
+0, –0.1dB, 10Hz to 20 kHz
Connections
Line level inputs
1 pair line level XLR (balanced) connectors
4 pairs line level RCA connectors
Line level outputs
1 pair line level RCA connectors, constant level TAPE outputs
1 pair line level RCA connectors, preamp outputs for e.g. biamping
USB input
USB type “B” (square) socket
Speaker outputs
2 pairs 4mm banana plug/binding posts
Power requirement
Mains voltages
115/230VAC 50/60Hz (factory pre-set)
100VAC 50/60Hz (alternative)
Consumption
680 Watts maximum
Weight
Unit only, unboxed
In shipping carton
16.6 kg (36½ lbs)
21.3 kg (47 lbs)
Dimensions
Wide
440 mm (17⅓”)
High, including feet
125 mm (5”)
Deep (front to back) including terminals 400 mm (15¾”)
Standard accessories
IEC type mains lead (10-Amp type)
M6 remote control
Batteries, LR03 or AAA, manganese alkaline type - 2 off
Musical Fidelity reserves the right to make improvements which may result in
specification or feature changes without notice.
Issue 4
Page 13 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUAL HISTORY
RELEASE
Issue 1
Issue 2
Issue 3
Issue 4
DATE
CHANGES
1st release
24th July 2009
14th October 2009
16th October 2009
9th November 2009
Formatting
Page 11 footer
Back panel updated
Issue 4
Page 14 of 14
Download from Www.Somanuals.com. All Manuals Search And Download.
|