Models
22” Self-Propelled
This Instruction Book contains information for several models.
Read and keep this book for future reference.
This book contains important information on
SAFETY, ASSEMBLY, OPERATION, AND MAINTENANCE.
PRODUCT INFORMATION
The owner must be certain that all
the product information is included with the unit.
This information includes
the INSTRUCTION BOOKS,
the REPLACEMENT PARTS and the WARRANTIES.
This information must be included to make sure state laws
and other laws are followed.
RECORD THE FOLLOWING INFORMATION ABOUT YOUR UNIT.
THIS INFORMATION IS NECESSARY WHEN ORDERING PARTS
OR IN CASE OF LOSS OR THEFT.
BUILT IN THE
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
OWNER’S INFORMATION
This instruction book is written for a person with some mechanical ability. Like most service books,
not all the steps are described. Steps on how to loosen or tighten fasteners are steps anyone can
follow with some mechanical ability. Read and follow these instructions before you use the unit.
Know your product: If you understand the unit and how the unit operates, you will get the best
performance. As you read this manual, compare the illustrations to the unit. Learn the location and
the function of the controls. To help prevent an accident, follow the operating instructions and the
safety rules. Keep this manual for future reference.
IMPORTANT: Many units are not assembled and are sold in cartons. It is the responsibility of the
owner to make sure the assembly instructions in this manual are exactly followed. Other units are
purchased in an assembled condition. On assembled units, it is the responsibility of the owner to
make sure the unit is correctly assembled. The owner must carefully check the unit according to
the instructions in this manual before it is first used.
RESPONSIBILITY OF THE OWNER
The responsibility of the owner is to follow the instructions below.
1. Carefully read and follow the rules for safe operation.
2. Follow all the assembly and preparation instructions.
3. Inspect the unit.
4. Make sure that the operator of the unit knows how to correctly use all standard and accessory
equipment.
5. Operate the unit only with guards, shields, and other safety items in place and working correctly.
6. Correctly adjust the unit.
7. Service the unit only with authorized or approved replacement parts.
8. Complete all maintenance on the unit.
Engine Exhaust, some of its constituents, and
certain vehicle components contain or emit
chemicals known to the State of California to
cause cancer and birth defects or other repro-
ductive harm.
Battery posts, terminals and related accesso-
ries contain lead and lead compounds, chemi-
cals known to the State of California to cause
cancer and birth defects or other reproductive
harm. WASH HANDS AFTER HANDLING.
3
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
Safe Operation Practices for Walk-Behind Mowers.
This cutting machine is capable of amputating hands and feet and throwing objects. Failure to ob-
serve the following safety instructions could result in serious injury or death.
tion which can cause drowsiness or affect
your ability to operate this machine safely.
I. General Operation
1. Read, understand, and follow all instruc-
tions on the machine and in the manual(s).
Be thoroughly familiar with the controls and
the proper use of the mower before starting.
15. Never operate mower in wet grass. Always
be sure of your footing; keep a firm hold on
the handle and walk; never run.
16. Disengage the self-propelled mechanism
or drive clutch on mowers so equipped be-
fore starting the engine (motor).
2. Do not put hands or feet near or under rotat-
ing parts. Keep clear of the discharge open-
ing at all times.
17. If the equipment should start to vibrate ab-
normally, stop the engine (motor) and check
immediately for the cause. Vibration is gen-
erally a warning of trouble such as a blade
that is damaged, a loose blade, or the en-
gine mounting bolts are loose.
3. Only allow responsible individuals, who are
familiar with the instructions, to operate the
mower.
4. Thoroughly inspect the mower and area
where the equipment is to be used. Clear
the area of objects such as rocks, toys, wire,
bones, sticks etc., which could be picked up
and thrown by the blade.
18. Always wear safety goggles or safety
glasses with side shields when operating
mower to protect your eyes from foreign ob-
jects which can be thrown from the unit.
5. Be sure the area is clear of other people be-
fore mowing. Stop mower if anyone enters
the area.
19. Plan your mowing pattern to avoid dis-
charge of material toward roads, sidewalks,
bystanders and the like.
6. Do not operate the mower when barefoot or
wearing open sandals. Always wear sub-
stantial foot wear.
20. After striking a foreign object, stop the en-
gine. Remove the wire from the spark plug.
Inspect the blade and mower for damage. If
damaged, repair before starting and operat-
ing the mower.
7. Do not pull mower backwards unless abso-
lutely necessary. Look down and behind be-
fore and while moving backwards.
21. Keep any washout ports and other mower
housing service openings closed when
mowing.
8. Do not operate the mower without proper
guards, plates, grass catcher or other safety
protective devices in place.
II. Slope Operation
Slopes are a major factor related to slip and fall
accidents which can result in severe injury. All
slopes require extra caution. If you feel uneasy
on a slope, do not mow it.
9. See manufacturer’s instructions for proper
operation and installation of accessories.
Only use accessories approved by the
manufacturer.
DO:
10. Stop the blade(s) when crossing gravel
drives, walks, or roads.
Mow across the face of slopes; never up
and down. Do not mow excessively steep
slopes (maximum 15 degrees) or areas
where the ground is very rough. See the
“Guide” in the back of this manual to check
a slope. Exercise extreme caution when
changing direction on slopes.
11. Stop the engine (motor) whenever you
leave the equipment, before cleaning the
mower or unclogging the chute.
12. Shut the engine (motor) off and wait until the
blade comes to complete stop before re-
moving grass catcher.
Remove objects such as rocks, tree limbs,
etc.
13. Mow only in daylight or good artificial light.
14. Do not operate the mower while under the
Watch for holes, ruts, or bumps. Tall grass
can hide obstacles.
influence of alcohol, drugs or other medica-
F-040411L
(Continued Following Page)
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT
DO NOT:
nect the spark plug wire, and keep the wire
away from the plug to prevent accidental
starting. Always wear eye protection when
you make adjustments or repairs.
Do not mow near drop-offs, ditches, or em-
bankments. The operator could lose footing
or balance.
4. Keep all nuts and bolts, especially blade at-
tachment bolts, tight and keep equipment in
good condition.
Do not mow excessively steep slopes.
Do not mow on wet grass. Reduced footing
could cause slipping.
5. Never tamper with safety devices. Check
their proper operation regularly.
III. Children
6. To reduce fire hazard, keep mower free of
grass, leaves, or other debris build-up.
Clean up oil or fuel spillage. Allow mower to
cool before storing.
Tragic accidents can occur if the operator is not
alert to the presence of children. Children are
often attracted to the mower and the mowing
activity. Never assume that children will remain
where you last saw them.
7. Stop and inspect the equipment if you strike
an object. Repair, if necessary, before re-
starting.
1. Keep children out of the mowing area and
under the watchful care of a responsible
adult.
8. Never attempt to make wheel height adjust-
ments while the engine (motor) is running.
2. Be alert and turn mower off if children enter
the area.
9. Always disconnect electric mowers (live op-
erated) before cleaning, repairing, or ad-
justing.
3. Before and while moving backwards, look
behind and down for small children.
4. Never allow children to operate the mower.
10. Grass catcher components are subject to
wear, damage, and deterioration, which
could expose moving parts or allow objects
to be thrown. Frequently check components
and replace with manufacturer’s recom-
mended parts, when necessary. For stor-
age, always make sure grass catcher is
empty.
5. Use extra care when approaching blind cor-
ners, shrubs, trees, or other objects that
may obscure vision.
IV. Service
*1. Use extra care in handling gasoline and oth-
er fuels. They are flammable and vapors are
explosive.
11. Mower blades are sharp and can cut. Wrap
the blade(s) or wear gloves, and use extra
caution when servicing them.
a. Use only an approved container.
b. Never remove gas cap or add fuel with 12. Do not change the engine governor setting
the engine running. Allow engine to cool
before refueling. Do not smoke.
or over-speed the engine.
13. Frequently check the blade for wear or dam-
ages such as cracks and nicks. A blade that
is bent or damaged must be immediately re-
placed with a factory replacement blade.
For safety and good cutting performance,
replace the blade every two years. Fre-
quently check the blade bolt and the engine
mounting bolts. Replace damaged bolts
and tighten loose bolts.
c. Never refuel the machine indoors.
d. Never store the machine or fuel contain-
er inside where there is an open flame,
such as a water heater.
*2. Never run an engine indoors or inside a
closed area.
3. Never make adjustments or repairs to items
such as the height adjusters or grass catch- 14. Use only original equipment or authorized
er with the engine (motor) running. Discon- replacement parts.
* Asterisked items do not apply to electric mowers.
5
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFE MOWING GUIDE
Every person who uses power equipment
gency. Learn how to cut and how to keep con-
trol of the mower at all times.
Many mowers are started manually. When us-
ing a pull start or rope start, place your feet
firmly and away from the blade. Hold the rope
handle securely, but never wrap the rope
around your arm or fingers for a “better grip”.
The mower is designed for use by one person.
Always mow alone. Never carry passengers.
Carrying a passenger is dangerous for the
passenger and the operator. A mower is not for
amusement or for carrying objects.
must learn the difference between proper and
improper use, safe and unsafe mowing prac-
tices. Read the next few pages carefully.
They can help you learn. Too often the mow-
er user is inexperienced, not properly in-
structed, or has not read the Instruction Book
and instructions on the unit before using it for
the first time. This can result in unsafe use en-
dangering the operator, bystanders, and the
equipment. Another result can be a poor ap-
pearance of the area mowed.
Read this Instruction Book. Read the in-
structions on the unit. Operate the mower ac-
cording to the Safe Mowing Guide and other
safety rules and recommendations in this In-
struction Book and on the unit. Make sure any-
one who uses the unit has read the instructions
and has been told how to operate the mower
safely.
Is the area you are planning to mow wet? Nev-
er cut a wet lawn. Cutting wet grass can cause
an accident. It can affect mower performance
and also cause problems with future lawn
growth and appearance. Wet grass is slippery
and might cause the operator to fall or the
mower to slip. Someone could be hurt by
touching the blade. Wet grass tends to clog the
mower, causing poor discharge. Wet clippings
bunch up on the lawn retarding the growth of
grass. A wet mower can cause parts to rust
and reduce the useful life of the unit.
Your mower is designed to provide good ser-
vice and durability in normal residential cut-
ting. If the mower is not properly serviced and
maintained or used on unsuitable terrain or in
conditions not suitable for mowing, product
performance and safety will be reduced.
Proper attire is an important part of safe mow-
ing. Safety glasses protect the eyes from
thrown objects. Safety shoes with steel toes
can protect a foot from being cut by the blade.
Shirts and pants that cover the arms and legs
can stop or deflect a thrown object.
When you look over the lawn, refresh your
memory about hard, immovable obstacles
such as pipes, stumps, and rocks and avoid
them. They can cause damage to the mower
or an accident injuring the operator or a by-
stander. Take a litter bag along and walk over
the area to be cut. Pick up any stones, toys,
wire, bones, or other loose objects. These
items can damage the mower or they can be-
come dangerous flying objects if the mower
blade hits them. The blade of a power mower
travels very fast. It can throw rocks and other
objects with force over long distances. Objects
thrown by mowers can break windows, cause
Practice using the mower before you actually
begin cutting grass. Select a large open level
area. Learn the location and function of the
controls and how they work. It is important that
the blade can be stopped quickly in an emer-
F-040411L
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFE MOWING GUIDE
bruises, or even put out an eye. Often the per-
improve the performance, help the engine stay
cooler, extend the life of moving parts, and
minimize the danger of fire. People get burned
working with and around their mowers for oth-
er reasons than fire and explosions. It takes
only a few seconds of operation for the engine
and the muffler to become hot. Do not touch
these parts when the mower is running. Stop
the engine and let it cool down before servicing
the mower. Remember, exhaust fumes can be
dangerous. Never operate the engine indoors
or in an enclosed area.
son hurt by a thrown object is a bystander such
as a child, another family member or a neigh-
bor. Keep people and pets completely away
from the mowing area. Direct the mower’s dis-
charge away from areas where people can be.
Planning your mowing pattern has a double
benefit. It can reduce chances of an injury and
make the clean up after mowing easier.
Are there ditches,
walls, or major in-
clines in the area to be
cut? Plan the mowing
pattern to avoid such
danger areas. In-
clines and rough ter-
rain must be mowed
carefully and some
areas must not be cut
with a mower at all.
With walk behind
equipment,
mow
across the incline so
that if you or the mow-
er slip, you won’t run
into each other.
Never mow slopes greater than 15 degrees.
See the “Guide” in the back of this Instruction
Book to check any slopes.
Getting a new mower can be a big event for a
family. Let family members satisfy their curios-
ity about the mower and at the same time, tell
them about its dangers. Remember, a mower
is not a toy and is not for use by children or any-
one lacking in age, strength or experience.
As with any power equipment, a mower can be
dangerous if not assembled, misused, or not
properly maintained. The most important rule
is to always use good judgement and common
sense.
Your mower will cut thick grass and heavy
plant stems with ease. Fingers and toes are no
more resistant to the mower’s blade. Many
people are injured because they “forgot” and
reached into the discharge chute. Always treat
your lawn mower as if the blade is rotating.
Never perform any service or try to make any
adjustment,except carburetor, while the en-
gine is running.
Ready to start cutting? Not yet. Be sure the
mower has been fully assembled according to
directions in the Instruction Book. Even if as-
sembly was done by a lawn and garden shop
or the store where the unit was purchased, it
must be checked. Are all nuts, bolts and
screws tight? Does the engine have oil? These
items must be checked periodically throughout
the life of the mower.
Your mower has a gasoline engine. Gas is
dangerous. Store fuel only in a approved gas
container. Do not store large amounts of gas.
Put out all cigarettes, pipes and cigars before
working with gasoline. Store fuel and the mow-
er itself in a well ventilated area away from any
possible source of ignition such a pilot light on
a furnace. If the mower is to be stored for an ex-
tended time, remove the gas from the tank.
This minimizes the chance of a fire and keeps
the tank clear of deposits and old gasoline,
thus improving mower performance. Move the
mower outside before adding gasoline. Use a
funnel and wipe up any spilled fuel before start-
ing. Remember, gasoline expands when
heated so leave some expansion room. Also,
most mower gas caps are vented to allow for
expansion. Always use the proper cap. People
are needlessly burned by fires, hurt in explo-
sions, mowers and other property are dam-
aged because of failure to follow basic safety
rules related to gasoline and fueling.
Use only accessories suited for your mower.
Use of improper accessories can reduce the
safety designed into both the mower and the
accessory, it can even damage the unit. Read
and follow the instructions which come with the
accessory and the mower.
Never add gasoline to an engine that is running
or that is hot from recent use, this can cause an
accident. Remove dry grass and other debris
from the mower. Keeping the mower clean will
F-040411L
7
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFE MOWING GUIDE
Use only original equipment or approved sub-
in the rain is no fun and it is dangerous. Always
seek shelter in an electrical storm. In extreme-
ly dry mowing conditions, your safety glasses
can serve a dual purpose by protecting your
eyes from dust and thrown objects, also a dust
or pollen mask can be helpful.
stitutions as service parts. If you need profes-
sional service, select a shop that is an
Authorized Service Center for your brand of
mower. If you plan to service the unit yourself,
follow directions in the Instruction Book.
Your mower is equipped with a number of safe-
ty features which are important to the safety of
the operator and bystanders and must never
be altered or removed. If a safety feature be-
comes inoperable, lost, or damaged, it must be
repaired or replaced before the mower is used.
Engine speed is a key to safe mowing and a
nice looking lawn. The maximum speed of the
engine on your mower has been set at the fac-
tory. Do not change the engine governor in any
way.
Select the maximum engine and ground speed
that is right for the terrain and the height of
grass. You get the best cutting and bagging
performance when using a grass catcher by
operating the engine at maximum speed. Nev-
er walk fast or run just to get the job done soon-
er. On inclines, reduce ground speed and
exercise extreme care.
As you mow, remember children and pets are
sometimes attracted to the activity. Be espe-
cially careful when trimming around shrubbery
or when backing up. If at all possible, don’t
mow when moving backwards. It is dangerous
because vision is restricted. Also, blades are
designed to cut while the unit is moving for-
ward so cutting performance is reduced when
mowing in reverse.
Never leave the mower running and unat-
tended. Shut off the engine. Put the mower in
a position so that it can not roll. If the unit is
self-propelled, make sure the drive control is
disengaged.
It is best to mow only during daylight hours;
however, if you must mow in the late afternoon
or evening, make sure there is good artificial
light.
Your mower will require maintenance including
service and adjustments before and after use
as with any machine. The frequency of the
maintenance is generally based on hours of
use, however, the frequency can vary because
of mowing conditions. Check the Instruction
Book for more detailed instructions. Proper
maintenance protects your investment in the
mower and helps insure that it will function
safely and reliably.
Never attempt any
service (with the pos-
sible exception of car-
buretor adjustment)
with the engine run-
ning. After turning the
engine off, always
disconnect the spark
plug wire to prevent
accidental restarting
while the unit is being
serviced.
When mowing, be aware of your condition and
the weather conditions. After mowing a long
time, you will be tired. This is the time when
reactions slow down, your attention wanders;
the time when you are wide open for an acci-
dent. Take a short break. If temperatures are
high, take precautions to avoid becoming de-
hydrated. If you are angry, tired, or unable to
give your full attention to mowing, if you have
been consuming alcohol, medicines, or drugs,
do not use your mower or any type of power
equipment.
If weather conditions become worse while you
are cutting, stop and finish later. Cutting grass
F-040411L
8
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFE MOWING GUIDE
While mowing, if you hit a foreign object, stop
position when mowing and bagging. When
bagging, slower ground speed will provide the
best results.
the engine. Remove the spark plug wire. Care-
fully and thoroughly inspect the mower for
damage. Make necessary repairs before re-
starting. If the unit starts to vibrate abnormally,
stop the engine immediately and check for the
cause. Vibration is generally a warning of
trouble. Keep all nuts, bolts, and screws tight.
Change the mowing pattern slightly each time
you cut. If you always cut the same way, the
grass will develop a “set” and clippings will ac-
cumulate more heavily in some areas more
than in others causing grass to get thinner in
those areas. Do not service your mower over
the grass. Spilled oil and gas can kill the grass.
In tall grass or very heavy grass, do not try to
cut it all at once. Raise the height of cut on the
first cutting and lower it for the next cutting the
same day or within a few days. Another way is
to cut only part of the width of the mower and
adjust your ground speed (not the engine) to
move more slowly so the mower can clear it-
self as it moves forward.
The blade is the most dangerous part of the
mower and also the most important part in ob-
taining a nice lawn appearance. Check the
blade and the blade mounting hardware fre-
quently. Keep it tight. If the blade hits a solid
object, check it thoroughly for deformation or
cracks and replace if damaged. For safety,re-
place the blade every two years. A sharp blade
reduces the work load on the engine and cuts
grass more cleanly, for a better looking cut with
less work. The blade is always close to the out-
side of the mower housing. For best trimming
on side discharge mowers, cut with the left
side of the housing toward the area that needs
trimming.
A useful accessory for your mower is a grass
catcher. There are grass catchers available for
most models. For best performance and safe-
ty, be sure the grass catcher is approved for
use with your mower. Assemble as directed
and follow operating and safety instructions
with the catcher and in the Instruction Book.
Before mounting, checking or emptying the
grass catcher, always turn the engine off. Re-
member to check the grass catcher before
each use for cracks, wear, or deterioration. Re-
place any part that is damaged with the man-
ufacturer’s recommended replacement part
before using the grass catcher again.
When cutting with a walk behind mower, al-
ways push the unit. Do not pull it. Pushing the
unit keeps the operator behind the mower in
the “operator’s zone” for better control. Push-
ing the unit also gives you a chance to see ex-
actly where and what you are mowing. There
will be times while you are mowing that you will
have to pull the mower backwards (such as
when the front of the mower has come up
against a wall or fence). If you must back up,
make sure your feet are in the clear. Stand well
back from the mower, plant your feet firmly with
each step and back up being careful to look be-
hind you. Resume normal mowing as soon as
possible.
If your unit is self-propelled, remember that
the drive mechanism is not designed to do all
the work, but the unit can move without your
help. Always keep your hands on the handle
near the controls when the engine is running.
Remember too that the self-propelled mecha-
nism can be dangerous. Keep hands and feet
away from belts and chains. Always turn off the
engine before attempting to remove anything
that becomes entangled in the self-propelled
system.
Proper cutting technique is important if you
want your lawn to look good. Avoid the tempta-
tion to cut grass too short. Cutting grass too
short can kill the plant, cause grass to turn yel-
low, or make the lawn look brown and thatchy.
Use the lower cutting heights in cool months
when the grass is lush. Use the higher cutting
heights in extremely dry periods. Cutting with
a dull blade or low engine speed bruises,
shreds, and can uproot some grass making
the lawn look dull and brown a few days after
cutting. Always put the throttle control in FAST
F-040411L
Remember, your mower is a useful tool, but it
can be dangerous. Follow the instructions in
this Instruction Book. Use the mower properly
and carefully and it will give you many hours of
trouble free, accident free operations.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
STEPS TO FOLLOW
BEFORE MOWING
D
Be sure to dress correctly. Wear hard shoes, not sandals or tennis shoes.
Examine the blade. A blade that is bent, cracked, or damaged must be replaced with a factory
replacement blade.
D
D
D
Fill the fuel tank outside. Clean off spilled fuel.
Read and follow the Owner’s Manual, the instructions with the engine, and the instructions with
any attachments. Owner’s Manual instructions are for your safety and the safety of others.
D
D
D
D
D
D
D
Exhaust fumes are dangerous. Start the engine outside.
Make sure all safety devices are in place and working correctly.
Operation of the mower is only for a person that has experience.
Wet grass can be dangerous. Let the grass dry.
Instruct children and others to keep away from the work area.
Never cut the grass without good light.
Pick up loose objects. Remove them from the mowing area.
WHILE MOWING
D
Watch for fixed objects and avoid them. They can damage the mower or cause injury.
A hot engine and muffler will cause a burn. Do not touch.
Inclines and slopes must be carefully mowed. See the “Guide” in the back of this book to check
a slope.
D
D
D
D
Lack of daylight or good artificial light is cause to stop mowing.
Examine the mower, the blade, and other parts for damage after hitting a foreign object or if the
unit vibrates excessively.
D
Do not make adjustments or repairs without stopping the engine (except for carburetor). Dis-
connect the spark plug wire.
D
On or near roads, watch out for traffic. Direct discharge away from roads.
When mowing, avoid areas where traction is unsure. Before and while moving backwards, look
behind and down for small children.
D
D
In heavy grass, raise the cutting height. Cut slower. Stop the engine to remove clogged grass
from the mower.
D
Never remove any safety related parts.
Do not pour gasoline into a engine that is hot or running.
D
AFTER MOWING
D
Always let the mower cool before storing in an enclosed area.
Foreign material on the mower is dangerous. Clean off grass, leaves, grease and oil before
storing.
D
D
D
D
D
D
D
D
D
Tighten all loose nuts, bolts and screws before you use the unit.
Empty and clean any grass catcher or other accessory.
Remove the key or disconnect the spark plug wire to prevent unauthorized use.
Make sure the mower is not kept near a source of ignition. Gas fumes can cause an explosion.
Only original parts or factory approved substitutes can be used to service the mower.
When storing the mower for an extended period, remove the fuel from the fuel tank.
Instruct children to leave the mower alone. It is not a toy.
Never keep gasoline near a source of ignition. Always use an approved container. Keep
gasoline away from children.
D
Lubricate according to the Instruction Book. See “Lubrication”.
IMPORTANT--Read the Instruction Book. Keep this book for future use and
reference.
WARNING: Look for this symbol to point out important
safety precautions. It means: “Attention! Become
Alert! Your Safety Is Involved.”
10
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
UNPACKING INSTRUCTIONS
The mower was fully assembled at the factory.
When the mower was put in the carton, the
handle was put in the storage position. To put
the handle in the operating position, follow the
steps below.
Upper Handle
Lower Handle
Knob
Handle
1. Remove the mower from the carton.
Knob
2. Put the lower handle in the operating posi-
tion. Make sure the lower handle is be-
tween the locking tabs (Figure 1).
Figure 1
3. Put the upper handle in the operating
position. Tighten the knobs.
CAUTION: Be careful when you fold or
raise the handle. Do not damage the
cables. A cable that is bent will not work
correctly. Before you use the unit, re-
place a bent or damaged cable.
Recoil-Start
Grip
4. To attach the recoil-start grip to the rope
guide, twist the rope through the rope
guide mounted on the right side of the han-
dle (Figure 2).
Rope
Guide
NOTE: If you cannot attach the
recoil-start grip because the rope is too
short, hold the engine stop lever
against the handle. Slowly pull the
recoil-start grip.
Figure 2
11
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
PREPARATION
HOW TO ADJUST THE HANDLE HEIGHT
Upper Handle
The handle bracket has two assembly posi-
tions. A HIGH and a LOW position (Figure 3).
The HIGH position will raise the handle ap-
proximately four inches.
Knob
Lower
Handle
HIGH
LOW
Bolt
Knob
Handle
Bracket
Figure 3
Figure 4
1. Remove the knobs and bolts from the
HIGH Position
right and left handle brackets (Figure 4).
Handle
Bracket
2. To raise the handle, mount the lower han-
dle in the HIGH position shown in Figure 5.
3. To lower the handle, mount the lower han-
dle in the LOW position shown in Figure 6.
Figure 5
LOW Position
4. Attach the lower handle to the handle
brackets with the bolts and knobs.
(Figure 4).
Handle
Bracket
Figure 6
12
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
PREPARATION
MODELS WITH OPTIONAL GRASS BAG
HOW TO ASSEMBLE THE GRASS BAG
Support Tube
1. Slide the frame assembly into the ends of
the support tube (Figure 7).
Frame Assembly
Figure 7
2. Make sure the handle is on the outside of
Handle
the grass bag (Figure 8).
Frame
Assembly
Clips
3. Attach the clips to the frame assembly
Figure 8
(Figure 8).
Top
Cover
4. Close the top cover. When operating the
mower with the grass bag, the top cover
must be in the closed operating position
(Figure 9).
Figure 9
13
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
PREPARATION
MODELS WITH OPTIONAL GRASS BAG
IMPORTANT: Make sure the hooks, on each
side of the frame assembly, are mounted
on the pivot rod.
HOW TO MOUNT
THE GRASS BAG
1. To mount the grass bag on the mower,
raise the rear door. Hold the handle of the
grass bag. Put the grass bag in the
operating position (Figure 10). Lower the
rear door.
WARNING: Do not use the grass
bag unless the cover is in the op-
erating postion.
Handle
Rear Door
Mount Frame
Hooks To Pivot Rod
Handle Bracket
Figure 10
HOW TO EMPTY THE GRASS BAG
WARNING: Before you remove
the grass bag, stop the engine.
Before you remove any grass
from the mower housing,
disconnect the wire from the
spark plug.
Grass Bag
1. Hold the rear door. Raise the rear door to
a vertical position (Figure 10).
2. Lift the frame assembly over the two
handle notches.
3. Open the top cover (Figure 11). Empty the
Top Cover
Figure 11
grass from the grass bag.
4. To mount the grass bag on the mower, see
“How To Mount The Grass Bag”.
F-040411L
14
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
HOW TO ATTACH THE SIDE MOUNTED
DISCHARGE DEFLECTOR
Mulcher Cover
WARNING: To prevent the en-
gine from starting, disconnect
the wire from the spark plug.
1. Raise the mulcher cover (Figure 12).
2. Slide the two tabs on the side deflector un-
der the pivot pin.
3. Lower the side deflector. Make sure the
locking tab goes through the slot in the side
deflector (Figure 13).
Side Deflector
Locking Tab
4. Lower the mulcher cover (Figure 14).
Figure 13
Mulcher Cover
Mulcher Cover
Side Deflector
Side Deflector
Tabs
Figure 12
Figure 14
S
S
Keep a sharp edge on the blade. A blade
that is not sharp will cause the ends of the
grass to become brown.
Clean the underside of the mower housing.
Grass and other debris can keep the mow-
er from working correctly.
MULCHING TIPS
Mulching finely cuts the grass so that the grass
can be easily recycled. Because the nutrients
are returned to the soil, the lawn will need less
fertilizer. To correctly mulch the lawn, follow
the tips below.
S
The grass must be dry. If the grass is wet,
it will be difficult to cut and cause heavy
clumps of grass.
The grass must not be too tall. The maxi-
mum height to effectively cut is 4 1/2 in-
ches. Set the height adjusters so that only
the top third of the grass is cut.
If the grass is more than 4 1/2 inches high,
two mowings will be necessary. For the first
mowing, set the height adjusters in the
highest position. Then, lower the height ad-
justers for the second mowing.
If the quality of cut is marginal, try the
following:
S
Set the height adjusters at a higher cutting
height.
S
S
S
S
Cut the grass more frequently.
Operate the mower at a slower ground
speed.
S
S
Overlap the cutting swaths instead of cut-
ting a full swath with each pass.
Mow across the marginal areas a second
time.
15
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
PREPARATION
ELECTRIC START MODELS
When the mower was shipped from the facto-
ry, the battery was not fully charged. Before the
first use, the battery must be charged for 16
hours. See “How To Charge The Battery” in the
Maintenance section.
ENGINE TIPPING
HOW TO PREPARE THE ENGINE
ENGINE DOES NOT CONTAIN
OIL OR GASOLINE
When you service the engine, inspect the
blade, or clean the underside of the mower
housing; make sure to always tip the engine
with the spark plug up (see Figure 15). Trans-
porting or tipping the engine with the spark
plug down will cause:
See the engine manufacturer’s instructions for
the type of gasoline and oil to use. Before you
use the unit, read the information on safety, op-
eration, maintenance, and storage.
WARNING: Follow the engine
manufacturer’s instructions for
the type of gasoline and oil to
use. Always use a safety gaso-
line container. Do not smoke
when adding gasoline to the en-
gine. When inside an enclosure,
do not fill with gasoline. Before
you add gasoline, stop the
engine. Let the engine cool for
several minutes.
S
S
S
S
Hard starting.
Engine smoking.
Spark plug fouling.
Oil or gas saturation of the air filter.
IMPORTANT: This unit is equipped with an
internal combustion engine and must not
be used on or near any unimproved forest-
covered, brush-covered or grass-covered
land unless the engine’s exhaust system is
equipped with a spark arrester meeting
applicable local or state laws (if any). If a
spark arrester is used, it must be main-
tained in effective working order by the op-
erator.
In the State of California the above is re-
quired by law (Section 4442 of the Califor-
nia Public Resources Code). Other states
may have similar laws. Federal laws apply
on federal lands. See an Authorized Ser-
vice Center for a spark arrester for the
muffler.
Figure 15
IMPORTANT: Actual sustained horsepow-
er will likely be lower due to operating limi-
tations and environmental factory.
FINAL ASSEMBLY
Before you use the mower, check the assem-
bly of the wheels, the handle, and the controls.
Make sure all the fasteners are tight. Make
sure the throttle control and the engine stop le-
ver work correctly.
16
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
ENGINE STOP LEVER
WARNING: For safe operation,
the drive system must immedi-
ately disengage when the drive
lever is released. If the drive
system does not disengage
correctly, do not operate the
mower until the drive system is
adjusted or repaired by an
authorized service center.
Release the engine stop lever and the engine
and the blade will automatically stop. To run
the engine, hold the engine stop lever in the
Operating position (Figure 17).
Before you start the engine, operate the en-
gine stop lever several times. Make sure the
cable moves easily.
Operating Position
Drive Lever
Engine Stop
Lever
Hold the engine stop lever
in the Operating position.
Figure 16
FRONT WHEEL DRIVE SYSTEM
The mower has a front wheel drive system.
Operate the drive system as follows.
To go forward, move the
drive lever forward.
Figure 17
1. Hold the engine stop lever in the Operat-
ing Position (Figure 16 and Figure 17).
2. Push the drive lever completely forward.
When the drive lever clicks, release the
drive lever. The drive system is now en-
gaged.
HOW TO STOP THE ENGINE
NOTE: To stop the engine, release the
engine stop lever.
To stop the engine, release the engine stop
lever. Disconnect the wire from the spark plug
to prevent the engine from starting. On models
equipped with an electric start engine, remove
the key from the key switch. Keep the key
away from children.
3. To disengage the drive system and stop
the engine, completely release the engine
stop lever.
4. To disengage only the drive system, re-
lease the engine stop lever approximate-
ly two inches. The drive system will
disengage but the engine will continue to
run.
NOTE: When the drive system is
disengaged on a new unit, it is possible for
the front wheels to rotate if lifted off the
ground. This is normal and will stop after
If the engine will not stop, hold a screwdriver
against the spark plug and against the engine
cooling fins. The spark will go to ground and
the engine will stop. Before you start the en-
gine, check the engine stop cable. Make sure
the engine stop cable is assembled correctly.
Before you operate the unit, replace a bent or
damaged engine stop cable.
one or two hours of operation.
F-040411L
17
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING: To prevent an acci-
dent, make sure the drive lever is
in the DISENGAGED position.
When the drive lever is in the EN-
GAGED position, do not start the
engine.
HOW TO START ENGINE
WARNING: The blade will rotate
when the engine runs.
IMPORTANT: Before you start the engine,
operate the engine stop lever several
times. Make sure the engine stop cable
moves freely.
6. Some models have a primer button on the
front or side of the engine (Figure 19). Ev-
ery time you push the primer button, wait
two seconds. For the number of times re-
quired to push the primer button, see the
engine manufacturer’s instructions.
NOTE: The engine design does not include
a throttle control or an engine speed ad-
justment. The engine is set at the best
speed for cutting grass, bagging grass,
and for extended engine life.
1. Check the oil.
2. Fill the fuel tank with regular unleaded gas-
oline. Make sure the gasoline is clean.
Leaded gasoline will increase deposits and
shorten the life of the valves.
NOTE: Do not use gasohol or methanol. Do
not use premium unleaded gasoline.
Primer Button
Figure 19
WARNING: Always use a safety
gasoline container. Do not smoke
when adding gasoline to the fuel
tank. When inside an enclosure,
do not add gasoline. Before you
add gasoline, stop the engine and
let the engine cool for several
minutes.
NOTE: Do not use the primer button to
start a warm engine.
7. Stand behind the mower. Hold the engine
stop lever in the OPERATING position
(Figure 18).
8. Electric Start Models: Turn the ignition
key to the START position. Use short start-
ing cycles (15 seconds per minute). When
the engine starts, release the ignition key.
If the engine will not turn over, charge the
battery. See “How To Charge The Battery”.
3. Make sure the spark plug wire is connected
to the spark plug.
4. Electric Start Models: Make sure the bat-
tery is connected to the wiring harness.
5. Make sure the drive lever is in the DISEN-
9. Recoil-Start Models: Rapidly pull the re-
coil-start grip. Slowly return the recoil-
start grip.
GAGED position (Figure 18).
10. If the engine does not start in 5 or 6 tries,
See the “Problem and Repair” Instructions.
Hold the engine stop lever
in the operating position.
HOW TO OPERATE THE MOWER
WARNING: Check the condition
of the grass bag for wear or dete-
rioration. If worn or damaged, re-
place the parts only with ap-
proved factory replacement
parts. For replacement parts,
see the parts list in this book.
Drive Lever
Ignition Key
To completely fill the grass bag, operate the
engine with the throttle control in the FAST
position.
Figure 18
18
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
4. Charge the battery for 16 hours.
ELECTRIC START MODELS
5. Disconnect the battery charger from the
electrical outlet and from the battery.
HOW TO CHARGE THE BATTERY
WARNING: The battery contains
sulfuric acid which is harmful to
the skin, eyes and clothing. If
acid gets on the body or cloth-
ing, wash with water. Do not at-
tempt to open the battery. If the
battery has a crack, replace the
battery. Do not burn a damaged
or old battery or an explosion
can result.
6. Align the two tabs on the bottom of the bat-
tery case with the two holes in the battery
bracket. Rotate the battery case until the
quick release locks the battery in the OP-
ERATING position.
7. Connect the wiring harness to the bat-
tery. If the battery will not be used for a long
period of time or during storage, do not
connect the wiring harness to the battery.
WARNING: When you charge the
battery, do not smoke. Keep the
battery away from any sparks.
The fumes from the battery acid
can cause an explosion.
Handle
Battery Bracket
The battery is in the battery case mounted on
the handle. To charge the battery, remove the
battery case from the handle.
IMPORTANT: Make sure to use the battery
charger supplied with the mower. The use
of any other battery charger will damage
the battery.
Quick Release
1. Disconnect the wiring harness from the
battery (Figure 20).
2. Push the quick release on top of the bat-
tery case. Remove the battery case and
battery from the handle.
3. Attach the battery charger wire to the
battery. Connect the battery charger to an
electrical outlet.
Battery Case
Wiring Harness
Battery Charger Wire
Figure 20
HOW TO REMOVE THE BATTERY
Screw
If the engine will not turn over or turns over
slowly when the key is turned on, charge the
battery. See “How To Charge The Battery”. If
the battery will not charge fully and will not start
the engine, replace the battery as follows.
Battery Case
1. Disconnect the wiring harness from the
battery (Figure 20).
2. Push the quick release on top of the bat-
tery case. Remove the battery case and
battery from the handle.
Battery
3. To open the battery case, remove the
three screws. Remove the battery from
the battery case (Figure 21).
4. Replace the battery with an authorized
factory replacement battery.
5. Charge the new battery for 16 hours. See
“How To Charge The Battery”.
6. To install the battery, reverse the above
steps.
F-040411L
Battery Case
Figure 21
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
ENGINE MAINTENANCE
Use the following maintenance section to keep
your unit in good operating condition. All the
maintenance information for the engine is in
the “Engine Instruction Book”. Before you start
the engine, read this book.
S
S
S
S
Hard starting.
Engine smoking.
Spark plug fouling.
Oil or gas saturation of the air filter.
WARNING: Before you make an
inspection, adjustment (except
carburetor), or repair, stop the
engine and disconnect the wire
from the spark plug.
ENGINE TIPPING
When you service the engine, inspect the
blade, or clean the underside of the mower
housing; make sure to always tip the engine
with the spark plug up (see Figure 22). Trans-
porting or tipping the engine with the spark
plug down will cause:
Figure 22
HOW TO CLEAN
THE MOWER HOUSING
HOW TO ADJUST
THE HEIGHT OF CUT
WARNING: The blade will rotate
when the engine runs. Before
you change the height of cut,
stop the engine and disconnect
the wire from the spark plug.
WARNING: The blade will rotate
when the engine runs. Before
you clean the mower housing,
stop the engine and disconnect
the wire from the spark plug.
To change the height of cut, move the position
of the adjuster arm at each wheel (Figure 23).
Make sure each adjuster arm is in the same
position so that the mower will cut level.
Grass and other debris can keep the mower
from working correctly. After you mow, clean
the mower housing as follows.
1. Stop the engine.
1. Disengage the adjuster arm.
2. Move the adjuster arm to another posi-
2. Disconnect the wire from the spark plug.
tion.
3. Clean the top and the bottom of the mower
housing.
Adjuster
Arm
LUBRICATION
1. For maximum performance, lubricate the
wheels and all pivot points with engine oil
every 25 hours.
2. To lubricate the engine, refer to the “En-
gine Instruction Book”.
NOTE: Do not lubricate the engine stop
cable. Lubricants will damage the cable
and prevent the cable from moving freely.
Replace the cable if bent or damaged.
F-040411L
Figure 23
20
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
HOW TO REMOVE THE DRIVE BELT
Transmission
Belt Tension Bolt
Pulley
WARNING: Before you remove
the belt, disconnect the wire
from the spark plug.
1. Remove the belt cover (Figure 24).
2. Loosen the belt tension bolt (Figure 25).
3. Remove the front of the drive belt from
the transmission pulley.
4. To remove the rear of the drive belt, slip
the drive belt over the end of the blade
(Figure 26).
NOTE: Make sure you replace the drive
belt only with a replacement belt from
the factory.
Drive Belt
5. To assemble the drive belt, reverse the
Figure 25
above steps.
6. Set the belt tension.
a. Tighten the adjuster nut until the nut
touches the spacer (Figure 27). Try to
turn the spacer. When the adjuster
nut touches the spacer, the spacer
will not turn.
b. Then, loosen the adjuster nut only
enough to allow the spacer to turn.
The tension on the drive belt is now
correct.
7. Install the belt cover (Figure 24).
8. Before you begin to mow, make sure the
drive system will correctly disengage and
that the mower will stop. If the drive system
will not disengage, take the mower to an
authorized service center before you op-
erate the mower.
Blade
Belt Tension Bolt
Figure 26
Belt Cover
Spacer
Adjuster
Nut
Figure 24
Figure 27
21
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
MAINTENANCE
HOW TO ADJUST THE DRIVE CABLE
WARNING: Before you adjust the
drive cable, release the engine
stop lever and wait for the engine
to stop.
NOTE: The engine design does not include
a throttle control or an engine speed ad-
justment. The engine is set at the best
speed for cutting grass, bagging grass,
and for extended engine life.
If the drive system does not engage and disen-
gage correctly, check the handle for correct as-
sembly. Make sure that all parts are in good
condition, not broken or bent, and that all fas-
teners are tight.
1. If the drive system is slipping, turn the
cable adjuster one turn in the direction
shown in Figure 28. Test the drive system
and check for slippage.
2. If the drive system still slips, turn the cable
adjuster one more turn to shorten the
cable. Again, test the drive system.
Worn parts and cable stretch will change the
performance of the drive system. When you
mow in high or thick grass or on hills, the drive
system can slip. If the drive system is slipping,
adjust as follows or take the mower to an au-
thorized service center.
3. Repeat the adjustment and test until the
drive system does not slip.
4. Before you begin to mow, make sure the
drive system will correctly disengage and
that the mower will stop. If the drive system
will not disengage, take the mower to an
authorized service center before you oper-
ate the mower.
IMPORTANT: Before you start the engine,
operate the engine stop lever several
times. Make sure the engine stop cable
moves freely.
Figure 28
Cable Adjuster
22
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
BLADE SERVICE
WARNING: Before you inspect
the blade or the blade adapter,
disconnect the wire to the spark
plug. If the blade hits an object,
stop the engine. Disconnect the
wire to the spark plug. Check the
unit for damage.
Blade Adapter
Blade Adapter
Blade
Belleville
Frequently check the blade for wear or dam-
age such as cracks. Frequently check the bolt
that holds the blade. Keep the bolt tight. If the
blade hits an object, stop the engine. Discon-
nect the wire to the spark plug. Check the
blade adapter for damage. Check for a bent or
damaged blade, a badly worn blade, or other
damage. Before you operate the unit, dam-
aged parts must be replaced with factory re-
placement parts. For safety, replace the blade
every two years. Keep a sharp edge on the
blade. A blade that is not sharp will cause the
ends of the grass to become brown. Remove
the blade as follows.
Washer
Washer
Bolt
Mulching Blade
Belleville Washer
Flat Washer
Figure 29
Bolt
HOW TO REMOVE THE BLADE
WARNING: Before you remove
the blade, disconnect the wire to
the spark plug. The blade has
sharp edges. When you hold the
blade, use gloves or cloth materi-
al to protect your hands.
HOW TO SHARPEN THE BLADE
WARNING: Vibration is the result
if the blade is not correctly bal-
anced. A blade that is damaged
with cracks can break and cause
an accident.
1. Drain the fuel tank.
2. Lift the side of the mower that has the
muffler or spark plug.
3. Use a piece of wood to keep the blade
from rotating.
1. Sharpen the blade two times a year or ev-
ery 25 hours.
2. If the blade is on the unit, do not sharpen.
Remove the blade according to the in-
structions in “How To Remove The Blade”.
4. Remove the bolt that holds the blade.
5. Check the blade according to the “Blade
Service” instructions. Replace a badly
worn or damaged blade with a factory re-
placement blade.
6. Mount the blade with the curved edges to-
ward the housing. If the blade is upside
down, the blade will not cut correctly and
can cause an accident.
3. Clean the blade with a brush, soap, and
water. Check the blade. Look for cracks,
nicks, or other damage. Replace a blade
that is badly worn, bent, or damaged with
a factory replacement blade.
4. Sharpen the blade with a file. Make sure
you keep the original beveled cutting edge
(Figure 30).
5. Make sure the blade is balanced. Use a
screwdriver and hold the blade parallel to
the ground as shown. A blade that is bal-
anced will stay parallel to the ground. If the
blade is not balanced, the heavy end will
rotate toward the ground. Sharpen the
heavy end until the blade is balanced.
7. Fasten the blade with the original wash-
ers and bolt. Make sure the outside rims
of the Belleville washers are toward the
blade (Figure 29).
8. Tighten the bolt that holds the blade to a
torque of 30 foot pounds.
6. A new blade will cut better than a badly
worn blade. Every two years replace the
old blade with a factory replacement
blade.
WARNING: Always keep the bolt
that holds the blade tight. A loose
bolt or blade can cause an acci-
dent.
(Continued following page)
23
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
3. Rotate the handle forward over the engine
as shown. Make sure the cables are not
damaged.
Blade
Folding Handle
File
Screwdriver
Blade is balanced
when parallel to
the ground.
Ground
Figure 30
Figure 31
CHECK THE LEVEL OF CUT
How To Raise The Handle
Test the unit in a small area. If the height of cut
is not level or if the cut grass is not discharged,
the cause can be: (1) the blade is bent or dam-
aged, (2) the blade is not sharp, (3) a worn
blade, (4) or a broken blade adapter. Before
you use the unit, correct the problem.
1. Pull the handle back until the ends of the
lower handle lock into position. Tighten the
knobs.
2. Lift the upper part of the handle into the op-
erator’s position. Tighten the fasteners
that hold the handle.
STORAGE FOR HANDLES THAT FOLD
CAUTION: Be careful when you fold or
raise the handle. Do not damage the
cables. A cable that is bent will not work
correctly. Before you use the unit, replace a
bent or damaged cable.
STORAGE FOR
NON-FOLDING UPPER HANDLES
For storage, fold the handle forward.
How To Fold The Handle
How To Fold The Handle
1. Push in on the ends of the lower handle.
Move the ends of the lower handle past the
locking tabs.
2. Rotate the handle forward over the en-
gine. Make sure the cables are not dam-
aged.
1. Loosen the fasteners that hold the upper
part of the handle to the lower part of the
handle. As you fold the handle, make sure
the cables are not around the loose fasten-
ers and do not become damaged. Rotate
the upper part of the handle back
(Figure 31).
How To Raise The Handle
2. Loosen the knobs on the lower handle.
Push in on the ends of the lower handle.
1. Pull the handle back until the ends of the
lower handle lock into position.
Pour one ounce of oil into the cylinder.
Slowly pull the recoil-start grip so that the
oil will protect the cylinder. Install a new
spark plug in the cylinder.
HOW TO PREPARE
THE MOWER FOR STORAGE
WARNING: Do not remove gaso-
line while inside a building, near
5. Clean the dirt and debris from the cylinder
cooling fins and the engine housing.
6. Clean the bottom of the mower housing.
7. Make sure the grass bag is empty of grass.
Grass remaining in the bag during storage
will damage the bag.
8. Completely clean the mower to protect the
paint.
9. Put the unit in a building that has good ven-
tilation.
a
fire, or while you smoke.
Gasoline fumes can cause an
explosion or a fire.
1. Drain the fuel tank.
2. Let the engine run until it is out of gasoline.
3. Drain the oil from the warm engine. Fill the
engine crankcase with new oil.
4. Remove the spark plug from the cylinder.
F-040411L
24
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLE SHOOTING CHART
The Engine will not start.
1. Move the throttle control lever to the FAST or START position.
2. Make sure the fuel tank is filled with clean gasoline. Do not use old gasoline.
3. On a cold engine, push the primer button (optional on some models) five times.
4. Make sure the wire for the spark plug is connected to the spark plug.
5. Adjust the Carburetor. See the “Engine Instruction Book”.
6. There is too much gasoline in the engine cylinder. Remove and dry the spark plug. Put the
throttle control in the SLOW position. Pull the recoil-start grip several times. Install the spark
plug. Connect the wire to the spark plug. Start the engine.
7. The engine is difficult to start in heavy or high grass. Move the mower to a clean dry surface.
8. Make sure the engine stop lever is in the operating position.
9. Make sure the fuel valve is in the ON position. See the “Engine Instruction Book”.
10. On electric start models, make sure the wiring harness is connected. Charge the battery.
The Engine will not stop.
1. Release the engine stop lever.
2. Check the engine stop cable. Replace the cable if bent or damaged.
The Engine performance is bad.
1. Check the height of cut settings. Raise the height of cut if the grass is high.
2. Check the bottom of the blade housing. Clean the blade housing of grass and other debris.
3. Check the wire to the spark plug. Make sure the wire is connected.
4. Clean the engine cooling fins of grass and other debris.
5. Check the carburetor adjustments. See the “Engine Instruction Book”.
6. Check the spark plug gap. Set the spark plug gap at 0.030”.
7. Check the amount of oil in the engine. Fill with oil if necessary.
8. Check the engine air cleaner. See the “Engine Instruction Book”.
9. The gasoline is bad. Drain and clean the fuel tank. Fill the fuel tank with clean gasoline.
10. Check the throttle control. Make sure the lever is not in the CHOKE position.
Excessive Vibration.
1. Remove the blade. Check the blade and balance if necessary. See the blade maintenance
instructions.
2. Check for a bent or broken blade. A DAMAGED BLADE IS DANGEROUS AND MUST BE
REPLACED.
3. Check the blade adapter. REPLACE A BROKEN BLADE ADAPTER.
4. If the vibration continues, take the mower to an Authorized Service Center.
The grass will not discharge correctly.
1. Clean the bottom of the mower housing.
2. Check for a badly worn blade. Remove and sharpen the blade. For safety, replace the blade
every two years with a factory replacement blade.
3. Move the throttle control lever to the FAST position. Check the speed of the engine according
to the “Engine Instruction Book”.
The grass is not cut even.
1. Check the height adjustment at each wheel. The height adjustment must be the same for each
wheel.
2. Make sure the blade is sharp.
3. Check for a bent or broken blade. A DAMAGED BLADE IS DANGEROUS AND MUST BE
REPLACED.
4. Check for a broken blade adapter. REPLACE A BROKEN BLADE ADAPTER.
25
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
26
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
27
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
MULCHER MODELS
2
5
6
8
3
29
4
59
60
28
58
30
24
57
50
31
59
61
23
62
26
7
52
53
54
14
50
51
25
55
49
29
48
1
31
11
12
13
44
46
24
10
23
30
45
42
37
34
25
38
39
34
32
40
41
43
44
28
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
MULCHER MODELS
KEY
NO. PART NO.
KEY
NO. PART NO.
DESCRIPTION
DESCRIPTION
1
2
3
4
1101340E717 Housing
37 043629
Pin, Drive
− − − − −
1101653
Engine *
38 1101120E701 Blade
Pulley, Drive
39 17x137
40 17x124
41 01x144
42 1101336
Washer, Belleville
1101331
1101332
Spacer, Engine (Black)
Spacer, Engine (Gray)
Washer
Bolt
5
1101596
1101568
Cover, Belt (Black)
Cover, Belt (Gray)
Adapter, Blade
43 672915E700 Baffle, Front **
6
7
26x304
672605
Screw
44 015x68
45 1101028
Nut, Flange
Adjuster, Left Rear
Height
Adjuster, Right Front
Height
8
26x303
Screw
46 001x85
Bolt
10 1101571
Transmission − Note:
There are no internal
serviceable parts for
the transmission.
48 672916E700 Baffle, Rear **
49 672604
Adjuster, Right Rear
Height
11 043844
12 164x27
13 015x88
14 01x156
23 011x16
24 17x186
25 071792
26 1101029
Spacer
50 028x49
Retainer, Push
Spring, Compression
Nut
51 1101238E701 Bracket, Right Handle
52 015x79
53 001x45
Nut, Flange
Bolt
Bolt
E−Ring
54 1101239E701 Bracket, Left Handle
Washer
55 025x11
57 215x21
Bolt, Engine
Rod, Pivot
Gear, Pinion
Adjuster, Left Front
Height
58 672611
672713
Door, Rear (Black)
Door, Rear (Gray)
28 37x123
29 672122
30 015x84
31 17x169
32 071133
34 071780
Belt
59 26x245
60 166x44
61 1101105
62 071132
− − F−040411L
Screw
Cap, Hub
Spring
Nut, Flange
Washer
Guard, Rear
Wheel & Tire, Rear
Book, Instruction
Wheel & Tire, Front
Cover, Dust
*
Parts are available from an Authorized Engine Service Center. See ꢀEngines, Gasoline" or ꢀGasoline
Engines" in the yellow pages of the telephone directory.
* * Included with Housing, Key No. 1.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
SIDE DISCHARGE MODELS
2
5
6
8
3
4
29
59
60
28
58
30
24
50
57
31
59
61
23
62
26
7
52
53
54
14
50
51
25
55
49
29
48
1
31
11
12
13
44
68
46
24
67
10
23
30
45
42
37
34
66
25
69
67
38
39
34
32
70
40
41
43
44
30
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
SIDE DISCHARGE MODELS
KEY
NO. PART NO.
KEY
DESCRIPTION
NO. PART NO.
40 17x124
41 01x144
42 1101336
DESCRIPTION
Washer
1
2
3
4
1101340E717 Housing
− − − − −
1101653
Engine *
Bolt
Pulley, Drive
Adapter, Blade
1101331
1101332
Spacer, Engine (Black)
Spacer, Engine (Gray)
43 672915E700 Baffle, Front **
44 015x68
45 1101028
Nut, Flange
5
1101596
1101568
Cover, Belt (Black)
Cover, Belt (Gray)
Adjuster, Right Front
Height
6
7
26x304
672605
Screw
46 001x85
Bolt
Adjuster, Left Rear
Height
48 672916E700 Baffle, Rear **
49 672604
Adjuster, Right Rear
Height
8
26x303
Screw
10 1101571
Transmission − Note:
There are no internal
serviceable parts for
the transmission.
50 028x49
Retainer, Push
51 1101238E701 Bracket, Right Handle
52 015x79
53 001x45
Nut, Flange
Bolt
11 043844
12 164x27
13 15x88
Spacer
54 1101239E701 Bracket, Left Handle
Spring, Compression
Nut
55 025x11
57 215x21
Bolt, Engine
Rod, Pivot
14 01x156
23 011x16
24 17x186
25 071792
26 1101029
Bolt
58 672611
672613
Door, Rear (Black)
Door, Rear (Gray)
E−Ring
Washer
59 26x245
60 166x44
61 1101105
62 071132
Screw
Gear, Pinion
Spring
Adjuster, Left Front
Height
Guard, Rear
Wheel & Tire, Rear
28 37x123
29 672122
30 015x84
31 17x169
32 071133
34 071780
37 043629
Belt
66 1101097
672917
Deflector, Chute (Black)
Deflector, Chute (Gray)
Cap, Hub
Nut, Flange
Washer
67 028x42
68 215x19 Z
69 166x38
Push On Cap
Rod, Pivot
Wheel & Tire, Front
Cover, Dust
Pin, Drive
Spring, Torsion
70 1101098
672920
Cover, Mulch (Black)
Cover, Mulch (Gray)
38 1101120E701 Blade
39 17x137 Washer, Belleville
− − F−040411L
Book, Instruction
*
Parts are available from an Authorized Engine Service Center. See ꢀEngines, Gasoline" or ꢀGasoline
Engines" in the yellow pages of the telephone directory.
* * Included with Housing, Key No. 1.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
MULCHER MODELS WITH 14” REAR WHEELS
2
6
47
30
28
3
8
4
5
57
59
60
62
7
58
50
56
44
59
61
23
52
53
24
25
14
54
26
50
44
51
55
49
1
29
48
46
44
31
11
12
13
46
24
10
34
23
30
45
42
37
25
38
39
34
32
40
41
43
44
32
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
MULCHER MODELS WITH 14” REAR WHEELS
KEY
NO. PART NO.
KEY
NO. PART NO.
DESCRIPTION
Housing
DESCRIPTION
1
2
3
4
− − − − −
− − − − −
1101653
38 1101120E701 Blade
Engine *
39 17x137
40 17x124
41 01x144
42 1101336
Washer, Belleville
Pulley, Drive
Washer
Bolt
1101331
1101332
Spacer, Engine (Black)
Spacer, Engine (Gray)
Adapter, Blade
5
1101596
1101568
Cover, Belt (Black)
Cover, Belt (Gray)
43 672915E700 Baffle, Front * *
44 015x68
45 1101028
Nut, Flange
6
7
26x304
672919
Screw
Adjuster, Right Front
Height
Adjuster, Left Rear
Height
46 001x85
47 0020x3
Bolt
8
26x303
Screw
Washer
10 1101571
Transmission − Note:
There are no internal
serviceable parts for
the transmission.
48 672916E700 Baffle, Rear * *
49 672918
Adjuster, Right Rear
Height
50 028x49
Retainer, Push
11 043844
12 164x27
13 015x88
14 01x156
23 011x16
24 17x186
25 071792
26 1101029
Spacer
51 1101244E701 Bracket, Right Handle
Spring, Compression
Nut
52 015x68
53 001x85
Nut, Flange
Bolt
Bolt
54 1101245E701 Bracket, Left Handle
55 025x11 Bolt, Engine
56 1101008E701 Brace
E−Ring
Washer
Gear, Pinion
57 215x21
Rod, Pivot +
Adjuster, Left Front
Height
58 1101070
672613
Door, Rear (Black)
Door, Rear (Gray)
28 37x123
29 672122
30 015x84
31 17x169
32 071133
34 071780
37 043629
Belt
59 26x245
60 166x44
61 672684
62 071841
− − F−040411L
Screw
Cap, Hub
Spring +
Nut, Flange
Washer
Guard, Rear
Wheel & Tire, Rear
Book, Instruction
Wheel & Tire, Front
Cover, Dust
Pin, Drive
*
Parts are available from an Authorized Engine Service Center. See ꢀEngines, Gasoline" or ꢀGasoline
Engines" in the yellow pages of the telephone directory.
* * Included with Housing, Key No. 1.
Included with Key No. 58.
+
33
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
SIDE DISCHARGE MODELS WITH 14" REAR WHEELS
2
6
47
30
28
3
8
4
5
57
59
60
62
7
58
50
56
44
59
61
23
52
53
24
25
14
54
26
50
44
51
55
49
67
1
29
48
46
44
31
11
12
13
46
24
10
23
68
30
45
42
37
25
34
66
38
39
69
67
34
32
40
41
70
43
44
34
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
SIDE DISCHARGE MODELS WITH 14" REAR WHEELS
KEY
NO. PART NO.
KEY
NO. PART NO.
DESCRIPTION
DESCRIPTION
Bolt
1
2
3
4
1101340E717 Housing
41 01x144
42 1101336
− − − − −
1101653
Engine *
Adapter, Blade
Pulley, Drive
43 672915E700 Baffle, Front * *
44 015x68
45 1101028
Nut, Flange
1101331
1101332
Spacer, Engine (Black)
Spacer, Engine (Gray)
Adjuster, Right Front
Height
5
1101596
1101568
Cover, Belt (Black)
Cover, Belt (Gray)
46 001x85
47 0020x3
Bolt
6
7
26x304
672919
Screw
Washer
Adjuster, Left Rear
Height
48 672916E700 Baffle, Rear * *
49 672918
Adjuster, Right Rear
Height
8
26x303
Screw
10 1101571
Transmission − Note:
There are no internal
serviceable parts for
the transmission.
50 028x49
Retainer, Push
51 1101244E701 Bracket, Right Handle
52 015x68
53 001x85
Nut, Flange
Bolt
11 043844
12 164x27
13 015x88
14 01x156
23 011x16
24 17x186
25 071792
26 1101029
Spacer
54 1101245E701 Bracket, Left Handle
55 025x11 Bolt, Engine
56 1101008E701 Brace
Spring, Compression
Nut
Bolt
57 215x21
Rod, Pivot +
E−Ring
58 1101070
672613
Door, Rear (Black)
Door, Rear (Gray)
Washer
Gear, Pinion
59 26x245
60 166x44
61 672684
62 071841
Screw
Adjuster, Left Front
Height
Spring +
Guard, Rear
Wheel & Tire, Rear
28 37x123
29 672122
30 015x84
31 17x169
32 071133
34 071780
37 043629
Belt
Cap, Hub
66 1101097
672917
Deflector, Chute (Black)
Deflector, Chute (Gray)
Nut, Flange
Washer
67 028x42
68 215x19 Z
69 166x38
Push On Cap
Rod, Pivot
Wheel & Tire, Front
Cover, Dust
Pin, Drive
Spring, Torsion
70 1101098
672920
Cover, Mulch (Black)
Cover, Mulch (Gray)
38 1101120E701 Blade
39 17x137
40 17x124
Washer, Belleville
Washer
− − F−040411L
Book, Instruction
*
Parts are available from an Authorized Engine Service Center. See ꢀEngines, Gasoline" or ꢀGasoline
Engines" in the yellow pages of the telephone directory.
* * Included with Housing, Key No. 1.
+
Included with Key No. 58.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
HANDLE - RECOIL-START MODELS
1
3
4
8
5
5
12
6
16
13
2
7
31
29
KEY
NO. PART NO.
KEY
NO. PART NO.
DESCRIPTION
DESCRIPTION
1
1101557E701 Handle, Upper (Black)
1101557E724 Handle, Upper (Gray)
7
8
1101353
Fastener, Double Cable
1101076E701 Lever, Stop
2
672906E701 Handle, Lower (Black)
672906E724 Handle, Lower (Gray)
12 002x77
13 071294
16 071530
29 002x81
31 071495
Bolt
Knob
3
4
5
6
025x14
1101670
15x116
Bolt
Guide, Rope
Bolt, Carriage
Knob, Plastic
Control, Drive
Locknut
1101365
1101366
Cable, Stop (Briggs)
Cable, Stop, (Tecumseh)
36
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
HANDLE - ELECTRIC-START MODELS
1
27
17
18
3
4
8
20
21
22
5
23
5
10
12
6
16
24
13
26
11
25
2
7
31
29
KEY
NO. PART NO.
KEY
DESCRIPTION
NO. PART NO.
16 071530
17 091488
18 091489
20 1101602
21 776011
22 671992
23 250x110
24 776014
25 776013
DESCRIPTION
Guide, Rope
Cap
1
1101557E701 Handle, Upper (Black)
1101557E724 Handle, Upper (Gray)
2
672907E701 Handle, Lower (Black)
672907E724 Handle, Lower (Gray)
Nut
Cover, Ignition
Switch Ignition & Key
Charger, Battery
Harness, Wiring
Battery
3
4
5
6
025x14
1101670
15x116
Bolt
Control, Drive
Locknut
1101365
1101366
Cable, Stop (Briggs)
Cable, Stop (Tecumseh)
Case, Battery
7
8
1101353
Fastener, Double Cable
26 671959E701 Bracket, Battery
1101076E701 Lever, Stop
27 672220
29 002x81
31 071495
Key, Ignition
Bolt, Carriage
Knob, Plastic
10 26x220
11 071372
12 002x77
Screw
Fastener, Cable
Bolt
13 071294
Knob
37
Download from Www.Somanuals.com. All Manuals Search And Download.
F-040411L
GRASS BAG
1
3
2
KEY
NO.
DESCRIPTION
PART NO.
1101075
1101074
1101005
1
2
3
Tube, Bag
Frame Assembly
Bag, Cloth
38
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
39
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
HOW TO ORDER REPAIR PARTS
Only use a factory repair part. Repair parts, except for the engine or the transmission, are available from the store where
the unit was purchased, a service shop recommended by the store, or an authorized service shop found in the yellow
pages of the telephone directory. If you cannot get a repair part or service as described above, call or write to the Central
Parts Distributor shown below. When you order, include the following information: (1) Complete Model Number (see
nameplate), (2) Date of Manufacture, (3) Complete Part Number, (4) Description, (5) Quantity.
Repair parts for the engine or the transmission are available from the manufacturer’s authorized service center found
in the yellow pages of the telephone directory. See the individual engine or transmission warranties.
MURRAY, INC. LAWN MOWER CENTRAL PARTS DISTRIBUTORS
FRANK EDWARDS CO.
BILLIOU’S, INC.
GULF COAST ENGINE, INC.
1343 South Main St.
3626 Parkway Blvd.
4202 Russell Dr.
Porterville, CA. 93257
(559)784−4102ꢁ1−877−245−5468
FAX 1−800−266−7337
Arizona, California, Hawaii,
Nevada
West Valley City, UT 84120
1−800−318−0201
FAX (801)736−8067
Corpus Christi, TX. 78408
1−800−825−6999
FAX (888)888−7036
Arkansas (counties Hempstead,
Howard, Lafayette, Little River,
Miller, Nevada, Pike, Sevier) New
Mexico, Oklahoma, Texas,
Mexico
Colorado, Idaho (counties
Bannock Bearlake, Bingham,
Blaine, Booneville, Butte, Camas,
Caribou, Cassia, Custer, Franklin,
Fremont, Gooding, Jefferson,
Jerome, Lemhi, Lincoln, Madison,
Minidoka, Oneida, Power, Teton,
Twin Falls) Montana (all counties
except Flathead, Lake, Lincoln,
Mineral, Missoulo, Ravalli,
Sanders), Utah, Wyoming
BROWN & WISER, INC.
9991 S.W. Avery Street
Tualatin, OR. 97062
(503)692−0330ꢁ1−800−882−4782
FAX (503)691−2041
WISCONSIN MAGNETO
Alaska, Idaho (counties Ada,
Adams, Benewah, Boise, Bonner,
Boundry, Canyon, Clearwater,
Elmore, Gem, Idaho, Kooten,
Latah, Lewis, NEZ Perce, Owyee,
Payette, Ravalli, Shoshone, Valley,
Washington), Montana (counties
Flathead, Lake, Lincoln, Mineral,
Missoulo, Ravalli, Sanders),
Oregon, Washington
4727 N. Teutonia Ave.
Milwaukee, WI. 53209
1−800−733−7388
FAX 1−800−733−0127
Illinois (N. of Hwy. 80), Michigan
(upper Peninsula), Minnesota,
North Dakota, South Dakota,
Wisconsin
GARDNER, INC.
3641 Interchange Road
Columbus, OH. 43204−1499
1−800−848−8946
FAX 1−800−626−4735
Alabama, Arkansas, (except these
counties: Hempstead, Howard,
Lafayette, Little River, Miller,
Nevada, Pike, Sevier),
CPT CANADA POWER
TECHNOLOGY LIMITED
Mississauga
Connecticut, Delaware, District
of Columbia, Florida, Georgia,
Illinois (South of Hwy. 80),
Indiana, Iowa, Kansas, Kentucky,
Louisiana, Maine, Maryland,
Massachusetts, Michigan (except
upper Peninsula), Mississippi,
Missouri, Nebraska, New
Hampshire, New Jersey, New
York, North Carolina, Ohio,
Pennsylvania, Rhode Island,
South Carolina, Tennessee,
Vermont, Virgina, West Virginia
161 Watline Avenue
Mississauga, Ontario
L4Z−1P2
(905)890−6900ꢁ1−800−861−9559
Edmonton
101−10411−178 Street
Edmonton, Alberta
T5S 1R5
(780)453−5791ꢁ1−800−861−9559
Ville St−Laurent
234 Migneron Street
Ville St−Laurent, Quebec
H4T 1Y7
Puerto Rico
(514)731−3559ꢁ1−800−861−9559
Canada
F-040411L
Download from Www.Somanuals.com. All Manuals Search And Download.
|