Multiquip Water System MVH 304GHB User Manual

PARTS AND OPERATION MANUAL  
Reversible Plate  
Compactor  
Model MVH-304GHB  
Revision #0 (11/25/02)  
MULTIQUIPINC.  
18910 WILMINGTON AVE.  
PARTS DEPARTMENT:  
800-427-1244  
CARSON, CALIFORNIA 90746 FAX: 800-672-7877  
310-537-3700  
800-421-1244  
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:  
800-478-1244  
FAX:310-537-3927  
FAX:310-631-5032  
E-mail:[email protected] www:multiquip.com  
Atlanta • Boise • Dallas • Houston • Newark  
Montreal, Canada • Manchester, UK  
Rio De Janiero, Brazil • Guadalajara, Mexico  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HERE'S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL NUMBER  
ON-HAND WHEN CALLING  
PARTS DEPARTMENT  
800-427-1244 or 310-537-3700  
FAX: 800-672-7877 or 310-637-3284  
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE  
800-478-1244 or 310-537-3700  
FAX: 310- 537-4259  
WARRANTY DEPARTMENT  
888-661-4279, or 310-661-4279  
FAX: 310- 537-1173  
MAIN  
800-421-1244 or 310-537-3700  
FAX: 310-537-3927  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
Proposition 65 Warning ............................................. 2  
Here's How To Get Help ............................................ 3  
Table Of Contents ..................................................... 4  
Parts Ordering Procedures ....................................... 5  
HONDAGX340KSMX2ENGINE  
Air Cleaner Assembly......................................... 48-49  
Camshaft Assembly ........................................... 50-51  
Piston Assembly................................................. 52-53  
Crankcase Cover Assembly............................... 54-55  
Crankshaft Assembly ......................................... 56-57  
Cylinder Barrel Assembly................................... 58-59  
Cylinder Head Assembly.................................... 60-61  
Fan Cover Assembly .......................................... 62-63  
Flywheel Assembly ............................................ 64-65  
Fuel Tank Assembly ........................................... 66-67  
Ignition Coil Assembly ........................................ 68-69  
Carburetor Assembly ......................................... 70-71  
Muffler Assembly ............................................... 72-73  
Recoil Starter Assembly..................................... 74-75  
Control Assembly ............................................... 76-77  
Labels Assembly ................................................ 78-79  
MIKASAMVH-304GHBPLATE  
COMPACTOR  
Safety Message Alert Symbols .............................. 6-7  
Rules for Safe Operation ....................................... 8-9  
Operation and Safety Decals .................................. 10  
Specifications .......................................................... 11  
Dimensions ............................................................. 12  
Features.................................................................. 13  
Plate Compactor Components................................ 14  
Engine Components ............................................... 15  
Pre-Inspection ......................................................... 16  
Operation ........................................................... 17-20  
Maintenance ...................................................... 21-24  
Troubleshooting ................................................. 25-26  
Terms and Conditions of Sale ................................. 80  
PARTS ILLUSTRATIONS  
Explanation Of Code In Remarks Column .............. 28  
Suggested Spare Parts ........................................... 29  
Decal Placement ................................................ 30-31  
Vibrating Plate Assembly ................................... 32-33  
Base and Engine Assembly ............................... 34-37  
Vibrator Assembly .............................................. 38-41  
Hydraulic System Assembly............................... 42-43  
Control Handle Assembly .................................. 44-47  
PAGE 4 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS ORDERING PROCEDURES  
Dealer account number  
Dealer name and address  
Shipping address (if different than billing address)  
Return fax number  
Applicable model number  
Quantity, part number and description of each part  
Specify preferred method of shipment:  
UPS Ground  
UPS Second Day or Third Day*  
UPS Next Day*  
Federal Express Priority One (please provide us with your Federal  
Express account number)*  
Airborne Express*  
Truck or parcel post  
*Normally shipped the same day the order is received, if prior to 2PM west coast time.  
Earn Extra Discounts when  
you order by FAX!  
All parts orders which include complete part numbers  
and are received by fax qualify for the following extra  
discounts:  
Number of  
line items ordered  
Additional Discount  
1-9 items  
3%  
10+ items**  
5%  
only  
s
der  
d or  
e
x
a
f
For  
Get special freight allowances  
when you order 10 or more  
line items via FAX!**  
Now! Direct TOLL-FREE access  
to our Parts Department!  
UPS Ground Service at no charge for freight  
PS Third Day Service at one-half of actual freight cost  
Toll-free nationwide:  
800-421-1244  
No other allowances on freight shipped by any other carrier.  
**Common nuts, bolts and washers (all items under $1.00 list price)  
do not count towards the 10+ line items.  
Toll-free FAX:  
*DISCOUNTS ARE SUBJECT TO CHANGE*  
800/6-PARTS-7 • 800-672-7877  
Fax order discount and UPS special programs revised June 1, 1995  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — SAFETY MESSAGE ALERT SYMBOLS  
HAZARD SYMBOLS  
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!  
Safety precautions should be followed at all times when  
operating this equipment. Failure to read and understand the  
Safety Messages and Operating Instructions could result in  
injury to yourself and others.  
Lethal Exhaust Gases  
Engine exhaust gases contain poisonous  
NOTE  
carbon monoxide. This gas is colorless and  
odorless, and can cause death if inhaled.  
NEVER operate this equipment in a confined  
area or enclosed structure that does not  
provide ample free flow air.  
This Owner's Manual has been developed to provide  
complete instructions for the safe and efficient operation  
of the Multiquip Model MVH-304GHB Reversible Plate  
Compactor. Refer to the engine manufacturer’s  
instructions for data relative to its safe operation.  
Before using this reversible plate compactor, ensure  
that the operating individual has read and  
understands all instructions in this manual.  
Explosive Fuel  
GASOLINE is extremely flammable, and its  
vapors can cause an explosion if ignited. DO  
NOT start the engine near spilled fuel or  
combustible fluids. DO NOT fill the fuel tank  
while the engine is running or hot. DO NOT  
overfill tank, since spilled fuel could ignite if it  
comes into contact with hot engine parts or  
sparks from the ignition system. Store fuel in  
approved containers, in well-ventilated areas  
and away from sparks and flames. NEVER  
use fuel as a cleaning agent.  
SAFETY MESSAGE ALERT SYMBOLS  
The three (3) Safety Messages shown below will inform you  
about potential hazards that could injure you or others. The  
Safety Messages specifically address the level of exposure to  
the operator, and are preceded by one of three words: DANGER,  
WARNING, or CAUTION.  
Burn Hazards  
DANGER: You WILL be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Engine components can generate extreme heat.  
To prevent burns, DO NOT touch these areas  
while the engine is running or immediately after  
operations. Never operate the engine with heat  
shields or heat guards removed.  
WARNING: You CAN be KILLED or  
SERIOUSLY injured if you do not follow  
directions.  
Rotating Parts  
CAUTION: You CAN be injured if you  
do not follow directions.  
NEVER operate equipment with covers, or  
guards removed. Keep fingers, hands, hair and  
clothing away from all moving parts to prevent  
injury.  
Potential hazards associated with this reversible plate  
compactor operation will be referenced with Hazard Symbols  
which appear throughout this manual, and will be referenced in  
conjunction with Safety Message Alert Symbols.  
PAGE 6 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — SAFETY MESSAGE ALERT SYMBOLS  
Accidental Starting  
Respiratory Hazard  
ALWAYS place the engine ON/OFF switch in  
the OFF position, when the reversible plate  
compactor is not in use.  
ALWAYS wear approved respiratory  
protection.  
Equipment Damage Messages  
Sight and Hearing hazard  
Other important messages are provided throughout this manual  
to help prevent damage to your reversible plate compactor,  
other property, or the surrounding environment.  
ALWAYS wear approved eye and hearing  
protection.  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — RULES FOR SAFE OPERATION  
NEVER touch the hot exhaust manifold,  
muffler or cylinder. Allow these parts to  
cool before servicing engine or  
reversible plate compactor.  
CAUTION:  
Failure to follow instructions in this manual  
may lead to serious injury or even death!This  
equipment is to be operated by trained and  
qualified personnel only! This equipment is  
for industrial use only.  
The following safety guidelines should always be used when  
operating the MIKASA MVH-304GHB Reversible Plate  
Compactor:  
HighTemperatures – Allow the engine to cool before adding  
fuel or performing service and maintenance functions. Contact  
with hot components can cause serious burns.  
The engine of this reversible plate compactor requires an  
adequate free flow of cooling air. NEVER operate the  
reversible plate compactor in any enclosed or narrow area  
where free flow of the air is  
restricted. If the air flow is restricted  
it will cause serious damage to the  
reversible plate compactor or  
engine and may cause injury to  
GENERAL SAFETY  
DO NOT operate or service this equipment before  
readingthisentiremanual.  
This equipment should not be operated by  
persons under 18 years of age.  
people and property. Remember  
the vibration roller's engine gives  
off DEADLY gases.  
NEVER operate this equipment without proper  
protective clothing, shatterproof glasses, steel-  
toed boots and other protective devices required  
by the job. ALWAYS wear slip resistant safety  
shoes or boots.  
ALWAYS refuel in a well-ventilated area, away from sparks  
and open flames.  
ALWAYS use extreme caution when working with flammable  
liquids. When refueling, stop the engine and allow it to cool.  
DO NOT smoke around or near the machine. Fire or  
explosion could result from fuel vapors, or if fuel is spilled on  
a hot engine.  
NEVER operate this equipment when not feeling  
well due to fatigue, illness or taking medicine.  
NEVER operate this equipment under the  
influence or drugs or alcohol.  
NEVER operate the reversible plate compactor in an  
explosive atmosphere or near  
combustible materials. An explosion or  
fire could result causing severe bodily  
harm or even death.  
NEVER use accessories or attachments, which are not  
recommended by Multiquip for this equipment. Damage to  
the equipment and/or injury to user may result.  
Topping-off to filler port is dangerous, as  
it tends to spill fuel.  
Manufacturer does not assume responsibility for any accident  
due to equipment modifications.  
ALWAYS store the reversible plate compactor in a clean, dry  
location out of the reach of children.  
Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
NEVER run engine without air cleaner. Severe engine  
damage may occur.  
ALWAYS wear proper respiratory (mask), hearing and eye  
protection equipment when operating the reversible plate  
compactor.  
NEVER leave the reversible plate compactor unattended,  
turn off engine.  
CAUTION must always be observed while servicing this  
reversible plate compactor.Rotating parts can cause injury if  
contacted.  
DO NOT leave reversible plate compactor with engine  
running. Use chock blocks if parking reversible plate  
compactor on a grade.  
PAGE 8 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — RULES FOR SAFE OPERATION  
NEVER disconnect any "emergency or safety devices".  
These devices are intended for operator safety. Disconnection  
of these devices can cause severe injury, bodily harm or even  
death! Disconnection of any of these devices will void all  
warranties.  
ALWAYS know the location of the nearest first aid kit.  
Loading and Unloading (Crane)  
Before lifting, make sure that machine parts (hook and  
vibration insulator) are not damaged and screws are not  
loosened or lost.  
In emergencies always know the location of the  
nearest phone or keep a phone on the job site.  
Also know the phone numbers of the nearest  
ambulance, doctor and fire department. This  
information will be invaluable in the case of an  
emergency.  
Always make sure crane or lifting device has been properly  
secured to the hook of guard frame on compactor.  
NEVER lift the machine while the engine is running.  
Use adequate lifting cable (wire or rope) of sufficient strength.  
Use one point suspension hook and lift straight upwards.  
NEVER allow any person or animal to stand underneath the  
machine while lifting.  
Try not to lift machine to unnecessary heights.  
Transporting  
ALWAYS shutdown engine before transporting.  
Tighten fuel tank cap securely and close fuel cock to prevent  
fuel from spilling.  
Drain fuel when transporting compactor over long distances  
or bad roads.  
ALWAYS tie down the compactor during transportation by  
securing the compactor's guard frame with rope.  
Emergencies  
ALWAYS know the location of the nearest fire extinguisher.  
Maintenance Safety  
NEVER lubricate components or attempt service on a  
running machine.  
ALWAYS allow the machine a proper amount of time to  
cool before servicing.  
Keep the machinery in proper running condition.  
Fix damage to the machine immediately and always replace  
broken parts.  
Dispose of hazardous waste properly. Examples of  
potentially hazardous waste are used motor oil, fuel and  
fuel filters.  
DO NOT use food or plastic containers to dispose of  
hazardous waste.  
DO NOT pour waste, oil or fuel directly onto the ground,  
down a drain or into any water source.  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — OPERATION AND SAFETY DECALS  
Figure 1 displays the operation and safety decals as they appear on the reversible plate compactor. Should any of these decals  
become damaged or unreadable, contact the Multiquip Parts Department for a replacement set.  
Figure 1. Operation and Safety Decals  
PAGE 10 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB —SPECIFICATIONS  
Table 1. MVH-304DSB REVERSIBLE PLATE COMPACTOR SPECIFICATIONS  
Centrifugal Force  
39.2 kN (4000 kg)  
Vibration Frequency  
Traveling Speed  
4200 vpm (70 Hz)  
0 to 65.6 ft/min (0 to 20 m/min)  
34 x 24 in (61 x 86 cm)  
63.8 in (1620 mm)  
Plate Size (L x W)  
Overall Length  
Overall Width  
17.5 in (445 mm )  
38.2 in (970 mm )  
748 lbs. (340 kg)  
Overall Height  
Operating Weight  
Lubricating Oil in Vibration Case  
50.7 fl oz (1500 cc)  
Table 2. ENGINE SPECIFICATIONS  
Model  
HONDA GX340K1SMX2  
Air-cooled 4 stroke, Single Cylinder, OHV,  
Horizontal Shaft Gasoline Engine  
Type  
2.90 in. X 2.30 in.  
(73 mm x 58 mm.)  
Bore X Stroke  
Displacement  
23.70 cu-in (389 cm3)  
11.0 H.P./3600 R.P.M.  
1.72 gallons (6.5 liters)  
Unleaded Automobile Gasoline  
1.16 quarts (1.1 liters)  
Yes  
Max Output  
Engine  
Fuel Tank Capacity  
Fuel  
Lube Oil Capacity  
Oil Alert System  
Speed Control Method  
Starting Method  
Centrifugal Fly-weight Type  
Recoil Start  
Dimension  
(L x W x H)  
15.0 x 17.7 X 17.4 in.  
(380 X 450 X 443 mm.)  
Dry Net Weight  
68.4 lbs (31 Kg.)  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — DIMENSIONS  
Figure 2. MVH-304GHB Reversible Plate Compactor Dimensions  
TABLE 3. DIMENSIONS  
REF.  
DIMENSIONS  
53 in. (134.6 cm.)  
24 in. (61 cm.)  
A
B
C
D
E
34 in. (86 cm.)  
63.8 in. (162 cm.)  
38.2 in. (97 cm.)  
PAGE 12 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB— FEATURES  
Plate Compactor  
Frequency/Speed  
The Mikasa MVH-304GHB is a walk behind, reversible plate  
compactor designed for the compaction of sand, clay and  
asphalt. This plate compactor is a powerful compacting tool  
capable of applying a tremendous force in consecutive high  
frequency vibrations to a soil surface. Its applications include  
soil compacting for road, embankments and reservoirs as well  
as backfilling for gas pipelines, water pipelines and cable  
installation work.  
The compactor's vibrating plate maximum frequency is 4200  
vpm (vibrations per minute).The forward and reverse travel speed  
of the compactor is approximately 66 ft./minute (20 meters/  
minute).  
Engine  
The Mikasa MVH-340GHB Plate Compactor is equipped with  
an air-cooled, 4-stroke, single-cylinder HONDA GX340K1SMX2  
gasoline engine.The HONDA GX340K1SMX2 has a built-in oil  
alarm engine shut-down feature. In the event of low oil or no oil,  
the engine will automatically shut down.  
Vibratory Plates  
The vibratory plates of the MVH-304GHB produce low amplitude  
high frequency vibrations, designed to compact granular soils.  
Controls  
The resulting vibrations cause forward motion.The engine and  
handle are vibration isolated from the vibrating plate.The heavier  
the plate, the more compaction force it generates.  
Before starting the MVH-340GHB Plate Compactor, identify and  
understand the function of the controls and components as  
indicated in Figure 3.  
ReversibleVibratory Plates  
Reversible vibratory plates have two eccentric weights that allow  
a smooth transition for forward and reverse travel, plus increased  
compaction force as the result of dual weights.  
Due to their weight and force, reversible plates are ideal for  
semi-cohesive soils.  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB— PLATE COMPACTOR COMPONENTS  
Figure 3. MVH-304GHB Reversible Plate Compactor Components  
Figure 3 illustrates the location of the major components 7.  
for the MVH-304GHB Reversible Plate Compactor. The  
function of each component is described below:  
Belt Cover – Remove this cover to gain access to the  
V-belts.NEVER run the compactor without theV-belt cover.  
If the V-belt cover is not installed, the possibility exist that  
your hand may get caught between the V-belt and clutch,  
thus causing serious injury and bodily harm.  
1.  
Hand Grip – When operating the compactor use this hand  
grip to maneuver the compactor.  
8. Base Plate – Designed to compact sand, clay, and asphalt.  
2.  
Forward & Reverse Lever – Push the lever forward, the  
compactor will move in a forward direction, pull the lever 9. OilTank Fill with proper grade of engine oil.  
backwards, the compactor will move in backwards direction.  
Placing the lever in the middle (midway) will cause the  
compactor not to move (neutral).  
10. Vibration Case – Encloses the eccentric, gears and  
counter weights.  
11. Hydraulic Cylinder – Activated by moving the travel lever.  
3.  
Handle Bar When operating the compactor, this handle  
is to be in the downward position.When the compactor is  
to be stored, move the handle bar to the upright position.  
The cylinder controls the direction of movement by the plate  
compactor.  
12. Shock Absorber – Protects plate compactor from damage  
4.  
5.  
6.  
Guard Hook - Used to lift the machine with crane or other  
lifting device.  
by absorbing vibration during operation.  
13. Throttle Lever – Controls the speed of the plate compactor.  
Stopper - Locks the handle in place in the upward position  
for stowing.  
Place straight vertically to start, push fully counterclockwise  
for full trottle and fully clockwise to stop plate compactor.  
Engine – This plate compactor uses a HONDA  
GX340K1SMX2 engine. Refer to the owner’s manual for  
engine information and related topics.  
PAGE 14 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB— ENGINE COMPONENTS  
Figure 4. Engine Controls and Components  
INITIAL SERVICING  
6. Choke Lever – Used in the starting of a cold engine, or in  
cold weather conditions. The choke enriches the fuel  
mixture.  
The engine (Figure 4) must be checked for proper lubrication and  
filled with fuel prior to operation. Refer to the manufacturers engine  
manual for instructions & details of operation and servicing. The  
engine shown above is a HONDA engine, operation for other  
types of engines may vary somewhat.  
7. Air Cleaner – Prevents dirt and other debris from entering  
the fuel system. Remove wing-nut on top of air filter  
cannister to gain access to filter element.  
1. Fuel Filler Cap – Remove this cap to add unleaded  
gasoline to the fuel tank. Make sure cap is tightened  
securely. DO NOT over fill.  
Operating the engine without an  
air filter, with a damaged air filter,  
or a filter in need of replacement  
will allow dirt to enter the engine,  
causing rapid engine wear.  
DANGER  
Adding fuel to the tank should be done only when  
the engine is stopped and has had an opportunity to  
cool down. In the event of a fuel spill, DO NOT attempt to start the  
engine until the fuel residue has been completely wiped up, and the  
area surrounding the engine is dry.  
8. Spark Plug – Provides spark to the ignition system. Set  
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean  
spark plug once a week.  
9. Muffler Used to reduce noise and emissions.  
2. Throttle Lever – Used to adjust engine RPM speed (lever  
advanced forward SLOW, lever back toward operator  
FAST).  
WARNING  
3. Engine ON/OFF Switch – ON position permits engine  
Engine components can generate extreme heat.  
To prevent burns, DO NOT touch these areas  
starting, OFF position stops engine operations.  
4. Recoil Starter (pull rope) – Manual-starting method. Pull  
the starter grip until resistance is felt, then pull briskly and  
smoothly.  
while the engine is running or immediately after operating. NEVER  
operate the engine with the muffler removed.  
10. Fuel Tank – Holds unleaded gasoline. For additional  
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop  
information refer to engine owner's manual.  
the flow of fuel.  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — PRE-INSPECTION  
CAUTION  
Table 4. Oil Type  
NEVER operate the  
compactor in a confined  
area or enclosed area  
structure that does not  
provide ample free flow of  
air.  
Season  
Summer  
Spring/Fall  
Winter  
Temperature  
25°C or Higher  
25°C~10°C  
Oil Type  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
0°C or Lower  
ALWAYS wear approved eye and hearing  
protection before operating the compactor.  
Before Starting  
1.  
Read safety instructions at the beginning  
of manual.  
Figure 6. Engine Oil Dipstick (Oil Level)  
Explosive Fuel  
2.  
Familiarize yourself with the operating  
and control elements of the machine and  
the working environment. This includes  
obstacles in the working area, bearing  
capacity of the ground and the necessary safety provisions.  
DANGER  
Motor fuels are highly flammable and can be  
dangerous if mishandled. DO NOT smoke while  
refueling. DO NOT attempt to refuel the compactor  
if the engine is hot! or running.  
3.  
4.  
5.  
Check the air filter for dirt and dust. If air filter is dirty, replace  
air filter with a new one as required.  
Check carburetor for external dirt and dust. Clean with dry  
compressed air.  
Checking The Fuel  
1. Remove the fuel cap located on top of fuel tank.  
2. Visually inspect to see if fuel level is low. If fuel is low,  
replenish with unleaded gasoline (Figure 7).  
3. When refueling, be sure to use a strainer for filtration.  
Check fastening nuts and bolts for tightness.  
6. Understand the geographical features and regulations ofthe  
job site.  
7.  
Clean the compactor, removing dirt and dust.Particularly,  
the bottom of the plate, engine cooling air inlet.  
DO NOT top-off fuel. Wipe up any spilled fuel.  
Engine Oil Check  
1.  
To check the engine oil level, place the compactor on secure  
level ground with the engine stopped.  
2.  
Remove the filler dipstick from the engine oil filler hole  
(Figure 5) and wipe clean  
Figure 7. Refueling  
DANGER  
Fuel spillage on a hot engine can cause a  
fire or explosion. If fuel spillage occurs,  
wipe up the spilled fuel completely to  
prevent fire hazards. NEVER! smoke  
around or near the compactor.  
Figure 5. Engine Oil Dipstick (Removal)  
3. Insertandremovethedipstickwithoutscrewingitintothefiller  
neck. Check the oil level shown on the dipstick.  
4. If the oil level is low (Figure 6), fill to the edge of the oil filler  
hole with the recommended oil type (Table 4).Maximum oil  
capacity is 1.16 quarts (1.1 liters).  
PAGE 16 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB— OPERATION  
CAUTION :  
DO NOT attempt to operate thecompactor until the Safety,  
General Information and Inspection sections of this manual have  
been read and thoroughly understood.  
Figure 10. Throttle Lever (Start Position)  
This section is intended to assist the operator with the initial  
start-up of the compactor. It is extremely important that this  
section be read carefully before attempting to use the compactor  
in the field.  
3. Place the choke lever (Figure 11) in the "OPEN " position  
if starting a cold engine.  
Refer to Figures 3 and 4 for the location of controls and  
components.  
Adjusting Handle Height  
The heigh of the handle is adjustable for your comfort .  
1. Loosen the butterfly screw (Figure 8).  
2. Turn the grip clockwise to raise the handle or counterclock-  
wise to lower the handle.  
3. When the handle is raised to the desired height, tighten the  
butterflyscrew.  
Figure 11. Engine Choke Lever (Open)  
4. Placethechoke lever(Figure12)in the"CLOSED"position  
if starting a warm engine or the temperature is warm.  
Figure 8. Handle Height Adjustment  
Starting the Engine (HONDA engine)  
1. Place the engine fuel valve lever (Figure 9) to the "ON"  
position.  
Figure 12. Engine Choke Lever (Closed)  
Figure 9. Engine FuelValve Lever (ON Position)  
2.  
Move the throttle lever to the STARTposition by opening it  
to about 20 degrees (Figure 10).  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — OPERATION  
5. Place the engine ON/OFF switch (Figure 13) in the "ON "  
TRAVELING  
position.  
CAUTION :  
Makesuretofollowallsafetyrulesreferencedin  
thesafetysectionofthismanualbeforeoperating  
compactor. Keep work area clear of debris and  
other objects that could cause damage to the  
compactororbodilyinjury.  
1. Graspthecompactor'shandgrip(Figure16), andmovethe  
throttle lever (Figure 16) quickly to the fast position.  
2. With the throttle lever in the fast position, the engine speed  
should be around 2,300 RPM, therefore engaging the cen-  
trifugalclutch  
Figure 13. Engine ON/OFF Switch (ON Position)  
6. Grasp the starter grip (Figure 14) and slowly pull it out.The  
resistancebecomesthehardestatacertainposition,corre-  
spondingtothecompressionpoint.Pullthestartergripbriskly  
andsmoothlyforstarting.  
Figure 16. Throttle Lever ((Fast)  
Figure 14. Starter Grip  
7. If the engine has started, slowly return the choke lever  
(Figure 15 ) to the CLOSED position. If the engine has not  
started repeat steps 1 through 6.  
ALWAYS move the throttle lever  
quickly without hesitation, because  
increasing the engine speed slowly  
causes the clutch to slip.  
3. To make the compactor move in the forward direction push  
the travel lever ( Figure 17) forward  
Figure 15. Choke Lever (Closed)  
8. Beforethecompactoris placedintooperation,runtheengine  
for several minutes. Check for fuel leaks, and noises that  
would be associated with a loose component.  
Figure 17. Travel Lever  
PAGE 18 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB—OPERATION  
4. Place the fuel shut-off lever (Figure 20) in the OFF  
4. Tomakethecompactormoveinthereversedirectionpullthe  
travel lever ( Figure 17) backwards.  
position.  
5. Firmly gasp the compactor's hand grip, the compactor will  
beginmovinginthedesiredpositionwhenthedirectionlever  
has been placed in the desired position.  
6. Slowlywalkbehindthecompactorandbeonthelookout for  
anylargeobjectsorforeignmatterthatmightcausedamage  
to the compactor or bodily injury.  
7. Iftravelleverisplacedintheneutralposition,themachinewill  
vibrate in place.  
Figure 20. Fuel Valve Lever (OFF)  
Emergency Shutdown  
8. Tomovethecompactorlaterally,holdthehandgripfirmlyand  
swingcompactor. Donotswingcompactorwhilegrippingthe  
travel lever.  
1. Move the throttle lever quickly to the STOP position, and  
place the engine ON/OFF switch in the OFF position.  
STOPPING  
1.  
Return the throttle lever to the START position. Allow  
the machine to cool down for 2 to 3 minutes.  
STOWING THE HANDLE  
2. Turn the throttle lever to the STOP position (Figure 18) to  
1.  
Push up the handle (Figure 21).  
stop the engine.  
2. Pull the stopper grip upward into the hole of the guard  
frame to lock the handle.  
Figure 18. Throttle Lever (Stop)  
3. Turn the engine ON/OFF switch to the “OFFposition (Figure 19).  
Figure  
Figure 19. Engine ON/OFF Switch (OFF)  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — OPERATION  
LIFTING  
1.  
2.  
3.  
4.  
5.  
Use a crane or lift to load and unload the machine. A  
skilled crane operator is required to perform the job.  
When lifting the machine, check for any damaged or  
loose bolts, lifting hooks, and shock mounts.  
Check any damaged or loose bolts in the guard frame to  
avoid machine sliding off.  
Make sure that the machine is shut off before machine is  
lifted.  
Use reliable cable for lifting.  
6. Always lift the machine vertically and keep the  
machine away from workers and animals.  
7.  
Do not lift the machine higher than the required  
height.  
TRANSPORTING  
1. Always make sure that the machine is shut off while  
being transported.  
2. Check that the fuel cap is properly closed and  
tightened.  
3. When traveling long distances or on rugged terrain,  
drain the fuel of the machine before transporting.  
4. Tie down the machine securely on the  
transportation so that it will not move or topple over.  
PAGE 20 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — MAINTENANCE  
CAUTION:  
TABLE 6. MVH-304GHB ENGINE CHECK  
Inspection and other services should always be  
carried out on hard and level ground with the  
engine shutdown.  
ITEM  
HOURS OF OPERATION  
Spark Plug Check  
Oil or Fuel Leak  
Every 40 hours (every week)  
Every 8 hours (every day)  
Inspection and Maintenance ServiceTables.  
1. To make sure your plate compactor is always in good  
working condition before using, carry out the maintenance  
inspection in accordance withTables 5 through 7.  
Tightness of Fastening  
Threads  
Every 8 hours (every day)  
Every 8 hours (every day)  
(Replenish to specified maximum  
level)  
Engine Oil Check and  
Replenishment  
TABLE 5. MVH-304GHB MACHINE INSPECTION  
After first 25 hours then every 50 to  
100 hours  
Engine Oil Replacement  
Air Filter Cleaning  
HOURS OF  
ITEM  
REMARKS  
Every 100 hours  
OPERATION  
Loose or Missing  
Screws  
Every 8 hours  
(every day)  
See separate engine manual for details on engine check.  
Every 8 hours  
(every day)  
Daily Service  
Damaged Parts  
z
z
Check for leakage of fuel or oil.  
Function of Controlling Every 8 hours  
System Part (every day)  
Check for loose screws including tightness. See Table 7  
below (tightening torque ), for retightening:  
Hydraulic System Leak Every 100 hours  
TABLE 7. TIGHTENING TORQUE  
(in. kg/cm) Diameter  
Vibrator Oil Check  
Every 100 hours See page 23  
Every 300 hours See page 23  
Every 100 hours See page 23  
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm  
Vibrator Oil  
Replacement  
4T  
70  
150  
250  
400  
300  
500  
800  
500  
750  
1,100  
2,000  
2,900  
1,400  
2,000  
6-8T  
11T  
100  
150  
800  
1,300  
2,000  
2,700 3,800  
4,200 5,600  
Hydraulic Oil Check  
1,200  
First after 200  
hours, then every See page 24  
1,000 hours  
Hydraulic Oil  
Replacement  
300~ 650 ~  
350 700  
*
100  
* (In case counter-part is of aluminum)  
(Threads in use with this machine are all right handed)  
Material and quality of material is marked on each bolt, and screw.  
V-belt (clutch) Check Every 200 hours See page 23  
z
Remove soil and clean the bottom of compaction plate.  
CAUTION:  
z
Check hydraulic pump, piping and hose for any leakage. A  
loosened hydraulic hose can be a cause for leakage. Check  
hydraulic hose connections with wrench applied for  
tightness.  
These inspection intervals are for operation under  
normal conditions. Adjust your inspection intervals  
based on the number hours plate compactor is  
in use, and particular working conditions. Fuel  
piping and connections should be replaced every  
2 years.  
z
Check engine oil.  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — MAINTENANCE  
Spark Plug  
Air Filter  
1. Remove and clean the spark plug (Figure 22).  
1. Remove the air cleaner cover and foam filter element as  
shown in Figure 24.  
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This  
unit has electronic ignition, which requires no adjustments.  
2. Tap the paper filter element (Figure 24) several times on a  
hard surface to remove dirt, or blow compressed air [not  
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter  
elementfromtheaircleanercaseside.NEVER brushoffdirt.  
Brushingwillforcedirtintothefibers.Replacethepaperfilter  
element if it is excessively dirty.  
3. Cleanfoamelementinwarm,soapywaterornonflammable  
solvent. Rinseanddrythoroughly. Diptheelementinclean  
engineoilandcompletelysqueezeouttheexcessoilfromthe  
element before installing.  
Figure 22. Spark Plug Gap  
Engine Oil Replacement  
1. Replace engine oil, first in 25 hours of operation and every  
50 to 100 hours afterwards.  
2. Drain the engine oil when the oil is warm as shown in  
Figure 23.  
3. Remove the oil drain bolt and sealing washer and allow  
the oil to drain into a suitable container.  
4. Replace engine oil with recommended type oil as listed  
in Table 4. Engine oil capacity is 1.16 quarts (1.1 liters).  
DO NOT overfill.  
5. Install drain bolt with sealing washer and tighten se-  
curely.  
Figure 24. Engine Air Filter  
CAUTION:  
NEVER attempt to check theV-belt with the en-  
ginerunning.Severeinjurycan occurifyourhand  
gets caught between the V-belt and the clutch  
(Figure25). Alwaysusesafetygloves.  
CLUTCH  
PULLEY  
Figure 23. Engine Oil (Draining)  
VIBRATOR  
PULLEY  
Figure 25. V-Belt Hazard  
PAGE 22 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB—MAINTENANCE  
Checking and Replacing the V-Belt and Clutch  
Vibrator Oil Level Check  
1. After 200 hours of operation, remove the belt cover to check  
the V-belt tension (Figure 26).Tension is proper if the belt  
bends about 10 mm when depressed strongly with finger  
between shafts. Loose or worn V-belts reduces power  
transmission efficiency, causing weak compaction and  
reduces the life of the belt itself.  
CAUTION:  
Alwayscleantheareaaroundthevibratoroillevel  
check hole before removing oil check plug.This  
will prevent dirt and debris from entering the  
system.  
1. In every 100 hours of operation, with the machine positioned  
horizontally, remove vibrator oil level check plug (Figure 27)  
off vibrator (19 mm wrench) and see if oil is up to filler port.  
Be sure to clean area around check hole to prevent dirt and  
dust from entering.  
2. In every 300 hours of operation, replace oil (capacity 1,500  
cc). For draining oil through level check hole, have the  
machine inclined with a sleeper or the like placed under the  
compaction plate on opposite side.  
* Use engine oil 10W-30 for this lubrication.  
Figure 26. V-Belt Check  
z
Replacing the V-belt  
Remove the belt cover. Engage an offset wrench (19 mm) or the  
like to vibrator pulley (lower) fastening bolt. Engage waste cloth  
or the like at midway ofV-belt on the left side and while pulling it  
back strongly, rotate the offset wrench clockwise so that the V-  
belt will come off.  
z
Reinstalling the V-belt  
EngageV-belt to lower vibrator pulley and push theV-belt to left  
side of upper clutch and, in the same manner as in removal,  
rotate offset wrench clockwise so that theV-belt goes back on.  
z
Checking Clutch  
Figure 27 . Vibrator Oil Maintenance  
Hydraulic Oil  
Check the clutch simultaneously withV-belt checking. With belt  
cover removed, check outer drum of the clutch for seizure and  
"V" groove for wear or damage with your eyes. Clean the "V"  
groove as necessary. Wear of lining or shoe should be checked  
with running check. If the shoe is worn, power transmission  
becomes deficient and slipping will result.  
1. Check hydraulic oil in every 100 hours of operation. With  
handle bar positioned vertically (storage position), remove  
bleeder plug (Figure 28) off the top of hydraulic pump and  
check for proper oil level.  
2. Replace hydraulic oil after first 200 hours and in every 1,000  
hours of operation.  
z
Replacing Clutch  
RemoveV-belt.Remove bolt at engine power output by giving a  
shock to an engaged wrench (tapping with hammer or the like)  
and rotating bolt counterclockwise. Remove clutch with a pulley  
extractor.To reinstall, reverse the procedure.  
CAUTION:  
Whenever the compactor's vibration becomes  
weak or lost during normal operation regardless  
of operation hours, check the V-belt and clutch  
immediately.  
Figure 28. Bleeder Plug  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB—MAINTENANCE  
CAUTION :  
CAUTION:  
Make sure hydraulic oil i is at a normal safe  
Wear safety glasses or face mask,  
protective clothes, and rubber gloves when  
working with battery.  
operating level. DO NOT over fill. Over filling  
(excessive oil) will cause excess oil to blow out  
of breather plug.  
Replacing Hydraulic Oil  
1. Remove the drain plug (Figure 29) at the bottom of the oil  
tank with a 6 mm hex wrench and drain the hydraulic oil.  
2. Clean the filter with light oil.  
3. Reinstall the drain plug to the oil tank. Apply seal tape or  
Roctite #575 to thread portion.  
Troubleshooting  
4. Fill tank with hydraulic oil. (Capacity: About 2,500 cc). Use  
See Tables 8 (engine) and 9 (plate compactor) on proceeding  
pages for engine and plate compactor troubleshooting guide.  
ShellTellus Oil #46 or equivalent.  
5. After filling tank, temporarily install cover. Loosen bleeder  
plug located at the top of the cylinders on side of vibrator  
(Figure 28). Air remaining in the circuit will be forced out of  
the bleeder plug.  
6. Tighten the breather plug.Check oil level in the tank again.  
7. Install the cover of oil tank. Coat packing with liquid packing  
such as Threebond #1215. Use loctite #242 for mounting  
screw.  
Figure 29. Hydraulic Oil Maintenance  
PAGE 24 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB—TROUBLESHOOTING (ENGINE)  
diagnosis based on the Engine Troubleshooting (Table 8)  
information shown below and on the proceeding page. If the  
problem cannot be remedied, please leave the unit just as it  
is and consult our company's business office or service plant.  
Practically all breakdowns can be prevented by proper  
handling and maintenance inspections, but in the event of a  
breakdown, please take a remedial action following the  
TABLE 8. ENGINE TROUBLESHOOTING  
SYMPTOM  
POSSIBLE CAUSE  
SOLUTION  
Check gap, insulation or  
replace spark plug.  
Spark plug bridging?  
Carbon deposit on spark plug?  
Clean or replace spark plug.  
Difficult to start, "fuel is available, but no  
SPARK at spark plug".  
Short circuit due to deficient spark plug  
insulation?  
Check spark plug insulation,  
replace if worn.  
Improper spark plug gap?  
ON/OFF switch is shorted?  
Ignition coil defective?  
Set to proper gap.  
Check switch wiring, replace  
switch.  
Replace ignition coil.  
Set correct spark gap and  
clean points.  
Difficult to start, "fuel is available, and  
SPARK is present at the spark plug".  
Improper spark gap, points dirtry?  
Condenser insulation worn or short  
circuiting?  
Replace condenser.  
Replace defective spark plug  
wiring.  
Spark plug wire broken or short circuiting?  
Wrong fuel type?  
Flush fuel system, and replace  
with correct type of fuel.  
Difficult to start, "fuel is available, spark  
is present and compression is normal"  
Water or dust in fuel system?  
Air cleaner dirty?  
Flush fuel system.  
Clean or replace air cleaner.  
Re-seat valves.  
Suction/exhaust valve stuck or protruded?  
Replace piston rings and or  
piston.  
Piston ring and/or cylinder worn?  
Difficult to start, "fuel is available, spark  
is present and compression is low"  
Cylinder head and/or spark plug not  
tightened properly?  
Torque cylinder head bolts and  
spark plug.  
Head gasket and/or spark plug gasket  
damaged?  
Replace head and spark plug  
gaskets.  
Fuel not available in fuel tank?  
Fill with correct type of fuel.  
Apply lubricant to loosen fuel  
cock lever, replace if necessary.  
Fuel cock does not open properly?  
No fuel present at carburetor.  
Fuel filter clogged?  
Replace fuel filter.  
Fuel tank cap breather hole clogged?  
Air in fuel line?  
Clean or replace fuel tank cap.  
Bleed fuel line.  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB—TROUBLESHOOTING (ENGINE)  
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)  
SYMPTOM  
POSSIBLE CAUSE  
Air cleaner not clean?  
SOLUTION  
Clean or replace air cleaner  
Check float adjustment, re-build  
carbureator.  
Improper level in carburetor?  
"Weak in power" compression is  
proper and does not misfire.  
Defective Spark plug?  
Defective Spark plug?  
Clean or replace spark plug.  
Flush fuel system, and replace  
with correct type of fuel.  
Water in fuel system?  
"Weak in power" compression is  
proper but misfires.  
Dirty spark plug?  
Clean or replace spark plug.  
Replace ignition coil.  
Ignition coil defective?  
Replace with correct type of  
spark plug.  
Spark plug heat value improper?  
Engine overheats.  
Correct type of fuel?  
Replace with correct type of fuel  
Clean cooling fins.  
Cooling fins dirty?  
Governor adjusted correctly?  
Governor spring defective?  
Adjust governor.  
Replace governor spring.  
Rotational speed fluctuates.  
Recoil starter malfunction.  
Check entire fuel system for  
leaks or clogs.  
Fuel flow restricted?  
Recoil mechanism clogged with dust and Clean recoil assembly with soap  
dirt?  
and water.  
Sprial spring loose?  
Replace sprial spring.  
PAGE 26 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB—TROUBLESHOOTING (PLATE COMPACTOR)  
diagnosis based on the CompactorTroubleshooting (Table 9)  
information shown below and on the proceeding page. If the  
problem cannot be remedied, please leave the unit just as it  
is and consult our company's business office or service plant.  
Practically all breakdowns can be prevented by proper  
handling and maintenance inspections, but in the event of a  
breakdown, please take a remedial action following the  
TABLE 9. TROUBLESHOOTING COMPACTOR  
SYMPTOM  
POSSIBLE CAUSE  
SOLUTION  
Adjust or replace clutch.  
Clutch slips?  
V-belt slips?  
Adjust or replace V-belt.  
Fill to correct level..  
Excessive Oil in vibrator?  
Check vibrator assembly for any worn or  
defective parts, replace any defective  
parts.  
Travel speed low and vibration weak.  
Trouble in vibrator internals?  
Aeration in hydraulic oil for for travel  
reversing syste.?  
Purge air in hydraulic oil. (Bleed plug)  
Engine speed incorrect?  
Set engine speed to correct RPM.  
Check entire travel system.  
Clean installation of reversing lever.  
Replace oil hose.  
Travel reversing system inoperative.?  
Reversing lever installation correct?  
Broken or defective oil hose?  
Aeration in hydraulic oil for for travel  
reversing syste.?  
Travels forward or backward but unable  
to switch direction.  
Purge air in hydraulic oil. (Bleed plug)  
Excessive oil in reversing system?  
Selector valve clogged with trash?  
Fill to correct level..  
Clean selector valve.  
Check piston bearing in cylinder for  
leakage at USH packing.  
Cylinder piston bearing failure?  
V-belt dis-engaged or slips?  
Clutch slips?  
Engage V-belt, adjust or replace.  
Adjust clutch, replace if necessary.  
Does not travel in forward or reverse.  
Pump input shat key or adapter key-way  
damaged?  
Replace input shatkey or adapter key-way  
Check piston bearing in cylinder for  
leakage at USH packing.  
Cylinder piston bearing failure?  
Excessive hydraulic oil?  
Reversing lever operating resistance  
great.  
Fill to correct level.  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLANATION OF CODE IN REMARKS COLUMN  
How to read the marks and remarks used in this parts  
book.  
Items Found In the “Remarks” Column  
Serial Numbers-Where indicated, this indicates a serial  
number range (inclusive) where a particular part is used.  
Model Number-Where indicated, this shows that the  
corresponding part is utilized only with this specific model  
number or model number variant.  
Items Found In the “Items NumberColumn  
MAll parts with the same symbol in the number column,  
*,#,+,%, or , belong to the same assembly or kit  
PAGE 28 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED SPARE PARTS  
MVH-304GHB1TO 5 UNITSWITH HONDA  
GX340K1SMX2 ENGINE  
Qty.  
P/N  
Description  
5 ............ 17210ZE3505 ....... ELEMENT AIR CLEANER  
5 ............ 17218ZE3505 ....... FILTER OUTER  
5 ............ 9807956846 .......... SPARK PLUG (HONDA)  
1 ............ 17620ZH7023 ....... CAP, FUEL TANK (HONDA)  
2 ............ 17672ZE2W01 ...... FUEL, FILTER  
1 ............ 070200353 ............ V-BELT  
1 ............ 456449280 ............ FILTER, OIL TANK  
1 ............ 956100030 ............ THROTTLE WIRE  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — DECAL PLACEMENT  
DECAL PLACEMENT  
PAGE 30 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — DECAL PLACEMENT  
DECAL PLACEMENT  
NO.  
1
2
3
4
5
6
PART NO.  
TBD  
NPA455  
NPA222  
TBD  
NPA638  
NPA748  
PART NAME  
QTY.  
REMARKS  
IGNITION SYSTEM DECAL  
FULLTHROTTLE DECAL  
FORWARD/REVERSE DECAL  
MULTIQUIP LOGO DECAL  
OPERATIONAL CAUTION DECAL  
SHELL OIL #46DECAL  
1
1
1
1
1
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB VIBRATING PLATE ASSY.  
VIBRATING PLATE ASSY.  
PAGE 32 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB VIBRATING PLATE ASSY.  
VIBRATING PLATE ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
456113260  
953405840  
953402930  
953405270  
953405260  
939010070  
020316130  
030216400  
001221645  
001201830  
030218460  
030216400  
456336550  
456210690  
001221850  
PART NAME  
QTY.  
REMARKS  
VIBRATING PLATE 445B  
DRAIN PLUG M18 (H)  
COPPER PACKING 19X30X1  
PLUG 1/4X14 13L  
PACKING 1/4 (CU)  
SHOCK ABSORBER 100  
NUT M16  
1
1
1
1
1
4
4
4
4
8
8
4
1
WASHER16  
BOLT 16X45 T  
BOLT 18X30  
WASHER M18  
9
10  
11  
12  
13  
15  
16  
WASHER M16  
COVER GUARD  
EXTENSION PLATE .................................. 2......... OPTION  
BOLT 18X50 T ............................................ 8......... OPTION  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — BASE AND ENGINE ASSY.  
BASE AND ENGINE ASSY.  
PAGE 34 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — BASE AND ENGINE ASSY.  
BASE AND ENGINE ASSY.  
NO.  
1
2
3
7
8
9
PART NO.  
456115320  
912234002  
456450200  
456113830  
001220825  
030208200  
031108160  
456445120  
456445721  
456335600  
951400110  
455444350  
030208200  
001220825  
070200353  
456113790  
001221052  
030210250  
031110160  
456114850  
001221230  
030212300  
456335520  
456437920  
001221235  
PART NAME  
QTY.  
1
1
1
1
4
4
4
1
1
1
1
1
1
1
1
1
4
4
4
1
4
4
1
1
REMARKS  
BASE (GX340 /390)  
ENGINE AY GX340  
ENGINE BASE (GX340) E2474-  
BELT COVER (IN) GX340  
BOLT 8X25 T  
WASHER M8  
WASHER M8  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
22  
23  
24  
25  
26  
27  
28  
29  
COVER SEAL 125D  
SPACER 25-32-21  
CLUTCH AY W/FAN  
KEY 7X7X35  
WASHER, CLUTCH  
WASHER M8  
BOLT 8X25 T  
V-BELT B-35 GREEN  
BELT COVER (OUT)  
BOLT 10X60 T  
WASHER M10  
WASHER M10  
GUARD FRAME  
BOLT 12X30 T  
WASHER M12  
PULLEY B1-105 W/FAN /MVH  
WASHER, PULLEY  
BOLT 12X35 T  
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — BASE AND ENGINE ASSY.  
BASE AND ENGINE ASSY.  
PAGE 36 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — BASE AND ENGINE ASSY.  
BASE AND ENGINE ASSY.  
NO.  
30  
31  
32  
33  
34  
41  
42  
43  
45  
46  
47  
48  
49  
55  
56  
57  
58  
59  
60  
61  
62  
63  
64  
PART NO.  
030212300  
301010950  
456334920  
001221015  
030210250  
031110160  
456334630  
001520816  
456334860  
001221020  
030210250  
001221030  
020310080  
030210250  
031110160  
001221045  
456450820  
456450800  
001220825  
031108160  
022710809  
954405510  
031105080  
PART NAME  
QTY.  
1
1
1
2
2
1
1
2
1
1
2
1
1
4
4
4
1
1
2
2
2
1
1
REMARKS  
WASHER M12  
RETURN SPRING  
COVER, OIL TANK  
BOLT 10X15 T  
WASHER M10  
WASHER M10  
PUMP COVER  
SOCKET HEAD BOLT 8X16 T  
GUARD PIPE  
BOLT 10X20 T  
WASHER M10  
BOLT 10X30 T  
NUT M10  
WASHER M10  
WASHER M10  
BOLT 10X45 T  
RUBBER COVER, GX  
PLATE, COVER  
BOLT 8X25 T  
WASHER M8  
NYLON NUT M8  
CLAMP CLA-3200 (9D)  
WASHER M5  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB VIBRATOR ASSY.  
VIBRATOR ASSY.  
PAGE 38 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB VIBRATOR ASSY.  
VIBRATOR ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
456110250  
001221470  
001221450  
030214350  
047920060  
457212410  
457445830  
951405370  
456327150  
080200550  
060105030  
951404970  
456327170  
009120301  
456337670  
009120302  
456337380  
456010010  
456327120  
040306911  
455435020  
456451280  
080100300  
042506000  
PART NAME  
VIBRATING CASE  
BOLT 14X150T  
BOLT 14X50 T  
WASHER M14  
ROLLER BEARING NJ310MC4  
ROTARY SHAFT, DRIVE  
ADAPTER, PUMP  
KEY 15X10X39 RR  
GEAR, DRIVE  
STOP RING S-55  
OIL SEAL SB-50729  
KEY 12X8X30 R  
ECCENTRIC ROTOR  
SOCKET HEAD BOLT 16X40T  
ROTARY, SHAFT DRIVEN  
SOCKET HEAD BOLT 16X30T  
PISTON ROD  
KNOCK PIN 10X70  
GEAR, DRIVEN  
BEARING 6911C3  
COLLAR 17X30X3  
SPRING 3.2-26.3-102L /304B  
STOP RING R-30  
QTY.  
1
6
4
10  
4
1
1
1
1
2
1
1
4
2
1
2
1
REMARKS  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
23  
24  
25  
1
1
2
2
1
1
2
BEARING 6000ZZSG  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB VIBRATOR ASSY.  
VIBRATOR ASSY.  
PAGE 40 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB VIBRATOR ASSY. (CONTINUED)  
VIBRATOR ASSY.  
NO.  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
41-1  
42  
43  
44  
45  
46  
47  
48  
49  
PART NO.  
080200100  
455435051  
455010070  
080100260  
455327130  
456210646  
954405550  
050101050  
001221025  
030210250  
001220812  
953404600  
455010020  
031110160  
457332430  
457010010  
457010090  
457445840  
952405470  
001221035  
001221030  
952405540  
030210250  
954010140  
954001780  
PART NAME  
STOP RING S-10  
PISTON, 22.4D  
PACKING USH-22.4X30X5  
STOP RING R-26  
BEARING COVER  
CYLINDER (R)  
CLAMP 15R  
O-RING G-105  
BOLT 10X25 T  
WASHER M10  
QTY.  
1
1
1
1
1
1
1
3
9
12  
1
1
1
10  
1
1
1
1
REMARKS  
BOLT 8X12 T  
COPPER PACKING 8X16X2  
ELBOW 45 15-0404  
WASHER M10  
FLANGE, PUMP  
PUMP FBL  
CRESCENT KEY 2.5X10 GEAR PUMP  
BRACKET, CLAMP  
SHIM 90X110X0.5  
BOLT 10X35 T  
BOLT 10X30 T  
WASHER 10.5-22-3  
WASHER M10  
ELBOW 90 UES90G02G02  
ELBOW 45 PF3/8-PF1/4  
2
2
3
2
2
1
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — HYDRAULIC SYSTEM ASSY.  
HYDRAULIC SYSTEM ASSY.  
PAGE 42 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — HYDRAULIC SYSTEM ASSY.  
HYDRAULIC SYSTEM ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
001220820  
030208200  
031108160  
456451310  
456451340  
456451320  
456451330  
955404271  
954403060  
954403070  
001220612  
030206150  
506010070  
954001160  
456114080  
456335830  
001220620  
030206150  
031106100  
954001280  
001221230  
030212300  
031112230  
505015380  
456337460  
457445870  
001200820  
030208200  
031108160  
456449280  
456447490  
954001720  
506010060  
953402781  
457448680  
953400020  
457448380  
456337780  
PART NAME  
QTY.  
4
4
4
1
1
1
1
3
1
1
2
2
1
4
1
1
6
6
6
1
4
4
4
1
1
1
2
2
2
1
1
1
2
1
REMARKS  
BOLT 8X20 T  
WASHER M8  
WASHER M8  
OIL HOSE 1300L  
OIL HOSE 1100L  
OIL HOSE 730L  
OIL HOSE 1050L  
SPIRAL TUBE, SR15-850L  
CLAMP HC-40  
CLAMP SPACER HC-40  
BOLT 6X12 T  
WASHER M6  
CLAMPTC-150  
ELBOW 90 PT1/4-PF1/4  
OIL TANK  
COVER (SLIDE), OIL TANK  
BOLT 6X20 T  
WASHER M6  
WASHER M6  
ELBOW 45 PT1/4XPF3/8  
BOLT 12X30 T  
WASHER M12  
WASHER M12  
PLUG PT1/4  
UPPER COVER, OIL TANK  
PACKING, OIL TANK  
BOLT 8X20  
WASHER M8  
WASHER M8  
9
10  
11  
12  
13  
14  
16  
18  
20  
21  
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
51  
FILTER, OIL TANK  
JOINT PIPE  
ELBOW PT1/4  
CLAMPTC-350  
DRAIN PLUG M18  
BREATHER PLUG 1  
PACKING 19302  
BREATHER CAP  
SELECTOR VALVE  
2
1
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — CONTROL HANDLE ASSY.  
CONTROL HANDLE ASSY.  
PAGE 44 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — CONTROL HANDLE ASSY.  
CONTROL HANDLE ASSY.  
NO.  
1
2
3
4
5
7
8
9
PART NO.  
456336410  
456336420  
001221235  
030212300  
031112230  
456336400  
456449940  
456449930  
001221681  
032124400  
025406016  
031116260  
020316130  
020416100  
001220640  
020306050  
455434950  
455010030  
939010060  
020410060  
020412070  
022411635  
954404230  
001220620  
030206150  
031106100  
020306050  
001220825  
030208200  
031108160  
953401580  
501402870  
501402880  
959403460  
020410060  
456449980  
954305260  
031110160  
456450760  
456214360  
PART NAME  
QTY.  
1
1
4
4
4
2
2
2
1
2
2
2
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
6
6
6
1
1
1
1
1
1
1
1
1
1
REMARKS  
HANDLE BRACKET (L)  
HANDLE BRACKET (R)  
BOLT 12X35 T  
WASHER M12  
WASHER M12  
RUBBER COUPLING  
SHOCK ABSORBER  
RUBBER PLATE  
BOLT 16X250 T  
CONICAL SPRING WASHER M24  
SPRING PIN 6X16  
WASHER M16  
NUT M16  
NUT M16, H=10  
BOLT 6X40 T  
NUT M6  
SPINDLE  
KNOB  
SHOCK ABSORBER 60  
NUT M10, H=6  
NUT M12, H=7  
WING NUT M16  
CLAMP SA120-18  
BOLT 6X20 T  
WASHER M6  
WASHER M6  
NUT M6  
BOLT 8X25 T  
WASHER M8  
WASHER M8  
PLUG  
HANDLE STOPPER  
SPRING/HANDLE (1.4X18X44)  
BALL GRIP 32D-M10  
NUT M10, H=6  
RUBBER PACKING 9D-200-5T  
PACKING 1/4 (CU)  
WASHER M10  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
43  
JOINT  
LEVER BRACKET  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — CONTROL HANDLE ASSY.  
CONTROL HANDLE ASSY.  
PAGE 46 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-304GHB — CONTROL HANDLE ASSY. (CONTINUED)  
CONTROL HANDLE ASSY.  
NO.  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
61  
62  
62  
63  
64  
65  
66  
67  
68  
69  
71  
72  
73  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
PART NO.  
456214720  
001220820  
030208200  
031108160  
001220815  
033910020  
457445910  
001220850  
020308060  
031108160  
001220630  
020306050  
031106100  
456114840  
456214220  
456214222  
456214210  
032112220  
456451400  
456337400  
608010090  
457332480  
020412070  
959403840  
456337690  
456451290  
456452070  
951401431  
031112230  
020412070  
032112220  
953402930  
509010130  
959021624  
956100030  
001820830  
020308060  
PART NAME  
LEVER BRACKET  
BOLT 8X20 T  
WASHER M8  
PWASHERM8  
BOLT 8X15 T  
THRUSTWASHER 20-36-1.5T  
CLEVIS  
BOLT 8X50 T  
NUT M8  
WASHER M8  
BOLT 6X30 T  
NUT M6  
WASHER M6  
HANDLE (FOR JPN)  
HANDLE GRIP  
HANDLE GRIP  
VALVE BRACKET  
CONICAL SPRING WASHER M12  
WASHER 12.2-27- 0.6T  
TRAVEL LEVER  
BUSHING MB2015DU  
GRIP, TRAVEL LEVER  
NUT M12, H=7  
BAR GRIP I.D. 12MM  
THROTTLE LEVER  
WIRE GUIDE.............................................. 1........ UP TO S/N 3897  
WIRE GUIDE.............................................. 1........ S/N G3898 AND ABOVE  
KEY 5X5X8  
WASHER M12  
NUT M12, H=7  
CONICAL SPRING WASHER M12  
COPPER PACKING 19X30X1  
BUSHING MB1825DU  
TUBE 8-13-150L  
QTY.  
1
1
3
3
2
2
1
1
2
2
1
2
2
1
1
1
1
2
2
1
2
1
3
1
REMARKS  
1
1
2
2
2
2
1
1
THROTTLEWIRE 1860-2080 ..................... 1......... FOR GX390  
BOLT 8X30 T WHOLE THREAD ................. 1......... S/N G3898 AND ABOVE  
NUT M8 ...................................................... 1......... S/N G3898 AND ABOVE  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
PAGE 48 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — AIR CLEANER ASSY.  
AIR CLEANER ASSY.  
NO.  
1
2
3
4
5
6
7
*
8
*
9
11  
12  
13  
14  
PART NO.  
PART NAME  
QTY.  
REMARKS  
16271ZE2000  
17210ZE3505  
17218ZE3505  
17231ZE3W00  
17232891000  
17235ZH9N00  
17238ZE2310  
17239ZE1000  
17410ZH9N00  
90203ZA0800  
90325044000  
934040602008  
9405006000  
GASKET, ELBOW  
1
1
1
1
1
1
2
1
ELEMENT, AIR CLEANER  
FILTER, OUTER  
COVER, AIR CLEANER  
GROMMET, AIR CLEANER  
NOSE, MUFFLER  
COLLAR, AIR CLEANER  
COLLAR B, AIR CLEANER  
ELBOW, AIR CLEANER ............................... 1 ........... INCLUDES ITEMS W/  
*
WINGNUT, 6MM  
1
1
1
2
WINGNUT, TOOL BOX SETTING  
BOLT- WASHER, 6X20  
NUT, FLANGE (6MM)  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CAMSHAFT ASSY.  
CAMSHAFT ASSY.  
PAGE 50 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CAMSHAFT ASSY.  
CAMSHAFT ASSY.  
NO.  
1
2
3
4
PART NO.  
PART NAME  
QTY.  
REMARKS  
14100ZE3305  
14410ZE3013  
14431ZE2010  
14441ZE2000  
14451ZE1013  
14568ZE1000  
14711ZE3000  
14721ZE3000  
14751ZE2003  
14771ZE2000  
14773ZE2000  
14775ZE2010  
14781ZE2000  
14791ZE2010  
90012ZE0010  
90206ZE1000  
12209ZE8003  
CAMSHAFT ASSEMBLY ......................1........... INCLUDES ITEMS W/  
*
ROD, PUSH  
ARM, VALVE ROCKER  
LIFTER, VALVE  
PIVOT, ROCKER ARM  
SPRING, WEIGHT RETURN  
VALVE, IN.  
2
2
2
2
1
1
1
2
1
1
1
1
1
2
2
5
6
*
7
8
VALVE, EX.  
SPRING, VALVE  
9
10  
11  
12  
13  
14  
15  
16  
17  
RETAINER, IN. VALVE SPRING  
RETAINER, EX. VALVE SPRING  
SEAT, VALVE SPRING  
ROTATOR, VALVE  
PLATE, PUSH ROD GUIDE  
BOLT, PIVOT (8MM)  
NUT, PIVOT ADJ.  
SEAL, VALVE STEM.............................1........... USE FROM ENGINE S/N 3334264  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — PISTON ASSY.  
PISTON ASSY.  
PAGE 52 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — PISTON ASSY.  
PISTON ASSY.  
NO.  
1
1
1
1
2
2
2
2
3
4
4
5
*
6
PART NO.  
PART NAME  
QTY.  
REMARKS  
13010ZE3003  
13011ZE3003  
13012ZE3003  
13013ZE3003  
13101ZE3W00  
13102ZE3W00  
13103ZE3W00  
13104ZE3W00  
13111ZF6000  
13200ZE3010  
13200ZE3315  
90001ZE8000  
90601ZE3000  
RING SET, PISTON- STANDARD  
RING SET, PISTON- OS 0.25  
RING SET, PISTON- OS 0.50  
RING SET, PPISTON- 0.75  
PISTON- STANDARD  
PISTON- OS 0.25  
1
1
1
1
1
1
1
1
1
PISTON- OS 0.50  
PISTON- 0.75  
PIN, PISTON  
ROD ASSEMBLY, CONNECTING (STD.) ..................... 1 ....... INCLUDES ITEMS W/  
ROD ASSEMBLY, CONNECTING- US 0.25 ................. 1 ....... INCLUDES ITEMS W/  
BOLT, CONNECTING ROD  
CLIP, PISTON PIN 20MM  
*
*
2
2
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CRANKCASE COVER ASSY.  
CRANKCASE COVER ASSY.  
PAGE 54 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CRANKCASE COVER ASSY.  
CRANKCASE COVER ASSY.  
NO.  
1+  
2
3
4
PART NO.  
PART NAME  
QTY.  
REMARKS  
06165ZE3000  
11300ZE3602  
11381ZE3801  
15600ZG4003  
15600735003  
15625ZE1003  
15625ZE1003  
16510ZE3000  
16511ZE8000  
16512ZE3000  
16513ZE2000  
16531ZE2000  
90602ZE1000  
90701HC4000  
91201ZE3004  
9410106800  
GOVERNOR KIT, ............................................... 1 ........... INCLUDES ITEMS W/  
*
COVER ASSEMBLY, CRANKCASE Q- TYPE ... 1 ........... INCLUDES ITEMS W/+  
GASKET, CASE COVER  
CAP ASSEMBLY, OIL FILLER ........................... 1 ........... INCLUDES ITEMS W/$  
CAP ASSEMBLY, OIL FILLER ........................... 1 ........... INCLUDES ITEMS W/  
GASKET, OIL FILLER CAP  
GASKET, OIL FILLER CAP  
GOVERNOR ASSEMBLY .................................. 1 ........... INCLUDES ITEMS W/%  
1
5
7$  
1
1
8
9+  
10 +  
%
%
%
WEIGHT, GOVERNOR  
3
1
3
1
1
2
1
1
7
1
1
*
11 +  
*
HOLDER, GOVERNORWEIGHT  
PIN, GOVERNOR WEIGHT  
SLIDER, GOVERNOR  
CLIP, GOVERNOR HOLDER  
PIN, DOWEL 8X12  
OIL SEAL 35X52X8  
WASHER, PLAIN 6MM  
BOLT, FLANGE 8X40  
12 +  
*
13 +  
*
15 +  
*
16  
17+  
18 +  
*
19  
20+  
957010804000  
961006202000  
961006207000  
BEARING, RADIAL BALL 6202  
BEARING, RADIAL BALL 6207  
21+  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CRANKSHAFT ASSY.  
CRANKSHAFT ASSY.  
PAGE 56 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CRANKSHAFT ASSY.  
CRANKSHAFT ASSY.  
NO.  
1
5
6
7
PART NO.  
PART NAME  
QTY.  
REMARKS  
13310ZE3601  
13351ZE3010  
90756ZE2600  
961006207000  
CRANKSHAFT Q- TYPE ............................. 1 .....................INCLUDES ITEMS W/  
*
WEIGHT, BALANCER  
KEY 6.3X6.3X43  
BEARING, RADIAL BALL 6207  
1
1
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CYLINDER BARREL ASSY.  
CYLINDER BARREL ASSY.  
PAGE 58 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CYLINDER BARREL ASSY.  
CYLINDER BARREL ASSY.  
NO.  
1
2
PART NO.  
12000ZE3816  
15510ZE2043  
PART NAME  
QTY.  
REMARKS  
CYLINDER ASSEMBLY ............................... 1 ........... INCLUDES ITEMS W/  
SWITCH ASSEMBLY, OIL LEVEL ............... 1 ........... USE FROM ENGINE  
*
SN 2639738TO 2786139  
3
4
5
6
7
16541ZE3010  
32197ZE2003  
90013883000  
90131896650  
90446KE1000  
91201ZE3004  
91201ZE9003  
91353671003  
9405010000  
9410912000  
9425110000  
957010601200  
961006202000  
90013883000  
34150ZH7003  
SHAFT, GOVERNOR ARM  
SUB- HARNESS .......................................... 1 ........... USE UP TO ENGINE SN 2639737  
BOLT,FLANGE 6X12 (CT200)....................... 1 ........... USE UP TO ENGINE SN 2639737  
BOLT, DRAIN PLUG  
WASHER 8.2X17X0.8  
OIL SEAL 35X52X8  
1
2
1
1
1
1
1
2
1
2
1
1
1
9
*
10  
OIL SEAL 8X14X5  
O- RING 13.5X1.5  
*
11  
12  
13  
14  
15  
16  
17  
NUT, FLANGE 10MM  
WASHER, DRAIN PLUG 12MM  
PIN, LOCK 10MM  
BOLT, FLANGE 6X12  
BEARING, RADIAL BALL 6202  
BOLT, FLANGE 6X12 (CT200)  
ALERT UNIT, OIL  
*
18  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CYLINDER HEAD ASSY.  
CYLINDER HEAD ASSY.  
PAGE 60 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CYLINDER HEAD ASSY.  
CYLINDER HEAD ASSY.  
NO.  
PART NO.  
PART NAME  
QTY.  
REMARKS  
1
12200ZF6W01  
12204ZE2306  
12205ZE2305  
12216ZE2300  
12251ZE3W00  
12310ZE3791  
12315ZE3840  
12391ZE2020  
90014ZE2000  
90042ZE8000  
90047ZE2000  
92900080320E  
90441ZE2010  
9430112200  
CYLINDER HEAD......................................... 1 ........... INCLUDES ITEMS W/  
*
2
*
3
*
4
*
5
6
7
GUIDE, EX. VALVE OS (OPTIONAL)  
GUIDE, EX. VALVE OS (OPTIONAL)  
CLIP, VALVE GUIDE  
GASKET, CYLINDER HEAD  
COVER, HEAD  
TUBE, BREATHER  
GASKET, CYLINDER HEAD COVER  
BOLT, HEAD COVER  
1
1
1
1
1
1
1
1
2
8
10  
11  
12  
12  
13  
14  
15  
16  
BOLT, STUD 8X131.5  
BOLT, STUD 8X47 ........................................ 2 ........... USE UP TO ENGINE SN 3033461  
BOLT 2, STUD 8X32 .................................... 2 ........... USE FROM ENGINE SN 3033462  
WASHER, HEAD COVER  
PIN A, DOWEL 12X20  
BOLT, FLANGE 10X80  
SPARK PLUG, BPR6ES (NGK)  
1
2
4
1
957011008000  
9807956846  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — FAN COVER ASSY.  
FAN COVER ASSY.  
PAGE 62 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — FAN COVER ASSY.  
FAN COVER ASSY.  
NO.  
1
2
3
4
5
5
7
8
PART NO.  
PART NAME  
QTY.  
REMARKS  
16731ZE2003  
19610ZE3010ZA  
19631ZE3W00  
32197ZH8003  
36100ZE1015  
36100ZH7003  
90013883000  
90684ZA0601  
CLIP, TUBE  
1
1
1
COVER, FAN *R8* (BRIGHT RED)  
SHROUD  
SUB- HARNESS .......................................... 1 ........... USE UP TO ENGINE SN 2639737  
SWITCH ASSEMBLY, ENGINE STOP ......... 1 ........... USE UP TO ENGINE SN 2639737  
SWITCH ASSEMBLY, ENGINE STOP ......... 1 ........... USE FROM ENGINE SN 2639738  
BOLT, FLANGE 6X12 (CT200)  
CLIP, WIRE HARNESS  
6
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — FLYWHEEL ASSY.  
FLYWHEEL ASSY.  
PAGE 64 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — FLYWHEEL ASSY.  
FLYWHEEL ASSY.  
NO.  
1
2
4
6
6
7
PART NO.  
PART NAME  
QTY.  
REMARKS  
19511ZE3000  
28450ZE3W11  
31100ZE3701  
90201ZE3V00  
90201ZE3790  
90741ZE2000  
FAN, COOLING  
1
1
1
PULLEY, STARTER (SCREEN GRID)  
FLYWHEEL  
NUT, SPECIAL 16MM (1) ............................. 1 ........... USE FROM ENGINE SN 2536523  
NUT, SPECIAL 16MM .................................. 1 ........... USE UP TO ENGINE SN 2536522  
KEY, SPECIAL WOODRUFF 25X18  
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 65  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — FUELTANK ASSY.  
FUEL TANK ASSY.  
PAGE 66 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — FUELTANK ASSY.  
FUEL TANK ASSY.  
NO.  
1
2
3
3
5
6
*
7
10  
11  
12  
13  
14  
PART NO.  
PART NAME  
RUBBER, SUPPORTER 107MM  
JOINT, FUEL TANK  
TANK, FUEL *NH31* (MCKINLEY WHITE)  
TANK FUEL *T34* (SIMPSON BLUE)  
CAP, FUEL FILLER ............................................1 ............INCLUDES ITEMS W/  
GASKET, FUEL FILLER CAP  
FILTER, FUEL  
O- RING 13.5X1.5 (ARA)  
NUT, FLANGE 8MM  
BULK HOSE, FUEL (4.5X3000) (4.5X235)  
CLIP, TUBE B8  
BOLT, FLANGE 8X25  
QTY.  
REMARKS  
16854ZH8000  
16955ZE1000  
17510ZE3010ZA  
17510ZE3010ZD  
17620ZH7023  
17631ZH7003  
17672ZE2W01  
91353671003  
9405008000  
1
1
1
1
*
1
1
1
2
1
2
2
950014500360M  
9500202080  
957010802500  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 67  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — IGNITION COIL ASSY.  
IGNITION COIL ASSY.  
PAGE 68 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — IGNITION COIL ASSY.  
IGNITION COIL ASSY.  
NO.  
1
2
4
7
PART NO.  
PART NAME  
QTY.  
REMARKS  
30500ZE2023  
30700ZE1013  
31512ZE2000  
36101ZE2701  
90015883000  
COIL ASSEMBLY, IGNITION  
CAP ASSEMBLY, NOISE SUPPRESSOR  
GROMMET, WIRE  
1
1
1
1
2
WIRE, STOP SWITCH 430MM  
BOLT, FLANGE 6X28  
10  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 69  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CARBURETOR ASSY.  
CARBURETOR ASSY.  
PAGE 70 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CARBURETOR ASSY.  
CARBURETOR ASSY.  
NO.  
PART NO.  
PART NAME  
QTY.  
REMARKS  
1
2
3
%
16010ZE2812  
16011ZA0931  
16013ZA0931  
16015ZE2005  
GASKET SET  
VALVE SET, FLOAT  
FLOAT SET  
1
1
1
*
*
*
4
CHAMBER SET, FLOAT ............................... 1 ........... INCLUDES ITEMS W/  
.................................................................................... USE UP TO ENGINE SN BE80B A  
CHAMBER SET, FLOAT ............................... 1 ........... INCLUDES ITEMS W/  
.................................................................................... USE FROM ENGINE SN BE80B B  
%
*
4
16015ZE8005  
%
*
5
16016ZH7W01  
16024ZE1811  
16028ZE0005  
16044ZE3811  
16100ZE3V00  
SCREW SET  
1
1
1
1
*
6
7
%
SCREW SET, DRAIN  
SCREW SET B  
CHOKE SET  
*
*
8
9
*
CARBURETOR ASSEMBLY, BE85B A ........ 1 ........... INCLUDES ITEMS W/  
*
.................................................................................... USE UP TO ENGINE SN 2519695  
CARBURETOR ASSEMBLY, BE80B B ........ 1 ........... USEFROM ENGINE SN 2519696  
CARBURETOR ASSEMBLY, BE80B B ........ 1 ........... USE UP TO ENGINE SN 2519695  
SCREW, THROTTLE STOP  
NOZZLE, MAIN  
9
9
16100ZE3V01  
16100ZE3V01  
16124ZE0005  
16166ZE3W50  
16172ZE3W10  
16173001004  
16211ZE3000  
16220ZA0702  
16221ZE3800  
16223ZE3800  
16610ZE1000  
16953ZE1812  
16954ZE1812  
16956ZE1811  
16957ZE1812  
16967ZE0811  
93500030060H  
9430520122  
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
1
1
1
1
1
1
1
1
1
*
*
*
COLLAR, SET  
GASKET, FUEL STRAINER CUP  
INSULATOR, CARBURETOR  
SPACER, CARBURETOR  
GASKET, CARBURETOR  
GASKET, INSULATOR  
LEVER, CHOKE (STANDARD)  
LEVER, VALVE ............................................ 1 ........... USE FROM ENGINE SN BE80B B  
PLATE, LEVER SETTING ............................ 1 ........... USE FROM ENGINE SN BE80B B  
SPRING, VALVE LEVER  
GASKET, VALVE  
CUP, FUEL STRAINER  
SCREW, PAN (3X6) ......................................2............ USE FROM ENGINE SN BE80B B  
PIN, SPRING (2X12)  
INCLUDES ITEMS W/+  
1
1
1
*
*
*
*
25+  
26  
1
1
1
1
1
99101ZH80880  
99101ZH80900  
99101ZH80920  
99204ZE00350  
JET, MAIN #88 (OPTIONAL)  
JET, MAIN #90 (OPTIONAL)  
JET, MAIN #92 (OPTIONAL)  
JET SET, PILOT #35  
26  
26  
27  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 71  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — MUFFLER ASSY.  
MUFFLER ASSY.  
PAGE 72 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — MUFFLER ASSY.  
MUFFLER ASSY.  
NO.  
1
2
3
4
5
6
6
8
PART NO.  
PART NAME  
QTY.  
1
REMARKS  
18310ZE3W00  
18320ZE3W01  
18323ZE3W40  
18330ZE2W00  
18331ZE3810  
18333ZF6W01  
18333ZK6Y00  
18355ZE3010  
18381ZE2W10  
90013883000  
90050ZE1000  
90055ZE1000  
93500060060B  
9405008000  
MUFFLER  
PROTECTOR, MUFFLER  
PROTECTOR, EX. PIPE  
PIPE, EX.  
1
1
1
1
1
1
1
1
1
6
3
1
CAP, MUFFLER  
GASKET, EX. PIPE  
GASKET, EX. PIPE (WACKER)  
ARRESTER, SPARK  
GASKET, MUFFLER (ARRESTER)  
BOLT, FLANGE 6X12 (CT200)  
SCREW, TAPPING 5X8  
SCREW, TAPPING 4X6  
SCREW, PAN 6X6  
9
11  
12  
13  
14  
15  
NUT, FLANGE 8MM  
5
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 73  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — RECOIL STARTER ASSY.  
RECOIL STARTER ASSY.  
PAGE 74 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — RECOIL STARTER ASSY.  
RECOIL STARTER ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
PART NAME  
QTY. REMARKS  
28400ZEW01ZA  
28410ZE3W01ZA  
28421ZE3W01  
28422ZE2W01  
28441ZE2W01  
28442ZE2W01  
28443ZE2W01  
28444ZE2W01  
28445ZE2W01  
28461ZE2W02  
28462ZE3W01  
28469ZE2W01  
90004ZE2W01  
957010600800  
STARTER ASSY., RECOIL *R8* BGHT RED ........... 1 ...... INCLUDES ITEMS W/  
*
CASE, RECOIL STARTER *R8* BGHT RED  
PULLEY, RECOIL STARTER  
RATCHET, STARTER  
SPRING, FRICTION  
SPRING, STARTER RETURN  
SPRING, RATCHET  
RETAINER, SPRING  
HOLDER, SPRING  
GRIP, STARTER  
ROPE, RECOIL STARTER  
1
1
2
1
1
2
1
1
1
1
9
10  
11  
12  
13  
14  
GRIP, REINFORCEMENT ........................................ 1 ...... USE UP TO ENG. SN 2935312  
SCREW, CENTER  
BOLT, FLANGE 6X8  
1
3
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 75  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CONTROL ASSY.  
CONTROL ASSY.  
PAGE 76 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — CONTROL ASSY.  
CONTROL ASSY.  
NO.  
2
3
4
5
7
8
9
10  
11  
12  
14  
15  
17  
18  
19  
22  
23  
24  
PART NO.  
PART NAME  
QTY.  
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
REMARKS  
16551ZE3000  
16555ZE3000  
16561ZE3000  
16562ZE3000  
16570ZE3W20  
16571ZE3W00  
16574ZE1000  
16575ZE2W00  
16576891000  
16589ZE1000  
16584883300  
16592883310  
90013883000  
90015ZE5010  
90114SA0000  
93500050320A  
93500050160A  
9405006000  
ARM, GOVERNOR  
ROD, GOVERNOR  
SPRING, GOVERNOR  
SPRING, THROTTLE RETURN  
CONTROL ASSEMBLY, REMOTE  
LEVER, CONTROL  
SPRING, LEVER  
WASHER, CONTROL LEVER  
HOLDER, CABLE  
SPACER, CONTROL LEVER  
SPRING, CONTROL ADJUSTING  
SPRING, CABLE RETURN  
BOLT, FLANGE 6X12 (CT200)  
BOLT, GOVERNOR ARM  
NUT, SELF- LOCK 6MM  
SCREW, PAN 5X32  
SCREW, PAN 5X16  
NUT, FLANGE 6MM  
1
1
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 77  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — LABELS ASSY.  
LABELS ASSY.  
PAGE 78 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HONDA GX340K1SMX2 — LABELS ASSY.  
LABELS ASSY.  
NO.  
1
3
4
6
PART NO.  
PART NAME  
QTY.  
REMARKS  
87521ZE3W01  
87522ZH9000  
87528ZE2810  
87532ZH8810  
89218ZE1000  
EMBLEM  
1
1
1
1
1
LABEL, CAUTION  
MARK, CHOKE (EXTERNAL)  
MARK, OIL ALERT (E)  
WRENCH, SPARK PLUG  
9
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 79  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Effective: October 1, 2002  
TERMS AND CONDITIONS OF SALE — PARTS  
5. Parts must be in new and resalable  
condition,intheoriginalMultiquippack-  
age (if any), and with Multiquip part  
numbersclearlymarked.  
Rebatesforpricedeclinesandaddedcharges  
for price increases will not be made for stock  
onhandatthetimeofanypricechange.  
PAYMENT TERMS  
Terms of payment for parts are net 10 days.  
FREIGHTPOLICY  
Multiquip reserves the right to quote and sell  
directtoGovernmentagencies,andtoOriginal  
Equipment Manufacturer accounts who use  
our products as integral parts of their own  
products.  
All parts orders will be shipped collect or  
prepaidwiththechargesaddedtotheinvoice.  
All shipments are F.O.B. point of origin.  
Multiquip’sresponsibilityceaseswhenasigned  
manifest has been obtained from the carrier,  
andanyclaimforshortageordamagemustbe  
settledbetweentheconsigneeandthecarrier.  
6. Thefollowingitemsarenotreturnable:  
a. Obsolete parts.(If an item is in the  
price book and shows as being  
replaced by another item, it is  
obsolete.)  
SPECIALEXPEDITINGSERVICE  
b. Any parts with a limited shelf life  
(such as gaskets, seals, “O” rings,  
and other rubber parts) that were  
purchased more than six months  
priortothereturndate.  
A$35.00surchargewillbeaddedtotheinvoice  
forspecialhandlingincludingbusshipments,  
insuredparcelpostorincaseswhereMultiquip  
mustpersonallydeliverthepartstothecarrier.  
MINIMUMORDER  
TheminimumchargeforordersfromMultiquip  
is $15.00 net. Customers will be asked for  
instructionsregardinghandlingofordersnot  
meetingthisrequirement.  
LIMITATIONSOFSELLER’SLIABILITY  
c. Anylineitemwithanextendeddealer  
netpriceoflessthan$5.00.  
Multiquip shall not be liable here under for  
damagesinexcessofthepurchasepriceofthe  
itemwithrespecttowhichdamagesareclaimed,  
andinnoeventshallMultiquipbeliableforloss  
of profit or good will or for any other special,  
consequentialorincidentaldamages.  
RETURNEDGOODSPOLICY  
d. Special order items.  
Returnshipmentswillbeacceptedandcredit  
willbeallowed,subjecttothefollowingprovi-  
sions:  
e. Electricalcomponents.  
f. Paint,chemicals,andlubricants.  
g. Decalsandpaperproducts.  
h. Itemspurchasedinkits.  
1. AReturnedMaterialAuthorizationmust  
be approved by Multiquip prior to ship-  
ment.  
LIMITATIONOFWARRANTIES  
Nowarranties,expressorimplied,aremadein  
connectionwiththesaleofpartsortradeacces-  
soriesnorastoanyenginenotmanufactured  
byMultiquip.Suchwarrantiesmadeinconnec-  
tion with the sale of new, complete units are  
madeexclusivelybyastatementofwarranty  
packagedwithsuchunits,andMultiquipnei-  
ther assumes not authorizes any person to  
assume for it any other obligation or liability  
whatever in connection with the sale of its  
products.Apartfromsuchwrittenstatementof  
warranty, there are no warranties, express,  
impliedorstatutory,whichextendbeyondthe  
descriptionoftheproductsonthefacehereof.  
7. The sender will be notified of any  
materialreceivedthatisnotacceptable.  
2. ToobtainaReturnMaterialAuthorization,  
alistmustbeprovidedtoMultiquipParts  
Salesthatdefinesitemnumbers,quanti-  
ties, and descriptions of the items to be  
returned.  
8. Such material will be held for five  
workingdaysfromnotification,pending  
instructions. If a reply is not received  
within five days, the material will be  
returnedtothesenderathisexpense.  
a. Thepartsnumbersanddescriptions  
must match the current parts price  
list.  
9. Creditonreturnedpartswillbeissuedat  
dealer net price at time of the original  
purchase,lessa15%restockingcharge.  
b. The list must be typed or computer  
generated.  
10. Incaseswhereanitemisaccepted,for  
which the original purchase document  
cannotbedetermined,thepricewillbe  
basedonthelistpricethatwaseffective  
twelvemonthspriortotheRMAdate.  
c. The list must state the reason(s) for  
thereturn.  
d. The list must reference the sales  
order(s)orinvoice(s)underwhichthe  
itemswereoriginallypurchased.  
11. Credit issued will be applied to future  
purchasesonly.  
e. The list must include the name and  
phonenumberofthepersonrequest-  
ingtheRMA.  
PRICINGANDREBATES  
Prices are subject to change without prior  
notice.Pricechangesareeffectiveonaspe-  
cific date and all orders received on or after  
that date will be billed at the revised price.  
3. AcopyoftheReturnMaterialAuthoriza-  
tionmustaccompanythereturnshipment.  
4. Freight is at the sender’s expense. All  
partsmustbereturnedfreightprepaidto  
Multiquip’sdesignatedreceivingpoint.  
PAGE 80 — MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MQ-MIKASA MVH-304GHB PLATE COMPACTOR — PARTS & OPERATION MANUAL — REV. #0 (11/25/02) — PAGE 81  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS AND OPERATION MANUAL  
HERE'S HOW TO GET HELP  
PLEASE HAVE THE MODEL AND SERIAL NUMBER  
ON-HANDWHEN CALLING  
PARTS DEPARTMENT  
800-427-1244 or 310-537-3700  
FAX: 800-672-7877 or 310-637-3284  
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE  
800-478-1244 or 310-537-3700  
FAX: 310- 537-4259  
WARRANTY DEPARTMENT  
888-661-4279, or 310-661-4279  
FAX: 310- 537-1173  
MAIN  
800-421-1244 or 310-537-3700  
FAX: 310-537-3927  
MULTIQUIP INC.  
POST OFFICE BOX 6254  
CARSON, CA 90749  
310-537-3700 • 800-421-1244  
FAX:310-537-3927  
WWW:multiquip.com  
Atlanta • Boise • Dallas • Houston • Newark  
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX  
manufactured for Multiquip Inc.  
by  
MIKASA SANGYO CO., LTD. Tokyo, Japan  
Download from Www.Somanuals.com. All Manuals Search And Download.  

NEC Personal Computer VT 300i User Manual
Neuro Logic Systems Mouse 17 User Manual
NexxTech Calculator 6500542 User Manual
Nikon Camera Lens 1933 User Manual
Nokia Cell Phone 103 User Manual
Olympus Microcassette Recorder VN 1100 VN 1100PC User Manual
Orion Car Audio Car Speaker XTR52 User Manual
Oster Coffee Grinder 6389 33 User Manual
Panasonic Air Conditioner CS E18CKE User Manual
Panasonic Network Card Digital Signage User Manual