Multiquip Trash Compactor MVH 200DA User Manual
OPERATION & PARTS MANUAL  
SERIES  
MODEL MVH-200DA  
REVERSIBLE PLATE COMPACTOR  
(YANMAR DIESEL ENGINE)  
Revision #0 (03/21/05)  
THIS MANUAL MUST ACCOMPANY  
THE EQUIPMENT AT ALLTIMES.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
HERE'S HOW TO GET HELP  
PLEASE HAVETHE MODEL AND SERIAL  
NUMBER ON-HANDWHEN CALLING  
MULTIQUIP CORPORATE OFFICE  
18910 Wilmington Ave.  
Carson, CA 90746  
800-421-1244  
FAX:310-537-3927  
Email: [email protected]  
Internet:www.multiquip.com  
PARTS DEPARTMENT  
800-427-1244  
310-537-3700  
FAX:800-672-7877  
FAX:310-637-3284  
MAYCO PARTS  
800-306-2926  
310-537-3700  
FAX:800-672-7877  
FAX:310-637-3284  
SERVICE DEPARTMENT  
800-421-1244  
FAX:310-537-4259  
310-537-3700  
TECHNICAL ASSISTANCE  
800-478-1244  
FAX:310-631-5032  
FAX:310-537-1173  
WARRANTYDEPARTMENT  
800-421-1244, EXT.279  
310-537-3700, EXT.279  
© COPYRIGHT 2004, MULTIQUIP INC.  
Multiquip Inc and the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without  
written permission. All other trademarks are the property of thier respective owners and used with permission.  
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and  
should remain with the unit if resold.  
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are  
based on the Mikasa MVH-200DA Plate Compactor. Illustrations, descriptions, references and technical data contained in this  
manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change  
specifications, design or the information published in this publication at any time without notice and without incurring any obligations.  
To find the latest revision of this  
publication, visit our website at:  
www.multiquip.com  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 3  
Download from Www.Somanuals.com. All Manuals Search And Download.  
TABLE OF CONTENTS  
YANMAR L70EE-DVMK  
MIKASA SERIES MVH-200DA  
PLATE COMPACTOR  
ENGINE  
Cylinder Block Assembly.................................... 44-45  
Cylinder Head Assembly.................................... 46-47  
Air Cleaner & Muffler Assembly ......................... 48-49  
Crankshaft, Piston and Camshaft Assembly ..... 50-51  
Lub. Oil Pump and Governor Assembly ............. 52-53  
Cooling and Starting Device Assembly.............. 54-55  
Fuel Injection Pump Assembly........................... 56-57  
Fuel Tank and Fuel Line Assembly .................... 58-59  
Tool, Label and Gasket Set Assembly ............... 60-61  
Proposition 65 Warning ............................................. 2  
Here’s How To Get Help ............................................ 3  
Table Of Contents ..................................................... 4  
Parts Ordering Procedures ....................................... 5  
Specifications ............................................................ 6  
Dimensions ............................................................... 7  
Safety Message Alert Symbols .............................. 8-9  
Rules for Safe Operation.................................... 10-11  
Operation and Safety Decals .................................. 12  
Features .................................................................. 13  
Plate Compactor Components................................ 14  
Engine Components ............................................... 15  
Pre-Inspection ......................................................... 16  
Start-up Procedure ................................................. 17  
Operation ........................................................... 18-19  
Maintenance ...................................................... 20-24  
Troubleshooting ................................................. 25-26  
Explanation Of Code In Remarks Column .............. 28  
Suggested Spare Parts ........................................... 29  
Terms and Conditions Of Sale — Parts .................. 62  
COMPONENT DRAWINGS  
Decal Placement ................................................ 30-31  
Body Assembly .................................................. 32-33  
Vibration Assembly ............................................ 34-37  
Control (A-type) Assembly ................................. 38-39  
Pump (A-type) Assembly ................................... 40-41  
Throttle (A-type) Assembly ................................ 42-43  
Specification and part  
number are subject to  
change without notice.  
PAGE 4 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
PARTS ORDERING PROCEDURES  
When ordering parts,  
please supply the following information:  
❒
Dealeraccountnumber  
❒
❒
❒
❒
❒
❒
Dealernameandaddress  
Shipping address (if different than billing address)  
Returnfaxnumber  
Applicable model number  
Quantity,part number and description of each part  
Specifypreferredmethodofshipment:  
Note:Unlessotherwiseindicatedbycustomer, all  
orders are treated as “Standard Orders”, and will  
ship within 24 hours.We will make every effort to  
ship “Air Shipments” the same day that the order is  
received, if prior to 2PM west coast time. “Stock  
Orders” must be so noted on fax or web forms.  
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground  
FedEx or UPS Second Day or Third Day  
FedEx or UPS Next Day  
Federal Express Priority One  
DHL  
Truck  
Place Your Parts Order Via Web or Fax  
For Even More Savings!  
Here’s how to get help...  
Please have the model and serial number  
on hand when calling.  
MULTIQUIP CORPORATE OFFICE  
Extra Discounts!  
18910 Wilmington Ave.  
Carson, CA 90746  
800-421-1244  
FAX: 310-537-3927  
All parts orders which include complete part numbers  
and are received by our automated web parts order  
system, or by fax qualify for the following extra  
discounts:  
Email: [email protected]  
Internet: www.multiquip.com  
PARTS DEPARTMENT  
800-427-1244  
310-537-3700  
Ordered  
via  
Standard  
orders  
Stock orders  
($750 list and above)  
FAX: 800-672-7877  
FAX: 310-637-3284  
Fax  
3%  
5%  
10%  
10%  
MAYCO PARTS  
800-306-2926  
310-537-3700  
Web  
FAX: 800-672-7877  
FAX: 310-637-3284  
Special freight allowances  
when you order 10 or more  
line items via Web or Fax!**  
FedEx Ground Service at no charge for freight  
SERVICE DEPARTMENT  
800-421-1244  
FAX: 310-537-4259  
310-537-3700  
TECHNICAL ASSISTANCE  
800-478-1244  
WARRANTY DEPARTMENT  
800-421-1244, EXT. 279  
310-537-3700, EXT. 279  
FAX: 310-631-5032  
FAX: 310-537-1173  
No other allowances on freight shipped by any other  
carrier.  
NOTE:DISCOUNTSARESUBJECTTOCHANGE  
Direct TOLL-FREE access  
to our Parts Department:  
Toll-free nationwide — 800-427-1244  
MULTIQUIP INC.  
18910 WILMINGTON AVENUE  
POST OFFICE BOX 6254  
CARSON, CALIFORNIA 90749  
310-537-3700•800-421-1244  
FAX:310-537-3927  
E-MAIL:m[email protected]  
WWW:multiquip.com  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 5  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — SPECIFICATIONS  
Table 1. MVH-200DA REVERSIBLE PLATE COMPACTOR SPECIFICATIONS  
Centrifugal Force  
7,056 lbs. (3,200 kg)  
5,200 vpm  
Vibration Frequency  
Maximum Forward Speed  
Plate Size (L x W)  
Operating Weight  
75 ft/min (23 m/min)  
27.6 x 20 in (70 x 51 cm)  
449 lbs. (204 kg)  
Maximum Area Capacity  
HP Rating  
7,515 sq. ft/hr (698 sq. m/hr)  
6.7 BHP (4.9 kW)  
Table 2. Engine Specifications (YANMAR)  
YANMAR  
Engine Make  
Engine Model  
L-70EE-DVMK (Recoil Start)  
Air-cooled 4-cycle Diesel Engine  
3.07 x 2.51 in (78 x 64 mm)  
10.34 fl oz (306 cm3)  
Engine Type  
Cylinder Bore X Stroke  
Displacement  
Maximum Ouput  
6.5 HP @3,600 RPM  
Fuel Tank Capacity  
Oil Capacity  
3.5 quarts (3.31 liters)  
1.16 quarts (1.10 liters)  
Starting Method D/DS  
Dry Net Weight Recoil/Electric  
Dimensions (L x W x H)  
Recoil/Electric  
72.75 lbs. (33 kg)/83.77 lbs. (38 kg)  
15.11 x 16.57 x 17.71 in (384 x 421 x 450 mm)  
PAGE 6 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — DIMENSIONS  
Figure 1. MVH-200DA Reversible Plate Compactor Dimensions  
TABLE 3. DIMENSIONS  
REFERENCE  
DIMENSIONS  
IN. (MM)  
LETTER  
A
B
C
D
E
49 in. (1245 mm.)  
21 in. (533 mm.)  
26.5 in. (673 mm.)  
48 in. (1219 mm.)  
31 in. (787 mm.)  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 7  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — SAFETY MESSAGE ALERT SYMBOLS  
Potential hazards associated with the operation of an  
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!  
MVH-200DA Reversible Plate Compactor will be referenced  
with Hazard Symbols which appear throughout this manual,  
and will be referenced in conjunction with Safety Message  
Alert Symbols.  
Safety precautions should be followed  
at all times when operating this  
equipment. Failure to read and  
understand the Safety Messages and  
Operating Instructions could result in  
injury to yourself and others.  
HAZARD SYMBOLS  
WARNING - Lethal Exhaust Gases  
This Owner's Manual has  
been developed to provide  
complete instructions for the  
safe and efficient operation  
of the Multiquip Model  
MVH-200DA Reversible  
Plate Compactor.  
Engine exhaust gases contain  
poisonous carbon monoxide. This gas  
is colorless and odorless, and can  
cause death if inhaled. NEVER operate  
this equipment in a confined area or  
enclosed structure that does not provide  
ample free flow air.  
Refer to the engine manufacturer’s instructions for data  
relative to its safe operation.  
WARNING - Explosive Fuel  
Before using this reversible plate compactor,ensure that  
the operating individual has read and understands all  
instructions in this manual.  
Diesel fuel is extremely flammable, and  
its vapors can cause an explosion if ignited.  
DO NOT start the engine near spilled fuel  
or combustible fluids.  
SAFETY MESSAGE ALERT SYMBOLS  
DO NOT fill the fuel tank while the engine is running or  
hot. DO NOT overfill tank, since spilled fuel could ignite if  
it comes into contact with hot engine parts or sparks from  
the ignition system. Store fuel in approved containers, in  
well-ventilated areas and away from sparks and flames.  
The three (3) Safety Messages shown below will inform you  
about potential hazards that could injure you or others. The  
Safety Messages specifically address the level of exposure  
to the operator, and are preceded by one of three words:  
DANGER, WARNING, or CAUTION.  
WARNING - Burn Hazards  
DANGER  
You WILL be KILLED or SERIOUSLY INJURED  
Engine components can generate extreme  
heat. To prevent burns, DO NOT touch  
these areas while the engine is running or  
immediately after operations. Never  
operate the engine with heat shields or heat  
guards removed.  
if you DO NOT follow these directions.  
WARNING  
You CAN be KILLED or SERIOUSLY INJURED if  
you DO NOT follow these directions.  
CAUTION - Respiratory Hazard  
ALWAYS wear approved respiratory  
protection when required.  
CAUTION  
You CAN be INJURED if you DO NOT follow  
these directions.  
PAGE 8 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — SAFETY MESSAGE ALERT SYMBOLS  
CAUTION - Rotating Parts  
CAUTION - Equipment Damage Messages  
NEVER operate equipment with covers,  
or guards removed. Keep fingers, hands,  
hair and clothing away from all moving  
parts to prevent injury.  
Other important messages are provided throughout this  
manual to help prevent damage to your light tower, other  
property, or the surrounding environment.  
CAUTION - Accidental Starting  
ALWAYS place the power source, circuit  
breakers or ON/OFF switch in the OFF  
position, when the generator is not in use,  
unless connected to transfer switch.  
This reversible plate compactor,  
other property, or the surrounding  
environment could be damaged  
if you do not follow instructions.  
CAUTION - Sight and Hearing Hazards  
ALWAYS wear approved eye and  
hearing protection.  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 9  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — RULES FOR SAFE OPERATION  
■
NEVER touch the hot exhaust manifold,  
muffler or cylinder.Allowthese parts to cool  
before servicing engine or pump.  
DANGER  
Failure to follow instructions in this manual may lead to  
serious injury or even death! This equipment is to be  
operated by trained and qualified personnel only! This  
equipment is for industrial use only.  
The following safety guidelines should always be used when  
operating the compactor:  
■
■
HighTemperatures – Allow the engine  
to cool before adding fuel or performing service and  
maintenance functions. Contact with hot components can  
GENERAL SAFETY  
■
DO NOT operate or service this equipment before  
readingthisentiremanual.  
cause serious burns.  
The engine of this pump  
requires an adequate  
free flow of cooling air.  
NEVER! operate the  
compactor in any  
enclosed or narrow area  
where free flow of the air  
is restricted. If the air flow  
is restricted it will cause  
■
■
This equipment should not be operated by persons under 18  
years of age.  
NEVER operate this equipment without proper protective  
clothing, shatterproof glasses, steel-toed boots and other  
protective devices required by the job.  
serious damage to the  
compactor or engine and may cause injury to people and  
property.Remember the engine gives off DEADLY gases.  
■
■
NEVER operate this equipment when not feeling  
■
■
ALWAYS refuel in a well-ventilated area, away from sparks  
well due to fatigue, illness or taking medicine.  
and open flames.  
ALWAYS use extreme caution when working with flammable  
liquids. When refueling, stop the engine and allow it to cool.  
DO NOT smoke around or near the machine. Fire or explosion  
could result from fuel vapors, or if fuel is spilled on a hot  
engine.  
NEVER operate this equipment under the influence or drugs or  
alcohol.  
■
NEVER operate the equipment in an  
explosive atmosphere or near  
combustible materials. An explosion or fire  
could result causing severe bodily harm  
or even death.  
■
■
■
Whenever necessary, replace nameplate, operation and  
safety decals when they become difficult read.  
ALWAYS check the machine for loosened threads or bolts  
before starting.  
■
■
■
Topping-off to filler port is dangerous, as it  
tends to spill fuel.  
ALWAYS wear proper respiratory (mask) hearing and eye  
protection equipment when operating the pump.  
Refer to the Engine Owner's Manual for engine technical  
questions or information.  
NEVER use accessories or attachments, which are not  
recommended by Multiquip for this equipment. Damage to  
the equipment and/or injury to user may result.  
■
Manufacturer does not assume responsibility for any accident  
due to equipment modifications.  
PAGE 10 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — RULES FOR SAFE OPERATION  
Loading and Unloading (Crane):  
Maintenance Safety:  
■
Before lifting, make sure that machine parts (hook and  
vibration insulator) are not damaged and screws are not  
loosened or lost.  
■
■
NEVER lubricate components or attempt service on a  
running machine.  
ALWAYS allow the machine a proper amount of time to  
■
Always make sure crane or lifting device has been properly  
secured to the hook of guard frame on compactor.  
cool before servicing.  
■
■
Keep the machinery in proper running condition.  
■
■
■
■
NEVER lift the machine while the engine is running.  
Use adequate lifting cable (wire or rope) of sufficient strength.  
Use one point suspension hook and lift straight upwards.  
Fix damage to the machine immediately and always replace  
broken parts.  
■
Dispose of hazardous waste properly. Examples of  
potentially hazardous waste are used motor oil, fuel and  
fuel filters.  
NEVER allow any person or animal to stand underneath the  
machine while lifting.  
■
Try not to lift machine to unnecessary heights.  
■
■
DO NOT use food or plastic containers to dispose of  
hazardous waste.  
TRANSPORTING  
DO NOT pour waste, oil or fuel directly onto the ground,  
down a drain or into any water source.  
■
■
ALWAYS shutdown engine before transporting.  
Tighten fuel tank cap securely and close fuel cock to prevent  
fuel from spilling.  
Emergencies  
■
■
Drain fuel when transporting compactor over long distances  
or bad roads.  
■
ALWAYS know the location of the  
nearest fire extinguisher.  
ALWAYS tie down the compactor during transportation by  
securing the compactor's guard frame with rope.  
■
■
ALWAYS know the location of the nearest  
first aid kit.  
In emergencies always know the location of the  
nearest phone or keep a phone on the job site.  
Also know the phone numbers of the nearest  
ambulance, doctor and fire department. This  
information will be invaluable in case of an  
emergency.  
Figure 18. Lifting the Compactor  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — OPERATION AND SAFETY DECALS  
Figure 2 displays the operation and safety decals as they appear on the reversible plate compactor. Should any of these decals  
become damaged or unreadable, contact the Multiquip Parts Department for a replacement set.  
Figure 2. Operation and Safety Decals  
PAGE 12 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — FEATURES  
Frequency/Speed  
Plate Compactor  
The compactor's vibrating plate maximum frequency is 5200  
vpm (vibrations per minute).The forward and reverse travel speed  
of the compactor is approximately 75 ft./minute (23 meters/  
minute).  
The Mikasa MVH-200DA is a walk-behind, reversible plate  
compactor designed for the compaction of sand, clay and asphalt.  
This plate compactor is a powerful compacting tool capable of  
applying a tremendous force in consecutive high frequency  
vibrations to a soil surface. Its applications include soil compacting  
for road, embankments and reservoirs as well as backfilling for  
gas pipelines, water pipelines and cable installation work.  
Engine  
The Mikasa MVH-200DA Plate Compactor is equipped with an  
air-cooled, 4-stroke, single-cylinder YANMAR L70EE-DVMK  
diesel engine.  
Vibratory Plates  
The vibratory plates of the MVH-200DA produce low amplitude  
high frequency vibrations, designed to compact granular soils.  
Controls  
Before starting the MVH-200DA Plate Compactor, identify and  
understand the function of the controls and components as  
indicated in Figure 3.  
The resulting vibrations cause forward motion.The engine and  
handle are vibration isolated from the vibrating plate.The heavier  
the plate, the more compaction force it generates.  
ReversibleVibratory Plates  
Reversible vibratory plates have two eccentric weights that allow  
a smooth transition for forward and reverse travel, plus increased  
compaction force as the result of dual weights.  
Due to their weight and force, reversible plates are ideal for  
semi-cohesive soils.  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — PLATE COMPACTOR COMPONENTS  
Figure 3. MVH-200DA Components  
Figure 3 illustrates the location of the major components for the 6. Engine –This plate compactor uses a YANMAR L70EE-  
MVH-200DA Reversible Plate Compactor.The function of each  
component is described below:  
DVMK engine. Refer to the owner’s manual for engine  
information and related topics.  
1.  
Hand Grip – When operating the compactor use this hand 7. Belt Cover – Remove this cover to gain access to the V-  
grip to maneuver the compactor.  
belts.NEVER run the compactor without theV-belt cover.If  
the V-belt cover is not installed, the possibility exists that  
your hand may get caught between the V-belt and clutch,  
thus causing serious injury and bodily harm.  
2.  
Forward & Reverse Lever – Push the lever forward, the  
compactor will move in a forward direction, pull the lever  
backwards, the compactor will move in backwards direction.  
Placing the lever in the middle (midway) will cause the 8. Base Plate – Designed to compact sand, clay, and asphalt.  
compactor not to move (neutral).  
9. OilTank – Fill with proper grade of engine oil.  
3.  
Handle Bar –When operating the compactor, this handle  
is to be in the downward position.When the compactor is  
to be stored, move the handle bar to the upright position.  
10. Vibration Case – Encloses the eccentric, gears and  
counter weights.  
11. Shock Absorber – Protects plate compactor from damage  
4.  
5.  
Guard Hook - Used to lift the machine with crane or other  
lifting device.  
by absorbing vibration during operation.  
12. Throttle Lever – Controls the speed of the plate compactor.  
Stopper - Locks the handle in place in the upward position  
for stowing.  
Place straight vertically to start, push fully counterclockwise  
for full throttle and fully clockwise to stop plate compactor.  
PAGE 14 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — ENGINE COMPONENTS  
Figure 4. Engine Controls and Components  
6.  
Recoil Starter– Manual-starting method. Pull the starter  
grip until resistance is felt, then pull briskly and smoothly.  
The engine shown above is a YANMAR L70EE- DVMK engine  
(Figure 4). The engine must be checked for proper lubrication  
and filled with fuel prior to operation. Refer to the manufacturer’s  
engine manual for instructions and details of operation and  
servicing. Each component is described below:  
7.  
Oil Filler Cap / Dipstick – Remove this cap to add oil to the  
engine crankcase. Read dipstick to determine if oil level is  
low. DO NOT over fill.  
Operating the engine without  
an air filter, with a damaged  
air filter, or a filter in need of  
1.  
Fuel Filler Cap – Remove this cap to add unleaded  
gasoline to the fuel tank. Make sure cap is tightened  
securely.DO NOT over fill.  
replacement will allow dirt to  
enter the engine, causing  
rapid engine wear.  
CAUTION - FuelingThe Engine  
Adding fuel to the tank should be done only  
when the engine is stopped and has had an  
opportunity to cool down. In the event of a fuel  
spill, DO NOT attempt to start the engine until  
the fuel residue has been completely wiped  
up, and the area surrounding the engine is dry.  
8.  
9.  
Oil Drain Plug – Unscrew plug to drain oil from engine  
crankcase.Dispose of oil in a safe manner.  
Decompression Lever– Press down before starting  
engine.To prevent damage to engine, DO NOT use for any  
other purpose.  
CAUTION - Burn Hazard  
2. Fuel Tank – Capacity is 3.5 quarts (3.31 liters) of diesel  
fuel.  
Enginecomponentscangenerateextremeheat.  
To prevent burns, DO NOT touch these areas  
while the engine is running or immediately after  
operating. NEVER operate the engine with the  
muffler removed.  
3. Air Cleaner – Prevents dirt and other debris from entering  
the fuel system. Remove wing-nut on top of air filter  
cannister to gain access to filter element.  
4. Muffler – Used to reduce noise and emissions.  
5. Recoil Starting Handle (pull rope) – Type of engine  
starting method.  
10. Fuel Cock– Controls the flow of diesel fuel to the carburetor.  
Must be in the ON position when starting and running the  
engine.  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — PRE-INSPECTION  
3. Insertandremovethedipstickwithoutscrewingitintothefiller  
neck. Check the oil level shown on the dipstick.  
CAUTION - General Safety Precautions  
4. If the oil level is low (Figure 6), fill to the edge of the oil filler  
holewiththerecommendedoiltype(Table4).Maximum oil  
capacity is 1.16 quarts (1.1 liters).  
NEVER operate the compactor in a confined  
area or enclosed area structure that does not  
provide ample free flow of air.  
ALWAYS wear approved eye and hearing  
protection before operating the compactor.  
Before Starting:  
1.  
Read safety instructions at the  
beginning of manual.  
Figure 6. Engine Oil Dipstick (Oil Level)  
Table 4. Oil Type  
2.  
Remove dirt and dust, particularly  
in the engine cooling air inlet,  
carburetor and air cleaner.  
3.  
4.  
5.  
Check the air filter for dirt and dust.  
If air filter is dirty, replace air filter with a new one as required.  
Season  
Summer  
Spring/Fall  
Winter  
Temperature  
25°C or Higher  
25°C~10°C  
Oil Type  
SAE 10W-30  
SAE 10W-30/20  
SAE 10W-10  
Check carburetor for external dirt and dust.Clean with dry  
compressed air.  
Check fastening nuts and bolts for tightness.  
0°C or Lower  
Engine Oil Check:  
1.  
To check the engine oil level, place the compactor on secure  
level ground with the engine stopped.  
WARNING - Explosive Fuel  
Explosive Fuel  
Diesel is extremely flammable, and its vapors  
can cause an explosion if ignited. DO NOT  
start the engine near spilled fuel or  
combustible fluids. DO NOT smoke while  
refueling.DO NOT attempt to refuel the pump  
if the engine is hot! or running.  
2.  
Remove the filler dipstick from the engine oil filler hole  
(Figure 5) and wipe clean.  
Fuel Check:  
1. Remove the diesel cap located on top of fuel tank.  
2. Visually inspect to see if the fuel level is low. If fuel is low,  
replenish with unleaded fuel.  
3. Whenrefueling,besuretouseastrainerforfiltration.DONOT  
top-off fuel.Wipe up any spilled fuel immediately!  
Figure 5. Engine Oil Dipstick (Removal)  
PAGE 16 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — START-UP PROCEDURE  
This section is intended to assist the operator with the initial  
start-up of the compactor. It is extremely important that this  
section be read carefully before attempting to use the compactor  
in the field.  
4. Push down the decompression lever (Figure 10) and re-  
lease.  
Starting the Engine (Yanmar engine):  
1. Open the fuel cock (Figure 7).  
Figure 10. Decompression Lever  
5. If the engine does not start, repeat steps 3 and 4.  
Shut-Down Procedure:  
1. Return the throttle lever to the START position. Allow the  
Figure 7. Fuel Cock  
machine to cool down for 2 to 3 minutes.  
2. Turn the throttle lever to the STOP position (Figure 11) to  
2.  
Move the throttle lever to the START position by opening it  
to about 20 degrees (Figure 8).  
stop the engine.  
Figure 11. Throttle Lever (Stop)  
Figure 8. Throttle Lever (Start Position)  
3. Close the fuel cock (Figure 7).  
3. Grasp the starter grip (Figure 9) and slowly pull it out.The  
resistancebecomesthehardestatacertainposition,corre-  
spondingtothecompressionpoint.Pullthestartergripbriskly  
andsmoothlyforstarting.  
Figure 9. Starter Grip  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — OPERATION  
To Turn The Compactor:  
Emergency Shutdown Procedure:  
1. Move the travel lever to the NEUTRAL position.  
1. Move the throttle lever quickly to the STOP position  
(Figure 11).  
2. Holdthehandgripfirmlyandturnthecompactorinthedesired  
direction.DONOTswingcompactorwhilegrippingthetravel  
lever.  
2. Close the fuel cock.  
Traveling:  
Wheneverthecompactor'svibra-  
1. Graspthecompactor'shandgripandmovethethrottlelever  
(Figure12)quicklytothefastposition.Thecompactorwillnot  
operate correctly until the engine speed is high enough to  
engage the centrifigal clutch (approximately 2300 RPMs).  
tion becomes weak or lost during  
normal operation, regardless of  
operation hours, check theV-belt  
andclutchimmediately.  
Adjusting Handle Height:  
The height of the handle is adjustable for your comfort .  
1. Loosen the butterfly screw (Figure 14).  
2. Turn the grip clockwise to raise the handle or counterclock-  
wise to lower the handle.  
3. When the handle is raised to the desired height, tighten the  
butterflyscrew.  
Figure 12. Throttle Lever (Fast)  
Always move the throttle lever  
quickly without hesitation,  
because increasing the engine  
speed slowly causes the clutch  
to slip.  
2. To make the compactor travel forward, push the travel lever  
forward(Figure13).Tomakethecompactortravelbackward,  
pull the travel lever back (Figure 13).  
Figure 14. Handle Adjustment  
Figure 13. Travel Lever  
5. Slowlywalkbehindthecompactorandbeonthelookout for  
anylargeobjectsorforeignmatterthatmightcausedamage  
to the compactor or bodily injury.  
6. Iftravelleverisplacedintheneutralposition,themachinewill  
vibrate in place.  
PAGE 18 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — OPERATION  
Stowing the Handle:  
Lifting:  
1. Push up the handle (Figure 15).  
1. Use a crane or lift to load and unload the machine. A skilled  
crane operator is required to perform the job.  
2. Pull the stopper grip upward into the hole of the guard frame  
to lock the handle.  
2. When lifting the machine, check for any damaged or loose  
bolts, lifting hooks, and shock mounts.  
3. Check any damaged or loose bolts in the guard frame to  
avoid machine sliding off.  
4. Make sure that the machine is shut off before machine is  
lifted.  
5. Use reliable cable for lifting.  
6. Always lift the machine vertically and keep the machine away  
from workers and animals.  
7. Do not lift the machine higher than the required height.  
Transporting:  
1. Always make sure that the machine is shut off while being  
transported.  
2. Check that the fuel cap is properly closed and tightened.  
3. When traveling long distances or on rugged terrain, drain the  
fuel of the machine before transporting.  
Figure 15. Stowing the Handle  
4. Tie down the machine securely on the transportation so that  
it will not move or topple over.  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — MAINTENANCE  
CAUTION - General Maintenance Safety  
TABLE 6. MVH-200DA ENGINE CHECK  
Inspection and other services should always be carried out  
on hard and level ground with the engine shutdown.  
ITEM  
HOURS OF OPERATION  
Oil or Fuel Leak  
Every 8 hours (every day)  
Every 8 hours (every day)  
Inspection and Maintenance ServiceTables.  
Tightness of Fastening  
Threads  
To make sure your plate compactor is always in good working  
condition before using, carry out the maintenance inspection in  
accordance with Tables 5 through 7.  
Every 8 hours (every day)  
(Replenish to specified maximum  
level)  
Engine Oil Check and  
Replenishment  
TABLE 5. MVH-200DA MACHINE INSPECTION  
After first 25 hours then every 50 to  
100 hours  
HOURS OF  
OPERATION  
Engine Oil Replacement  
Air Filter Cleaning  
ITEM  
REMARKS  
Loose or Missing  
Screws  
Every 8 hours  
(every day)  
Every 100 hours  
See separate engine manual for details on engine check.  
Every 8 hours  
(every day)  
Damaged Parts  
Daily Service  
Function of Controlling Every 8 hours  
System Part (every day)  
z
z
Check for leakage of fuel or oil.  
Check for loose screws including tightness. See Table 7  
below (tightening torque ), for retightening:  
Hydraulic System Leak Every 100 hours  
Vibrator Oil Check  
Every 100 hours See page 21  
Every 300 hours See page 21  
Every 100 hours See page 23  
TABLE 7.  
Vibrator Oil  
Replacement  
TIGHTENING TORQUE (in. kg/cm) Diameter  
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm 20mm  
Hydraulic Oil Check  
4T  
70  
150  
250  
400  
300  
500  
800  
500  
800  
750  
1,100 1,400  
2,000  
3,800  
5,600  
6-8T  
11T  
100  
150  
1,300 2,000 2,700  
First after 200  
hours, then every See page 23  
1,000 hours  
Hydraulic Oil  
Replacement  
1,200 2,000 2,900 4,200  
300~ 650 ~  
350 700  
*
100  
V-belt (clutch) Check Every 200 hours See page 22  
* (In case counter-part is of aluminum)  
(Threads in use with this machine are all right handed)  
Material and quality of material is marked on each bolt, and screw.  
These inspection intervals are for  
operation under normal conditions.  
Adjust your inspection intervals  
based on the number hours plate  
compactor is in use, and particular  
working conditions. Fuel piping and  
connections should be replaced  
every 2 years.  
z
z
Remove soil and clean the bottom of compaction plate.  
Check hydraulic pump, piping and hose for any leakage. A  
loosened hydraulic hose can be a cause for leakage. Check  
hydraulic hose connections with wrench applied for  
tightness.  
z
Check engine oil.  
PAGE 20 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — MAINTENANCE  
3. Clean foam element in warm, soapy water or nonflammable  
solvent. Rinse and dry thoroughly. Dip the element in clean  
engineoilandcompletelysqueezeouttheexcessoilfromthe  
element before installing.  
Engine Oil Replacement:  
1. Replace engine oil, first in 25 hours of operation and every  
50 to 100 hours afterwards.  
2. Drain the engine oil when the oil is warm as shown in  
Figure 16.  
Figure 17. Engine Air Filter  
Hydraulic Oil  
Figure 16. Engine Oil (Draining)  
1. Check hydraulic oil in every 100 hours of operation. With  
handle bar positioned vertically (storage position), remove  
oil level check plug (Figure 18) from the top of hydraulic  
pump and check for proper oil level.  
3. Removetheoildrainboltandsealingwasherandallowthe  
oil to drain into a suitable container.  
4. Replace engine oil in the oil tank with recommended type  
oil as listed in Table 4. Engine oil capacity is 1.16 quarts  
(1.1 liter). DO NOT overfill.  
2. Replace hydraulic oil after first 200 hours and in every 1,000  
hours of operation.  
5. Install drain bolt with sealing washer and tighten securely.  
Air Filter:  
1. Remove the air cleaner cover and foam filter element as  
shown in Figure 17.  
2. Tapthepaperfilterelement(Figure 17)severaltimesonahard  
surfacetoremovedirt,orblowcompressedair[notexceeding  
30psi(207kPa,2.1kgf/cm2)]throughthefilterelementfromthe  
air cleaner case side.  
CAUTION - Cleaning the Engine Air Filter  
Figure 18. Oil Level Check Plug  
NEVER brushoffdirt.Brushingwillforcedirtintothefibersand  
causepoorperformanceinyourairfilter.Replacethepaperfilter  
element if it is excessively dirty.  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — MAINTENANCE  
Checking and Replacing theV-Belt and Clutch:  
Checking the Clutch  
After 200 hours of operation, remove the belt cover to check the  
V-belt tension (Figure 19).  
1. With belt cover removed, visually check outer drum of the  
clutch for seizure and "V" groove for wear or damage.  
2. Clean the "V" groove as necessary.  
3. Check the clutch lining and shoe for signs of wear. If the shoe  
is worn, replace the clutch to prevent deficient power  
transmission and slippage.  
Replacing the Clutch  
1. RemoveV-belt.  
2. Remove bolt at engine power output by giving a shock to an  
engaged wrench (e.g. tapping with hammer) and rotate the  
bolt counterclockwise.  
Figure 19. V-Belt Check  
CAUTION - Checking and Replacing theV-Belt  
3. Remove clutch with a pulley extractor.  
4. To install a new clutch, reverse steps 1-3.  
NEVERattempttochecktheV-beltwith  
the engine running. Severe injury can  
occurifyourhandgetscaughtbetween  
the V-belt and the clutch. Always use  
safetygloves.  
Vibrator Oil Level Check  
CAUTION - Checking and Replacing theV-Belt  
Always clean the area around the vibrator oil level check hole  
beforeremovingoilcheckplug.Thiswillpreventdirtanddebris  
fromenteringthesystem.  
Checking theV-belt  
1. Tension is proper if the belt bends about 10 mm when  
depressed strongly with finger between shafts. Loose or worn  
V-belts reduces power transmission efficiency, causing weak  
compaction and reduces the life of the belt itself.  
1. In every 100 hours of operation, with the machine positioned  
horizontally, remove vibrator oil level check plug  
(Figure 20) off vibrator (19 mm wrench) and see if oil is up to  
filler port.Be sure to clean area around check hole to prevent  
dirt and dust from entering.  
Replacing theV-belt  
1. Remove the belt cover.  
2. In every 300 hours of operation, replace oil (capacity 1,500  
cc). For draining oil through level check hole, have the  
machine inclined with a sleeper or the like placed under the  
compaction plate on opposite side.  
2. Engage an offset wrench (19 mm) or the like to vibrator pulley  
(lower) fastening bolt.  
3. Engage waste cloth or the like at midway ofV-belt on the left  
side and while pulling it back strongly, rotate the offset wrench  
clockwise so that theV-belt will come off.  
* Use engine oil 10W-30 for this lubrication.  
4. Check the clutch and replace as necessary, following the  
procedures listed in Checking the Clutch.  
5. EngageV-belt to lower vibrator pulley and push theV-belt to  
the left side of the upper clutch and the rotate offset wrench  
clockwise so that theV-belt moves onto the pulley.  
Figure 20. Vibrator Oil Maintenance  
PAGE 22 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — MAINTENANCE  
CAUTION - Filling the Hydraulic Oil Reservoir  
Make sure hydraulic oil i is at a normal safe operating level.  
DO NOT over fill. Over filling (excessive oil) will cause excess  
oil to blow out of breather plug.  
Replacing Hydraulic Oil  
1. Remove the hydraulic hoses (left and right) which enters the  
cylinder of the vibrator from the hydraulic pump and move  
the travel lever back and forth to drain the hydraulic oil from  
the pump.  
2. After draining, reinstall the hydraulic hoses and lock the travel  
lever to the sub-handle at reverse side (at MAXIMUM  
position), using a rope.  
3. Remove the reservoir cover at the top of the pump (Figure 21).  
Remove the bleed valve assembly within the pump using a  
17 mm box wrench.  
Figure 22. Hydraulic System  
5. Filling the forward travel circuit with oil.  
a. With the rope removed from the travel lever, move the  
lever slowly up and down while adding oil into the hand  
pump. Use Shell Tellus Oil #46 or equivalent.  
b. Moving it about 10 times causes the forward resistance to  
increase. When the resistance has considerably  
increased, with the travel lever remaining on the reverse  
side, install the bleed valve assembly loosely inside the  
pump to prevent oil splash.  
c. Push the travel lever forward all the way.The valve inside  
the spool will activate to push out the aerated oil reverse  
circuit.  
d. With the bleed valve assembly removed, repeat step c,  
two to three times.  
Figure 21. Hydraulic Oil Maintenance  
CAUTION - Removing the BleedValve  
Whenremovingthebleedvalve,NEVERloosentheM8nuton  
itsend. Acopperpackingisusedunderneaththebleedvalve,  
thereforecareshouldbetakennottodropitintothepump.Make  
sure to remove it together with the bleed valve.DO NOT allow  
dust or trash to enter the hand pump.  
4. Remove bleed plug at the cylinder of the vibrator (right belt  
cover side, forward travel circuit) (Figure 22). After a while, oil  
will flow out of the bleed plug. When aeration disappears,  
reinstall the plug, tightening it securely.  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — MAINTENANCE  
6. Filling the reverse travel circuit with oil.  
Explosive Fuel  
DANGER  
a. With the travel lever pushed forward (hydraulic circuit is  
connected with reverse travel circuit), add oil into pump  
and remove bleed plug of vibrator cylinder (opposite of  
belt cover side). In a few seconds, oil will come out of  
bleed plug.  
Diesel fuel is highly flammable and can be dangerous if  
mishandled. DO NOT smoke while refueling. DO NOT attempt  
to refuel the compactor if the engine is hot! or running.  
b. When aeration disappears, reinstall the plug tightly.  
c. Move the travel lever slowly until aeration in the hand  
pump disappears (about 10 to 15 times).  
Checking The Fuel  
1. Remove the fuel cap located on top of fuel tank.  
2. Visuallyinspecttoseeiffuellevelislow. Iffuelis low,replenish  
with diesel fuel (Figure 23).  
7. When the aeration in the pump disappears, with the travel  
lever pushed forward, reinstall the valve. Be careful not to  
drop the packing into pump. The bleeding valve tightening  
torque is 450 to 500 kg-gm.  
3. Whenrefueling,besuretouseastrainerforfiltration.DONOT  
8. After installing the bleed valve, moving the travel lever all the  
way to reverse causes excess oil to be discharged into pump.  
If valve fails to activate, aeration still remains in the circuit.  
With the bleed valve removed, operate travel lever again to  
bleed. If valve is activated, move the travel lever forward to  
activate the valve inside spool before moving it to reverse to  
activate the bleed valve. Repeat 3 to 4 times.  
top-off fuel. Wipe up any spilled fuel.  
9. After making sure that the hydraulic oil in the pump is at the  
specified level, reinstall the reservoir cover. Coat both sides  
of packing with liquid packing (such as Threebond #1215).  
CAUTION - Overfilling the Hydraulic Oil  
Figure 23. Refueling  
DANGER  
Reservoir  
Make sure that hand pump is filled with hydraulic oil to the  
specified level. Excessive oil may hinder bleed valve function,  
resulting in poor reverse performance.  
Fuel spillage on a hot engine can cause a fire or explosion.  
If fuel spillage occurs, wipe up the spilled fuel completely to  
prevent fire hazards. NEVER! smoke around or near the  
compactor.  
10.After adding oil and reinstalling the reservoir cover, operate  
the travel lever to make sure of the following:  
a. spool valve: when pushed forward, resistance is felt in  
two-stage motion.  
PAGE 24 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — ENGINETROUBLESHOOTING  
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a  
breakdown, please take remedial action following the diagnosis based on the Engine Troubleshooting Table (Table 8)  
information shown below and on the following page. If the problem cannot be remedied, please leave the unit as it is  
and consult Multiquip’s business office or service plant.  
TABLE 8. ENGINE TROUBLESHOOTING  
SYMPTOM  
POSSIBLE PROBLEM  
Speed control lever is in "STOP" position?  
No fuel reaching injection pump?  
Defective fuel pump?  
SOLUTION  
Set speed control lever to "START" position.  
Add fuel. Check entire fuel system.  
Replace fuel pump.  
Fuel filter clogged?  
Replace fuel filter and clean tank.  
Replace or repair fuel line.  
Faulty fuel supply line?  
Engine will not start or start is  
delayed, although engine can  
be turned over.  
Check piston, cylinder and valves. Adjust or  
repair per engine repair manual.  
Compression too low?  
Repair or replace injector in accordance with  
engine repair manual.  
Fuel injector not working correctly?  
Oil pressure too low?  
Check engine oil pressure.  
Comply with cold starting instructions and  
proper oil viscosity.  
Low starting temperature limit exceeded  
Check whether clear (not turbid) fuel emerges  
from the fuel line (detach from injection  
pump). If the fuel is turbid or separated, warm  
up the engine or drain the complete fuel  
supply system. Refuel with winter grade diesel  
fuel.  
Fuel separates has inadequate resistance to  
low temperatures?  
At low temperatures engine will  
not start.  
Refill engine crankcase with correct type of oil  
for winter environment.  
Engine oil too thick?  
Throttle lever in STOP position?  
Fuel filter blocked?  
Reposition throttle lever to RUN position.  
Replace fuel filter.  
Engine fires but stops soon as  
starter is switched off.  
Fuel supply blocked?  
Fuel tank empty?  
Check the entire fuel system.  
Add fuel.  
Engine stops by itself during  
normal operation.  
Fuel filter blocked?  
Replace fuel filter.  
Fuel tank empty?  
Fill with No.2 diesel fuel.  
Replace fuel filter.  
Fuel filter clogged?  
Low engine power, output and  
speed.  
Fuel tank venting is inadequate?  
Ensure that tank is adequately vented.  
See engine manual for corrective action.  
Speed control lever does not remain in  
selected position?  
Engine oil level too full?  
Air filter blocked?  
Correct engine oil level?  
Clean or replace air filter.  
Adjust valves per engine specification.  
See engine manual.  
Low engine power output and  
low speed, black exhaust  
smoke.  
Incorrect valve clearances?  
Malfunction at injector?  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — PLATE COMPACTORTROUBLESHOOTING  
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a  
breakdown, please take remedial action following the diagnosis based on the Compactor Troubleshooting Table  
(Table 9) information shown below. If the problem cannot be remedied, please leave the unit as it is and consult Multiquip’s  
business office or service plant.  
TABLE 9. PLATE COMPACTOR TROUBLESHOOTING  
SYMPTOM  
POSSIBLE CAUSE  
Engine speed too low?  
SOLUTION  
Set engine speed to correct RPM.  
Check or replace clutch.  
Clutch slips?  
Travel speed too low, and vibration is  
weak.  
V-belt slips?  
Adjust or replace V-belt.  
Excessive oil in vibrator?  
Drain excess oil and fill to proper level.  
Check eccentric, gears and counter  
weights.  
Malfunction in vibrator housing?  
Directional components defective?  
Reversing lever adjustment?  
Check all directional components  
Adjust or repair reversing lever.  
Repair or replace hydraulic oil hose.  
Bleed hydraulic oil system.  
Hydraulic oil hose broken?  
Travels forward or reverse, but  
impossible to switch direction.  
Aeration in hydraulic oil for reversing system?  
Clean or replace hand pump check  
valve.  
Check valve in hand pump clogged with dust?  
Piston or bearing in cylinder (vibrator assy.) is  
defective?  
If worn, replace cylinder piston or  
bearing.  
V-belt slips?  
Clutch slips?  
Replace V-belt.  
Check clutch springs and shoes.  
Does not travel either forward or  
reverse.  
Check vibrator housing (eccentric,  
gears and counterweights)  
Vibrator locked?  
If worn, replace cylinder piston or  
bearing.  
Piston or bearing in cylinder defective?  
Air in hydraulic line?  
Bleed hrdraulic oil system.  
Travel lever operating resistance great.  
If worn, replace cylinder piston or  
bearing.  
Piston or bearing in cylinder defective?  
PAGE 26 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
EXPLANATION OF CODE IN REMARKS COLUMN  
How to read the marks and remarks used in this parts book.  
If more than one of the same  
reference number is listed, the last  
one listed indicates newest (or  
latest) part available.  
NOTE  
Items Found In the“Remarks” Column  
Serial Numbers-Where indicated, this indicates a serial number  
range (inclusive) where a particular part is used.  
Model Number-Where indicated, this shows that the  
corresponding part is utilized only with this specific model number  
or model number variant.  
Items Found In the “Items Number” Column  
All parts with same symbol in the number column, , #,  
+, %, or  
*
>
, belong to the same assembly or kit.  
The contents of this parts catalog  
are subject to change without  
notice.  
NOTE  
PAGE 28 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
SUGGESTED SPARE PARTS  
MQ MIKASA MVH-200DA  
1 to 3 Units  
W/ YANMAR L70EE- DVMK  
Qty.  
P/N  
Description  
3 ......... 070200323 ....... V-BELTS  
2 ......... 956100038 ....... THROTTLE WIRE  
3 ......... 11465012591 ... ELEMENT, A/C  
1 ......... 11428855041 ... CAP, FUEL TANK  
1 ......... 11487076630 ... ROPE, RECOIL STARTER  
2 ......... 11425035110 ... STRAINER, OIL LUB W/ O-RING  
2 ......... 11425055121 ... FILTER, FUEL OIL  
1 ......... 11425055100 ... FILTER, FUEL STRAINER  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — DECAL PLACEMENT  
BODY ASSY.  
PAGE 30 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — DECALS PLACEMENT  
BODY ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
PART NAME  
DECAL, OIL TANK  
QTY.  
REMARKS  
920203260  
920204230  
920203330  
920202220  
920204580  
920204040  
920203290  
920203560  
920206280  
920206290  
TBD  
1
1
1
1
1
1
1
1
1
DECAL, TRAVEL LEVER OP.  
DECAL, EAR PROTECTION  
DECAL, FORWARD/REVERSE  
DECAL, FULLTHROTTLE  
DECAL, LIFTING CAUTION  
DECAL, CAUTION OPERATION  
DECAL, ENGINE MAX SPEED  
DECAL, PINCH POINT DANGER  
9
10  
11  
12  
13  
DECAL, READ MANUAL CAUTION 1  
DECAL, MULTIQUIP  
DECAL, V-BELT  
1
1
920206880  
PLATE, SERIAL NO. ........................ 1 ............. CONTACT PARTS DEPARTMENT  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — BODY ASSY.  
BODY ASSY.  
PAGE 32 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — BODY ASSY.  
BODY ASSY.  
NO  
1
2
3
4
5
6
9
PART NO  
PART NAME  
VIBRATING PLATE  
BASE  
SHOCK ABSORBER 75  
NUT M12  
QTY.  
1
1
4
4
8
4
1
4
4
4
1
4
4
4
1
1
1
1
1
1
1
1
5
5
5
1
1
1
1
4
4
1
1
1
REMARKS  
455109250  
455116690  
939010050  
020312100  
030212300  
001221240  
914410012  
001221040  
030210250  
031110160  
455113800  
001220830  
030208200  
031108160  
455434940  
455340680  
951406790  
455445510  
001220835  
030208200  
070200323  
455113750  
001220852  
030208200  
031108160  
953405270  
953405260  
455455570  
455116700  
001221230  
030212300  
455215250  
959406800  
020306050  
SW M12  
BOLT 12 X 40 T  
ENGINE ASSY. L70EE- DVMK  
BOLT 10 X 40 T  
SW M10  
10  
11  
12  
20  
21  
22  
23  
24  
26  
27  
28  
29  
30  
31  
32  
33  
34  
35  
36  
37  
38  
39  
40  
41  
50  
52  
53  
PW M10  
BELT COVER, IN  
BOLT 8 X 30 T  
SW M8  
PW M8  
COVER SEAL  
CLUTCH ASSY.W/ COVER  
KEY7X7X36  
WASHER  
BOLT 8X35 T  
SW M8  
V-BELT B-32 BLUE/HDPF532  
BELT COVER  
BOLT 8X60 T  
SW M8  
PW M8  
PLUG 1/4X14 13L  
PACKING 1/4, CU  
CLUTCH SPACER  
GUARD FRAME  
BOLT 12X30 T  
SW M12  
COVER GUARD  
NUT M6  
NUT M6  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA —VIBRATION ASSY.  
VIBRATION ASSY.  
PAGE 34 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA —VIBRATION ASSY.  
VIBRATION ASSY.  
NO  
51  
52  
53  
54  
55  
61  
62  
63  
64  
65  
66  
66  
67  
68  
69  
69  
70  
71  
72  
73  
73  
74  
75  
76  
77  
73  
73  
74  
75  
76  
77  
78  
79  
80  
81  
82  
83  
84  
95  
PART NO  
PART NAME  
QTY.  
1
6
REMARKS  
455109310  
001221268  
001221240  
030212300  
031112230  
047920050  
455324830  
455324840  
025510063  
455324850  
455435020  
455435020  
455435030  
455435040  
080100300  
080100300  
041006000  
080200100  
455435051  
455010010  
455010070  
080100260  
455324860  
455326060  
050100850  
455010010  
455010070  
080100260  
455324860  
455326060  
050100850  
001220825  
030208200  
031108160  
001200810  
953404600  
040006910  
455010020  
031108160  
VIBRATING CASE  
BOLT 12X140 T  
BOLT 12X40 T  
4
SW M12  
PW M12  
ROLLER BEARING NJ210MC4  
ROTARY SHAFT, DRIVEN  
PISTON ROD  
KNOCK PIN 10X63  
GEAR, DRIVEN  
COLLAR 17X30X3..................................... 4 ................. S/N Z1348 AND BELOW  
COLLAR 17X30X3..................................... 2 ................. S/N Z1349 AND ABOVE  
SPRING 28.2D-41L ................................... 1 ................. S/N Z1348 AND BELOW  
SPRING 27.3D-79L ................................... 1 ................. S/N Z1349 AND ABOVE  
STOP RING R-30 ...................................... 2 ................. S/N Z1348 AND BELOW  
STOP RING R-30 ...................................... 1 ................. S/N Z1349 AND ABOVE  
10  
10  
4
1
1
1
1
BEARING 6000Z  
STOP RING S-10  
4
2
PISTON, 22.4D ......................................... 2 ................. REPLACES 455435050  
PACKING UPH-20308 ............................... 2 ................. S/N W1011 AND BELOW  
PACKING USH-22.4 X 30 X 5 ................... 2 ................. S/N W1012 AND ABOVE  
STOP RING R-26  
CYLINDER, R  
CYLINDER, L  
O-RING G-85  
PACKING UPH-20308  
PACKING USH-22.4 X 30 X 5  
STOP RING R-26  
CYLINDER, R  
CYLINDER, L  
O-RING G-85  
2
1
1
2
2
2
2
1
1
2
8
8
8
2
2
2
2
4
BOLT 8 X 25 T  
SW M8  
PW M8  
BOLT 8 X 10  
COPPER PACKING 8 X 16 X 2  
BEARING 6910  
ELBOW 45' 15-0404  
PW M8  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA —VIBRATION ASSY. (CONT.)  
VIBRATION ASSY. (CONT.)  
PAGE 36 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA —VIBRATION ASSY. (CONT.)  
VIBRATION ASSY. (CONT.)  
NO  
86  
86  
87  
87  
88  
89  
90  
91  
92  
93  
94  
96  
96  
97  
98  
98  
PART NO  
PART NAME  
QTY.  
REMARKS  
455324870  
455331070  
951404500  
951405370  
455324880  
080200500  
060105030  
455324890  
050100850  
001220825  
030208200  
455324900  
455335560  
951403090  
455435060  
455448970  
001221230  
030212300  
455324910  
001521225  
001521240  
952405480  
ROTARY SHAFT, DRIVE ........................... 1 ................. S/N 1540 AND BELOW  
ROTARY SHAFT, DRIVE ........................... 1 ................. S/N A1541 AND ABOVE  
KEY 15 X 10 X 40 RR .............................. 1 ................. S/N 1540 AND BELOW  
KEY 15 X 10 X 39 RR .............................. 1 ................. S/N A1541 AND ABOVE  
GEAR, DRIVE  
STOP RING S-50  
OIL SEAL SB-50729  
BEARING COVER  
O-RING G-85  
BOLT 8 X 25 T  
SW M8  
PULLEY, B1-85D ....................................... 1 ................. S/N 1975 AND BELOW  
PULLEY, B1 W/FAN .................................. 1 ................. S/N D1976 AND ABOVE  
KEY 12 X 8 X 26  
1
2
1
1
1
4
4
1
WASHER, PULLEY ................................... 1 ................. S/N 1975 AND BELOW  
WASHER, PULLEY ................................... 1 ................. S/N D1976 AND ABOVE  
BOLT 12 X 30 T  
99  
1
1
4
2
100  
101  
102  
103  
104  
SW M12  
ECCENTRIC ROTOR  
SOCKET HEAD BOLT 12 X 25 T  
SOCKET HEAD BOLT 12 X 40 T  
SHIM 70 X 90 X 0.5  
2
AS REQUIRED  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — CONTROL ( A-TYPE ) ASSY.  
CONTROL ( A-TYPE ) ASSY.  
PAGE 38 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — CONTROL ( A-TYPE ) ASSY.  
CONTROL ( A-TYPE ) ASSY.  
NO  
1
2
3
4
5
6
7
8
PART NO  
PART NAME  
QTY.  
2
4
4
4
1
1
2
6
1
1
1
1
1
1
1
1
2
2
2
2
2
4
4
4
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
4
4
4
REMARKS  
456329060  
001221235  
030212300  
031112230  
456111340  
001221676  
031116260  
032116280  
020316130  
023041600  
455434950  
455010030  
939010060  
020410060  
020412070  
022411635  
954404230  
001220620  
030206150  
031106100  
020306050  
001220820  
030208200  
031108160  
501402870  
501402880  
959403460  
020410060  
456211280  
455010040  
455329500  
456111180  
456442320  
456442150  
001221252  
020312100  
020412070  
031112230  
030212300  
001220830  
030208200  
031108160  
HANDLE BRACKET  
BOLT 12X35 T  
SW M12  
PW M12  
HANDLE  
BOLT 16X180 T  
PW M16  
CONICAL SPRING WASHER M16  
NUT M16  
NUT M16, H=10  
SPINDLE  
KNOB  
SHOCK ABSORBER 60  
NUT M10, H=6  
NUT M12, H=7  
WING NUT M16  
CLAMP SA120-18  
BOLT 6X20 T  
SW M6  
PW M6  
NUT M6  
BOLT 8X20 T  
SW M8  
PW M8  
HANDLE STOPPER/MDR  
SPRING/HANDLE, 1.4X18 X44  
BALL GRIP 32D-M10  
NUT M10, H=6  
HANDLE GRIP  
OIL HOSE 950L  
OIL HOSE 1180L  
LEVER, TRAVEL  
COLLAR 12X15. 6X32L  
RETURN SPRING, LEVER  
BOLT 12X60 T  
NUT M12  
9
10  
11  
12  
13  
14  
15  
16  
17  
18  
19  
20  
21  
22  
23  
24  
26  
27  
28  
29  
30  
33  
34  
36  
37  
38  
39  
40  
41  
42  
43  
44  
45  
46  
NUT M12, H=7  
PW M12  
PW M12  
BOLT 8X30 T  
SW M8  
PW M8  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — PUMP ( A-TYPE ) ASSY.  
PUMP
PAGE 40 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA — PUMP ( A-TYPE ) ASSY.  
PUMP ( A-TYPE ) ASSY.  
NO  
A
PART NO  
PART NAME  
QTY.  
REMARKS  
456910020  
456910030  
456910040  
456111150  
456328870  
456442310  
456329000  
456441750  
455437130  
080200240  
455326790  
040006004  
050200200  
455010120  
050100650  
001520615  
456211220  
456441520  
456441490  
456441590  
PUMP ASSY. ......................................... 1 .................... INCLUDES ITEMS W/  
SPOOL ASSY. ........................................ 1.................... INCLUDES ITEMS W/ $  
BLED VALVE ASSY................................. 1.................... INCLUDES ITEMS W/ #  
BODY  
SPOOL  
SPRING 1.0-5.1-35L  
SHAFT  
PINION  
WOODRUFF KEY  
STOP RING S-24  
COVER, PINION  
BEARING 6004  
*
B
*
C
*
1
1
1
1
1
1
2
1
1
2
1
1
1
8
1
1
1
1
2
1
1
1
2
2
1
1
2
2
1
1
4
1
2
1
4
4
*
2$  
*
3$  
5
*
*
6
7
*
*
8
9
*
*
10  
*
11  
12  
13  
14  
15  
16  
17  
O-RING 9-20  
DUST SEAL SER-20  
O-RING G-65  
*
*
*
*
*
*
*
SOCKET HEAD BOLT 6X15 T  
RESERVE TANK  
COVER, RESERVE TANK  
PACKING, RESERVE TANK  
BLED VALVE  
STEEL BALL 6.35D  
SPRING 0.9-5. 1-35L  
SOCKET HEAD SCREW 8X16 T  
NUT M8, H=5  
18#  
*
19 #$ 456441530  
*
20#  
21#  
456441550  
096208016  
*
*
22 #$ 020408050  
*
22 #$ 020408050  
23  
NUT M8, H=5  
*
456441650  
SET SCREW PT 1/8  
SET BOLT, SPOOL  
O-RING P-9  
*
23-1 $ 456443080  
*
24  
25  
26  
27  
28  
29  
30  
050200090  
050100450  
456010020  
953405270  
953400160  
506010160  
456328850  
*
*
*
*
*
*
*
O-RING G-45  
PACKING SKY-25  
PLUG 1/4X14 13L  
PACKING 1/4  
SOCKET HEAD PLUG 1/8  
CYLINDER COVER, F  
BALL SEAT  
PACKING 1/4, CU  
SOCKET HEAD BOLT 6X100 T  
SOCKET HEAD BOLT 6X15 T  
31 #$ 456441740  
*
32  
33  
34  
953405260  
001520660  
001520615  
*
*
*
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA —THROTTLE LEVER ( A-TYPE ) ASSY.  
THROTTLE ( A-TYPE ) ASSY.  
PAGE 42 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
MVH-200DA —THROTTLE LEVER ( A-TYPE ) ASSY.  
THROTTLE ( A-TYPE ) ASSY.  
NO  
1
2
2
3
4
5
6
7
PART NO  
PART NAME  
THROTTLE LEVER ASSY. 103F/SX  
SCREW 8 X 16  
SCREW 8 X 25  
WASHER, LOCK 8MM  
NUT M8 ..................................................... 2 ................. REPLACES 020308060  
SPACER 7 X 9.5 X15  
LEVER BRACKET, T ................................. 1 ................. REPLACES 456329370  
GROMMET MG-22D  
TUBE8-13-1300L  
LEVER STOPPER 462COS  
LEVER SPACE 515D04  
LEVER COVER  
QTY.  
REMARKS  
956200010  
092008016  
092008025  
030208200  
020108060  
455435000  
456331120  
959404390  
959021621  
456443060  
456443070  
456330100  
959405280  
506010070  
952010030  
455334250  
956100038  
359406810  
091004006  
1
2
2
2
1
1
1
1
1
1
1
2
9
12  
13  
14  
15  
16  
20  
21  
22  
23  
24  
BOOT  
CLAMPTC-150  
WAVE WASHERW-20 ............................... 3 ................. S/N C1834 AND ABOVE  
WIRE GUIDE, AL103F .............................. 1 ................. S/N C1834 AND ABOVE  
THROTTLEWIRE 1550-1740  
WIRE STOPPER AY (3D)  
SCREW 4 X 6  
1
1
1
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 43  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— CYLINDER BLOCK ASSY.  
CYLINDER BLOCK ASSY.  
1
2
NOTES:  
- SEE CYLINDER HEAD AND BONNET ASSY., ITEM1  
- SEE FUEL INJECTION PUMP ASSY., ITEM1  
1
2
PAGE 44 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— CYLINDER BLOCK ASSY.  
CYLINDER BLOCK ASSY.  
NO.  
2
PART NO.  
PART NAME  
QTY.  
REMARKS  
71487401560  
11435001700  
26106100122  
11435001200  
11435001210  
11435001220  
10522501240  
11435001250  
11487101330  
11435001380  
11435001412  
11436001454  
11435002100  
10542501690  
11469901760  
11429901950  
11425001800  
11425001830  
11425001841  
11425035150  
11427001600  
23876010000  
26106080352  
26226060182  
26226060222  
26366060002  
22190160002  
11429902030  
11435002113  
16011002220  
16011002220  
24162152112  
26106080122  
22312040080  
11435002200  
11435002210  
BLOCK ASSY, CYLINDER ..................................1 ............. INCLUDES ITEMS W/ #  
8#  
9#  
10  
11  
12  
13  
14  
16  
22  
23  
24  
27  
29  
30  
COVER, STARTER  
BOLT M10X 12 PLATED  
STUD, CYL. HEAD  
STUD, CYL. HEAD  
NUT 9  
WASHER  
NUT 9  
GASKET, CYL. HEAD CMP  
O-RING  
GASKET, CRANK CASE  
COVER (D), CRANK CASE  
BEARING, MAIN  
PLUG M16  
CAP, W/LUB. OIL GAUGE ...................................2 ............. INCLUDES ITEM W/  
O-RING  
SHIM SET  
COVER, INSPEC.WINDOW  
GASKET  
PIPE, L.O. INLET  
PARALLEL PIN 8X12  
PLUG PT 1/8, SCREW  
BOLT M 8X35 PLATED  
STUD M 6X18 PLATED  
STUD M 6X22 PLATED  
NUT M 6  
SEAL WASHER 16S  
RETAINER  
BALL BEARING  
SEAL, OIL  
1
2
2
2
2
4
2
1
1
1
1
1
2
*
32  
33  
2
1
1
1
1
2
1
15  
1
2
3
2
1
1
1
1
1
1
2
*
42  
43  
44  
45  
46  
47  
48  
49  
50  
51  
52  
53  
54  
55  
56  
57  
58  
59  
60  
SEAL, OIL  
NEEDLE BEARING  
BOLT M 8X12 PLATED  
PIN 4X8, STRAIGHT  
MAIN BEARING US=0.25 ...................................1 ............. UNDER-SIZED PART  
MAIN BEARING US=0.50 ...................................1 ............. UNDER-SIZED PART  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— CYLINDER HEAD & BONNET ASSY.  
CYLINDER HEAD & BONNET ASSY.  
PAGE 46 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— CYLINDER HEAD & BONNET ASSY.  
CYLINDER HEAD & BONNET ASSY.  
NO.  
1
6
7
8
9
10  
12  
PART NO.  
PART NAME  
QTY.  
REMARKS  
11487111020  
11487111100  
11487111110  
11435011120  
10115811180  
27310060001  
11477111250  
11477111260  
11477111650  
CYLINDER HEAD  
VALVE, SUCTION  
VALVE, EXHAUST  
SPRING, VALVE  
RETAINER, SPRING  
COTTER ASSY  
1
1
1
2
2
2
SUPPORT CAM ARM .........................................1 ............. INCLUDES ITEMS W/  
SUPPORT, ROCKER ARM  
ARM ASSY, INTAKE ...........................................1 ............. INCLUDES ITEMS W/ +  
SCREW, VALVE ADJUST.  
LOCK NUT 6  
ARM ASSY, EXHAUST ......................................1 ............. INCLUDES ITEMS W/ #  
SCREW, VALVE ADJUST.  
LOCK NUT 6  
CIRCLIP 12  
SEAL, VALVE STEM  
CAP, VALVE  
*
13  
1
*
14  
*
16 + 11425011240  
1
1
*
17 + 26856060002  
*
18  
11477111660  
*
20 # 11425011240  
1
1
2
2
2
1
1
2
1
1
2
2
2
1
*
21 # 26856060002  
*
22  
23  
24  
25  
26  
27  
28  
29  
30  
31  
32  
33  
34  
22242000120  
11435011340  
10501011490  
11477111461  
11477111470  
11425011600  
11425011901  
22351040008  
26106060452  
26226060552  
26366060002  
11477111310  
11477111950  
11425003591  
11425003640  
22312030160  
26106060552  
*
GASKET, NOZZLE  
SPACER, NOZZLE  
WASHER  
RETAINER  
SPRING PIN 4X8  
BOLT M 6X45 PLATED  
STUD M6X 55 PLATED  
NUT M 6  
GASKET, BONNET  
BONNET ASSY, HEAD .......................................1 ............. INCLUDES ITEMS W/ %  
SHAFT ASSY, DECOMP  
SPRING  
PARALLEL PIN 3X16  
BOLT M 6X55 PLATED  
36%  
39%  
41%  
44  
1
1
1
3
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— AIR CLEANER & MUFFLER ASSY.  
AIR CLEANER & MUFFLER ASSY.  
PAGE 48 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— AIR CLEANER & MUFFLER ASSY.  
AIR CLEANER & MUFFLER ASSY.  
NO.  
1
2
3#  
4#  
5#  
6
7#  
10  
11  
12  
13  
14  
15  
16  
17  
18  
21  
22  
23  
24  
PART NO.  
PART NAME  
QTY.  
REMARKS  
11425012211  
11428812511  
11465007450  
11428812520  
11428812531  
11425212560  
11465012591  
11425212550  
11425012300  
11439912010  
11435012202  
26106060252  
26226060142  
26226060552  
11425013201  
11438813600  
26106060122  
26216080182  
26306080002  
11428813800  
26554060182  
26367060002  
GASKET, AIR CLEANER  
1
CLEANER, AIR ...................................................1 ............. INCLUDES ITEMS W/ #  
LABEL, AIR CLEANER  
COVER COMPL.  
CASE, AIR CLEANER  
WASHER M 8, SEAL  
ELEMENT ASSY  
1
1
1
1
1
1
3
1
1
2
1
2
1
1
2
2
2
WING-NUT, M 8  
U-NUT  
PIPE, AIR INTAKE  
GASKET, AIR INTAKE  
BOLT M 6X25 PLATED  
STUD M 6X14 PLATED  
STUD M6X 55 PLATED  
GASKET (NON-ASB.)  
EXHAUST, MUFFLER  
BOLT M 6X12 PLATED  
STUD M 8X18 PLATED  
NUT  
DEFLECTOR EXH ...............................................1 ............. INCLUDES ITEMS W/  
SCREW M 6X18  
U-NUT M6  
*
25  
26  
*
1
1
*
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— CRANKSHAFT, PISTON & CAMSHAFT ASSY.  
CRANKSHAFT, PISTON & CAMSHAFT ASSY.  
1
2
NOTES:  
1
- SEE CYLINDER BLOCK ASSY., ITEM 24  
2
- SEE CYLINDER BLOCK ASSY., ITEM 56  
PAGE 50 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— CRANKSHAFT, PISTON & CAMSHAFT ASSY.  
CRANKSHAFT, PISTON & CAMSHAFT ASSY.  
NO.  
1
PART NO.  
PART NAME  
CAMSHAFT (D) ASSY  
TAPPET  
QTY.  
REMARKS  
71488014580  
11425014200  
11477114260  
11435014451  
71487321730  
10385401221  
11425021550  
11439921420  
22512040120  
71487222721  
71487022502  
11439922300  
22252000210  
71438G23700  
11820023200  
11438023100  
71438023600  
71487028511  
24101062024  
71487222040  
71487022542  
11487222050  
71487022552  
71438023610  
71438023620  
16031014550  
22512070360  
26106080202  
1
2
1
2
1
1
1
1
1
5
6
7
TAPPET, F.O.  
ROD, PUSH  
9
CRANKSHAFT ASSY  
NUT M16  
WASHER, FLYWHEEL  
FLYWHEEL  
17  
18  
19  
20  
22  
KEY 4X 12  
PISTON W/RINGS ...............................................1 ............. INCLUDES ITEM W/ *  
25  
31  
RING SET, PISTON  
PISTON PIN  
CIRCLIP 21  
1
1
2
*
32  
33  
36#  
37#  
38#  
40  
44  
46  
49  
54  
57  
61  
63  
65  
66  
67  
ROD ASSY, CONNECTING.................................1 ............. INCLUDES ITEMS W/ #  
BOLT, ROD  
PISTON PIN  
2
1
1
1
2
BEARING, CRANK PIN  
SHAFT ASSY, BALANCER  
BALL BEARING  
PISTON W/RING, 0.25OS ...................................1 .......... OVER-SIZE(O.S=0.25)PART  
RING SET O.S=0.25 ...........................................1 .......... OVER-SIZE(O.S=0.25)PART  
PISTON W/RING, 0.50OS ...................................1 .......... OVER-SIZE(O.S=0.50)PART  
RING SET O.S=0.50 ...........................................1 .......... OVER-SIZE(O.S=0.50)PART  
BEARING, PIN(U.S=0.25) ...................................1 .......... UNDER-SIZE(U.S=0.25)PART  
BEARING, PIN(U.S=0.50) ...................................1 .......... UNDER-SIZE(U.S=0.50)PART  
WASHER  
KEY 7X 36  
BOLT M 8X 20 PLATED  
1
1
1
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— LUB. OIL PUMP & GOV. ASSY.  
LUB. OIL PUMP & GOVERNOR ASSY.  
1
2
3
NOTES:  
1
- SEE CYLINDER BLOCK ASSY., ITEM 24  
- SEE CYLINDER BLOCK ASSY., ITEM 1  
- SEE CYLINDER BLOCK ASSY., ITEM 2  
2
3
PAGE 52 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— LUB. OIL PUMP & GOV. ASSY.  
LUB.OIL PUMP & GOVERNOR ASSY.  
NO.  
1
7
8
9
10  
11  
PART NO.  
PART NAME  
QTY.  
REMARKS  
11425032010  
11425032070  
10333832570  
22312030160  
26476060142  
11425035110  
11425035070  
24341000224  
26106060162  
11435061190  
22322030200  
11477061190  
71477061100  
11477061520  
11477061600  
11477061610  
11425266051  
18336066110  
11425266252  
11425066440  
10522566990  
26106060202  
26476060142  
26757060002  
11481861700  
11477161810  
11477161830  
11477161940  
11481866600  
11477166690  
11487066010  
11425066200  
13521061090  
22451060000  
11477161890  
11477161960  
24311000180  
PUMP ASSY, LUB. OIL  
COVER, LUB. OIL PUMP  
O-RING  
1
1
1
1
3
PARALLEL PIN 3X16  
BOLT M 6X 14, TAPPING  
STRAINER, LUB. OIL..........................................1 ............. INCLUDES ITEMS W/  
*
12  
FILTER, LUB. OIL  
O-RING 1A S-22.4  
BOLT M 6X 16 PLATED  
LEVER, GOVERNOR  
TAPER PIN 3X20  
WASHER  
GOVERNOR ASSY  
BEARING, NEEDLE  
SEAL, OIL  
WASHER,THRUST  
HANDLE, REGULATOR  
BRACKET, REGULATOR  
SPRING, RETURN  
BOLT, ADJUSTING  
SCREW  
BOLT M 6X 20 PLATED  
BOLT M 6X 14, TAPPING  
NUT, 6  
1
1
1
1
1
1
1
2
1
1
1
1
1
1
1
1
1
1
*
13  
*
14  
15  
22  
23  
25  
33  
34  
35  
36  
38  
39  
40  
41  
42  
43  
44  
51  
52%  
53%  
54%  
55%  
56%  
57  
58  
59  
60  
61  
LIMITER ASSY, FUEL ........................................1 ............. INCLUDES ITEMS W/ %  
WASHER, PLAIN 14  
PLATE  
1
1
1
1
1
1
1
1
1
NUT  
LIMITER ASSY, FUEL  
NUT M14  
SPRING, REGULATOR  
SPRING, RETURN  
LEAD  
WIRE 0.6  
PROTECTOR CMP..............................................1 ............. INCLUDES ITEMS W/ #  
SPACER  
O-RING 1A P-18.0  
63#  
64#  
1
1
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 53  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— COOLING & STARTING DEVICE ASSY.  
COOLING & STARTING DEVICE ASSY.  
PAGE 54 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— COOLING & STARTING DEVICE ASSY.  
COOLING & STARTING DEVICE ASSY.  
NO.  
1
2
3
4
5
6
7
8
PART NO.  
PART NAME  
QTY.  
REMARKS  
11487045201  
11435045320  
11435045340  
18372055210  
26106060202  
11436045101  
11425045301  
11425045310  
11425045330  
11437045351  
11488076051  
11488076251  
11488076511  
11488076520  
11487076530  
11487076540  
11488076550  
11487076560  
11487076570  
11487076580  
11487076620  
11487076630  
11435076591  
26106060082  
26106060122  
11425076600  
11425076610  
16080278260  
COVER  
1
1
1
1
1
1
4
4
1
4
RUBBER SEAL  
COLLAR  
GROMMET  
BOLT M 6X 20 PLATED  
CASE, FAN(SILVER)(17)  
RUBBER, CUSHION  
COLLAR  
SEAL, FAN CASE  
BOLT, FAN CASE  
STARTER ASSY, RE-COIL .................................1 ............. INCLUDES ITEMS W/ #  
RECOIL STARTER(D) ASSY. ..............................1 ............. INCLUDES ITEMS W/ *  
CASE (D) W/ NO LABEL  
REEL, RECOIL  
9
10  
11  
12#  
13 #  
1
1
2
1
1
1
2
1
1
1
1
4
3
1
1
2
*
14 #  
*
15 #  
*
RATCHET  
16 #  
SPRING, SPIRAL  
GUIDE, RATCHET  
SPRING, FRICTION  
SPRING, RETURN  
SET SCREW  
KNOB, STARTER  
ROPE, STARTER  
PULLEY, STARTER  
BOLT M 6X 8 PLATED  
BOLT M 6X 12 PLATED  
PLUNGER  
*
17 #  
*
18 #  
*
19 #  
*
20 #  
*
22 #  
*
23 #  
*
24#  
25  
26  
27  
28  
29  
HOLDER, PLUNGER  
CLAMP  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 55  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— FUEL INJECTION PUMP ASSY.  
FUEL INJECTION PUMP ASSY.  
PAGE 56 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— FUEL INJECTION PUMP ASSY.  
FUEL INJECTION PUMP ASSY.  
NO.  
2
PART NO.  
PART NAME  
QTY.  
REMARKS  
71487551100  
10554651020  
11425051080  
11465051100  
11425051160  
11465051300  
10554651330  
11425051340  
12455051350  
11425051600  
11425051640  
11425051650  
22351020006  
22351030008  
71487553100  
11487153001  
11959353080  
11425053120  
11959353130  
11477553140  
11477553210  
11487553100  
11425053331  
11425053400  
11487159804  
PUMP ASSY, F. INJECT......................................1 ............. INCLUDES ITEMS W/ #  
3#  
4#  
6#  
GASKET  
PLATE  
BODY, F.I. PUMP  
SPRING  
1
1
1
1
1
1
1
2
1
1
1
2
1
1
1
1
1
1
1
2
14#  
16#  
20#  
21#  
22#  
23#  
24#  
25#  
26#  
27#  
29  
31  
35  
36  
38  
40  
42  
44  
48  
VALVE ASSY, DELIVERY  
SPRING, DELIV. VALVE  
HOLDER, F.I.P. DELIVERY  
GASKET, DELIVERY  
LEVER ASSY, CONTROL  
SEAT (A), SPRING  
SEAT (B), SPRING  
SPRING PIN 2X 6  
SPRING PIN 3X 8  
VALVE ASSY, F. INJECT  
NOZZLE ASSY  
NUT, NOZZLE CASE  
SPRING, NOZZLE  
RETAINER , SPRING  
SPACER, VALVE STOP  
PIN  
HOLDER ASSY ...................................................1 ............. INCLUDES ITEMS W/  
PIN, SPRING  
SHIM PACK  
PIPE, FUEL INJECTION  
*
1
1
1
*
49  
67  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 57  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— FUELTANK & FUEL LINE ASSY.  
FUEL TANK & FUEL LINE ASSY.  
1
2
NOTES:  
1
- SEE FUEL INJECTION PUMP ASSY., ITEM 28  
- SEE FUEL INJECTION PUMP ASSY., ITEM 1  
2
PAGE 58 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK— FUELTANK & FUEL LINE ASSY.  
FUEL TANK & FUEL LINE ASSY.  
NO.  
PART NO.  
PART NAME  
QTY.  
REMARKS  
1
71435055711  
11428855041  
11428855081  
11425055100  
11435055150  
11425055201  
10385455220  
23414080000  
10530055080  
11425055121  
11425055130  
11429955210  
11439955230  
11425055301  
24341000150  
11465055810  
22117080000  
26106080452  
26366060002  
26476060142  
11477059030  
11427059010  
11426859061  
12472259050  
11425059060  
TANK, FUEL (RED)(50) .......................................1 ............. INCLUDES ITEM W/  
CAP ASSY, FUEL TANK .....................................1 ............. INCLUDES ITEM W/  
*
>
3
5
6
*
>
VALVE  
1
1
1
4
2
1
1
FILTER, FUEL  
PIPE, GAUGE  
DAMPER, FUEL TANK  
CLAMP  
GASKET 8, ROUND  
PLUG, DRAIN  
FILTER, FUEL OIL ..............................................1 ............. INCLUDES ITEM W/ #  
GASKET  
STAY  
*
7
8
*
*
9
*
10  
11  
12  
*
*
13#  
14  
1
1
1
15  
16  
17+  
18  
19  
20  
21  
22  
23  
STAY (B)  
COCK ..................................................................1 ............. INCLUDES ITEM W/ +  
O-RING 1A S-15.0  
BOLT, LIFTING  
WASHER 8  
BOLT M 8X 45 PLATED  
NUT M 6  
BOLT M 6X 14, TAPPING  
PIPE ASSY, FUEL OIL .......................................1 ..............INCLUDES ITEM W/ %  
CLIP, HOSE  
PIPE, FUEL OIL  
CLAMP 9  
1
1
1
1
2
2
24%  
25%  
26  
2
1
2
1
27  
PIPE, FUEL RETURN  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 59  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK—TOOL, LABEL & GASKET SET ASSY.  
TOOL, LABEL & GASKET SET ASSY.  
PAGE 60 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
YANMAR L70EE-DVMK—TOOL, LABEL & GASKET SET ASSY.  
TOOL, LABEL & GASKET SET ASSY.  
NO.  
3
4
5
6
PART NO.  
PART NAME  
QTY.  
REMARKS  
11425007090  
11425007111  
11426807240  
11426107350  
11426807350  
11425092600  
16033092730  
28110100120  
28110140170  
28210000150  
11425092101  
11425092130  
26116060454  
26116080454  
26716060002  
26716080002  
11435092301  
11435092311  
11435092350  
71487192600  
11487101330  
11435001380  
11435001412  
11429901950  
11425001841  
22190160002  
11435011340  
11477111461  
11477111310  
11435012202  
11425012211  
11425013201  
10333832570  
LABEL, AIR COOLED  
LABEL, YANMAR  
LABEL, CAUTION  
LABEL  
1
1
1
1
1
1
1
1
1
1
7
LABEL, HOW TO START  
BAG, TOOL  
DRIVER, +  
WRENCH 10X12  
WRENCH 14X17  
FEEDER, OIL  
F.W. LOCKING HANDLE .....................................1 ............. OPTIONAL PART  
REMOVER, FLYWHEEL ......................................1 ............. INCLUDES PARTS W/ $  
BOLT M 6X 45 PLATED ......................................4 ............. OPTIONAL PART  
BOLT M 8X 45 PLATED ......................................3 ............. OPTIONAL PART  
NUT 6 ..................................................................8 ............. OPTIONAL PART  
NUT M 8 ..............................................................6 ............. OPTIONAL PART  
GUIDE, OIL SEAL ...............................................1 ............. OPTIONAL PART  
INSTALLINGTOOL ..............................................1 ............. OPTIONAL PART  
INSTALLINGTOOL ..............................................1 ............. OPTIONAL PART  
GASKET SET .....................................................1 ............. INCLUDES PARTS W/  
GASKET, CYL HEAD CMP  
O-RING  
GASKET, CRANK CASE  
O-RING  
GASKET  
SEAL WASHER 16S  
SEAL, VALVE STEM  
GASKET, NOZZLE  
GASKET, BONNET  
GASKET, AIR INTAKE  
GASKET, AIR CLEANER  
GASKET (NON-ASB.)  
O-RING  
11  
12  
13  
14  
15  
16  
17  
19$  
20$  
21$  
22$  
23  
24  
25  
27  
*
29  
1
1
1
2
1
2
2
1
1
1
1
1
1
*
35  
*
36  
*
37  
*
38  
*
39  
*
40  
*
42  
*
44  
*
45  
*
46  
*
47  
48  
*
*
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 61  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Effective: October 1, 2002  
TERMS AND CONDITIONS OF SALE — PARTS  
PAYMENTTERMS  
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell  
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal  
any), and with Multiquip part numbers Equipment Manufacturer accounts who use  
Terms of payment for parts are net 10 days.  
FREIGHTPOLICY  
clearlymarked.  
our products as integral parts of their own  
products.  
All parts orders will be shipped collect or  
prepaidwiththechargesaddedtotheinvoice.  
All shipments are F.O.B. point of origin.  
Multiquip’sresponsibilityceaseswhenasigned  
manifesthasbeenobtainedfromthecarrier,  
andanyclaimforshortageordamagemustbe  
settledbetweentheconsigneeandthecarrier.  
6. Thefollowingitemsarenotreturnable:  
SPECIALEXPEDITINGSERVICE  
a. Obsolete parts. (If an item is in the  
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice  
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,  
insuredparcelpostorincaseswhereMultiquip  
mustpersonallydeliverthepartstothecarrier.  
(such as gaskets, seals, “O” rings,  
b. Any parts with a limited shelf life  
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY  
MINIMUMORDER  
chasedmorethansixmonthspriorto  
thereturndate.  
Multiquip shall not be liable hereunder for  
damagesinexcessofthepurchasepriceofthe  
The minimum charge for orders from Mul-  
tiquipis$15.00net.Customerswillbeasked  
for instructions regarding handling of orders  
notmeetingthisrequirement.  
c. Anylineitemwithanextendeddealer item with respect to which damages are  
netpriceoflessthan$5.00.  
claimed, and in no event shall Multiquip be  
liable for loss of profit or good will or for any  
otherspecial,consequentialorincidentaldam-  
ages.  
d. Special order items.  
RETURNEDGOODSPOLICY  
e. Electricalcomponents.  
f. Paint,chemicals,andlubricants.  
g. Decalsandpaperproducts.  
h. Itemspurchasedinkits.  
Returnshipmentswillbeacceptedandcredit  
willbeallowed,subjecttothefollowingprovi-  
sions:  
LIMITATIONOFWARRANTIES  
Nowarranties,expressorimplied,aremade  
in connection with the sale of parts or trade  
accessoriesnorastoanyenginenotmanufac-  
tured by Multiquip. Such warranties made in  
connectionwiththesaleofnew,completeunits  
are made exclusively by a statement of war-  
rantypackagedwithsuchunits,andMultiquip  
neitherassumesnorauthorizesanypersonto  
assume for it any other obligation or liability  
whatever in connection with the sale of its  
products.Apartfromsuchwrittenstatementof  
warranty, there are no warranties, express,  
impliedorstatutory,whichextendbeyondthe  
descriptionoftheproductsonthefacehereof.  
1. AReturnedMaterialAuthorizationmust  
be approved by Multiquip prior to ship-  
ment.  
7. Thesenderwillbenotifiedofanymaterial  
receivedthatisnotacceptable.  
2. ToobtainaReturnMaterialAuthorization,  
alistmustbeprovidedtoMultiquipParts  
Salesthatdefinesitemnumbers,quanti-  
ties, and descriptions of the items to be  
returned.  
8. Suchmaterialwillbeheldforfiveworking  
days from notification, pending instruc-  
tions.Ifareplyisnotreceivedwithinfive  
days,thematerialwillbereturnedtothe  
senderathisexpense.  
a. Thepartsnumbersanddescriptions  
must match the current parts price  
list.  
9. Creditonreturnedpartswillbeissuedat  
dealer net price at time of the original  
purchase,lessa15%restockingcharge.  
b. The list must be typed or computer  
generated.  
10. In cases where an item is accepted, for  
which the original purchase document  
can not be determined, the price will be  
basedonthelistpricethatwaseffective  
twelvemonthspriortotheRMAdate.  
c. The list must state the reason(s) for  
thereturn.  
d. The list must reference the sales  
order(s)orinvoice(s)underwhichthe  
itemswereoriginallypurchased.  
11. Credit issued will be applied to future  
purchasesonly.  
e. The list must include the name and  
phonenumberofthepersonrequest-  
ingtheRMA.  
PRICINGANDREBATES  
Prices are subject to change without prior  
notice.Pricechangesareeffectiveonaspe-  
cificdateandallordersreceivedonorafterthat  
datewillbebilledattherevisedprice.Rebates  
3. AcopyoftheReturnMaterialAuthoriza-  
tionmustaccompanythereturnshipment.  
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice  
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand  
Multiquip’sdesignatedreceivingpoint.  
atthetimeofanypricechange.  
PAGE 62 — MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05)  
Download from Www.Somanuals.com. All Manuals Search And Download.  
NOTE PAGE  
MVH-200DA PLATE COMPACTOR — OPERATION & PARTS MANUAL — REV. #0 (03/21/05) — PAGE 63  
Download from Www.Somanuals.com. All Manuals Search And Download.  
OPERATION & PARTS MANUAL  
HERE'S HOW TO GET HELP  
PLEASE HAVETHE MODEL AND SERIAL  
NUMBER ON-HANDWHEN CALLING  
MULTIQUIP CORPORATE OFFICE  
18910 Wilmington Ave.  
Carson, CA 90746  
800-421-1244  
FAX:310-537-3927  
Email: [email protected]  
Internet:www.multiquip.com  
PARTS DEPARTMENT  
800-427-1244  
310-537-3700  
FAX:800-672-7877  
FAX:310-637-3284  
MAYCO PARTS  
800-306-2926  
310-537-3700  
FAX:800-672-7877  
FAX:310-637-3284  
SERVICE DEPARTMENT  
800-421-1244  
FAX:310-537-4259  
310-537-3700  
TECHNICAL ASSISTANCE  
800-478-1244  
FAX:310-631-5032  
FAX:310-537-1173  
WARRANTYDEPARTMENT  
800-421-1244,EXT.279  
310-537-3700,EXT.279  
Your Local Dealer is:  
MULTIQUIP INC.  
18910WILMINGTONAVE.  
CARSON, CALIFORNIA 90746  
800-421-1244 • 310-537-3700  
FAX:310-537-3927  
E-mail:[email protected]  
Internet:multiquip.com  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Cooktop KM5732 User Manual
Milwaukee Flat Panel Television 6480 20 User Manual
MTX Audio Speaker T8104A User Manual
Multiquip Portable Generator M2870300504 User Manual
Network Technologies Network Card ST NXM U HD User Manual
Nikon Camera Lens MH 52 User Manual
Oki Camcorder Hard Disk Drive User Manual
Panasonic Air Conditioner CS E24FKR User Manual
Panasonic Laptop CF Y4 User Manual
Patton electronic Marine Battery 2017P60 RS 232 to 60mA User Manual