OperatiOn and parts Manual
MOdel tp24
tile saw
(electric MOtOr)
Revision #2 (04/12/12)
To find the latest revision of this
publication, visit our website at:
THIS MANUAL MUST ACCOMPANY THE EQUIPMENT AT ALL TIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
silicOsis/respiratOry warnings
WARNING WARNING
SILICOSIS WARNING
RESPIRATORY HAZARDS
Grinding/cutting/drilling of masonry, concrete, metal and
other materials with silica in their composition may give
off dust or mists containing crystalline silica. Silica is a
basic component of sand, quartz, brick clay, granite and
numerous other minerals and rocks. Repeated and/or
substantial inhalation of airborne crystalline silica can
cause serious or fatal respiratory diseases, including
silicosis. In addition, California and some other
authorities have listed respirable crystalline silica as a
substance known to cause cancer. When cutting such
materials, always follow the respiratory precautions
mentioned above.
Grinding/cutting/drilling of masonry, concrete, metal and
other materials can generate dust, mists and fumes
containing chemicals known to cause serious or fatal
injury or illness, such as respiratory disease, cancer,
birth defects or other reproductive harm. If you are
unfamiliar with the risks associated with the particular
process and/or material being cut or the composition of
the tool being used, review the material safety data
sheet and/or consult your employer, the material
manufacturer/supplier, governmental agencies such as
OSHA and NIOSH and other sources on hazardous
materials. California and some other authorities, for
instance, have published lists of substances known to
cause cancer, reproductive toxicity, or other harmful
effects.
Control dust, mist and fumes at the source where
possible. In this regard use good work practices and
follow the recommendations of the manufacturers or
suppliers, OSHA/NIOSH, and occupational and trade
associations. Water should be used for dust
suppression when wet cutting is feasible. When the
hazards from inhalation of dust, mists and fumes cannot
be eliminated, the operator and any bystanders should
always wear a respirator approved by NIOSH/MSHA for
the materials being used.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
table Of cOntents
tp24 tile saw
Proposition 65 Warning ........................................... 2
Silicosis/Respiratory Warnings................................ 3
Table Of Contents.................................................... 4
Parts Ordering Procedures...................................... 5
Safety Information ................................................ 6-9
Specifications ........................................................ 10
Dimensions............................................................ 11
General Information............................................... 12
Saw Components ............................................. 14-15
Electric Motor Components................................... 16
Set-Up .............................................................. 16-20
Sawing Guides ................................................. 20-21
Operation.......................................................... 22-23
Maintenance..................................................... 24-30
Wiring Diagram (Electric Motor) ............................ 31
Troubleshooting (Blade)......................................... 32
Troubleshooting (Saw)........................................... 33
Explanation Of Code In Remarks Column............. 34
Suggested Spare Parts ......................................... 35
Main Saw Assembly ......................................... 36-37
Cutting Head Assembly.................................... 38-39
Electric Motor Assembly................................... 40-41
Cutting Table Assembly .................................... 42-43
Blade Guard Assembly..................................... 44-45
Bearing Housing Assembly .............................. 46-47
Switch Box Assembly ....................................... 48-49
Tools And Accessories ..................................... 50-51
Terms And Conditions Of Sale — Parts ................ 52
NOTICE
Specifications and part numbers are subject to change
without notice.
page 4 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
parts Ordering prOcedures
Ordering parts has never been easier!
choose from three easy options:
Effective:
January 1st, 2006
Best deal!
order via Internet (dealers only):
Order parts on-line using Multiquip’s SmartEquip website!
If you have an Mq Account, to obtain a Username
and Password, E-mail us at: parts@multiquip.
com.
I View Parts Diagrams
I Order Parts
I Print Specification Information
To obtain an Mq Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% discount
on Standard orders for all orders which include
complete part numbers.*
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 2% discount
on Standard orders for all orders which include
complete part numbers.*
order via Fax (dealers only):
All customers are welcome to order parts via Fax.
domestic (uS) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
domestic (uS) dealers Call:
order via phone:
1-800-427-1244
non-dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
when ordering parts, please supply:
Ì
dealer account number
Ì
Specify preferred method of Shipment:
Ì
Ì
Ì
Ì
Ì
dealer name and address
ꢀ UPS/Fed Ex
ꢀ DHL
ꢀ Truck
I
I
Priority One
Ground
Shipping address (if different than billing address)
return Fax number
I Next Day
Second/Third Day
applicable model number
I
Quantity, part number and description of each part
NOTICE
All orders are treated as Standard Orders and will
ship the same day if received prior to 3PM PST.
We aCCepT aLL maJor CredIT CardS!
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
Do not operate or service the equipment before reading
the entire manual. Safety precautions should be followed
at all times when operating this equipment.
Failure to read and understand the safety
messages and operating instructions could
result in injury to yourself and others.
Potential hazards associated with the operation of this
equipment will be referenced with hazard symbols which
may appear throughout this manual in conjunction with
safety messages.
Symbol
Safety Hazard
SaFeTy meSSageS
The four safety messages shown below will inform you
about potential hazards that could injure you or others.The
safety messages specifically address the level of exposure
to the operator and are preceded by one of four words:
danger, WarnIng, CauTIon or noTICe.
Rotating parts hazards
Cutting and crushing hazards
Electric shock hazards
SaFeTy SymBoLS
danger
Indicates a hazardous situation which, if not avoided,
WILL result in deaTH or SerIouS InJury.
WarnIng
Indicates a hazardous situation which, if not avoided,
CouLd result in deaTH or SerIouS InJury.
CauTIon
Indicates a hazardous situation which, if not avoided,
CouLd result in mInor or moderaTe InJury.
NOTICE
Addresses practices not related to personal injury.
page 6 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
generaL SaFeTy
NOTICE
CauTIon
„ This equipment should only be operated by trained and
qualified personnel 18 years of age and older.
„ never operate this equipment without proper protective
clothing, shatterproof glasses, respiratory protection,
hearing protection, steel-toed boots and other protective
devices required by the job or city and state regulations.
„ Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
„ Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
„ never use accessories or attachments that are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
„ Avoid wearing jewelry or loose fitting clothes that may
snag on the controls or moving parts as this can cause
serious injury.
„ aLWayS know the location of the nearest
fire extinguisher.
„ never operate this equipment when not
feeling well due to fatigue, illness or when
under medication.
„ aLWayS know the location of the nearest
first aid kit.
„ never operate this equipment under the
influence of drugs or alcohol.
„ aLWayS know the location of the nearest phone or keep
a phone on the job site. Also, know the phone numbers
of the nearest ambulance, doctor and fire department.
This information will be invaluable in the case of an
emergency.
„ aLWayS clear the work area of any debris, tools, etc.
that would constitute a hazard while the equipment is
in operation.
„ No one other than the operator is to be in the working
area when the equipment is in operation.
„ aLWayS check the equipment for loosened threads or
bolts before starting.
„ do noT use the equipment for any purpose other than
its intended purposes or applications.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
SaW SaFeTy
CauTIon
danger
„ never operate the saw without blade
guards and covers in place. Exposure of
the diamond blade must not exceed 180
degrees.
„ neveroperatetheequipmentinanexplosiveatmosphere
or near combustible materials. An explosion or fire could
result causing severe bodily harm or even death.
„ Verify the motor start switch is set to the OFF position
before installing a blade.
WarnIng
„ Accidental starting can cause severe injury
or death. aLWayS place the ON/OFF
switch in the OFF position.
„ aLWayS inspect blade before each
use. The blade should exhibit no cracks,
dings, or flaws in the steel centered core
and/or rim. Center (arbor) hole must be
undamaged and true.
„ Keep hands away from moving parts at all
times.
NOTICE
„ never disconnect any emergency
or safety devices. These devices are
intended for operator safety. Disconnection of these
devices can cause severe injury, bodily harm or even
death. Disconnection of any of these devices will void
all warranties.
„ Use proper blades and follow blade manufacturer’s
recommendations. Match the blade RPM (blade shaft
RPM) to the recommended blade surface feet per minute
(SFPM).
„ Ensure the blade-mounting bolt is tightened
adequately
CauTIon
„ aLWayS ensure saw is securely placed on appropriate
blocks or jackstands when maintenance requires
elevation of the saw.
„ aLWayS examine blade flanges for damage and
excessive wear.
„ Ensure the blade is marked with an operating speed
greater than the spindle speed of the saw.
„ If the machine malfunctions, stop the saw immediately
and secure it. Fix the problem as soon as possible.
„ Only cut the material that is specified for the diamond
blade. Read the specification of the diamond blade to
ensure the proper tool has been matched to the material
being cut.
NOTICE
„ aLWayS keep the machine in proper running condition.
„ Fix damage to machine and replace any broken parts
immediately.
„ If wet cutting, ensure a WeT CuTTIng blade is being
used and that the water supply system to the blade is
properly functioning and being used.
„ Make sure there is no buildup of grease, oil or debris
on the machine.
„ do noT drop the diamond blade on ground or
surface.
„ aLWayS store equipment properly when it is not being
used.Equipment should be stored in a clean, dry location
out of the reach of children and unauthorized personnel.
„ Ensure that the blade is mounted for proper operating
direction.
BLade SaFeTy
„ Adhere to the blade manufacturer’s recommendations
on handling, storage and safe usage of blades.
WarnIng
„ Rotating blade can cut and crush.aLWayS
keep hands and feet clear while operating
the saw.
page 8 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
safety infOrMatiOn
eLeCTrIC moTor SaFeTy
LIFTIng SaFeTy
NOTICE
CauTIon
„ Operate electric motor only at the specified voltage
indicated on the nameplate.
„ never allow any person or animal to stand underneath
the equipment while lifting.
„ do noT spray water onto electric motor.
„ Some saws are very heavy and awkward to move around.
Use proper heavy lifting procedures.
„ aLWayS disconnect AC power plug from power source
before moving saw, changing blade, or performing
maintenance.
„ do noT lift machine to unnecessary heights.
„ never lift the equipment while the motor is running.
TranSporTIng SaFeTy
„ aLWayS make sure the ON/OFF switch
on the electric motor is in the OFF position
when not in use and before inserting the
saw’s power plug into an AC receptacle.
NOTICE
„ aLWayS shutdown motor before transporting.
power Cord/Cable Safety
„ aLWayS tie down equipment during transport by
securing the equipment with rope.
danger
„ never let power cords or cables lay in water.
„ Ensurethatthediamondbladedoesnotcomeintocontact
with the ground or surface during transportation.
„ never use damaged or worn cables or cords when
connecting equipment to generator. Inspect for cuts in
the insulation.
„ never transport the saw to or from the job site with the
blade mounted.
„ never grab or touch a live power
cord or cable with wet hands. The
possibility exists of electrical shock,
electrocution or death.
envIronmenTaL SaFeTy
NOTICE
„ Dispose of hazardous waste properly.
Examples of potentially hazardous waste
are used motor oil, fuel and fuel filters.
„ Make sure power cables are securely
connected. Incorrect connections may
cause electrical shock and damage to the
saw.
„ do noT use food or plastic containers to dispose of
hazardous waste.
CauTIon
„ do noT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
„ Ensure that cables and cords will not be tripped over or
trapped underneath the saw.
„ Never use the cable to pull out the plug from the power
source.
NOTICE
„ aLWayS make certain that proper power or extension
cord has been selected for the job.
„ Protect the cable from heat, oil, and sharp edges.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
specificatiOns
Table 1. Saw Specifications
model
Blade Capacity
Blade rpm
TP24
10 in. (254 mm)
3200
arbor Size
5/8 in. (15.875 mm)
Cast Aluminum
Blade guard
Blade Shaft Bearings
Cutting Head
Water-Cooled
Cast Aluminum, Adjustable
Aluminum with roller bearings, injected
molded rubber pad, transportation lock
Conveyor Cart
drive System
max. depth of Cut
Straight Cut
diagonal Cut
Water Tray
V-belt
3-1/2 in. (90 mm)
24 in. (610 mm)
16 in. (406 mm) x 16 in. (406 mm) Size Tile
ABS
Water pump
Weight
115V, 60 Hz — 100 GPH
65 lbs. (29 kg)
Table 2. electric motor Specifications
Horsepower
volts
2
115
amps
15
motor rpm
Cycle
3000 RPM
60
1
phase
Class
E
page 10 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
diMensiOns
C
B
A
Figure 1. Dimensions
Table 3. dimension
reference Letter
dimensions
36.5 in. (927 mm)
26 in. (660 mm)
20.4 in. (518 mm)
A
B
C
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
general infOrMatiOn
The TP24 is a powerful, robust saw designed to
professionally handle large-sized cuts on ceramics, stone,
and masonry materials. A sturdy steel precision frame and
easily removable ABS water tray provides overall durability
and longevity.
aCCeSSorIeS/repLaCemenT parTS
If desired, theTP24 tile saw can be equipped with a support
stand with wheels.This stand is ideal when the saw needs
to be placed on a secure reliable platform.
FeaTureS
This saw is equipped with a trusted high-torque 2 HP
electric motor that operates on standard 115V power and is
designed with thermal overload and fan air cover protection.
„ rugged portable Frame assembly — Sturdy steel
frame design with handles for easy transport.
An innovative water-cooled bearing assembly works in
conjunction with the water pump to keep key bearing
components running cooler.
„ electric Induction motor — UL/CSA approved 115 V
60 Hz, 2 HP electric motor with thermal overload and
fan cover protection.
The TP24 saw comes complete with premium blade and
high flow water pump.
„ Water Tray — Sturdy ABS water tray that is easily
removable for cleaning.
dry CuTTIng appLICaTIonS
„ Cutting Table — Rugged cast aluminum table with
heavy-duty injected molded rubber padding and
extension table. Industrial ball bearing rollers ensure
smooth, precise cart movement.
TheTP24 tile saw is shipped from the factory for wet-cutting
saw applications, however it can be used for dry-cutting
saw applications.The most import thing to remember is to
disconnect the water pump. The water pump is cooled by
the flow of water, and failure to disconnect the pump (when
running dry) will cause pump failure.
„ Waterpump—Powerful, maintenance-free, submersible
pump provides high volume water flow.
„ Water-Cooled Blade Shaft Bearing assembly — High
flow water circulating system designed to keep crucial
bearing components running cooler.
NOTICE
never have the water pump engaged when dry cutting
applications are involved.
„ Blade guard — Hardy cast guard with blade brushes
designed to evenly distribute water to the blade, and to
easily position for blade changes.
BLade appLICaTIonS
This saw has been designed to incorporate the use
of diamond blades as the cutting tool. The optimum
performance of this saw is best evidenced by using 10-inch
(254 mm) diamond blades that match the material being
cut. Ask your dealer, or call Multiquip about your specific
cutting application.
„ diamond Blade — 10-inch (254 mm) premium tile blade
included.
page 12 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
nOtes
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
saw cOMpOnents
5
9
3
1
8
4
11
2
10
12
22
7
13
6
14
17
23
19
21
20
16
24
18
15
Figure 2. Saw Components
page 14 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
saw cOMpOnents
Figure 2 shows the location of the basic components of
the TP24 saw. Listed below is a brief explanation of each
component.
13. CuttingTable — Place material to be cut on this rubber
padded table. For ease of cutting, this table has been
placed on rails so that it can easily slide back and forth.
1. aCpowerCord—Plugthiscordintoa125VACreceptacle
when starting of the electric motor is required.
14. ruler Backstop — When cutting, place material
against backstop. Use measurement rail (ruler) to
determine where material is to be cut.
2. v-belt Cover — Remove this cover to access the drive
V-belt. never operate the saw with the V-belt cover
removed
15. Stopper — Place stopper in water tray when filling
with water.
3. rubber Splash guard — Keeps water from splashing
from the blade.
16. BearingHousing—Housespermanentlylubricatedball
bearings to allow motor shaft to rotate smoothly.
4. electric motor — This unit uses a 115V, 60 Hz, 2 HP
electric motor.
17. Cutting Head adjustment Knob — Turn knob
clockwise to loosen and position cutting head to desired
height. Turn counterclockwise to tighten.
5. overcurrent Breaker Button — When a thermal
overload condition exists, press this button to reset the
breaker. Allow time for the electric motor to cool down
before reseting the breaker.
18. Water Tray — When wet cutting is required, fill with
clean fresh water. Make sure submersible pump is
totally immersed in water.
6. Cutting Blade — This unit uses a 10-inch (254 mm)
premium diamond blade. Always use recommended
Multiquip cutting blades.When mounting of the cutting
blade is required, remove the spindle bolt and outside
blade flange.Align cutting blade with inside flange arbor
and reassemble spindle and outside blade flange.
19. electric Water pump — The electric water pump for
this saw requires 115 VAC. Plug power cord of electric
water pump into AC receptacle located on conduit
box. never run pump dry. Pump must be immersed
in water.
20. Water Lines — Replace the clear vinyl tubing water
lines when they become brittle, worn or clogged.Water
kits are available through your Multiquip dealer.
7. Cutting Head Handle — Grab hold of this handle to
control the movement of the cutting head.
8. power on/oFF Switch — To turn on the saw place
in the ON position. Place in the OFF position to shut
down the saw.
21. maintenanceWrench —Usethismulti-purposewrench
when performing maintenance or repairs on the saw.
22. rear dripTray — Rear drip tray increases the surface
area for collecting water and slurry to prevent spillage.
9. Water pump power receptacle — Plug the water
pump power cord into this AC receptacle.
23. masterguide Template Base — Mounts to ruler
backstop to ensures precision while making cuts.
10. Blade guard — Protects the user from the cutting
blade. never operate the saw with the blade guard
removed.
24. Water LInk Hose — Recycles water from the bearing
housing back into the water tray.
11. Blade guard adjustment Knob — Turn knob
clockwise to loosen and remove blade guard. Turn
counterclockwise to tighten.
12. Blade guard Brushes — Prevents foreign matter and
debris from accumulating on the saw blade. Replace
brushes immediately when they become worn or
damaged.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
electric MOtOr cOMpOnents/set-up
3. Slide water pump onto U-shaped bracket located at
the bottom of the frame. See Figure 6.
eLeCTrIC moTor ComponenTS
Figure 3 shows the location of the components of the
electric motor.
115 VAC, 60 Hz
SINGLE -PHASE
ELECTRIC MOTOR
4. Slide cutting head onto the post. Secure cutting head
to the shaft using provided flat washer, lock washer and
nut. Attach cutting depth control knob and washer to
the cutting head through the slot located underneath
the belt guard. See Figure 4.
5. Mount blade guard onto shaft protruding from the side
of the cutting head. Secure the blade guard in place
using the provided serrated washer and blade guard
knob.
OVERCURRENT
BREAKER BUTTON
6. Attach rear drip tray to the water tray.
BLADE
GUARD
KNOB
REAR
DRIP
TRAY
BLADE
GUARD
CUTTING
HEAD
ELECTRIC
MOTOR
ON/OFF SWITCH
ELECTRIC WATER
PUMP AC
RECEPTACLE
Figure 3. Electric Motor Components
CUTTING
DEPTH
CONTROL
KNOB
SaW SeT-up
WATER
TRAY
WarnIng
Whenever cleaning, adjusting or lubricating any part
of the saw, make certain to place the power ON/OFF
switch in the oFF position and disconnect the plug from
the power source.
SHAFT
Figure 4. Saw Assembly
7. If using the optional support stand, assemble as
described in the Support Stand Assembly section.
Make sure that the saw is secured on the support
stand as instructed.
1. Open the shipping container carefully, lift the saw by
its carrying handles and place it on a suitable table or
platform. Make sure the table or platform can support
the weight of the saw.
2. Make sure that the following items are found in the
container:
SupporT STand aSSemBLy (opTIonaL)
Refer to Figure 5 for location of components.
1. Remove the folding stand from its box.
„ Saw
„ Water Pump
„ Rear Drip Tray
„ Owner’s Manual
„ Rip Guide
„ Water Tray
„ Drain Plug
„ Universal Wrench
„ Saw Blade
2. While holding the stand upright, spread both sets of
legs apart and swing the workbench over and on top
of the legs.
3. Seat the saw securely onto the stand.
page 16 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
set-up
8. Insert the water pump power plug into the outlet cable
receptacle from the electric motor conduit box as shown
in Figure 7.
ELECTRIC MOTOR
CONDUIT BOX
CONDUIT
BOX
CABLE
RECEPTACLE
POWER
PLUG
WATER
PUMP
Figure 7. Water Pump Power Connection
Figure 5. Support Stand Assembly
ConneCTIng THe WaTer pump
Refer to Figure 6.
WarnIng
Disconnect the pump before attempting to handle the
pump. never operate pump without water in the tray.
4. Attach the water hose coming from the blade guard
and bearing housing to the water pump.
NOTICE
5. Install drain plug in water tray.
The above procedure is for wet cutting applications only.
never dry cut with the pump connected to an AC power
source. Running the pump dry will damage the pump.
aLWaySdisconnectthepump’spowercordwhendrycutting.
6. Fill the water tray with clean fresh water. The water
pump intake must always be fully covered by water.
Also, keep the pump intake free of sludge, debris and
other materials that may accumulate in the tray.
7. Make certain that the water hose will not come in contact
with the blade or interfere with any moving parts.
BLADE
GUARD
WATER
WATER
PUMP
HOSES
DRAIN
PLUG
BEARING
HOUSING
Figure 6. Connecting the Water Pump
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
set-up
3. directional arrow — Check to ensure that the blade is
orientedproperlyonthespindleforsawing.Referencethe
directionalarrowonthebladeandplaceitsothedirection
of rotation “downcuts” with the turn of the shaft.
BLadeS
WarnIng
Failure to thoroughly inspect the blade for
operational safety could result in damage to
thebladesorthesawandmaycauseserious
injury to the user or others in the operating
area.Inspect the blade flanges and shaft for
damage before installing the blade.
4. diamond Segment or rim — Ensure that there are
no cracks, dings, or missing portions of the diamond
segment/rim. do noT use a blade that is missing
a segment or a portion of the rim. Damaged and/or
missing segments/rims may cause damage to your saw
and injury to the user or others in the operating area.
5. Specifications — Ensure that the blade specifications,
size, and diameter properly match up to the sawing
operation.Wetbladesmusthavewatertoactasacoolant.
Utilizingadiamondbladenotmatchedproperlytothetask
may result in poor performance and/or blade damage.
6. arbor Hole — It is essential that the arbor hole
diameter properly matches the shaft arbor, and that it
is free from distortions. Correct blade flanges (collars)
must be used. The inside face of the flanges must be
clean and free of debris.An out of round arbor condition
will cause damage to the blade and the saw.
Blade Components
Diamond blades are recommended for your saw. Ask your
Multiquip dealer about your specific cutting application.
Figure 8 highlights the components of a diamond blade.
2
1
3
4
7. maX rpm —This RPM reference is the maximum safe
operating speed for the blade selected.never exceed
themaxRPMonthediamondblade.ExceedingtheMAX
RPM is dangerous, and may cause poor performance
and may damage the blade. All blades used must be
designed for the maximum spindle RPM.
SPECIFICATIONS
MAX. RPM
5
7
Cutting depth
The recommended cutting depth is 1/4" (6 mm) below the
cutting table surface.To adjust the cutting depth, loosen the
cutting head adjustment knob so that the blade is 1/4" below
the top of the cutting table's surface.SeeTable 4 to determine
cutting depth by blade diameter.
6
Figure 8. Diamond Blade
1. Stress relief Holes (gullets) — Check the steel core
for cracks that may have propagated from the slots
and/or gullets. Cracks indicate extreme fatigue failure
and if sawing continues, catastrophic failure will occur.
WarnIng
Setting the blade too low may damage the cutting table
and if set too high, the blade may grab the material
being cut, causing damage and possibly injury.
2. edge of the Steel Core — Check the diameter edge for
discoloration (blue oxidation) indicating an overheating
condition caused by insufficient cooling water/air.
Overheating of blades may lead to loss of core tension
and/or increase the possibility for blade failure. Check
to make sure the steel core’s width is uniform about
the rim of the blade, and not succumbing to an “under
cutting” condition brought about by highly abrasive
material or improper under cutting core protection.
Table 4. Blade diameter vs. Cutting depth
Blade diameter
7 in. (178 mm)
10 in. (254 mm)
Cutting depth
1-3/4 in. (44.5 mm)
3-1/2" (90 mm)
page 18 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
set-up
5. Loosen blade guard adjustment knob, lower the blade
guard, and retighten the knob.
Blade Installation
Refer to Figure 9 and the following instructions for installing
the blade.
6. Slightly loosen the cutting head adjustment knob, lower
the cutting head so that the blade is 1/4" (6 mm) below
the surface of the cutting table.Tighten the adjustment
knob firmly to hold the cutting head in place.
1. Loosen blade guard adjustment knob located at the
rear of the blade guard. Carefully raise the cutting
head to its highest position and secure it into place by
tightening the blade guard adjustment knob.
BLADE
BLADE
SHAFT
NUT
GUARD
ADJUSTMENT
KNOB
BLADE
2. Remove the blade shaft nut and outer flange.If a blade
has been mounted, hold the blade with one hand and
use the other hand to loosen the nut with the universal
wrench. Remove existing blade.
OUTER
FLANGE
3. Mount new blade, but make certain the arrow on the
blade coincides with the rotation direction of the shaft.
Ensure the capacity of the blade guard matches the
diameter of your cutting blade.
INNER
FLANGE
BLADE
GUARD
BLADE
SHAFT
4. Attach outer flange and blade shaft nut.Hold the blade
with one hand and use the other hand to tighten the
nut with the universal wrench.Make certain the flanges
are pressed flush against the blade and that the nut is
firmly tighthened, but do noT over tighten.
Figure 9. Blade Installation
See Table 5 for proper blade use guidelines.
Table 5. proper Blade use
dos
don’ts
Inspect blades daily for cracks or uneven wear.
Do not operate the saw without safety guards in place.
Do not operate the saw with blades larger than 10
in. (254 mm)
Always use appropriate blades for material being cut.
Inspect arbor shaft for uneven wear before mounting
blade.
Do not cut dry with blades marked “Use Wet”.
Do not exceed manufacturer’s recommended
maximum RPM.
Always use blades with the correct arbor shaft size.
Ensure that blade is mounted in the correct
direction.
Do not force blade into material. Let blade cut at its
own speed.
Do not make long cuts with dry blades. Allow them
to air cool.
Use proper safety equipment when operating the saw.
Always have a continuous flow of water on both
sides of blade.
Do not use the edge or side of blade to cut or grind.
Do not attempt to cut a radius or curve.
Secure the blade to the arbor with a wrench.
Inspect segment blades for segment cracking or loss. Do not cut too deep or too fast into the material.
Do not cut any material not recommended by blade
Do not use damaged blades.
manufacturer.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
set-up/sawing guides
4. Plug the free end of the extension cord into an AC power
receptacle. Whenever possible use a GFCI receptacle
(Figure 11) to reduce the risk of electrical shock.
ConneCTIng THe poWer
1. Place the power ON/OFF switch (Figure 10) in the OFF
position (down).
2. Connect an extension cord of adequate current carrying
capacity to the power plug on the electric motor.
3. maKe CerTaIn that the correct size extension cord
is used. Undersized wires will burn out motors. Use
Table 6 to determine the correct extension cord size.
Table 6. extension Cord Sizes
25 ft
(7.6 m) (15. 2 m) (22.9 m)
50 ft
75 ft
voltage
vaC
motor
Figure 11. GFCI Receptacle
Long
Long
Long
SaWIng guIdeS
2 HP
115
No. 12
No. 10
No. 8
using the CuttingTable
„ The ruler guide has inches marked along the top to allow
convenient measurements and to promote precision cuts.
See Figure 12.
„ The table spans an area of 16" x 16" (406 x 406 mm).
With the optional side extension table equipped, the cast
aluminum cutting table spans an area of 25" x 16" (635
x 406 mm), which allows it to provide greater support
for handling larger materials.
ELECTRIC
ELECTRIC
MOTOR
ON/OFF SWITCH
MOTOR
POWER
PLUG
CONNECT TO
115/230 VAC
POWER SOURCE
„ Cutting table is covered by a rubber mat that provides a
firm, durable work surface.
EXTENSION
CORD
„ A rip guide should be used with the cutting table to ensure
precision while making cuts.
Figure 10. Extension Cord Connection
SIDE EXTENSION
TABLE (OPTION)
danger
CUTTING TABLE
never grab or touch a live
power cord with wet hands, the
possibility exists of electrical shock,
electrocution, and even death!
never use a damaged or worn
extension cable when connecting
to a power source.Defective cables may cause damage
to the saw’s electric motor or electrical shock.
RULER GUIDE
aLWayS use a grounded (3-wire) extension cord
and maKe CerTaIn that the motor is connected to
a properly grounded electric circuit. If possible use a
ground fault circuit interrupter to protect the operator
from possible electric shock.
RIP GUIDE
Figure 12. Cutting Table
page 20 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
sawing guides
using the rip guide
1. Set the rip guide at the desired location on the ruler
guide and tighten the threaded knob. Make sure that
the rip guide is firmly tightened to avoid slippage. The
rip guide can be used for 45° and 90° cuts.
2. After the rip guide is positioned, for the desired cut,
place material flat against the rip guide and ruler guide.
3. Now you are ready to make your cut.
performing diagonal Cuts
1. Remove threaded knob from the end of the rip guide
with the horizontal groove and insert it into the other
end with the diagonal groove.
2. Set the rip guide onto the ruler guide, such that the top
edgeoftheripguideisalignedwiththediagonalgrooveto
the left of the vertical channel in the cutting table.Tighten
threaded knob once in place.
3. Place one corner of the material being cut in the vertical
slot of the ruler guide and rest the adjoining edge flat
against the rip guide.
4. Now you are ready to make your cut.
performing miter Cuts
Tomakemitercuts,anoptionalmiterblockmustbepurchased.
See Figure 13.
1. Place the lip of the miter block on the ruler guide with
the threaded knob facing you.
2. Position the miter block such that a tile laying flat
against the block may rest its left-most edge within
the vertical channel of the cutting table. Tighten the
threaded knob to secure the miter block in place.
3. Place material onto miter block and you are ready to cut.
Figure 13. Optional Miter Block
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
STarT-up proCedure
WarnIng
never lift the blade guard while the blade
is rotating. The possibility exists of severe
bodily harm if fingers or hands come in
contact with the rotating saw blade. Wait
for the blade to stop rotating before lifting
the blade guard.
NOTICE
Readandfullyunderstandthismanualbefore
starting or attempting to operate the saw.
Before starting the saw’s electric motor
make sure that the Safety, General Information, and
Set-Up sections have been completed and understood.
do noT proceed until the above mentioned sections
have been completed.
1. Place the material to be cut (Figure 14) on the cutting
table against the backstop.
NOTICE
CUTTING
TABLE
aLWayS use the water feed system unless special dry
cut blades are being used. If dry cutting is required,
disconnect water pump.
MATERIAL
WarnIng
BACKSTOP
never place hands or feet inside the belt
guard or blade guard while the motor is
running. aLWayS shut the motor down
before performing any kind of maintenance
Figure 14. Material Placement
danger
WarnIng
aLWayS be alert to the fact that there is a rotating
blade on the saw and be extremely aware of your body
position — especially your hands in relationship to the
rotating blade. The possibility exists of severe bodily
harm or even death if your body comes in contact with
the rotating saw blade.
aLWayS wear approved eye and hearing
protection before operating the saw.
WarnIng
never place hands and fingers near
the cutting blade. The possibility exists of
severe bodily harm if hands and fingers
come in contact with rotating saw blade.
2. Turn the power ON/OFF switch (Figure 15) to the ON
position with the blade away from the material to be
cut, the cutting blade should begin to rotate. Before
cutting remember to follow all safety rules referenced
in this manual.
WarnIng
aLWayS ensure that the cutting blade has
been mounted correctly.
danger
never touch a live power cord with wet
hands.The possibility exists of electrical
shock, electrocution which could cause
severe bodily harm, even death.
Figure 15. Power ON/OFF Switch (ON)
page 22 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn
3. Push the cutting table with the material, slowly and
evenly until the cut is complete. Move the cutting table
back and remove the cut pieces.
4. Avoid overloading the motor when cutting. However,
the electric motor is protected with a manual-reset
thermal overload switch that will turn the saw off if the
motor is overheated. In the event that the switch is
tripped, turn the “ON/OFF”switch to the “OFF”position
and allow the motor to cool before attempting to restart.
SHuT doWn proCedure
1. Place the power ON/OFF switch (Figure 16) in the OFF
position (down).
Figure 16. Power ON/OFF Switch (OFF)
2. Wait for the cutting blade to stop rotating.
3. Disconnect the saw's AC power cord from the power
source. never leave the saw connected to a power
source when unattended. This will prevent accidental
starting.
4. Using a soft cloth, clean any excess debris or residue
that may have accumulated on the saw.
5. Store saw in a clean dry location where it will be out
of the reach of children.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
A good preventive maintenance program of regular
inspection and care will increase life and improve the
performance of the saw and cutting blades.
5. After each day's use, run clean water through the
water pump and water hoses.This extends pump and
blade life.
WarnIng
6. After cleaning, remove all covers and adhesive tape.All
screws or nuts which may have been loosened must
be retightened.
Whenever cleaning, adjusting, or lubricating any part of
the saw, maKe CerTaIn to do the following:
7. Check the spindle bolt for tightness periodically.
• Place power ON/OFF switch to the oFF position.
8. Keep the drive belt tight. It is very important to replace
worn belts as soon as possible.To adjust belt tension,
loosen the four (4) motor mounting bolts and remove
the belt guard. Tighten the adjusting nut on the back
of the motor plate to increase the tension. Proper belt
tension is 4-5 lbs. of force with approximately 3/16" of
belt deflection measured at a point midway between the
pulleys.Tighten the motor mounting bolts and reattach
the belt guard.
• Disconnect power cord from AC source.
• never attempt to check the V-belt with the engine
running. Severe bodily injury can occur.
BaSIC maInTenanCe
1. Tighten loose nuts or screws and replace any cracked
or broken parts.
2. Clean the machine frequently.do noT use aggressive
cleaners (i.e. containing solvents). do noT use high
high-pressure water jets, aggressive detergents or
solutions and liquids with a temperature exceeding
86°. Use a fluff-free cloth only. Use a cloth which may
be lightly moistened only for removing dust and dirt.
Hard packed dirt can be removed with a soft brush.
9. maKe CerTaIn that the cutting head is aligned
properly. Misalignment can adversely affect blade life.
10. The blade flanges must have a diameter of 4".
Undersized flanges will reduce blade life and cause
breakage. Therefore, they should be replaced at
once.
11. Cutting blades must fit the arbor snugly. This is very
important with diamond blades as pounding will occur
and serious blade damage can result. If the arbor
shoulder of the inner blade flange is grooved from blade
slippage, the flange must be replaced.
do noT let any water/cleaning liquid/vapor penetrate
into the electric motor, connectors/plugs, switches, etc.
Cover all apertures, holes in the housing, connectors
or plugs, etc, or seal them with adhesive tape.
Use a soft, low-pressure water jet and a brush to rinse
dirt and incrustations away.Be particularly careful when
near hazardous parts of the machine (e.g. switch,
motor). Clean the motor and switches only by wiping
with a moist cloth.
12. Inspect the cutting table periodically. Replace worn
parts.
13. do noT “rinse” the bearings of the drive elements to
prevent them from running dry.The ball bearings of the
machine are permanently lubricated.
3. Remove the belt guard and clean the pulleys.The belts
and pulleys will wear rapidly if excessive dust builds up.
14. Replace the spindle bearings as soon as they begin to
make any strange noises. Worn bearings can destroy
blades very quickly.
4. Clean the sludge that accumulates on the bottom of
the water tray at least once a day and refill with clean
water. It may be necessary to clean the tray out twice
a day in heavy cutting.The sludge is abrasive and will
shorten the life of the water pump and blades.
15. Grease pivot bearings periodically.
page 24 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
„ Check that the immersion pump works properly. Turn
on the cooling water tap and switch the machine on. If
the pump does not give any water or only a little, switch
the machine off at once. Clean the pump, or replace if
necessary.
maInTenanCe InTervaLS
Use the following guidelines to perform maintenance on
your saw.
after every use of the machine
ambient temperature below 32°F / 0°C (operation
in winter)
„ Remove dirty water from container.
„ Remove dirt and mud from the bottom of the container.
„ To prevent the water in the pump and cooling system
from freezing, remove the water after using the machine
or when there will be a long break. Make sure that the
cooling system is entirely drained so that there is no
water left inside the pump and water hose.
„ Rinse the immersion pump with fresh water to prevent
water pump clogging from residual dirt.
after wet cleaning and before using the machine
again
CLeanIng THe WaTerTray
„ Connect the machine to an electric power outlet
equipped with a“GFCI”safety power breaker.If the safety
power breaker cuts off the electrical power supply, do
not try to operate the machine but have it checked by
an authorized dealer first.
Refer to Figure 17.
1. Remove the rear drip tray.
2. Lift the saw up from inside the water tray.
Before not using the machine for a prolonged
period of time
3. Remove the drain plug and drain any water left inside
the water tray.
4. Flush water into tray while holding it upright to remove
any sludge buildup.
„ Clean and lubricate all movable parts. do noT grease
guide rails.
5. Replace the saw back into the water tray.
6. Attach the rear drip tray.
after not using the machine for a prolonged period
of time
„ Check that the stand is safely fixed.
„ Check that all screw joints and nuts are fixed.
„ Check that the cutting table is seated properly on the
guide rails and that it easily moves along the entire
length of the rails.
„ With the saw blade removed, switch on the motor for an
instant and switch it off again. If the motor does not run,
have the machine inspected by a qualified electrician.
Figure 17. Water Tray Removal
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
WaTer pump maInTenanCe
When the machine has not been used for a long period of
time, hard packed dirt may build up inside the pump and
block the pump wheel.
NOTICE
If the machine is activated with the immersion pump
blocked, the electric motor will be damaged within a
few minutes!
Please follow the steps below to clean the pump before
operating the saw.
1. Remove the immersion pump from the water container.
2. Clean the immersion pump.
Figure 18. Belt Replacement
CuTTIng Head removaL
3. Loosen the fixing screws of the pump lid.
4. Take the lid off the pump (be careful not to damage or
lose the gasket underneath)
To remove the cutting head, see Saw Set-Up
BearIng HouSIng removaL
5. Clean the pump lid.
To remove the bearing housing (Figure 19), perform the
following:
6. Remove all dirt and incrustations from the pump wheel.
7. Check whether the pump wheel can be easily turned.
1. Remove the 4 screws on the belt guard.
2. Remove the belt guard.
8. Reassemble the immersion pump and check that it
works properly.
3. Loosen (do not remove) the adjustment screw behind
the mounting plate and the 4 screws on the motor base
to remove the belt.
BeLT repLaCemenT
To replace the belt (Figure 18) perform the following.
1. Turn off and unplug the saw.
4. Remove the blade lock nut and remove the blade (if
there is one present.)
2. Loosen and remove the 4 bolts located above and
below the belt guard. Remove the belt guard.
5. Remove the 4 screws on the mounting plate closest to
the cutting head handle to remove the bearing housing
(including the attached pulley and inner flange.)
3. Loosen the 4 bolts located at the base of the motor.
4. Use a hex wrench to access the socket hex bolt located
at the rear of the cutting head.Turn wrench to move the
motor forward, thus providing some slack in the belt.
5. Take off the old belt and replace with new belt.
6. To reassemble, follow steps 1-4 in reverse order.Make
sure belt is at the proper tension before tightening the
four bolts at the base of the motor.
page 26 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
BELT
GUARD
BELT
ADJUSTMENT
SCREW
PULLEY
BEARING
HOUSING
INNER
FLANGE
Figure 19. Bearing Housing Removal
BearIng HouSIng InSTaLLaTIon
To install a new bearing housing, perform the following:
1. Make sure that the old housing has been properly
removed.
2. Unpack the new bearing housing and place the flat
portion face-down on a towel situated on a flat surface.
3. Secure the cutting head in a in a completely horizontal
position.
4. Slide the new bearing housing with the flat portion
facing upwards onto the 4 screws located below the
mounting plate. Take care not to damage the inner
flange. Lock the bearing housing into place by using
the brackets and nuts.
5. Pull the motor towards you, place the belt on the
pulleys, and tighten the motor position adjustment
screw. Be sure to leave some slack on the belt.
6. Align the belt by adjusting the motor pulley after
loosening the hex screw.
WarnIng
Do not adjust the bearing housing pulley.
7. After aligning the belt, tighten the hex screw.
8. Replacethebeltguardandlockintoplaceusing4screws.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
required. However, if scenario A or B (described below)
occurs, other adjustments may be required instead.
reaLIgnmenT
method 1
a. If the straight edge only touches the blade when
the table is positioned midway along the rail or at
the ends of the rail, then the rail may be deformed
(i.e. bowed). See Figure 21. Perform test cuts to
determine if the rail should be replaced. Typically,
a bowing displacement of up to 0.2mm (.008 in.)
will not affect cutting accuracy.
This procedure deals with the most common source of
misalignment that occurs when the guide rails are not
parallel with the blade.
1. Set the cutting depth such that the blade passes
through the table, not over.
2. Place a straight edge (i.e. carpenter’s square) on the
cutting table as shown in Figure 20.
3. Loosen the left and right guide rails by loosening the
fasteners found at the ends of the rail. The left rail
should be slightly loose, so there is not too much play
during adjustments, but the right rail should move freely.
Figure 21. Rail Deformation
b. If the straight edge touches both edges of the blade
intially, but shifts apart as the table travels along
the rail, proceed to Method 2.
6. Tighten the fasteners at both ends of the left rail.
7. Adjust the right guide rail so that the horizontal rollers
underneath the table engage the rail as shown in
Figure 22. In most cases the rollers will not have to
be vertically adjusted. Spacing between rails must
be equidistant at all points to ensure that they are
parallel. Once adjustments are made, lightly tighten
the fasteners on the right rail and move the table back
and forth. If the table binds against the rail at any
point, adjust spacing accordingly until the table moves
smoothly.
STRAIGHT
EDGE
RULER
GUIDE
FASTENER
RIGHT
GUIDE
RAIL
LEFT
GUIDE
RAIL
8. Tighten the fasteners at both ends of the right rail.
FRONT
OF THE
If alignment has been achieved, do not proceed to Method 2.
LEAVE HAIRLINE GAP
Figure 20. Realigning Guide Rails
LEAVE A 1/32 IN.
(1MM) GAP
BETWEEN RAIL AND ROLLER
4. Make sure the short portion of the straight edge is placed
flush against the ruler guide. Adjust the left guide rail
so that the front and rear edges of the blade touch the
straight edge, although a tolerance of 0.1mm (.004 in.)
betweenthefrontandrearedgesisallowed. Performthis
adjustment along the entire length of the straight edge.
5. Positionthetableasclosetotheuseraspossible. Placethe
straightedgeflushagainsttherulerguideandblade. Without
holdingontothestraightedge,gentlymovethetabletowards
therearofthesawandthenback. Observeanygapsthatmay
appearbetweenthestraightedgeandbladeorbetweenthe
straight edge and ruler guide. A gap exceeding the allowed
tolerance means that the table is not moving parallel to the
blade;hence,furtheradjustmentsasoutlinedbelowwillbe
Figure 22. Adjust Right Guide Rail
page 28 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
method 2
This procedure corrects another source of misalignment
that occurs when the table’s orientation is not parallel with
the guide rails.
1
GUIDE
ROLLER
1. Use the universal wrench to loosen (but not remove)
the fasteners from either end of both guide rails. Move
each rail away from the other, so that the horizontal
2
HORIZONTAL
ROLLER
rollers are clear of the right guide rail. See Figure 23.
LEFT
GUIDE
RAIL
HORIZONTAL
ROLLER
CLEARANCE
RIGHT
GUIDE
RAIL
Figure 25. Remove Table
3. If the table shifts to the right as it travels away from
the user, a shim needs to be added to the guide roller
furthest from the ruler guide. On the other hand, if
the table shifts to the left, a shim needs to be added
to the guide roller closest to the ruler guide. Remove
the appropriate guide roller to insert a shim between
the roller and table, then reattach. See Figure 26.
Depending on the severity of the shift, more than one
shim may be required.
LOOSEN
FASTENERS
Figure 23. Roller Clearance
2. Remove rubber cap A on the left side of the table.
Loosen the exposed lock nut using a 13mm socket
wrench. Use a flat screwdriver to turn the shaft of the
roller clockwise to lower it by approximately 3/8 in.(9.5
mm). See Figure 24. Evenly lift up the table to
disengage the guide rollers from the left guide rail.
Once the guide rollers are clear, shift the table to the
right to clear the left horizontal roller of the rail. Remove
the table from the guide rails. See Figure 25.
4. After adding shim(s), mount the table onto the guide
rails by reversing the instructions in step 2. Move the
rails toward each other to engage the horizontal rollers
to the right guide rail as shown in Figure 22. Realign
the table to the blade using Method 1. Check to see if
any shifting persists. A shift tolerance of 0.2mm (.008
in.) is allowed. A shift in excess of that will require
RUBBER
CAP A
further adjustment—repeat step 3.
FLAT
FLAT
SCREW
DRIVER
ROLLER
GUIDE
ROLLER
HORIZONTAL
ROLLER
13MM
SOCKET
WRENCH
SHIM
RUBBER
CAP C
RUBBER
CAP B
Figure 26. Add Shims
Figure 24. Lowering Roller
5. Once alignment is successful, replace saw back into
water tray.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance
Leveling adjustment
TranSporTIng THe SaW
This procedure levels the table so that it is perpendicular
to the blade and flush against the rails.
1. Ensure that the water tray is empty and dry.
2. Unplug the power cord and store it in the water tray.
1. Remove rubber caps B and C on the right side of the
table. Loosen the exposed lock nuts using a socket
wrench. Next, use a flat screwdriver to turn the shaft
of the rollers clockwise. See Figure 24. This will lower
the horizontal rollers to allow room for adjusting the
flat rollers.
3. Secure the cutting table to the front of the saw using
the table retention device.
4. Tighten the cutting depth control knob.
5. Optionally, the rear drip tray may be removed and set
in the water tray for better handling.
2. Loosen the socket bolts on the flat roller plate so that
the roller can swing freely about one bolt. see Figure
27. Do this for both flat roller plates.
3. Hold the table against the guide rails. The flat rollers
should reposition themselves to maintain contact with
the guide rails. If the table is not perpendicular to the
blade, lift the right side of the table instead to obtain the
proper angle. A square tool will be required to confirm
the angle. Tighten the socket bolts. Check the table for
play. Repeat step 2 if some play is still present.
4. Restore the horizontal rollers to their original positions
as shown in Figure 22 by reversing the instructions in
step 1. Be sure to tighten the lock nuts and replace
the rubber caps.
FLAT ROLLERS
ROTATE IN
THIS MANNER
Figure 27. Flat Roller Rotation
page 30 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
wiring diagraM (electric MOtOr)
Black
White
Green
Power Outlet for Water Pump
Black
Motor
White
Green
Power Cable
White
Black
White
Black
Switch
Black
Overcurrent
Breaker
Wiring Box
Figure 28. Electric Motor Wiring Diagram
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
trOubleshOOting (blade)
Table 7. Blade Troubleshooting
Symptom
possible problem
Solution
Return saw blade to manufacturer
Have the saw blade aligned/flattened
Chean the receiving flange
Replace saw blade.
Irregular run of the saw blade
Poor tension in the blade material
Saw blade is damaged or bent
Saw blade wobbles when running
Flange of the saw blade is damaged
Shaft of the motor is bent
Replace the saw blade flange
Replace the electric motor
Overheating of the saw blade; cooling water
not sufficient
Diamond segment becomes loose
Excessive wear
Replace saw blade.
Wrong type of saw blade
Shaft of motor causes wobbling
Overheating
Use harder saw blade
Have motor or bearings of motor replaced
Ensure optimum flow of cooling water
Use softer blade
Saw blade too hard
Cracks in or near diamond segment
Fixed flange is worn out
Motor shaft bearing
Have fixed flange replaced
Replace the bearing of the motor shaft
Saw blade type is unsuitable for the material
being cut
Saw blade type is unsuitable for the machine Use appropriate type of saw blade
performance
Saw blade is blunt
Saw blade too hard
Diamond segments are blunt
Replace saw blade.
Poor tension in the blade material
Too much load placed on saw blade
Diamond segments are blunt
Return saw blade to manufacturer
Use a suitable saw blade
Replace saw blade.
Appearance of cut is not optimal
Arbor of the saw blade must be fitted with an
appropriate adapter ring
Center hole in saw blade has become wider Saw blade has slipped on the motor shaft
due to wear
when running
Check the receiving flange and have it
replaced if necessary
Saw blade overheating due to lack of cooling
water
Ensure optimum flow of cooling water
Saw blade shows blooming colors
The material feed is too high; proceed more
slowly
Lateral friction when cutting
Ensure that the direction of the feed is
absolutely parallel to the saw blade
Material is not being fed parallel to saw blade
Adjust roller table
Grinding marks on the saw blade
Poor tension in blade material
Too much load on the saw blade
Have the saw blade tensioned
The material feed is too high; proceed more
slowly
page 32 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
trOubleshOOting (saw)
Table 8. Saw Troubleshooting
Symptom
possible problem
Solution
Check that the machine is properly
connected to the power supply
Power cord not properly fixed/plugged in
Have the power cord checked, replace if
necessary
Power cord defective
Have the main power switch checked and
replaced if necessary by a qualifed electrician
Machine does not run when switched on
Main power switch defective
Loose electrical connection inside the electric Have the whole electric system of the
system
machine checked by a qualified electrician
Have the motor checked and replaced if
necessary by a qualified technician
Motor defective
Too much pressure exerted while cutting
Incorrect specification for saw blade
Exert less pressure when cutting
Use a saw blade which corresponds to the
material being cut
Motor stops (power cuts out)
Have the electric system of the saw checked
by a qualified technician
Saw has a defective electric system
Use a power cord/extension cable of the
rated length, use a cable drum with cable
fully extended
Power cord/extension cable too long or cable
still wound up inside cable drum
Observe the electrical ratings of the machine
and connect it only to a power network which
complies with these ratings
Poor machine performance, little power
Power network is insufficient
Drive motor no longer runs at rated speed
(RPM)
Have the motor checked by a qualified
electrician and replace if necessary
The water pump draws air
Fill the water tray with water
Insufficient flow of cooling water or no cooling Filter clogged
water at all
Clean the filter of the water pump
Pump wheel of the immersion pump is
blocked by dirt
Disassemble the immersion pump and clean it
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
explanatiOn Of cOde in reMarks cOluMn
The following section explains the different symbols and
QTy. Column
remarks used in the Parts section of this manual. Use the
help numbers found on the back page of the manual if there
are any questions.
numbers used — Item quantity can be indicated by a
number, a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other
parts that are sold in bulk and cut to length.
NOTICE
The contents and part numbers listed in the parts
section are subject to change without notice.Multiquip
does not guarantee the availability of the parts listed.
A blank entry generally indicates that the item is not sold
separately.Other entries will be clarified in the“Remarks”
Column.
SampLe parTS LIST
remarKS Column
no. parT no. parT name
QTy. remarKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed
to describe the item can also be shown.
1
2%
12345
BOLT .....................1 .....INCLUDES ITEMS W/%
WASHER, 1/4 IN. ..........NOT SOLD SEPARATELy
WASHER, 3/8 IN. ..1 .....Mq-45T ONLy
2% 12347
3
4
12348
12349
HOSE ..................A/R ...MAKE LOCALLy
BEARING ..............1 .....S/N 2345B AND ABOVE
assembly/Kit — All items on the parts list with the
same unique symbol will be included when this item is
purchased.
no. Column
Indicated by:
unique Symbols — All items with same unique
symbol
“INCLUDES ITEMS W/(unique symbol)”
(@, #, +, %, or >) in the number column belong to the
same assembly or kit, which is indicated by a note in the
“Remarks” column.
Serial number Break — Used to list an effective serial
number range where a particular part is used.
Indicated by:
duplicate Item numbers — Duplicate numbers indicate
multiple part numbers, which are in effect for the same
general item, such as different size saw blade guards in
use or a part that has been updated on newer versions
of the same machine.
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Specific model number use — Indicates that the part
is used only with the specific model number or model
number variant listed. It can also be used to show a
part is NOT used on a specific model or model number
variant.
NOTICE
When ordering a part that has more than one item
number listed, check the remarks column for help in
determining the proper part to order.
Indicated by:
“XXXXX ONLy”
“NOT USED ON XXXX”
parT no. Column
numbers used — Part numbers can be indicated by a
number, a blank entry, or TBD.
“make/obtain Locally” — Indicates that the part can
be purchased at any hardware shop or made out of
available items.Examples include battery cables, shims,
and certain washers and nuts.
TBD (To Be Determined) is generally used to show a
part that has not been assigned a formal part number
at the time of publication.
“not Sold Separately”— Indicates that an item cannot
be purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available
for sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will
be clarified in the “Remarks” Column.
page 34 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
suggested spare parts
Tp24 TILe SaW WITH eLeCTrIC moTor
1 to 3 units
Qty.
1............TP100072.............V-BELT
p/n
description
1............TPS100003...........SWITCH, TOGGLE 15A
1............TP100152.............CARBON BRUSH
NOTICE
Part numbers on this Suggested Spare Parts list may
supersede/replace the part numbers shown in the
following parts lists.
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Main saw assy.
9
8
3
14
12
2
13
CUTTING
TABLE
15
28
28
8
26
21
9
21
27
26
27
5
1
6
4
page 36 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
Main saw assy.
no.
1
2
3
4
5
6
8
9
12
13
14
15
21
26
27
parT no.
TP100125
TP100127
TP100129
TP100143
TP100144
TP100140
TP100138
TP100139
TP100141
TP100080
TP100086
TP100132
TP100109
TP100080
TP100141
parT name
FRAME ASSy
CUTTING HEAD ASSy
10" BLADE GUARD ASSy
WATER TRAy
WATER TRAy, BACK DRIP
PLUG, WATER TRAy
M10 SPRING WASHER
KNOB, M8 X 1.25 X 20L
WASHER, M8
WASHER SPRING M10
NUT, M8 X 1
WATER PUMP, 230 GAL/HR
BOLT, HEX M8 X 1.25 X 16L
WASHER, SPRING M8
WASHER, NARROW M8
QTy.
1
1
1
1
1
1
2
1
1
1
1
1
4
4
4
remarKS
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
cutting head assy.
SWITCH
BOX
ASSY.
28
24
36
4
20
17
23
18
35
21
18
23
23
21
21
22
34
15
16
18
21
23
7
18
1
2
27
13
3
44
43
47
10
25
46
45
11
12
BEARING
HOUSING
ASSY.
6
6
14
14
page 38 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
cutting head assy.
no.
1
2
3
4
parT no.
TP100064
TP100068
TP100069
TP100067
TP100077
TP100074
parT name
QTy.
remarKS
MOUNTING PLATE
SHAFT, BLADE GUARD
BRACKET, BELT GUARD
BELT GUARD
BRACKET, LCBH
BRACKET, MOTOR TENSION
1
1
1
1
2
1
6
7
10
11
12
13
14
15
16
17
18
20
21
22
23
24
25
27
28
34
35
36
43
44
45
46
47
BLADE, 10" GENERAL PURPOSE...................1................CONTACT UNIT SALES
TP100136
TP100137
TP100075
TP100086
TP100085
TP100142
TP0120
FLANGE, UNIVERSAL, DIA 5/8"
NUT, 5/8-11 UNC
1
1
1
4
4
1
2
4
2
4
1
4
2
4
1
1
1
1
1
4
4
2
2
1
RUBBER STOP, CIRCULAR D6
NUT, NyLON M8 X 1.25
BOLT, HHSC M8 X 1.25 X 70L X 28
WASHER, M8
WASHER, M8 NARROW
WASHER, NARROW M6
WASHER, M8 LOCK
TP100061
TP0121
TP100081
TP100083
TP100062
TP100087
TP100082
TP100072
TP100066
TP100092
TP100093
TP100094
TP100080
TP100079
TP100084
TP100061
TP100073
WASHER, SPRING M5
BOLT, HHSC, M8 X 1.25 X 55L X 28
BOLT, HEX M6 X 1 X 10L
BOLT, HEX, M8 X 1.25 X 12L
NUT, M8 X 1
V-BELT, 23"
MOTOR ASSy
PULLEy, MOTOR
KEy, SqUARE 5 X 5 X 30L
SET SCREW, FLAT POINT, M6 X 1 X 10L
WASHER, SPRING M8
WASHER, NARROW M8
BOLT, HHS M6 X 1 X 20L
WASHER, NARROW M6
HANDLE, RECTANGLE 26.5H X 7W X 93L
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
electric MOtOr assy.
7
5
10
12
6
14
16
8
2
9
3
9
15
8
13
11
1
4
page 40 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
electric MOtOr assy.
no.
1
2
3
4
5
6
7
8
parT no.
TP100145
TP100146
TP100147
TP100148
TP100082
TP100149
TP100150
TP100151
TP100152
TP100153
TP100154
TP100155
TP100156
TP100157
TP100158
TP100159
parT name
MOUNTING BLOCK
MOTOR ASSy, M2 2HP
BOLT, HEX M8 X 1.25 X 25L
BOLT, COUNTERSUNK SOCKET, M8 X 1.25 X 30L
NUT, NyLON M8 X 1.25
ARMATURE AND WINDING ASSy
MOTOR COVER
CAP, CARBON BRUSH
CARBON BRUSH, 17MM X 7 M (SET OF 2)
WIND BAFFLE
WASHER, SPRING M5
WASHER, SPRING M4
WASHER, NARROW M5
WASHER, NARROW M4
CROSS SCREW, M5 X .8 X 25L
CROSS SCREW, M4 X .7 X CROSS SCRE
QTy.
1
1
4
1
4
1
1
2
1
1
4
4
4
4
4
remarKS
9
10
11
12
13
14
15
16
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
cutting table assy.
8
8
11
1
8
11
2
2
4
SIDE EXTENSION
TABLE (OPTION)
18
12
19
18
12
15
12
11
15
5
11
11
17
17
9
13
6
3
16
10
9
14
16
3
3
12
page 42 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
cutting table assy.
no.
1
2
3
4
5
6
8
9
10
11
12
13
14
15
16
17
18
19
parT no.
TP100095
TP100097
TP100098
TP100099
TP100100
TP100101
TP100103
TP100105
TP0322
parT name
CUTTING TABLE
GUIDE ROLLER (SET OF 2)
CONCENTRIC FLAT ROLLER
RULER GUIDE
SPRING LOCK ASM
SPRING
RUBBER CAP
FLAT ROLLER ASM (SET OF 2)
HEX BOLT M6X1.0X10L
NUT M8X1
WASHER LOCK M8
WASHER LOCK M6
HEX BOLT M6X1.0X30L
HEX BOLT M8X1.25X25L
HEX BOLT M8X1.25X20L
WASHER NARROW M6
WASHER NARROW M8
HEX BOLT M8X1.25X20L
QTy.
1
1
3
1
1
1
3
1
1
9
12
1
1
2
4
2
6
remarKS
TP100082
TP0121
TP100081
TP25095
TP100107
TP100108
TP0384
TP0120
TP100109
4
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
blade guard assy.
12
11
8
9
1
10
3
10
2
6
10
4
5
7
3
13
page 44 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
blade guard assy.
no.
1
2
3
4
5
6
7
8
parT no.
TP100051
TP100053
TP100054
TP100055
TP100056
TP110057
TP100058
TP100059
TP100060
TP481101
TP100061
TP0322
parT name
BLADE GUARD
M3 RIVET
PLASTIC BRUSHES
RETAINING CLIP
WATER BAFLE PLATE
WATER TUBE
D6.4MM 90° ELBOW PIPE
D8 90° ELBOW HOSE CONNECTOR
RUBBER SPLASH GUARD
M5 RIVET
QTy.
remarKS
1
1
2
1
1
1
1
1
1
4
3
3
1
9
10
11
12
13
WASHER NARROW M6
HEX BOLT M6X1.0X10L
CROSS SCREW M4X0.7X8L
TP0353
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
bearing hOusing assy.
15
14
13
7
1
12
5
16
10
5
2
11
8
3
4
6
9
page 46 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
bearing hOusing assy.
no.
1
2
3
4
5
6
7
8
parT no.
TP100110
TP100112
TP100113
TP100114
TP100116
TP110017
TP100118
TP100119
TP1374
TP100120
TP100121
TPS1000062
TP0316
TP100122
TP100123
TP100124
parT name
QTy.
1
1
1
1
2
1
1
1
4
1
1
1
1
1
1
1
remarKS
BEARING HOUSING
BLADE SHAFT
RUBBER GASKET
WATER CHANNEL COVER
MALE CONNECTOR, M10 TO D7.5
WATER LINK ASM
BLADE SHAFT PULLEy
INNER ARBOR FLANGE
CROSS SCREW M4X0.7X8L
BEARING RADIAL D40
BEARING RADIAL D47
KEy, SqUARE 5X5X30L
SET SCREW FLAT PT M6X1.0X10L
HOSE, BLADE GUARD
HOSE, WATER PUMP
M17 E-CLIP
9
10
11
12
13
14
15
16
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
switch bOx assy.
15
6
17
9
13
7
14
5
10
16
4
3
11
2
10
1
12
page 48 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
switch bOx assy.
no.
1@
2@
3@
4@
5@
6@
7@
9@
parT no.
TP420280
TP420281
TP420282
TP420283
TPS100003
TPS100004
TP420286
TP110032
parT name
QTy.
1
1
1
1
1
1
1
2
6
1
2
1
1
1
2
remarKS
SWITCH BOX HOUSING
2 CABLE D9 CABLE GROMMET
2 CABLE D9 CABLE BOOT
CABLE CLAMP
SWITCH, TOGGLE 15A
CIRCUIT BREAKER RESET 20A
SWITCH BOX COVER
SCREW CROSS M3X0.5X8L
SCREW CROSS M4X0.7X8L
JUNCTION BOX
SCREW CROSS M4X0.7X15L
SHIELD POWER SWITCH
BOOT POWER SWITCH
BOOT RESET BUTTON
NUT, M4 X 0.7
10@ TP1374
11@ TP420290
12@ TP03531
13@ TP420291
14@ TPS1000032
15@ TPS1000041
16@ TP420294
17
TP100076
POWER SWITCH ASSy....................................1................INCLUDES ITEMS W/@
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
tOOls and accessOries
1
2
3
4
5
7
6
page 50 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
tOOls and accessOries
no.
1
2
3
4
5
6
7
parT no.
parT name
UNIVERSAL WRENCH
MASTER GUIDE TEMPLATE BASE..................1................OPTIONAL
45°/90° RIP GUIDE
MITER BLOCK...................................................1................OPTIONAL
MASTER GUIDE................................................1................OPTIONAL
SIDE EXTENSION TABLE.................................1................OPTIONAL
SAW STAND ......................................................1................OPTIONAL
QTy.
1
remarKS
TPS100041
TPS1000MG1
TPS100035
TPS100034
TPS1000MG
TP100102
1
TPSDT1010ST
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
terMs and cOnditiOns Of sale — parts
5. Parts must be in new and resalable
condition, in the original Multiquip
package (if any), and with Multiquip part
numbers clearly marked.
Multiquip reserves the right to quote and
sell direct to Government agencies, and to
Original Equipment Manufacturer accounts
who use our products as integral parts of their
own products.
paymenT TermS
Terms of payment for parts are net 30 days.
FreIgHT poLICy
6. The following items are not returnable:
All parts orders will be shipped collect or
prepaid with the charges added to the invoice.
All shipments are F.O.B. point of origin.
Multiquip’s responsibility ceases when a
signed manifest has been obtained from the
carrier, and any claim for shortage or damage
must be settled between the consignee and
the carrier.
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
SpeCIaL eXpedITIng ServICe
A $35.00 surcharge will be added to the
invoice for special handling including bus
shipments, insured parcel post or in cases
where Multiquip must personally deliver the
parts to the carrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
prior to the return date.
LImITaTIonS oF SeLLer’S LIaBILITy
mInImum order
Multiquip shall not be liable hereunder for
damages in excess of the purchase price of
the item with respect to which damages are
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
other special, consequential or incidental
damages.
The minimum charge for orders from Multiquip
is $15.00 net. Customers will be asked for
instructions regarding handling of orders not
meeting this requirement.
c. Any line item with an extended
dealer net price of less than
$5.00.
d. Special order items.
reTurned goodS poLICy
e. Electrical components.
f. Paint, chemicals, and lubricants.
g. Decals and paper products.
h. Items purchased in kits.
Return shipments will be accepted and
credit will be allowed, subject to the following
provisions:
LImITaTIon oF WarranTIeS
No warranties, express or implied, are
made in connection with the sale of parts or
trade accessories nor as to any engine not
manufactured by Multiquip. Such warranties
made in connection with the sale of new,
complete units are made exclusively by a
statement of warranty packaged with such
units, and Multiquip neither assumes nor
authorizes any person to assume for it
any other obligation or liability whatever in
connection with the sale of its products. Apart
from such written statement of warranty,
there are no warranties, express, implied or
statutory, which extend beyond the description
of the products on the face hereof.
1. A Returned Material Authorization
must be approved by Multiquip prior to
shipment.
7. The sender will be notified of any material
received that is not acceptable.
8. Such material will be held for five
working days from notification, pending
instructions. If a reply is not received
within five days, the material will be
returned to the sender at his expense.
2. To obtain a Return Material Authorization,
a list must be provided to Multiquip
Parts Sales that defines item numbers,
quantities, and descriptions of the items
to be returned.
9. Credit on returned parts will be issued
at dealer net price at time of the original
purchase, less a 15% restocking
charge.
a. The parts numbers and descriptions
must match the current parts price
list.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
based on the list price that was effective
twelve months prior to the RMA date.
c. The list must state the reason(s)
for the return.
Effective: February 22, 2006
d. The list must reference the sales
order(s) or invoice(s) under
which the items were originally
purchased.
11. Credit issued will be applied to future
purchases only.
prICIng and reBaTeS
e. The list must include the name
and phone number of the person
requesting the RMA.
Prices are subject to change without prior
notice. Price changes are effective on a
specific date and all orders received on or
after that date will be billed at the revised price.
Rebates for price declines and added charges
for price increases will not be made for stock
on hand at the time of any price change.
3. AcopyoftheReturnMaterialAuthorization
must accompany the return shipment.
4. Freight is at the sender’s expense. All
parts must be returned freight prepaid to
Multiquip’s designated receiving point.
page 52 — Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12)
Download from Www.Somanuals.com. All Manuals Search And Download.
nOtes
Tp24 TILe SaW • operaTIon and parTS manuaL — rev. #2 (04/12/12) — page 53
Download from Www.Somanuals.com. All Manuals Search And Download.
OperatiOn and parts Manual
HERE’S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
United StateS
Multiquip Corporate Office
MQ Parts Department
18910 Wilmington Ave.
Carson, CA 90746
Contact: [email protected]
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax: 800-672-7877
Fax: 310-637-3284
Service Department
Warranty Department
800-421-1244
310-537-3700
Fax: 310-537-4259
Fax: 310-943-2238
800-421-1244
310-537-3700
Fax: 310-943-2249
Technical Assistance
800-478-1244
mexico
United Kingdom
MQ Cipsa
Multiquip (UK) Limited Head Office
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla 72760 Mexico
Contact: [email protected]
Tel: (52) 222-225-9900
Unit 2, Northpoint Industrial Estate, Tel: 0161 339 2223
Fax: (52) 222-285-0420 Globe Lane,
Dukinfield, Cheshire SK16 4UJ
Contact: [email protected]
Fax: 0161 339 3226
Canada
Multiquip
4110 Industriel Boul.
Laval, Quebec, Canada H7L 6V3
Contact: [email protected]
Tel: (450) 625-2244
Tel: (877) 963-4411
Fax: (450) 625-8664
© COPYRIGHT 2012, MULTIQUIP INC.
Multiquip Inc, the MQ logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other trademarks are the property
of their respective owners and used with permission.
This manual MUsT accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations, descriptions, references and technical data contained in
this manual are for guidance only and may not be considered as binding. Multiquip Inc. reserves the right to discontinue or change specifications, design or the information published
in this publication at any time without notice and without incurring any obligations.
your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|