OPERATION AND PARTS MANUAL
Vibratory
Walk-Behind Roller
Model
MDR-9GH
(Honda Gasoline)
Revision #0 (12/17/03)
MULTIQUIPINC.
18910 WILMINGTON AVE.
PARTS DEPARTMENT:
800-427-1244
CARSON, CALIFORNIA 90746 FAX: 800-672-7877
310-537-3700
800-421-1244
SERVICE DEPARTMENT/TECHNICAL ASSISTANCE:
800-478-1244
FAX:310-537-3927
FAX:310-631-5032
Atlanta • Boise • Dallas • Houston • Newark
Montreal, Canada • Manchester, UK
Rio De Janiero, Brazil • Guadalajara, Mexico
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP’SMAINPHONENUMBERS
800-421-1244
310-537-3700
FAX: 310-537-3927
PARTSDEPARTMENT
800-427-1244
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
MAYCOPARTS
800-306-2926
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
SERVICEDEPARTMENT
800-478-1244
310-537-3700
FAX: 310-537-4259
MQPOWERSERVICEDEPARTMENT
800-835-2551
310-537-3700
FAX: 310-638-8046
TECHNICALASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTYDEPARTMENT
800-421-1244, EXT. 279 FAX: 310-537-1173
310-537-3700, EXT. 279
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
MIKASA MDR-9GH-
VIBRATORY ROLLER
HONDA GX340K1QAE2
ENGINE
Proposition 65 Warning ............................................. 2
Here's How To Get Help ............................................ 3
Table Of Contents ..................................................... 4
Parts Ordering Procedures ....................................... 5
Specifications ............................................................ 6
Dimensions ............................................................... 7
Safety Message Alert Symbols .............................. 8-9
Rules for Safe Operation ................................... 10-11
Operation and Safety Decals .................................. 12
General Information ........................................... 14-15
Vibratory Roller Components.................................. 16
Engine Components ............................................... 17
Inspection/Start-Up ........................................... 20-21
Operation/Lifting/Transporting ........................... 22-23
Maintenance ...................................................... 24-29
Engine Troubleshooting...................................... 30-31
Roller Troubleshooting ............................................ 32
Explanation Of Code In Remarks Column .............. 34
Suggested Spare Parts ........................................... 35
Air Cleaner Assembly......................................... 68-69
Camshaft Assembly ........................................... 70-71
Carburetor Assembly ......................................... 72-73
Control Assembly ............................................... 74-75
Control Box Assembly ........................................ 76-77
Crankcase Cover Assembly............................... 78-79
Crankshaft Assembly ......................................... 80-81
Cylinder Barrel Assembly................................... 82-83
Cylinder Head Assembly .................................... 84-85
Fan Cover Assembly .......................................... 86-87
Flywheel Assembly ............................................ 88-89
Fuel Tank Assembly ........................................... 90-91
Ignition Coil Assembly ........................................ 92-93
Starter Motor Assembly ..................................... 94-95
Muffler Assembly ............................................... 96-97
Piston Assembly................................................. 98-99
Recoil Starter Assembly................................. 100-101
Labels Assembly ............................................102-103
Terms and Conditions of Sale ............................... 104
PARTS ILLUSTRATIONS
Decal Placement ................................................ 36-37
Body Assembly .................................................. 38-39
Front Cover Assembly........................................ 40-43
Axle Assembly .................................................... 44-47
Transmission Assembly...................................... 48-49
Hydraulic Oil Tank Assembly ............................. 50-51
Clutch Box Assembly ......................................... 52-55
Vibration Case Assembly ................................... 56-57
Upper Control Handle Assembly........................ 58-61
Lower Control Handle Assembly........................ 62-63
Engine Assembly ............................................... 64-65
Battery Assembly ............................................... 66-67
Specification and part
number are subject to
change without notice.
PAGE 4 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
✓
✓
✓
✓
✓
✓
FedEx or UPS Ground
FedEx or UPS Second Day or Third Day
FedEx or UPS Next Day
Federal Express Priority One
DHL
Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number on
hand when calling.
Parts Department
800-427-1244
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Extra Discounts!
All parts orders which include complete part numbers
and are received by our automated web parts order
system, or by fax qualify for the following extra
discounts:
Mayco Parts
800-306-2926
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Ordered
via
Standard
orders
Stock orders
($750 list and above)
Service Department
800-478-1244
310-537-3700
Fax:310-537-4259
Fax
3%
5%
10%
10%
Web
MQ Power Service Department
800-835-2551
310-537-3700
Fax:310-638-8046
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
Technical Assistance
800-478-1244
Fax:310-631-5032
Fax:310-537-1173
Warranty Department
800-421-1244, Ext. 279
310-537-3700, Ext. 279
No other allowances on freight shipped by any other
carrier.
Multiquip’s Main Phone Numbers
NOTE:DISCOUNTSARESUBJECTTOCHANGE
800-421-1244
310-537-3700
Fax:310-537-3927
Direct TOLL-FREE access
to our Parts Department:
Toll-free nationwide — 800-427-1244
MULTIQUIP INC.
18910 WILMINGTON AVENUE
POST OFFICE BOX 6254
CARSON, CALIFORNIA 90749
310-537-3700•800-421-1244
FAX:310-537-3927
WWW:multiquip.com
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH —SPECIFICATIONS
Table 1. MDR-9GH VIBRATORY ROLLER SPECIFICATIONS
Centrifugal Force
Vibration Frequency
Traveling Speed (forward and reverse)
Grade Ability
6,600 lbs. (3,000 kg)
3,000 vpm
0 to 1.8 mph (0 to 3 km/hr)
25°
Diameter x Width of Roller
Wheel Base
18 x 27.6 in (457 x 700 cm)
22.4 in (570 mm)
10.8 in (274 mm)
111.8 in (2,840 mm)
31.3 in (795 mm )
44.1 in (1,120 mm )
1,940 lbs. (880 kg)
2,000 rpm
Side Road Clearance
Length (with Handle)
Width
Height
Total Weight
Working Input Revolution
Continuous Rated Pressure
Oil Tank Capacity
Water Tank Capacity
Working Ability
1,500 psi (105 kg/cm2)
4 gallons (15 liters)
6 gallons (23 liters)
2,100 m2/hr
Table 2. ENGINE SPECIFICATIONS
Model
HONDA GX340K1QAE2
Air-cooled 4 stroke, Single Cylinder, OHV,
Horizontal Shaft Gasoline Engine
Type
2.90 in. X 2.30 in.
(73 mm x 58 mm.)
Bore X Stroke
Displacement
23.70 cu-in (389 cm3)
11.0 H.P./3600 R.P.M.
1.72 gallons (6.5 liters)
Unleaded Automobile Gasoline
1.16 quarts (1.1 liters)
Yes
Max Output
Engine
Fuel Tank Capacity
Fuel
Lube Oil Capacity
Oil Alert System
Speed Control Method
Starting Method
Centrifugal Fly-weight Type
Electric/Recoil Start
Dimension
(L x W x H)
15.0 x 17.7 X 17.4 in.
(380 X 450 X 443 mm.)
Dry Net Weight
68.4 lbs (31 Kg.)
PAGE 6 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — DIMENSIONS
Figure 2. MDR-9GHVibratory Roller Dimensions
TABLE 3. ROLLER DIMENSIONS
REF.
A
DIMENSIONS
REF.
F
DIMENSIONS
111.8 in. (2.8 meters)
88 in. (2.23 meters)
46 in. (1.17 meters)
45.9 in. (1.16 meters)
11 in. (.279 meters)
22.4 in. (.57 meters)
18 in. (.457 meters)
15.5 in. (.382 meters)
5.4 in. (.137 meters)
B
G
C
H
I
D
E
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — SAFETY MESSAGE ALERT SYMBOLS
HAZARD SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
Safety precautions should be followed at all times when
operating this equipment. Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
Lethal Exhaust Gases
This Owner's Manual has
been developed to provide
complete instructions for
Engine exhaust gases contain poisonous
carbon monoxide. This gas is colorless and
odorless, and can cause death if inhaled.
NEVER operate this equipment in a confined
area or enclosed structure that does not
provide ample free flow air.
the safe and efficient
operation of the Multiquip
Model MDR-9GH Vibration
Roller. Refer to the engine
manufacturer’s instructions for
data relative to its safe
operation.
Explosive Fuel
Before using this vibratory roller, ensure that the operating
individual has read and understands all instructions in this
manual.
GASOLINE is extremely flammable, and its
vapors can cause an explosion if ignited. DO
NOT start the engine near spilled fuel or
combustible fluids. DO NOT fill the fuel tank
while the engine is running or hot. DO NOT
overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or
sparks from the ignition system. Store fuel in
approved containers, in well-ventilated areas
and away from sparks and flames. NEVER
use fuel as a cleaning agent.
SAFETY MESSAGE ALERT SYMBOLS
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure to
the operator, and are preceded by one of three words: DANGER,
WARNING, or CAUTION.
Burn Hazards
DANGER: You WILL be KILLED or
SERIOUSLY injured if you do not follow
directions.
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after
operations. Never operate the engine with heat
shields or heat guards removed.
WARNING: You CAN be KILLED or
SERIOUSLY injured if you do not follow
directions.
Rotating Parts
CAUTION: You CAN be injured if you
do not follow directions.
NEVER operate equipment with covers, or
guards removed. Keep fingers, hands, hair and
clothing away from all moving parts to prevent
injury.
Potential hazards associated with this vibratory roller operation
will be referenced with Hazard Symbols which appear
throughout this manual, and will be referenced in conjunction
with Safety Message Alert Symbols.
PAGE 8 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — SAFETY MESSAGE ALERT SYMBOLS
Accidental Starting
Respiratory Hazard
ALWAYS place the engine ON/OFF switch in
the OFF position, when the vibration roller is
not in use.
ALWAYS wear approved respiratory
protection.
Equipment Damage Messages
Sight and Hearing hazard
Other important messages are provided throughout this manual
to help prevent damage to your vibration roller, other property,
or the surrounding environment.
ALWAYS wear approved eye and hearing
protection.
This vibratory roller, other
property, or the surrounding
environment could be
damaged if you do not follow
instructions.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — RULES FOR SAFE OPERATION
CAUTION:
Failure to follow instructions in this manual
may lead to serious injury or even death!This
equipment is to be operated by trained and
qualified personnel only! This equipment is
for industrial use only.
■
NEVER touch the hot exhaust manifold,
muffler or cylinder. Allow these parts to
cool before servicing engine orvibratory
roller.
The following safety guidelines should always be used when
operating the MIKASA MDR-9GHVibratory Roller.
■
■
HighTemperatures – Allow the engine to cool before adding
fuel or performing service and maintenance functions. Contact
with hot components can cause serious burns.
The engine of this vibratory roller requires an adequate free
flow of cooling air. NEVER operate the vibratory roller in any
enclosed or narrow area where free flow of the air is restricted.
If the air flow is restricted it will
cause serious damage to the
vibratory roller or engine and
may cause injury to people and
property.Remember the roller’s
GENERAL SAFETY
■
■
■
DO NOT operate or service this equipment before
readingthisentiremanual.
This equipment should not be operated by
persons under 18 years of age.
NEVER operate this equipment without proper
protective clothing, shatterproof glasses, steel-
toed boots and other protective devices required
by the job. ALWAYS wear slip resistant safety
shoes or boots.
enginegivesoff DEADLY gases.
■
■
ALWAYS refuel in a well-ventilated area, away from sparks
and open flames.
■
■
■
NEVER operate this equipment when not feeling
well due to fatigue, illness or taking medicine.
ALWAYS use extreme caution when working with flammable
liquids. When refueling, stop the engine and allow it to cool.
DO NOT smoke around or near the machine. Fire or
explosion could result from fuel vapors, or if fuel is spilled on
a hot engine.
NEVER operate this equipment under the
influence or drugs or alcohol.
■
NEVER operate the vibratory roller in an explosive
atmosphere or near combustible
materials. An explosion or fire could
result causing severe bodily harm or
even death.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage to
the equipment and/or injury to user may result.
■
■
■
Manufacturer does not assume responsibility for any accident
due to equipment modifications.
■
■
■
Topping-off to filler port is dangerous, as
it tends to spill fuel.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
ALWAYS store the vibratory roller in a clean, dry location out
of the reach of children.
ALWAYS wear proper respiratory (mask), hearing and eye
protection equipment when operating the vibratory roller.
NEVER run engine without air cleaner. Severe engine
damage may occur.
■
■
NEVER leave the vibratory roller unattended, turn off engine.
CAUTION must always be observed while servicing this
vibratory roller. Rotating parts can cause injury if contacted.
■
DO NOT leave vibratory roller with engine running. Use
chock blocks if parking vibratory roller on a grade.
PAGE 10 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — RULES FOR SAFE OPERATION
■
NEVER disconnect any "emergency or safety devices".
These devices are intended for operator safety. Disconnection
of these devices can cause severe injury, bodily harm or even
death! Disconnection of any of these devices will void all
warranties.
■
ALWAYS know the location of the nearest and first aid kit.
Loading and Unloading (Crane)
■
Before lifting, make sure that machine parts (hook and
vibration insulator) are not damaged and screws are not
loosened or lost.
■
In emergencies always know the location of the
nearest phone or keep a phone on the job site.
Also know the phone numbers of the nearest
ambulance, doctor and fire department. This
information will be invaluable in the case of an
emergency.
■
Always make sure crane or lifting device has been properly
secured to the hook of guard frame on vibratory roller.
■
■
■
■
NEVER lift the machine while the engine is running.
Use adequate lifting cable (wire or rope) of sufficient strength.
Use one point suspension hook and lift straight upwards.
NEVER allow any person or animal to stand underneath the
machine while lifting.
■
Try not to lift machine to unnecessary heights.
Transporting
■
■
Always shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to prevent
fuel from spilling.
■
■
Drain fuel when transporting vibratory roller over long
distances or bad roads.
Always tie-down the vibratory roller during transportation by
securing the roller's guard frame with rope.
Emergencies
ALWAYS know the location of the nearest fire extinguisher.
Maintenance Safety
■
■
NEVER lubricate components or attempt service on a
running machine.
■
ALWAYS allow the machine a proper amount of time to
cool before servicing.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always replace
broken parts.
■
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
■
■
DO NOT use food or plastic containers to dispose of
hazardous waste.
DO NOT pour waste, oil or fuel directly onto the ground,
down a drain or into any water source.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — OPERATION AND SAFETY DECALS
Figure 1 displays the operation and safety decals as they appear on the vibratory roller. Should any of these decals become
damaged or unreadable, contact the Multiquip Parts Department for a replacement set.
Figure 1. Operation and Safety Decals
PAGE 12 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — GENERAL INFORMATION
FREQUENCY/SPEED
The Mikasa Model MDR-9GH is a powerful compacting tool
capable of applying a tremendous force in consecutive impacts
to a soil surface. With 28-inch drums and 32 inches overall width,
virtually any asphalt or mixed granular soil compaction job is
quickly cut down to size.
The vibrating roller maximum frequency is 3000 vpm (vibrations
per minute).The forward and reverse travel speed of the vibratory
roller is approximately 1.8 mph (3 km/hour).
ENGINE
The impact force of the MDR-9GH levels and uniformly
compacts voids between soil particles to increase dry density.
The Mikasa MDR-9GH Vibratory Roller is equipped with a
HONDA GX340KQAE2 engine.
Features include:
CONTROLS
„
Hydraulic variable speed transmission assures easy
handling.
Before starting the MDR-9GH Vibratory Roller, identify and
understand the function of the controls and components as
indicated in Figure 6.
„
Deadman device which when pressed or hit will
cause the travel lever to return to neutral position
bringing the machine to a stop.
TRANSPORTATION
Adjustable transport hooks allow an operator to place the roller
on the tailgate of a dump truck without any assistance. The
control handle of the MDR-9GH Vibratory Roller can be folded
vertically for ease of transport and storage.
„
„
Non-corrosive water tank for the sprinkler system with a
capacity of 6 gallons.
Simple dual-lever controls assure operator safety and
convenience.
LIFTING THE ROLLER
„
„
„
Sight gauge for hydraulic oil tank.
Front -mounted auxiliary travel lever.
When lifting of the roller is required (Figure 3), attach a suitable
hook or shackle to the lifting hooks of the roller.Make sure the
lifting device is capable of lifting 1,940 lbs (880 kg).
Four large rubber shock mounts minimize vibrations to the
engine and hydraulics.
„
„
„
„
Convenient tie-downs, front and rear.
Scraper Bar.
Drum sprinkler system.
Handle folds to 90 degrees for storage and transport..
Figure 3. LiftingThe Roller
PAGE 14 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — GENERAL INFORMATION
CAUTION :
CAUTION :
CAUTION :
Tipping (Rollovers)
NEVER! operate the roller on side slopes (Figure 5). The
possibility exist that the roller could tip over (roll over), thus
causing bodily harm even death and serious damage to the
equipment.
NEVER! stand under, or get onto the roller
while it is being lifted or moved.
ONLY! use steel ropes or chains that are
capable of lifting at least 1,940 lbs. (880 kg ).
NEVER! use any other part of the roller for
lifting purposes. Use the lifting eye. Using other
parts of the roller for lifting will cause severe
damage to the roller,
Figure 5. Recommended Slope
In the event the roller does tip over, extreme care must be taken
to prevent damage to the engine. When the roller has been
tipped over, oil from the engine crankcase can flow into the
combustion chamber, which can severely damage the engine
the next time it is started.
OPERATING ON SLOPES
Special care must be taken when operating the roller on hills or
slopes. There exist the possibility of serious injury to the operator
and severe damage to the roller in the event of a roll over.
ALWAYS operate the roller up and down hills rater than from
side to side. For safe operation hillside slopes should not exceed
12 degree (21 % grade). See Figure 4 below.
IMMEDIATELY after a unit has tipped over upright the unit as
soon as possible to prevent oil from leaking into the combustion
chamber.
CAUTION :
To prevent damage to the engine after a
rollover, the unit must NOT be started.
NEVER start a unit after a rollover.CONTACT
your nearest authorized Multiquip dealer for
instructions or servicing.
NEVER! operate the roller on side
slopes. The roller may tip over
causing injury to personnel and
severe damage to the equipment
Figure 4. Recommended Slope
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — VIBRATORY ROLLER COMPONENTS
Figure 6. MDR-9GH
Compo
Figure 6 illustrates the location of the major components
for the MDR-9GH Vibratory Roller. The function of each
component is described below:
7. Engine – This vibratory roller uses a HONDA
GX340KQAE2 gasoline engine. Refer to the owner’s
manual for engine information and related topics.
1. Handle Bar – When operating the roller, this handle is to
be in the downward position. When the roller is to be
stored, move the handle bar to the upright position.
8.
Vibrator Lever (on the body of machine) – Turns the
vibration on and off.
9. Water Tank – Holds 6 gallons (23 liters) of water for the
2. Hand Grip – When operating the roller, use this hand grip
to maneuver the roller. Also has dead man device, when
pressed or hit while traveling in reverse, causes the travel
lever to return to neutral position to stop the machine.
sprinkler system.
10. Shock Absorber -
11. Scraper Bar – This bar helps prevent buildup of material
between the drum and the frame.
3. Travel Lever – Push the lever forward, the roller will move
in a forward direction, pull the lever backwards, the roller
will move in backwards direction. Placing the lever in the
middle (midway) will cause the roller not to move (neutral).
12. Vibration Rollers – 18-inch diameter steel drums that
provide the compaction force in the compaction and
patching of asphalt-type surfaces.
13. Checking Cover for Chains –Take off the cover to check
4.
5.
Vibrator Lever – Turns the vibration on and off.
and lubricate chains.
Oil Cap – Open to fill with proper grade of diesel engine
oil.
14. WaterValves–Turn on the water sprinkling system.
15. Hydraulic Oil Gauge – Indicates the hydraulic oil level.
6. V-Belt Cover – Remove this cover to gain access to theV-
belts.NEVER run the vibratory roller without theV-belt cover.
If the V-belt cover is not installed, the possibility exist that
your hand may get caught between the V-belt and clutch,
thus causing serious injury and bodily harm.
PAGE 16 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — ENGINE COMPONENTS
Figure 7. HONDA GX340KQAE2 Engine Components
6. Choke Lever – Used in the starting of a cold engine, or in
cold weather conditions. The choke enriches the fuel
mixture.
INITIAL SERVICING
The engine (Figure 7) must be checked for proper lubrication and
filled with fuel prior to operation. Refer to the manufacturers engine
manual for instructions & details of operation and servicing. The
engine shown above is a HONDA engine, operation for other
types of engines may vary somewhat.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
1.
Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Operating the engine without an
air filter, with a damaged air filter,
or a filter in need of replacement
DANGER
will allow dirt to enter the engine,
causing rapid engine wear.
Adding fuel to the tank should be done only when
the engine is stopped and has had an opportunity to
cool down. In the event of a fuel spill, DO NOT
8. Spark Plug – Provides spark to the ignition system. Set
spark plug gap to 0.6 - 0.7 mm (0.028 - 0.031 inch) Clean
spark plug once a week.
attempt to start the engine until the fuel residue has been completely
wiped up, and the area surrounding the engine is dry.
9. Muffler – Used to reduce noise and emissions.
2. Throttle Lever – Used to adjust engine RPM speed (lever
advanced forward SLOW, lever back toward operator
FAST).
WARNING
3. Engine ON/OFF Switch – ON position permits engine
Engine components can generate extreme heat.
To prevent burns, DO NOT touch these areas
while the engine is running or immediately after operating. NEVER
operate the engine with the muffler removed.
starting, OFF position stops engine operations.
4. Recoil Starter (pull rope) – Manual-starting method. Pull
the starter grip until resistance is felt, then pull briskly and
smoothly.
10. Fuel Tank – Holds unleaded gasoline. For additional
5. FuelValve Lever – OPEN to let fuel flow, CLOSE to stop
information refer to engine owner's manual.
the flow of fuel.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — INSPECTION
3. If the oil level is low, fill to the edge of the oil filler
hole with the recommended oil type (Table 4).
Maximum oil capacity is 1.6 quarts (1.1 liters).
CAUTION :
Never operate the vibratory
roller in a confined area or
enclosed structure that
does not provide ample
free flow of air.
TABLE 4. OIL TYPE
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
ALWAYS wear approved eye and hearing
protection before operating the vibratory roller.
BEFORE STARTING
0°C or Lower
1.
Read safety instructions at the beginning
of manual.
2.
Familiarize yourself with the operating
and control elements of the machine and
Explosive Fuel
the working environment. This includes obstacles in the
working area, bearing capacity of the ground and the
necessary safety provisions.
DANGER
Dieselfuelishighlyflammableandcanbedanger-
ousifmishandled.DONOTsmokewhilerefueling.
DO NOT attempt to refuel the vibratory roller if the
engine is hot! or running.
3. Checktheairfilterfordirtanddust.Iftheairfilterisdirty, replace
air filter with a new one as required.
4.
5.
6.
Check fastening nuts and bolts for tightness. Loose threads
may cause damage to the machine when vibrating.
CHECKING FUEL
Understand the geographical features and regulations of
the job site.
1. Remove the fuel cap located on top of fuel tank.
2. Visuallyinspecttoseeiffuellevelislow. Iffuelislow,replenish
with diesel fuel (Figure 9).
Clean the vibratory roller, removing dirt and dust,
particularly, the bottom of the plate, engine cooling air inlet.
3. When refueling, be sure to use a strainer for filtration. DO
CHECKING ENGINE OIL LEVEL
NOT top-off fuel. Wipe up any spilled fuel.
1. Make sure that the machine is situated in a flat
surface so that level measurements will be accurate.
2. Pull out the dipstick from the oil tank (Figure 8).
CAUTION :
DO NOT overfill oil tank. This could cause oil
leaks and sluggish operation. Clean cap and
surrounding area before opening to prevent dirt
from entering tank.
Figure 9. Refueling
DANGER
Fuel spillage on a hot engine can case a fire or
explosion. If fuel spillage occurs, wipe up the
spilled fuel completely to prevent fire hazards.
NEVER! smoke around or near the roller.
Figure 8. Oil Dipstick
PAGE 18 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — INSPECTION
CHECKINGTHE CLUTCH BOX OIL LEVEL
CHECKING HYDRAULIC SYSTEM
1.
2.
3.
Check clutch box for any oil leakage.
1. Check the oil tank level gauge (Figure 10). Oil level
should be at the middle indication of the gauge or
higher. Fill as required
Remove the level plug and check oil level (Figure 12).
Add oil if necessary.
2. Check the surroundings of the oil tank, hydraulic
pump and motor for oil leakage.
Figure 12. Clutch Box Oil Level Check
Figure 10. Hydraulic System Oil Level Gauge
CHECKINGTHEVIBRATOR OIL LEVEL
DANGER
1.
Remove the red filler plug and the oil level inspection hole
plug from the vibrator case (Figure 13).
ALWAYS keep hands and fingers away from
pinch points. DO NOT allow anyone to reach in
on dangerous sections of the machine to avoid
any accidents.
2.
Fill with oil until oil overflows from inspection hole.
CHECKING THE V-BELT
1. Check all bolts and screws and make sure all are
securely tightened.
2. Check V-belt for proper tension. The normal slack
should be approximately 1/8 inch (3 to 5 mm) when
the belts are forcibly depressed between the two
sheaves (Figure 11). Insufficient tension causes
weak vibration and machine damage.
Figure 13. Vibrator Oil Level Check
Figure 11. V-BeltTension
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — INSPECTION/START-UP
POSITIONINGTHE HANDLE BAR
CHECKINGWATERTANK
1.
Release the handle bar release pin (Figure 15) and position
the handle bar to the lowered position before starting
operation.
1.
Check the water tank to see if filled. Add water if necessary.
The water tank has a capacity of approximately 6 gallons
(23 liters) (Figure 14).
2.
When machine is not in use, release the handle bar release
pin and position the handle bar to the upright position.
Figure 14. Water Tank Check
CAUTION :
Be careful not to confuse the water tank with the
oil tank.
Handle Bar
Release Pin
Figure 15. Handle Bar Positioning
CHECKING LEVERS
INITIAL STARTUP (ENGINE)
Recoil Start
1.
Check travel and vibrator levers to make sure they are
functioning properly (Figure 6).
2.
With travel lever placed in reverse, push the deadman
device and verify that the travel lever returns to neutral
position.The travel lever stays in neutral position once the
deadman device is released.
1
Place the fuel valve lever (Figure 16) to the "ON" position.
CHECKING SCRAPER BAR
1.
Check scraper bar and make sure that they are not clogged
with mud, bent or damaged (Figure 6).
2.
Adjust clearance between drums and scrapers as
necessary.
CHECKING BOLTS, NUTS, AND SCREWS
1.
Check bolts, nuts, and screws on various parts of the
machine, including the engine, for proper tightness.
Figure 16. Engine Fuel Valve Lever
PAGE 20 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — START-UP
4. Rotate the throttle lever (Figure 19) halfway betweenfast
andslowforstarting. Theenginegovernorspeedisfactory
set to ensure optimum operating speeds.
2. Place the Engine ON/OFF switch (Figure 17) in the "ON"
position.
Figure 17. Engine ON/OFF Switch
Figure 19. Throttle Lever
5. Grasp the starter grip (Figure 20) and slowly pull it out.The
resistancebecomesthehardestatacertainposition,corre-
spondingtothecompressionpoint.Pullthestartergripbriskly
andsmoothlyforstarting.
The CLOSED position of the choke
lever enriches the fuel mixture for
starting a COLD engine. The OPEN
position provides the correct fuel
mixture for normal operation after
starting, and for restarting a warm
engine.
NOTE
3. Place the Choke Lever (Figure 18) in the "CLOSED "
position.
Figure 20. Starter Grip
CAUTION
DO NOT pull the starter rope all the way to the
end. DO NOT release the starter rope after
pulling. Allow it to rewind as soon as possible.
Electric Start
Figure 18. Choke Lever
1. Turnthekeytothe"START"positionuntiltheenginestarts.
Iftheenginefailstostartwithin5seconds,releasethekey,and
wait at least 10 seconds before operating the starter again.
CAUTION
The engine speed has been
set at the factory. Changing the
governor speed could damage
the vibratory roller.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — OPERATION
TRAVELING
VIBRATING
CAUTION :
1. Shift the two vibrator levers (Figures 22 and 23) to the
vibrate position to start vibrations.
Make suretofollowallsafetyrulesreferenced
in the safety section of this manual before
operating roller. Keep work area clear of
debris and other objects that could cause
damage to the roller or bodily injury.
1. To make the roller move in the forward direction push the
travel lever ( Figure 21) forward.This roller has a hydraulic
variable speed transmission. By moving the travel lever
varioysincrements,youcanvarythespeedfrom0to1.8mph
(0 to 3 km/hr).
Figure 22. Vibrator Lever
Figure 21.Travel Lever
2. Tomaketherollermoveinthereversedirectionpullthetravel
lever ( Figure 21) backwards.
Figure 23. Vibrator Lever (Body)
CAUTION :
3. Firmlygasptheroller'shandgrip,therollerwillbeginmoving
in the desired position when the direction lever has been
placed in the desired position.
Using vibration with clutch slipping
causes the clutch to burn. Also, vibration
should NOT be used over completely
compacted area, paved road surface, or
with stationary roller.
CAUTION :
DO NOT reduce speed during work.
When shifting travel lever from forward
to reverse, be sure to stop the lever at
the neutral position first before moving
the lever to the opposite direction. DO
NOT shift the lever from forward to
reverse (or reverse to forward) in one
motion.
WATERING
1. To operate water sprinkling system, turn on the front and
rear water valves on the side of the roller.(Figure 24).
CAUTION :
After test travel, shut down engine and
check for any problems including oil
leakage. If any trouble is found, correct
the problem before attempting to operate
the roller again.
Figure 24.WaterValves
PAGE 22 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — OPERATION/LIFTING/TRANSPORTING
LIFTING
STOPPING
1.
2.
3.
4.
5.
Use a crane or lift to load and unload the machine. A
skilled crane operator is required to perform the job.
1. Place the vibrator and travel levers to the neutral position.
2. Slow down the engine and allow to cool for at least 2
minutes. In an electric start, return the key switch to
the STOP position as soon as the engine stops.
When lifting the machine, check for any damaged or
loose bolts, lifting hooks, and shock mounts.
Check any damaged or loose bolts in the guard frame to
avoid machine sliding off.
CAUTION :
Neglecting to return the key switch to the
STOP position will cause the battery to
discharge, making start-up impossible the
next time.
Make sure that the machine is shut off before machine is
lifted.
Use reliable cable for lifting.
6. Always lift the machine vertically and keep the
machine away from workers and animals.
3. After the engine stops, close the fuel cock.
7.
Do not lift the machine higher than the required
height.
4. The hydraulic brake is automatically engaged when the
travel lever is in neutral position.When parked on a slope
with the engine turned off, place a block against the
roller drum to prevent the roller from moving.
UNLOADING
TRANSPORTING
1. Always make sure that the machine is shut off while
being transported.
1.
If you need to move the roller by pushing it manually
once engine is stopped, push in the upper and lower
knobs of the transmission check valve. This will
cause the hydraulic break to disengage and allow
the roller to be moved without causing damage
(Figure 25).
2. Check that the fuel cap is properly closed and
tightened.
3. When traveling long distances or on rugged terrain,
drain the fuel of the machine before transporting.
4. Tie down the machine securely on the
transportation so that it will not move or topple over.
Figure 25. Disengaging Hydraulic Brake
2. After moving, reset upper and lower knobs.
CAUTION :
NEVER tow roller with any type of vehicle.
Doing so will damage the hydraulic
system.
NEVER perform unloading procedure on
a slope. This may cause roller to roll down
if parking brake or blocking is deficient.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — MAINTENANCE
CAUTION:
CAUTION:
Fuel piping and connections should be replaced
every 2 years.
Inspection and other services should always be
carried out on hard and level ground with the
engine shutdown.
INSPECTION AND MAINTENANCE SERVICETABLES
TABLE 6. MDR-9GH ENGINE CHECK
1. To make sure your plate vibratory roller is always in good
working condition before using, carry out the maintenance
inspection in accordance with Tables 4 through 6.
ITEM
HOURS OF OPERATION
Oil or Fuel Leak
Every 8 hours (every day)
Every 8 hours (every day)
TABLE 5. MDR-9GH MACHINE INSPECTION
Tightness of Fastening
Threads
HOURS OF
ITEM
REMARKS
OPERATION
Every 8 hours (every day)
(Replenish to specified maximum
level)
Engine Oil Check and
Replenishment
Loose or Missing
Screws
Every 8 hours
(every day)
Every 8 hours
(every day)
After first 25 hours then every 50 to
100 hours
Damaged Parts
Engine Oil Replacement
Air Filter Cleaning
Function of Controlling
System Part
Every 8 hours
(every day)
Every 100 hours
See separate engine manual for details on engine check.
Chain Tension
Adjustment
Every 50 hours
See page 26
See page 28
Initially after 25
hours, then every
250 hours (2
months), every
500 hours (4
months), every
1,000 hours
DAILY SERVICE
z
Check for leakage of fuel or oil.
z
Check for loose screws including tightness. See Table 6
below (tightening torque ), for retightening:
Hydraulic Oil Filter
Replacement
thereafter.
TABLE 7. TIGHTENING TORQUE (in. kg/cm) DIAMETER
Initially, every 4 to
5 hours. After one
week, twice a day.
After 2 weeks,
Material 6mm 8mm 10mm 12mm 14mm 16mm 18mm
20mm
2,000
3,800
5,600
Hydraulic Oil Check
See page 27
4T
70
150
250
400
300
500
800
500
800
750
1,100
2,000
2,900
1,400
2,700
4,200
6-8T
11T
100
150
1,300
2,000
once a day.
1,200
Hydraulic Oil
Replacement
Every 1,000 to
1,500 hours
See page 27
See page 27
300~ 650 ~
350 700
*
100
* (In case counter-part is of aluminum)
(Threads in use with this machine are all right handed)
Material and quality of material is marked on each bolt, and screw.
Vibration Clutch Check
As necessary
CAUTION:
z
Remove soil and clean the bottom of roller.
These inspection intervals are for operation
under normal conditions. Adjust your inspection
intervals based on the number hours vibratory
roller is in use, and particular working conditions.
z
z
Check the levers, cables and linkage.
Check engine oil.
PAGE 24 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — MAINTENANCE
SPARK PLUG
AIR FILTER
1. Remove and clean the spark plug (Figure 26).
1. Remove the air cleaner cover and foam filter element as
shown in Figure 28.
2. Adjust the spark gap to 0.028 ~0.031 inch (0.6~0.7 mm).This
unit has electronic ignition, which requires no adjustments.
2. Tap the paper filter element (Figure 28) several times on a
hard surface to remove dirt, or blow compressed air [not
exceeding 30 psi (207 kPa, 2.1 kgf/cm2)] through the filter
elementfromtheaircleanercaseside.NEVER brushoffdirt.
Brushingwillforcedirtintothefibers.Replacethepaperfilter
element if it is excessively dirty.
3. Cleanfoamelementinwarm,soapywaterornonflammable
solvent. Rinseanddrythoroughly. Diptheelementinclean
engineoilandcompletelysqueezeouttheexcessoilfromthe
element before installing.
Figure 26. Spark Plug Gap
ENGINE OIL REPLACEMENT
1. Replace engine oil, first in 25 hours of operation and every
50 to 100 hours afterwards.
2. Drain the engine oil when the oil is warm as shown in
Figure 27.
3. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
4. Replace engine oil with recommended type oil as listed
in Table 3. Engine oil capacity is 1.16 quarts (1.1 liters).
DO NOT overfill.
5. Install drain bolt with sealing washer and tighten se-
curely.
Figure 28. Engine Air Filter
Figure 27. Engine Oil (Draining)
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — MAINTENANCE
CAUTION:
CHECKINGTHE CHAINS
1. Take off the checking cover on roller and coat grease on the
chain if necessary (Figure 29).The chain should be lightly
lubricated with motor oil.
NEVERattempttochecktheV-beltwiththeengine
running.Severeinjurycan occurifyourhandgets
caughtbetweentheV-beltandtheclutch(Figure
31).Alwaysusesafetygloves.
CLUTCH
PULLEY
VIBRATOR
PULLEY
Figure 31. V-Belt Hazard
VIBRATION CLUTCH ADJUSTMENT
Figure 29. Chain Cover
1. Remove the protective cover from the clutch by removing
the 4 allen screws.
2. Check the chain tension and if loose, adjust the chain tension
with the tightener (Figure 30. Chain tension should be
adjusted every 50 hours of operation.
2. Pull out the stop key and turn to the release position
(Figure 30).
3. Viewing the clutch from the shifter-pulley side: if the clutch
nut is turned to the right, the clearance between the adjusting
and pressure plate decreases as the amount of torque
increases. Normal adjustment is from 1 to 2 notches.
4. Make sure that the shifting lever is not too stiff. Lever should
engage with moderate pressure.
5. After adjustment, return the stop key to the locked position.
Figure 30. ChainTightener
PAGE 26 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — MAINTENANCE
HYDRAULIC OIL CHECK
HYDRAULIC OIL FILTER CHECK
1. Check for any oil leakage from the hoses and joints daily.
1. The hydraulic oil filter should be replaced after first 25 hours
of operation.
2. Check hydraulic oil level every 4 to 5 hours after starting
operation.
2. After first replacement, it should be replaced after 250 hours
operation (2 months), every 500 hours of operation
(4 months), and every 1,000 hours of operation thereafter.
3. After one week of operation, check hydraulic level twice a
day .
3. When the suction resistance exceeds 254 mmHg
(oil temperature in operation is 140 degrees F), replace
filter.
4. After two weeks of operation, check hydraulic level once a
day .
5. Replace hydraulic oil after first 200 hours and in every 1,000
hours of operation.
4. To remove the oil filter, wind a cloth around the filter to prevent
slipping (Figure 33).
CAUTION:
5. Tie a rope securely around the filter (Figure 33).
Make sure hydraulic oil is at a normal safe
operating level.DO NOT over fill.
REPLACING HYDRAULIC OIL
1. Change the hydraulic oil every 1,000 to 1,500 hours of
operation. Change the hydraulic oil more often in high
ambient temperature operation.
2. Remove the drain plug and hose tank and drain the hydraulic
oil.
3. Reinstall the drain plug to the oil tank.
4. Open the tank cap (Figure 32) and fill tank with hydraulic oil.
(Capacity: About 4.5 gallons). Use ShellTellus Oil #46 or
equivalent.
Figure 33. Cloth and Rope Around Filter
6. Forcibly pull the rope to remove the filter (Figure 34).
Figure 34. Filter Removal
Figure 32. Hydraulic Oil Change
7. Immediately replace with new filter, screwing it on by hand
to avoid hydraulic oil leak.
5. After filling tank, tighten the tank cap firmly with a wrench.
CAUTION:
Use only genuine Mikasa
NOTE
replacement oil filters (10
micron filter paper. Do not use
automobile-type oil filters.
Make sure that dust , water, and other foreign
objects do not enter tank. It is recommended
to filter the oil through a cloth.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — MAINTENANCE
HDRAULIC AIR EXTRACTION
1. After filling hydraulic oil tank with oil, loosen the oil hose
joint and check that oil is enough to reach the oil suction
and outlet ports in the hydraulic transmission.Tighten the
hose joint securely after checking.
2. Loosen the charge relief valve located on the front side of
the hydraulic transmission (Figure 35).
Figure 36. Unscrewing Right Lock Nut
Figure 35. Loosening Charge ReliefValve
3. Check that oil flows out from the valve hole.
4. Replace the charge relief valve tightly.
5. With the travel and vibrator levers in neutral position, start
the engine and idle at low speed for 3 to 5 minutes.
Figure 37. Unscrewing Left Lock Nut
6. Check the forward and reverse rotation of the output shaft
by moving the travel lever slowly to its forward and reverse
positions.
3. If the machine moves forward, screw the turn-buckle
clockwise. If the machine moves backwards, screw the turn-
buckle counterclockwise (Figure 38).
7. Check the oil level gauge and make sure that there are no
air bubbles mixed in the oil. After checking, operate the roller
slowly at first then at full speed.
4. Screw back the lock nuts on the turn-buckle.
5. Start the engine and make sure that the roller does not inch
forward or backward at the neutral position of the travel
lever.
8. When oil level in the tank is low, replenish oil up to the
specified level, and screw the cap securely with a wrench.
9. If bubbles remain in the oil or foam is found, air is being
sucked through the suction side and should be checked.
NEUTRAL POSITION ADJUSTMENT
Once the travel lever has veen set to neutral position with the
engine running, the hydraulic brake is is operating and the roller
should not move. If the roller inches forward or backwards with
the lever in the neutral position, turn-buckle of the cable should
be adjusted as follows:
1. Stop the engine and set the travel lever in the neutral
position.
Figure 38. Adjusting theTurn-Buckle
2. Unscrew the two lock nuts on the sides of the cable
(Figures 36 and 37).
PAGE 28 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — MAINTENANCE
If the neutral position of the travel lever and the neutral point of
transmission do not match after adjustment is repeated, align as
follows:
z
z
z
DO NOT close the exhaust outlet of battery.The gas pressure
building up in the battery may cause explosion.
Before using a battery charger, read and understand the
charger instruction manual thoroughly.
1. Loosen the hex socket head bolt M10 used for mounting the
control lever on the underside of the transmission
(Figure 39).
Charge the battery in a non-spark, well-ventilated area. Avoid
fire from cigarette sparks or matches.
2. For forward movement, move the control lever slightly to the
left.
1. If a battery has not been used for some time, reduce
the charge level initially to protect each plate inside
the battery.
3. For backwards movement, move the control lever slightly to
the right.
2. Check the battery terminals periodically to ensure
that they are in good condition.
3. Use wire brush or sand paper to clean the battery
terminals.
4. Check battery for cracks or any other damage. If white
pattern appears inside the battery or paste has
accumulated at the bottom, replace the battery.
5. Measure the specific gravity of electrolyte:
z
z
completely charged: 1.270 - 1.290
needs charging: 1.260 or lower
Figure 39. Unscrewing Left Lock Nut
BATTERY MAINTENANCE
DANGER :
6. If the machine will not be in operation for a long
period of time, charge the battery sufficiently, tighten
all caps, correctly, store in cool dry place and check
the battery charge level every month to maintain the
performance of the battery.
Lead-acid battery contains
sulfuric acid, which may damage
eyes or skin on contact.
BATTERY CABLE CONNECTION
1.
When removing cable, disconnect the ground side (normally
negative) first (Figure 40).
Negative
Terminal
FORYOUR SAFETY:
z
ALWAYS wear a face shield to avoid acid getting into the
eyes. If acid gets in contact with eyes, flush immediately with
clean water and get medical advice.
z
Wear rubber gloves and protective clothes to keep acid off
skin. If acid gets in contact with skin, wash off immediately
with clean water.
Positive
z
z
Use a flashlight to check battery electrolyte level.ALWAYS
check the engine is stopped.
Terminal
Figure 40. Battery Connection
DO NOT charge battery or jump-start engine when the
battery is frozen. Warm the battery to 15 degrees F or battery
may explode.
2.
When installing cable connect the ground side (normally
negative) last.
z
Replace the battery with the same or similar capacity battery
or battery may explode.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — ENGINETROUBLESHOOTING
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a breakdown,
please take a remedial action following the diagnosis based on the Engine Troubleshooting (Table 8) information shown
below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult our
company's business office or service plant.
TABLE 8. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or replace
spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
ON/OFF switch is shorted?
Ignition coil defective?
Set to proper gap.
Check switch wiring, replace
switch.
Replace ignition coil.
Set correct spark gap and clean
points.
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Improper spark gap, points dirtry?
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Difficult to start, "fuel is available, spark
is present and compression is normal"
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Clean or replace air cleaner.
Re-seat valves.
Suction/exhaust valve stuck or protruded?
Replace piston rings and or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low"
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and spark plug
gaskets.
Fuel not available in fuel tank?
Fill with correct type of fuel.
Apply lubricant to loosen fuel
cock lever, replace if necessary.
Fuel cock does not open properly?
No fuel present at carburetor.
Fuel filter clogged?
Replace fuel filter.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
PAGE 30 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — ENGINETROUBLESHOOTING
TABLE 8. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Air cleaner not clean?
Clean or replace air cleaner
Check float adjustment, re-build
carbureator.
Improper level in carburetor?
"Weak in power" compression is proper
and does not misfire.
Defective Spark plug?
Defective Spark plug?
Clean or replace spark plug.
Flush fuel system, and replace
with correct type of fuel.
Water in fuel system?
"Weak in power" compression is proper
but misfires.
Dirty spark plug?
Clean or replace spark plug.
Replace ignition coil.
Ignition coil defective?
Replace with correct type of
spark plug.
Spark plug heat value improper?
Engine overheats.
Correct type of fuel?
Replace with correct type of fuel
Clean cooling fins.
Cooling fins dirty?
Governor adjusted correctly?
Governor spring defective?
Adjust governor.
Replace governor spring.
Rotational speed fluctuates.
Recoil starter malfunction.
Check entire fuel system for leaks
or clogs.
Fuel flow restricted?
Recoil mechanism clogged with dust and Clean recoil assembly with soap
dirt?
and water.
Sprial spring loose?
Replace sprial spring.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — ROLLERTROUBLESHOOTING
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, please take a remedial action following the diagnosis based on the RollerTroubleshooting (Table 9) information
shown below and on the proceeding page. If the problem cannot be remedied, please leave the unit just as it is and consult
our company's business office or service plant.
TABLE 9. ROLLER TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
Defective centrifugal clutch?
SOLUTION
Repair or replace clutch.
Damaged rubber coupling and flange?
Defective travel cable and link?
Replace rubber coupling and flange.
Repair or replacetravel cable and link.
Damaged scraper or too much mud in scraper? Replace or repair scraper.
Damaged or clogged oil filter?
Damaged or leaking hydraulic pipe?
Low oil level or contaminated oil?
Damaged or leaking hydraulic transmission?
Damaged or leaking hydraulic transmission?
Damaged drum gear and bearing?
Bad drum rotation?
Replace filter.
Unit does not travel or
travel is not smooth.
Repair or replace parts.
Replenish or replace oil.
Repair or replace hydraulic pump.
Repair or replace hydraulic motor.
Repair parts.
Repair or replace drum.
Repair or replace clutch.
Replace V-belt or adjust tension.
Defective centrifugal clutch?
Damaged or slipping V-belt?
Replace or repair vibration cable and
linkage.
Damaged vibration cable and linkage?
Unit does not vibrate or
has weak vibration.
Damaged vibration clutch?
Adjust or replace clutch.
Replace V-belt.
Defective clutch vibrator pulley V-belt?
Check and repair vibrator. Check if oil
level is not excessively high.
Vibrator does not turn smoothly with hand?
PAGE 32 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
How to read the marks and remarks used in this parts
book.
If more than one of the
same reference number
is listed, the last one
listed indicates newest
(or latest) part available.
Items Found In the “Remarks” Column
Serial Numbers-Where indicated, this indicates a serial number
range (inclusive) where a particular part is used.
Model Number-Where indicated, this shows that the
corresponding part is utilized only with this specific model number
or model number variant.
Items Found In the “Items Number” Column
All parts with same symbol in the number column, , #, +, %,
*
or <, belong to the same assembly or kit
The contents of this
parts catalog are
subject to change
without notice.
PAGE 34 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
SUGGESTED SPARE PARTS
MQ MIKASA MDR-9GH VIBRATORY WALK-BEHIND
ROLLER W/HONDA GX340QAE2 GASOLINE ENGINE
1 to 3 Units
Qty.
P/N
Description
1 .......... 0750800671 ......... CHAIN DRIVE
3 .......... 501010440 ........... OIL FILTER, HYDRAULIC
6 .......... 070100360 ........... V-BELT, A-36 VIBRATION
2 .......... 502303040 ........... THROTTLE WIRE
6 .......... 17210ZE3505 ....... ELEMENT AIR CLEANER
3 .......... 35111880003 ....... KEY, IGNITION
6 .......... 9807956846 ......... SPARK PLUG
1 .......... 28462ZV7003 ....... STARTER ROPE
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — DECAL PLACEMENT
DECAL PLACEMENT
PAGE 36 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — DECAL PLACEMENT
DECAL PLACEMENT
NO.
1
PART NO.
920200591
920200630
920201590
920101510
920203290
920200450
920101290
920201100
920200320
920200440
920200470
920101480
920101280
920101200
PART NAME
QTY. REMARKS
PLATE, CAUTION
1
1
1
1
1
1
2
2
1
1
1
1
1
1
2
PLATE, SERIAL NO.
DECAL, MQ MARK 98X70
DECAL, MIKASA MARK 440MM
DECAL, CAUTION
DECAL, OIL FILTER
DECAL, VIBRATION
DECAL, CLUTCH LEVER
DECAL, WATERTANK
DECAL, PROHIBIT TOW
DECAL, OIL TANK
3
4
5
6
7
8
9
10
11
12
13
14
DECAL, OIL LEVEL
DECAL, FORWARD & REVERSE
DECAL, GREASE
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — BODY ASSY.
BODY ASSY.
PAGE 38 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — BODY ASSY.
BODY ASSY.
NO.
1
2
3
4
5
6
8
9
10
42
43
44
45
46
48
49
51
52
53
54
55
56
57
58
59
60
68
69
82
83
PART NO.
PART NAME
QTY. REMARKS
502101270
502100720
502100710
502200960
001211430
030214350
930407021
020312100
030212300
502201150
502201160
502402930
502402940
001221025
030210250
501010150
502302511
001221030
030210250
502424050
001220825
030208200
952401560
031110160
502200990
001521225
502403940
001521020
020310080
030210250
BASE
1
1
1
2
8
8
4
8
8
1
1
1
1
6
6
4
2
8
8
2
6
6
6
8
1
18
2
4
4
4
SIDE PLATE, RIGHT
SIDE PLATE, LEFT
RUBBER PLATE
BOLT 14X30 H
LOCKWASHER M14
SHOCK ABSORBER MED-70/MS
NUT M12
LOCKWASHER M12
SPRINKLING PIPE, FRONT
SPRINKLING PIPE, REAR
VINYL PIPE 10X13X280
VINYL PIPE 10X13X950
BOLT 10X25 T
LOCKWASHER M10
CAP 1/4
SCRAPER, END
BOLT 10X30 T
LOCKWASHER M10
SCRAPER/CENTER
BOLT 8X25 T
LOCK WASHER M8
WASHER 8.5X20X3
FLAT WASHER M10
BASE, SCRAPER
SOCKET HEAD BOLT 12X25 T
CHAIN COVER
SOCKET HEAD BOLT 10X20 T
NUT M10
LOCKWASHER M10
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — FRONT COVER ASSY.
FRONT COVER ASSY.
PAGE 40 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — FRONT COVER ASSY.
FRONT COVER ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
13
14
16
17
18
20
21
22
23
24
25
26
27
28
31
32
33
34
35
36
37
38
39
031110160
502103800
001220820
030208200
952401560
502302490
001220815
030208200
031108160
502302500
001221020
030210250
021110160
001220825
502215470
001221020
030210250
031110160
001221015
030210250
031110160
502010650
407310670
FLAT WASHER M10
FRONT COVER
4
1
4
7
7
1
4
4
4
1
1
1
1
3
1
2
2
2
2
2
2
2
1
BOLT 8X20 T
LOCK WASHER M8
WASHER 8.5X20X3
CHECK COVER
BOLT 8X15 T
LOCK WASHER M8
FLAT WASHER M8
SUPPORT/COVER
BOLT 10X20 T
LOCKWASHER M10
FLAT WASHER M10
BOLT 8X25 T
BELT COVER
BOLT 10X20 T
LOCKWASHER M10
FLAT WASHER M10
BOLT 10X15 T
LOCKWASHER M10
FLAT WASHER M10
ELBOW 90 DEG. 1/4
TANK CAP D108-120, RUBBER
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — FRONT COVER ASSY. (CONTINUED)
FRONT COVER ASSY.
PAGE 42 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — FRONT COVER ASSY. (CONTINUED)
FRONT COVER ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
41
65
66
81
82
83
88
89
90
91
92
93
94
95
96
97
954403241
001801050
020310080
001211030
020310080
030210250
920200591
920200630
920201590
920101510
920203290
920206450
920200450
920101290
920201100
920200320
920200440
959402990
091005020
020305040
030205130
031105080
025203020
959403251
502420150
001200820
030208200
031108160
COCK PT 1/4, BH-1211 (AL)
BOLT 10X50 WHOLETHREAD
NUT M10
BOLT 10X30 H
NUT M10
2
1
4
4
4
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
2
1
2
2
2
LOCKWASHER M10
PLATE, CAUTION
PLATE, SERIAL NO.
DECAL, MQ MARK 98X70
DECAL, MIKASA MARK 440MM
DECAL, CAUTION
PLATE, MADE IN JAPAN
DECAL, OIL FILTER
DECAL, VIBRATION
DECAL, (CLUTCH LEVER)
DECAL, WATERTANK
DECAL, PROHIBIT TOW
ROPE
SCREW 5X20
NUT M5
LOCK WASHER M5
FLAT WASHER M5
SPLIT COTTER PIN 3X20
PLATE SPRING
98
100
101
102
103
104
105
106
107
108
109
110
SPACER
BOLT 8X20
LOCK WASHER M8
FLAT WASHER M8
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — AXLE ASSY.
AXLE ASSY.
PAGE 44 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — AXLE ASSY.
AXLE ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1
502101570
502202290
044006309
952400940
502302420
060406010
001521025
502200930
502302430
001521240
502200940
502200950
020130240
030230750
502302440
001521040
502303370
502338050
044006370
047910050
952401240
952406190
502302460
060305010
001520820
502402720
951400090
020118150
030218460
952400950
502305360
502303590
001521235
001521240
502402740
001210820
030208200
502403090
075080061
502402920
DRUM
2
2
2
ROLLER SHAFT
3
BEARING 6309VV
SPACER 45605
4
4
4
5
BEARING COVER
OIL SEALTC-689012
SOCKET HEAD BOLT 10X25 T
BRACKET/L
2
6
4
7
12
2
8
9
SPACER
2
10
11
12
13
14
15
16
17
17
18
19
20
20
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
SOCKET HEAD BOLT 12X40 T
BRACKET/R FRONT
BRACKET/R REAR
NUT M30, P2.0
12
1
1
4
LOCKWASHER M30
GEAR 57
SOCKET HEAD BOLT 10X40 T
GEAR SHAFT
GEAR SHAFT
BEARING 6307VV
ROLLER BEARING NF307W
SPACER 35453
SPACER 35X45X3 S
COVER/GEAR SHAFT
OIL SEAL TB-55729
SOCKET HEAD BOLT 8X20 T
SPROCKET 15
KEY 10X8X33
NUT M18, P1.5
LOCKWASHER M18
WASHER 19456
BLOCK
CYLINDER BLOCK
SOCKET HEAD BOLT 12X35 T
SOCKET HEAD BOLT 12X40 T
BRACKET COVER
BOLT 8X20 H
4
2
12
2
2
2
2
2
2
2
2
8
2
2
2
2
2
2
2
30
30
2
12
12
2
1
1
LOCK WASHER M8
BEARING HOLDER
CHAIN RS80-61
TIGHTENER
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — AXLE ASSY. (CONTINUED)
AXLE ASSY.
PAGE 46 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — AXLE ASSY. (CONTINUED)
AXLE ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
40
41
42
43
44
45
46
47
48
49
50
51
52
54
55
61
502302480
044006205
080100520
001210820
030208200
952400130
502402750
001521230
502402760
502402770
502402780
952401330
060604030
042006309
502408150
351010050
TIGHTENER PLATE (SHAFT)
BEARING 6205VV
1
2
1
1
1
1
1
3
2
2
2
2
2
4
4
2
STOP RING R-52
BOLT 8X20 H
LOCK WASHER M8
WASHER 9304
TIGHTENER PLATE HOLDER
SOCKET HEAD BOLT 12X30 T
FELT SEAL 6X8X1350
FELT SEAL 6X8X188
FELT SEAL 5X6X217
COLLAR 72803
OIL SEAL VC-45686
BEARING 6309ZZ
FELT RING 901027/BRACKET
GREASE FITTING A-MT6X1
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH —TRANSMISSION ASSY.
TRANSMISSION ASSY.
PAGE 48 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH —TRANSMISSION ASSY.
TRANSMISSION ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1
2
3
4
5
6
7
8
502010530
502010540
501010410
001520620
031106100
501010420
501010430
501010440
501010450
030210250
020310080
501010460
951400100
952400130
001210820
030208200
502303350
502010570
501010500
951400110
952400170
020118150
030218460
042006207
042006306
080200350
060303030
501010520
001220825
030208200
001211025
030210250
502302530
080100160
502010590
502321570
515447020
099208012
502402800
001521025
GEAR CASE
COVER, GEAR CASE
1
1
PACKING, GEAR CASE COVER
SOCKET HEAD BOLT 6X20 T
FLAT WASHER M6
SET BOLT, 87L-M12-M10
TRANSMISSION 1515-522
OIL FILTER
PACKING/TRANSMISSION
LOCKWASHER M10
NUT M10
PINION 15
KEY 5X5X35
WASHER 9304
BOLT 8X20 H
LOCK WASHER M8
GEAR 80
DRIVE SHAFT
SPROKET 9
KEY 7X7X35
WASHER 19454
NUT M18, P1.5
LOCKWASHER M18
BEARING 6207ZZ
BEARING 6306ZZ
STOP RING S-35
OIL SEAL TB-30428
BEARING COVER
BOLT 8X25 T
LOCK WASHER M8
BOLT 10X25 H
LOCKWASHER M10
FLANGE FAN
STOP RING R-16
KEY 5X5X22/4DK
RUBBER COUPLING
COUPLING PIN
SOCKET HEAD SCREW 8X12 T
LEVER
1
6
6
4
1
1
1
4
4
1
1
1
1
1
1
1
1
2
2
2
2
1
1
1
1
1
4
4
4
4
1
1
1
1
6
2
1
1
9
11
12
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
36
37
38
39
40
41
63
64
SOCKET HEAD BOLT 10X25 T
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — HYDRAULIC OILTANK ASSY.
HYDRAULIC OIL TANK ASSY.
PAGE 50 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — HYDRAULIC OILTANK ASSY.
HYDRAULIC OIL TANK ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
104
050200160
501010720
501010590
501010600
502302850
502302840
502201000
502010640
502010650
953405270
953405260
953405840
953400020
001221035
030210250
031110160
959010110
952401960
920200470
O-RING P-16
JOINT 3/4-16
JOINT 3/8
1
1
1
1
1
1
1
1
1
1
1
1
1
4
4
4
1
1
1
JOINT 1/4
OIL HOSE 3/8 320L
OIL HOSE 1/4 320L
OIL TANK
ELBOW 90 DEG. 3/8
ELBOW 90 DEG. 1/4
PLUG 1/4X14 13L
PACKING 1/4 (CU)
DRAIN PLUG M18 (H)
PACKING 19302
BOLT 10X35 T
LOCKWASHER M10
FLAT WASHER M10
LEVEL GAUGE/SP-1 W/P
COLLAR 11X30X16
DECAL, OIL TANK
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — CLUTCH BOX ASSY.
CLUTCH BOX ASSY.
PAGE 52 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — CLUTCH BOX ASSY.
CLUTCH BOX ASSY.
NO.
PART NO.
502302610
502302620
502302630
040006205
040006202
501010800
080200250
951400060
501010810
501010822
501010823
501010824
501010825
501010830
502910010
501010830
060102010
001520620
501010850
501010860
001520625
501010870
050200110
501301160
501010890
001520625
501010900
501010910
502302640
951400070
952400140
030212300
020312100
001221035
030210250
952401860
953400270
953405270
PART NAME
QTY. REMARKS
1
1
1
5
1
1
1
1
1
2
CLUTCH PULLEY/IN
CLUTCH SHAFT/IN
CLUTCH SHAFT/OUT
BEARING 6205
*
3
4
*
*
5
6
BEARING 6202
CLUTCH SL1.2-20/OS225
STOP RING S-25
*
*
7
8
*
KEY 5X5X58
*
9
COLLAR 25322/BEARING
SPACER 0.8T/CLUTCH
SPACER 1.0T/CLUTCH
SPACER 2.3T/CLUTCH
SPACER 3.2T/CLUTCH
CLUTCH CASE
3
*
10
AR
AR
AR
AR
1
*
10
*
10
*
10
*
11
12
*
CLUTCH BOX ASSY. ................................... 1 ...... INCLUDES ITEMS W/
*
13
PACKING/BEARING HOLDER
OIL SEAL SB-25388
SOCKET HEAD BOLT 6X20 T
SHIFTER FORK
FORK BLOCK
SOCKET HEAD BOLT 6X25 T
SHIFTER SHAFT
2
2
8
1
2
2
1
2
1
1
4
1
1
1
2
2
2
2
4
4
4
2
2
*
14
*
15
*
16
*
17
*
18
*
19
*
20
O-RING P-11
*
21
COVER, CLUTCH CASE
PACKING, CLUTCH CASE
SOCKET HEAD BOLT 6X25 T
PLUG 3/4
PACKING 3/4
CLUTCH PULLEY/OUT
KEY 7X7X26
WASHER 13304
LOCKWASHER M12
NUT M12
BOLT 10X35 T
LOCKWASHER M10
WASHER 112545
*
22
*
23
*
24
*
25
*
26
27
28
29
30
31
32
33
34
34
*
PLUG 1/4X14 10L
PLUG 1/4X14 13L
*
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — CLUTCH BOX ASSY. (CONTINUED)
CLUTCH BOX ASSY.
PAGE 54 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — CLUTCH BOX ASSY. (CONTINUED)
CLUTCH BOX ASSY.
NO.
PART NO.
953405260
502302650
959402980
001521025
501010950
502302660
501402260
501402400
501302160
042006204
952400930
080100470
952400130
001200820
030208200
001221035
030210250
031110160
501910040
PART NAME
QTY. REMARKS
35
PACKING 1/4 (CU)
2
1
1
1
1
1
4
1
1
2
1
1
1
1
1
2
2
2
*
36
*
CLUTCH LEVER
37
*
BALL GRIP 40D-M12
SOCKET HEAD BOLT 10X25 T
BEARING HOLDER
BEARING HOLDER/INPUT SIDE
SET BOLT, L50M10M12/CLUTCH
TIGHTENER PULLEY
TIGHTENER SUPPORT
BEARING 6204ZZ
COLLAR 20252
STOP RING R-47
WASHER 9304
BOLT 8X20
38
*
39
*
40
*
42
*
43
44
45
46
47
48
49
50
51
52
53
55
#
#
#
#
#
#
#
#
#
#
#
LOCK WASHER M8
BOLT 10X35 T
WASHER, LOCK M10
WASHER, FLAT M10
BELT TIGHTENER ASSY. ............................ 1 ...... INCLUDES ITEMS W/
#
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH —VIBRATION CASE ASSY.
VIBRATION CASE ASSY.
PAGE 56 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH —VIBRATION CASE ASSY.
VIBRATION CASE ASSY.
NO.
1
2
PART NO.
502302570
502201010
502201020
502302582
502302581
951400081
951400090
952400900
001211235
030212300
502302590
001521040
040006309
080101000
080200450
060106010
060206020
952400911
502100650
502302600
001521025
502201030
953400270
953405270
953405260
001520652
031106100
001221445
030214350
502403140
502010860
070100360
502402300
953405260
502303010
502303020
502305480
920101480
PART NAME
QTY. REMARKS
VIBRATING PULLEY
ROTARY SHAFT/L
ROTARY SHAFT/R
GEAR (DRIVE-1P)
GEAR 44 (DRIVEN-2P)
KEY 10X8X17
1
1
1
1
1
2
1
3
3
3
2
8
4
2
4
1
1
1
1
1
8
1
2
2
2
8
8
14
14
1
1
2
1
1
1
1
2
1
3
4-1
4-2
5
6
7
8
9
KEY 10X8X33
WASHER 13446
BOLT 12X35 H
LOCKWASHER M12
ECCENTRIC ROTATOR
SOCKET HEAD BOLT 10X40 T
BEARING 6309
STOP RING R-100
STOP RING S-45
OIL SEAL SB-659013
OIL SEAL SC-659013
SPACER 801003
VIBRATING CASE
CASE COVER
10
11
12
13
14
15
15
16
17
18
20
21
23
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
SOCKET HEAD BOLT 10X25 T
GEAR COVER
PLUG 1/4X14 10L
PLUG 1/4X14 13L
PACKING 1/4 (CU)
SOCKET HEAD BOLT 6X60 T
FLAT WASHER M6
BOLT 14X45 T
LOCKWASHER M14
T-JOINT
NIPPLE PT1/4
V-BELT A-36
BREATHER
PACKING 1/4 (CU)
PACKING, VIBRATION CASE/A
PACKING, VIBRATION CASE/B
ECCENTRIC ROTATOR
DECAL, OIL LEVEL
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — UPPER CONTROL HANDLE ASSY.
UPPER CONTROL HANDLE ASSY.
PAGE 58 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — UPPER CONTROL HANDLE ASSY.
UPPER CONTROL HANDLE ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
1
502101480
501011090
501011100
959402980
001520620
030206150
031106100
501011110
501011120
505422750
001520615
501011140
501011150
001200835
020308060
031108160
501011162
502314420
501011180
501203980
001210615
001210620
501202200
501011220
001520652
001210615
031106100
501011310
050200160
020312100
030212300
031112230
502314410
001220615
BAR HANDLE, D.C.
TRAVELING LEVER
LINK
BALL GRIP 40D-M12
SOCKET HEAD BOLT 6X20 T
LOCK WASHER M6
FLAT WASHER M6
STEEL BALL
1
1
1
2
1
15
6
1
1
1
2
1
1
1
1
1
3
1
4
1
4
2
1
1
3
4
4
1
1
1
1
1
1
4
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
29
30
31
32
34
39
40
41
42
43
44
48
49
50
51
52
53
60
SPRING, 1.2X8X34
GUIDE
SOCKET HEAD BOLT 6X15 T
BUSH 8918, LINK
CONICAL SPRING WASHER
BOLT 8X35
NUT M8
FLAT WASHER M8
ROD END PR6-209
CABLE ASSY./C2110
CLAMP HC-40
HANDLE, D.C.
BOLT 6X15 H
BOLT 6X20 H
LEVER COVER, D.C.
LEVER GUIDE
SOCKET HEAD BOLT 6X60 T
BOLT 6X15 H
FLAT WASHER M6
VIBRATING LEVER
O-RING P-16
NUT M12
LOCK WASHER M12
FLAT WASHER M12
CABLE ASSY./C2550
BOLT 6X25 T
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — UPPER CONTROL HANDLE ASSY. (CONTINUED)
UPPER CONTROL HANDLE ASSY.
PAGE 60 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — UPPER CONTROL HANDLE ASSY. (CONTINUED)
UPPER CONTROL HANDLE ASSY.
NO.
PART NO.
PART NAME
QTY. REMARKS
61
025202020
502010930
502010940
920101290
920201100
920101280
501413650
501413660
020306050
022910090
501407790
501305190
502416960
001520815
501407810
501407820
501416950
099206008
501407840
031106100
025202012
501416970
001200830
501407880
020308060
501407890
031108160
001220815
502910020
SPLIT COTTER PIN 2X20
CLEVIS
1
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
2
2
1
1
1
1
1
1
1
1
62
63
CLEVIS PIN
93
DECAL, VIBRATION
DECAL, CLUTCH LEVER
DECAL / FORWARD & REVERSE
TURN BUCKLE
94
95
97
98
ADJUST BOLT
99
NUT M6
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
NUT M6 (L)
HANDLE PIN, D.C.
ROD, D.C.
ROD-GUIDE
SOCKET HEAD BOLT 8X15 T
ROD SPRING, D.C.
NUT, D.C.
LINK, D.C.
SOCKET HEAD SCREW 6X8 T
LINK PIN, D.C., 6X28-23
FLAT WASHER M6
SPLIT COTTER PIN 2X12
LEVER, D.C.
BOLT 8X30
GUIDE ROLLER, D.C.
NUT M8
LEVER SPRING, D.C.
FLAT WASHER M8
BOLT 8X15 T
HANDLE STOPPER
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — LOWER CONTROL HANDLE ASSY.
LOWER CONTROL HANDLE ASSY.
PAGE 62 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — LOWER CONTROL HANDLE ASSY.
LOWER CONTROL HANDLE ASSY.
NO.
2
3
4
5
6
7
8
9
PART NO.
501302670
501302680
501402860
001221245
020312100
030212300
031112230
501402870
501402880
020310080
959010413
020120160
501011162
502314420
501011180
001210615
502402900
001221020
030210250
001210620
0830000010
020306050
031106100
502402890
001220820
030208200
031108160
0012-20615
351010050
001220620
956300060
502303040
501310130
001220820
030208200
920101200
PART NAME
QTY. REMARKS
HANDLE BRACKET, RIGHT
HANDLE BRACKET, LEFT
BOLT 20X170
1
1
1
4
4
4
4
1
1
1
1
2
3
1
4
4
1
1
1
2
1
4
2
1
2
2
2
4
1
1
1
1
1
2
2
1
BOLT 12X45 T
NUT M12
LOCKWASHER M12
FLAT WASHER M12
HANDLE STOPPER
SPRING/HANDLE (1.4X18X44)
NUT M10
EYE NUT M10
NUT M20, P1.5
ROD END PR6-209
CABLE ASSY./C2110
CLAMP HC-40
BOLT 6X15 H
CABLE STOPPER
BOLT 10X20 T
LOCKWASHER M10
BOLT 6X20 H
COIL SPRING
10
11
12
28
29
30
31
34
36
37
38
39
45
46
47
56
57
58
59
60
64
76
87
88
89
90
91
96
NUT M6
FLAT WASHER M6
CABLE STOPPER
BOLT 8X20 T
LOCK WASHER M8
FLAT WASHER M8
BOLT 6x15 T
GREASE FITTING A-MT6X1
BOLT 6X20 T
THROTTLE LEVER AY 22
THROTTLE WIRE S520-640
LEVER HOLDER
BOLT 8X20 T
LOCK WASHER M8
DECAL, GREASE
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — ENGINE ASSY.
ENGINE ASSY.
PAGE 64 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — ENGINE ASSY.
ENGINE ASSY.
NO.
68
69
72
75
76
77
78
79
80
81
82
105
PART NO.
PART NAME
QTY. REMARKS
912234007
502403290
031110160
020310080
030210250
001221230
030212300
952400600
502454370
070200580
099208012
502339880
ENGINE, HONDA GX340K1QAE2
KEY 32 X6 32X48
WASHER, FLAT
1
1
4
4
4
4
4
4
1
2
1
1
NUT M10
WASHER, LOCK
BOLT 12X30 T
WASHER, LOCK
WASHER, FLAT 13X28X4.5
PULLEY, ENGINE
V-BELT B-58
SOCKET HEAD SCREW 8X12 T
ENGINE MOUNTING PLATE
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — BATTERY ASSY.
BATTERY ASSY.
PAGE 66 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
MDR-9GH — BATTERY ASSY.
BATTERY ASSY.
NO.
70
71
72
73
74
75
76
77
78
79
80
PART NO.
502215490
001200815
030208200
502403310
502403320
020308060
030208200
031108160
607010030
502301040
502301050
PART NAME
BATTERY BASE (GX340)
BOLT 8X15
WASHER, LOCK M8
BATTERY PROTECT
BOLT/BATTERY
QTY. REMARKS
1
4
4
1
2
4
2
2
1
1
1
NUT M8
WASHER, LOCK M8
WASHER, FLAT M8
BATTERY 12N24-3.26A19L
BATTERY CORD (+) 220
BATTERY CORD (-) 380
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 68 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
*
4
5
*
6
PART NO.
PART NAME
QTY.
REMARKS
16271ZE3010
17210ZE3505
17218ZE3505
17231ZE3W00
17232891000
17235ZH9N00
17238ZE2310
17239ZE1000
17410ZH9N00
90203ZA0800
934040602008
9405006000
GASKET, ELBOW
1
ELEMENT, AIR CLEANER ........................ 1 ......... INCLUDES ITEMS W/
FILTER, OUTER
COVER, AIR CLEANER
GROMMET, AIR CLEANER
NOSE, MUFFLER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER ............................ 1 ......... INCLUDES ITEMS W/
WINGNUT, 6MM
BOLT-WASHER, 6X20
NUT, FLANGE 6MM
*
1
1
1
1
2
1
7
8
9
#
#
#
11
13
14
1
1
2
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 70 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
PART NO.
14100ZE3020
PART NAME
QTY.
REMARKS
CAMSHAFT ASSEMBLY .......................... 1 ......... USE FROM ENGINE SN 2708027
............................................................................... INCLUDES ITEMS W/
CAMSHAFT ASSEMBLY .......................... 1 ......... USE UP TO ENGINE SN 2708026
............................................................................... INCLUDES ITEMS W/
*
1
14100ZE3305
*
2
3
4
5
6
*
7
8
14410ZE3013
14431ZE2010
14441ZE2000
14451ZE1013
14568ZE1000
14711ZE3000
14721ZE3000
14751ZE2003
14771ZE2000
14773ZE2000
14775ZE2010
14781ZE2000
14791ZE2010
90012ZE0010
90206ZE1000
12209ZE8003
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, INTAKE
2
2
2
2
1
1
1
2
1
1
1
1
1
2
2
VALVE, EXHAUST
SPRING, VALVE
9
10
11
12
13
14
15
16
17
RETAINER, INTAKE VALVE SPRING
RETAINER, EXHAUST VALVE SPRING
SEAT, VALVE SPRING
ROTATOR, VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
NUT, PIVOT ADJ.
SEAL, VALVE STEM................................. 1 ......... USE FROM ENGINE SN 3334264
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 72 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2
3
4
4
6
7
8
9
# % +
16010ZE2812
16011ZA0931
16013ZA0931
16015ZE2005
16015ZE8005
16024ZE1811
16028ZE0005
16044ZE3811
16100ZE3V01
16124ZE0005
16166ZE3W50
16172ZE3W10
16173001004
16211ZE3000
16220ZA0702
16221ZE3800
16223ZE3800
16610ZE1000
16953ZE1406
16953ZE1812
16954ZE1811
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
93500030080G
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
*
*
*
*
*
*
*
*
CHAMBER SET, FLOAT .........................1............. INCLUDES ITEMS W/
CHAMBER SET, FLOAT .........................1............. INCLUDES ITEMS W/
SCREW SET, DRAIN
SCREW SET B ......................................1............. INCLUDES ITEM W/
CHOKE SET
CARBURETOR ASSEMBLY, BE80B B ..1............. INCLUDES ITEMS W/
SCREW, THROTTLE STOP
NOZZLE, MAIN
COLLAR, SET
GASKET, FUEL STRAINER CUP
INSULATOR, CARBURETOR
SPACER, CARBURETOR
GASKET, CARBURETOR
GASKET, INSULATOR
#
#
#
1
%
1
*
10
11
12
13
14
15
16
17
18
19
19
20
21
22
23
24
24
1
1
1
1
1
1
1
1
*
LEVER, CHOKE (STANDARD) ...............1............. INCLUDES ITEM W/$
LEVER, VALVE ......................................1............. USE UP TO ENGINE SN BE80B A
LEVER, VALVE ......................................1............. USE FROM ENGINE SN BE80B B
PLATE, LEVER SETTING ......................1............. USE UP TO ENGINE SN BE80B A
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3X6 ..................................2............. USE FROM ENGINE SN BE80B B
SCREW, PAN 3X8 ..................................2............. USE UP TO ENGINE SN BE80B A
*
*
*
1
1
1
*
*
*
*
25$
PIN, SPRING 2X12
1
1
1
1
26
99101ZH80880
99101ZH80900
99101ZH80920
99204ZE00350
JET, MAIN #88 (OPTIONAL)
JET, MAIN #90 (OPTIONAL)
JET, MAIN #92
*
26
*
26
*
27
JET SET, PILOT #35 .............................. 1............. INCLUDES ITEM W/+
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CONTROL ASSY.
CONTROL ASSY.
PAGE 74 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CONTROL ASSY.
CONTROL ASSY.
NO.
2
3
4
5
PART NO.
PART NAME
ARM, GOVERNOR
ROD, GOVERNOR
SPRING, GOVERNOR
SPRING,THROTTLE RETURN
CONTROL ASSEMBLY, REMOTE ........... 1.......... INCLUDES ITEMS W/
LEVER CONTROL
SPRING, LEVER
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE CONTROL
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE 6X12 (CT200)
BOLT, GOVERNOR ARM
NUT, SELF- LOCK 6MM
SCREW, PAN 5X32
QTY.
REMARKS
16551ZE3000
16555ZE3000
16561ZE3000
16562ZE3000
16570ZE3W20
16571ze3W00
16574ZE1000
16575ZE2W00
16576891000
16578ZE1000
16581ZE3W00
16584883300
16592883310
90013883000
90015ZE5010
90114SA0000
93500050320A
93500050160A
9405006000
1
1
1
1
8
*
11
1
1
1
1
1
1
1
1
2
1
1
1
1
1
*
12
*
13
*
14
*
15
*
16
*
19
*
20
23
*
24
26
*
29
*
32
*
SCREW, PAN 5X16
NUT, FLANGE 6MM
33
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CONTROL BOX ASSY.
CONTROL BOXASSY.
PAGE 76 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
1
PART NO.
31610ZE3W23ZB
PART NAME
QTY.
REMARKS
BOX ASSY., CONTROL (EXTERNAL- ...... 1.......... INCLUDES ITEMS W/
ALERT/3A) *R8* BRIGHT RED
*
2
*
3
*
4
*
5
*
31612ZE2003
31614ZE2003
31615ZE3003ZB
31700124003
32127738700
32197ZE1003
32902892003
35100ZE2842
35111880003
36103ZE1000
38240ZE2840
38250ZA8701
87529ZE2811
90013883000
90380MA6010
90630751000
90672SA0003
91406ZE2003
93500030120H
93500040120H
94001043900S
9411104800
CASE, CONTROL
BRACKET, CASE MOUNTING
PANEL, CONTROL *R8* BRIGHT RED
1
1
1
RECTIFIER ASSY., SILICON (STANLEY) 1
6
7
#
SUSPENSION, CONNECTOR
SUB- HARNESS
BAND
1
1
1
*
*
8
9
SWITCH ASSEMBLY, COMBINATION ...... 1.......... INCLUDES ITEMS W/
#
*
10
11
12
#
KEY
1
1
1
1
1
1
1
1
1
1
2
1
*
HOLDER, STOP SWITCH WIRE
PROTECTOR, CIRCUIT 3.5A
LENS ASSEMBLY, PROTECTOR
PANEL, CONTROL BOX (EXTERNAL)
BOLT, FLANGE 6X12 (CT200)
SCREW, SPECIAL 6X12
CLIP, PURSE LOCK
STRAP, CABLE 118MM *NHL* BLACK
TUBE, FASTENER 30
SCREW, PAN 3X12
*
*
*
13
14
15
16
17
18
19
20
21
22
23
*
*
*
*
*
SCREW, PAN 4X12
NUT, HEX. 4MM ........................................2.......... USE FROM ENGINE SN 2801238
WASHER, SPRING 4MM
FUSE, BLADE 15A
1
1
24
25
#
9820031500
34150ZH7003
9410104800
*
ALERT UNIT, OIL ......................................1.......... USE FROM ENGINE SN 2801238
WASHER, PLAIN 4MM .............................1.......... USE FROM ENGINE SN 2801238
*
*
26
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 78 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
1
*
2
PART NO.
PART NAME
QTY.
REMARKS
06165ZE3000
11300ZE3602
11381ZE3800
11381ZE3801
15600ZG4003
15600735003
15625ZE1003
15625ZE1003
16510ZE3000
16511ZE8000
16512ZE3000
16513ZE2000
16531ZE2000
90602ZE1000
90701HC4000
91201ZE3004
9410106800
GOVERNOR KIT, OPTIONAL ........................ 1 ......... INCLUDES ITEMS W/
COVER ASSY., CRANKCASE (Q TYPE)....... 1 ......... INCLUDES ITEMS W/
#
*
3
3
4
5
7
8
GASKET, CASE COVER
GASKET, CASE COVER
CAP ASSEMBLY OIL FILLER
CAP ASSEMBLY OIL FILLER
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
GOVERNOR ASSEMBLY............................... 1 ......... INCLUDES ITEMS W/
WEIGHT, GOVERNOR
HOLDER, GOVERNORWEIGHT
PIN, GOVERNOR WEIGHT
SLIDER, GOVERNOR
CLIP, GOVERNOR HOLDER
PIN, DOWEL 8X12
1
1
1
1
1
1
9
#
%
*
10 #%
3
1
3
1
1
2
1
1
7
1
1
*
11 #%
*
12 #%
*
13
15
16
17
#
#
*
*
OIL SEAL 35X52X8
WASHER, PLAIN 6MM
BOLT, FLANGE 8X40
BEARING, RADIAL BALL 6202
BEARING, RADIAL BALL 6207
*
18
#
*
19
20
21
957010804000
961006202000
961006207000
*
*
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
PAGE 80 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CRANKSHAFT ASSY.
CRANKSHAFT ASSY.
NO.
1
5
6
7
PART NO.
PART NAME
QTY.
REMARKS
13310ZE3601
13351ZE3010
90745ZE2600
961006207000
CRANKSHAFT, Q- TYPE
WEIGHT, BALANCER
KEY 6.3X6.3X43
1
1
1
1
BEARING, RADIAL BALL 6207
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 82 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
1
PART NO.
12000ZE3826
PART NAME
QTY.
REMARKS
CYLINDER ASSY., (SELF STARTER........ 1.......... INCLUDES ITEMS W/
+ ALERT)
*
2
3
4
5
6
6
7
15510ZE2043
16541ZE3010
32197ZE2003
90013883000
90131883000
90131896650
90446KE1000
91201ZE3004
91201ZE9003
91203952771
91353671003
9405010000
SWITCH ASSEMBLY, OIL LEVEL
SHAFT, GOVERNOR ARM
1
1
SUB- HARNESS ....................................... 1.......... USE UP TO ENGINE SN 2639737
BOLT, FLANGE 6X12 (CT200) .................. 1.......... USE UP TO ENGINE SN 2639737
BOLT, DRAIN PLUG
BOLT, DRAIN PLUG
WASHER 8.2X17X0.8
OIL SEAL 35X52X8
OIL SEAL 8X14X5
2
2
1
1
1
1
1
1
2
1
2
1
9
*
10
10
11
12
13
14
15
OIL SEAL 8X14X5
O- RING 13.5X1.5 (ARAI)
NUT, FLANGE 10MM
WASHER, DRAIN PLUG 12MM
PIN, LOCK 10MM
BOLT, FLANGE 6X12
BEARING, RADIAL BALL 6202
9410912000
9425110000
957010601200
961006202000
16
*
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 84 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
1
1
2
*
3
*
4
*
5
6
7
PART NO.
PART NAME
QTY.
REMARKS
12200ZF6W00
12200ZF6W01
12204ZE2306
12205ZE2305
12216ZE2300
12251ZE3W00
12310ZE3791
12315ZE3840
12391ZE2020
90014ZE2000
90042ZE8000
90047ZE2000
92900080320E
90441ZE2010
9430112200
CYLINDER HEAD ......................................... 1 .......... INCLUDES ITEMS W/
CYLINDER HEAD ......................................... 1 .......... INCLUDES ITEMS W/
*
*
GUIDE, VALVE OS (OPTIONAL)
GUIDE, EXHAUST VALVE OS (OPT.)
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER, HEAD
TUBE, BREATHER
GASKET, CYLINDER HEAD COVER
BOLT, HEAD COVER
1
1
1
1
1
1
1
1
2
8
10
11
12
12
13
14
15
15
16
16
16
16
BOLT, STUD 8X131.5
BOLT, STUD 8X47......................................... 2 .......... USE UP TO ENGINE SN 3033461
BOLT 2, STUD 8X32 ..................................... 2 .......... USE FROM ENGINE SN 3033462
WASHER, HEAD COVER
PIN A, DOWEL 12X20
BOLT, FLANGE 10X80
1
2
4
4
1
1
1
1
957011008000
957251008000
9807955846
9807955855
9807956846
BOLT, FLANGE 10X80
SPARK PLUG BPR5ES (NGK) (OPT.)
SPARK PLUG W16EPR-U (DENSO) (OPT.)
SPARK PLUG BPR6ES (NGK)
SPARK PLUG W20EPR- U (DENSO)
9807956855
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 86 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — FAN COVER ASSY.
FAN COVER ASSY.
NO.
1
2
3
6
PART NO.
PART NAME
QTY.
REMARKS
16731ZE2003
19610ZE3010ZA
19631ZE3W00
81329567020
90013883000
CLIP, TUBE
1
1
1
1
6
COVER, FAN *R8* BRIGHT RED
SHROUD
GROMMET, DRAIN HOLE
BOLT, FLANGE 6X12 (CT200)
7
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 88 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
3
6
6
7
PART NO.
PART NAME
QTY.
REMARKS
19511ZE3000
28450ZE3W11
31100ZE3W01
90201ZE3V00
90201ZE3790
90741ZE2000
FAN, COOLING
1
1
1
PULLEY, STARTER (SCREEN GRID)
FLYWHEEL, 4 POLE
NUT, SPECIAL 16MM (1) .............................. 1 .......... USE FROM ENGINE SN 2536523
NUT, SPECIAL 16MM ................................... 1 .......... USE UP TO ENGINE SN 2536522
KEY, SPECIAL WOODRUFF 25X18
1
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 90 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
5
PART NO.
PART NAME
RUBBER, SUPPORTER 107MM
JOINT, FUEL TANK
TANK, FUEL *NH31* MCKINLEY WHITE
CAP, FUEL FILLER ....................................... 1 .......... USE UP TO ENGINE SN 4122402
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE3010ZA
17620ZH7023
1
1
1
.................................................................................... INCLUDES ITEMS W/
CAP, FUEL FILLER ....................................... 1 .......... USE FROM ENGINE SN 4122403
.................................................................................... INCLUDES ITEMS W/
*
5
17620ZH7023
*
6
*
7
10
11
12
13
14
17631ZH7003
17672ZE2W01
91353671003
9405008000
950014500360M
9500202080
GASKET, FUEL FILLER CAP
FILTER, FUEL
O- RING 13.5X1.5 (ARAI)
NUT, FLANGE 8MM
BULK HOSE, FUEL (4.5X3000) (4.5X235)
CLIP, TUBE B8
BOLT, FLANGE 8X25
1
1
1
2
1
2
2
957010802500
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 92 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
3
4
5
7
8
9
PART NO.
PART NAME
QTY.
REMARKS
30500ZE2023
30700ZE1013
31511ZE3000
31512ZE2000
31630ZE2841
36101ZE2701
90012888000
90013883000
90015883000
COIL ASSEMBLY, IGNITION
CAP ASSEMBLY, NOISE SUPPRESSOR
CLAMP, WIRE
1
1
1
1
1
1
2
1
2
GROMMET, WIRE
COIL ASSEMBLY, CHARGE (3A)
WIRE, STOP SWITCH 430MM
BOLT, FLANGE 6X40
BOLT, FLANGE 6X12 (CT200)
BOLT, FLANGE 6X28
10
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — STARTER MOTOR ASSY.
STARTER MOTOR ASSY.
HONDA GX340K1QAE2 — MANUALS ASSY.
PAGE 94 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — STARTER MOTOR ASSY.
STARTER MOTOR ASSY.
NO.
PART NO.
PART NAME
CONTACTOR ASSEMBLY
ARMATURE
CLUTCH, OVERRUNNING
MOTOR UNIT, STARTER............................... 1 .......... INCLUDES ITEMS W/
BRACKET, CENTER
BRACKET, FRONT
GEAR, DRIVE PINION
BRUSH
QTY.
REMARKS
1
*
2
*
3
*
4
31204ZA0003
31206ZE3003
31207ZE3003
31201ZE3013
31211ZE2003
31212ZE3003
31213ZE2003
31215ZE2003
31218ZE3003
31219ZE2003
31222ZE3791
31231ZE2003
31232ZE3003
31233ZE2003
90110ZE2003
91601ZE2003
90007ZE2003
938920501408
938920503208
9407006080
1
1
1
*
5
6
1
1
1
2
1
4
1
1
1
1
1
1
*
*
7
8
*
*
9
YOKE
*
10
SPRING, BRUSH RETURN
GEAR, REDUCTION
HOLDER, BRUSH
WIRE, WATER COVER
INSULATOR
SCREW- WASHER 4X6
GASKET
BOLT- WASHER 5X14 ................................... 2 .......... USE FROM ENGINE SN 2630807
SCREW- WASHER 5X14 ............................... 2 .......... USE UP TO ENGINE SN 2630806
SCREW- WASHER 5X3
NUT- WASHER 6MM
BOLT, FLANGE 8X35
*
11
*
12
*
13
*
14
*
15
*
16
*
17
*
17
18
*
4
2
2
*
19
*
20
957010803508
HONDA GX340K1QAE2 — MANUALS ASSY.
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 96 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
4
5
6
6
8
PART NO.
PART NAME
QTY.
REMARKS
18310ZE3W00
18320ZE3W01
18323ZE3W40
18330ZE2W00
18331ZE3810
18333ZF6W01
18333ZK6Y00
18355ZE2W10
18381ZE2W10
90013883000
90050ZE1000
90055ZE1000
93500060060B
9405008000
MUFFLER
1
1
1
1
1
PROTECTOR, MUFFLER
PROTECTOR, EXHAUST PIPE
PIPE, EXHAUST
CAP, MUFFLER
GASKET, EXHAUST PIPE............................ 1 .......... USE FROM ENGINE SN 3030998
GASKET, EXHAUST PIPE (WACKER) ......... 1 .......... USE UP TO ENGINE SN 3030997
ARRESTER, SPARK
GASKET, MUFFLER (ARRESTER)
BOLT, FLANGE 6X12 (CT200)
SCREW, TAPPING 5X8
SCREW, TAPPING 4X6
SCREW, PAN 6X6
1
1
1
6
3
1
5
9
11
12
13
14
15
NUT, FLANGE 8MM
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — PISTON ASSY.
PISTON ASSY.
PAGE 98 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
PART NO.
PART NAME
QTY.
REMARKS
13010ZE3003
13011ZE3003
13012ZE3003
13013ZE3003
13101ZE3W00
13102ZE3W00
13103ZE3W00
13104ZE3W00
13111ZF6000
13200ZE3010
13200ZE3315
RING SET, PISTON (STANDARD)
RING SET, PISTON (OS 0.25) (OPT.)
RING SET, PISTON (OS0.50) (OPT.)
RING SET, PISTON (0.75) (OPTIONAL)
PISTON, STANDARD
1
1
1
1
1
1
1
1
1
1
1
PISTON, OS 0.25 (OPTIONAL)
PISTON, OS 0.50 (OPTIONAL)
PISTON, 0.75 (OPTIONAL)
PIN, PISTON
ROD ASSEMBLY, CONNECTING (STD.)
ROD ASSEMBLY CONNECTING
(US 0.25) OPTIONAL
3
4
4
5
6
90001ZE8000
90601ZE3000
BOLT, CONNECTING ROD
CLIP, PISTON PIN 20MM
2
2
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 100 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
28400ZE3W01ZA STARTER ASSEMBLY, RECOIL ................... 1 .......... INCLUDES ITEMS W/
*R8* BRIGHT RED
*
2
28410ZE3W01ZA CASE, RECOIL STARTER
*R8* BRIGHT RED
1
*
3
4
28421ZE3W01
28422ZE2W01
28441ZE2W01
28442ZE2W01
28443ZE2W01
28444ZE2W01
28445ZE2W01
28461ZE2W02
28462ZV7003
28469ZE2W01
90004ZE2W01
957010600800
PULLEY, RECOIL STARTER
RATCHET, STARTER
SPRING, FRICTION
SPRING, STARTER RETURN
SPRING RATCHET
RETAINER, SPRING
HOLDER, SPRING
GRIP, STARTER
1
2
1
1
2
1
1
1
1
*
*
5
6
*
*
7
8
*
*
9
*
10
*
11
ROPE, RECOIL STARTER
*
12
*
GRIP, REINFORCEMENT ............................. 1 .......... USE UP TO ENGINE SN 2935312
13
*
SCREW, CENTER
BOLT, FLANGE 6X8
1
3
14
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — LABELS ASSY.
LABELS ASSY.
PAGE 102 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX340K1QAE2 — LABELS ASSY.
LABELS ASSY.
NO.
1
3
4
6
PART NO.
PART NAME
QTY.
REMARKS
87521ZE3W01
87522ZH9000
87528ZE2810
87532ZH8810
EMBLEM
1
1
1
1
LABEL, CAUTION
MARK, CHOKE (EXTERNAL)
MARK, OIL ALERT (E)
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: October 1, 2002
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 10 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 104 — MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
MQ-MIKASA MDR-9GH VIBRATORY ROLLER — OPERATION AND PARTS MANUAL — REV. #0 (12/17/03) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
MULTIQUIP’SMAINPHONENUMBERS
800-421-1244
310-537-3700
FAX: 310-537-3927
PARTSDEPARTMENT
800-427-1244
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
MAYCOPARTS
800-306-2926
310-537-3700
FAX: 800-672-7877
FAX: 310-637-3284
SERVICEDEPARTMENT
800-478-1244
310-537-3700
FAX: 310-537-4259
MQPOWERSERVICEDEPARTMENT
800-835-2551
310-537-3700
FAX: 310-638-8046
TECHNICALASSISTANCE
800-478-1244
FAX: 310-631-5032
WARRANTYDEPARTMENT
800-421-1244, EXT. 279 FAX: 310-537-1173
310-537-3700, EXT. 279
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
manufactured for Multiquip Inc.
by
MIKASA SANGYO CO., LTD. Tokyo, Japan
Download from Www.Somanuals.com. All Manuals Search And Download.
|