OPERATION AND PARTS MANUAL
WHISPERWATTTM SERIES
MODELS:
DCA-300SSK
DCA-300SSK2
DCA-300SSK3
60 Hz GENERATORS
PARTS LIST NO. C2871300704
SERIAL NO. 3708297~
Revision #4 (03/27/06)
THIS MANUAL MUST ACCOMPANY
THE EQUIPMENT AT ALLTIMES.
Download from Www.Somanuals.com. All Manuals Search And Download.
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
MQ POWER CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
800-421-1244
FAX:310-632-2656
Internet:www.mqpower.com
PARTS DEPARTMENT
800-427-1244
310-537-3700
FAX:800-672-7877
FAX:310-637-3284
SERVICE DEPARTMENT
800-835-2551
FAX:310-638-8046
310-537-3700
TECHNICAL ASSISTANCE
800-835-2551
WARRANTYDEPARTMENT
800-835-2551,EXT.279
310-537-3700,EXT.279
FAX:310-638-8046
FAX:310-638-8046
© COPYRIGHT 2006, MULTIQUIP INC.
MQ Power Inc, Ultra-Silent series, and the MQ Power logo are registered trademarks of Multiquip Inc. and may not be used,
reproduced, or altered without written permission. All other trademarks are the property of thier respective owners and used with
permission.
This manual MUST accompany the equipment at all times.This manual is considered a permanent part of the equipment and should
remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are
based on the DCA-300SSK SERIES WHISPERWATT AC Generators. Multiquip Inc. reserves the right to discontinue or change
specifications, design or the information published in this publication at any time without notice and without incurring any obligations.
To find the latest revision of this
publication, visit our website at:
www.mqpower.com
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
COMPONENT DRAWINGS
MQPower DCA-300SSK
SERIES AC Generator
California Proposition 65 Warning .....................................2
Generator Assembly.................................................. 64-67
Control Box Assembly............................................... 68-73
Engine & Radiator Assy. (S/N 3697258 & Below )..... 74-77
Engine & Radiator Assy. (S/N 3708270-3708296) ..... 78-79
Engine & Radiator Assy. (S/N 3708270 & Above) ..... 80-83
Engine Operating Panel Assembly ............................ 84-85
Output Terminal Assembly......................................... 86-89
Actuator Assembly .................................................... 90-91
Battery Assembly ...................................................... 92-93
Muffler Assembly ...................................................... 94-95
Fuel Tank Assembly .................................................. 96-97
Enclosure Assembly (S/N 3708296 and Below) ...... 98-103
Enclosure Assembly (S/N 3708297 and Above).... 104-109
Rubber Seal Assembly .......................................... 110-111
Oil Piping Assembly .............................................. 112-113
Name Plate and Decals ......................................... 114-119
Here's How To Get Help ....................................................3
Table Of Contents .............................................................4
Parts Ordering Procedures ...............................................5
Specifications Generator/Engine ......................................6
Dimensions (Top, Side and Front) .....................................7
Safety Alert Messages Symbols...................................8-9
Rules for Safe Operation ........................................... 10-13
Generator Decals ..................................................... 14-15
Installation ................................................................. 16-17
General Information ........................................................ 18
Major Components ......................................................... 19
Generator Control Panel (S/N 3701673 and Below) ........ 20
Generator Control Panel (S/N 3701674 and Above) ........ 20
Generator Control Panel Description............................... 21
Engine Operating Panel (S/N 3701673 and Below) ......... 22
Engine Operating Panel (S/N 3701674 and Above) ........ 22
Engine Operating Panel Description ............................... 23
OutputTerminal Panel Overview ................................ 24-26
Load Application ............................................................. 27
Generator Outputs .......................................................... 28
Generator Outputs/Gauge Reading................................. 29
OutputTerminal Panel Connections ........................... 30-31
Pre Setup .................................................................. 32-36
Generator Start-up Procedure (Key Switch) .............. 37-39
Generator Start-up Procedure (Manual MPEC) .............. 40
Generator Start-up Procedure (Auto MPEC) .................. 41
Generator Shutdown Procedure ...................................... 42
Maintenance .............................................................. 44-48
Trailer Maintenance.................................................... 49-52
TrailerWiring Diagram ..................................................... 53
Generator Wiring Diagram ............................................... 54
EngineWiring Diagram (S/N 3696506 and Below) .......... 55
Engine Wiring Diagram (S/N 3696507 to 3701673) ......... 56
Engine Wiring Diagram (S/N3701674 and Above) ........... 57
EngineTroubleshooting .............................................. 58-59
GeneratorTroubleshooting .............................................. 60
Engine ContollerTroubleshooting (MPEC) ...................... 61
Explanation of Codes in Remarks Column ..................... 62
Suggested Spare Parts .................................................. 63
Terms and Condition of Sale — Parts .......................... 120
Specification and part
number are subject to
NOTE
change without notice.
PAGE 4 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
When ordering parts,
please supply the following information:
❒
Dealeraccountnumber
❒
❒
❒
❒
❒
❒
Dealernameandaddress
Shipping address (if different than billing address)
Returnfaxnumber
Applicable model number
Quantity,part number and description of each part
Specifypreferredmethodofshipment:
✓FedEx or UPS Ground
✓FedEx or UPS Second Day or Third Day
✓FedEx or UPS Next Day
✓Federal Express Priority One
✓DHL
Note:Unlessotherwiseindicatedbycustomer, all
orders are treated as “Standard Orders”, and will
ship within 24 hours.We will make every effort to
ship “Air Shipments” the same day that the order is
received, if prior to 2PM west coast time. “Stock
Orders” must be so noted on fax or web forms.
✓Truck
Place Your Parts Order Via Web or Fax
For Even More Savings!
Here’s how to get help...
Please have the model and serial number
on hand when calling.
(Domestic USA Dealers Only)
MQ POWER CORPORATE OFFICE
18910 Wilmington Ave.
Carson, CA 90746
Email: [email protected]
Internet: www.mqpower.com
800-421-1244
FAX: 310-632-2656
Extra Discounts!
All parts orders which include complete part numbers and
are received by our automated web parts order system, or
by fax qualify for the following extra discounts:
Ordered
via
Standard
orders
Stock orders
PARTS DEPARTMENT
800-427-1244
310-537-3700
SERVICE DEPARTMENT
800-835-2551
310-537-3700
TECHNICAL ASSISTANCE
800-835-2551
WARRANTY DEPARTMENT
800-835-2551, EXT. 279
310-537-3700, EXT. 279
($750 list and above)
FAX: 800-672-7877
FAX: 310-637-3284
Fax
3%
5%
10%
10%
Web
FAX: 310-638-8046
Special freight allowances
when you order 10 or more
line items via Web or Fax!**
FedEx Ground Service at no charge for freight
No other allowances on freight shipped by any other carrier.
FAX: 310-638-8046
FAX: 310-638-8046
**Common nuts, bolts and washers (all items under $1.00
list price) do not count towards the 10+ line items.
NOTE:DISCOUNTSARESUBJECTTOCHANGE
MQPOWER
Direct TOLL-FREE access
to our Parts Department:
ADivisionofMultiquipInc.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-632-2656
Toll-free nationwide — 800-427-1244
INTERNET:www.mqpower.com
Toll-free FAX — 800-6-PARTS-7 (800/672-7877)
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — SPECIFICATIONS
Table 1. Generator Specifications
Revolving field,Self-ventilated
Drip-proof-Single bearing
Design
No. of Poles
Excitation
4-pole
Brushless with AVR
Standby Output
Prime Output
264 KW (330 KVA)
240 KW (300 KVA)
Generator RPM
Voltage — 3Ø
Voltage — 1Ø
Armature Connection
1800
208, 220, 240, 416, 440, 480V Reconnectable
120, 127, 139, 240, 254, 277V Adjustable
Star with neutral
Voltage Regulation
(No load to full load)
1.5%
Power Factor
Frequency
0.8
60 Hz
Frequency Regulation:
No load to full load
Isochronous under varying loads from no load to 100% rated load
Frequency Regulation:
Steady State
+0.25% of mean value for constant loads from no load to full load
Insulation
Sound Level dB(A)
Full load at 23 feet
Class F
71
Dimensions Approx.
(L x W x H)
153 x 56 x 71 in. (389 x 142 x 180 mm.)
9,172 lbs. (4,160 kg.)
Dry Net Weight
Table 2. Engine Specifications
Model
Type
KOMATSU SA6D125E-2
KOMATSU SAA6D125E-2
4 Cycle, water-cooled, direct
injection, turbocharged with after-
cooler
4 Cycle, water-cooled, direct injection,
turbocharged with air to air after-cooler
No. of Cylinders
Bore x Stroke
Rated Output
Displacement
Starting
6 cylinders
4.9 in. x 5.9 in. (125 mm x 150 mm)
345hp/1800 rpm 354hp/1800 rpm
673 cu. in. (11,040 cc)
Electric
Coolant Capacity
Lube Oil Capacity
Fuel Consumption
Battery
8.5 gal. (32.6 liters)
16.1 gal. (60 liters)
9.8 gal. (37 liters)
16.4 gal. (62 liters)
17.5 gal. (66.5L)/hr at full load
16.7gal. (63.2L)/hr at full load
12V- 150AH x 2
#2 Diesel Fuel
Fuel
PAGE 6 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — DIMENSIONS (TOP, SIDE AND FRONT)
r Dimension in. (mm.)
42.32 in. (1,075 mm.)
147.64 in. (3,750 mm.)
70.98 in. (1,800 mm.)
55.12 in. (1,400 mm.)
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY AND THE SAFETY OF OTHERS!
HAZARD SYMBOLS
Potential hazards associated with the operation of this
equipment will be referenced with "Hazard Symbols" which
appear throughout this manual, and will be referenced in
conjunction with Safety "Message Alert Symbols".
Safety precautions should be followed at all times when
operating this equipment.Failure to read and understand the
Safety Messages and Operating Instructions could result in
injury to yourself and others.
This Owner's Manual has been
developed to provide complete
instructions for the safe and
efficient operation of the
MQ Power Model DCA-400SSVU
Whisperwatt™ Generator.
WARNING - LETHAL EXHAUST GASES
NOTE
Gasoline engine exhaust gases contain
poisonous carbon monoxide. This gas is
colorless and odorless, and can cause
DEATH if inhaled. NEVER operate this
Before using this generator, ensure that the operating
individual has read and understands all instructions in
this manual.
equipment in a confined area or enclosed structure that
does not provide ample free flow air.
WARNING - EXPLOSIVE FUEL
SAFETY MESSAGE ALERT SYMBOLS
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
DO NOT fill the fuel tank while the engine
is running or hot.
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER, WARNING, or CAUTION.
DO NOT overfill tank, since spilled fuel could ignite if it
comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
NEVER use fuel as a cleaning agent.
DANGER
You WILL be KILLED or SERIOUSLY injured if you
do not follow directions.
WARNING
WARNING - BURN HAZARDS
Engine components can generate extreme
heat.To prevent burns, DO NOT touch these
areas while the engine is running or
immediately after operations. NEVER
operate the engine with heat shields or heat
guards removed.
You COULD be KILLED or SERIOUSLY injured if
you do not follow directions.
CAUTION
You CAN be injured if you do not follow directions
DANGER - ELECTROCUTION HAZARDS
During operation of this generator, there
exists the possibility of electrocution,
electrical shock or burn, which can cause
severe bodily harm or even DEATH!
PAGE 8 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — SAFETY MESSAGE ALERT SYMBOLS
WARNING - ROTATING PARTS
CAUTION - RESPIRATORY HAZARDS
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
ALWAYS wear approved respiratory
protection.
CAUTION - ACCIDENTAL STARTING
CAUTION - SIGHT AND HEARING HAZARDS
ALWAYS place the Engine ON/OFF
switch in the OFF position and remove
the ignition key when the pump is not in
use.
ALWAYS wear approved eye and
hearing protection.
CAUTION - OVER-SPEED CONDITIONS
CAUTION - EQUIPMENT DAMAGE MESSAGES
NEVER tamper with the factory settings
of the engine governor or settings.
Personal injury and damage to the engine
or equipment can result if operating in
speed ranges above maximum allowable.
Other important messages are provided throughout this
manual to help prevent damage to your generator, other
property, or the surrounding environment.
This generator, other property,
or the surrounding environment
could be damaged if you do not
follow instructions.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — RULES FOR SAFE OPERATION
■
■
ALWAYS check the machine for loosened threads or bolts
before starting.
DANGER - READTHIS MANUAL!
Failure to follow instructions in this manual may lead to
serious injury or even DEATH! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
NEVER operate the generator in an explosive atmosphere
or near combustible materials. An explosion or fire could
result causing severe bodily harm or even death.
■
■
NEVER touch the hot exhaust manifold, muffler
or cylinder. Allow these parts to cool before
servicing engine or generator.
The following safety guidelines should always be used when
operating the DCA-400SSVUWhisperwatt™ AC Generator.
HighTemperatures – Allow the engine
to cool before performing service and
maintenance functions. Contact with
hot! components can cause serious
burns.
General Safety:
■
DO NOT operate or service this
equipment before reading this entire
manual.
The operator MUST BE familiar with proper safety
precautions and operations techniques before using
generator.
■
The engine of this generator requires an adequate free
flow of cooling air. NEVER operate the generator in any
enclosed or narrow area where free flow of the air is
restricted. If the air flow is
restricted it will cause serious
damage to the generator or
engine and may cause injury
to people. The generator
engine gives off DEADLY
■
■
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
carbon monoxide gas.
■
■
■
■
■
DO NOT place hands or fingers inside generator engine
compartment when engine is running.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, illness or taking
medicine.
NEVER run engine without air filter.Severe engine damage
may occur.
DO NOT leave the generator running in the manual mode
unattended.
NEVER operate this equipment under the influence or
drugs or alcohol.
Refer to the VOLVO Engine Owner's Manual for engine
technical questions or information.
ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children.
■
■
■
NEVER use accessories or attachments, which are not
recommended by MQ Power for this equipment.Damage
to the equipment and/or injury to user may result.
Manufacturer does not assume responsibility for any
accident due to equipment modifications. Unauthorized
equipment modification will void all warranties.
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
PAGE 10 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — RULES FOR SAFE OPERATION
Generator Grounding
DANGER - ELECTROCUTION HAZARDS
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground.
During operation of this generator, there
exists the possibility of electrocution,
electrical shock or burn, which can cause
severe bodily harm or even DEATH!
Article 250 (Grounding) of the National Electrical Code
(NEC) provides guide lines for proper grounding and specifies
that the cable ground shall be connected to the grounding
system of the building as close to the point of cable entry
as practical.
To avoid these hazards:
NEVER use damaged or worn cables when connecting
equipment to the generator. Make sure power connecting
cables are securely connected to the generator’s output
The following safety recommendations should also be
followed:
terminals, insufficient tightening of the terminal connections
WET
HANDS
may cause damage to the generator
■
■
■
ALWAYS make sure generator is properly grounded.
and electrical shock.
NEVER use gas piping as an electrical ground.
NEVER grab or touch a live power
ALWAYS make sure that electrical circuits are properly
grounded per the National Electrical Code (NEC) and
local codes before operating generator. Severe injury or
DEATH! by electrocution can result from operating an
ungrounded generator.
cord with wet hands.
POWER
CORD
(POWER ON)
NEVER touch output terminals
during operation. This is extremely
dangerous. ALWAYS stop the
machine and place the circuit
breaker in the OFF position when
contact with the output terminals is
required.
■
ALWAYS be sure to use the ground terminal (green wire)
when connecting a load to the U,V, and W output
terminal lugs.
Electrical Safety
Backfeed to a utility system can
cause electrocution and or property
damage. DO NOT connect to any
building's electrical system except
through an approved device or after
building main switch is opened.
ALWAYS have a licensed electrician
perform the installation
■
ALWAYS have a qualified electrician perform the
generator wiring installation.
■
ALWAYS make sure generator installation is accordance
with the National Electrical Code (NEC) and local codes
before operating generator.
■
■
■
NEVER use a defective or frayed power cable. Check
the cable for cuts in the insulation.
NEVER use a extension cord that is frayed or damaged
where the insulation has been cut.
ALWAYS make certain that proper extension cord has
been selected for the job. See Table 6.
■
■
NEVER power cables or cords lay in water.
NEVER stand in water while AC power from the generator
is being transfer to a load.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSVU — RULES FOR SAFE OPERATION
Maintenance Safety
Battery Safety
■
The electrical voltage required to operate the generator Use the following guidelines when handling the battery:
can cause severe injury or even death through physical
contact with live circuits. Turn all circuit breakers OFF
■
■
The battery contains acids that can
cause injury to the eyes and skin. To
avoid eye irritation, always wear safety
glasses.
before performing maintenance on the generator.
■
■
■
■
NEVER lubricate components or attempt service on a
running machine.
Use well insulated gloves when picking up the battery.
ALWAYS disconnect the NEGATIVE battery terminal
before performing service on the generator.
DANGER - EXPLOSION HAZARDS
Follow all Battery Safety Guidelines listed in this manual
when handleing or servicing the generator.
The risk of an explosion exists when performing service
on the battery. To avoid severe injury or DEATH:
ALWAYS allow the machine a proper amount of time to
cool before servicing.
■
DO NOT drop the battery.There
is the possibility of risk that the
battery may explode.
■
■
Keep the machinery in proper running condition.
Fix damage to the machine immediately and always
replace broken parts.
■
DO NOT expose the battery to
open flames, sparks, cigarettes
etc.The battery contains combustible gases and liquids.
If these gases and liquids come in contact with a flame
or spark, an explosion could occur.
■
ALWAYS service air cleaner frequently to prevent engine
malfunction.
WARNING - BURN HAZARDS
■
ALWAYS keep the battery charged. If the battery is not
To prevent burns, DO NOT touch or open any of the below
mentioned components while the engine is
running or immediately after operations.
Always allow sufficient time for the engine
and generator to cool before performing
maintenance.
charged a buildup of combustible gas will occur.
■
■
ALWAYS keep battery charging and cables in good
working condition. Repair or replace all worn cables.
ALWAYS recharge the battery in an vented air
environment, to avoid risk of a dangerous concentration
of combustible gases.
■
Radiator Cap - Removing the radiator cap while the
engine is hot will result in high pressurized, boiling water
to gush out of the radiator, causing severe scalding to
any persons in the general area of the generator.
■
■
In case the battery liquid (dilute sulfuric acid) comes in
contact with clothing or skin, rinse skin or clothing
immediately with plenty of water.
In case the battery liquid (dilute sulfuric acid) comes in
contact with your EYES, rinse eyes immediately with
plenty of water and contact the nearest doctor or hospital
to seek medical attention.
■
Coolant Drain Plug - Removing the coolant drain plug
while the engine is hot will result in hot coolant gushing
out of the coolant drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
■
Engine Oil Drain Plug - Removing the engine oil drain
plug while the engine is hot will result in hot oil gushing
out of the oil drain plug, therefore causing severe
scalding to any persons in the general area of the
generator.
PAGE 12 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-400SSVU — RULES FOR SAFE OPERATION
Towing &Transporting Safety
■
The maximum speed for highway towing is 55 MPH
unless posted otherwise. Recommended off-road towing
is not to exceed 15 MPH or less depending on type of
terrain.
To reduce the possibility of an accident while transporting
the generator on public roads, always make sure the trailer
that supports the generator and the towing vehicle are in
good operating condition and both units are mechanically
sound.
■
■
■
Place chock blocks underneath wheel to prevent rolling,
while parked.
The following list of safety precautions should be followed
when towing your generator:
Use the trailer’s swivel jack to adjust the trailer height to
a level position while parked.
Avoid sudden stops and starts.This can cause skidding,
or jack-knifing. Smooth, gradual starts and stops will
improve towing.
CAUTION - FOLLOWTOWING REGULATIONS
Check with your local county or state safety towing
regulations, in addition to meeting Department of
Transportation (DOT) SafetyTowing Regulations, before
towing your generator.
■
■
Avoid sharp turns.
Trailer should be adjusted to a level position at all times
when towing.
■
■
Raise and lock trailer wheel stand in up position when
transporting.
■
■
■
ALWAYS shutdown engine before transporting.
Tighten both fuel tank caps securely.
The maximum speed for highway towing is 55 MPH
unless posted otherwise. Recommended off-road towing
is not to exceed 15 MPH or less depending on type of
terrain.
If generator is mounted on a trailer, make sure trailer
complies with all local and state safety transportation
laws. Follow the listed Towing & Transporting Safety
guidelines for basic towing techniques.
■
Place support blocks underneath the trailer’s bumper to
prevent tipping, while parked.
■
Make sure the hitch and coupling of the towing vehicle
are rated equal to, or greater than the trailer "gross vehicle
weight rating.”
■
■
Avoid sharp turns to prevent rolling.
DO NOT transport generator with fuel in tank.
■
■
ALWAYS inspect the hitch and coupling for wear. NEVER
tow a trailer with defective hitches, couplings, chains etc.
Emergencies
■
■
■
ALWAYS know the location of the
nearest fire extinguisher.
Check the tire air pressure on both towing vehicle and
trailer. Trailer tires should be inflated to 50 psi cold.
Also check the tire tread wear on both vehicles.
ALWAYS know the location of the
nearest and first aid kit.
■
■
■
ALWAYS make sure the trailer is equipped with a "Safety
Chain".
ALWAYS know the location of the
nearest phone or keep a phone on
the job site, in case of emergencies.
ALWAYS attach trailer’s safety chains to towing vehicle
properly.
■
ALWAYS have easy access to the phone
numbers of the nearest Ambulance, Doctor
and Fire Department. This information will
be invaluable in the case of an emergency.
ALWAYS make sure the vehicle and trailer directional,
backup, brake, and trailer lights are connected and
working properly.
■
DOT Requirements include the following:
z
z
Connect and test electric brake operation.
Secure portable power cables in cable tray with tie
wraps.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERATOR DECALS
The DCA-300SSK generator is equipped with a number of safety decals (Figures 2 & 3). These decals are provided for
operator safety and maintenance information. The illustration below and on the preceding pages show the decals as they
appear on the machine. Should any of these decals become unreadable, replacements can be obtained from your dealer.
Figure 2. Generator Decals
PAGE 14 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERATOR DECALS
Figure 3. Generator Decals
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — INSTALLATION
Figure 4. Typical Generator Grounding Application
PAGE 16 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — INSTALLATION
Generator Grounding
Outdoor Installation
To guard against electrical shock and possible damage to
the equipment, it is important to provide a good EARTH
ground.
Install the generator in a area that is free of debris,
bystanders, and overhead obstructions. Make sure the
generator is on secure level ground so that it cannot slide or
shift around. Also install the generator in a manner so that
the exhaust will not be discharged in the direction of nearby
homes.
Article 250 (Grounding) of the National Electrical Code (NEC)
provides guide lines for proper grounding and specifies that
the cable ground shall be connected to the grounding system
of the building as close to the point of cable entry as
practical.
The installation site must be relatively free from moisture
and dust. All electrical equipment should be protected from
excessive moisture. Failure to do will result in deterioration
of the insulation and will result in short circuits and grounding.
NEC articles 250-64(b) and 250-66 set the following
grounding requirements:
Foreign materials such as dust, sand, lint and abrasive
materials have a tendency to cause excessive wear to
engine and alternator parts.
1. Use one of the following wire types to connect the
generator to earth ground.
a. Copper - 10 AWG (5.3 mm2) or larger.
b. Aluminum - 8 AWG (8.4 mm2) or larger.
CAUTION - EXHAUST HAZARD
2. When grounding the generator (Figure 3) connect the
ground cable between the lock washer and the nut on
the generator and tighten the nut fully.Connect the other
end of the ground cable to earth ground.
Pay close attention to ventilation when operating the
generator inside tunnels and caves. The engine exhaust
contains noxious elements. Engine exhaust must be routed
to a ventilated area.
3. NEC article 250-52(c) specifies that the earth ground
rod should be buried aminimum of 8 ft. into the ground.
Indoor Installation
Exhaust gases from diesel engines are extremely poisonous.
Whenever an engine is installed indoors the exhaust fumes
must be vented to the outside.The engine should be installed
at least two feet from any outside wall. Using an exhaust
pipe which is too long or too small can cause excessive
back pressure which will cause the engine to heat excessively
and possibly burn the valves.
When connecting the generator to
any buildings electrical system
ALWAYS consult with a licensed
NOTE
electrician.
Mounting
The generator must be mounted on a solid foundation (such
as concrete) and set firmly on the foundation to isolate
vibration of the generator when it is running. The generator
must set at least 6 inches above the floor or grade level (in
accordance to NFPA 110, Chapter 5-4.1). DO NOT remove
the metal skids on the bottom of the generator. They are to
resist damage to the bottom of the generator and to maintain
alignment.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERAL INFORMATION
Open Delta Excitation System
DCA-300SSK FAMILIARIZATION
Generator
The DCA-300SSK series generators are equipped with the
state of the art "Open-Delta" excitation system. The open
delta system consist of an electrically independent winding
wound among stationary windings of the AC output section.
The MQ Power DCA-300SSK series generators are 240 kW
generators that are designed as a high quality portable
(requires a trailer for transport) power source for telecom
sites, lighting facilities, power tools, submersible pumps and
other industrial and construction machinery.
There are four leads: A, B, C and D. During light loads, the
power to the AutomaticVoltage Regulator (AVR) is supplied
from the leads parallel connections of B&C. When loads
increase, the AVR switches and accepts power from leads
A&D. The output of leads A&D increase proportionally with
load. This of adding the voltages to each phase provides
better voltage response during heavy loads.
Engine Control Panel
The “Engine Control Panel ” is provided with the following:
z
z
z
z
z
z
z
z
z
z
z
z
z
Tachometer
Throttle Handle (Up to S/N 3701673)
WaterTemperature Gauge
Oil Pressure Gauge
Charging Ammeter Gauge
Engine Warning Display Module
Engine Speed Switch (S/N 3701674~)
Pre-Heat Button
Pre-Heat Lamp
Emergency Stop Button
Battery Switch
The connections of the AVR to the AC output windings are
for sensing only. No power is required from these windings.
The open-delta design provides virtually unlimited excitation
current, offering maximum motor starting capabilities. The
excitation does not have a "fixed ceiling" and responds
according the demands of the required load.
Engine
The DCA-300SSK is powered by a 4 cycle, water cooled,
turbocharged KOMATSU Model SA6D125E-2 diesel engine.
The DCA-300SSK2 and DCA-300SSK3 are powered by a 4
cycle, water cooled, air to air after cooled, turbocharged
KOMATSU Model SAA6D125E-2 diesel engine. These
engines are designed to meet every performance requirement
for the generator.ReferenceTable 2 for engine specifications.
Auto On/Off Engine Controller (S/N 3701674~)
Ignition Switch (Up to S/N 3701673)
Generator Control Panel
The “Generator Control Panel ” is provided with the following:
z
z
z
z
z
z
z
z
z
Output Voltage Adjustment Knob
Frequency Meter (Hz)
AC Ammeter (Amps)
AC Voltmeter (Volts)
Ammeter Change-Over Switch
Voltmeter Change-Over Switch
Panel Light
In keeping with Multiquip's policy of constantly improving its
products, the specifications quoted herein are subject to
change without prior notice.
The basic controls and indicators for the DCA-300SSK series
generators are addressed on the following pages.
Panel Light Switch
Pilot Lamp
Electronic Governor System
The DCA300SSK2 is equipped with an electronic governor
system. It is made up of two parts; an electronic controller
that monitors frequency variation as the load increases and
decreases, and an electronic actuator that controls the engine
throttle. Thr frequency is regulated at 0.25 to help protect
sensitive equipment.
Output Terminal Panel
The “OutputTerminal Panel ”is provided with the following:
z
z
z
z
3 auxiliary 240/139V output receptacles, 50 amp
3 auxiliary circuit breakers 240V @50 amps
2 120V GFCI receptacles, 20 amp
2 GFCI circuit breakers 120V@ 20amps
Microprocessor Engine Control (MPEC)
Control Box
The DCA300SSK3 incorporates the use of a microprocessor
engine controller unit (MPEC), which monitors basic engine
functions and also allows the generator to operate in an
unattended mode.
The “Control Box ” is provided with the following:
z
z
Main Circuit Breaker 800 amps
Over-Current Relay
PAGE 18 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — MAJOR COMPONENTS
Figure 5. Major C
Table 4. Generator Major Components
ITEM NO.
DESCRIPTION
Muffler Assembly
1
2
3
4
5
6
7
8
9
Engine Assembly
Enclosure Assembly
Generator Assembly
Output Terminal Assembly
Battery Assembly
Fuel Tank Assembly
Generator Control Panel Assembly
Engine Operating Panel Assembly
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — GENERATOR CONTROL PANEL
S/N 3701673 and Below
S/N 3701674 and Above
Figure 6. Generator Control Panel
PAGE 20 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — GENERATOR CONTROL PANEL
The definitions below describe the controls and functions of
the DCA-300SSK “Control Panel” (Figure 8).
During cranking cycle , The MPEC will attempt to crank the
engine for 10 seconds before disengaging. If the engine
does not engage (start) by the third attempt, the engine will
be shutdown by the engine controller’s " Over Crank
Protection" mode. If the engine engages at a speed (RPM's)
that is not safe, the controller will shutdown the engine by
initializing the "Over Speed Protection" mode.
1. Pilot Lamp – Indicates that the generator is working
properly.
2. Panel Light – Normally used in dark areas or at night
time.When activated, panel lights will illuminate.When
the generator is not in use be sure to turn the panel
light switch to the OFF position.
Also the engine controller will shutdown the generator in the
event of low oil pressure, high coolant temperature, low
coolant level, and loss of magnetic pickup.These conditions
can be observed by monitoring the LED status indicators on
the front of the controller module.
3. Frequency Meter – Indicates the output frequency in
hertz (Hz). Normally 60 Hz 1 Hz .
4. AC Ammeter – Indicates the amount of current the
load is drawing from the generator.
A. Off/Manual/Auto Switch – This switch controls the
running of the generator.If this switch is left in the "OFF"
position, the generator will not run. When this switch is
set to the manual position, the generator will start
immediately. If the generator is to be connected to a
building's AC power source via a transfer switch
(isolation), place the switch in the auto position. In this
position the generator will monitor the AC line output
from the building's power source.
5. AC Voltmeter – Indicates the single phase output
voltage present at the UVWO terminals.
6. Ammeter Change-Over Switch – This switch allows
the AC ammeter to indicate the current flowing to the
load connected to any phase of the output terminals,
or to be switched off.
7. Voltmeter Change-Over Switch – This switch allows
the AC voltmeter to indicate phase to phase voltage
between any two phases of the output terminals or to
be switched off.
B. Low Oil Pressure – Indicates the engine pressure
has fallen below 15 psi. The oil pressure is detected
using variable resistive values from the oil pressure
sending unit. This is considered a major fault.
8. Panel Light Switch – When activated will turn on control
panel light.
C. High Coolant Temperature – Indicates the engine
temperature has exceeded 215°F. The engine
temperature is detected using variable resistive values
from the temperature sending unit.This is considered a
major fault.
9. Voltage Regulator Control – Allows manual
adjustment of the generator’s output voltage.
10. MicroprocessorEngineController(MPEC S/N3701674~)
This controller has a vertical row of status LED's (inset),
that when lit, indicate that an
D. Overcrank Shutdown – Indicates the unit has
attempted to start a pre- programmed number of times,
and has failed to start.The number of cycles and duration
are programmable.Typical programmable start settings
is 3 cycles with a 10 second duration .This is considered
a major fault.
engine malfunction (fault), has
been detected. When a fault
has been detected the engine
controller will evaluate the
fault. Any major fault will
cause the controller to
shutdown the generator.
E. Overspeed Shutdown – Indicates the engine is running
at an unsafe speed. This is considered a major fault.
F. Engine Running – Indicates that engine is running at
a safe operating speed.
11. Main Circuit Breaker – This three-pole, 800 amp main
breaker is provided to protect the UVWO voltage output
terminals from overload.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — ENGINE OPERATING PANEL
S/N 3701673 and Below
Figure 7. Engine Operating Panels
PAGE 22 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — ENGINE OPERATING PANEL
4. Oil Pressure Gauge – During normal operation this
gauge be should read in the “GREEN” zone. When
starting the generator the oil pressure mar read a little
bit higher, but after the engine warms up the oil pressure
should return to the green zone.
The definitions below describe the controls and functions of
the DCA-300SSK or DCA-300SSK2 “Engine Operating
Panels” (Figure 7).
1. Throttle Handle - This handle controls the speed of
the engine (low or high).
5. WaterTemperature Gauge – During normal operation
2. Tachometer – Indicates engine speed in RPM’s for 60
Hz operation. This meter should indicate 1800 RPM’s
when the rated load is applied. In addition a built in hour
meter will record the number of operational hours that
the generator has been in use.
this gauge be should read in the “GREEN” zone.
6. Charging Ammeter Gauge – Indicates the current
being supplied by the engine’s alternator which provides
current for generator’s control circuits and battery
charging system.
3. Engine Warning Display Module – This module
7. Fuel Gauge - Indicates amount of diesel fuel available.
display’s the following engine failures:
8. Pre-Heat Lamp – Indicates that the glow plugs of the
diesel engine are hot and the engine is ready to be
started.
A. Overheat Lamp – This lamp goes ON when
the cooling water temperature rises
abnormally. If the lamp goes ON during
normal operation of the generator, the
emergency shutdown device will stop the
engine automatically.
9. Pre-Heat Button – Press and hold this button until the
preheat lamp is lit (ON).
10. Emergency Stop Button – Push this button inward to
stop the engine in the event of an emergency. DO NOT
use this button as a means of stopping the engine.
B. Low Oil Pressure Lamp – During normal
operation of the generator this lamp should
remain OFF. When the Auto-OFF/Reset-
Manual switch is set to the “Manual”
position to start the engine, the lamp will
11. Ignition Switch (Up to S/N3701673) – Four position
switch, pre-heat, stop, run and start. Insert ignition
key to start and stop engine.
be lit. After the oil pressure rises after start-
up the lamp will go OFF. If this lamp is ever lit (ON)
during normal operation of the generator, the emergency
shutdown device will stop the engine automatically.
12. Battery Switch – This switch should be set to the ON
position during normal operation.When the engine has
been stop, place this switch in the OFF position. DO
NOT turn this switch during normal operation, it could
cause damage to the electrical equipment.
C. Low Fuel Level Lamp – When this lamp is
ON, it is time to stop the engine and add
fuel. Remember to let the engine cool before
adding fuel.
13. Engine Speed Switch (S/N3701674~) – Changes
the speed of the engine rpm’s (low or high).
D. Low Battery Fluid Lamp – This lamp goes
ON when the battery fluid is low.If this lamp
goes ON during normal operation of the
generator, stop the engine and fill the
battery with distilled water to the specified
level.
E. Clogged Air Filter Lamp – This lamp goes
ON when the air filter is clogged. If this lamp
goes ON during normal operation of the
generator, stop the engine and replace the
air filter.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — OUTPUT TERMINAL PANEL FAMILIARIZATION
Output Terminal Familiarization
Output Terminal Panel
Shown below (Figure 8) is the Output Terminal Panel , lift
up on the cover to gain access to receptacles and terminal
lugs.
The “Output Terminal Panel ” (Figure 8) is provided with
the following:
z
z
z
z
z
Three 240/139V output receptacles, 50 amp
Three circuit breakers 240V @50 amps
Two 120V GFCI receptacles, 20 amp
Two (2) GFCI circuit breakers 120V@ 20 amps
Eight (8) output terminal lugs
Terminal legs “O” and “Ground”
NOTE
are considered bonded grounds.
Figure 8. Outpu
PAGE 24 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — OUTPUT TERMINAL PANEL FAMILIARIZATION
Each auxiliary receptacle is protected by a 50 amp circuit
breaker.These breakers are located directly above the GFCI
receptacles. Remember the load output (current) on all three
receptacles is dependent on the load requirements of the
UVWO terminals.
120VAC GFCI Receptacles
There are two 120VAC, 20 amp GFCI (Duplex Nema 5-20R)
recepacles provided on the output terminal panel. These
receptacles can be accessed in any voltage change-over
board position. Each receptacle is protected by a 20 amp
circuit breaker. These breakers are located directly above
the GFCI receptacles. Remember the load output (current)
of both GFCI receptacles is dependent on the load
requirements of the UVWO terminals.
Turn the voltage regulator control knob (Figure 11) on the
control panel to obtain the desired voltage.Turning the knob
clockwise will increase the voltage, turning the knob counter-
clockwise will decrease the voltage.
Pressing the reset button resets the GFCI receptacle after
being tripped. Pressing the "Test Button" (See Figure 9) in
the center of the receptacle will check the GFCI function.
Both receptacles should be tested at least once a month.
Figure 11. Voltage Regulator Control Knob
Figure 9. G.F.C.I. Receptacle
Twist Lock DualVoltage 240/139VAC Receptacles
There are three 240/139 VAC, 50 amp auxiliary twist-lock
(CS-6369) receptacles (Figure 10) provided on the output
terminal panel. These receptacles can be accessed in any
voltage change-over board position.
Figure 10. 240/139 VAC Twist-Lock
Auxiliary Receptacles
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — OUTPUT TERMINAL PANEL FAMILIARIZATION
Connecting Loads
Over Current Relay
Loads can be connected to the generator by the UVWO terminal
lugs or the convenience receptacles. (See Figure 12). Make
sure to read the operation manual before attempting to connect
a load to the generator.
An over current relay (Figure 13) is connected to the main
circuit breaker. In the event of an overload, both the circuit
breaker and the over current relay may trip. If the circuit
breaker can not be reset, the reset button on the over cur-
rent relay must be pressed. The over current relay is lo-
cated in the control box.
To protect the UVWO output terminals from overload, a 3-
pole, 800 amp, main circuit breaker is provided. Make sure
to switch ALL circuit breakers to the "OFF" position prior to
starting the engine.
Figure 13. Over Current Relay
Maximum Power Output (KW)
The entire load connected to the UVWO output terminal lugs,
duplex and auxiliary receptacles must not exceed 264 kw in
standby or 240 kw in prime output.
Figure 12. Connecting Loads
PAGE 26 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — LOAD APPLICATION
Single Phase Load
Three Phase Load
When calculating the power requirements for 3-phase power
use the following equation:
Always be sure to check the nameplate on the generator
and equipment to insure the wattage, amperage and
frequency requirements are satisfactorily supplied by the
generator for operating the equipment.
Generally, the wattage listed on the nameplate of the
equipment is its rated output. Equipment may require 130—
150% more wattage than the rating on the nameplate, as
the wattage is influenced by the efficiency, power factor and
starting system of the equipment.
Motors and motor-driven
equipment draw much greater
current for starting than during
operation.
NOTE
If wattage is not given on the equipment's
name plate, approximate wattage may be
determined by multiplying nameplate
voltage by the nameplate amperage.
An inadequate size connecting cable which cannot carry the
required load can cause a voltage drop which can burn out
the appliance or tool and overheat the cable. See Table 6.
WATTS = VOLTAGE x AMPERAGE
z
z
z
When connecting a resistance load such as an
incandescent lamp or electric heater, a capacity of up to
the generating set’s rated output (kW) can be used.
The power factor of this generator is 0.8. See Table 5 below
when connecting loads.
When connecting a fluorescent or mercury lamp, a
capacity of up to the generating set’s rated output (kW)
multiplied by 0.6 can be used.
Table 5. Power Factor By Load
Type Of Load
Power Factor
Single-phase induction motors
0.4 - 0.75
When connecting an electric drill or other power tools,
pay close attention to the required starting current
capacity.
Electric heaters, incandescent
lamps
1.0
0.4 - 0.9
1.0
Fluorescent lamps, mercury lamps
When connecting ordinary power tools, a capacity of up to
the generating set’s rated output (kW) multiplied by 0.8 can
be used.
Electronic devices, communication
equipment
Common power tools
0.8
DANGER - ELECTRICAL SYSTEM HAZARDS
Table 6. Cable Selection (60 Hz, Single Phase Operation)
Load In Watts Maximum Allowable Cable Length
Before connecting this generator to any building’s electrical
system, a licensed electrician must install an isolation
(transfer) switch. Serious damage to the building’s
electrical system may occur without this transfer switch.
Current in
Amperes
At 120
Volts
At 240
Volts
#10 Wire
#12 Wire
#14 Wire
#16 Wire
2.5
5
300
600
600
1000 ft.
500 ft.
350 ft.
250 ft.
150 ft.
125 ft.
600 ft.
300 ft.
200 ft.
150 ft.
100 ft.
75 ft.
375 ft.
200 ft.
125 ft.
100 ft.
65 ft.
250 ft.
125 ft.
100 ft.
1200
1800
2400
3600
4800
7.5
10
15
20
900
If 3Ø load (kVA) is not given on
the equipment nameplate,
approximate 3Ø load output
1200
1800
2400
NOTE
maybedeterminedbymultiplying
voltage by amperage by 1.732.
50 ft.
CAUTION: Equipment damage can result from low voltage.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERATOR OUTPUTS
Generator OutputVoltages
Generator Amperage
Tables 8 and 9 describe the generator’s current output capa-
bility for both 1Ø-phase and 3Ø phase applications.
A wide range of voltages are available to supply voltage for
many different applications. Voltages are selected by apply-
ing jumpers (6) to the voltage change-over board (Figure 14).
To obtain some of the voltages as listed in Table 7 (see
below) will require a fine adjustment using the voltage regu-
lator (VR) control knob located on the control panel.
Table 8. Generator Ampere Ratings
⎯
1∅
kW
20
139V
144
240V
83
277V
480V
42
72
Voltage Change-Over Board
40
288
167
250
333
417
500
583
667
750
833
917
1000
144
217
289
361
433
505
578
650
722
794
866
83
The voltage change-over board (Figure 14) is located on
the control box, behind the generator control panel. This
board has been provided for ease of voltage selection.
60
432
125
167
208
250
292
333
375
417
458
500
80
576
100
120
140
160
180
200
220
240 (Max)
719
863
1007
1151
1295
1439
1583
1727
Table 9. Generator Ampere Ratings
⎯
3∅
Figure 14. Voltage Change-Over Board
240V Configuration
KW
20
240V
60
480V
30
CAUTION - CHANGINGVOLTAGES
40
120
180
241
301
361
421
481
541
601
662
722
60
60
90
NEVER attempt to place jumper plates on the voltage
change-over board while the generator is in operation.
There exist the possibility of electrocution, electrical
shock or burn, which can cause severe bodily harm
or even death!
80
120
150
180
210
241
271
301
331
361
100
120
140
160
180
200
220
240
Table 7. Generator Available Voltages
Three-Phase
208V
220V
240V
416V
440V
480V
277V
Single-Phase 120V
127V
139V
240V
254V
PAGE 28 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERATOR OUTPUTS/GAUGE READING
Maximum Amps
Table 10 shows the maximum amps the generator can pro-
vide. DO NOT exceed the maximum amps as listed.
Table 10. Generator Maximum Amps
DCA300SSK
Model:
Series
Rated Voltage
Maximum Amps
2000 amps (4 wire)
1000 amps (4 wire)
720 amps
Single Phase
120 Volt
Single Phase
240 Volt
Figure 17. AC Voltmeter
Gauge
(Volt reading on W-U Lug)
Figure 16. AC Voltmeter
Change-Over Switch
Three Phase
240 Volt
Three Phase
480 Volt
360 amps
40
20
60
How to Read the OutputTerminal Gauge.
0
75
The AC ammeter and AC voltmeter change-over switches
on the control panel DO NOT effect the generator output.
They are provided to help observe how much power is being
supplied, produced at the UVWO terminals lugs.
A
When the voltage change-over board is jumpered for 3Ø,
240V operation (See Figure 15), place the AC Voltmeter
Change-Over Switch (Figure 16) to the W-U position and
the AC Ammeter Change-Over Switch (Figure 18) to the U
or W position to read the output on the selected leg.
Figure 18. AC Ammeter
Change-Over Switch
Figure 19. AC Ammeter
(Amp reading on U lug)
The ammeter and voltmeter
gauges are only active when the
UVWO terminals are in use.
NOTE
Figure 15. Voltage Change-Over Board
240V Configuration
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — OUTPUT TERMINAL PANEL CONNECTIONS
UVWO Terminal Output Voltages
Various output voltages can be obtained using the UVWO
output terminal lugs. The voltages at the terminals are de-
pendent on the placement of the jumpers plates (6) on the
Voltage Change-Over Board and the adjustment of the
Voltage Regulator Control Knob.
Figure 22. Voltage Regulator Knob
Remember the voltage change-over board determines the
range of the output voltage and can be configured in two
different positions that provide 6 different output voltages at
the UVWO output terminals. The generator is shipped from
the factory in the 240V configuration. The voltage regulator
(VR) allows the user to increase or decrease the selected
voltage.
1Ø-240V UVWOTerminal Output Voltages
1. Make sure the voltage change-over board is jumpered
for 240V operation as shown in Figure 20 .
2. Connect the load wires to the UVWO terminals as shown
in Figure 23.
3Ø-240V UVWOTerminal Output Voltages
1. Jumper the voltage change-over board for 240V operation
as shown in Figure 20.
Figure 23. UVWO Terminal Lugs
1Ø-240V Connections
Figure 20. Voltage Change-Over Board
240V Configuration
1Ø-139V UVWOTerminal Output Voltages
1. Make sure the voltage change-over board is jumpered
for 240V operation as shown in Figure 20.
2. Connect the load wires to the UVWO terminals as shown
in Figure 21.
2. Connect the load wires to the UVWO terminals as shown
in Figure 24.
Figure 21. UVWO Terminal Lugs
3Ø-240V Connections
3. Turn the voltage regulator knob (Figure 22) clockwise to
increase voltage output, turn counterclockwise to
decrease voltage output. Use voltage regulator
adjustment knob whenever fine tuning of the output
voltage is required
Figure 24. UVWO Terminal Lugs
1Ø-139V Connections
PAGE 30 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — OUTPUT TERMINAL PANEL CONNECTIONS
3Ø-480V UVWOTerminal Output Voltages
1Ø-480V UVWOTerminal Output Voltages
1. Jumper the voltage change-over board for 480V operation 1. Make sure the voltage change-over board is jumpered
as shown in Figure 25.This configuration uses 6 jumper
plates in 3 different positions. Remember there are 2
jumper plates at every position. Every jumper plate must
be used.
for 480V operation as shown in Figure 25.
2. Connect the load wires to the UVWO terminals as shown
in Figure 27.
Figure 25. Voltage Change-Over Board
480V Configuration
Figure 27. UVWO Terminal Lugs
1Ø-480V Connections
2. Connect the load wires to the UVWO terminals as shown
in Figure 26.
1Ø-277V UVWOTerminal Output Voltages
1. Make sure the voltage change-over board is jumpered
for 480V operation as shown in Figure 25.
2. Connect the load wires to the UVWO terminals as shown
in Figure 28.
Figure 26. UVWO Terminal Lugs
3Ø-480V Connections
Figure 28. UVWO Terminal Lugs
1Ø-277V Connections
ALWAYS make sure that the
connections to the UVWO
NOTE
terminals are secure and tight.
The possibility of arcing exists,
that could cause a fire.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — PRE-SETUP
Fuel Check
Circuit Breakers
To protect the generator from an overload, a 3-pole, 800 amp,
main circuit breaker is provided to protect the UVWO output
terminals from overload. In addition two single-pole, 20 amp
GFCI circuit breakers are provided to protect the GFCI
receptacles from overload.Three 50 amp load circuit breakers
have also been provided to protect the auxiliary receptacles
from overload. Make sure to switch ALL circuit breakers to
the "OFF" position prior to starting the engine.
DANGER - EXPLOSION/FIRE HAZARDS
Fuel spillage on a hot engine can cause a fire or explosion.
If fuel spillage occurs, wipe up the spilled fuel completely
to prevent fire hazards. NEVER smoke around or near the
generator.
Lubrication Oil
Fill the engine crankcase with lubricating oil through the filler
hole, but DO NOT overfill. Make sure the generator is level.
Also verify that the oil level is maintained between the two
notches (Figure 29) on the dipstick. See Table 11 for proper
selection of engine oil.
REFILLING THE FUEL SYSTEM
The DCA300SSK series generators may (if equipped with a
trailer or skid) have a double fuel tank system (Figure 30),
which consists of an internal generator fuel tank, and a
trailer mounted fuel tank. It is also possible the generator
can be equipped with a skid mounted fuel tank (Figure 31).
The skid type fuel system does not use the internal generator
fuel tank.
Use the instructions in this section that applies to your type
of fuel tank system.
Figure 29. Engine Oil Dipstick
When checking the engine oil, be sure to check if the oil is
clean. If the oil is not clean, drain the oil by removing the oil
drain plug, and refill with the specified amount of oil as outlined
in the Komatsu Engine Owner's Manual. Oil should be
warm before draining.
ALWAYS fill the fuel tank with clean and fresh #2 diesel
fuel. DO NOT fill the fuel tanks beyond their capacities.
Pay attention to the fuel tank capacity when replenishing
fuel. The fuel tank cap must be closed tightly after filling.
Handle fuel in a safety container. If the container does not
have a spout, use a funnel. Wipe up any spilled fuel
immediately.
Other types of motor oils may be substituted if they meet
the following requirements:
z
z
z
z
z
API Service Classification CH-4
API Service Classification CG-4
API Service Classification CF-4
ACEA Specification E3
ACEA Specification E2
Table 11. Recommended Motor Oil
Figure 30. Double Fuel Tank System
CAUTION - REFUELINGTHE GENERATOR
Temperature Range
Type Oil
77oF and greater
SAE15W-40 or SAE40
SAE 10W-30 or SAE30
SAE10W-30 or SAE10
(25oC and greater)
32oF to 77oF
(0oC to 25oC)
ONLY properly trained personel who have read and
understand this section should refill the fuel tank system.
-22oF to -32oF
(-30oC0oC)
PAGE 32 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — PRE-SETUP
CAUTION - REFUELINGTRAILER FUELTANK
ALWAYS! fill trailer tank first with #2 diesel fuel, before
filling secondary internal tank.
Figure 31. Skid Type Fuel Tank System
Refueling Procedure:
WARNING - RESPIRATORY HAZARDS
Diesel fuel and its vapors are dangerous
to your health and the surrounding
environment. Avoid skin contact and/or
inhaling fumes.
1. Level Tanks – make sure fuel cells are level with the
ground. Failure to do so will cause fuel to spill from the
tank before reaching full capacity. See Figure 32.
CAUTION - REFUELINGTHE GENERATOR
Figure 33. Fuel Tank Filling Order
ALWAYS place trailer on firm level ground before refueling
to prevent spilling and maximize the amount of fuel that
can be pumped into the tank.
ONLY! use #2 diesel fuel when
refueling.
NOTE
Fuel from the secondary inner
tank will eventually drain into the
primary trailer tank.
NOTE
Figure 32. Only Fill on Level Ground
2. Trailer Fuel Tank First – The trailer fuel tank is the
primary fuel tank and holds a larger capacity of fuel.
The fuel in the trailer will be filtered and sent to the
engine. ALWAYS fill trailer fuel tank (Figure 33) first.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — PRE-SETUP
3. NEVER overfill trailer fuel tank – It is important to
read the trailer fuel gauge when filling trailer fuel tank.
DO NOT wait for fuel to rise in filler neck. See Figure 34.
5. Figure 36 below reflects a full fuel system.
Figure 34. Full Trailer Tank
Figure 36. Full Fuel System
6. Fuel from the engine return line will drain into the secondary
internal fuel tank. This fuel will eventually drain into the
primary trailer tank in order to return to the engine.
CAUTION - REFUELINGTHE GENERATOR
DO NOT OVER-FILL fuel system. Leave room for fuel
expansion. Fuel expands when heated.
WARNING - REFUELING SECONDARY FUELTANK
It is recommended to only fill the internal secondary fuel tank to
3/4 full in order to allow for fuel return, fuel expansion, and to
avoid spillage. See Figure 37 for fuel expansion.
4. Once the trailer tank is full, the secondary inner tank
can be filled (See Figure 35). Notice how the trailer
filler tube level rises when the internal tank is filled.
Figure 37. Fuel Expansion
Figure 35. Filling Secondary Internal Fuel Tank
PAGE 34 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — PRE-SETUP
Coolant (Ethylane Glycol [Green] / Water — 50/50 mix)
Use only drinkable tap water. If hard water or water with
many impurities is used, the inside of the engine and radiator
may become coated with deposits and cooling efficiency
will be reduced.
When the antifreeze is mixed with
water, the antifreeze mixing ratio
must be less than 50%.
NOTE
Cleaning the Radiator
An anticorrosion additive added to the water will help prevent
deposits and corrosion in the cooling system. See the engine
manual for further details.
The engine may overheat if the radiator fins become
overloaded with dust or debris. Periodically clean the radiator
fins with compressed air. Cleaning inside the machine is
dangerous, so clean only with the engine turned off and the
negative battery terminal disconnected.
WARNING - BURN HAZARDS
If adding coolant/antifreeze mix to the
radiator, DO NOT remove the radiator cap
until the unit has completely cooled.The
possibility of hot! coolant exists which
can cause severe burns.
Air Cleaner
Periodic cleaning/replacement is necessary. Inspect it in
accordance with the Komatsu Engine Owner's Manual.
Fan Belt Tension
A slack fan belt may contribute to overheating, or to
insufficient charging of the battery. Inspect the fan belt for
damage and wear and adjust it in accordance with the
Komatsu Engine Owner's Manual.
Day-to-day addition of coolant is done from the recovery
tank. When adding coolant to the radiator, DO NOT remove
the radiator cap until the unit has completely cooled. See
Table 11 for engine and radiator, coolant capacities. Make
sure the coolant level in the recovery tank is always between
the "H" and the "L" markings.
The fan belt tension is proper if the fan belt bends 10 to 15
mm (Figure 38) when depressed with the thumb as shown
below.
Table 11. Coolant Capacity
Engine Type
Coolant Capacity
8.5 Gal. (32.6 Liters)
9.8 Gal. (37.0 Liters)
Komatsu SA6D125E-2
Komatsu SAA6D125E-2
Figure 38. Fan Belt Tension
CAUTION - ROTATING PARTS
Operation FreezingWeather
When operating in freezing weather, be certain the proper
amount of antifreeze (Table 12) has been added.
NEVER place hands near
the belts or fan while the
generator set is running.
Table 12. Anti-Freeze Operating Temperatures
Freezing Point
Boiling Point
Vol %
Anti-Freeze
°C
-24
-37
°F
°C
°F
40
50
-12
-34
106
108
222
226
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — PRE-SETUP
If the battery cable is connected
incorrectly, electrical damage to
the generator will occur. Pay close
attention to the polarity of the
battery when connecting the
battery.
Battery
This unit is of negative ground DO NOT connect in reverse.
Always maintain battery fluid level between the specified
marks. Battery life will be shortened, if the fluid level are not
properly maintained. Add only distilled water when
replenishment is necessary.
NOTE
DO NOT over fill. Check to see whether the battery cables
are loose. Poor contact may result in poor starting or
malfunctions. Always keep the terminals firmly tightened.
Coating the terminals with an approved battery terminal
treatment compound. Replace battery with only
recommended type battery.
CAUTION - BATTERY SERVICING SAFETY
Inadequate battery connections may cause poor starting
of the generator, and create other malfunctions.
Alternator
The battery is sufficiently charged if the specific gravity of
the battery fluid is 1.28 (at 68° F). If the specific gravity
should fall to 1.245 or lower, it indicates that the battery is
dead and needs to be recharged or replaced.
The polarity of the alternator is negative grounding type. When
an inverted circuit connection takes place, the circuit will be
in short circuit instantaneously resulting the alternator failure.
Battery Cable Installation
DO NOT put water directly on the alternator. Entry of water
into the alternator leads an electrolyte corrosion causing an
alternator failure.
ALWAYS be sure the battery cables (Figure 39) are properly
connected to the battery terminals as shown below. The
RED cable is connected to the positive terminal of the battery,
and the BLACK cable is connected to the negative terminal
of the battery.
Before charging the battery with an external electric source,
be sure to disconnect the battery cables.
Wiring
Inspect the entire generator for bad or worn electrical wiring
or connections. If any wiring or connections are exposed
(insulation missing) replace wiring immediately.
CAUTION - BATTERY SERVICING SAFETY
ALWAYS disconnect the negative terminal FIRST and
reconnect negative terminal LAST.
Piping and Hose Connection
Inspect all piping, oil hose, and fuel hose connections for
wear and tightness.Tighten all hose clamps and check hoses
for leaks.
If any hose (fuel or oil) lines are defective replace them
immediately.
If applicable perform the following:
Figure 39. Battery Connections
■
Apply commercial power to the internal battery charger
receptacle (to ensure good starting) via commercial power.
An external power cord will be required.This capability is an
option.
When connecting battery do the following:
1. NEVER connect the battery cables to the battery
terminals when the ignition switch is in either the Pre-
Heat, RUN, or START position. ALWAYS make sure
that the ignition switch is in the STOP position when
connecting the battery.
■
Apply commercial power to the jacket water heater
receptacle (not necessary for warm climates) via commercial
power.An external power cord will be required.This capability
is an option.
2. Place a small amount of battery terminal treatment
compound around both battery terminals.This will ensure
a good connection and will help prevent corrosion around
the battery terminals.
PAGE 36 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GEN. START-UP PROCEDURE (MANUAL)
BEFORE STARTING (S/N 3701673 and below)
1. Place the main, G.F.C.I. and aux. circuit breakers (Figure 42)
in the “OFF” position prior to starting the engine.
Steps 1 thru 20 are referenced
for Engine Operating Panel S/N
3701673 and below. See Figure
40 below. This unit has an igni-
tion switch and a throttle
handle.
NOTE
Figure 42. Main, Aux. and GFCI
Circuit Breakers (OFF)
2. Make sure the the voltage change-over board has
been configured for the desired output voltage.
3. Connect the load to the UVWO terminals or auxiliary
receptacles as shown in Figure 12. These load
connection points can be found on the output terminal
panel. To gain access to the UVWO terminals or other
power receptacles, unlock the access cover and lift the
door.
Figure 40. Engine Operating Panel
S/N 3701673 and Below
CAUTION - LETHAL EXHAUST HAZARD
The engine's exhaust contains harmful emissions.
ALWAYS have adequate ventilation when operating.
Direct exhaust away from nearby personnel.
4. Tighten terminal nuts securely to prevent load wires from
slipping out
5. Close all engine enclosure doors (Figure 42).
WARNING - STARTINGTHE GENERATOR
NEVER! manually start the engine with the main, GFCI
or auxiliary circuit breakers in the ON (closed) position.
Figure 42. Engine Enclosure Doors
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERATOR START-UP PROCEDURE (MANUAL)
6. Set the battery ON/OFF switch (Figure 43) to the “ON”
12. The generator's frequency meter (Figure 48) should be
position.
displaying the 60 cycle output frequency in HERTZ.
Figure 43. Battery ON/OFF Switch
Figure 48. Frequency Meter (Hz)
7. When starting the generator in COLD weather conditions,
turn the ignition key to the “PREHEAT ”position (Figure 44).
13. The generator's AC-voltmeter (Figure 49) will display the
generator’s output in VOLTS. If the voltage is not within
the specified tolerance, use the voltage adjustment
control knob (Figure 50) to increase or decrease the
desired voltage.
Figure 44. Ignition Switch (Pre-Heat)
8. Press and hold the engine preheat button (Figure 45)
until the preheat lamp is lit (ON).
Pre-Heat
Lamp
Pre-Heat
Button
Figure 49. Voltmeter
Figure 45. Pre-Heat Button/ Lamp
9. Place the engine throttle control in the “LOW” position
(Figure 46).
Figure 50. Voltage Adjust Control Knob
14. The ammeter (Figure 51) will indicate zero amps with no
load applied. When a load is applied, the ammeter will
indicate the amount of current that the load is drawing
from the generator.
Figure 46. Engine Throttle Control
10. Turn the ignition key to the “START” position (Figure 47)
and listen for the engine to begin cranking. After the
engine starts release the ignition key.
Figure 51. Ammeter (No Load)
Figure 47 Engine Ignition Switch
11. Once the engine has started, let it run for 3-5 minutes,
then turn the throttle handle control (Figure 46) to the
“HIGH” position.
PAGE 38 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERATOR START-UP PROCEDURE (MANUAL)
15. The engine oil pressure gauge (Figure 52) will indicate
the oil pressure (kg/ cm2) of the engine. Under normal
operating conditions the oil pressure is approximately
18. Place the main, GFCI, and aux. circuit breakers in the
“ON” position (Figure 55).
4
8
ENGINE OIL PRESSURE
kg/cm2
0
Figure 52. Oil Pressure Gauge
16. The coolant temperature gauge (Figure 53) will indicate
the coolant temperature. Under normal operating
conditions the coolant temperature should be between
165 and 215 degrees Fahrenheit (Green Zone).
Figure 55. Main, Aux. and GFCI
Circuit Breakers (ON)
19. Observe the generator's ammeter (Figure 56) and verify
it reads the anticipated amount of current with respect
to the load. The ammeter will only display a current
reading if a load is in use.
WATER TEMP
Figure 53. Coolant Temperature Gauge
17. The tachometer gauge (Figure 54) will indicate the
speed of the engine when the generator is operating.
Under normal operating conditions this speed is
approximately 1800 RPM’s.
Figure 56. Ammeter (Load)
20. The generator will run until manually stopped or an
abnormal condition occurs.
Figure 54. Engine Tachometer Gauge
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GENERATOR START-UP PROCEDURE (MANUAL)
BEFORE STARTING (S/N 3701674 and above)
4. Place the engine speed switch in the “LOW ” position
(Figure 60).
Steps 1 thru 8 are referenced
for Engine Operating Panel
S/N 3701674 and above. See
Figure 57 below.This unit does
not have an ignition switch or a
throttle handle. It does have an
“engine speed switch” that is
used in conjunction with the
MPEC unit.
NOTE
Figure 60. Engine Speed Switch (Low)
5. Place the Auto-Off/Reset-Manual switch in the “Manual”
position to start the engine (Figure 61). Once the engine
starts, let the engine run for 1-2 minutes. Listen for any
abnormal noises.
Figure 61. Auto-Off/Reset-Manual Switch
6. Once the engine is warm and the engineisrunningproperly,
place the engine speed switch in the “HIGH ” position
(Figure 62).
Figure 57. Engine Operating Panel
S/N 3701674 and Above
1. Before attempting to start generator, reference steps
1 thru 5 in the “Before Starting Section” for Engine
Operating Panel S/N 3701673 and below.
Figure 62. Engine Speed Switch (High)
2. Set the battery ON/OFF switch (Figure 58) to the “ON”
7. Verify that the "Engine Running" status LED on the MPEC
position.
unit (Figure 63) is "ON" (lit) after the engine has been started.
Figure 58. Battery ON/OFF Switch
3. Press and hold the engine preheat button (Figure 59)
until the preheat lamp is lit (ON).
Figure 63. Engine Running LED (ON)
Pre-Heat
Lamp
Pre-Heat
Button
8. Continue operating the generator as outlined in steps 11
thru 20 in the “Before Starting Section” for Engine
Operating Panel S/N 3701673 and below.
Figure 59. Pre-Heat Button/ Lamp
PAGE 40 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GEN. START-UP PROCEDURE (AUTO MODE)
Starting (Auto Mode)
When starting generator in AUTO mode use the "Manual
Start-up" procedure except where noted (see below).
DANGER - ELECTRICAL SYSTEM HAZARDS
1. Before attempting to start generator, reference steps
1 thru 5 in the “Before Starting Section” for Engine
Operating Panel S/N 3701673 and below.
Before connecting this generator to any
building’s electrical system, a licensed
electrician must install an isolation
(transfer) switch. Serious damage to the
building’s electrical system may occur
without this transfer switch.
2. Set the battery ON/OFF switch (Figure 64) to the “ON”
position.
CAUTION - BACKUP GENERATOR USE
When connecting the generator to a isolation (transfer)
switch, ALWAYS have power applied to the generator's
internal battery charger. This will ensure that the engine
will not fail due to a dead battery.
Figure 64. Battery ON/OFF Switch
3. Set the engine speed switch (Figure 65) to the “High”
position.
When the generator is set in the
AUTO mode, the generator will
automically start in the event of
comercial power falling below a
Figure 65. Engine Speed Switch (High)
NOTE
prescribed level by means of a
contact closure that is generated
automatically by a transfer switch.
4. Place the Off/Manual/Auto switch (Figure 66) on the
MPEC unit to the AUTO position.
WARNING - AUTO MODE MAINTENANCE
When running the generator in the AUTO mode, remember
the generator can start up at any time without warning.
NEVER attempt to perform any maintenance when the
generator is in the auto mode.
Figure 66. Off/Manual Auto Switch (AUTO)
5. Continue operating the generator as outlined in steps 11
thru 19 in the “Before Starting Section” for Engine
Operating Panel S/N 3701673 and below.
CAUTION - ENGINE SPEED SWITCH
The Engine Speed Switch must be set to the “High”
position when running in the Auto-Start mode.Failing to
set the switch in the proper position can result in damage
to your generator when it turns on.
When the MPEC Control Switch
is placed in the AUTO position,
the engine glow plugs will be
NOTE
warmed and the engine will start
automatically.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — GEN. SHUT-DOWN PROCEDURE (MANUAL)
Engine Shutdown Ignition Key (Up to S/N 3701673)
Engine Shutdown Controller (S/N 3701674~)
To shutdown the generator use the following procedure:
To shutdown the generator use the following procedure:
1. Place both the MAIN, GFCI and LOAD circuit breakers 1. Place both the MAIN, GFCI and LOAD circuit breakers
(Figure 67) to the "OFF position".
as shown in Figure 67 to the "OFF position".
2. Place the engine speed switch in the “LOW ” position
(Figure 71).
Figure 71. Engine Speed Switch (High)
3. Let the engine cool by running it for 3-5 minutes with no
load applied.
Figure 67. Main, Aux. and GFCI
Circuit Breakers (OFF)
4. Place the Auto-Manual/Off/Reset switch (Figure 72) to
the OFF/Reset position.
2. Place the throttle control (Figure 68) in the “LOW”position.
Figure 68. Engine Throttle Control
Figure 72. Auto-Manual Off/Reset Switch
3. Let the engine cool by running it for 3-5 minutes with no
load applied.
4. Place the ignition key (Figure 69) in the “STOP” position.
5. Verify that the all status LED on the MPEC display are
"OFF" (not lit).
6. Remove all loads from the generator.
WARNING - SHUTTING DOWNTHE GENERATOR
Figure 69. Ignition Key Switch (STOP position)
NEVER stop the engine suddenly except in an emergency.
DO NOT use the emergency stop switch a as method of
shutting down the generator. This switch is ONLY to be
used in the event of an emergency.
5. Remove all loads from the generator.
Emergency Shutdown Procedure
1. PUSH inward the RED emergency stop button located
on the engine operating panel (Figure 70) to turn off
the generator in the event of an emergency.This button
is located on either Engine Operating Panel.
To disengage the emergency
stop function, pull the
emergency stop button outward
NOTE
to its original position. This will
allow the generator to operate
normally. Remember the
generator will not start if the emergency stop button is
engaged.
Figure 70. Emergency Stop Button
PAGE 42 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — MAINTENANCE
Use Table 13 shown below as a general checklist to be
performed on a daily basis.
10 Hrs
DAILY
250 Hrs
500 Hrs
1000 Hrs
TABLE 13. INSPECTION / MAINTENANCE
Check Engine Fluid Levels
Check Fuel Filter
X
X
X
X
X
Check Air Cleaner Dust Indicator
Check for Leaks/Visual Walk Around
Check for Loosening of Parts
Replace Engine Oil and Filter *1
Service Battery
X
X
X
ENGINE
Clean Unit, Inside and Outside
Change Fuel Filter *2
X
X
Clean Radiator and Check Coolant
Protection Level
Replace Air Filter Element
Test Thermostats
X
X
X
X
Check all Hoses and Clamps/Flush Radiator
Clean Inside of Fuel Tank
Measure Insulation Resistance Over 3M
ohms
X
GENERATOR
1
*
*
Replace engine oil anf filter at 100 hours, first time only.
Replace fuel filter at 250 Hours, first time only.
2
PAGE 44 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — MAINTENANCE
General Inspection
Fuel Addition
Prior to each use, the generating set should be cleaned and Add diesel fuel (the grade may vary according to season
inspected for deficiencies. Check for loose, missing or and locations). Always pour through the mesh filter.
damaged nuts, bolts or other fasteners. Also check for fuel
or oil leaks.
Air Cleaner
Every 50 hours:If dust indicator is RED, clean the air cleaner
element.
Removing Water from the Tank
After prolonged use, water and other impurities accumulate
in the bottom of the tank. Occasionally remove the drain
cock and drain the contents. During cold weather, the greater
the empty volume inside the tank, the easier it is for water to
Outer Element:
condense. This can be reduced by always keeping the tank
as full as possible.
1. Loosen wing bolt, remove dust cup, then remove wing
nut and take out element.
Air Removal
If air enters the fuel injection system of a diesel engine,
starting becomes impossible. After running out of fuel, or
after disassembling the fuel system, bleed the system
according to the following procedure.
To restart after running out of fuel, turn the key switch to the
“START” position for 15-30 seconds. Try again, if needed.
This unit is equipped with an automatic air bleeding system.
2. Clean the inside of the body and cover using a damp
cloth.
3. Blow dry with compressed air (0.69Mpa {7kgf.cm2,
99.4 PSI} maximum) against the side of the element
along the pleats. Then blow dry against outside along
the pleats, then against inside again.
4. Remove one seal each time the element is cleaned.
Service Daily
5. Replace the outer element after cleaning it 6 times or
after one year. Replace the outer element if indicator is
red even after cleaning it.
If engine is operating in very dusty and dry grass conditions,
a clogged air cleaner will result in high fuel consumption,
loss of power and excessive carbon buildup in the
combustion chamber.
6. Check the inner cylinder element clamping nut for
looseness, and retighten if necessary.
Cleaning the Fuel Strainer
7. If seal washer is damaged or the threads of wing nut are
damaged, replace.
Clean the fuel strainer if it contains dust or water. Remove
dust or water in the strainer cap and wash it in diesel. Securely
fasten the fuel strainer cap so that fuel will not leak. Check
the fuel strainer every 200 hours of operation or once a month.
8. Remove evacuator valve and clean it with compressed
air. Reinstall.
Check Oil Level
Inner element (if equipped)
Check the crankcase oil level prior to each use, or when the
fuel tank is filled. Insufficient oil may cause severe damage
to the engine. Make sure the generator is level.The oil level
must be between the two notches on the dipstick as shown
in Figure 29.
1. Remove the cover and outer element, then remove the
inner element.
2. Cover the air connector opening (outer side) with clean
cloth or cloth tape.
3. Clean the inside of the body. Remove air connector
opening protection.
Check Electric Heater (If equipped)
Before starting in cold weather (once a year), please contact
your Komatsu distributor for inspection. Remove electric
heater from the engine intake manifold and check for
disconnections or dirt. When checking or installing the electric
heater, replace the gasket with a new part.
4. Install a new inner cylinder element to the cylinder and
tighten the nut.
5. Install element.
6. After replacing the element, press the button of the dust
indicator to return the red piston to its original position.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — MAINTENANCE
DCA-300SSK SERIES — MAINTENANCE
14. Drain the water inside reserve tank, clean the inside of
WARNING - BURN HAZARDS
the reserve tank, then fill with coolant/water mixture to
between the full and low lines.
Allow engine to cool when flushing out
radiator. Flushing the radiator while hot
could cause serious burns from water or
steam.
15. Stop the engine, wait for 3 minutes, add tap water until
the water level reaches near the water filer port, then
tighten the radiator cap.
Changing Oil
Flushing Out Radiator and Changing Coolant
1. Make sure the oil is cool before changing.
1. Stop the engine and allow to cool. Tighten valve of the
corrosion resistor (if equipped).
2. Set a container directly under the drain plug of the oil
pan. Loosen the drain plug slowly.
2. Turn water filer cap slowly and remove it.
3. Check the drained oil for excessive metal particles or
foreign material. Contact the distributor if there is metal
particles or foreign material.
3. Prepare a container to catch the coolant, then open drain
plug of the radiator or heat exchanger and drain plug of
the engine, and drain the coolant.
4. Using a filter wrench, turn filter cartridge to the left to
remove it. If the filter cartridge is filled with a large
amount of oil, wait 10 minutes or so before removing.
Make sure there is no old gasket stuck on the filter holder.
4. After draining the coolant, close drain plugs and fill with
tap water.
5. When the water level is near the mouth of the water
filler, open drain plugs and start the engine, and run at
low idling. Keep the engine running at low idling and
flush the radiator for about 10 minutes.
5. Tighten drain plug. Clean the filter holder, fill the new
filter cartridge with clean engine oil, coat the packing
and thread of the new filter cartridge with engine oil,
then install it to the filter holder. Tighten until the gasket
surface contacts the seal surface of the filter holder,
then tighten it a further 3/4 to 1 turn.
6. Adjust the flow of the water flowing in and draining out to
ensure that the radiator is always full during the flushing
operation. While flushing water through the system,
watch carefully the water inlet hose does not come out
of the radiator filler port.
6. Add engine oil through oil filler until the oil level is between
the H and L marks on the dipstick.
7. After flushing, stop the engine, open drain plug and drain
the water, then close drain plugs.
7. Run the engine at idling for a short time, then stop the
engine. Recheck the oil level and fill as necessary.
8. After draining the water, flush the system with a flushing
agent. See instructions on flushing agent label.
Replacing Fuel Filter
1. Set the container under the filter cartridge to catch fuel.
9. After flushing, open drain plugs and drain out all the
water, then close drain plugs and add tap water so the
water level is near the mouth of the water filler.
2. Using a filter wrench, turn the filter cartridge to the left
to remove it.
3. Clean the filter holder, fill the new filter cartridge with
fuel, coat the packing surface of the filter cartridge with
engine oil, then install the cartridge to the filter holder.
10. When the water level is near the mouth of the water
filler, open drain plugs and start the engine, run at low
idling and continue to flush the system until clean water
comes out. Adjust the flow of the water flowing in and
draining out to ensure the radiator is always full during
the flushing operation.
4. When installing, tighten until the packing surface
contacts the seal surface of the filter holder then tighten
a further 2/3 of a turn. If the filter cartridge is tighten too
much, the packing will be damaged and will cause fuel
leakage. Fuel leakage will occur if the filter cartridge is
not tightened enough. Always tighten to the correct
angle.
11. When clean water comes out, stop the engine, drain all
the water, then close drain plugs.
12. Remove the corrosion resistor (if equipped) and open
valve.
13. Supply water until it flows over the water filler.
PAGE 46 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — MAINTENANCE
5. After replacing filter cartridge, loosen air bleed plug.
Generator Storage:
6. Loosen the knob of feed pump, and pump it up and down
until no bubbles come out with the fuel from air bleed
plug.
For storage of the generator for over 30 days, the following
is required:
z
Fill the fuel tank completely. Treat with fuel stabilizer if
necessary.
7. After bleeding the air, tighten air bleed plug, then push in
the knob of feed pump and lock it in position.
z
Completely drain oil from the crankcase and refill if
necessary with fresh oil.
8. Replace Corrosion resistor cartridge (if equipped)
9. Screw in valves at the top of the corrosion resistor.
z
z
Clean the entire generator, internal and external.
10. Using a filter wrench, turn the cartridge to the left to
remove it.
Disconnect the negative terminals of the battery and
cover it, or remove it from the generator and store it
separately.
11. Coat the seal surface of the new cartridge with engine
oil and install it to the filter holder.
z
z
If the ambient temperature is expected to drop below
0oC, add antifreeze to the radiator.
12. Tighten until he packing surface contacts the seal
surface of the filter holder, then tighten a further 2/3 of a
turn.
Cover the generator set and store in a clean, dry place
13. Open valves.
Removal From Long Term Storage:
z
Apply oil to the engine valve and rocker arms, and
examine the operating condition of the valves.
Cleaning Breather Element
1. Loosen the clamp, then remove the hose and take out
breather. Wipe off the dirt around the breather. Check
the O-ring, and replace if necessary.
z
Remove the oil filler pipe from the turbocharger oil inlet
port, add 0.5-1L (0.13-0.26 gal) of oil to the turbocharger,
reinstall the oil filler pipe.
2. Wash the breather in diesel fuel or flushing oil, blow dry
with compressed air, then reinstall it.
z
z
z
z
Change the oil in engine oil pan.
Replace all the filters.
3. Inspect the hose and if there is any deteriorated oil stuck
inside the hose. Replace hose if necessary.
Flush the inside of the cooling system.
Drain the water from the fuel tank and bleed the air from
the fuel system.
Greasing
1. Using a grease pump, grease the fan hub (1 place) and
tension pulley (2 places).
z
If the engine has not been started for more than one
year, contact your Komatsu distributor to have engine
overhauled.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES — MAINTENANCE
If the generator will be used daily, the battery should normally
not require charging. If the generator will be idle (not used)
for long periods of time, apply power to the battery charger
receptacle via commercial power using an power cord of
adequate size.
Jacket Water Heater and Internal Battery Charger 120
VAC Input Receptacles (OPTIONAL)
This generator is equipped with two 120 VAC, 20 amp input
receptacles located on the output terminal panel.
The purpose of these receptacles is to provide power via
commercial power to the jacket water heater and internal
battery charger.
To ensure adequate starting
capability, always have power
applied to the generator's
These receptacles will ONLY function when commercial
power has been supplied to them (Figure 73). To apply
commercial power to these receptacles, a power cord of
adequate size will be required (See Table 6).
NOTE
internal battery charger.
When using the generator in hot climates there is no reason
to apply power to jacket water heater. However, if the
generator will be used in cold climates it is always a good
idea to apply power to the jacket water heater at all times.To
apply power to the jacket water heater simply apply power to
the jacket water heater receptacle via commercial power using
an power cord of adequate size.
Battery Charger/Jacket Water
Heater Power Connections
PAGE 48 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES —TRAILER MAINTENANCE
Trailer Maintenance
8. Tire Size - Indicates the diameter of the tire in inches
(10,12,14, etc.), and the width in millimeters
(175,185,205, etc.). The tire diameter must match the
diameter of the tire rim.
This section is intended to provide the user with generic
trailer service and maintenance information.The service and
maintenance guidelines referenced in this section refer to a
wide range of trailers.
9. Tire Ply - The tire ply (layers) number is rated in letters;
2-ply,4-ply,6-ply, etc.
Remember periodic inspection of the trailer will ensure safe
towing of the generator and will prevent personal injury and
damage to the equipment.
10. Wheel Hub - The wheel hub is connected to the trailer’s
axle.
The definitions below describe some of the major components
of a typical trailer that would be used with the DCA-400SSVU
11. Tire Rim - Tires mounted on a tire rim. The tire rim must
match the size of the tire.
Whisperwatt
™
Generator.
12. Lug Nuts - Used to secure the wheel to the wheel hub.
Always use a torque wrench to tighten down the lug
nuts. See Table 18 and Figure 64 for lug nut tightening
and sequence.
1. Fuel Cell - Provides an adequate amount of fuel for the
equipment in use. Fuel cells must be empty when trans-
porting equipment.
2. Braking System - System employed in stopping the
trailer. Typical braking systems are electric, surge, hy-
draulic, hydraulic-surge and air.
13. Axle - Indicates the maximum weight the axle can sup-
port in pounds, and the diameter of the axle expressed
in inches. Please note that some trailers have a double
axle. This will be shown as 2-6000 lbs., meaning two
axles with a total weight capacity of 6000 pounds.
3. GVWR- Gross Vehicle Weight Rating (GVWR) is the
maximum number of pounds the trailer can carry, in-
cluding the fuel cell (empty).
14. Suspension - Protects the trailer chassis from shocks
transmitted through the wheels. Types of suspension
used are leaf, Q-flex, and air ride.
4. Frame Length - Measurement is from the ball hitch to
the rear bumper (reflector).
5. Frame Width - Measurement is from fender to fender
15. Electrical - Electrical connectors (looms) are provided
with the trailer so the brake lights and turn signals can
be connected to the towing vehicle.
6. Jack Stand - Trailer support device with maximum pound
requirement from the tongue of the trailer.
16. Application - Indicates which units can be employed
7. Coupler - Type of hitch used on the trailer for towing.
on a particular trailer.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES —TRAILER MAINTENANCE
Brakes
Hydraulic Surge Brakes
Trailer brakes should be inspected the first 200 miles of Hydraulic surge brakes should not require any special
operation. This will allow the brake shoes and drums to seat attention with the exception of routine maintenance such as
properly. After the first 200 mile interval, inspect the brakes shoe and lining replacement. Brake lines should be
every 3,000 miles. If driving over rough terrain, inspect the periodically checked for cracks, kinks, or blockage.
brakes more frequently.
Figure 74 displays the major hydraulic surge brake
components that will require inspection and maintenance.
Use Table 14 as a basic trouble shooting guide when brake
problems occur. Please inspect these components as
required using steps 1 through 6 as listed below:
Brake Adjustment
1. Place the trailer on jack stands. Make sure the jack
stands are placed on secure level ground.
2. Check the wheel and drum for free rotation.
3. Remove the adjusting hole cover from the adjusting slot
at the bottom brake backing plate.
4. With a screwdriver or standard adjusting tool, rotate the
star wheel of the adjuster assembly to expand the brake
shoes.
5. Adjust the brake shoes outward until the pressure of the
lining against the wheel drum makes the wheel difficult
to turn.
6. Adjust, rotate the star wheel in the opposite direction
until the wheel rotates freely with slight lining drag.
7. Replace the adjusting hole cover and lower the trailer to
the ground.
Figure 74. Hydraulic Brake Components
Actuator
Hydraulic surge braking requires the installation of an actuator
at the tongue of the trailer. Remember the surge or push of
the trailer toward the tow vehicle automatically synchronizes
the trailer brakes with the tow vehicle brakes. As the trailer
pushes against the tow vehicle the actuator telescopes
together and applies force to the master cylinder, supplying
hydraulic pressure to the trailer brakes.
Periodically check and test the surge “actuator ” to make
sure that it is functioning correctly. Never use an undersize
actuator.
8. Repeat steps 1 through 7 on the remaining brakes.
Table 14. Hydraulic Brake Troubleshooting
Symptom
Possible Cause
Solution
Repair or replace.
Reburnish or replace.
Correct weight.
No Brakes
Brake line broken or kinked?
Brake lining glazed?
Trailer overloaded?
Weak Brakes or Brakes Pull to
One Side
Brake drums scored or grooved?
Tire pressure correct?
Machine or replace.
Inflate all tires equally.
Match tires.
Tires unmatched on the same axle?
Brake components loose, bent or broken?
Brake drums out-of-round?
System lubricated?
Replace components.
Replace.
Locking Brakes
Noisy Brakes
Lubricate.
Brake components correct?
Replace and correct.
Brake lining thickness incorrect or not
adjusted correctly?
Install new shoes and
linings.
Dragging Brakes
Enough brake fluid or correct fluid?
Replace rubber parts
fill with dot 4 fluid.
PAGE 50 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES —TRAILER MAINTENANCE
Suspension
Tires/Wheels/Lug Nuts
The leaf suspension springs and associated components
(Figure 75) should be visually inspected every 6,000 miles
for signs of excessive wear, elongation of bolt holes, and
loosening of fasteners. Replace all damaged parts
(suspension) immediately. Torqued suspension components
as detailed in Table 16.
Tires and wheels are a very important and critical
components of the trailer. When specifying or replacing the
trailer wheels it is important the wheels, tires, and axle are
properly matched.
CAUTION - EYESIGHT HAZARD
ALWAYS wear safety glasses when
removing or installing force fitted parts.
Failure to comply may result in serious
injury.
CAUTION - REPAIRINGTRAILERWHEELS
DO NOT attempt to repair or modify a wheel. DO NOT
install in inner tube to correct a leak through the rim. If the
rim is cracked, the air pressure in the inner
tube may cause pieces of the rim to
explode (break off) with great force and
cause serious eye or bodily injury.
Figure 75. Major Suspension Components
Tire Wear/Inflation
Tire inflation pressure is the most important factor in tire life.
Pressure should be checked cold before operation DO NOT
bleed air from tires when they are hot!. Check inflation
pressure weekly during use to insure the maximum tire life
and tread wear.
Table 16. Suspension Torque Requirements
Item
Torque (Ft.-Lbs.)
MIN-30 MAX-35
MIN-45 MAX-60
MIN-45 MAX-60
3/8" U-BOLT
7/16" U-BOLT
1/2" U-BOLT
Table 15 (Tire Wear Troubleshooting) will help pinpoint the
causes and solutions of tire wear problems.
SHACKLE BOLT
SNUG FIT ONLY. PARTS MUST ROTATE FREELY.
LOCKING NUTS OR COTTER PINS ARE PROVIDED
TO RETAIN NUT-BOLT ASSEMBLY.
SPRING EYE BOLT
SHOULDER TYPE
SHACKLE BOLT
MIN-30 MAX-50
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK SERIES —TRAILER MAINTENANCE
Lug NutTorque Requirements
It is extremely important to apply and maintain proper wheel
mounting torque on the trailer. Be sure to use only the
fasteners matched to the cone angle of the wheel. Proper
procedure for attachment of the wheels is as follows:
1. Start all wheel lug nuts by hand.
2. Torque all lug nuts in sequence. See Figure 77. DO NOT
torque the wheel lug nuts all the way down. Tighten
each lug nut in 3 separate passes as defined by Table 17.
3. After first road use, retorque all lug nuts in sequence.
Check all wheel lug nuts periodically.
Table 17. Tire Torque Requirements
Wheel Size
First Pass
FT-LBS
Second Pass
FT-LBS
Third Pass
FT-LBS
12"
13"
14"
15"
16"
20-25
20-25
20-25
20-25
20-25
35-40
35-40
50-60
50-60
50-60
50-65
50-65
90-120
90-120
90-120
Figure 76. Wheel Lug Nuts Tightening Sequence
NEVER use an pneumatic air
gun to tighten wheel lug nuts.
Use a torque wrench to tighten
lug nuts.
NOTE
PAGE 52 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK —TRAILER-WIRING DIAGRAM
Figure 77. Trailer/Towing Vehicle Wiring Diagram
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — GENERATORWIRING DIAGRAM
Figure 78. Generator Wiring Diagram
PAGE 54 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK— ENGINEWIRING DIAGRAM (S/N 3696506 AND BELOW)
Figure 79. Engine Wiring Diagram (S/N 3696506 and Below)
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — ENGINEWIRING DIAGRAM (S/N3696507TO 3701673)
Figure 80. Engine Wiring Diagram (S/N 3696507-3701673)
PAGE 56 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — ENGINE WIRING DIAGRAM (S/N 3701674 AND ABOVE)
Figure 81. Engine Wiring Diagram (S/N 3701674 and Above)
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK —TROUBLESHOOTING (ENGINE)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, use Table 18 (Engine Troubleshooting) as a basic guideline for troubleshooting the engine. If the problem
cannot be remedied, consult our company's business office or service plant.
TABLE 18. ENGINE TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
No fuel?
SOLUTION
Replenish fuel.
Bleed system.
Air in the fuel system?
Water in the fuel system?
Fuel pipe clogged?
Remove water from fuel tank.
Clean fuel pipe.
Fuel filter clogged?
Clean or change fuel filter.
Excessively high viscosity of
fuel or engine oil at low
temperature?
Use the specified fuel or engine oil.
Fuel with low cetane number?
Use the specified fuel.
Tighten nut.
Fuel leak due to loose injection
pipe retaining nut?
Engine does not start.
Incorrect injection timing?
Fuel cam shaft worn?
Adjust.
Replace.
Injection nozzle clogged?
Injection pump malfunctioning?
Clean injection nozzle.
Repair or replace.
Seizure of crankshaft, camshaft,
piston, cylinder liner or bearing?
Repair or replace.
Compression leak from
cylinder?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Improper valve timing?
Piston ring and liner worn?
Excessive valve clearance?
Battery discharged?
Correct or replace timing gear.
Replace.
Adjust.
Charge battery.
Repair or replace.
Repair or replace.
Connect wiring.
Starter malfunctioning?
Key switch malfunctioning?
Wiring disconnected?
Starter does not run.
PAGE 58 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK —TROUBLESHOOTING (ENGINE)
TABLE 18. ENGINE TROUBLESHOOTING (CONTINUED)
SYMPTOM
POSSIBLE PROBLEM
Fuel filter clogged or dirty?
Air cleaner clogged?
SOLUTION
Clean or change.
Clean or change.
Fuel leak due to loose injection
pipe retaining nut?
Tighten nut.
Repair or replace.
Adjust.
Injection pump malfunctioning?
Engine revolution is not
smooth.
Incorrect nozzle opening
pressure?
Injection nozzle stuck or
clogged?
Repair or replace.
Fuel over flow pipe clogged?
Governor malfunctioning?
Excessive engine oil?
Clean.
Repair.
Reduce to the specified level.
Repair or replace.
Piston ring and liner worn or
stuck?
Either white or blue exhaust gas
is observed.
Incorrect injection timing?
Deficient compression?
Overload?
Adjust.
Adjust top clearance.
Lessen the load.
Use the specified fuel.
Clean or change.
Clean or change.
Repair or replace the nozzle.
Adjust.
Low grade fuel used?
Fuel filter clogged?
Either black or dark gray
exhaust gas is observed.
Air cleaner clogged?
Deficient nozzle injection?
Incorrect injection timing?
Engine's moving parts seem to
be seizing?
Repair or replace.
Uneven fuel injection?
Repair or replace the injection pump.
Repair or replace the nozzle.
Deficient output.
Deficient nozzle injection?
Replace head gasket, tighten cylinder head bolt, glow plug and
nozzle holder.
Compression leak?
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK —TROUBLESHOOTING (GENERATOR)
Practically all breakdowns can be prevented by proper handling and maintenance inspections, but in the event of a
breakdown, use Table 19 (Generator Troubleshooting) as a basic guideline for troubleshooting the generator. If the problem
cannot be remedied, consult our company's business office or service plant.
TABLE 19. GENERATOR TROUBLESHOOTING
SYMPTOM
POSSIBLE PROBLEM
AC Voltmeter defective?
SOLUTION
Check output voltage using a voltmeter.
Check wiring and repair.
Is wiring connection loose?
Is AVR defective?
No Voltage Output
Replace if necessary.
Defective Rotating Rectifier?
Is engine speed correct?
Is wiring connections loose?
Defective AVR?
Check and replace.
Turn engine throttle lever to "High".
Check wiring and repair.
Low Voltage Output
High Voltage Output
Replace if necessary.
Is wiring connections loose?
Defective AVR?
Check wiring and repair.
Replace if necessary.
Short Circuit in load?
Over current?
Check load and repair.
Confirm load requirements and reduce.
Check and replace.
Circuit Breaker Tripped
Defective circuit breaker?
Over current Relay actuated?
Confirm load requirement and replace.
PAGE 60 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK —TROUBLESHOOTING (ENGNE CONTROLLER)
TABLE 20. ENGINE CONTROLLER TROUBLESHOOTING (MPEC)
Sympton
Possible Cause
Solution
Low oil level?
Fill oil level.
Oil pressure sending unit failure?
Time delay malfuntion in Controller?
Wire shorted?
Replace oil pressure sending unit.
Refer to dealer.
Low oil pressure light
is on.
Inspect/repair wire.
Low coolant level?
Fill coolant level.
Low coolant level light
is on.
Sending unit failure?
Replace sending unit.
Replace/charge battery.
Tighten/replace fan belt.
Clean/repair radiator grill.
Close doors.
Low battery voltage?
Fan belt tension incorrect?
Air flow is not circulation through radiator?
Doors open?
Exhaust leaking?
Replace/repair gaskets or faulty part.
Check/reduce load.
High coolant
temperture light is on.
Generator being overloaded?
Thermostat failure?
Replace thermostat.
Clear all air intakes.
Replace temperature switch.
Fill fuel level.
Air intake blocked?
Temperature switch failure?
No or low Fuel?
Overcrank light is on.
Overspeed light is on.
Controller needs to be calibrated?
RPM engine speed too high?
Governor actuator needs to be adjusted?
Governor controller needs to be adjusted?
Engine Controller needs to be calibrated?
Magnetic pick up out of adjustment?
Magnetic pick up dirty?
Refer to dealer.
Adjust RPM.
Adjust governor actuator.
Adjust governor controller.
Refer to dealer.
Adjust magnetic pick up.
Clean magnetic pick up.
Loss of MPU light(s) or
on.
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks
QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
REMARKS Column
Sample Parts List:
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
NO. PART NO. PART NAME
QTY. REMARKS
1
2
2
3
4
12345
BOLT ....................... 1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. .... 1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................ 1.... S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
TBD (To Be Determined) is generally used to show a part
that has not been assigned a formal part number at time of
publication.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 62 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK — SUGGESTED SPARE PARTS
DCA-300SSKW/KOMATSU SA6D125E-2/ SAA6D125E-2
1 to 5 Units
Qty.
P/N
Description
10 .............. 6125817032 .....................AIR FILTER, INNER & OUTER
10 .............. 6003118321 .....................FUEL FILTER
10 .............. 6002111231 .....................OIL FILTER
5 ................ 6004111151 .....................CARTRIDGE, CORROSION RESISTOR
3 ................ 0810105400 .....................FUEL FILTER, FUEL TANK
2 ................ xxxxxxxxxx .....................ENGINE FAN BELT
1 ................ 6008155390 .....................SWITCH, STARTER................................. UP TO S/N 370163
5 ................ 615 ...................................KEY SET, STARTER SWITCH (2) ........... UP TO S/N 370163
1 ................ 6152611520 .....................RADIATOR HOSE (UPPER)..................... UP TO S/N 3708296
1 ................ 6152611531 .....................RADIATOR HOSE (LOWER) .................... UP TO S/N 3708296
1 ................ 6152611530 .....................RADIATOR HOSE (UPPER)..................... S/N 3708297 AND ABOVE
1 ................ 6152621540 .....................RADIATOR HOSE (LOWER) .................... S/N 3708297AND ABOVE
1 ................ 0605505030 .....................FUEL CAP
1 ................ 0601850590 .....................KEY, FUEL CAP
1 ................ 0601820625 .....................AUTOMATICVOLTAGE REGULATOR
1 ................ 0601810072 .....................PILOT LAMP
2 ................ 0601810261 .....................BULB, PILOT LAMP
1 ................ 23S0311150M ..................CAP, RADIATOR ...................................... UP TO S/N 3708296
1 ................ 0602122200 .....................UNIT, OIL PRESSURE
1 ................ 0602123206 .....................UNIT, WATERTEMPERATURE
1 ................ 0602121052 .....................CHARGING AMMETER
1 ................ 0601804887 .....................CIRCUIT BREAKER, OUTPUT
............................................................TERMINAL,KM51, 265V 20A................... UP TO S/N 3706720
1 ................ 0601808803 .....................CIRCUIT BREAKER, OUTPUT
............................................................TERMINAL,QOU120B 20A ...................... TO S/N 3706721 ABOVE
1 ................ 0601805840 .....................CIRCUIT BREAKER, OUTPUT
............................................................TERMINAL,KM52, 265V 50A................... UP TO S/N 3706720
1 ................ 0601808804 .....................CIRCUIT BREAKER, OUTPUT
............................................................TERMINAL,QOU250B 50A ...................... TO S/N 3706721 ABOVE
Part number on this Suggested Spare Parts
list may supercede/replace the P/N shown
in the text pages of this book.
NOTE
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK GENERATOR ASSY.
GENERATOR ASSY.
PAGE 64 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK GENERATOR ASSY.
GENERATOR ASSY.
NO.
1
PART NO.
C2110100302
PART NAME
QTY.
REMARKS
ROTOR ASSY. ............................................... 1 ......... INCLUDES ITEM W/
*
2
3
FIELD ASSY.
1
*
0601842401
0601823282
0018205020
0040005000
0041205000
8201070002
8201611004
C3164200004
8201015003
0012116045
0042616000
0601000209
C3112500004
0071906315
8201614003
0012116040
0042516000
0012112040
0042512000
C2130100103
0226200430
8201323004
0223300140
8201323103
0221200350
0010110035
0041210000
C2132200003
0226000275
0225000500
0017106016
0601850144
C3154000002
C3138000003
0012110080
0042610000
0041210000
0017112045
C3154300104
C3154300004
0010106060
0040006000
0041206000
RESISTOR ...................................................... 2 ......... 80W 300K OHM
RECTIFIER ..................................................... 1 ......... RM50TC-24
HEX. SOCKET HEAD CAP SCREW
LOCK WASHER
PLAIN WASHER
FAN
*
4
5
*
2
2
2
1
12
1
*
5
5
*
*
6
7
*
COUPLING DISK
WASHER, COUPLING HUD
*
8
9
*
BALANCING PLATE ....................................... 1 ......... PURCHASE AS SET OF 1-14
*
10
HEX. HEAD BOLT
LOCK WASHER
BALANCING WEIGHT KIT
BEARING FLANGE
BEARING ........................................................ 1 ......... 6315DDUC3
10
10
1
*
11
*
12
*
13
*
1
14
*
15
COUPLING RING
HEX. HEAD BOLT
LOCK WASHER
HEX. HEAD BOLT
LOCK WASHER
STATOR ASSY.
RUBBER SEAL
CLAMPER
RUBBER SEAL
CLAMPER
RUBBER SEAL
HEX. HEAD BOX
PLAIN WASHER
COVER
1
6
6
12
12
1
1
1
1
1
1
2
2
1
2
1
6
1
1
1
4
4
4
8
1
1
4
4
4
16
17
18
18
19
20
21
22
23
24
25
25
26
27
28
29
30
31
32
33
33
33
34
35
36
37
37
37
RUBBER SEAL
RUBBER SEAL
HEX. HEAD BOLT
GROMMET
END BRACKET
FIELD ASSY. EXCITER
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
HEX. HEAD BOLT
COVER, BEARING
GASKET, BEARING
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK GENERATOR ASSY.
GENERATOR ASSY.
PAGE 66 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK GENERATOR ASSY.
GENERATOR ASSY.(CONT)
NO.
38
39
40
40
41
41
42
42
42
43
44
44
PART NO.
PART NAME
QTY.
1
8
16
16
REMARKS
C3154400003
0017106016
0012112035
0042512000
C3132300003
C3132300014
0010106030
0041206000
0600815000
0605000012
0030020000
0040020000
SUCTION COVER
HEX. HEAD BOLT
HEX. HEAD BOLT
LOCK WASHER
COVER, FAN................................................... 1 ......... S/N3691259TO 3692208
COVER, FAN................................................... 1 ......... S/N3692209 AND ABOVE
HEX. HEAD BOLT
PLAIN WASHER
NUT ................................................................. 1 ......... S/N3692209 AND ABOVE
RUBBER SUSPENSION
HEX. NUT
1
1
2
4
4
LOCK WASHER
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK CONTROL BOX ASSY.
CON
PAGE 68 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK CONTROL BOX ASSY.
CONTROL BOX ASSY.
NO.
1
1
PART NO.
PART NAME
QTY.
REMARKS
C2214000102 CONTROL BOX .............................................. 1 ............... S/N 3691259TO 3706720
C2214001502 CONTROL BOX .............................................. 1 ............... S/N 3706721 AND ABOVE
2
3
4
4
0601806134
0027106016
0601807373
0601807513
0601802525
CURRENTTRANSFORMER .......................... 3 ............... CT-5MR500/5A
MACHINE SCREW
CIRCUIT BREAKER,XS800NS800A .............. 1 ............... UPTO 3706720
CIRCUIT BREAKER, S6G800A...................... 1 ............... S/N 3706721AND ABOVE
HANDLE, CIRCUIT BREAKER....................... 1 ............... S/N 3691259TO 3706720
6
5
6
6
C2214600004 BRACKET, CIRCUIT BREAKER .................... 2 ............... S/N 3691259TO 3706720
C2261600204 BRACKET, CIRCUIT BREAKER .................... 1 ............... S/N 3706721AND ABOVE
7
8
8
8
8
9
0017108020
0021008045
0030008000
0040008000
0041208000
0601820625
0027105016
0601820892
0027104016
HEX. HEAD BOLT
MACHINE SCREW
4
4
HEX. NUT ....................................................... 4 ............... S/N 3691259TO 3706720
LOCK WASHER .............................................. 4 ............... S/N 3691259TO 3706720
PLAIN WASHER ............................................. 4 ............... S/N 3691259TO 3706720
AUTOMATICVOLTAGE REGULATOR ............. 1 ............... NTA-5A-2T
MACHINE SCREW
OVER CURRENT RELAY ............................... 1 ............... TH-N20HZKP
10
11
12
13
14
15
16
17
18
19
20
21
22
23
23
23
23
24
25
4
MACHINE SCREW
2
1
10
20
3
C2274000103 CHANGE-OVER BOARDVOLTAGE
8201852104
0017108030
CHANGETERMINAL
HEX. HEAD BOLT
C2277200004 TERMINAL PLATE
8201853104
8201852504
0801830704
0040012000
0041412000
0017110030
CHANGE PLATE
HEX. HEAD BOLT
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
HEX. HEAD BOLT
6
13
13
26
26
4
C2261500003 SET PANEL, ELECTRIC PARTS .................... 1 ............... S/N 1337508TO 3691258
C2261500013 SET PANEL, ELECTRIC PARTS .................... 1 ............... S/N 3691259TO 3696506
C2261500703 SET PANEL, ELECTRIC PARTS .................... 1 ............... S/N 3696507TO 3701673
C2261500713 SET PANEL, ELECTRIC PARTS .................... 1 ............... S/N 3701674 AND ABOVE
0017108020
6008151252
HEX. HEAD BOLT .......................................... 4
EMERGENCY RELAY .................................... 1 .............. S/N 3696507TO 3701673
......................................................................................... REPLACES 0602200446
HEX. HEAD BOLT .......................................... 4 .............. S/N 3696507TO 3701673
RELAY ............................................................ 2 .............. HH62SDC24V
MACHINE SCREW ......................................... 4
26
27
28
0017106016
0601824542
0027103010
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 69
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK CONTROL BOX ASSY.
CONTROL BOX ASSY. (CONT)
PAGE 70 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK CONTROL BOX ASSY.
CONTROL BOX ASSY. (CONT)
NO.
29
30
31
32
32
33
34
35
36
37
38
39
39
40
41
42
42
43
44
45
46
47
47
47
47
48
49
50
51
52
53
54
55
56
57
58
59
60
PART NO.
0602201911
0027106016
PART NAME
QTY. REMARKS
UNIT, BATTERY SENSOR ..........................1 ........ C7038A-00-00
MACHINE SCREW
1
1
C2224000503 CONTROL PANEL
C2224000404 CONTROL PANEL ......................................1 ........ S/N3691259TO 3706720
C2224001504 CONTROL PANEL ......................................1 ........ S/N3706721 AND ABOVE
0605011211
0601807622
0601806979
0601801040
0601806887
0601801041
0601810072
0601810261
0601840073
0601840121
0601810161
0601810214
0207004000
0601830710
PIN
2
FREQUENCY METER ................................1 ........ RSC-80F 220V 45-65HZ
AC AMMETER ...........................................1 ........ RSS-80 0-500A 0-1000A
CHANGE-OVER SWITCH, AMMETER ......1 ........ SL-2AS
AC VOLTMETER ........................................1 ........ RSR-80 0-600V
CHANGE-OVER SWITCH,VOLTMETER ...1 ........ SL-2VS
PILOT LAMP ..............................................1 ........ LP-132DC 220V
BULB ..........................................................1 ........ CT-13W
RHEOSTAT (VOLTAGE REGULATOR) ........1 ........ RA20A2SE102BJ 2W 1K OHM
KNOB
1
PANEL LIGHT .............................................1 ........ V325070
BULB
HEX. NUT
SWITCH, PANEL LIGHT
1
2
1
C2214600104 COVER .......................................................1 ........ S/N3691259TO 3706720
0027105016 MACHINE SCREW .....................................4 ........ S/N3691259TO 3706720
C9221100004 HEX. HEAD BOLT
0040008000
0041208000
505015300
0017108040
3871824004
0041206000
0605010502
C2214500004 COVER, CONTROL BOX
0017108020 HEX. HEAD BOLT
C2214300004 SIDE PANEL, CONTROL BOX
0017108020 HEX. HEAD BOLT
C2214400004 PANEL, CONTROL BOX
0017108020
0017110025
0601823861
0027104015
2
2
2
LOCK WASHER
PLAIN WASHER
SNAP RING ................................................2 ........ REPLACES 0080200007
HEX. HEAD BOLT
STOPPER, CONTROL PANEL
PLAIN WASHER
4
1
1
1
1
8
1
4
1
8
4
SNAP PIN
HEX. HEAD BOLT
HEX. HEAD BOLT
ENGINE STOP UNIT, MSA9014 .................1 ........ S/N3696507TO 3701673
MACHINE SCREW .....................................2 ........ S/N3696507TO 3701673
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 71
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK CONTROL BOX ASSY.
CONTROL BOX ASSY. (CONT)
PAGE 72 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK CONTROL BOX ASSY.
CONTROL BOX ASSY. (CONT)
NO.
61
62
62
62
63
63
63
63
64
65
65
65
65
66
67
68
69
70
71
72
72
73
73
74
75
76
77
78
PART NO.
PART NAME
QTY.
REMARKS
0601823240
0021004030
0040004000
0041204000
0601802149
0601802149
0601806671
0601802218
0027103020
0601823732
0601827655
0601823109
0601824400
0027104020
0601823706
0027104015
0601815402
0027104020
RECTIFIER, DE4503 ..................... 4 .............. S/N 3696507TO 3701673
MACHINE SCREW ........................ 2 .............. S/N 3696507TO 3701673
LOCK WASHER ............................. 2 .............. S/N 3696507TO 3701673
PLAIN WASHER ............................ 2 .............. S/N 3696507TO 3701673
FUSE, 10A..................................... 1 .............. S/N 3696507TO 3701673
FUSE (RIGHT), 10A ...................... 1 .............. S/N 3701674 AND ABOVE
FUSE (LEFT), 15A......................... 1 .............. S/N 3701674 AND ABOVE
HOLDER, FUSE ............................ 1 .............. S/N 3701674 AND ABOVE
MACHINE SCREW ........................ 2 .............. S/N 3701674 AND ABOVE
RELAY ........................................... 1 .............. S/N 3696507TO 3699681
RELAY ........................................... 1 .............. S/N 3699682 AND ABOVE
SOCKET ........................................ 1 .............. S/N 3696507 AND ABOVE
HOLDER ........................................ 1 .............. S/N 3696507 AND ABOVE
MACHINE SCREW ........................ 2 .............. S/N 3696507 AND ABOVE
RELAY, HE1ADC24V ..................... 1 .............. S/N 3696507 AND ABOVE
MACHINE SCREW ........................ 2 .............. S/N 3696507 AND ABOVE
TERMINAL BOARD, TS144P......... 1 .............. S/N 3696507 AND ABOVE
MACHINE SCREW ........................ 2 .............. S/N 3696507 AND ABOVE
ECU9988N300/400 CONTROLLER ............................... 1 .............. REPLACES 0601827396 & 0602202545
0601831340
0601830765
DYNT11200
0602202470
SWITCH, 82608DPDT ................... 1 .............. S/N 3696507TO 3700240
SWITCH, S303T ............................ 1 .............. S/N 3700241 AND ABOVE
SPEED SENSOR .......................... 1 .............. S/N 3696507 AND ABOVE
SEALED CABLE............................ 1 .............. S/N 3696507 AND ABOVE
DYN110654000024 CONTROLLER ............................... 1 .............. S/N 3701674~; REPLACES 0602202598
0027104020
0601840009
C3262600004
0017106015
MACHINE SCREW ........................ 4 .............. S/N 3701674 ABOVE
RHEOSTAT, RA20A2SE5028 ......... 1 .............. S/N 3701674 ABOVE
BRACKET ...................................... 1 .............. S/N 3701674 ABOVE
HEX. HEAD BOLT ......................... 2 .............. S/N 3701674 ABOVE
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 73
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3697258 AND BELOW)
ENGINE & RADIATOR ASSY. (S/N 3697258 AND BELOW)
PAGE 74 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3697258 AND BELOW)
ENGINE & RADIATOR ASSY. (S/N 3697258 AND BELOW)
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
6155009100
ENGINE, KOMATSU SA6D 125E-2 .............. 1 ..........S/N 3691258 AND BELOW
....................................................................................REPLACES C2924200014
ELEMENT, AIR CLEANER............................ 1 ..........REPLACES 0602040156
CARTRIDGE, OIL FILTER ............................ 1 ..........REPLACES 0602041146
CARTRIDGE, FUEL FILTER ......................... 1 ..........REPLACES 0602042146
CARTRIDGE, CORROSION RESISTOR ...... 1 ..........REPLACES 0602045143
DUST SENSOR ............................................ 1 ..........REX01-8126
2
3
4
5
6
7
8
9
6125817032
6002111231
6003118293
6004111151
0602040678
8185112004
0010118060
0030018000
0040018000
0041218000
0605000011
0030016000
0040016000
6152619720
6152619170
0010012055
0030012000
0040012000
0041212000
8195123104
0017112025
0017110025
6152611520
6152611531
0726120911
0728100809
0728100909
0728001920
ENGINE FOOT.............................................. 1 ..........S/N 3691258 AND BELOW
HEX. HEAD BOLT......................................... 2 ..........S/N 3691258 AND BELOW
HEX. NUT ..................................................... 2 ..........S/N 3691258 AND BELOW
LOCKWASHER ............................................ 2 ..........S/N 3691258 AND BELOW
PLAIN WASHER ........................................... 4 ..........S/N 3691258 AND BELOW
RUBBER SUSPENSION
HEX. NUT
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
2
4
4
LOCKWASHER
RADIATOR .................................................... 1 ..........REPLACES 0602011946
RUBBER SHEET .......................................... 2 ..........REPLACES 0605000490
HEX. HEAD BOLT
HEX. NUT
4
4
4
8
2
2
2
LOCKWASHER
PLAIN WASHER
BRACKET, RADIATOR
HEX. HEAD BOLT
HEX. HEAD BOLT
RADIATOR HOSE ......................................... 1 ..........REPLACES 0602014513
RADIATOR HOSE ......................................... 1 ..........REPLACES 0602014641
RADIATOR HOSE ......................................... 1 ..........REPLACES 0602014541
HOSE BAND ................................................. 6 ..........REPLACES 0602014067
HOSE BAND ................................................. 2 ..........REPLACES 0602014056
HOSE BAND ................................................. 2 ..........REPLACES 0602014058
0802081003C RESERVE TANK ........................................... 1 ..........REPLACES 0802081003
0802010900
C231710003
0017108020
0199601800
0193601300
0193600500
0194100800
0605515170
CAP, RESERVE TANK .................................. 1 ..........REPLACES 0602010900
BRACKET, RESERVE TANK
HEX. HEAD BOLT
HOSE
HOSE
HOSE
HOSE
HOSE BAND
1
2
1
1
1
1
5
1
2
C2327100003 BREATHER PIPE
0017108020 HEX. HEAD BOLT
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 75
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (UPTO S/N3697258)
ENGINE & RADIATOR ASSY. (UP TO S/N3697258)
PAGE 76 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (UPTO S/N3697258)
ENGINE & RADIATOR ASSY. (UP TO S/N3697258)
NO.
41
42
43
44
45
46
47
48
49
50
51
PART NO.
PART NAME
U BOLT
HEX. NUT
QTY.
REMARKS
0603320112
0038408000
0268200700
0605515132
C2358300103
0017110020
C2358300003
0017108020
0010016030
0040016000
0041216000
1
2
1
2
1
2
1
1
1
1
1
HOSE
HOSE BAND
CLAMPER ROD
HEX. HEAD BOLT
CLAMPER ROD
HEX. HEAD BOLT
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 77
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3708270TO 3708296)
ENGINE & RADIATOR ASSY. (S/N3691259 TO S/N 3708296)
PAGE 78 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3708270TO 3708296)
ENGINE & RADIATOR ASSY. (S/N3691259 TO S/N 3708296)
NO.
1
1
2
3
4
5
6
7
PART NO.
PART NAME
QTY.
REMARKS
C2924200154
C2925200014
6125817032
6002111231
6003118321
6004111151
0602040678
0605000011
0030016000
0040016000
6152619720
615261970
ENGINE ................................................................. 1 .......... REPLACES S/N 3691259 TO 3701673
ENGINE ................................................................. 1 .......... S/N3701674 TO 3708269
ELEMENT, AIR CLEANER, INNER/OUTER
CARTRIDGE, OIL FILTER
CARTRIDGE, FUEL FILTER
CARTRIDGE, CORROSION RESISTOR
DUST SENSOR ..................................................... 1 .......... REX018126
RUBBER SUSPENSION ....................................... 2 .......... EA1012
HEX. NUT
1
1
1
1
8
9
4
4
LOCK WASHER
10
11
12
13
14
15
16
17
18
19
20
21
22
24
25
26
27
28
29
30
31
32
33
34
34
35
36
37
38
39
40
41
42
43
44
45
46
RADIATOR............................................................. 1 .......... REPLACES 0602011946
RUBBER SHEET ................................................... 2 .......... REPLACES 0605000490
0010112055
0030012000
0040012000
0041212000
8195123104
0017112025
0017110025
0602014549
6152611531
0726120911
0728100809
0728100197
0802081003
0602010900
C2317100003
0017108020
0199901800
0193601300
0193600500
0194100800
0605515170
C2327100003
C2327100012
0017108020
0603320112
0207008000
0268200700
0605515132
C2358300103
0017110020
C2358300003
0017108020
0010016030
0040016000
0041216000
HEX. HEAD BOLT
HEX. NUT
LOCK WASHER
PLAIN WASHER
BRACKET, RADIATOR
HEX. HEAD BOLT
HEX. HEAD BOLT
RADIATOR HOSE ................................................. 1 .......... REPLACES 6152611520
RADIATOR HOSE ................................................. 1 .......... REPLACES 0602014641
RADIATOR HOSE ................................................. 1 .......... REPLACES 0602014541
HOSE BAND .......................................................... 6 .......... REPLACES 0602014056
HOSE BAND .......................................................... 2 .......... REPLACES 0602014058
RESERVE TANK
CAP, RESERVE TANK
BRACKET, RESERVE TANK
HEX. HEAD BOLT
HOSE
4
4
4
8
2
2
2
1
1
1
2
1
1
1
1
5
HOSE
HOSE
HOSE
HOSE BAND
BREATHER PIPE................................................... 1 .......... S/N3691259 TO 3705209
BREATHER PIPE................................................... 1 .......... S/N3705210 TO 3708269
HEX. HEAD BOLT
U BOLT
HEX. NUT
HOSE
2
1
2
1
2
1
2
1
1
1
1
1
HOSE BAND
CLAMPER ROD
HEX. HEAD BOLT
CLAMPER ROD
HEX. HEAD BOLT
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 79
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
PAGE 80 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
NO.
1
PART NO.
PART NAME
QTY.
REMARKS
C2924200194
6125817032
6002111231
6003118321
6004111151
0602040678
0605000011
0030016000
0040016000
6152629101
6995619230
0010120070
0030020000
004002000
ENGINE ............................................................. 1 ..........KOMATSU SAA6D125E-2
ELEMENT, AIR CLEANER ................................. 1 ..........REPLACES 06020 40145
CARTRIDGE, OIL FILTER ................................. 1 ..........REPLACES 06020 41146
CARTRIDGE, FUEL FILTER.............................. 1 ..........REPLACES 06020 42146
CARTRIDGE, COROSION RESISTOR ............. 1 ..........REPLACES 06020 45143
1-1
1-2
1-3
1-4
1-5
2
SENSOR, DUST REX01-8126
SUSPENSION, RUBBER EA1012
NUT, HEX
1
2
4
4
3
4
WASHER, SPRING
5
RADIATOR ........................................................ 1 ..........REPLACES 06020 12706
SHEET, RUBBER............................................... 2 ..........REPLACES 06050 00085
6
7
BOLT, HEX HEAD
NUT, HEX
4
8
4
8
2
2
2
2
2
8
9
WASHER, SPRING
WASHER, PLAIN
BRACKET, RADIATOR
BOLT, HEX HEAD
WASHER, SPRING
WASHER, PLAIN
BOLT, HEX HEAD
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
29
0041220000
C2311100504
0010112025
0040012000
0041212000
0017110025
6152611530
6125621540
0726120911
0728100809
0728100909
0728100197
6152124380
6152124410
6152124420
0602014900
6152124490
0802081003
0602010900
C2317100304
02292 00550
HOSE, RADIATOR ............................................. 1 ..........REPLACES 06020 14539
HOSE, RADIATOR ............................................. 1 ..........REPLACES 06020 14653
HOSE, RADIATOR ............................................. 1 ..........REPLACES 06020 14541
HOSE BAND ...................................................... 6 ..........REPLACES 06020 14067
HOSE BAND ...................................................... 2 ..........REPLACES 06020 14056
HOSE BAND ...................................................... 2 ..........REPLACES 06020 14058
PIPE, RADIATOR ............................................... 1 ..........REPLACES 06020 13257
HOSE, RADIATOR ............................................. 2 ..........REPLACES 06020 14578
HOSE, RADIATOR ............................................. 1 ..........REPLACES 06020 14579
HOSE BAND ...................................................... 8 ..........REPLACES 06020 14900
HOSE BAND ...................................................... 4 ..........REPLACES 06020 14901
TANK, RESERVE
1
1
1
1
CAP, RESERVETANK
BRACKET, RESERVETANK
CUSHION, RUBBER
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 81
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
PAGE 82 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
ENGINE & RADIATOR ASSY. (S/N 3708270 AND ABOVE)
NO.
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
PART NO.
PART NAME
BOLT, HEX HEAD
BOLT, HEX HEAD
HOSE
QTY.
1
REMARKS
00171 06025
00171 08020
01999 01900
01936 02000
06055 15170
01936 00560
06055 15170
02691 00650
C23271 00103
00171 08020
06033 20112
02070 08000
02682 00700
06055 15132
C23583 01003
00171 10020
C23583 00003
00171 08020
00100 16030
00400 16000
00412 16000
2
1
HOSE
1
HOSE BAND
HOSE
HOSE BAND
HOSE
PIPE, BREATHER
BOLT, HEX HEAD
UBOLT
NUT, HEX HEAD
HOSE
HOSE BAND
ROD, CLAMPER
BOLT, HEX HEAD
ROD, CLAMPER
BOLT, HEX HEAD
BOLT, HEX HEAD
WASHER, SPRING
WASHER, PLAIN
2
1
1
1
1
2
1
2
1
2
1
2
1
1
1
1
1
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 83
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE OPERATING PANEL ASSY.
01673
PAGE 84 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENGINE OPERATING PANEL ASSY.
ENGINE OPERATING PANEL ASSY.
NO.
1
1
1
2
2
3
4
5
5
5
5
6
7
7
8
9
10
11
12
13
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
PART NO.
PART NAME
QTY.
REMARKS
C2352100203
C2352100213
C2352100223
0017106016
0017106015
0207006000
0602101000
0021008080
0030008000
0040008000
0041208000
0800250300
C2484000003
C2484000303
0017110025
8192183004
0010010035
0030010000
0041210000
C2355300404
C2355300414
C2355300104
0602180106
0030008000
0207006000
0041206000
0041206000
505015300
OPERATING PANEL .......................... 1 ......... S/N 3696506 AND BELOW
OPERATING PANEL .......................... 1 ......... S/N 3696507TO 3701673
OPERATING PANEL .......................... 1 ......... S/N 3701674 AND ABOVE
HEX. HEAD BOLT .............................. 8 ......... S/N 3701673 AND BELOW
HEX. HEAD BOLT .............................. 8 ......... S/N 3701674 AND ABOVE
HEX. NUT
4
1
2
2
2
2
BATTERY SWITCH
MACHINE SCREW
HEX. NUT
LOCK WASHER
PLAIN WASHER
THROTTLE HANDLE ......................... 1 ......... S/N 3701673 AND BELOW
SET FRAME ...................................... 1 ......... S/N 3701674TO 3708296
SET FRAME ...................................... 1 ......... S/N 3708297
HEX. HEAD BOLT
2
LINK, GOVERNOR ROD .................... 1 ......... S/N 3701673 AND BELOW
HEX. HEAD BOLT .............................. 1 ......... S/N 3701673 AND BELOW
HEX. NUT........................................... 1 ......... S/N 3701673 AND BELOW
PLAIN WASHER ................................ 2 ......... S/N 3701673 AND BELOW
GOVERNOR ROD .............................. 1 ......... S/N 1337508TO 3691258
GOVERNOR ROD .............................. 1 ......... S/N 3691259TO 3701673
GOVERNOR ROD .............................. 1 ......... S/N 3701673 AND BELOW
BALL JOINT ....................................... 2 ......... S/N 3701673 AND BELOW
HEX. NUT........................................... 2 ......... S/N 3701673 AND BELOW
HEX. NUT........................................... 2 ......... S/N 3701673 AND BELOW
PLAIN WASHER ................................ 2 ......... S/N 3701673 AND BELOW
PLAIN WASHER ................................ 2 ......... S/N 3701673 AND BELOW
SNAP PIN .......................................... 2 ......... UPTO S/N3701673;REPLACES 0605010502
PREHEAT BUTTON, AH25FB10 ........ 1 ......... S/N3696507~
EMERGENCY STOP BUTTON .......... 1 ......... S/N3701674~; AR22V2R01R
PREHEAT LAMP................................ 1 ......... REPLACES 0602102055
TACHOMETER................................... 1 ......... 25000-KX4110
CABLE, TACHOMETER ..................... 1 ......... 62500-KA4210L=3000
OIL PRESSURE GAUGE ................... 1 ......... 42000-KX1410
UNIT, OIL PRESSURE....................... 1 ......... 53000-AC0101
WATERTEMPERATURE GAUGE ...... 1 ......... 40000-KX0910
0601830448
0601831557
6008153730
0602120054
0602120156
0602122060
0602122200
0602123061
0602123206
0602121052
0602125060
0602115014
0601830710
0806410000
6008155390
615
UNIT, WATERTEMPERATURE .......... 1 ......... 51400-KS0600
CHARGING AMMETER ..................... 1 ......... 43000-KV0300
FUEL GAUGE .................................... 1 ......... 41000-KW0110
MONITOR........................................... 1 ......... V337660-0000
ENGINE SPEED SWITCH, S301T .... 1 ......... S/N3701674~
STOP BUTTON .................................. 1 ......... UPTO S/N3701673;REPLACES 0602104045
STARTER SWITCH ............................ 1 ......... UPTO S/N3701673;REPLACES 0602100049
KEY, STARTER SWITCH ................... 1 ......... UPTO S/N3701673;REPLACES 0602104045
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 85
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK OUTPUTTERMINAL ASSY.
OUTPUT TERMINAL ASSY.
UP
S/N3691259~
PAGE 86 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK OUTPUTTERMINAL ASSY.
OUTPUT TERMINAL ASSY.
NO.
1
1
PART NO.
C2231700203
8221860203
PART NAME
QTY.
REMARKS
SET BOARD, OUTPUT TERMINAL ................ 1 ......... S/N 3708296 AND BELOW
SET BOARD, OUTPUT TERMINAL ................ 1 ......... S/N 3708297 AND ABOVE
2
3
4
5
6
7
8
8
8
8
8
8
9
9
10
10
11
11
12
12
13
14
14
15
16
16
16
17
17
17
18
19
20
20
0801830404
0801830904
0039320000
0040020000
0041420000
3501860604
0019108040
0042308000
0042408000
0019110050
004231000
OUTPUTTERMINAL
HEX. HEAD BOLT
HEX. NUT
LOCK WASHER
PLAIN WASHER
TERMINAL PLATE
8
8
16
24
32
3
HEX. HEAD BOLT ........................................... 5 ......... S/N 3708296 AND BELOW
LOCK WASHER .............................................. 5 ......... S/N 3708296 AND BELOW
PLAIN WASHER ............................................. 5 ......... S/N 3708296 AND BELOW
BOLT, HEX HEAD ........................................... 5 ......... S/N 3708297 AND ABOVE
WASHER SPRING .......................................... 5 ......... S/N 3708297 AND ABOVE
WASHER PLAIN ............................................. 5 ......... S/N 3708297 AND ABOVE
CIRCUIT BREAKER, KM-51 265V 20A .......... 2 ......... S/N 3691259TO 3706720
CIRCUIT BREAKER, QOU120B 20A ............. 2 ......... S/N 3706721~; REPL. 0601805313
CIRCUIT BREAKER,KM-52 265V 50A ........... 3 ......... S/N 3691259TO 3706720
CIRCUIT BREAKER,QOU250B 50A ............... 3 ......... S/N 3706721 AND ABOVE
BRACKET, CIRCUIT BREAKER ..................... 1 ......... S/N 3691259TO 3706720
BRACKET, CIRCUIT BREAKER ..................... 1 ......... S/N 3706721AND ABOVE
RUBBER CUSHION ........................................ 1 ......... S/N 3691259TO 3706720
RUBBER CUSHION ........................................ 1 ......... S/N 3706721AND ABOVE
004241000
0601804887
0601808803
0601805840
0601808804
C1261600204
C3261600704
0223300200
0221200150
0017106020
0601812597
0601812598
0601811034
0027104015
0030004000
0041204000
C2237100403
C2237101103
C2237101103
0019112045
0042412000
0805009804
0805015604
HEX. HEAD BOLT
2
RECEPTACLE, 125 V, 20 AMP ....................... 2 ......... S/N 1337508TO 3691258
RECEPTACLE, 125 V, 20 AMP ....................... 2 ......... S/N 3691259 AND ABOVE
RECEPTACLE ................................................. 3 ......... REPLACES 0601812565
MACHINE SCREW
HEX. NUT
10
10
10
PLAIN WASHER
COVER, OUTPUT TERMINAL ........................ 1 ......... S/N 1337508TO 3691258
COVER, OUTPUT TERMINAL ........................ 1 ......... S/N 3691259 AND ABOVE
COVER, OUTPUT TERMINAL ........................ 1 ......... S/N 3708297 AND ABOVE
HEX. HEAD BOLT
PLAIN WASHER
RUBBERWASHER
2
2
2
RUBBERWASHER ......................................... 2 ......... S/N 3708297 AND ABOVE
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 87
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK OUTPUTTERMINAL ASSY.
OUTPUT TERMINAL ASSY.
UP
S/N3691259~
PAGE 88 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK OUTPUTTERMINAL ASSY.
OUTPUT TERMINAL ASSY.
NO.
21
22
23
23
23
24
25
26
27
28
29
30
31
32
34
35
36
PART NO.
PART NAME
HEX. NUT
SPRING
QTY.
2
2
REMARKS
020501200
0845043704
C2237100504
C2237100514
C2237101204
0017108020
C0237101504
0805015604
0845054204
0017110040
0601815324
0027104020
0601850275
0601851780
C2237101504
C2237400104
0017106020
COVER ............................................................ 1 ......... S/N 1337508TO 3691258
COVER ............................................................ 1 ......... S/N 3691259 AND ABOVE
COVER ............................................................ 1 ......... S/N 3708297 AND ABOVE
HEX. HEAD BOLT
9
COVER, OUTPUT TERMINAL ........................ 1 ......... S/N 3691259 AND ABOVE
RUBBERWASHER ......................................... 1 ......... S/N 3691259 AND ABOVE
COLLER .......................................................... 2 ......... S/N 3691259 AND ABOVE
HEX. HEAD BOLT ........................................... 2 ......... S/N 3691259 AND ABOVE
TERMINAL BOARD, TS22P ............................ 1 ......... S/N3696507 AND ABOVE
MACHINE SCREW ......................................... 2 ......... S/N3696507 AND ABOVE
GROMMET ..................................................... 1 ......... S/N3696507 AND ABOVE
GROMMET ..................................................... 2 ......... S/N3700674 AND ABOVE
COVER ............................................................ 1 ......... S/N 3708297 AND ABOVE
BRACKET
1
BOLT, HEX HEAD ........................................... 2 ......... S/N 3708297 AND ABOVE
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 89
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300 SSK ACTUATOR ASSY.
ACTUATOR ASSY. (S/N3701674~)
PAGE 90 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300 SSK ACTUATOR ASSY.
ACTUATOR ASSY. (S/N 3701674~)
NO.
1
2
PART NO.
DYNC110240000024
DYNC182
PART NAME
QTY.
REMARKS
ACTUATOR....................................... 1 ............. REPLACES 0602150091
LEVER ............................................. 1 ............. REPLACES 0602211090
3
4
5
5
5
5
6
7
8
9
9
9
10
10
10
C1356200004
0012310030
0010306035
0207006000
0040006000
0041206000
0602211091
0602180190
0602211092
0010106025
0207006000
0041206000
0010106025
0207006000
0041206000
BRACKET, ACTUATOR
HEX. HEAD BOLT
HEX. HEAD BOLT
HEX. NUT
LOCKWASHER
PLAIN WASHER
ROD
BALL JOINT
HEX. NUT
HEX. HEAD BOLT
HEX. NUT
PLAIN WASHER
HEX.HEAD BOLT
HEX. NUT
1
4
4
4
4
4
1
2
2
1
1
1
1
1
4
PLAIN WASHER
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 91
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300 SSK BATTERY ASSY.
BATTERY ASSY.
PAGE 92 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300 SSK BATTERY ASSY.
BATTERY ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
2
2
1
2
2
2
2
1
1
1
1
1
4
4
2
2
REMARKS
0168614551
0805000804
3972250004
0805002904
0037808000
0040008000
0041208000
C2347600404
C2347600104
C2347600204
C2347600304
C2347200004
0010010030
0030010000
0845040414
0845041304
0602220204
BATTERY
BATTERY SHEET
BATTERY BAND
BATTERY BOLT
WING NUT
LOCK WASHER
PLAIN WASHER
BATTERY CABLE
BATTERY CABLE
BATTERY CABLE
BATTERY CABLE
EARTH CABLE
HEX. HEAD BOLT
HEX. NUT
9
10
11
12
13
14
15
16
17
TERMINAL CAP +
TERMINAL CAP -
BATTERY SENSOR
1
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 93
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK MUFFLER ASSY.
MUFFLER ASSY.
PAGE 94 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
2
3
3
PART NO.
PART NAME
MUFFLER
HEX. HEAD BOLT
QTY.
1
4
REMARKS
C2331100002
0019210025
C2334000003
C2234000503
EXHAUST PIPE .............................................. 1 ......... UP TO S/N 3708296
EXHAUST PIPE .............................................. 1 ......... S/N 3708297 AND ABOVE
4
5
5
5
6
6
6
6
7
7
7
7
8
9
6150115751
7502356004
C1334200304
6150115751
0010312050
0030312000
0040012000
0041212000
0010112055
0030012000
0040012000
0041212000
C2331300004
0017108020
GASKET ......................................................... 1 ......... REPLACES 0602320142
GASKET ......................................................... 1 ......... S/N 1337508TO 3691258
GASKET ......................................................... 1 ......... S/N 3691259 TO S/N 3708296
GASKET ......................................................... 1 ......... S/N 3708297 ABOVE
HEX. HEAD BOLT
HEX. NUT
4
4
4
8
4
4
4
8
2
4
LOCK WASHER
PLAIN WASHER
HEX. HEAD BOLT
HEX. NUT
LOCK WASHER
PLAIN WASHER
COVER
HEX. HEAD BOLT
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 95
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 96 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
1
2
2
3
4
4
5
6
7
8
9
10
10
11
12
13
14
15
16
17
18
19
20
21
21
22
22
23
PART NO.
PART NAME
QTY.
REMARKS
C2364000303
C2364000313
0605505030
0601850590
0810105400
0264100485
0264100525
0605515079
0605503023
0802120604
0605501050
0602021155
0027104010
0022905015
8195523104
0805003414
0017108020
0037908000
0222100300
0130206000
3515512014
0603325011
0132006000
0845039604
0191302000
0191302300
0191302240
0191302800
0605515109
FUELTANK ..................................................... 1 ......... S/N 1337508TO 2691258
FUELTANK ..................................................... 1 ......... S/N 2691259 AND ABOVE
CAP, FUEL TANK ............................................ 1 ......... REPLACES 0605505005
KEY, FUEL TANK ............................................ 1 ......... REPLACES 0601850505
FUEL FILTER
HOSE, FUEL GAUGE
1
1
HOSE, FUEL GAUGE ..................................... 1 ......... S/N 3708297 AND ABOVE
HOSE BAND
FUEL SENSOR ............................................... 1 ......... FF-9
PACKING
UNIT FUEL...................................................... 1 ......... 52000-KA9810
PACKING ........................................................ 1 ......... 52391-KW3700
MACHINE SCREW ......................................... 5 ......... S/N 3691259 AND ABOVE
MACHINE SCREW ......................................... 5 ......... S/N 1337508TO 2691258
2
1
TANK BAND
2
4
2
2
6
1
1
PAD, TANK BAND
HEX. HEAD BOLT
HEX. NUT
TANK SHEET
STREET ELBOW
DRAIN PIPE
VALVE ............................................................. 1 ......... BBS-77-15 PT1/2
PLUG
RUBBER SEAL
SUCTION HOSE ............................................. 1 ......... UP TO S/N 1337973
SUCTION HOSE ............................................. 1 ......... FROM S/N 1337974
RETURN HOSE .............................................. 1 ......... UP TO S/N 1337973
RETURN HOSE .............................................. 1 ......... FROM S/N 1337974
1
1
HOSE BAND
4
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 97
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (UPTO S/N 3708296)
ENCLOSURE ASSY
THE PART NUMBER ABOVE INDICATES DEFAULT COLOR
OF ORANGE. TO ORDER WITH DIFFERENT COLOR,
PLEASE ADD THE FOLLOWING LETTERS WITH THE PART
NUMBER:
MQGR-GRAY
MQGRN-GREEN
MQW-WHITE
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 98 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (UPTO S/N 3708296)
ENCLOSURE ASSY. (UP TO S/N 3708296)
NO.
1
1
1
2
3
4
5
5
6
7
7
7
7
8
9
10
10
11
12
13
14
15
16
16
17
17
17
17
18
18
18
18
19
19
20
21
22
22
23
23
24
25
25
26
27
PART NO.
PART NAME
QTY.
REMARKS
C2414000002
C2414000402
C2415000002
C3414100104
C2414100004
0019208020
C2414600004
C2494000004
0017108020
C2424000402
C2425000202
C2425000212
C2494100003
0019210025
C2424200003
C2424200104
C2494100104
0019208020
0845042703
0019208020
C2424200203
0019208020
C2434000102
C2434000112
0010114050
0030014000
0040014000
0041214000
0010114040
0030014000
0040014000
0041214000
C2444000302
C2494300204
0019210025
0017110025
C2444300004
C2494300004
C2444300203
C2494300304
0207008000
C2444300104
C2494300104
0017108020
0019208020
BASE .............................................................. 1 ......... S/N 1337508TO 3691258
BASE .............................................................. 1 ......... S/N 3691259TO 3701673
BASE .............................................................. 1 ......... S/N 3701674TO 3708296
FLOOR PANEL
FLOOR PANEL
HEX. HEAD BOLT
DUCT
LINING ............................................................ 1 ......... TO S/N 3708296
HEX. HEAD BOLT
FRONT FRAME .............................................. 1 ......... S/N3691259TO 3701673
FRONT FRAME .............................................. 1 ......... S/N3701674TO 3705209
FRONT FRAME .............................................. 1 ......... S/N3705210TO 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
HEX. HEAD BOLT
COVER, FRONT FRAME
COVER, FRONT FRAME
LINING
HEX. HEAD BOLT
FILLER BRACKET
HEX. HEAD BOLT
COVER, FRONT FRAME
HEX. HEAD BOLT
CENTER FRAME ............................................ 1 ......... UP TO S/N 1337973
CENTER FRAME ............................................ 1 ......... S/N 1337974TO 3708296
HEX. HEAD BOLT
HEX. NUT
LOCK WASHER
PLAIN WASHER
HEX. HEAD BOLT
HEX. NUT
LOCK WASHER
PLAIN WASHER
REAR FRAME
LINING
HEX. HEAD BOLT
HEX. HEAD BOLT
COVER, REAR FRAME
LINING
DUCT .............................................................. 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
HEX. NUT
PANEL
LINING
1
1
14
1
4
8
1
1
1
26
1
4
1
14
4
4
4
8
8
8
8
16
1
1
4
3
1
1
15
1
1
6
14
HEX. HEAD BOLT
HEX. HEAD BOLT
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 99
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (UPTO S/N 3708296)
ENCLOSURE ASSY. (UP TO S/N 3708296)
THE PART NUMBER ABOVE INDICATES DEFAULT COLOR
OF ORANGE. TO ORDER WITH DIFFERENT COLOR,
PLEASE ADD THE FOLLOWING LETTERS WITH THE PART
NUMBER:
MQGR-GRAY
MQGRN-GREEN
MQW-WHITE
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 100 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (UPTO S/N 3708296)
ENCLOSURE ASSY. (UP TO S/N 3708296)
NO.
28
29
30
31
32
33
34
35
35
36
37
38
39
40
41
42
43
43
44
44
45
46
47
48
48
49
50
50
50
51
51
52
53
53
53
53
53
53
54
54
54
55
55
56
56
PART NO.
PART NAME
QTY.
1
1
2
12
1
4
1
4
4
1
1
4
8
1
1
4
REMARKS
C2444200003
C2444200103
8225147004
0037906000
B9114500104
0207006000
B9114000102
0021806016
0030006000
C3444700004
8195146304
0845050704
0207006000
0805011304
0805011204
0207006000
M9110100304
0845045004
M9110100304
0845045004
0019208020
0601850097
0025008025
C2464100002
C2494500004
0800251701
0025006016
0042306000
0042406000
C2464200002
C2494500104
0019208020
C2454200402
C2454200412
C2454200422
C2454200432
C2454200442
C2454200452
0019108065
0042308000
0042408000
C2454000203
C2494400404
C2454000303
C2494400604
DOOR, REAR FRAME
DOOR, REAR FRAME
WINDOW PLATE
HEX. NUT
DOOR POCKET
HEX. NUT
DOOR HANDLE
MACHINE SCREW
HEX. NUT
DOOR ROD
DOOR ROD
STAY
HEX. NUT
STOPPER, DOOR
STOPPER, DOOR
HEX. NUT
HINGE ............................................................. 2 ......... REPLACES 0845047104
WASHER
HINGE ............................................................. 2 ......... REPLACES 0845047204
WASHER
HEX. HEAD BOLT
STOPPER
MACHINE SCREW
ROOF PANEL.................................................. 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
FILLER COVER
MACHINE SCREW
LOCK WASHER
PLAIN WASHER
ROOF PANEL.................................................. 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
2
2
6
2
2
1
2
2
2
HEX. HEAD BOLT
32
SPLASHER PANEL......................................... 1 ......... UP TO S/N 1337973
SPLASHER PANEL......................................... 1 ......... FROM S/N 1337974 TO 3691258
SPLASHER PANEL......................................... 1 ......... S/N 3691259TO 3696506
SPLASHER PANEL......................................... 1 ......... S/N3696507TO 3700673
SPLASHER PANEL......................................... 1 ......... S/N3700674TO 3706720
SPLASHER PANEL......................................... 1 ......... S/N3706721TO 3708296
HEX. HEAD BOLT
LOCK WASHER
PLAIN WASHER
SIDE DOOR .................................................... 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
SIDE DOOR .................................................... 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
6
6
6
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 101
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (UPTO S/N 3708296)
ENCLOSURE ASSY. (UP TO S/N 3708296)
THE PART NUMBER ABOVE INDICATES DEFAULT COLOR
OF ORANGE. TO ORDER WITH DIFFERENT COLOR,
PLEASE ADD THE FOLLOWING LETTERS WITH THE PART
NUMBER:
MQGR-GRAY
MQGRN-GREEN
MQW-WHITE
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 102 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (UPTO S/N 3708296)
ENCLOSURE ASSY. (UP TO S/N 3708296)
NO.
57
57
58
58
59
59
60
60
61
61
62
62
63
64
65
66
66
67
67
68
68
69
70
71
72
73
74
75
76
PART NO.
PART NAME
QTY. REMARKS
C2454000003
C2494400004
C2454000103
C2494400204
C2494400504
C2494400504
C2454300304
C2494400704
C2454300004
C2494400104
C2454300104
C2494400304
0207008000
B9114000002
0825007362
0021806016
0030006000
0845046904
0845045004
0845047004
0845045004
0019208020
0601850097
0021008025
0845031504
0600500090
0021106016
C2464500604
C2464500704
SIDE DOOR .................................................... 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
SIDE DOOR .................................................... 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
DUCT .............................................................. 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
DUCT .............................................................. 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
DUCT .............................................................. 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
DUCT .............................................................. 1 ......... TO S/N 3708296
LINING ............................................................ 1 ......... TO S/N 3708296
HEX. NUT
28
4
3
28
28
6
6
5
5
25
8
DOOR HANDLE
DOOR HANDLE
MACHINE SCREW
HEX. NUT
HINGE
WASHER
HINGE
WASHER
HEX. HEAD BOLT
STOPPER
MACHINE SCREW
CAP
8
14
2
EMBLEM
MACHINE SCREW
4
GUTTER ......................................................... 2 ......... S/N3707481TO S/N3708296
GUTTER ......................................................... 2 ......... S/N3707481TO S/N3708296
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 103
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (S/N 3708297~)
ENCLOSURE ASSY. (
THE PART NUMBER ABOVE INDICATES DEFAULT COLOR
OF ORANGE. TO ORDER WITH DIFFERENT COLOR,
PLEASE ADD THE FOLLOWING LETTERS WITH THE PART
NUMBER:
MQGR-GRAY
MQGRN-GREEN
MQW-WHITE
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 104 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (S/N 3708297~)
ENCLOSURE ASSY. (S/N 3708297~)
NO.
1
2
3
4
5
5
6
7
PART NO.
PART NAME
BASE
PANEL, FLOOR
PANEL, FLOOR
BOLT, HEX HEAD
DUCT
QTY.
1
1
1
14
1
1
4
1
1
8
1
1
1
26
1
4
1
14
1
4
4
4
8
8
8
8
16
1
1
4
3
1
1
1
1
15
1
REMARKS
C24140 01002
C34141 00104
C241410004
00192 08020
C24145 00204
C24940 00004
00171 08020
C24240 01702
C24941 00703
00192 10025
C24242 00003
C24242 00104
C24941 00104
00192 08020
08450 42703
00192 08020
C24242 00203
00192 08020
C24340 01002
00101 14050
00300 14000
00400 14000
00412 14000
00101 14040
00300 14000
00400 14000
00412 14000
C24440 00302
C24943 00204
00192 10025
00171 10025
C24443 00004
C24943 00904
C24443 00803
C24943 00904
02070 08000
C24443 00104
C24943 00104
00171 08020
00192 08020
C24442 00003
C24442 00103
82251 47004
00379 06000
B91145 00104
02070 06000
LINING
BOLT, HEX HEAD
FRONT, FRAME
LINING
BOLT, HEX HEAD
COVER, FRONT FRAME
COVER, FRONT FRAME
LINING
BOLT, HEX HEAD
BRACKET, FILLER
BOLT, HEX HEAD
COVER, FRONT FRAME
BOLT, HEX HEAD
FRAME, CENTER
BOLT, HEX HEAD
NUT, HEX
WASHER, SPRING
WASHER, PLAIN
BOLT, HEX HEAD
NUT, HEX
WASHER, SPRING
WASHER, PLAIN
FRAME, REAR
LINING
BOLT, HEX HEAD
BOLT, HEX HEAD
COVER, REAR FRAME
LINING
7
8
9
10
10
11
12
13
14
15
16
17
17
17
17
18
18
18
18
19
19
20
21
22
22
23
23
24
25
25
26
27
28
29
30
31
32
33
DUCT
LINING
NUT, HEX
PANEL
LINING
1
6
14
1
1
2
12
1
BOLT, HEX HEAD
BOLT, HEX HEAD
DOOR, REAR FRAME
DOOR, REAR FRAME
PLATE, WINDOW
NUT, HEX
POCKET, DOOR
NUT, HEX
4
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 105
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (S/N 3708297~)
ENCLOSURE ASSY. (
THE PART NUMBER ABOVE INDICATES DEFAULT COLOR
OF ORANGE. TO ORDER WITH DIFFERENT COLOR,
PLEASE ADD THE FOLLOWING LETTERS WITH THE PART
NUMBER:
MQGR-GRAY
MQGRN-GREEN
MQW-WHITE
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 106 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (S/N 3708297~)
ENCLOSURE ASSY. (S/N 3708297~)
NO.
34
35
35
36
37
38
39
40
41
42
43
43
44
44
45
46
47
48
48
49
50
50
50
51
51
52
53
54
54
54
55
55
56
56
57
57
58
58
59
59
60
60
61
61
62
62
PART NO.
PART NAME
HANDLE, DOOR
SCREW, MACHINE
NUT, HEX
ROD, DOOR
ROD, DOOR
STAY
QTY.
1
4
4
1
1
4
8
1
1
4
2
2
2
2
6
2
2
1
1
1
2
2
2
1
1
32
1
6
6
6
1
1
1
1
1
1
1
1
1
1
1
1
2
2
1
1
REMARKS
B91140 00102
00218 06016
00300 06000
C34447 00004
81951 46304
08450 50704
02070 06000
08050 11304
08050 11204
02070 06000
08450 47104
08450 45004
08450 47204
08450 45004
00192 08020
06018 50097
00254 08025
C24641 00402
C24945 00804
08002 51701
00250 06015
00423 06000
00424 06000
C24642 00502
C24945 00904
00192 08020
C24542 01402
00191 08065
00423 08000
00424 08000
C24540 02603
C24944 06004
C24540 02703
C24944 06204
C24540 02803
C24944 05504
C24540 03003
C24944 05804
C24543 02704
C24944 06104
C24543 02704
C24944 06104
C24543 02704
C24944 06104
C24543 02704
C24944 06104
NUT, HEX
STOPPER, DOOR
STOPPER, DOOR
NUT, HEX
HINGE
WASHER
HINGE
WASHER
BOLT, HEX HEAD
STOPPER
SCREW, MACHINE
PANEL, ROOF
LINING
COVER, FILLER
SCREW, MACHINE
WASHER, SPRING
WASHER, PLAIN
PANEL, ROOF
LINING
BOLT, HEX HEAD
PANEL, SPLASHER
BOLT, HEX HEAD
WASHER, SPRING
WASHER, PLAIN
DOOR, SIDE
LINING
DOOR, SIDE
LINING
DOOR, SIDE
LINING
DOOR, SIDE
LINING
DUCT
LINING
DUCT
LINING
DUCT
LINING
DUCT
LINING
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 107
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (S/N 3708297~)
ENCLOSURE ASSY. (S/N 3708297~)
THE PART NUMBER ABOVE INDICATES DEFAULT COLOR
OF ORANGE. TO ORDER WITH DIFFERENT COLOR,
PLEASE ADD THE FOLLOWING LETTERS WITH THE PART
NUMBER:
MQGR-GRAY
MQGRN-GREEN
MQW-WHITE
THE SERIAL NUMBER MAY BE REQUIRED.
PAGE 108 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK ENCLOSURE ASSY. (S/N 3708297~)
ENCLOSURE ASSY. (S/N 3708297~)
NO.
63
64
65
66
66
67
67
68
68
69
70
71
72
73
74
75
77
78
79
PART NO.
PART NAME
NUT, HEX
HANDLE, DOOR
HANDLE, DOOR
SCREW, MACHINE
NUT, HEX
HINGE
WASHER
HINGE
WASHER
BOLT, HEX HEAD
STOPPER
SCREW, MACHINE
CAP
EMBLEM
SCREW, MACHINE
QTY.
28
4
REMARKS
02070 08000
B91140 00002
08250 07362
00218 06016
00300 06000
08450 46904
08450 45004
08450 47004
08450 45004
00192 08020
06018 50097
00254 08025
08450 31504
06005 00090
00211 06016
C24645 00204
0019208020
C1425700004
0019206015
3
28
16
6
6
5
5
25
8
8
15
2
4
2
4
1
GUTTER
HEX. HEAD BOLT
RADIATOR PANEL
HEX. HEAD BOLT
4
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 109
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK RUBBER SEAL ASSY.
RUBBER SEAL ASSY.
PAGE 110 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK RUBBER SEAL ASSY.
RUBBER SEAL ASSY.
NO.
1
2
3
4
5
6
7
7
PART NO.
PART NAME
QTY.
REMARKS
0228901250
0228901090
0228900650
0228901030
0229201400
0229201300
0228800705
0221200705
0228801200
0228100120
0228100510
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
6
4
2
4
4
1
RUBBER SEAL ............................................... 2 ......... S/N3691259TO 3701673
RUBBER SEAL ............................................... 2 ......... S/N3701674 AND ABOVE
RUBBER SEAL
RUBBER SEAL
RUBBER SEAL
8
9
10
2
4
4
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 111
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK OIL PIPING ASSY.
OIL PIPING ASSY.
PAGE 112 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK OIL PIPING ASSY.
OIL PIPING ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
PUMP
BRACKET, PUMP
HEX., HEAD BOLT
HEX., HEAD BOLT
BUSHING
NIPPLE
VALVE
HOSE JOINT
HOSE
HOSE BAND
HOSE
QTY.
REMARKS
0602023040
C2324400004
0017110025
0017106025
7522054204
0131506000
0120006005
3972027104
0191600900
0605515074
0193301200
0605515004
1
1
2
5
1
1
1
2
1
2
1
1
9
10
11
12
HOSE BAND
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 113
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 114 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
1
1
1
2
PART NO.
PART NAME
QTY.
REMARKS
0800655603
C155100503
C155200403
B155200103
C952210003
DECAL; HANDLING PROCED.;S2763A
DECAL;HANDLING PROCED.;C1510050
DECAL;HANDLING PROCED.;C1520040
DECAL;CAUTION;B15200010
DECAL;CAUTION;C92210000
1
1
1
2
2
S/N3691259TO 3696506
S/N3696507TO 3701673
S/N3701674~
S/N3696507TO 3701673
S/N3701674~
2
CONTROL BOX GROUP
3
4
5
6
7
8
9
10
11
12
13
14
15
0800520100
0800520904
0800520814
0840624504
0840624704
0840624604
0840624804
B9531100604
C0551000903
C2551000004
C2561101903
C9502400004
0600500091
PLATE; ON-OFF .............................................. 1 ......... AT-202
PLATE; AMMETER CHNG.-OVR SWITCH ..... 1 ......... N-2438
PLATE;VOLTMETER CHNG.-OVR SWITCH .. 1 ......... N-2439
DECAL; CIRCUIT BREAKER .......................... 1 ......... S-3031
DECAL; PILOT LAMP ..................................... 1 ......... S-3033
DECAL; PANEL LIGHT SWITCH..................... 1 ......... S-3032
DECAL;VOLTAGE REGULATOR..................... 1 ......... S-3034
DECAL;WARNING .......................................... 1 ......... B93110060
DECAL; SETTING FOR OUTPUT VOLTAGE. . 1 ......... C0510009
DECAL; SAFETY INSTRUCTIONS ................. 1 ......... C25100000
DECAL;WHISPERWATT 300 .......................... 1 ......... C26110190
DECAL; HIGH IDLE SPEED, C90240000........ 1 ......... S/N3701674~
DECAL; ENGINE CONTROLLER .................... 1 ......... S/N3696507~
ENGINE OPERATING PANEL GROUP
19
19
20
20
21
22
23
23
5-1
5-2
5-3
5-4
5-5
5-6
5-7
5-8
0840625004
C155200013
0840625104
C9501400304
C0551000504
C0551000704
C0551000804
0840647804
0840614104
0840619904
B4551000103
B9511100304
B9511100404
B9531100504
C0551000404
C1551000404
DECAL; PREHEAT LAMP, S-3036 .................. 1 ......... S/N3691259TO 3701673
DECAL; OPERATING PANEL, C15200001...... 1 ......... S/N3701674~
DECAL; STARTER SWITCH, S-3037 .............. 1 ......... S/N3691259TO 3696506
DECAL;PREHEAT BUTTON, C90140030 ....... 1 ......... S/N3696507TO 3701673
DECAL; BATTERY SWITCH ........................... 1 ......... C05100050
DECAL;LOW-HIGH, C05100070 ..................... 1 ......... S/N3691259TO 3701673
DECAL;STOP BUTTON, C05100080.............. 1 ......... S/N3691259TO 3696506
DECAL; EMERGENCY STOP, S4100 ............. 1 ......... S/N3696507TO 3701673
DECAL; GROUND
DECAL;DANGER
DECAL; RECEPT. & CIRCT. BREAKER
DECAL;WARNING
DECAL;WARNING
1
1
1
1
1
1
1
2
S-2635
S-2731
B45100010
B91110030
B91110040
B93110050
C05100040
C15100040
DECAL;WARNING
DECAL; 3-PHASE OUTPUT TERMINAL
DECAL; 240/139VOLT
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 115
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 116 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK NAME PLATE AND DECALS
NAMEPLATE AND DECALS
NO.
PART NO.
PART NAME
ENGINE & RADIATOR GROUP
QTY.
REMARKS
16
17
18
6360610304
B9504000404
B9504100104
DECAL;WATER......................................................... 1............ S-1880
DECAL;WARNING .................................................... 2............ B90400040
DECAL;WARNING .................................................... 1............ B90410010
OUTPUT TERMINAL GROUP
24
25
26
26
27
28
29
30
31
31
0840614104
0840619904
B4551000103
C1551000803
B9511100304
B9511100404
B9531100504
C0551000404
C1551000404
9039209064
DECAL; GROUND ..................................................... 1............ S-2635
DECAL;DANGER...................................................... 1............ S-2731
DECAL; RECEPT. & CIRCT. BREAKER,B45100010 . 1............ S/N3691259TO 3706720
DECAL; RECEPT. & CIRCT. BREAKER,C15100080 . 1............ S/N3706721AND ABOVE
DECAL;WARNING .................................................... 1............ B91110030
DECAL;WARNING .................................................... 1............ B91110040
DECAL;WARNING .................................................... 1............ B93110050
DECAL; 3-PHASE OUTPUT TERMINAL................... 1............ C05100040
DECAL;240/139VOLT, C15100040 ........................... 2............ UPTO S/N3696506
DECAL; START CONTACT, S4468 ............................ 1............ S/N3696507 AND ABOVE
BATTERY GROUP
32
33
34
0800689404
0800689504
C9505300004
DECAL; + .................................................................. 1............ S-2090
DECAL; - ................................................................... 1............ S-2091
DECAL;CAUTION ..................................................... 1............ C90530000
MUFFLER GROUP
DECAL;WARNING .................................................... 1............ B90420000
35
B9504200004
FUEL TANK GROUP
36
37
38
1320620904
6360620004
B9504500004
DECAL; DIESEL FUEL ............................................. 1............ S-1756
DECAL; FUEL DRAIN PLUG..................................... 1............ S-1883
DECAL;WARNING .................................................... 1............ B90450000
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 117
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
PAGE 118 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
DCA-300SSK NAMEPLATE AND DECALS
NAMEPLATE AND DECALS
NO.
PART NO.
PART NAME
QTY.
REMARKS
ENCLOSURE GROUP
39
40
41
42
43
44
45
46
46
47
47
48
49
50
50
51
1320610603
1320621504
0840625902
DECAL;WATER-OIL .................................................. 1............ S-1760
DECAL; SUPPORT HOOK........................................ 2............ S-2257
DECAL; MQ............................................................... 1............ S-3057
DECAL;CAUTION ..................................................... 1............ B90400030
DECAL;WARNING .................................................... 1............ B93110060
STRIPE
STRIPE
STRIPE ..................................................................... 1............ TO S/N 3708296
STRIPE ..................................................................... 1............ S/N 3708297 AND ABOVE
STRIPE ..................................................................... 1............ TO S/N 3708296
STRIPE ..................................................................... 2............ S/N 3708297AND ABOVE
STRIPE
STRIPE
B9504000304
B9531100604
C2561101003
C2561101603
C2561101303
C2561102003
C2561101404
C2561102103
C2561101204
C2561101803
C2561101503
C2561102203
C2561101703
1
1
2
1
STRIPE ..................................................................... 1............ TO S/N 3708296
STRIPE ..................................................................... 1............ S/N 3708297 AND ABOVE
STRIPE ..................................................................... 1............ TO S/N 3708296
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 119
Download from Www.Somanuals.com. All Manuals Search And Download.
TERMS AND CONDITIONS OF SALE — PARTS
Effective: October 1, 2002
PAYMENT TERMS
5. Parts must be in new and resalable
condition,intheoriginalMultiquippack-
age (if any), and with Multiquip part
numbersclearlymarked.
Multiquip reserves the right to quote and sell
directtoGovernmentagencies,andtoOriginal
Equipment Manufacturer accounts who use
our products as integral parts of their own
products.
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being
replaced by another item, it is
obsolete.)
A$35.00surchargewillbeaddedtotheinvoice
forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
b. Any parts with a limited shelf life
(such as gaskets, seals, “O” rings,
and other rubber parts) that were
purchased more than six months
priortothereturndate.
LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
Multiquip shall not be liable here under for
damagesinexcessofthepurchasepriceofthe
itemwithrespecttowhichdamagesareclaimed,
andinnoeventshallMultiquipbeliableforloss
of profit or good will or for any other special,
consequentialorincidentaldamages.
TheminimumchargeforordersfromMultiquip
is $15.00 net. Customers will be asked for
instructionsregardinghandlingofordersnot
meetingthisrequirement.
c. Anylineitemwithanextendeddealer
netpriceoflessthan$5.00.
RETURNEDGOODSPOLICY
d. Special order items.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Nowarranties,expressorimplied,aremadein
connectionwiththesaleofpartsortradeacces-
soriesnorastoanyenginenotmanufactured
byMultiquip.Suchwarrantiesmadeinconnec-
tion with the sale of new, complete units are
madeexclusivelybyastatementofwarranty
packagedwithsuchunits,andMultiquipnei-
ther assumes not authorizes any person to
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. The sender will be notified of any
materialreceivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Such material will be held for five
workingdaysfromnotification,pending
instructions. If a reply is not received
within five days, the material will be
returnedtothesenderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. Incaseswhereanitemisaccepted,for
which the original purchase document
cannotbedetermined,thepricewillbe
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cific date and all orders received on or after
that date will be billed at the revised price.
Rebatesforpricedeclinesandaddedcharges
forpriceincreaseswillnotbemadeforstock
onhandatthetimeofanypricechange.
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All
partsmustbereturnedfreightprepaidto
Multiquip’sdesignatedreceivingpoint.
PAGE 120 — DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD) — REV. #4 (03/27/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
DCA-300SSK SERIES — PARTS AND OPERATION MANUAL (STD)— REV. #4 (03/27/06) — PAGE 121
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVE THE MODEL AND SERIAL
NUMBER ON-HAND WHEN CALLING
PARTS DEPARTMENT
800-427-1244 or 310-537-3700
FAX: 800-672-7877 or 310-637-3284
SERVICE DEPARTMENT
800-421-1244
FAX: 310- 537-4259
TECHNICAL ASSISTANCE
800-478-1244
FAX: 310- 631-5032
WARRANTY DEPARTMENT
888-661-4279, or 310-661-4279
FAX: 310- 537-1173
Manufactured for Multiquip Inc.
by
DENYO CO., LTD, JAPAN
MULTIQUIP INC.
POST OFFICE BOX 6254
CARSON, CA 90749
310-537-3700 • 800-421-1244
FAX:310-537-3927
WWW:multiquip.com
Atlanta • Boise • Dallas • Houston • Newark
Quebec, Canada • Manchester, UK • Rio De Janiero, BR • Guadalajara, MX
Download from Www.Somanuals.com. All Manuals Search And Download.
|