OPERATION AND PARTS MANUAL
MULTIQUIP/STOW
MODEL: G-55H
GASOLINE VIBRATOR
(5.5 HP GASOLINE ENGINE)
MODEL #
SERIAL #
Revision #0 (03/07/06)
THIS MANUAL MUST ACCOMPANYTHE EQUIPMENT AT ALLTIMES.
P/N 36397
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR —TABLE OF CONTENTS
HondaGX160K1QX2Engine
Air Cleaner (Dual) Assembly.............................. 32-33
Camshaft Assembly ........................................... 34-35
Carburetor Assembly ......................................... 36-37
Control Assembly ............................................... 38-39
G-55H GASOLINE VIBRATOR
Proposition 65Warning ..................................................... 2
Table Of Contents ............................................................. 3
Parts Ordering Procedures ............................................... 4
Specifications ................................................................... 5
Safety Message Alert Symbols .................................... 6-7 Crankcase Cover Assembly............................... 40-41
Rules For Safe Operation .............................................. 8-9
Operation and Safety Decals.......................................... 10
General Information ........................................................ 11
Major Components ......................................................... 12
Engine Components ....................................................... 13
Inspection .................................................................. 14-15
Startup Procedures ................................................... 16-17
Shutdown Procedures .................................................... 17
Operation ................................................................... 18-19
Maintenance .............................................................. 20-21
Troubleshooting (Gasoline Engine) ................................. 23
Explanation Of Codes In Remarks Column .................... 24
Suggested Spare Parts .................................................. 25
Crankshaft/Balancer Assembly .......................... 42-43
Cylinder Barrel Assembly................................... 44-45
Cylinder Head Assembly.................................... 46-47
Fan Cover Assembly .......................................... 48-49
Flywheel Assembly ............................................ 50-51
Fuel Tank Assembly ........................................... 52-53
Ignition Coil Assembly ........................................ 54-55
Muffler Assembly ............................................... 56-57
Piston Assembly................................................. 58-59
Recoil Starter Assembly..................................... 60-61
Gasket Kit Assembly .......................................... 62-63
Labels Assembly ................................................ 64-65
Terms and Condition Of Sale
—
Parts .................... 66
COMPONENT DRAWINGS
Nameplate and Decals .............................................. 26-27
Eccentric and Body Assembly .................................. 28-29
Pivot Assembly ......................................................... 30-31
Specification and part number
are subject to change without
notice.
NOTE
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 3
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS ORDERING PROCEDURES
Ordering parts has never been easier!
Choose from three easy options:
Best Deal!
Order via Internet (Dealers Only)
Orderpartson-lineusingMultiquip’sSmartEquipwebsite!
:
If you have an MQ Account, to obtain a
Username and Password, E-mail us at:
■
■
■
View Parts Diagrams
Order Parts
PrintSpecificationInformation
To obtain an MQ Account, contact your
District Sales Manager for more information.
Use the internet and qualify for a 5% Discount
on Standard orders for all orders which include
complete part numbers.*
Gotowww.multiquip.comandclickon
to log in and save!
Order Parts
Note: Discounts Are Subject To Change
Fax your order in and qualify for a 3% Discount
on Standard orders for all orders which include
complete part numbers.*
Order via Fax (Dealers Only)
:
All customers are welcome to order parts via Fax.
Domestic (US) Customers dial:
1-800-6-PARTS-7 (800-672-7877)
Note: Discounts Are Subject To Change
Domestic (US) Dealers Call:
1-800-427-1244
Order via Phone:
Non-Dealer Customers:
International Customers should contact
their local Multiquip Representatives for
Parts Ordering information.
Contact your local Multiquip Dealer for
parts or call 800-427-1244 for help in
locating a dealer near you.
When ordering parts, please supply:
❒
❒
❒
❒
❒
❒
Dealer Account Number
❒
Specify Preferred Method of Shipment:
✓
Fed Ex/UPS
✓ DHL
Dealer Name and Address
■
■
Priority One
Ground
✓
Truck
Shipping Address (if different than billing address)
Return Fax Number
Applicable Model Number
■ Next Day
■
Second/ThirdDay
Quantity, Part Number and Description of Each Part
Unless otherwise indicated by customer, all orders are treated asStandard Orders and will ship
within24hours.WewillmakeeveryefforttoshipAirShipmentsthesamedaytheorderisreceived,
if received prior to 2PM PST. Stock Orders must be noted on fax or web order form.
NOTE
WE ACCEPT ALL MAJOR CREDIT CARDS!
PAGE 4 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — SPECIFICATIONS
TABLE 1. G55H SPECIFICATIONS
Vibrator Shaft Speed 10,600 RPMs @ 3600 Engine RPMs
Power Unit
Dimensions
(L x W x H)
24 x 20 x 18 in.
(61 x 51 x 46 cm.)
Weight w/ Engine
77 Lbs. (35 Kg)
TABLE 2. ENGINE SPECIFICATIONS
Model
HONDA GX160K1QX2
Type
4-stroke, Overhead valve, Single Cylinder
2.7 in. X 1.8 in.
(68 mm x 45 mm)
Bore X Stroke
Displacement
9.9 cu. in. (163 cc)
5.4 bhp(4.0 kW, 5.5 PS) @ 3,600 R.P.M.
Approx. 0.95 U.S. Gallons (3.6 Liters)
1,400 +200/-150 R.P.M.
Max Output
Engine
Fuel Tank Capacity
Standard Idle Speed
Fuel
Unleaded Gasoline
Lube Oil Capacity
Speed Control Method
Starting Method
0.63 U.S. Quarts (0.60 Liters)
Centrifugal Fly-weight Type
Recoil Start
12.0 x 14.3 X 13.2 in.
(304 X 362 X 335 mm)
Dimension (L x W x H)
Dry Net Weight
33.1 lbs (15.0 Kg.)
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 5
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — SAFETY MESSAGE ALERT SYMBOLS
FORYOUR SAFETY ANDTHE SAFETY OF OTHERS!
HAZARD SYMBOLS
Safety precautions should be followed
at all times when operating this
equipment. Failure to read and
understand the Safety Messages and
Operating Instructions could result in
injury to yourself and others.
Potential hazards associated with the operation of the G-
55H Gasoline Vibrator will be referenced with Hazard
Symbols which appear throughout this manual, and will be
Lethal Exhaust Gases
referenced in conjunction with Safety Message Alert
Symbols.
Lethal Exhaust Gas Hazards
WARNING
This Owner's Manual has been
developed to provide complete
instructions for the safe and efficient
operation of the G-55H Gasoline
Vibrator. Refer to the engine
Engine exhaust gases contain
poisonous carbon monoxide. This gas
is colorless and odorless, and can
cause death if inhaled. NEVER operate
this equipment in a confined area or
enclosed structure that does not provide ample free flow
air.
manufacturers instructions for data relative to its safe
operation.
Before using this vibrator, ensure that the operating
individual has read and understands all instructions in
this manual.
Explosive Fuel Hazards
WARNING
SAFETY MESSAGE ALERT SYMBOLS
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
The three (3) Safety Messages shown below will inform you
about potential hazards that could injure you or others. The
Safety Messages specifically address the level of exposure
to the operator, and are preceded by one of three words:
DANGER, WARNING, or CAUTION.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
DANGER
You WILL be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
Burn Hazards
WARNING
Engine components can generate extreme
heat. To prevent burns, DO NOT touch
these areas while the engine is running or
immediately after operations. Never
operate the engine with heat shields or heat
guards removed.
WARNING
You CAN be KILLED or SERIOUSLY injured if you DO
NOT follow directions.
CAUTION
Respiratory Hazards
WARNING
You CAN be INJURED if you DO NOT follow directions.
ALWAYS wear approved respiratory
protection when required.
PAGE 6 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — SAFETY MESSAGE ALERT SYMBOLS
Equipment Damage
Rotating Parts Hazards
CAUTION
CAUTION
Hazards
NEVER operate equipment with covers,
or guards removed. Keep fingers, hands,
hair and clothing away from all moving
parts to prevent injury.
Other important messages are provided throughout this
manual to help prevent damage to your equipment, other
property, or the surrounding environment.
Accidental Starting Hazards
CAUTION
ALWAYS place the ON/OFF switch in
the OFF position.
Eye and Hearing Hazards
CAUTION
ALWAYS wear approved eye and
hearing protection.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 7
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — RULES FOR SAFE OPERATION
■
NEVER touch the hot exhaust
manifold, muffler or cylinder. Allow
these parts to cool before servicing
engine or vibrator.
Read this manual!
DANGER
Failure to follow instructions in this manual may lead to
serious injury or even death! This equipment is to be
operated by trained and qualified personnel only! This
equipment is for industrial use only.
■
High Temperatures – Allow the
engine to cool before adding fuel or
performing service and maintenance
functions. Contact with hot! components can cause
serious burns.
The following safety guidelines should always be used when
operating the G-55H GasolineVibrator:
GENERAL SAFETY
■
The engine section of this
vibrator requires an adequate
free flow of cooling air.
NEVER operate the vibrator in
any enclosed or narrow area
where free flow of the air is
restricted. If the air flow is
restricted it will cause serious damage to the vibrator or
engine and may cause injury to people. Remember the
vibrator's engine gives off DEADLY carbon monoxide
gas.
■
DO NOT operate or service this
equipment before reading this entire
manual.
■
■
This equipment should not be operated by persons under
18 years of age.
NEVER operate this equipment without proper protective
clothing, shatterproof glasses, steel-toed boots and other
protective devices required by the job.
■
■
ALWAYS refuel in a well-ventilated area, away from
sparks and open flames.
■
■
NEVER operate this equipment when not
feeling well due to fatigue, llness or taking
medicine.
ALWAYS use extreme caution when working with
flammable liquids.When refueling, stop the engine and
allow it to cool. DO NOT smoke around or near the
machine. Fire or explosion could result from fuel vapors,
or if fuel is spilled on a hot engine.
NEVER operate this equipment under the influence
of drugs or alcohol.
■
■
NEVER operate the equipment in an
explosive atmosphere or near
combustible materials. An explosion
or fire could result causing severe
bodily harm or even death.
Topping-off to filler port is dangerous, as it tends to spill
fuel.
■
ALWAYS wear proper respiratory (mask),
hearing and eye protection equipment
when operating the vibrator.
■
■
Stop the engine when leaving the vibrator unattended.
Maintain this equipment in a safe operating condition at
all times.
ALWAYS check to make sure the cutting area is clear
before starting the engine.
ALWAYS clear the work area of any debris, tools, etc.
that would constitute a hazard while the vibrator is in
operation.
■
■
■
Whenever necessary, replace nameplate, operation and
safety decals when they become difficult read.
■
■
Manufacture does not assume responsibility for any
accident due to equipment modifications.
NEVER use accessories or attachments, which are not
recommended by Multiquip for this equipment. Damage
to the equipment and/or injury to user may result.
PAGE 8 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — RULES FOR SAFE OPERATION
TRANSPORTING
■
■
■
■
ALWAYS stop the engine before servicing, adding fuel
and oil.
NEVER run engine without air filter. Severe engine
damage may occur.
ALWAYS service air cleaner frequently to prevent
carburetor malfunction.
ALWAYS be sure the operator is familiar with proper
safety precautions and operations techniques before
using.
ALWAYS store equipment properly when it is not being
used. Equipment should be stored in a clean, dry location
out of the reach of children.
DO NOT operate this equipment unless all guards and
safety devices are attached and in place.
CAUTION must be exercised while servicing this
equipment. Rotating and moving parts can cause injury
if contacted.
■
■
ALWAYS shutdown engine before transporting.
Tighten fuel tank cap securely and close fuel cock to
prevent fuel from spilling.
■
ALWAYS use proper lifting techniques when using or
moving the vibrator motor, flexible shaft or vibrator head
assembly.
MAINTENANCE
■
NEVER lubricate components or attempt service on a
■
running vibrator.
■
ALWAYS allow the vibrator a proper amount of time to
cool before servicing.
■
■
■
■
Keep the vibrator in proper running condition.
Fix damage to the vibrator immediately and always
replace broken parts.
■
■
Dispose of hazardous waste properly. Examples of
potentially hazardous waste are used motor oil, fuel and
fuel filters.
■
■
Keep all inexperienced and unauthorized people away
from the equipment at all times.
Unauthorized equipment modifications will void all
warranties.
DO NOT use food or plastic containers to dispose of
hazardous waste.
EMERGENCIES
■
■
NEVER pour or spray water over the engine.
Test the ON/OFF switch for the gasoline engine before
operating.The purpose of these switches is to shut down
the engine of the vibrator.
■
ALWAYS know the location of the nearest fire
extinguisher and first aid kit.
■
Refer to the HONDA Engine Owner's Manual for engine
technical questions or information recommended by
Multiquip for this equipment. Damage to the equipment
and/or injury to user may result.
■
In emergencies always know the location of
the nearest phone or keep a phone on the
job site. Also know the phone numbers of the
nearest ambulance, doctor and fire
department. This information will be
invaluable in the case of an emergency.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 9
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — OPERATION AND SAFETY DECALS
Operation And Safety Decals
The MQ/STOW G-55H GasolineVibrator is equipped with a number of operation and safety decals (Figure 1).These decals
are provided for operator safety and maintenance information. Should any of these decals become unreadable, replacements
can be obtained from your dealer.
Figure 1. Operation and Safety Decals
PAGE 10 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — GENERAL INFORMATION
General Information
Theory Of ConcreteVibration
The G-55H GasolineVibrator employs a 5.5 HP Honda engine.
It comes standard with a quick-disconnect coupling and an
eccentric belt tensioner.
This G-55H vibrator is designed for the compaction of
concrete by removal of air pockets and voids.
The purpose of vibration is to set the particles in the fresh
concrete in motion, thereby reducing the friction between
the particles and giving the mixture the mobile quality of a
thick fluid so that gravity and the displacement of entrapped
air will cause it to settle easily into place.
The G-55H power unit utilizes a sturdy frame which enables
the engine to operate in a 360° rotation.
When operating the vibrator always wear rubber insulated
gloves and boots. Safety glasses are also recommended.
By consolidating the concrete quickly, "stiffer" or "drier" mixes
can be poured than would otherwise be possible. It has
been proven that (up to a point) the drier the concrete, (that
is, the less water in it), the better the quality throughout and
the greater the strength. Drier mixes also make the concrete
more water tight, increase resistance to weathering, and
create a better bond between concrete and reinforcement.
Tips
■
Keep the bending radius of the flexible hose to a minimum
during use.
■
Avoid starting the unit with the vibrator head immersed in the
concrete mix. After the engine has started, immerse the vibrator
head into concrete mix.
Because vibration causes much of the entrapped air in the
concrete to rise to the surface, honeycombing is prevented.
Also, vibration eliminates most of the air pockets between
the concrete and the vertical forms.
■
■
■
Excessive wear to the vibrating head can result from misuse.
DO NOT allow the head to vibrate against already hardened
concrete or steel used in reinforcement.
NEVER drop or knock the vibrator head against any hard
objects.This will prevent any damage the eccentric or bearings
contain within the head.
ALWAYS rinse or wipe off any wet concrete before it dries or
hardens on any part of the unit
(engine, shaft, or head).
Before operating this gasoline
powered vibrator, the operator
must read and understand the
contents of the operation manual.
Failure to read this manual could
result in severe bodily harm and
damage to the equipment.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 11
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — MAJOR COMPONENTS
Figure 2. G-55H Gasoline Vibrator Components
Figure 2 shows the location of the components and general
maintenance parts. The function of each component is
described below:
1. Eccentric Bell End – Supports the spindle shaft and 5. Rear Belt Guard – Attaches to the V-belt housing and
upper pulley which drives the vibration function of the
G-55H. The flexible shaft and quick disconnect are
inserted into the open end of the Eccentric Bell.
prevents access to the pulleys orV-belts while the vibrator
is running. DO NOT operate the vibrator with this cover
removed.
2. 328V Quick Disconnect – Connect the flexible shaft to 6. V-belt Housing – Encloses the pulley's and v-belts.
the quick disconnect and insert into the eccentric bell.
This allows for rapid removal of the flexible shaft end
from the vibrator base.
Access is provided through openings in the front and
rear of the housing.
7. Vibrator Support Stand – Allows the vibrator base to
sit upright. A pivot mechanism allows the base to freely
pivot in a complete 360 degree circle for operators
convieniance.
3. Quick Disconnect Lock Pin – Pull up on the lock pin
and pull the flexible shaft out to release the quick
disconnect from the eccentric bell. To insert a flexible
shaft, pull up on the lock pin and insert the quick
disconnect fitting. Release the pin and turn the fitting
until the lock pin drops into one of the holes on the fitting
end.
4. Front Belt Guard – Attaches to the V-belt housing and
prevents access to the pulleys orV-belts while the vibrator
is running. DO NOT operate the vibrator with this cover
PAGE 12 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — ENGINE COMPONENTS
5.5 HP Honda Gasoline Engine
The engine (Figure 3) must be checked for proper lubrication
and filled with fuel prior to operation. Refer to the
manufacturer's engine manual for instructions & details of
operation and servicing.The engine shown above is a HONDA
engine. Operation for other types of engines may vary.
1. Fuel Filler Cap – Remove this cap to add unleaded
gasoline to the fuel tank. Make sure cap is tightened
securely. DO NOT over fill.
Explosive
Fuel Hazard
DANGER
Adding fuel to the tank should be done only when the
engine is stopped and has had an opportunity to cool
down. In the event of a fuel spill,
DO NOT attempt to start the engine until
the fuel residue has been completely
wiped up, and the area surrounding the
engine is dry.
2. Throttle Lever – Used to adjust engine RPM speed
(lever advanced forward SLOW, lever back toward
operator FAST).
3. Engine ON/OFF Switch – ON position permits engine
starting, OFF position stops engine operation.
4. Recoil Starter (pull rope) – Manual-starting method.
Pull the starter grip until resistance is felt, then pull
briskly and smoothly.
Figure 3. Honda GX160T1QX2 Engine Components
9. Muffler – Used to reduce noise and emissions.
5. Fuel Valve Lever – OPEN to let fuel flow, CLOSE to
stop the flow of fuel.
Burn Hazard
WARNING
6. Choke Lever – Used in the starting of a cold engine, or
in cold weather conditions.The choke enriches the fuel
mixture.
Engine components can generate
extreme heat. To prevent burns, DO
NOT touch these areas while the engine
is running or immediately after
operating. NEVER operate the engine
with the muffler removed.
7. Air Cleaner – Prevents dirt and other debris from entering
the fuel system. Remove wing-nut on top of air filter
cannister to gain access to filter element.
Operating the engine without an air
10. Fuel Tank – Holds unleaded gasoline. For additional
filter, with a damaged air filter, or a
filter in need of replacement will
allow dirt to enter the engine,
causing rapid engine wear.
NOTE
information refer to engine owner's manual.
11. Oil Drain Plug – Remove this plug to remove oil from
the engine's crankcase.
12. Dipstick/Oil Filler Cap – Remove this cap to determine
if the engine oil is low. Add oil through this filler port as
recommended in Table 3.
8. Spark Plug – Provides spark to the ignition system.
Clean spark plug once a week.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 13
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — INSPECTION
Inspection &
Maintenance Saftey
CAUTION
NEVER place hands or feet inside the belt
guard cover while the engine is running.
ALWAYS shut the engine down before
performing any kind of maintenance
service on the unit.
Eyesight and Hearing
Protection
Figure 4. Engine Oil Dipstick (Removal)
CAUTION
3. Insert and remove the dipstick without screwing it into
the filler neck. Check the oil level shown on the dipstick.
ALWAYS wear approved eye and
hearing protection before inspecting,
operating or servicing the vibrator.
4. If the oil level is low (Figure 5), fill to the edge of the oil
filler hole with the recommended oil type (Table 3).
Maximum oil capacity is 0.63 quarts (.60 liters).
Before Starting
Before starting and operating the G-55H Gasoline Vibrator,
perform the following:
Reference manufacturer engine
manual for specific servicing
■
■
Read safety instructions at the beginning of manual.
instructions.
Clean the vibrator, removing dirt and dust, particularly
the engine cooling air inlet, carburetor and air cleaner.
UPPER LIMIT
■
■
Check the air filter for dirt and dust. If air filter is dirty,
replace air filter with a new one as required.
Check carburetor for external dirt and dust. Clean with
dry compressed air.
■
■
■
■
Check fastening nuts and bolts for tightness.
Check the engine oil level of the engine.
Check the fuel level of the engine.
LOWER LIMIT
Figure 5. Engine Oil Dipstick (Oil Level)
Check the tension and condition of the vibrator power
unit's V-belts.
Table 3. Oil Type
Engine Oil Check
Season
Summer
Spring/Fall
Winter
Temperature
25°C or Higher
25°C~10°C
Oil Type
SAE 10W-30
SAE 10W-30/20
SAE 10W-10
1. To check the engine oil level, place the vibrator on
secure level ground with the engine stopped.
2. Remove the filler dipstick from the engine oil filler hole
(Figure 4) and wipe clean.
0°C or Lower
PAGE 14 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — INSPECTION
V-Belt Check
Explosive Fuel Hazards
WARNING
A worn or damaged V-belt can adversely affect the
performance of the vibrator.
Gasoline is extremely flammable, and
its vapors can cause an explosion if
ignited. DO NOT start the engine near
spilled fuel or combustible fluids.
1. Unscrew the bolts securing the front belt guard to the
belt housing
2. Inspect the belts for defects or wear.
DO NOT fill the fuel tank while the engine is running or
hot. DO NOT overfill tank, since spilled fuel could ignite if
it comes into contact with hot engine parts or sparks from
the ignition system. Store fuel in approved containers, in
well-ventilated areas and away from sparks and flames.
3. If a V-belt is defective or worn, replace the V-belt as
outlined in the maintenance section of this manual.
Moving the Vibrator
Even though the vibrator is lightweight, always use two
people when lifting the vibrator or moving the unit around the
jobsite.
1. Remove the gasoline cap located on top of fuel tank.
2. Visually inspect to see if fuel level is low. If fuel is low,
replenish with unleaded fuel.
3. Whenrefueling,besuretouseastrainerforfiltration.DO
NOT top-off fuel. Wipe up any spilled fuel.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 15
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — START-UP PROCEDURES
3. Placetheenginechokelever (Figure8)intheCLOSED
position if starting a cold engine.Place the choke lever
in the OPEN position if starting a warm engine or the
temperature is warm.
This section is intended to assist the operator
with initial start-up. It is extremely important
that this section be read carefully before
attempting to use the vibrator in the field.
DO NOT use your vibrator until this section is thoroughly
understood.
General Safety
WARNING
Failure to understand the operation of this vibrator could
result in severe damage to the vibrator or personal injury.
See Figures 2 and 3 for the location of any control
referenced in this manual.
Respiratory Hazard
Figure 8. Engine Choke Lever
CAUTION
5. Place the engine ON/OFF switch (Figure 9) in the ON
position.
NEVER operate the vibrator in a
confined area or enclosed area structure
that does not provide ample free flow
of air.
Starting the Engine
1. Place the engine fuel valve lever (Figure 6) to the ON
position
Figure 9. Engine ON/OFF Switch
6. Grasp the recoil starter grip (Figure 10) and slowly pull
it out. The resistance becomes the hardest at a certain
position, corresponding to the compression point. Pull
the starter grip briskly and smoothly for starting.
Figure 6. Engine Fuel Valve Lever
2. Place the engine throttle lever (Figure 7) to the IDLE or
SLOW position.
Figure 10. Starter Grip
Figure 7. Throttle Lever
PAGE 16 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — START-UP/SHUTDOWN PROCEDURES
7. If the engine has started, slowly return the choke lever Stopping The Engine
(Figure 6) to the OPEN position. If the engine has not
started repeat steps 1 through 6.
1. Move the throttle lever to the IDLE or SLOW position
(Figure 11) and run the engine for three minutes at low
8. Before the vibrator is placed into operation, immerse the
vibrator head into the concrete and run the engine for
several minutes. Check for fuel leaks, and noises that
would associate with a looseV-belt cover or component.
speed.
2. Aftertheenginecools,turntheenginestart/stopswitch
to the OFF position (Figure 11).
Vibrator Head
Overheating Hazard
CAUTION
The vibrator head is cooled by the concrete. Operation
of the vibrator head in air longer than 2 minutes will
cause overheating of the bearings which result in
premature head failure.
9. Tobeginuse,movethethrottlelever(Figure6)towardthe
Figure 11. Engine ON/OFF Switch (OFF Position)
FAST position.
3. Closethefuelshut-offvalve (Figure12)bymovingthe
fuel valve lever to the OFF position.
Figure 12. Fuel Valve Lever (OFF Position)
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 17
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — OPERATION
Connecting the 382V Flexible Shaft
Operation
1. Connect the 382V Flexible Shaft to the Quick Disconnect
coupling (Figure 13).
Read all the safety instructions carefully. Safety instructions
will be found throughout this manual and on the vibrator motor.
Keep all safety information available, accessible, and in good,
readable condition.
2. Pull UP on the lock pin and slide the shaft and quick
disconnect assembly into the eccentric end bell and
release the lock pin.
■
Make certain that the flexible shaft is properly attached
to the motor and the head to the flexible shaft.
3. Twist the shaft assembly to make sure that the lock pin
is seated in one of the 3 tapered holes on the quick
disconnect coupling.
■
■
Use the flexible shaft in as straight a position as possible.
Do not bend the flexible shaft sharply at any point.
Sharp bends may cause a permanent kink, requiring
early replacement of the flexible shaft.
Equipment Combination Information
The following Equipment Combination Chart shows all of
the recommended connections between the gasoline vibrator
and the vibrator head.
TABLE 5. EQUIPMENT COMBINATIONS
MAX SHAFT
Figure 13. Couplings
COUPLING
SHAFT
HEAD
LENGTH
Connecting the vibrator head to the flexible shaft
1400 vib.
1700 vib.
2100 vib.
1. Clean the mating parts threads with Loctite Primer “T”.
28 ft. (132.3 cm)
21 ft. (99.2 cm)
382V Q.D
382V
2. Allow to dry several minutes before applying a ring of
Loctite No.271 to the middle of the casing threads.
3. Screw the head tightly to the flexible shaft casing and
wait for 1 hour before using. The threads are left hand,
turn counter-clockwise to tighten. An equivalent brand
of anaerobic sealant may be used.
Equipment Hazard
WARNING
Using head attachments not listed above may create a
hazardous condition when using the vibrator.
The G-55H Gasoline Vibrator, flexible shafting, and head
are shipped from the factory ready for assembly. Follow the
instructions listed below when connecting these parts before
using the gasoline vibrator.
PAGE 18 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — OPERATION
Use the flexible shaft in as straight a position as possible
and do not bend the flexible shaft sharply at any point. Sharp
bends may cause a permanent kink, requiring early
replacement of the flexible shaft.
1. Start the engine as previously described and procede to
insert the vibrator head into the concrete.
2. The concrete is normally placed into the forms in layers
about 12 to 18 inches thick in a manner which forms a
fairly level surface. The vibrator head is inserted
vertically into the top of the pile.
Shaft Overload Hazard
CAUTION
3. When the surface has become fairly level, the vibrator
head then should be immersed and generally moved in
the pattern shown in (Figure 14).
If the shaft begins to helix (buckle) excessively during
operation, stop and investigate.This is an indication of an
overload condition.
Vibrator Head
Overheating Hazard
CAUTION
The vibrator head is cooled by the concrete. Operation
of the vibrator head in air longer than 2 minutes will
cause overheating of the bearings which result in
premature head failure.
Figure 14. Compaction Coverage
with 50% Radial Overlap
TABLE 4. HEAD AND P-DIMENSIONS
1400
1700
2100
HEAD
8 in.
12 in.
14 in.
P-DIMENSION
(31.4 mm) (47.2 mm.) (55.1 mm)
■
Immerse the head for 5 to 10 seconds, (until air stops
rising), and then withdraw it slowly to let the concrete fill
the void left by the vibrator head.
■
■
The vibrator head should be completely below the surface
when vibrating to keep the head cool.
When vibrating a thin horizontal slab, the vibrator head
can be used in a horizontal position.
DO NOT insert the vibrator head
into the side of the pile to make
the concrete flow as this practice
can cause segregation of the
aggregate from the mortar.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 19
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — MAINTENANCE
Maintenance Instructions
■
Remove and clean the spark plug (Figure 24), then adjust
the spark gap to 0.024 ~0.028 inch (0.6~0.7 mm). This
unit has electronic ignition, which requires no
adjustments.
To receive trouble-free service from your G-55H gasoline
vibrator, follow these instructions, as well as the instructions
contained in the engine operating manual, flexible shaft
operations manual and the vibrator head operations manual.
The 382V flexible shafting requires cleaning and lubrication
every 100 hours of operation. Refer to the flexible shaft
operation and parts manual for maintenance instructions.
Vibrator heads should be inspected and relubricated every
100 hours of operation.Refer to the vibrator head operation
and parts manual for maintenance instructions.
Figure 15. Spark Plug Gap
Engine Oil
Heat should be used to break down
the loctite while you unthread the
1. Drain the engine oil when the oil is warm as shown in
NOTE
head from the shaft. This will
prevent possible damage to the
threads from the loctite.
Figure 25.
2. Remove the oil drain bolt and sealing washer and allow
the oil to drain into a suitable container.
3. Replace engine oil with recommended type oil as listed
in Table 3. For engine oil capacity, see Table 2 (engine
specifications). DO NOT overfill.
Disabling the Engine
WARNING
for Maintenance
Whenever assembling, lubricating, or adjusting any part
of the gasoline vibrator make certain to stop the engine,
disconnect the spark plug wire and secure it away from
the spark plug.
4. Installdrainboltwithsealingwasherandtightensecurely.
Daily
■
Thoroughly remove dirt and oil from the engine and
control area. Clean or replace the air cleaner elements
as necessary. Check and retighten all fasteners as
necessary. Check the gearbox for oil leaks. Repair or
replace as needed.
Figure 16. Engine Oil (Draining)
Weekly
Dispose of used oil properly. DO
■
Remove the fuel filter cap and clean the inside of the
NOTE
NOT pour used oil on the ground,
down a drain, or throw in the
trash.
fuel tank.
■
Remove or clean the filter at the bottom of the tank.
Used oil can generally be taken to your local recycling center
or service station for reclamation. Follow all required
environmental rules and regulations required in your area
concerning the disposal of hazardous waste such as used
oil and oil filters.
PAGE 20 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — MAINTENANCE
Engine Air Cleaner
V-BeltTension
1. Remove the air cleaner cover and foam filter element as
shown in Figure 26.
The belt can be tightened by rotating the eccentric
countershaft assembly clockwise. When the belts are
properly tensioned, they should deflect approximately 5 to
10mm when 5-10 pounds of force is applied centrally between
the pulleys. Lock the countershaft in place with the locking
screw and wing nut.
2. Tap the paper filter element (Figure 26) several times on
a hard surface to remove dirt, or blow compressed air
[notexceeding30psi(207kPa, 2.1kgf/cm2)]throughthe
filter element from the air cleaner case side. NEVER
brush off dirt. Brushing will force dirt into the fibers.
Replace the paper filter element if it is excessively dirty.
3. Clean foam element in warm, soapy water or nonflam-
mablesolvent.Rinseanddrythoroughly. Diptheelement
in clean engine oil and completely squeeze out the
excess oil from the element before installing.
Explosive Hazard
DANGER
Figure 18.V-BeltTension
DO NOT use gasoline as a cleaning solvent to avoid
creating the risk of fire or an explosion.
Lubrication
Quick Disconnect Lock
A small amount of any lightweight oil should be used on the
locking mechanism to help keep concrete from sticking and
also to lubricate the locking pin and spring.
Figure 19. Quick Disconnect Lock
Pivot Assembly
Figure 17. Engine Air Cleaner
Grease with a pressure gun as required.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 21
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR —TROUBLESHOOTING (ENGINE)
TABLE 5. TROUBLESHOOTING (ENGINE)
SYMPTOM
POSSIBLE CAUSE
SOLUTION
Check gap, insulation or
replace spark plug.
Spark plug bridging?
Carbon deposit on spark plug?
Clean or replace spark plug.
Difficult to start, "fuel is available, but no
SPARK at spark plug".
Short circuit due to deficient spark plug
insulation?
Check spark plug insulation,
replace if worn.
Improper spark plug gap?
Ignition coil defective?
Set to proper gap.
Replace ignition coil.
Check switch wiring, replace
switch.
ON/OFF switch is shorted?
Set correct spark gap and
clean points.
Improper spark gap, points dirty?
Difficult to start, "fuel is available, and
SPARK is present at the spark plug".
Condenser insulation worn or short
circuiting?
Replace condenser.
Replace defective spark plug
wiring.
Spark plug wire broken or short circuiting?
Wrong fuel type?
Flush fuel system, and replace
with correct type of fuel.
Water or dust in fuel system?
Air cleaner dirty?
Flush fuel system.
Replace air cleaner.
Close Choke.
Difficult to start, "fuel is available, spark
is present and compression is normal".
Choke Open?
Suction/exhaust valve stuck or protruded?
Re-seat valves.
Replace piston rings and/or
piston.
Piston ring and/or cylinder worn?
Difficult to start, "fuel is available, spark
is present and compression is low".
Cylinder head and/or spark plug not
tightened properly?
Torque cylinder head bolts and
spark plug.
Head gasket and/or spark plug gasket
damaged?
Replace head and/or spark plug
gaskets.
Fuel not available in fuel tank (tank empy)? Fill with correct type of fuel.
Fuel filter clogged?
Replace fuel filter.
No fuel present at the carburetor.
Fuel tank cap breather hole clogged?
Air in fuel line?
Clean or replace fuel tank cap.
Bleed fuel line.
PAGE 22 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 23
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H VIBRATOR — EXPLANATION OF CODE IN REMARKS COLUMN
The following section explains the different symbols and remarks QTY. Column
used in the Parts section of this manual. Use the help numbers
found on the back page of the manual if there are any questions.
Numbers Used - Item quantity can be indicated by a number,
a blank entry, or A/R.
A/R (As Required) is generally used for hoses or other parts
that are sold in bulk and cut to length.
The contents and part numbers listed in the parts section are
A blank entry generally indicates that the item is not sold
separately. Other entries will be clarified in the “Remarks”
Column.
subject to change without notice. Multiquip does not
guarantee the availibility of the parts listed.
Sample Parts List:
REMARKS Column
NO. PART NO. PART NAME
QTY. REMARKS
Some of the most common notes found in the “Remarks”
Column are listed below. Other additional notes needed to
describe the item can also be shown.
1
2
2
3
4
12345
BOLT ....................... 1.... INCLUDES ITEMS W/
WASHER, 1/4 IN. ........... NOT SOLD SEPARATELY
WASHER, 3/8 IN. .... 1.... MQ-45TONLY
HOSE .................... A/R.. MAKE LOCALLY
BEARING ................ 1.... S/N2345B AND ABOVE
*
*
*
12347
12348
12349
Assembly/Kit - All items on the parts list with the same unique
symbol will be included when this item is purchased.
Indicated by:
“INCLUDES ITEMS W/(unique symbol)”
NO. Column
Unique Symbols - All items with same unique symbol
Serial Number Break - Used to list an effective serial number
range where a particular part is used.
( , #,
+
, %, or >) in the number column belong to the same
*
assembly or kit, which is indicated by a note in the “Remarks”
column.
Indicated by:
“S/N XXXXX AND BELOW”
“S/N XXXX AND ABOVE”
“S/N XXXX TO S/N XXX”
Duplicate Item Numbers - Duplicate numbers indicate
multiple part numbers are in effect for the same general item,
such as different size saw blade guards in use or a part that
has been updated on newer versions of the same machine.
Specific Model Number Use - Indicates that the part is used
only with the specific model number or model number variant
listed. It can also be used to show a part is NOT used on a
specific model or model number variant.
When ordering a part that has more
than one item number listed, check
the remarks column for help in
determining the proper part to order.
NOTE
Indicated by:
“XXXXX ONLY”
“NOT USED ON XXXX”
“Make/Obtain Locally” - Indicates that the part can be
purchased at any hardware shop or made out of available
items. Examples include battery cables, shims, and certain
washers and nuts.
PART NO. Column
Numbers Used - Part numbers can be indicated by a number,
a blank entry, orTBD.
TBD (To Be Determined) is generally used to show a part that
has not been assigned a formal part number at time of
publication.
“Not Sold Separately” - Indicates that an item cannot be
purchased as a separate item and is either part of an
assembly/kit that can be purchased, or is not available for
sale through Multiquip.
A blank entry generally indicates that the item is not sold
separately or is not sold by Multiquip. Other entries will be
clarified in the “Remarks” Column.
PAGE 24 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — SPARE PARTS
G-55H GASOLINEVIBRATOR
1TO 3 UNITSW/HONDA GX160K1QX2
ENGINE
Qty.
P/N
Description
3 ............ 9807956846 .......... SPARK PLUG
3 ............ 17210ZE2505 ....... ELEMENT, AIR CLEANER
1 ............ 28462ZE2W11 ...... ROPE STARTER
1 ............ 17620ZH7023 ....... CAP, W/GASKET FUEL FILLER
4 ............ 16052 .................... V-BELT 3VX335
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 25
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS.
PAGE 26 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — NAMEPLATE AND DECALS
NAMEPLATE AND DECALS.
NO.
1
2
PART NO.
36521
11247
PART NAME
DECAL, G-55H
1
1
DECAL, HELMET, BOOT, GLOVES (ISO BLACK)
3
4
5
11246
11246
DECAL, LIFT POINT................................................. 2 ............ PART OF DECAL KIT 11246
DECAL, HOT SURFACE ........................................... 1 ............ PART OF DECAL KIT 11246
NAMEPLATE............................................................. 1 ............ CONTACT MQ PARTS DEPT.
6
7
21665
25883-001
DECAL, WARNING, KEEP GUARDS IN PLACE
DECAL, CAUTION, READ MANUAL
2
1
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 27
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — ECCENTRIC/BODY ASSY.
ECCENTRIC/BODY ASSY.
PAGE 28 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — ECCENTRIC/BODY ASSY.
ECCENTRIC/BODY ASSY.
NO
PART NO
PART NAME
QTY.
REMARK
1
2
36248
COUPLING, SHAFT
1
18045-501
25015-501
08752-275
06330-002
14043-017
14546-001
08601-045
08751-156
06467-062
584013
2037
20875
22538-001
25845-001
18024-001
0202
ECCENTRIC ASSY. ............................................. 1............... INCLUDES ITEMS W/#
LOCK ASSEMBLY
SNAP RING
BEARING SPRING
BEARING
SPINDLE
SPACER, SPLIT
SNAP RING
SPACER
KEY 3/16" x 3/16" x 1"
LOCKWASHER 5/16
CAP SCREW 5/16" -18 x 3/4
SCREW - THREAD FORMING
BELT GUARD (FRONT)
HOUSING
SCREW, HHC 5/16"-18 x 1
NUT, HEX JAM 5/16"-18
QD BUSHING
PULLEY (UPPER)
PULLEY (LOWER)
BELT 3VX335
KEY - 3/16 SQ. x 1-1/4
BELT GUARD (REAR)
CAP, DUST
3#
4#
5#
6#
7#
8#
9#
10#
11#
12#
13#
14
15
16
17
18
19
20#
21
22
23
24
25#
26
27
1
2
1
2
1
1
1
1
1
1
1
8
1
1
1
1
1
1
1
2
1
1
1
1
1
0106
36517
18044-001
36516
16052
0627
25846-001
11534-018
27100-351
1386
FRAME ASSEMBLY
ENGINE - 5.5 HP HONDA
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 29
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — PIVOT ASSY.
PIVOT ASSY.
PAGE 30 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
G-55H GASOLINEVIBRATOR — PIVOT ASSY.
PIVOT ASSY.
NO
PART NO
PART NAME
QTY.
REMARK
1
2
3
4
5
6
7
5283
NUT - GRIPCO 5/16 - 18
FLATWASHER 5/16
4
4
4
1
1
2
1
0300 B
0105
HHCS 5/16 - 18 x 1 1/2
ENGINE PLATE - PIVOT
GREASE FITTING
27108-351
2621
3264
FLATWASHER 1"
COTTER PIN 5/32" x 1-1/2
07028-057
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 31
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
PAGE 32 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — AIR CLEANER ASSY.
AIR CLEANER ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
QTY.
REMARKS
16271ZE1000
17210ZE1505
17218ZE1821
17230ZE1820
17232891000
17238ZE7010
17239ZE1000
17410ZE1020
90201415000
90325044000
90325044000
957010602000
GASKET, ELBOW
1
1
1
1
1
2
1
1
2
1
1
1
ELEMENT, AIR CLEANER (DUAL)
FILTER, OUTER
COVER, AIR CLEANER (DUAL)
GROMMET, AIR CLEANER
COLLAR, AIR CLEANER
COLLAR B, AIR CLEANER
ELBOW, AIR CLEANER
NUT, CAP 6MM
WINGNUT, TOOL BOX SETTING
WINGNUT, TOOL BOX SETTING
BOLT, FLANGE 6 X 20
9
11
12
13
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 33
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
PAGE 34 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CAMSHAFT ASSY.
CAMSHAFT ASSY.
NO.
1
2
3
4
5
6
7
8
PART NO.
PART NAME
CAMSHAFT ASSEMBLY
ROD, PUSH
ARM, VALVE ROCKER
LIFTER, VALVE
PIVOT, ROCKER ARM
SPRING, WEIGHT RETURN
VALVE, INTAKE
VALVE, EXHAUST
SPRING VALVE
RETAINER, INTAKE VALVE SPRING
RETAINER, EXHAUST VALVE SPRING
ROTATOR,VALVE
PLATE, PUSH ROD GUIDE
BOLT, PIVOT 8MM
QTY.
1
2
2
2
2
1
1
1
2
1
1
1
1
2
2
REMARKS
14100ZE1812
14410ZE1010
14431ZE1000
14441ZE1010
14451ZE1013
14568ZE1000
14711ZF1000
14721ZF1000
14751ZF1000
14771ZE1000
14773ZE1000
14781ZE1000
14791ZE1010
90012ZE0010
90206ZE1000
9
10
11
12
13
14
15
NUT, PIVOT ADJ.
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 35
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
PAGE 36 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CARBURETOR ASSY.
CARBURETOR ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
2
3
4
5
#
+
%
16010ZE1812
16011ZE0005
16013ZE0005
16015ZE0831
16016ZH7W01
16024ZE1811
16028ZE0005
16044ZE0005
16100ZH8W51
16124ZE0005
16166ZH8W50
16173001004
16211ZE1000
16212ZH8800
16220ZE1020
16221ZH8801
16610ZE1000
16953ZE1812
16954ZE1812
16956ZE1811
16957ZE1812
16967ZE0811
93500030060H
9430520122
GASKET SET
VALVE SET, FLOAT
FLOAT SET
1
1
1
*
*
CHAMBER SET, FLOAT............................... 1 ........... INCLUDES ITEMS/
SCREW SET
SCREW SET, DRAIN ................................... 1 ........... INCLUDES ITEM W/+
SCREW SET B ............................................ 1 ........... INCLUDES ITEM W/
CHOKE SET
CARBURETOR ASSEMBLY, BE65B B ........ 1 ........... INCLUDES ITEMS/
SCREW, THROTTLE STOP
NOZZLE, MAIN
O- RING
INSULATOR, CARBURETOR
GASKET, INSULATOR
SPACER, CARBURETOR
GASKET, CARBURETOR
LEVER, CHOKE STANDARD ....................... 1............ INCLUDES ITEM W/$
LEVER, VALVE
PLATE, LEVER SETTING
SPRING, VALVE LEVER
GASKET, VALVE
CUP, FUEL STRAINER
SCREW, PAN 3 X 6
PIN, SPRING 2 X 12
JET, MAIN #65 (OPTIONAL)
JET, MAIN #68 (OPTIONAL)
JET SET, PILOT #35
#
*
1
*
6
7
8
#
*
%
*
1
*
9
*
10
11
12
13
14
15
16
17
18
19
20
21
22
23
1
1
1
1
1
1
1
*
*
*
1
1
1
1
1
2
1
1
1
1
*
*
*
*
*
24$
25
99101ZH80650
99101ZH80680
99204ZE00350
*
25
*
26
*
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 37
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
PAGE 38 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CONTROL ASSY.
CONTROL ASSY.
NO.
2
4
5
6
PART NO.
PART NAME
QTY.
REMARKS
16500ZH8823
16551ZE0010
16555ZE1000
16561ZE1020
16562ZE1020
16571ZH8020
16574ZE1000
16575ZH8000
16576891000
16578ZE1000
16580ZH8812
16584883300
16592ZE1810
90013883000
90016ZE5010
90114SA0000
93500050250H
938930501600
9405006000
CONTROL ASSEMBLY, REMOTE......................... 1............ INCLUDES ITEMS W/
*
ARM, GOVERNOR
ROD, GOVERNOR
SPRING GOVERNOR
SPRING,THROTTLE RETURN
LEVER, CONTROL
SPRING, LEVR
WASHER, CONTROL LEVER
HOLDER, CABLE
SPACER, CONTROL LEVER
BASE, CONTROL (REMOTE)
SPRING, CONTROL ADJUSTING
SPRING, CABLE RETURN
BOLT, FLANGE 6 X 12 (CT200)
BOLT, GOVERNOR ARM
NUT, SELF- LOCK 6MM
SCREW, PAN 5 X 25
1
1
1
1
1
1
1
1
1
1
1
1
2
1
1
1
1
1
7
8
9
*
*
10
*
11
*
12
*
13
*
14
*
15
*
17
18
19
*
22
*
23
*
SCREW, WASHER 5 X 16
NUT, FLANGE 6MM
24
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 39
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
PAGE 40 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CRANKCASE COVER ASSY.
CRANKCASE COVER ASSY.
NO.
1
3
4
5
9
10
PART NO.
PART NAME
QTY.
REMARKS
11300ZE1641
11381ZH8801
15600ZE1003
15600ZG4003
15625ZE1003
15625ZE1003
91202883005
9430108140
COVER ASSEMBLY, CRANKCASE (U- TYPE) ..... 1 ........... INCLUDES ITEMS W/
*
GASKET, CASE COVER (NON- ASBESTOS)
CAP ASSEMBLY, OIL FILLER
CAP ASSEMBLY, OIL FILLER
GASKET, OIL FILLER CAP
GASKET, OIL FILLER CAP
OIL SEAL 25 X 41 X 6
PIN A, DOWEL 8 X 14
BOLT, FLANGE 8 X 32
BEARING, RADIAL BALL 6205
1
1
1
1
1
1
2
6
1
11
12
13
*
957010803200
961006205000
14
*
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 41
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CRANKSHAFT/BALANCER ASSY.
CRANKSHAFT /BALANCER WEIGHT ASSY.
PAGE 42 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CRANKSHAFT/BALANCER ASSY.
CRANKSHAFT ASSY.
NO.
3
9
PART NO.
13310ZE1601
90745ZE1600
PART NAME
CRANKSHAFT, Q- TYPE
KEY, 4.78 X 4,78 X 38
QTY.
1
1
REMARKS
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 43
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
PAGE 44 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CYLINDER BARREL ASSY.
CYLINDER BARREL ASSY.
NO.
2
3
PART NO.
PART NAME
QTY.
REMARKS
12000ZH8811
15510ZE1033
16510ZE1000
16511ZE1000
16512ZE1000
16531ZE1000
16541ZE1000
90131ZE1000
80451ZE1000
90601ZE1000
90602ZE1000
91001ZF1003
91202883005
91353671003
9405010000
CYLINDER ASSEMBLY, OIL ALERT .................... 1............ INCLUDES ITEMS W/
SWITCH ASSEMBLY, OIL LEVEL......................... 1 ........... INCLUDES ITEMS W/
GOVERNOR ASSEMBLY ...................................... 1............ INCLUDES ITEMS W/
*
%
#
4
*
5
6
8
#
#
WEIGHT, GOVERNOR
HOLDER, GOVERNOR WEIGHT
SLIDER, GOVERNOR
SHAFT, GOVERNOR ARM
BOLT, DRAIN PLUG
WASHER, THRUST 6MM
WASHER, DRAIN PLUG 10.2MM
CLIP, GOVERNOR HOLDER
BEARING, RADIAL BALL 6205
OIL SEAL 25 X 41 X 6
O- RING 13.5 X 1.5 (ARAI)
NUT, FLANGE 10MM
WASHER, PLAIN 6MM
PIN, LOCK 8MM
2
1
1
1
2
1
2
1
1
1
1
1
2
1
2
*
*
*
9
10
11
12
13
14
15
16
17
18
19
20
*
*
%
%
9410106800
9425108000
957010601200
*
BOLT, FLANGE 6 X 12
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 45
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
PAGE 46 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — CYLINDER HEAD ASSY.
CYLINDER HEAD ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
12210ZH8000
12204ZE1306
12205ZE1315
12216ZE5300
12251ZF1800
12310ZE1010
12391ZE1000
15721ZH8000
90016ZE1000
90043ZE1020
90047ZE1000
9430110160
CYLINDER HEAD.................................................. 1............ INCLUDES ITEMS W/
*
2
*
3
*
GUIDE, VALVE OS (OPTIONAL
GUIDE, EXHAUST VALVE OS (OPTIONAL) ......... 1............ INCLUDES ITEM W/
CLIP, VALVE GUIDE
GASKET, CYLINDER HEAD
COVER, HEAD
GASKET, CYLINDER HEAD COVER
TUBE, BREATHER
BOLT, FLANGE 6 X13
BOLT, STUD 6 X109
1
%
4
%
1
1
1
1
1
4
2
2
2
4
1
5
6
7
8
9
10
11
12
14
15
BOLT, STUD 8 X 32
PIN A, DOWEL 10 X16
BOLT, FLANGE 8 X60
SPARK PLUG BPR6ES (NGK)
957230806000
9807956846
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 47
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
PAGE 48 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — FAN COVER ASSY.
FAN COVER ASSY.
NO.
2
4
7
8
10
11
13
14
17
19
PART NO.
PART NAME
QTY.
REMARKS
19610ZE1000ZC
19611ZH8810
90601ZH7013
19630ZH8000
32197ZH8003
36100ZE1015
90013883000
90022888010
34150ZH7003
957010600800
COVER, FAN "NH1" (BLACK)
PLATE, SIDE (OIL ALERT)
CLIP, HARNESS
1
1
1
1
1
1
6
1
1
1
SHROUD
SUB- HARNESS
SWITCH ASSEMBLY, ENGINE STOP
BOLT, FLANGE 6 X12 (CT200)
BOLT, FLANGE 6 X20 (CT200)
ALERT UNIT, OIL
BOLT, FLANGE 6 X8
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 49
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
PAGE 50 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — FLYWHEEL ASSY.
FLYWHEEL ASSY.
NO.
1
2
4
5
5
8
PART NO.
PART NAME
KEY, SPECIAL WOODRUFF (25 X18)
FAN, COOLING
PULLEY, STARTER
FLYWHEEL
FLYWHEEL, LAMP
NUT, SPECIAL 14MM
QTY.
REMARKS
13331357000
19511ZE1000
28451ZH8003
31100ZE1010
31100ZE1810
90201878003
1
1
1
1
1
1
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 51
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
PAGE 52 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — FUELTANK ASSY.
FUEL TANK ASSY.
NO.
1
2
3
3
PART NO.
PART NAME
RUBBER, SUPPORTER 107MM
JOINT, FUEL TANK
TANK, FUEL *R8* (BRIGHT RED)
TANK, FUEL *NH1* (BLACK)
CAP, FUEL FILLER ............................................... 1 ........... INCLUDES ITEM W/
GASKET, FUEL FILLER CAP
O- RING 13.5 X1.5 (ARAI)
NUT, FLANGE 6MM
BULK HOSE, FUEL 4.5 X 3000 (4.5 X 140)
CLIP, TUBE B8
QTY.
REMARKS
16854ZH8000
16955ZE1000
17510ZE1020ZB
17510ZE1020ZF
17620ZH7023
17631ZH7003
91353671003
9405006000
1
1
1
1
5
6
*
1
1
2
1
2
1
*
11
12
13
14
15
950014500360M
9500202080
957010602500
BOLT, FLANGE 6 X 25
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 53
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
PAGE 54 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — IGNITION COIL ASSY.
IGNITION COIL ASSY.
NO.
1
2
7
11
PART NO.
PART NAME
QTY.
REMARKS
30500ZE1033
30700ZE1013
36101ZE1010
90121952000
COIL ASSEMBLY, IGNITION
CAP ASSEMBLY, NOISE SUPPRESSOR
WIRE, STOP SWITCH 370MM
BOLT, FLANGE 6 X25
1
1
1
2
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 55
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
PAGE 56 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — MUFFLER ASSY.
MUFFLER ASSY.
NO.
1
1
3
7
PART NO.
PART NAME
QTY.
REMARKS
18310ZF1000
18310ZH8810
18320ZF1H01
18355ZE1000
18381ZH8800
90050ZE1000
90055ZE1000
94001080000S
MUFFLER
1
1
1
1
1
4
1
2
MUFFLER (OPTIONAL)
PROTECTOR, MUFFLER
ARRESTER, SPARK (OPTIONAL)
GASKET, MUFFLER
SCREW, TAPPING 5 X 8 (OPTIONAL
SCREW, TAPPING 4 X 6 (OPTIONAL)
NUT, HEX. 8MM
8
11
12
15
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 57
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — PISTON ASSY.
PISTON ASSY.
PAGE 58 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — PISTON ASSY.
PISTON ASSY.
NO.
1
1
1
1
2
2
2
2
3
4
4
5
PART NO.
PART NAME
QTY.
REMARKS
13010ZH8941
13011ZH8941
13012ZH8941
13013ZH8941
13101ZH8000
13102ZH8000
13103ZH8000
13104ZH8000
13111ZE1000
132AOZE1000
13200ZE1010
90001ZE1000
90551ZE1000
RING SET, PISTON (STANDARD)
RING SET, PISTON (OS 0.25), OPTIONAL
RING SET, PISTON (OS 0.50), OPTIONAL
RING SET, PISTON (0.75), OPTIONAL
PISTON (STANDARD)
1
1
1
1
1
1
1
1
1
1
1
2
2
PISTON (OS 0.25), OPTIONAL
PISTON (OS 0.50), OPTIONAL
PISTON (0.75), OPTIONAL
PIN, PISTON
ROD ASSY., CONNECTING (US 0.25), OPT.
ROD ASSEMBLY, CONNECTING
BOLT, CONNECTING ROD
6
CLIP, PISTON PIN 18MM
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 59
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
PAGE 60 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — RECOIL STARTER ASSY.
RECOIL STARTER ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
1
28400ZH8013ZB
28410ZH8003ZB
28420ZH8013
28422ZH8013
28433ZH8003
28441ZH8003
28442ZH8003
28443ZH8003
28461ZH8003
28462ZH8003
90003ZH8003
90008ZE2003
STARTER ASSY., RECOIL "NH1" BLACK ...................1 ............INCLUDES ITEM W/
*
2
CASE, RECOIL STARTER "NH1" BLACK
REEL, RECOIL STARTER
RATCHET, STARTER
GUIDE, RATCHET
SPRING, FRICTION
SPRING, RECOIL STARTER
SPRING, RETURN
KNOB, RECOIL STARTER
ROPE, RECOIL STARTER
SCREW, SETTING
1
1
2
1
1
1
2
1
1
1
3
*
3
*
4
*
5
*
6
*
7
*
8
*
9
*
10
*
11
*
12
BOLT, FLANGE 6 X10
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 61
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — GASKET KIT ASSY.
NO ARTWORK AVAILABLE
PAGE 62 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — GASKET KIT ASSY.
GASKET KIT ASSY.
NO.
PART NO.
PART NAME
QTY.
REMARKS
06111ZH8405
11381ZH8801
12251ZF1800
12391ZE1000
16212ZH8800
16221ZH8801
18381ZH8800
GASKET KIT ......................................................... 1............ INCLUDES ITEMS W/
*
1
*
2
*
3
*
4
*
5
*
6
*
GASKET CASE COVER (NON- ASBESTOS)
GASKET, CYLINDER HEAD
GASKET, CYLINDER HEAD COVER
GASKET, INSULATOR
GASKET, CARBURETOR
GASKET, MUFFLER
1
1
1
1
1
1
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 63
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — LABELS ASSY.
L ABELS ASSY.
PAGE 64 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
HONDA GX160K1QX2 ENGINE — LABELS ASSY.
ENGINE LABELS ASSY.
NO.
1
2
3
6
7
8
15
PART NO.
PART NAME
QTY.
REMARKS
87521ZH8020
87522ZE1810
87522ZH9000
87528ZE1810
87530ZH8810
87532ZH8810
887586ZH7W00
ENBLEM 5.5
1
1
1
1
1
1
1
MARK, CAUTION (EXTERNAL)
LABEL, CAUTION
MARK, CHOKE
LABEL, SPECIFICATION (EXTERNAL)
MARK, OIL ALERT (E)
LABEL, FUEL CAUTION
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 65
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective: July 15, 2003
TERMS AND CONDITIONS OF SALE — PARTS
PAYMENT TERMS
5. Partsmustbeinnewandresalablecon- Multiquipreservestherighttoquoteandsell
dition,intheoriginalMultiquippackage(if directtoGovernmentagencies,andtoOriginal
any), and with Multiquip part numbers Equipment Manufacturer accounts who use
Terms of payment for parts are net 30 days.
FREIGHTPOLICY
clearlymarked.
our products as integral parts of their own
products.
All parts orders will be shipped collect or
prepaidwiththechargesaddedtotheinvoice.
All shipments are F.O.B. point of origin.
Multiquip’sresponsibilityceaseswhenasigned
manifesthasbeenobtainedfromthecarrier,
andanyclaimforshortageordamagemustbe
settledbetweentheconsigneeandthecarrier.
6. Thefollowingitemsarenotreturnable:
SPECIALEXPEDITINGSERVICE
a. Obsolete parts. (If an item is in the
price book and shows as being re- A$35.00surchargewillbeaddedtotheinvoice
placedbyanotheritem,itisobsolete.) forspecialhandlingincludingbusshipments,
insuredparcelpostorincaseswhereMultiquip
mustpersonallydeliverthepartstothecarrier.
(such as gaskets, seals, “O” rings,
b. Any parts with a limited shelf life
andotherrubberparts)thatwerepur- LIMITATIONSOFSELLER’SLIABILITY
MINIMUMORDER
chasedmorethansixmonthspriorto
thereturndate.
Multiquip shall not be liable hereunder for
damagesinexcessofthepurchasepriceofthe
The minimum charge for orders from Mul-
tiquipis$15.00net.Customerswillbeasked
for instructions regarding handling of orders
notmeetingthisrequirement.
c. Anylineitemwithanextendeddealer item with respect to which damages are
netpriceoflessthan$5.00.
claimed, and in no event shall Multiquip be
liable for loss of profit or good will or for any
otherspecial,consequentialorincidentaldam-
ages.
d. Special order items.
RETURNEDGOODSPOLICY
e. Electricalcomponents.
f. Paint,chemicals,andlubricants.
g. Decalsandpaperproducts.
h. Itemspurchasedinkits.
Returnshipmentswillbeacceptedandcredit
willbeallowed,subjecttothefollowingprovi-
sions:
LIMITATIONOFWARRANTIES
Nowarranties,expressorimplied,aremade
in connection with the sale of parts or trade
accessoriesnorastoanyenginenotmanufac-
tured by Multiquip. Such warranties made in
connectionwiththesaleofnew,completeunits
are made exclusively by a statement of war-
rantypackagedwithsuchunits,andMultiquip
neitherassumesnorauthorizesanypersonto
assume for it any other obligation or liability
whatever in connection with the sale of its
products.Apartfromsuchwrittenstatementof
warranty, there are no warranties, express,
impliedorstatutory,whichextendbeyondthe
descriptionoftheproductsonthefacehereof.
1. AReturnedMaterialAuthorizationmust
be approved by Multiquip prior to ship-
ment.
7. Thesenderwillbenotifiedofanymaterial
receivedthatisnotacceptable.
2. ToobtainaReturnMaterialAuthorization,
alistmustbeprovidedtoMultiquipParts
Salesthatdefinesitemnumbers,quanti-
ties, and descriptions of the items to be
returned.
8. Suchmaterialwillbeheldforfiveworking
days from notification, pending instruc-
tions.Ifareplyisnotreceivedwithinfive
days,thematerialwillbereturnedtothe
senderathisexpense.
a. Thepartsnumbersanddescriptions
must match the current parts price
list.
9. Creditonreturnedpartswillbeissuedat
dealer net price at time of the original
purchase,lessa15%restockingcharge.
b. The list must be typed or computer
generated.
10. In cases where an item is accepted, for
which the original purchase document
can not be determined, the price will be
basedonthelistpricethatwaseffective
twelvemonthspriortotheRMAdate.
c. The list must state the reason(s) for
thereturn.
d. The list must reference the sales
order(s)orinvoice(s)underwhichthe
itemswereoriginallypurchased.
11. Credit issued will be applied to future
purchasesonly.
e. The list must include the name and
phonenumberofthepersonrequest-
ingtheRMA.
PRICINGANDREBATES
Prices are subject to change without prior
notice.Pricechangesareeffectiveonaspe-
cificdateandallordersreceivedonorafterthat
datewillbebilledattherevisedprice.Rebates
3. AcopyoftheReturnMaterialAuthoriza-
tionmustaccompanythereturnshipment.
4. Freight is at the sender’s expense. All forpricedeclinesandaddedchargesforprice
partsmustbereturnedfreightprepaidto increaseswillnotbemadeforstockonhand
Multiquip’sdesignatedreceivingpoint.
atthetimeofanypricechange.
PAGE 66 — G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06)
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE PAGE
G-55H GASOLINE VIBRATOR — OPERATION & PARTS MANUAL — REV. #0 (03/07/06) — PAGE 67
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION AND PARTS MANUAL
HERE'S HOW TO GET HELP
PLEASE HAVETHE MODEL AND SERIAL
NUMBER ON-HANDWHEN CALLING
UNITED STATES
Multiquip Corporate Office
18910 Wilmington Ave.
Carson, CA 90746
MQ /STOWParts Department
Tel. (800) 421-1244
Fax (800) 537-3927
800-427-1244
310-537-3700
Fax:800-672-7877
Fax:310-637-3284
Contact: [email protected]
Mayco Parts
800-306-2926
310-537-3700
Warranty Department
800-421-1244, Ext. 279 Fax:310-537-1173
310-537-3700, Ext. 279
Fax:800-672-7877
Fax:310-637-3284
Service Department
800-421-1244
Technial Assistance
800-478-1244
Fax:310-537-4259
Fax:310-631-5032
310-537-3700
MEXICO
MQ Cipsa
UNITED KINGDOM
Multiquip (UK) Limited Head Office
Hanover Mill, Fitzroy Street,
Ashton-under-Lyne,
Carr. Fed. Mexico-Puebla KM 126.5
Momoxpan, Cholula, Puebla72760Mexico
Tel: (52) 222-225-9900
Fax: (52) 222-285-0420
Tel: 0161 339 2223
Fax: 0161 339 3226
Lancashire OL7 0TL
CANADA
Multiquip
BRAZIL
Multiquip
4110IndustrielBoul.
Laval, Quebec, Canada H7L 6V3
Tel: (450) 625-2244
Fax: (450) 625-8664
Av. Evandro Lins e Silva, 840 - grupo 505 Tel: 011-55-21-3433-9055
Barra de Tijuca - Rio de Janeiro Fax: 011-55-21-3433-9055
© COPYRIGHT 2006, MULTIQUIP INC.
Multiquip Inc, the MQ logo and the STOW logo are registered trademarks of Multiquip Inc. and may not be used, reproduced, or altered without written permission. All other
trademarks are the property of their respective owners and used with permission.
This manual MUST accompany the equipment at all times. This manual is considered a permanent part of the equipment and should remain with the unit if resold.
The information and specifications included in this publication were in effect at the time of approval for printing. Illustrations are based on the MQ/STOW G-55H Gasoline
Vibrator. Illustrations, descriptions, references and technical data contained in this manual are for guidance only and may not be considered as binding. Multiquip Inc.
reserves the right to discontinue or change specifications, design or the information published in this publication at any time without notice and without incurring any
obligations.
Your Local Dealer is:
Download from Www.Somanuals.com. All Manuals Search And Download.
|