Voice / Fax over IP Networks
Standalone Voice/IP Gateway
Model MVP200
Proprietary Mode
Quick Start Guide
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Introduction ................................................................................... 4
Related Documentation ................................................................. 5
Installing Your MultiVOIP............................................................... 6
Unpacking Your MultiVOIP ............................................................ 8
Safety Warnings ............................................................................ 8
Cabling Your MultiVOIP................................................................. 9
E&M Jumper Block Positioning Procedure ..................................11
Configuring Your Host MultiVOIP ................................................ 13
Configuring Your ClientMultiVOIPs.............................................. 29
Deploying the VOIP Network....................................................... 38
Limited Warranty ......................................................................... 41
Technical Support........................................................................ 42
Contacting Technical Support ............................................... 42
FCC Declaration.......................................................................... 43
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
Introduction
Welcome to Multi-Tech's stand-alone Voice/IP Gateway, the
MultiVOIP, model MVP200. The MultiVOIP allows analog voice
and fax communication over an IP network. Multi-Tech’s new
voice/fax gateway technology allows voice and fax
communication to ride, with no additional expense, over your
existing IP network, which has traditionally been data-only. To
access this free voice and fax communication, all you have to do
is connect the MultiVOIP to your telephone equipment, and then
to your existing Internet connection. Once configured, the
MultiVOIP then allows voice and fax to travel down the same path
as your traditional data communications.
The MVP200 has two independent voice/fax channels (each with
three voice/fax interfaces), a 10 Mbps Ethernet LAN interface,
and a command port for configuration.
System management is provided through the command port
using bundled Windows® software which provides easy-to-use
configuration menus and online Help.
Figure 1. MultiVOIP
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Related Documentation
The MultiVOIP200 Quick Start Guide is intended to be used by
qualified systems administrators and network managers. This
quick start provides the necessary information for a qualified
person to unpack, cable, load software, and configure the unit
for proper operation.
A detailed MultiVOIP200 User Guide is also provided on the
system CD with your unit and provides in-depth information on
the features and functionality of Multi-Tech’s MultiVOIP.
The User Guide is produced using Adobe AcrobatTM. To view
or print your copy of a user guide, install Acrobat ReaderTM on
your computer. The Acrobat Reader is included on your
system CD or is available as a free download from Adobe’s
Once loaded on your computer, launch the Reader and select
the .pdf file from the CD.
The MultiVOIP200 User Guide is also available on Multi-Tech’s
Viewing and printing a user guide from the Web also requires
that you have the Acrobat Reader loaded on your system. To
select the MultiVOIP200 User Guide from the MTS home page,
click Support | Manuals and then click MultiVOIP in the product
list. All MultiVOIP documents will be displayed and you can
choose User Guide (MVP200) to view or download the .pdf file.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
Installing Your MultiVOIP
The basic steps of installing your MultiVOIP network involve
unpacking the units, connecting the cables, and configuring
the units using the included management software (MultiVOIP
Configuration). The recommended installation process
includes three phases that, when completed, result in a fully
functional Voice Over IP network. A general description of
each phase is provided below, and detailed instructions follow
throughout the rest of this section.
Configure and Install Your Host MultiVOIP
As the first step, the VOIP administrator configures the
MultiVOIP designated as the “Host” unit. This includes the
assignment of a unique LAN IP address, subnet mask, and
Gateway IP address; as well as the selection of appropriate
channel interface type for each of the Voice/Fax channels.
Once all connections have been made, the VOIP administrator
configures the unit and builds the Phone Directory Database
that will reside with the Host unit.
Configure Your Client MultiVOIPs
Once installation has been completed, the administrator
moves on to configure the MultiVOIPs designated as “Client”
units. Again, unique LAN IP addresses, subnet masks, and
Gateway IP addresses are assigned, and each Voice/Fax
channel is configured for the appropriate channel interface
type. When this is done, the Phone Directory Database option
is set to Client, and the IP address of the Host MultiVOIP is
entered. Once all Client units are configured, the VOIP
network can be deployed.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Introduction
Deploy the VOIP Network
The final phase of the installation is deployment of the
network. Through the first two phases, the VOIP administrator
controls configuration, so when the Client MultiVOIPs are sent
to their remote sites, the remote site administrators need only
to connect the units to their LAN and telephone equipment. A
full Phone Directory Database (supplied by the Host
MultiVOIP) will be loaded into their unit within minutes of being
connected and turned on.
The final task of the VOIP Administrator is to develop the VOIP
Dialing Directory based on the Phone Directory Database and
telephone numbers of the interfacing telephone equipment; at
which point, a VOIP user can call any person on the VOIP
network.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
Unpacking Your MultiVOIP
Remove all items from the box (See Figure 2).
200
Voice/Fax over IP Networks
.A
S
U.
MADE IN U.S.A
IN
E
D
A
M
Figure 2. Unpacking
Safety Warnings
Caution: Danger of explosion if battery is incorrectly replaced.
A lithium battery on the voice/fax channel board provides
backup power for the time keeping capability. The battery has
an estimated life expectancy of ten years.
When the battery starts to weaken, the date and time may be
incorrect. If the battery fails, the board must be sent back to
Multi-Tech Systems for battery replacement.
The E&M, FXS, and Ethernet ports are not designed to be
connected to a Public Telecommunication Network.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling
Cabling Your MultiVOIP
Cabling your MultiVOIP involves making the proper Power,
Command Port, phone system, and Internet connections.
Figure 3 shows the back panel connectors and the associated
cable connections. The following procedure details the steps
necessary for cabling your MultiVOIP.
Before starting to cable your MultiVOIP, perform the E&M
Jumper Block Positioning Procedure, which immediately
follows the Cabling Procedure, if either voice/fax channel (1 or
2) will be connected to an E&M trunk that is a Type 1, 3 ,4, or
5 rather than a Type 2 (the default).
1. Connect the power supply to a live AC outlet, then connect
it to the MultiVOIP as shown in Figure 3. The power
connector is a 6-pin circular DIN connector.
Voice/Fax Channel 1
Voice/Fax Channel 2 Ethernet RS232
1
0
E&M
FXS
FXO
FXO
FXS
E&M
Command
10Base-T
Power
Power Connection
Voice/Fax Channel
1 & 2 Connections
E&M
FXO
FXS
Command Port Connection
PBX
PSTN
Network Connection
Hub
Figure 3. Cable Connections
2. Connect the MultiVOIP to a PC using the RJ-45 to DB9
(female) cable provided with your unit. Plug the RJ-45 end
of the cable into the Command port of the MultiVOIP and
connect the other end to the PC serial port you are using.
See Figure 3.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
3. Connect a network cable to the Ethernet 10BASE-T
connector on the back of the MultiVOIP. Connect the other
end of the cable to your network.
4. If you are connecting a station device such as an analog
telephone, a fax machine, or a Key Telephone System
(KTS) to your MultiVOIP, connect the smaller end of a
special adapter cable (supplied) to the Voice/Fax Channel
1 FXS connector on the back of the MultiVOIP and the
other end to the station device.
If you are connecting a PBX extension to your MultiVOIP,
connect the smaller end of a special adapter cable
(supplied) to the Voice/Fax Channel 1 FXO connector on
the back of the MultiVOIP and the other end to the PBX
extension.
If you are connecting an E&M trunk from a telephone
switch to your MultiVOIP, connect one end of an RJ-45
phone cord to the Voice/Fax Channel 1 E&M connector
on the back of the MultiVOIP and the other end to the
trunk.
If you are connecting to an E&M trunk, you need to ensure
that the E&M trunk jumper is in the correct position for the
E&M type trunk. The default E&M jumper position is E&M
type 2. To change the E&M jumper position, perform the
E&M jumper block positioning procedure, which
immediately follows this procedure.
5. Repeat the above step to connect the remaining telephone
equipment to each Voice/Fax Channel on your MultiVOIP.
6. Turn on power to the MultiVOIP by setting the power
switch on the back panel to the 1 (up, On) position. Wait
for the Boot LED on the MultiVOIP to go off before
proceeding. This may take a couple of minutes.
Proceed to the Software Loading section to load the MultiVOIP
software.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Cabling
E&M Jumper Block Positioning Procedure
Each voice/fax channel on the MultiVOIP has a separate E&M
jumper block, located near the jacks on the back panel of the
MultiVOIP. Each jumper block has 8 pairs of pins with a
jumper plug on three adjacent pairs of pins. The jumper plug
must be centered on the E&M type number (see Figure 4) that
matches the E&M connection for that channel. Perform the
following procedure if you need to move the E&M jumper block
from its default (Type 2) position.
1. Ensure that the external power supply is disconnected
from the MultiVOIP.
2. Turn the MultiVOIP upside down and remove the cabinet
mounting screw at the center back of the cabinet.
3. Turn the MultiVOIP right side up, then slide the base out
the rear of the cabinet.
Note: To change a jumper position, lift the jumper plug up
off the jumper block, then move it to the new position,
ensuring that the middle jumper of the jumper block is
centered on the E&M type number (1, 3, 4, or 5) as shown
in Figure 4.
Back Panel Connectors
Jumper Blocks
In Position 2
(Default)
2
2
Channel 2
Channel 1
1,3
4
Alternate Positions
5
Note: Markings do not appear on board.
Figure 4. E&M Jumper Block Positions
11
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
4. Change the jumper block position for any voice/fax
channel to be connected to an E&M trunk that is not a
Type 2 (the default position).
5. Slide the base all the way into the cabinet until it stops.
6. Turn the MultiVOIP 200 upside down and replace the
cabinet mounting screw that was removed in step 2.
7. Return the MultiVOIP 200 to its upright position, then
perform the cabling procedure.
8. Return to the Cabling Procedure.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
Configuring Your Host MultiVOIP
Configuring your Host MultiVOIP involves software loading and
configuration.
The software loading procedure does not provide every screen
or option in the loading process. It is assumed that a technical
person with a thorough knowledge of Windows and the
software loading process is performing the installation.
Additional information on the MultiVOIP software is provided in
the User Guide supplied with your MultiVOIP.
If you are installing a MultiVOIP behind a firewall, you need to
add the following UDP ports to your firewall.
Q.931 Signaling, Ch1 [900]
Status [5000]
Q.931 Signaling, Ch2 [902]
Ch1 RTP [5004]
Ch1 RTCP [5005]
Ch2 RTCP [5007]
Ch2 RTP [5006]
Refer to your firewall user documentation to enter and open
these ports.
1. Make certain that your MultiVOIP 200 has been properly
cabled and that the power is turned on.
2. Insert the MultiVOIP 200 CD into your CD-ROM drive. The
CD should start automatically. It may take 10 to 20
seconds for the MultiTech CD installation window to
display.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
If the Multi-Tech Installation CD window does not display
automatically, click My Computer, then right click the CD
ROM drive icon, click Open, and then click the Autorun
icon.
3. When the Multi-Tech Installation CD dialog box displays,
click the Install Software icon.
4. The Welcome dialog box displays.
Press Enter or click Next to continue.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
5. Follow the on-screen instructions to install your MultiVOIP
software.
6. The following dialog box selects the COM port of your PC
connected to the Command port of the MultiVOIP. From
the Select Port list, choose the COM port of your PC.
Click OK to continue.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
7. The Setup Complete dialog displays.
Click Finish to continue.
8. The following message displays:
Click No to continue.
9. In the v. 201E program group, double-click Upgrade
Software.
10. The following window displays.
Click Yes to continue.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
11. The IP Protocol Default Setup dialog box displays.
The default FrameType is TYPE_II. If this does not match
your IP network, change the Frame Type by selecting SNAP
from the FrameType list. The available Frame Type choices
are TYPE_II and SNAP.
12. In the Ethernet group, enter your unique LAN IP address in
the IP Address box, then enter the Subnet Mask and
Gateway Address for your LAN in the corresponding
boxes.
The IP address is your unique LAN IP address, and the
Gateway address is the IP address of the device
connecting your MultiVOIP to the Internet.
Click OK when you are finished.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
13. The Channel Setup dialog box displays. It is used to
define the voice/fax channel interface, voice coder, fax
parameters, billing options, security settings, and regional
phone parameters (tone pairs) for each channel.
Configure each channel for the type of interface you are
connecting to. To change the channel number, select the
channel you want to configure from the Select Channel
list.
14. The Interface group defaults to FXS (Loop Start). Select
the interface option to correspond to the interface type
being connected to the Voice/Fax connector on the back
panel of the MultiVOIP.
If you are connecting a station device such as an analog
telephone, a fax machine, or a Key Telephone System
(KTS) to the Voice/Fax connector on the back of the unit,
FXS (Loop Start) will likely be the correct Interface option
most of the time.
If the station device uses ground start, then choose the
FXS (Ground Start) option. Refer to the device’s user
documentation.
If you are using an extension from your PBX, then choose
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
the FXO option. Check with your in-house telephone
personnel to verify connection type.
If you are connecting to an E&M trunk on your PBX, then
choose E&M option.
If the E&M interface is selected, the E&M Options group is
enabled. Check with your in-house phone personnel to
determine if the signaling is DialTone or Wink and if the
connection is 2-wire or 4-wire. If Wink signaling is used,
then the Wink Timer is enabled with a default of 250
milliseconds. The range of the Wink Timer is from 100 to
350 milliseconds. Consult with your local in-house phone
personnel for this timer setting. If the PassThrough
check box is selected, a continuously open E&M voice
path is established between two channels to pass voice
packets. Available if the Dial Tone option is selected and
auto-dialing is set up for the two channels that will be
doing pass-through. This is useful for Public Address
systems.
If you choose an FXO or FXS interface, the Dialing
Options Regeneration group is enabled. Check with your
in-house telephone personnel to verify whether your local
PBX dial signaling is Pulse or DTMF (tone). Set the
Regeneration option accordingly. In the Max Dial Digits
box, enter the maximum number of digits allowed when
dialing a phone number. The default setting is 5. In the
Inter DigitTime box, enter the maximum amount of time
in milliseconds that the unit will wait before mapping the
dialed digits to an entry in the Phone Directory Database.
If too much time elapses between digits and the wrong
numbers are mapped, you hear a rapid busy signal. If this
happens, hang up and dial again. This option is available
for all interface types. In the Flash Timer box, enter the
time, in milliseconds, for the duration of flash hook signals
output on the FXO or FXS interface.
For FXO-to-FXO communications, you can enable a
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
specific type of FXO Disconnect: current loss, tone
detection, or silence detection. Check with your in-
house phone personnel to verify the preferred type of
disconnect to use. For tone detection, you can select
from the lists either one or two tones that will cause the
line to disconnect. The person hanging up a call must then
hit the key or keys that will produce those tones. For
silence detection, select OneWay or Two Way, then set
the timer for the number of seconds of silence before
disconnect. The default value of 15 seconds may be
shorter than desired for your application.
To dedicate a local voice/fax channel to a remote voice/fax
channel, (so you will not have to dial the remote channel)
select the Auto Call Enable check box. Enter the phone
number of the remote VOIP in the Phone Number box.
The FXS Options control how the selected channel
interacts with answering machines. If the Current Loss
check box is selected, the local VOIP hangs up when the
electrical current is lost. The remote VOIPs must also be
configured for current loss. The Ring Count box contains
the number of rings before the caller hears a fast Busy
signal. If this happens, hang up and try again. The default
setting is 8 rings.
Note: After configuring a given channel, you can copy that
channel’s configuration to any other channel by clicking
Copy. Everything on the Interface tab will be copied to
the other channel.
15. Repeat the above steps to configure the interface type for
each voice/fax channel.
The Voice/Fax tab displays the parameters for the voice
coder, faxing, and DTMF gain.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
16. To change the voice coder, select the channel from the
Select Channel list, then select the new voice coder entry
from the Voice Coder list.
If you changed the voice coder, ensure that the same voice
coder is used on the voice/fax channel you are calling.
Otherwise, you will always get a busy signal.
17. If you selected the FXO interface and are using touchtone
dialing, you can set up the DTMF gain (or output level in
decibels - dB) for the higher and lower frequency groups
of the DTMF tone pair. Make your selections from the lists
in the DTMF Gain group. In the Duration box, enter the
DTMF tone duration in milliseconds. 100 is entered by
default.
Note: Only change the DTMF gain under the direction of
Multi-Tech Technical Support.
18. The Fax group enables you to send and receive faxes on
the selected voice/fax channel. You can select the
maximum baud rate for faxes from the list in the Fax
group. If you do not plan to send or receive faxes on a
given voice/fax channel, you can disable faxes in the Fax
group.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
Note: After configuring a given channel, you can copy
that channel’s configuration to any other channel by
clicking Copy. Everything on the Voice/Fax tab will be
copied to the other channel.
19. The Billing/Security tab displays the parameters for
automatic disconnection, billing options, and dialing
options.
20. You can set up billing options for inbound and outbound
calls by selecting them in the Billing Options group and
then entering the charge in cents per number of
seconds.
21. The Call Authentication option enables password
protection for outbound and inbound calls on the
selected voice/fax channel. If you enable password
protection on inbound or outbound calls, you need to
also enter a password of up to 14 numeric characters in
the Password box.
22. The Automatic Disconnect option limits call duration to
the number of seconds entered in the Disconnect After
box. The default value of 180 seconds can be changed
to any other value up to 65,535 (roughly 18.2 hours).
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
If your country/region is not the default USA, click the
Regional tab and proceed to step 23. Otherwise, proceed
to step 24 to begin building your phone directory database.
23. To change the Tone Pairs on the Regional tab, select your
country or region from the Country/Region list.
The Tone Pairs group parameters change per your choice.
Click OK when finished.
24. The following dialog box displays.
Click OK. Proceed to step 25 to begin building your phone
directory database when the upgrade is complete.
25. From the Program Group, double-click MultiVOIP
Configuration. Click Phone Book. The Phone
Directory Database dialog box displays. You will build
your personalized MultiVOIP Phone Directory in the
following steps.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
The MultiVOIP configured as a “Host” will contain the host
database. The host database has the phone numbers of all
the MultiVOIPs available for communication on an IP
network. This database is downloaded to each Client
MultiVOIP as it comes online.
Click Add to begin building your phone directory database.
26. The Add/Edit Phone Entry dialog box displays.
In the Station Information group, enter the unique phone
number of the local device connected to Channel 1 in the
Phone Number box. For example phone number 101.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
27. The Description is optional, but can be useful in
associating the channel to the extension. If you want,
enter a description of your local phone number. This
description identifies the phone number you entered in the
previous step.
28. The Permit Hunting option enables the answering unit to
roll over to a second channel if the first channel is busy.
Click Permit Hunting if you want the calls to roll over to a
second voice/fax channel.
Note: The Host MultiVOIP must have a static IP address
that the remote MultiVOIP can reference to obtain a
downloaded copy of the host phone directory database.
29. In the MultiVOIP Identification group, enter the IP
address of the Host MultiVOIP in the IP Address box. For
example, 204.22.122.118.Then obtain the 12-digit Node
ID# (0008005xxxxx) from the ID plate on the back panel of
the MultiVOIP and enter this number in the Ethernet
Node ID box. If the ID plate is missing or damaged, you
can also Telnet to the MultiVOIP and, on the MultiVOIP
Telnet Server menu enter 1 to advance to the Main Menu,
then enter 3 for System Information where item 1 is the
Ethernet Port Address you want to enter in the Ethernet
Node ID box.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
30. Click OK and you are returned to the Phone Directory
Database dialog box, which now includes phone number
101 with its IP address, channel number, and description.
31. Click Add and the Add/Edit Phone Entry dialog box
displays again.
32. Enter the phone number for the remote MultiVOIP in the
Station Information group Phone Number box. For
example, 201.
33. Enter a description for the remote MultiVOIP phone
number for Channel 1 in the Description box.
Note: If the remote MultiVOIP is located behind a proxy
server that uses a dynamically assigned IP address, select
Dynamic (disabling Static IP Address) and leave the IP
Address box blank. The Host MultiVOIP will learn the IP
address when it is contacted by the remote MultiVOIP.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Host MultiVOIP
34. Enter the IP address of the remote MultiVOIP in the IP
Address box in the MultiVOIP Identification group. For
example, 202.56.39.100.
35. Click OK and you are returned to the Phone Directory
Database dialog box, which now includes the second
number and related information in the Phone Number list.
Note: If only Channel 1 is active, you must enter two
phone numbers. The first number will be the local
MultiVOIP phone number for Channel 1, and the second
number will be the remote MultiVOIP phone number for
Channel 1.
If both Channels 1 and 2 are active, four phone numbers
will have to entered.
36. When you have finished, click OK to download the setup
configuration to the MultiVOIP.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
37. The Checking MultiVOIP dialog box displays.
Click OK to proceed.
38. After the setup is written to the MultiVOIP, the unit is
rebooted.
39. Verify that the BOOT LED on the MultiVOIP is off after
the download is complete. This may take several
minutes as the MultiVOIP reboots.
40. You are returned to your MultiVOIP folder which is open
and visible on your desktop.
At this time, your host MultiVOIP is configured. Proceed to
the next section to configure the client MultiVOIPs.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Client MultiVOIPs
Configuring Your Client MultiVOIPs
If you are installing a MultiVOIP behind a firewall, you need to
add the following UDP ports to your firewall.
Q.931 Signaling, Ch1 [900] Q.931 Signaling, Ch2 [902]
Status [5000]
Ch1 RTP [5004]
Ch2 RTP [5006]
Ch1 RTCP [5005]
Ch2 RTCP [5007]
Refer to your firewall user documentation to enter and open
these ports.
1. Disconnect the PC from the command port of the Host
MultiVOIP and connect it to the command port on the
Client MultiVOIP.
2. From your desktop, click Start | Programs I MultiVOIP I
Upgrade Software. The following dialog box displays.
3. Click Yes. The IP Protocol Default Setup dialog box
displays.
The default FrameType is TYPE_II. If this does not match
your IP network, select the Frame Type from the Frame
Type list. The Frame Type choices are TYPE_II and
SNAP.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
4. In the Port Address group, enter the IP Address and IP
Mask. In the Gateway Address group, enter the gateway
IP address for the client unit.
The IP address is your unique LAN IP address, and the
Gateway address is the IP address of the device
connected to the Internet/Intranet.
Click OK when you are finished. The Channel Setup
dialog box displays.
5. The Channel Setup dialog box defines the channel
interface, voice coder, fax parameters, and regional
telephone parameters for each channel.
Configure each channel for the type of interface you are
connecting to. To change the channel number, select the
channel you want to configure from the Select Channel
list.
6. The Interface group defaults to FXS (Loop Start). Select
the interface option to correspond to the interface type
being connected to the Voice/Fax connector on the back
panel of the MultiVOIP.
If you are connecting a station device such as an analog
telephone, a fax machine, or a Key Telephone System
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Client MultiVOIPs
(KTS) to the Voice/Fax connector on the back of the unit,
FXS (Loop Start) will likely be the correct Interface option
most of the time.
If the station device uses ground start, then choose the
FXS (Ground Start) option. Refer to the device’s user
documentation.
If you are using an extension from your PBX, then choose
the FXO option. Check with your in-house telephone
personnel to verify connection type.
If you are connecting to an E&M trunk on your PBX, then
choose E&M option.
If the E&M interface is selected, the E&M Options group is
enabled. Check with your in-house phone personnel to
determine if the signaling is DialTone or Wink and if the
connection is 2-wire or 4-wire. If Wink signaling is used,
then the Wink Timer is enabled with a default of 250
milliseconds. The range of the Wink Timer is from 100 to
350 milliseconds. Check with your local in-house phone
personnel for this timer setting. If the PassThrough
check box is selected, a continuously open E&M voice
path is established between two channels to pass voice
packets. Available if the Dial Tone option is selected and
auto-dialing is set up for the two channels that will be
doing pass-through. This is useful for Public Address
systems.
If you choose an FXO or FXS interface, the Dialing Options
Regeneration group is enabled. Check with your in-house
telephone personnel to verify whether your local PBX dial
signaling is Pulse or DTMF (tone). Set the Regeneration
option accordingly. In the Max Dial Digits box, enter the
maximum number of digits allowed when dialing a phone
number. The default setting is 5. In the Inter Digit Time
box, enter the maximum amount of time in milliseconds
that the unit will wait before mapping the dialed digits to an
entry in the Phone Directory Database. If too much time
31
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
elapses between digits and the wrong numbers are
mapped, you hear a rapid busy signal. If this happens,
hang up and dial again. This option is available for all
interface types. In the FlashTimer box, enter the time, in
milliseconds, for the duration of flash hook signals output
on the FXO or FXS interface.
To dedicate a local voice/fax channel to a remote voice/fax
channel, (so you will not have to dial the remote channel)
select the Auto Call Enable check box. Enter the phone
number of the remote VOIP in the Phone Number box.
For FXO-to-FXO communications, you can enable a
specific type of FXO Disconnect: current loss, tone
detection, or silence detection. Check with your in-
house phone personnel to verify the preferred type of
disconnect to use. For tone detection, you can select
from the lists either one or two tones that will cause the
line to disconnect. The person hanging up a call must then
hit the key or keys that will produce those tones. For
silence detection, select OneWay or Two Way, then set
the timer for the number of seconds of silence before
disconnect. The default value of 15 seconds may be
shorter than desired for your application.
The FXS Options control how the selected channel
interacts with answering machines. If the Current Loss
check box is selected, the local VOIP hangs up when the
electrical current is lost. The remote VOIPs must also be
confirgured for current loss. The Ring Count box contains
the number of rings before the caller hears a fast Busy
signal. If this happens, hang up and try again. The default
setting is 8 rings.
Note: After configuring a given channel, you can copy that
channel’s configuration to any other channel by clicking
Copy. Everything on the Interface tab will be copied to
the other channel.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Client MultiVOIPs
7. Repeat the above steps to configure the interface type for
each voice/fax channel.
The Voice/Fax tab displays the parameters for the voice
coder, faxing, and DTMF gain.
8. To change the voice coder, select the channel from the
Select Channel list, then select the new voice coder entry
from the Voice Coder list.
If you changed the voice coder, ensure that the same
voice coder is used on the voice/fax channel you are
calling. Otherwise, you will always get a busy signal.
9. If you selected the FXO interface and are using touchtone
dialing, you can set up the DTMF gain (or output level in
decibels - dB) for the higher and lower frequency groups of
the DTMF tone pair. Make your selections from the lists in
the DTMF Gain group. In the Duration box, enter the
DTMF tone duration in milliseconds. 100 is entered by
default.
Note: Only change the DTMF gain under the direction of
Multi-Tech Technical Support.
10. The Fax group enables you to send and receive faxes on
the selected voice/fax channel. You can select the
33
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
maximum baud rate for faxes from the list in the Fax group.
If you do not plan to send or receive faxes on a given
voice/fax channel, you can disable faxes in the Fax group.
Note: After configuring a given channel, you can copy that
channel’s configuration to any other channel by clicking
Copy. Everything on the Voice/Fax tab will be copied to
the other channel.
11. The Billing/Security tab displays the parameters for
automatic disconnection, billing options, and dialing
options.
12. You can set up billing options for inbound and outbound
calls by selecting them in the Billing Options group and
then entering the charge in cents per number of seconds.
13. The Call Authentication option enables password
protection for outbound and inbound calls on the selected
voice/fax channel. If you enable password protection on
inbound or outbound calls, you need to also enter a
password of up to 14 numeric characters in the Password
box.
14. The Automatic Disconnect option limits call duration to
the number of seconds entered in the Disconnect After
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Configure Client MultiVOIPs
box. The default value of 180 seconds can be changed to
any other value up to 65,535 (roughly 18.2 hours).
If your country/region is not the default USA, click the
Regional tab and proceed to step 15. Otherwise, proceed
to step 16 to begin building your phone directory database.
15. To change the Tone Pairs on the Regional tab, select your
specific country or region from the Country/Region list.
The Tone Pairs group parameters change per your
selections. Click OK. The following dialog box displays.
16. Click OK after the upgrade is completed. Click Start |
Programs| MultiVOIP | MultiVOIP Configuration. On
the main menu, click Phone Book to display the Phone
Directory Database dialog box.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
In the DatabaseType group, click the Client option. The
Update Database From group becomes active.
17. Enter the IP address of the host MultiVOIP in the Host IP
Address box.
18. Click OK and you are returned to the main menu.
19. Click Download Setup to write the new configuration to
the client unit. The Save Setup dialog box displays.
20. Select the Save Current Setup as User Default
Configuration check box and click OK. After the setup is
written to the MultiVOIP, the unit reboots.
22. Check that the Boot LED on the MultiVOIP is off after the
download is complete. This may take several minutes as
the MultiVOIP reboots.
23. You are returned to the main menu.
Your MultiVOIP is operational at this time.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Deploy VOIP Network
Repeat this procedure for each of the client units. When all
clients have been configured, proceed with deploying the VOIP
network.
Deploying the VOIP Network
Deploying the VOIP network involves the VOIP Administrator
developing the VOIP Dialing Directory and deploying the pre-
configured client MultiVOIPs to their remote sites. The remote
site administrators need only connect power to the pre-
configured MultiVOIP, connect it to their Ethernet LAN and
predefined telephone equipment, and then wait for the phone
directory database to be downloaded.
Perform the following procedure to deploy your VOIP network.
VOIP Administrator
1. Establish your VOIP Dialing Directory based on your
Phone Directory Database for the numbers to connect the
MultiVOIPs to your VOIP network and the telephone
extension number you need to connect the Voice/Fax
channels. A sample VOIP Dialing Directory is provided
below for your consideration and use.
VOIP Dialing Directory
Call Process
Dialing
Sequence
To call from
2. Send the client MultiVOIPs to their remote sites.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
Remote Site Administrator
3. Unpack your MultiVOIP.
4. Connect one end of the power supply to a live AC outlet
and connect the other end to the Power connection on
your MultiVOIP.
Voice/Fax Channel
Connections
10BASET
E&M FXO FXS
ETHERNET
POWER
E&M
FXS
FXO
Power Connection
PSTN
Ethernet Connection
Figure 5. Remote Site Cable Connection
5. Connect a network cable to the ETHERNET 10Base-T
(RJ-45) connector on the back of your MultiVOIP.
6. If you are connecting a station device such as an analog
telephone, a fax machine, or a Key Telephone System
(KTS) to your MultiVOIP, connect the smaller end of a
special adapter cable (supplied) to the Voice/Fax Channel
1 FXS connector on the back of the MultiVOIP and the
other end to the station device.
If you are connecting a PBX extension to your MultiVOIP,
connect the smaller end of a special adapter cable
(supplied) to the Voice/Fax Channel 1 FXO connector on
the back of the MultiVOIP and the other end to the PBX
extension.
If you are connecting an E&M trunk from a telephone
switch to your MultiVOIP, connect one end of an RJ-45
phone cord to the Voice/Fax Channel 1 E&M connector
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Deploy VOIP Network
on the back of the MultiVOIP and the other end to the
trunk phone jack.
7. Repeat the above step to connect the remaining telephone
equipment to each Voice/Fax Channel on your MultiVOIP.
8. Turn on power to the MultiVOIP by placing the ON/OFF
switch on the back panel to the ON position. Wait for the
Boot LED on the MultiVOIP to go off before proceeding.
This may take a couple of minutes.
9. At this time your VOIP network should be fully operational.
Dial one of the sites in your network using the dialing
directory supplied by your Network Administrator.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
Limited Warranty
Multi-Tech Systems, Inc. (“MTS”) warrants that its products will
be free from defects in material or workmanship for a period of
two years from the date of purchase, or if proof of purchase is
not provided, two years from date of shipment. MTS MAKES
NO OTHER WARRANTY, EXPRESSED OR IMPLIED, AND
ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR A PARTICULAR PURPOSE ARE HEREBY
DISCLAIMED. This warranty does not apply to any products
which have been damaged by lightning storms, water, or
power surges or which have been neglected, altered, abused,
used for a purpose other than the one for which they were
manufactured, repaired by the customer or any party without
MTS’s written authorization, or used in any manner
inconsistent with MTS’s instructions.
MTS’s entire obligation under this warranty shall be limited (at
MTS’s option) to repair or replacement of any products which
prove to be defective within the warranty period, or, at MTS’s
option, issuance of a refund of the purchase price. Defective
products must be returned by Customer to MTS’s factory
transportation prepaid.
MTS WILL NOT BE LIABLE FOR CONSEQUENTIAL
DAMAGES AND UNDER NO CIRCUMSTANCES WILL ITS
LIABILITY EXCEED THE PURCHASE PRICE FOR
DEFECTIVE PRODUCTS.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Regulatory Information
Technical Support
Multi-Tech Systems has an excellent staff of technical support
personnel available to help you get the most out of your Multi-
Tech product. If you have any questions about the operation
of this unit, or experience difficulty during installation you can
contact Tech Support via the following:
Contacting Technical Support
Country
By E-mail
By
telephone
France:
India:
(33) 1-64 61 09 81
(91) 124-340778
(44) 118 959 7774
(800) 972-2439
(763) 785-3500
U.K.:
U.S. & Canada: [email protected]
Internet:
Please have your product information available, including
model and serial number.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
MultiVOIP Quick Start Guide
FCC Declaration
NOTE: This equipment has been tested and found to comply with
the limits for a Class A digital device, pursuant to Part 15 of the
FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is
operated in a commercial environment. This equipment
generates, uses and can radiate radio frequency energy, and if not
installed and used in accordance with the instructions, may cause
harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the
interference at his own expense.
Warning: Changes or modifications to this unit not expressly
approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Warranty and Regulatory Information
43
Download from Www.Somanuals.com. All Manuals Search And Download.
S000336A
Download from Www.Somanuals.com. All Manuals Search And Download.
|