Multi Link Cordless Telephone ML 001 User Manual

www.skylinkhome.com

Home Smart Center

MODEL: ML-001 / ML-100

CUSTOMER SERVICE

17 Sheard Avenue, Brampton, Ontario, Canada L6Y 1J3

Tel : (905) 456-8883

PATENTED

Fax : (905) 456-7819

Email : [email protected]

P/N. 101Z379-001

FEB, 2011

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

When using your telephone equipment, basic safety precautions should

always be followed to reduce the risk of fire, electric shock and injury to

persons, including the following:

1. Do not use this product near water, for example, near a bath tub, wash

bowl, kitchen sink or laundry tub, in a wet basement or near a swimming

pool.

2. Avoid using a telephone (other than a cordless type) during an

electrical storm. There may be a remote risk of electric shock from

lightning.

3. Do not use the telephone to report a gas leak in the vicinity of the leak.

4. Use only the power cord and batteries indicated in this manual. Do not

dispose of batteries in a fire. They may explode. Check with local codes

for possible special disposal instructions.

5. Plug the adaptor to the socket-outlet that near the equipment and

shall be easily accessible.

SAVE THESE INSTRUCTIONS

Attention

This product is not an alarm system providing facilities to summon

assistance, for use by persons who can be considered to be living

at risk. This product is not intended to for use in health care signaling

equipment or directly connect to central-station (Police, Medical, Fire).

–1–

Download from Www.Somanuals.com. All Manuals Search And Download.

IC Statement

Declaration of Conformity

‘’This product meets the applicable Industry Canada technical

specifications.”

Application of Council Directive(s) :

Radio Equipment and Telecommunication Terminal Equipment

Directive (1999/5/EC) - R&TTE

Before installing this equipment, users should ensure that it is permissible

to be connected to the facilities of the local telecommunications com-

pany. The equipment must also be installed using an acceptable method

of connection. In some cases, the company’s inside wiring associated

with a single line individual service may be extended by means of a

certified connector assembly (telephone extension cord). The customer

should be aware that compliance with the above conditions may not

prevent degradation of service in some situations.

Standard(s) to which Conformity is Declared:

EMC:

EN 55022:1998+A1: 2000, EN 610000-3-2: 2000,

EN 61000-3.3: 1995 +A1:2001, EN 55024: 1998+A1: 2001,

EN 50130-4: 1995/A1: 1998, EN 300220-3: 2000,

EN 301489-3: 2002

Safety:

Repairs to certified equipment should be made by an authorized Canadian

maintenance facility designated by the supplier. Any repairs or alterations

made by the user to this equipment, or equipment malfunctions, may give

the telecommunications company cause to request the user to disconnect

the equipment.

EN 60950-1: 2001, EN 50371: 2002

Telephony:

TBR 21: 1998

Manufacturer’s Name:

Capital Prospect Limited

..........................................................................................

Users should ensure for their own protection that the electrical ground

connections of the power utility, telephone lines and internal metallic water

pipe system, if present, are connected together. This precaution may be

particularly important in rural areas.

Manufacturer’s Address:

Room 3, 13/F, Block B, Veristrong Industrial Centre,

..........................................................................................

36 Au Pui Wan Street, Fo Tan, N.T., Hong Kong

..........................................................................................

Type of Equipment:

Model No.:

Home Smart Center

..........................................................................................

Caution: Users should not attempt to make such connections themselves,

but should contact the appropriate electric inspection authority, or electri-

cian, as appropriate.

AM-002

..........................................................................................

Serial No.:

Not Labelled

..........................................................................................

‘’The Ringer Equivalence Number is an indication of the maximum

number of terminals allowed to be connected to a telephone inter-

face. The termination on an interface may consist of any combination

of devices subject only to the requirement that the sum of the Ringer

Equivalence Numbers of all the devices does not exceed five.’’

Year of Manufacture:

2005

..........................................................................................

I, the undersigned, hereby declare that the equipment specified above conforms to the above

Directive (s) and Standard(s).

Place: Hong Kong

................................................

Joe Ng

Project Manager

Date:

21st July 2005

................................................

–55–

–2–

Download from Www.Somanuals.com. All Manuals Search And Download.

g) Should you experience trouble with this equipment, please contact

Skylink Customer Support at 1-800-304-1187 for repair or warranty

information. If the equipment is causing harm to the telephone network,

the telephone company may request that you disconnect the equipment

until the problem is resolved.

CONTENT

Introduction..........................................................................................................................4

Overview........................................................................................................................4

Installation...........................................................................................................................7

Installing the Console.................................................................................................7

Programming Passwords..........................................................................................9

Phone Number Programming..................................................................................10

Contact ID Phone number.......................................................................................12

Phone Number Programming (Calling to Central Monitoring Station)................12

Account Number Programming..................................................................................13

Deactivating the Digital Dialer.................................................................................14

Installing Door/Window Sensors................................................................................15

Installing Motion Sensor..........................................................................................16

Operation..........................................................................................................................18

Alert mode...................................................................................................................18

Mute....................................................................................................................................19

System Status..............................................................................................................20

Arming The System.....................................................................................................20

Disarming the system...............................................................................................21

Disarming a triggered control panel.....................................................................22

Disarming under Duress..........................................................................................22

Panic...................................................................................................................................23

System Failure............................................................................................................23

Phone Line Failure............................................................................................23

Sensor Failure.....................................................................................................24

Low Battery...........................................................................................................24

Coummunication.............................................................................................................26

Receiving an emergency call..................................................................................26

Remote Operation by Telephone...........................................................................27

To access the control panel away from home......................................................27

Advanced Programming.................................................................................................29

Zone Dependent Setting – Beep /Alarm..............................................................29

Zone Dependent Setting –Auto Mute....................................................................32

Zone Dependent Setting –Alert Zone (Bypass zone).........................................33

Learn Keychain / Keypad Remotes........................................................................35

Erase Keychain / Keypad Remotes........................................................................36

Learn Sensors..............................................................................................................37

Sensor Location Selection Guide.............................................................................37

Erase Sensors...........................................................................................................39

HomeAutomation.............................................................................................................40

Learn Control Modules............................................................................................40

Erase Control Modules............................................................................................43

Event Trigger..............................................................................................................45

Trouble Shooting..............................................................................................................47

Accessories......................................................................................................................49

System Configuration.....................................................................................................53

FCC Information................................................................................................................53

h) Please follow instructions for repairing if any (e.g. battery replacement

section); otherwise do not alternate or repair any parts of device except

specified.

i) Connection to party line service is subject to state tariffs. Contact the

state public utility commission, public service commission or corporation

commission for information.

j) NOTICE: If your home has specially wired alarm equipment connected to

the telephone line, ensure the installation of this modelAM-002 does not

disable your alarm equipment. If you have questions about what will

disable alarm equipment, consult your telephone company or a quali-

fied installer.

NOTICE: According to telephone company reports, AC electrical surges,

typically resulting from lightning strikes, are very destructive to telephone

equipment connected toAC power sources. To minimize damage from

these types of surges, a surge arrestor is recommended.

CE........................................................................................................................................55

–54–

–3–

Download from Www.Somanuals.com. All Manuals Search And Download.

FCC Information

INTRODUCTION

Consumer Information:

Overview

a) This equipment complies with Part 68 of the FCC rules and the require-

ments adopted by the ACTA. On the bottom of this equipment is a label

that contains, among other information, a product identifier in the format

US:AAAEQ##TXXXX. If requested, this number must be provided to the

telephone company.

Congratulations on your purchase of a Home Smart Center. This is a security

control panel which not only functions as a security system, but also monitors

your premises by giving you alert notification when the system is not armed. It

is also a home automation center, which allows you to remotely control house-

hold appliances and lights, even when you are away from home. It can be

controlled by dialing in from any touch tone phone, which makes it even more

convenient and powerful. Additional accessories such as different kinds of

sensors and controllers can be added to suit your specific needs.

b) An applicable certification jacks Universal Service Order Codes (USOC)

for the equipment is provided (i.e., RJ11C) in the packaging with each

piece of approved terminal equipment.

This user instructions will guide you through the whole setup procedure as well

as all the programming instructions. Please follow the instructions closely, you

should find it very easy to set up the system.

c) A plug and jack used to connect this equipment to the premises wiring

and telephone network must comply with the applicable FCC Part 68

rules and requirements adopted by theACTA.Acompliant telephone

cord and modular plug is provided with this product. It is designed to be

connected to a compatible modular jack that is also compliant. See

installation instructions for details.

Alert

Automation

When Home (System Not Armed)

Beep Beep

Alarm

d) The REN is used to determine the number of devices that may be con-

nected to a telephone line. Excessive RENs on a telephone line may

result in the devices not ringing in response to an incoming call. In most

but not all areas, the sum of RENs should not exceed five (5.0). To be

certain of the number of devices that may be connected to a line, as

determined by the total RENs, contact the local telephone company. [For

products approved after July 23, 2001, the REN for this product is part of

the product identifier that has the format US:AAAEQ##TXXXX. The digits

represented by ## are the REN without a decimal point (e.g., 03 is a

REN of 0.3). For earlier products, the REN is separately shown on the label.]

Not Home (System Armed)

Communicator

Zone 1

Sensor 1

Triggered

Alarm

In the package, you should find the following items:

•

One Control Panel

ML-001A

e) If this equipmentAM-002 causes harm to the telephone network, the

telephone company will notify you in advance that temporary discontinu-

ance of service may be required. But if advance notice isn’t practical, the

telephone company will notify the customer as soon as possible. Also,

you will be advised of your right to file a complaint with the FCC if you

believe it is necessary.

One Motion Sensor (For ML-100A Only)

Two Door / Window Sensors (For ML-100A Only)

PS-101

f) The telephone company may make changes in its facilities, equipment,

operations or procedures that could affect the operation of the equipment.

If this happens the telephone company will provide advance notice in

order for you to make necessary modifications to maintain uninterrupted

service.

WD-101

One Keychain Remote (For ML-100A Only)

4B-101

–4–

–53–

Download from Www.Somanuals.com. All Manuals Search And Download.

SYSTEM CONFIGURATION

INTRODUCTION

Master Password

____________________

•

One AC adapter

Secondary Password ____________________

Duress Password

____________________

•

One telephone cord

Sensor locations and settings

Batteries for all sensors (For ML-100A Only)

- 1 PC 9V Alkaline Battery (PS-101)

- 1 PC 12V Alkaline Battery Type 23A

(4B-101 -installed)

- 2 PCS 3V Lithium Battery CR-2032

(WD-101 -installed)

ZONE

SENSOR 1

SENSOR 2

BEEP / ALARM AUTO MUTE

Beep / Alarm Y / N

EVENT TRIGGER ALERT

Example

Front Door

Front Window

Disabled / On / Off

Y / N

•

Rechargeable battery of the Control Panel:

North American version

Phone number settings

PHONE MEMORY

PHONE NUMBER

321-123-4567

REDIAL COUNT

REPEAT COUNT

Example

European Version

Mounting hardware

Ball-head joint

(For ML-100A Only)

Keychain / Keypad Remotes settings

Mounting Plate

(For ML-100A Only)

KEYCHAIN / KEYPAD LOCATIONS

OWNER (KEYCHAIN) / LOCATION (KEYPAD)

Example

Keychain Owner - John

Screws

Pack

Basic installation involves the following procedures:

Control Modules settings

1. Install Control Panel ML-001A

2. Program Passwords

CONTROL MODULES

LOCATIONS / APPLIANCES

Example

Family room lighting

3. Program Phone Numbers

4. Install Door / Window Sensors WD-101 (For ML-100A Only)

–52–

^{5. Install Motion Sensor PS-101 (For M}–^L5^-1–^{00A Only)}

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

INTRODUCTION

Control Module SW-100

(US and Canada)

- To turn home appliances / lights on / off

]

- Max rating: 960W (Resistive)

Control Module SW-101U (UK), SW-101F

(French), SW-101G (German)

(3 models for 3 countries)

- To turn home appliances / lights on / off

Emergency Dialer (AD-433S)

- External dialer with user programmable voice

message

905-608-9223

- Calls up to 9 phone numbers

AD-433

- One personal voice recording up to 40 seconds

- Can be installed anywhere within 100 feet from

the control panel, with a phone socket

Swing door opener (DM-100)

- Remotely open / close a swing door

- Fits most interior doors

1. Zone LEDs

2. Numeric Keypad

3. Arm button

11. Built-in Siren and Speaker

12. Programming button

13. Buzzer Mode Selector

4. Status button

5. Mute button

6. Panic button

7. Power LED

8. Arm LED

14. Phone Jack for external phone

15. Line Jack for telephone line

16. Adapter socket

17. Battery Compartment

18. Language Selector (only available for

models support multiple languages)

9. Program LED

10. System Low Battery LED

–6–

–51–

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

INSTALLATION

Installing the Console

Audio Sensor (AS-101)

It is important determine where the control panel will be located. Please follow

the criteria below to select the ideal location for the control panel.

- When audio level exceeds preset limit, it will trigger the

alarm

- Place beside smoke detector, CO detector, so when these

Place it where electrical outlet and phone line can be accessed

Place it where it is easily accessible by the users

Place it away from any doors or windows which could be accessed by

non-intended users

detectors are triggered, the control panel will be triggered

Place is away from extreme temperature sources such as oven, stove

and away from large metal objects which could affect the wireless

performance

Remote Control (4B-101)

- Additional keychain remotes for other family members

- To arm, disarm or trigger the panic alarm with this remote

After a location has been selected, you may begin the installation and connect all

the necessary wires and power up the unit.

Keypad Control (KP-434)

- External keypad control

- To arm, disarm or trigger the the panic alarm with this

remote

1. Undo the 2 screws on the battery cover.

- Ideal mounting locations include upper floor, backdoor, or

garage

Wrist Watch Style Panic Remote (HW-101)

- Activate the panic alarm instantly with this remote

- Wear it as a watch

2. For models support multiple languages,

Language

select the desired language based on

selector

- Splashproof design, can be worn during showering

the setting below:

1. German

2. Spanish

3. French

4. English

Panic Transmitter (PT-101)

- Activate the panic alarm instantly with this remote

- Wear it as a pendant

- Splashproof design, can be worn during showering

3. Connect the power adapter to the

socket inside the battery compart-

ment. The power adapter should

be connected to an AC electrical

outlet. You should see all LEDs

turn on, LO BATT LED should be

off.

Audio Alarm (AA-433)

- External Siren

- Powered by AC adapter with backup battery

–50–

–7–

Download from Www.Somanuals.com. All Manuals Search And Download.

ACCESSORIES

INSTALLATION

4. Insert the rechargeable battery to the battery compartment. There are 2

different types of rechargeable battery for 2 markets:

Additional sensors and transmitters as well as add on accessories are available

to work with your system.

a. North American Version: Lead Acid

Connect the 2 wires to the battery. Red wire

connects to the “+” terminal on the battery.

Black wire connects to the “-” terminal on the

battery. Markings on the battery should face up.

Door/Window Sensor (WD-101)

- Magnetic Contact Sensor

- For all doors or windows

- Batteries included

b. European Version: Ni-MH

Plug in the wire from the battery to the battery

socket inside the battery compartment.

Repeater (RP-434)

- Extend the operation range between 2 wireless devices,

such as any sensors and control panel

- Doubles the operation range automatically between

sensors and control panel

5. After inserting the rechargeable battery, the LO

BATT LED will be off if the battery is fully

charged, otherwise it will be on.

6. Connect the phone line from the wall socket to

the “LINE” socket inside the battery

compartment.

Water Sensor (FS-101)

7. [OPTIONAL] If another telephone that will be

using the same telephone jack, you may

- Alerts you when water is detected

- Ideal for water detection in basement, under the sink, even

bathroom

connect this telephone to “PHONE” outlet of the

control panel by a phone cord (not provided).

(Optional)

8. The phone line(s), cord of the power adapter

should all come out from the lower right corner

of the control panel in order to close the battery

cover properly.

Garage Door Monitor^TMSensor (GS-101)

(Available in US and Canada)

- Monitors your garage door

- Alerts you when the garage door is left open

9. The battery cover can now be closed, and tighten

the 2 screws to secure the battery cover.

PWR, ARM, PROG LEDs should be flashing,

zone LEDs should be off.

Garage Door Monitor^TMSensor (GS-102)

(Available outside US and Canada)

- Monitors your garage door

10. The control panel is intended to be mounted on a

flat wall. 2 screws are required to mount the

control panel securely on the wall. It should not be

mounted too high or too low. In most situations, just

below eye level is ideal.

- Alerts you when the garage door is left open

7-1/8"

11. Once you have selected the mounting

location, tighten 2 screws on the wall.

They should be

Indoor/Outdoor Motion Sensor (PS-101)

- Monitors area in a 110 degree ARC and up to 40 feet away

from the sensor

7-1/8" apart from each other, on the same

horizontal level. Do not tighten the screws

all the way in, leave about 1/8" from the

wall in order for the control panel to be

hanged onto the wall.

–8–

–49–

Download from Www.Somanuals.com. All Manuals Search And Download.

TROUBLE SHOOTING

INSTALLATION

Programming Passwords

Sensors

Master Password can be used for programming, arming, disarming the

system, and telephone access. The default Master Password is [1234].

When a sensor is triggered, the

control panel doesn’t respond at all,

what is the problem?

- Make sure the battery in the sensor is

installed properly, pay attention to the

polarity.

- Make sure the sensor is learned to the

control panel. Follow instructions on

page 37 on how to learn a sensor.

- You may try to bring the sensor closer to

the control panel, ensure it is not out of

the operation range.

Secondary Password can be used for arming, disarming the system, and

telephone access. Secondary Password cannot be used for programming.

The default Secondary Password is [0000].

Duress Password is used when you are forcibly compelled to disarm the

control panel. Entering the duress password will stop the siren from sounding

but the control panel will silently call the emergency phone numbers for help.

The default Duress Password is [3838]. You should definitely change this

password and let all the users know this password.

My motion sensor sometimes gets

triggered by itself, how can I prevent

that?

Ensure the motion sensor is not facing

direct sunlight, nor any A/C or furnace

vents. You may also reduce the sensitivity

to low. If your motion sensor is located

outdoors, you may want to relocate it.

After mounting the door sensor, it

doesn’t work anymore.

- Please ensure the magnet is aligned with

the red marking on the transmitter.

Changing Passwords

- If you are mounting the sensor on to a

metal door or window, a spacer may be

required to avoid magnetic interference

caused by the metal door / window.

- Make sure the sensor is within the operation

range of the control panel by bringing it

closer to the control panel.

It is strongly recommended to change all 3 passwords when you first set

up the system.

In order to change the password, follow the procedures below.

Step

Keys

Function

Description

Note

[PROG]

Enter master

password to

programming mode

3 beeps for valid

password. 1 long

beep for invalid

password.

My motion sensor is not very

responsive, sometimes when I walk

by it, the control panel doesn’t respond,

but sometimes it does.

The motion sensor is designed to detect the

“First Motion”. First Motion means no motion

is detected within the past 20 seconds,

and if a motion is then detected, that is the

“First Motion”. So if you continue to walk

in front of the motion sensor, it will only

pick up the first motion. Unless you wait

for 20 seconds, then walk again, the control

panel will respond. Otherwise, the control

will only respond to the first motion.

Enter

Programming

mode

[MPIN]

[2]

Select

password

programming

[1] - Master password

[2] - Secondary password

[3] - Duress password

[1] or

[2] or

[3]

Select which

password to

change

[new

4-digit

password]

Select any 4-digit pass-

word, each digit can be

from 0 to 9

Enter new

password

[new

4-digit

password]

Enter new

password to

confirm

Enter the new password 3 beeps if new pass-

again for confirmation

word is accepted. You

will hear [Password

Accepted]

–48–

–9–

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

TROUBLE SHOOTING

Phone Number Programming

Control Panel

You can program up to 6 Emergency Phone Numbers. When the system is in panic,

the control panel will call these phone numbers and announce its status.

Questions

Solutions

Why I can’t arm my system?

Make sure none of the sensors are

triggered. You can check this by the zone

LEDs, none of them should blink.

The 6 emergency phone numbers include:

- 5 voice message phone numbers

- 1 Contact ID message phone number

I cannot arm the system even when no

sensor is triggered, and the ARM LED

is off.

You need to disarm the system again by

either entering the password or disarm by

keychain remote. Although the ARM LED

is off, but the system is not completely

disarmed after an alarm was triggered.

Refer to page 22 on how to completely

disarm a control panel after an alarm has

been triggered.

Program the following for Voice Message Phone Numbers

- Phone memory (from 1 to 5), this is where the phone numbers will be stored

- Phone number, up to 29 digits.

- Redial count, this is how many times that phone number will be called, from 1

to 9 times.

- Repeat count, this is how many times the emergency message will be repeated,

from 1 to 9 times.

Step

Keys

Function

Description

Note

Why the ARM LED keeps flashing?

That means you have not programmed any

emergency phone numbers. For instructions

on how to program emergency phone

numbers, please see page 10.

Enter

Programming

mode

Enter master password to

programming mode

3 beeps for valid

password. 1 long beep

for invalid password.

[PROG]

[MPIN]

Select phone

number

programming

You will hear [Enter

phone memory].

[1]

How do I exit programming mode

when I’m in the middle of it?

You can press the programming button on

the side of the unit to quit programming

anytime.

During emergency, phone

memory 1 will be called first,

then phone memory 2, 3, 4, and

5. So phone memory 1 has

higher priority.

Enter phone

memory

[1] to [5]

When a sensor is triggered, the alarm

sounds instantly even it is not armed,

why is that?

You have programmed that sensor in alarm

mode, instead of beep mode. Please refer

to page 29 for instructions of how to program

it back to beep mode.

Phone number can be up to 29

digits.**

You will hear [Enter

Redial].

[Phone

Enter phone

number] number

+ [Arm]

When the alarm is triggered, why

the control panel won’t call all the

programmed phone numbers? It

always stops before calling the

last number.

The control panel will stop calling when it

is disarmed by any one of the recipients.

Disarm can also be done locally thru the

keypad on the control panel by entering a

valid password.

You will hear [Enter

Repeat].

Redial is the number of times

that phone number will be

called. Each phone number

can have a different redial

count, from 1 to 9 times.

Enter Redial

[1] to [9]

+ [Arm]

count

Why the control panel doesn’t beep

when a sensor is triggered, while

only the zone LED flashes?

You have placed the buzzer mode selector

on the side of the control panel to “II”, this

will disable the beeping. Placing it to “I” will

enable the beeping.

Repeat is the number of times

that voice emergency message

will be played, from 1 to 9 times.

It is recommended to set up

the repeat time to 5 or more.

You will hear [Phone

Accepted] indicating the

phone number and its

settings have been

Enter Repeat

count

[1] to [9]

+ [Arm]

The control panel is in armed mode,

why activating a sensor will not cause

an alarm, or call any emergency phone

number?

If the triggered sensor is programmed in the

Alert Zone (Bypass Zone), alarm will not

sound, and emergency call will not be made

if this sensor is triggered. The control panel

will only respond when it is disarmed, in

alert mode.

programmed successfully.

**Note:

You may enter a 3-second pause between digits by pressing [Mute] if needed.

You may also enter consecutive multiple pause periods. For example, you may

enter a phone number: (123)-456-7890 [Mute] 1234. After the phone number

(123)-456-7890 is dialed, it will wait for 3 seconds, then dial 1234, which can be

a password to a paging system, or an access code for a phone dialing system.

–47–

–10–

Download from Www.Somanuals.com. All Manuals Search And Download.

HOME AUTOMATION

INSTALLATION

Note:

- It’s not recommended to program 911, fire station or any emergency services

phone numbers into any of the phone memories without their approvals.

- Ensure to program a valid phone number and write down the programmed

phone number on the System Setting Information provide on the back of this

user's instructions.

This row

Buttons to Disable Event Tigger

Zone LED : Off

- You may quit programming by pressing [PROG] button at any time.

- If no phone number is programmed, the ARM LED will continue to flash.

Press once will enable “Event Trigger On”,

press again will enable “Event Trigger Off”.

This row of buttons operates in toggle manner,

between event trigger on and event trigger off.

Testing Phone Numbers:

This row

Buttons to Enable Event Trigger

After you have programmed all the phone numbers, you should verify you have

programmed the phone numbers correctly. This can be done by triggering the

alarm silently by entering the duress password, so it dials to the programmed

phone numbers without sounding the alarm.

Zone LED : 1) On (Event Trigger On)

2) Flash (Event Trigger Off)

ENABLE EVENT TRIGGER

DISABLE EVENT TRIGGER

Button [1]

Note:

Zone 1

Zone 2

Button [6]

Button [7]

Button [8]

Button [9]

Button [0]

You must inform the recipients of the programmed phone numbers, so they know

what to expect when they receive the phone call from the control panel during an

emergency. These recipients should know the password to your control panel if

you expect them to have remote access of your control panel. For more informa-

tion regarding receiving the emergency call, please refer to page 26.

Button [2]

Button [3]

Zone 3

Zone 4

Zone 5

Button [4]

Button [5]

1. Press [Arm], you should hear beeping from the control panel.

2. Press [3838]. Beeping will stop, and the control panel will start to dial the first number.

3. The called party should receive the call. Pick up the call and say “Hello”, an

emergency message “System Panic” will be played. If the programmed phone

doesn’t ring, ensure the phone number is programmed correctly, or reprogram

this phone number again.

4. After the emergency message has been played for several times (depending on

how many times it was programmed), the called party will hear “Enter Password”.

5. Enter either the master password or secondary password. If the correct

password is accepted, you will hear “Password Accepted”, otherwise, you will

hear “Password Failure”.

6. Press [0][#] on the telephone to hang up.

7. The control panel will start to dial the next programmed phone number.

Note:

- Refer to page 26 [Receiving the Emergency Call] for more info on how to react

to an emergency call.

- The password is treated as a confirmation of the emergency message. Once a

valid password is entered, the control panel will not call that number again, it

will proceed to the next number.

- If any one of the called parties disarms the control panel, the control panel will

not continue to dial the remaining phone numbers.

- After calling all the programmed phone numbers, the control panel will be back

to the previous operation mode.

–46–

–11–

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

HOME AUTOMATION

Event Trigger

Contact ID Phone number

You can program a telephone number for calling to the central monitoring station.

When the system is in panic, the control panel will call this phone number and

will send out a Contact ID message with event code 140, which represents

“General Alarm”.

You can control up to 5 different devices not only manually, but also automatically. It is

called Event Trigger. That means when a sensor is triggered, the control panel will

transmit a signal to activate the designated control module. Applications include:

- Lights on when you open the front door

(walking into a room, lights on automatically),

this is called "Event Trigger on".

Follow the instructions below to program the necessary info in order to call a

monitoring station:

- Phone number of central monitoring station (up to 29 digits)

- Account number given by the Central Monitoring Station

- Lights off when you open a door. (walk away

from a room, turns lights off), this is called

"Event Triggered off".

Event Trigger On

Phone Number Programming (Calling to Central Monitoring Station)

Event trigger is only applicable to the sensor(s)

and control module in the same zone. For

example, you can program control module 1 to

be on or off when zone 1 sensor(s) is triggered.

You can also program control module 2 to be

on / off when zone 2 sensor(s) is triggered.

Step

Keys

Function

Description

Note

3 beeps for valid

password. 1 long

beep for invalid

Enter Program- Enter master

ming mode

Press [PROG]

Press [MPIN]

password to

programming mode

password.

Select phone

number

programming

Factory Default: This feature is disabled for

all zones at the factory.

You will hear

[Enter Phone

Memory]

Press [1]

Press [0]

Event Trigger Off

To change the event trigger setting follow the instructions below.

You will hear

[Phone Zero]

During emergency,

the Contact ID phone

number has the highest

priority, it will be the

first number to call.

Enter phone

memory

Step

Keys

Function

Description

Note

Enter master

password to

programming

mode

3 beeps for valid

password. 1 long beep

for invalid password.

Enter Program-

ming mode

[PROG]

[MPIN]

You will hear

Phone number

can be up to 29

digits.

Enter phone

number

Enter [Phone

number] +

[Arm]

Select Event

Trigger

After [7] is entered,

some zone LEDs will be

off, on or flash. This

indicates the setting of

event trigger.

[Phone Accepted]

indicating the phone

number has been

programmed

[7]

successfully.

Select which

zone you would

like to enable /

disable event

trigger.

If event trigger “ON” is

Disable Event

Trigger: [1] to

[5]

Refer to the

diagram below

to select the

appropriate

setting.

enabled, that zone LED will

be on. If event trigger “OFF”

is enabled, that zone LED

will flash. If it is disabled, the

zone LED will be off. You are

allowed to make multiple

changes before terminating

programming mode.

Enable Event

Trigger: [6] to

[0].

Terminate

programming

mode.

PROGLED

will be off.

[PROG]

when

finished.

–12–

–45–

Download from Www.Somanuals.com. All Manuals Search And Download.

HOME AUTOMATION

INSTALLATION

Account Number Programming

ZONE LED

Off

DESCRIPTION

In order to program the account number, follow the procedures follow:

Zone is not occupied by any control module

Flashes twice

That means a remote has occupied that zone.

THIS IS NOTACONTROLMODULE,THEREFORE, SHOULD NOTBE

ERASED.

Step

Keys

Function

Enter

Programming

mode

Description

Note

Enter master

password to

programming

Press [PROG]

Press [MPIN]

3 beeps for valid

password. 1 long beep

for invalid password.

Flashes once

That zone is occupied by a control module. You may select this

zone to erase this control module.

mode

Select

password

programming

Press [2]

Press [0]

Flashes once,

then twice

That means this zone is occupied by a remote AND a control module.

You may select this zone to erase the control module.

Select to

[0] = Add/change

add / change account number

account

number

** Table F: Zone LED status for erasing control module.

Enter new

account

number

Enter [New 4-

digit Account

Number]

Enter the 4-digit

account number

given by the

This number can be a

combination of 0-9,

B,C,D,E & F.

Part 2 Erase communication from Control Panel to Control Module

central monitoring

station.

Step

Keys

Function

Description

Note

To enter 0-9:

Enter by the keypad 0-9

directly.

Remove the

control module

from the

To enter B,C,D,E,F:

electrical outlet

Press [STATUS] and the

ARM light will stay on.

Then press the following

keys for the correspond-

ing letters (1=B, 2=C, 3=D,

4=E, 5=F).

Control module LED

will flash rapidly

indicating all the

memory is erased.

You may now

Press and hold

the learn button

on the control

module while

plugging in the

control module

to an electrical

outlet.

To erase the

memory of the

control module

Press [STATUS] to return

back to number-mode

when you want to input

numbers. The ARM light

will turn off.

release the learn

button.

You can toggle between

the number or letter mode

by pressing [STATUS]

when entering the

Once the memory of the control module is erased, all of its memory is cleared. If

you have other remotes / control panels controlling this control module, you need

to re-program those remotes / control panels.

account number.

Enter the new

account num-

ber again for

confirmation

3 beeps if new account

number is accepted. You

will hear [Password

Accepted]

Enter [New 4-

digit Account

Number]

–44–

–13–

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION

HOME AUTOMATION

Operation

Deactivating the Digital Dialer

To turn off a light with the control panel:

1. Press the device number button on the control panel, i.e. pressing 1 will turn

off device 1, pressing 2 will turn off device 2.

You can deactivate the digital dialer by erase the phone number memory for

central monitoring station.

2. You will hear [Device X Off], where X is the device number.

3. You will also see the PROG LED flashing, indicating the control panel is

sending out the wireless signal to control the specific device.

4. If the receiver receives the signal, the control panel will announce [Device

Off Accepted].

Step

Keys

Function

Description

Note

Enter Program- Enter master

ming mode

3 beeps for valid

password. 1 long

beep for invalid

password.

Press [PROG]

Press [MPIN]

password to

programming mode

To turn on a light with the control panel:

Press [1]

You will hear:

[Enter Phone

Memory]

Select phone

number

programming

1. Press the number below the device number that you would like to turn on, i.e.

pressing 6 will turn on device 1, pressing 7 will turn on device 2.

2. You will hear [Device X On], where X is the device number.

3. You will also see the PROG LED flashing, indicating the control panel is

sending out the wireless signal to control the specific device.

4. If the receiver receives the signal, the control panel will announce [Device

On Accepted].

Press [0]

Enter phone

memory

Press [ARM]

You will hear

[Phone Zero

Empty Memory]

indicating the phone

number have been

deleted, the digital

dialer is deactivated.

Confirm delete

the phone

number.

Erase Control Modules

To erase a control module from the control panel, it is similar to learning a

control module, which involves 2 parts.

Note: If no phone number is programmed to call the central monitoring station,

the digital dialer is automatically disabled.

1. Erase the memory of the control panel

2. Erase the memory of the control module

Part 1 Erase the memory of the Control Panel

Step

Keys

Function

Enter

Programming password to

Description

Note

3 beeps for valid

password. 1 long beep

for invalid password.

[PROG]

[MPIN]

Enter master

mode

programming mode

Select erase

control

module

After [0] is entered, some

zone LEDs will flash or

stay off. The zone LEDs

represent whether that zone

is occupied by any control

module. **See Table F

[0]

programming

To erase an

occupied

control module,

press [1] to [5].

After you have selected the

remote location, you will

hear 3 beeps and verbal

confirmation [Device X

Empty Memory], where

X is the control module

location you have selected.

Refer to the table

below to select

the control

Select the

control module

location you

would like to

erase

module location.

–14–

–43–

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (ML-100A Only)

HOME AUTOMATION

Installing Door / Window Sensors

Control Module [1] is represented by zone LED 1

Window / Door Sensor is used to monitor doors or windows that

open and close. When these doors / windows are open or

closed, the sensors will transmit a signal to the control panel

to notify the user. These sensors consist of 2 parts, one is the

transmitter, the other is the magnet.

This row

Buttons for

Learning Control Module

Transmitter

Magnet

Before installing the sensor, remove the battery isolator by pulling out the yellow

tab. Once the isolator is removed, the corresponding zone LED on the control

panel will flash and buzzer will beep. If the magnetic contact is closed, the

beeping will stop.

Note:

- Both Window/Door Sensors have been programmed at the factory. They are

Zone 1 Sensor 1 and Zone 2 Sensor 1. Trigger the sensor and listen to the

beeping and zone LED to determine which one is zone 1 and which is zone 2.

Part 2 Learn signal from Control Panel to Control Module

Step

Keys

Function

Enter

Programming

mode

Description

Note

Press and hold

the learn button

on the Control

Module until its

LED starts to

flash.

LED on the Control Module

will flash indicating it is in

learn mode.

Mounting the Sensor

The transmitters should be mounted on the door frame or window frame by

double sided tape. The magnet should be mounted on the door or window by

either double sided tape or screws. Make sure the magnet is aligned with the

red marking on the transmitter. If the surface of the frame is flat enough, double-

sided foam tape is sufficient, otherwise, it is recommended to screw the

mounting plate to the frame, then apply double sided tape. After mounting the

sensor, if the AAA+ logo is inverted, remove the front cover and rotate it so the

AAA+ logo is in the upright position.

After [X] is entered, you

will hear [Device X On]

indicating you have trans-

mitted an ON signal for

device X, where X is the

Control Module Location.

The LED on the Control

Module should be off,

indicating it has learned

the signal, you may now

release the learn button

and the LED will stay on

again.

[6] to [0]

Transmit an ON Refer to the

signal for the chart below to

selected device determine which

from the Control button [6] to [0]

Panel to the

Control Module. You should

transmit the “ON”

to press.

command for the

selected device.

Double-sided

foam tape

Magnet on the right

Mounting plate

and screws

(optional)

Sensor

Magnet on the left

CONTROL MODULE

LOCATION

TRANSMIT

BUTTON [X]

Testing:

After mounting the sensor, test the sensor by opening and closing the door or

window. Open the door or window will result in the followng:

1. Beeping - The number of beep represents the zone number.

2. Zone LED flashing - Number of flash represents the sensor number.

–42–

–15–

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION (ML-100A Only)

HOME AUTOMATION

Part 1 Learn signal from Control Module to Control Panel

2 Single flash

Step

Keys

Function

Description

Note

[PROG]

[MPIN]

3 beeps for valid

password. 1 long beep

for invalid password.

Enter Program- Enter master

ming mode

password to

programming

mode

1. Beep___Beep___

Beep___Beep___

............

[4]

Select learn

control module

programming

After [4] is entered, some

zone LEDs will flash or

stay off. The zone LEDs

represent whether that

zone is already occupied

by another control

Note:

- Try to mount the sensors as far away from the floor as possible to avoid

damaging them. Mounting the sensors at a higher position will also result in

better operating range.

module.**See Table E.

[1] to [5]

Select the

location [1], [2],

[3], [4], or [5].

Select control

module location

(Max. 5 control

modules)

After you have selected

the control module location,

that zone LED will be on.

- Do not mount the sensor to the exterior of the door / window, always mount the

sensor to the interior side of the door / window to avoid being damaged or

stolen by non-intended users.

Once the signal

is transmitted to

the Control Panel,

that signal will be

stored.

You will hear

Activate the

control module

by pressing its

learn button

Send signal

from control

module to

[Device X Accepted],

where “X” is the control

module location.

Installing Motion Sensor

The motion sensor is most suitable for guarding a large area such as living room,

family room, or bedroom. It can also be used to monitor a hallway or stairway.

control panel.

once quickly.

Insert Battery

ZONE LED

DESCRIPTION

Undo the screw on the back of the motion sensor and

remove the battery cover. Connect a 9V alkaline battery

to the battery connector. Please note the polarity.

Off

Zone is not occupied by any control module

Flashes once

This zone is occupied by another control module. Programming

another remote to this zone will overwrite the previous control

module.

If you are planning to install the motion sensor outdoor,

you should reduce the sensitivity by placing the jumper

at location “2”.

For indoor application, if you want to reduce the

sensitivity, you can change the jumper setting to

“2” as well.

Flashes twice

This zone is occupied by a remote. You can still program a control

module to this zone, and it will not overwrite the remote you have

in this zone.

Sensitivity

Flashes once,

then twice

This zone is occupied by a remote AND a controlmodule. If you

program another control module to this zone, it will overwrite the

previous control module, but not the remote.

Jumper Location 1 High Sensitivity

Jumper Location 2 Low Sensitivity

Caution:

** Table E: Zone LED status for learning control module.

Depending on the environment, if you experience a false trigger when the motion

sensor is placed outdoors, you should relocate it or even place it indoors. Wind

blowing at a tree, or direct sunshine could cause a false trigger. Therefore, if the

location at where the motion sensor is mounted could cause a false trigger, you

should change the mounting location for such sensor.

–16–

–41–

Download from Www.Somanuals.com. All Manuals Search And Download.

HOME AUTOMATION

INSTALLATION (ML-100A Only)

The Control Panel can be used to control lights and home applicances with a

Control Module, (Control Module is sold separately). Garage door opener can be

controlled with a Garage Door Receiver (sold separately). The Control Panel can

control up to 5 Control Modules / Garage Door Receivers.

For outdoor monitoring, please refer to page 33 to program the motion sensor

to Alert Zone.

You may now close the battery cover and

re-insert the screw.

Mount the ball-head joint on the wall with

screws provided. Slide the back of the

sensor into the ball-head joint. The

mounting angle can be adjusted.

There are 3 ways to control these modules / receivers:

1. Using the keypad on the control panel to

operate these modules / receivers manually

Testing

Walk test should be performed after the motion sensor is

mounted. Walk in the detected area, if motion is detected, a

red light inside the sensor will glow. If the red light does not

glow, motion has not been detected and you may need to

re-position the sensor. Ensure you walk test all the locations

that you would like the motion sensor to cover.

2. Calling in away from home using a touch tone

phone (Refer to “Remote Operation by Telephone”)

Door open

Lights

3. Setting up Event Trigger

Note:

DETECTING AREA: (Unit = meter)

(Refer to Advanced Programming)

1.2M

- Perform the walk test after you have inserted the

battery for more than 1 minute.

55°

11°

- Before performing the walk test, the sensor should

not detect any motion.

- After motion is detected once, the sensor will not

be triggered unless no motion is detected for 20

seconds. Therefore, wait for at least 20 seconds

during walk testing between 2 activations.

27°

22°

These control modules should be programmed to the control panel as device

1 to 5. Please follow the programming instructions below to program these

control modules.

12°

SENSOR

10 11 12 13

Learn Control Modules

Caution:

When installing the motion sensor, avoid placing it near heat or cold producing

devices (i.e. A/C or furnace vents, fans, ovens, space heaters, etc). Air movement,

especially caused by changes in temperature may trigger the Motion Sensor and

cause false alarms. Please carefully test your Motion Sensor so that it will only be

triggered by wanted movement.

Both control panel and control module are transceivers, meaning they can transmit

and receive signals from each other. For home automation, the user will initiate an

action from the control panel, such as sending a signal to turn on the light, then the

control module will receive such signal and respond. The control module will then

send back a confirmation to the control panel

to indicate the light has been turned on.

(command

Turn on

You have now successfully installed and programmed the Control Panel and its

sensors. Please follow the rest of the instructions for operations and advanced

programming.

signal)

Therefore, during programming,

Control

Module

it is required to program 2 things:

PWR

ARM

1. Signal from control module to

control panel (confirmation signal)

PROG

BATT

ARM

STAT

MUTE

Control

Panel

2. Signal from control panel to

control module (command signal)

Confirm on

(confirmation

signal)

–40–

–17–

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED PROGRAMMING

OPERATION

The Control Panel is always in one of the 2 operating modes:

1. Alert Mode - When the system is not armed (ARM LED off), it is in alert mode.

2. Alarm Mode - When the system is armed (ARM LED on), it is in alarm mode.

This row

Buttons for

Sensor 1

SENSOR 1 SENSOR 2

Button [1] Button [6]

Zone 1

Zone 2 Button [2] Button [7]

Zone LED :

Flash once

Alert Mode

Button [8]

Button [9]

Button [0]

Button [3]

Button [4]

Button [5]

Zone 3

Zone 4

Zone 5

The Control Panel will be in alert mode automatically if the system is not armed.

Alert mode allows users inside the premises to know what sensor is triggered.

It is intended to be used when someone stays inside the premises.

This row

Buttons for

Sensor 2

In alert mode, the control panel will give you notification of the triggered sensor(s)

by voice announcement, unique beeping and LED flashing.

Zone LED :

Flash twice

Number of beeps

Zone of the triggered sensor

Number of flashes of zone LED Sensor number of the triggered sensor

Erase Sensors

Note:

- Each zone can program up to 2 sensors. There are 5 zones, so up to 10 sensors

can be programmed to the control panel. Please refer to page 37, "Sensor

Location Selection Guide" for detail information.

Proceed to the following to erase a sensor.

Step

Keys

Function

Enter

Programming password to

Description

Note

Enter master

[PROG]

[MPIN]

3 beeps for valid password.

1 long beep for invalid

programming mode

password.

Alert Mode Examples (Door/Window sensor sold separately)

mode

Zone 1 Sensor 1

2. Single flash

Beep___Beep___

Beep___Beep .....

Select erase

remote

programming

[9]

After [9] is entered, some

zone LEDs will flash or

stay off. The zone LEDs

represent whether that zone

is occupied by any sensor.

**See Table D below.

Select the

Refer to the table

To erase an

occupied

sensor, press

[1] to [0].

After you have selected the

sensor, you will hear 3 beeps

and verbal confirmation

[Zone X Sensor Y Empty

Memory], where X and Y

are the zone and sensor

numbers you have selected.

sensor you below to select the

would like to remote location.

erase

Zone 3 Sensor 2 window

open

2. Double flash

Beep Beep Beep___

ZONE LED

Off

DESCRIPTION

Zone is not occupied by any sensor

This zone is occupied by sensor 1.

This zone is occupied by sensor 2.

Note:

-For Door / Window sensor, alert notification (beeping and LED flashing) will

continue until the sensor is in closed position, i.e. closing the window or door.

Flashes once

Flashes twice

-For motion sensor, the alert notification was disabled at the factory default. To

perform the walk test, it requires to enable the Alert Zone (Bypass Zone) feature

in the Control Panel. After the walk test, it needs to disable this alert zone feature

otherwise it will bypass the signal in the alarm mode. Please refer to the page 33,

"Alert Zone" for detail. Please refer to information.

Flashes once,

then twice

This zone is occupied by sensors 1 and 2.

** Table D: Zone LED status for erasing sensors.

–18–

–39–

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

ADVANCED PROGRAMMING

ZONE DEPENDENT FEATURES

SENSOR 1

Location

SENSOR 2

Location

Mute

Beep / Alarm

Auto Mute

Y / N

Event Trigger

Alert

Y / N

zone 1

zone 2

zone 3

zone 4

zone 5

Disabled / On / Off

When the alert beeping becomes undesired, you can terminate the beeping in 3

different ways:

Beep / Alarm

Y / N

Disabled / On / Off

Y / N

1. Mute button - Manual mute by pressing the

mute button

Table C

4. Once you have filled out the table, it should look something like this.

Pressing the mute button will temporary

disable the beeping for all the activated

sensors. For example, if a window with a

window sensor will be open for a long period

of time, the continuous beeping may become

undesired. Pressing the mute button will

temporary disable the beeping for this

ZONE DEPENDENT FEATURES

SENSOR 1

Location

zone 1 Front Door

SENSOR 2

Location

Front Window

Beep / Alarm

Auto Mute

Y / N

Event Trigger

Disabled / On / Off

Alert

Y / N

Kitchen Motion

Back Door

zone 2

zone 3

Beep / Alarm

Y / N

zone 4 Backyard Motion

Basement Water Basement Motion

zone 5

Mute Button

sensor only, it will still beep if other sensors

You may refer to each column representing the zone dependent feature, to program

each zone with the selected feature. For example, Auto Mute feature is only enabled

for zone 3, when you are in the auto mute programming, you should enable this

feature for zone 3 only, the rest of the zones should have this feature disabled.

Repeat this step for all 4 zone dependent features during programming.

are triggered. This sensor will beep again

if this window is closed, and then opened.

Buzzer Mode Selector

2. Change the buzzer mode - Disable Beeping

5. You may now follow the procedure below "Learn Sensor Continue" to program

the sensor(s) to the desired zone(s).

The beeping can be disabled for all

zones by changing the buzzer mode

selector.

Learn Sensors - Continue

Step

Keys

Function

Description

Enter master

password to

Note

3 beeps for valid

password. 1 long beep

for invalid password.

- If the buzzer mode selector is at "I", beeping is enabled.

- If the buzzer mode selector is at "II", beeping is disabled.

Enter Program-

ming mode

[PROG]

[MPIN]

programming mode

After [3] is entered, some

zone LEDs will flash

Select learn

sensor

programming

[3]

If beeping is disabled, all sensor alert beeping will be disabled, however, the

voice announcement and LED flashing will still function.

once, or twice, some will

be off. The zone LEDs

represent whether that

zone is already occupied

by another sensor.

3. Enable Auto-Mute in Advanced Programming

If this feature is enabled for that zone, beeping will be terminated automatically

after 15 seconds . Refer to "Advanced Programming" - Auto Mute" on page 32

for more information on how to enable this feature.

**See Table D next page.

After you have

selected the zone, that

zone LED will be on.

[0] to [9]

Select sensor

location

Refer to the diagram

below to select the

sensor location, which

includes the zone and

sensor number.

Trigger sensor

You will hear [Zone X

Sensor Y Accepted],

where X and Y are the

zone and sensor numbers

you have selected.

Activate the

sensor you

would like to

program to

this zone.

Once the sensor is

activated, the signal

will be transmitted

to the Control Panel

which will be stored.

–38–

–19–

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

ADVANCED PROGRAMMING

Learn Sensors

System Status

The control panel continuously monitors the system status as well as all the

sensors status. It will monitor occurrences such as triggered sensors, low

battery sensors, malfunction sensors, or phone line failure etc.

You can program up to 10 sensors to the control panel. There are 5 zones on

the control panel, each zone can program up to 2 sensors. Before program-

ming a sensor, you must decide which sensor location (zone number and

sensor number) you would like to program the sensor to. It is strongly recom-

mended that you refer to “Sensor Location Selection Guide” before deciding

which sensor location you would like to program the new sensors to. Some

features you may need to consider are: 1) Beep/Alarm setting, 2) auto mute, 3)

alert zone , 4) event trigger. Explanation for each feature can be found in the

following pages in Advanced Programming:

In order to check the system status, user can press the “Status” button on the

control panel, voice announcement will be made regarding the system and

sensor status. When the “Status” button is pressed, you will be notified if any of

the following events is occurring:

- System armed or disarmed

- Any triggered sensors

- Any sensors with low battery warning

- Any sensors with failure warning

- Phone line failure

1. Beep/Alarm Setting - Page 29

2. Auto Mute - Page 32

3. Alert Zone - Page 33

4. Event Trigger - Page 45

Refer to page 23 for more details regarding system failures.

Sensor Location Selection Guide

You can program up to 10 sensors to the control panel. There are 5 zones and

maximum 2 sesnors per zone. The 4 features mentioned above are Zone

dependent features meaning both sensors in that zone will operate based on

the setting for that zone. So if you program 2 sensors into one zone, those 2

sensors will react in the same manner for those zone dependent features. For

example, if you enable the Auto-Mute feature for zone 1, both zone 1 sensor 1,

and zone 1 sensor 2 will have this feature enabled. It is not possible to enable a

zone dependent feature for sensor 1 only, but not sensor 2.

Arming the System

You should arm the system when you are the last person to leave the house. By

arming the system, the control panel will call the preprogrammed emergency

phone numbers and the siren will sound when break-in occurs.

Caution: Only arm the system when nobody is expected to be inside the premises.

When someone is expected to be within the premises, the system should not be

armed.

Therefore, the followings are some suggestions of how you should select the

sensor location.

To arm the system, follow the procedures below:

1. Check all the zone dependent features, and determine if you would like to

enable any one of them.

Exit delay 45 seconds

BeepBeep

45 seconds later

ARM LED on.

System

Armed

2. If you decide not to enable any zone dependent features and keep the

factory default setting, you can simply program the sensor to any sensor

location based on your own preference. Omit the following steps and

proceed to "Learn Sensor - Continue".

1. Press [Arm] on the control 2. Leave the premises 3. After 45 seconds.

panel or keychain remote. within 45 seconds.

System will be armed.

3. If you decide to enable some of the zone dependent features, check Table C

below. Circle the zone dependent feature selections. If there are features

that you would like to enable for more than 2 sensors, you need to select

more than one zone for those features.

1. Press [Arm] button on the control panel when no sensors are triggered.

You can also use the keychain remote to arm the system by pressing arm

button on the remote.

–20–

–37–

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED PROGRAMMING

OPERATION

Remote [6] is represented by zone LED 1

Note:

- The control panel cannot be armed if there are triggered sensors. Make sure

all sensors are in closed position, i.e. (close all doors, windows, no movement

should be detected etc).

- The control panel can be armed if there are sensors with low battery or failure

warning.

REMOTE LOCATION

ZONE LED

2. After pressing the “ARM” button, the “ARM” LED will flash and you will have 45

seconds to leave the premises, this is called the exit delay. You will hear

beeping during the exit delay interval. The beeping rate will change from slow

to fast, the faster the beep rate, the less time you have left to leave the premises

before the siren sounds.

Erase Keychain / Keypad Remotes

3. When the exit delay expires, the control panel will announce “System Armed”,

beeping will stop and the ARM LED will be on steadily. This indicates the

system is now armed.

Follow the instructions below to erase keychain or keypad remotes / receivers.

Step

Keys

Function

Description

Note

[PROG]

[MPIN]

Enter master

password to pro-

gramming mode

3 beeps for valid

password. 1 long beep

for invalid password.

Enter

Programming

mode

Note:

The control panel can also be armed remotely when nobody is home, with a touch

tone phone. Please refer to “Remote Operation by Telephone” on page 27.

Select erase

remote

After [0] is entered, some

zone LEDs will flash or stay

off. The zone LEDs

represent whether that zone

is occupied by any remote.

** See Table B below.

[0]

programming

Disarming the system

If a sensor is triggered while the control panel is armed, such as entering a house

with an armed control panel, an entry delay will be triggered. User is allowed to

disarm the control panel during the 30-second entry delay. If the control panel is

not disarmed within 30 seconds, siren will sound immediately and emergency

calls will be made. To disarm the control panel, follow the instructions below.

After you have selected the

remote location, you will hear 3

beeps and verbal confirmation

[Device X Empty Memory],

where X is the remote location

you have selected.

Select a remote

location [6], [7],

[8], [9] or [0].

Select remote

location you

would like to

erase

To erase

an occupied

remote, press

[6] to [0].

Entry delay 30 seconds

BeepBeep

Arm LED off

System

Arm LED flashes

BeepBeep

ZONE LED

Off

DESCRIPTION

Zone is not occupied by any remote

Disarmed

Flashes twice

This zone is occupied by a remote. You may select this zone to

erase this remote.

Flashes once

This zone is occupied by a control module (Optional).

THIS IS NOTAREMOTE CONTROL, THEREFORE, SHOULD NOTBE

ERASED. (Refer to page 43 Erase Control Module for more

information)

3. Once the system is

disarmed, the Arm

LED will be off.

1.Entering the premises

will trigger the entry

delay.

2.Enter password within

30 seconds or press the

disarm button on the

keychain remote.

Flashes once,

then twice

This zone is occupied by a remote AND a control module.

You may select this zone to erase the remote.

1. During the entry delay, the system will beep for 30 seconds, the ARM LED will

flash during this entry delay interval. The faster the beep, the less time you

have left to disarm the control panel before the siren sounds.

** Table B: Zone LED status for erasing keychain/keypad remote(s).

* Please refer to erase control module on page 43.

–36–

–21–

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED PROGRAMMING

OPERATION

2. You must enter a valid password, either the Master Password, or Secondary

Password to disarm the system before entry delay expires.

Learn Keychain / Keypad Remotes

Additional keychain or keypad remotes can be programmed to the control panel.

Maximum of 5 keychain/keypad remotes can be programmed to the control panel.

3. When a valid password is entered, you will hear “System Disarmed” and the

entry delay beeping will stop, the ARM LED will be off.

- Keychain or keypad remotes should be programmed to Device 6 to Device 0.

Note:

- The control panel can also be disarmed remotely when nobody is home, with a

touch tone phone. Please refer to “Remote Operation by Telephone” on page 27.

Follow the instructions below to program remote(s) to remote location(s) 6, 7, 8,

9, or 0, which is the bottom row of the numeric keypad of the control panel.

Step

Keys

Function

Description

Note

- If 3 consecutive incorrect passwords are entered, alarm will sound immediately,

the control panel will be in panic mode, and start calling the emergency phone

numbers.

3 beeps for valid

password. 1 long beep

for invalid password.

Enter master

password to

programming mode

Enter Program-

ming mode

[PROG]

[MPIN]

Select learn

remote

programming

After [4] is entered, some

zone LEDs will flash or

stay off. The zone LEDs

represent whether that

zone is already occupied

by another remote.

[4]

Disarming a triggered control panel

If "System Panic" is announced from the control panel after it has been disarmed,

that means the alarm was triggered when it was in armed mode. Follow the

procedures below to set the control panel back to standby mode.

** See Table A below.

Select remote Select a remote

location

location [6], [7],

(Max. 5 remotes) [8], [9] or [0].

After you have selected

the remote location, that

zone LED will be on.

[6] to [0]

1. If the alarm was caused by sensor(s), there will be flashing LEDs and

beeping indicating which sensor(s) triggered the alarm. You may want to

check the condition of the triggered sensor(s), the sensor(s) may be damaged

if there were break-ins.

2. You need to reset the sensor manually by triggering it twice, i.e. open and

then close a door / window sensor, or walk in front of the motion sensor. The

LED representing that sensor will stop flashing after it receives the signal

from the sensor.

Trigger remote

Once the signal is

transmitted to the

Control Panel, that

signal which will

be stored.

Activate the

remote by

pressing any

one of the

buttons.

You will hear

[Device X Accepted],

where “X” is the remote

location.

3. You must now enter the password again on the control panel or press the

disarm button on the keychain remote, as an acknowledgement of the alarm

event. This will set the control panel back to standby mode.

ZONE LED

Off

DESCRIPTION

Zone is not occupied by any remote

Flashes twice

This zone is occupied by another remote. Programming another

remote to this zone will overwrite the previous remote.

Disarming under Duress

Flashes once

This zone is occupied by a control module* (Optional).

You can still program a remote to this zone, and it will not overwrite

the control module* you have in this zone. (Refer to page 40 Home

Automation for more information)

If you are forcibly compelled to disarm the control panel, you may enter the Duress

Password. Entering the duress password will terminate the entry delay, i.e. no

more entry delay beeping. But the control panel will silently call the emergency

phone numbers for help. The called party will hear the voice announcement

“System Panic”.

Flashes once,

then twice

This zone is occupied by a remote AND a control module*.

If you program another remote to this zone, it will overwrite the

previous remote, but not the control module*.

Note:

- The default duress password is [3838].

** Table A: Zone LED status for learning keychain/keypad remote(s).

* Please refer to learn control module on page 40.

–22–

–35–

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED PROGRAMMING

OPERATION

Panic

To enable alert zone feature, follow the instructions below.

Pressing the panic button on the control

panel or keychain remote will cause the

siren to sound and outgoing calls will

be made to the preprogrammed phone

numbers, “System Panic” will also be

announced. This can be used in any

emergency situation.

Step

Keys

Function

Description

Note

[PROG]

[MPIN]

Enter Program- Enter master

ming mode

3 beeps for valid

password. 1 long beep

for invalid password.

password to

programming mode

After [8] is entered,

some zone LEDs will

flash or stay on. This

indicates whether alert

zone is selected.

Select Alert

Zone.

[8]

To stop the siren and disarm the system, user can enter a valid password, or

press the disarm button on the keychain remote. This will terminate the siren

and the control panel from calling the rest of the emergency phone numbers.

Disable

Alert Zone: zone you

[1] to [5]

Select which

Refer to the

diagram below to that zone LED will be on.

select the

appropriate

setting.

If alert zone is selected,

would like to

select as Alert

Zone.

If it is not selected, the

LED will flash. You are

allow to make multiple

changes before terminat-

ing programming mode.

Enable

Alert Zone:

[6] to [0].

ARM

DISARM

PANIC

AUX

Terminate

programming

mode.

[PROG]

when

finished.

PROG LED will be

off.

- Control other Skylink receiver

such as Garage Door Receiver

System Failure

Control Panel constantly monitors itself and its sensors. If there are any trouble

conditions, the control panel will advise the user. These trouble conditions include:

DISABLE

ALERT ZONE ALERT ZONE

ENABLE

This row

Buttons to

Disable Alert Zone

Button [6]

Button [7]

Button [8]

Button [9]

Button [0]

Zone 1 Button [1]

- Phone Line Failure

Zone 2

Button [2]

Zone LED : Flash

- Sensor Failure (loss of supervisory signal)

- Low Battery – Control Panel

- Low Battery – Sensors

Zone 3 Button [3]

Zone 4

Button [4]

This row

Buttons to

Zone 5

Button [5]

Enable Alert Zone

Phone Line Failure

Zone LED : ON

When the phone line is disconnected or malfunctions, the control panel will

instantly notify the user by:

1. Both Power [PWR] and Program [PROG] LEDs will flash together;

2. Voice announcement “Phone Line Failure” will be played.

When phone line failure occurs, please check the phone line connection, ensure

the phone line is plugged into both the control panel and the wall socket securely.

You should also check the phone line with a normal telephone to determine if it

can dial out to a phone number. If it cannot dial out, that indicates the phone line

is not in service, you should contact your local phone company.

–34–

–23–

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

ADVANCED PROGRAMMING

Sensor Failure

The control panel constantly monitors its sensors, if the control panel fails to

communicate with any sensors, it will notify the user by:

ENABLE

AUTO MUTE

DISABLE

AUTO MUTE

This row

Buttons to

Disable Auto Mute

Zone 1

Zone 2

Button [6]

Button [1]

1. The zone LED of the failed sensor will be on steadily;

2. Voice announcement “zone X sensor Y failure” will be played.

Zone LED : Flash

Button [2] Button [7]

Zone 3

Zone 4

Zone 5

Button [8]

Button [9]

Button [0]

Button [3]

Button [4]

Button [5]

When sensor failure occurs, try the following:

This row

Buttons to

Enable Auto Mute

1. Check if the sensor is located at where it should be, and whether there is any

physical damage to the sensor.

Zone LED : ON

2. If the failed sensor is not physically damaged, try to activate the sensor and see

if the control panel reacts to such activation.

3. If not, try to remove the sensor from its location, and bring it closer to control

panel and activate the sensor. It is possible that the sensor is installed too far

from the control panel and it cannot establish a steady communication with the

control panel. If this is the case, please install the sensor closer to the control

panel.

Alert Zone (Bypass Zone)

As explained earlier, the control panel can operate in 2 different modes, 1) Alert

Mode, 2) Alarm Mode. In alarm mode, when a sensor is triggered, the control

panel will either give a 30 seconds entry delay, or siren will sound immediately

(with instant alarm). However, there are sensors that you do not want to trigger

the alarm when the system is armed. Such as an outdoor sensor, or any other

sensors that you only want to give you alert notification. Under such circum-

stances, zone(s) can be programed to react only when the control panel is in

alert mode, these zones will be automatically bypassed when the control panel

is in alarm mode. These zones can also be considered as "Bypass zones".

Low Battery

Control Panel

The control panel is powered mainly by the adapter. However, during power outage,

it will be powered by the rechargeable backup battery. Under standby conditions,

these batteries can last for 48 hours.

It is recommend to enable alert zone if:

When the backup battery is running low, the “LO BATT” LED on the control panel

will be on, indicating the backup battery should be recharged. To recharge the

backup battery, plug in the power adapter. It takes approx. 20 hours to fully charge

the backup battery.

- You do not consider the sensors in that zone an emergency

- Sensors in that zone are located outdoors

- When nobody is at home, you do not want to know the status of the sensor(s) in

that zone

Sensors (For ML-100A Only)

Factory Default: This feature was disabled for all zones at the factory.

All of the sensors are battery powered. Depending on the operating condition

and environment, the battery life varies from 9 months to 2 years. 9V alkaline

battery is used for the motion sensor, the battery life is approximately 9 months.

Door / Window Sensor operates on a Lithium CR-2032 battery, with battery life of

approximately 2 years. For other sensors, please refer to the user’s instructions

regarding the battery life.

–24–

–33–

Download from Www.Somanuals.com. All Manuals Search And Download.

OPERATION

ADVANCED PROGRAMMING

When the sensor is running low in battery, the sensor will send a wireless low

battery signal to the control panel. The zone LED representing that sensor will be

on steadily, indicating sensor(s) in that zone is in trouble condition. Control Panel

will also have an announcement to advise the user the trouble condition is low

battery, such as “zone X sensor Y low battery”, where X and Y represent the zone

and sensor number. Please replace the battery of that sensor.

Auto Mute

When a sensor is triggered in alert mode, audio warning will be emitted, either

beep or alarm. For example, if a door is opened, the beep will not stop until the

door is closed. If the door is open for 2 hours, the beep will go on for 2 hours.

There are times that this is not desired. With the auto mute feature enabled, the

beep will go on for only 20 seconds. After that, even if the sensor remains open,

the beep will stop only the zone LED will flash to indicate the sensor is triggered.

Beep will go on again if the sensor is closed and opened again.

Keychain Remote (For ML-100A Only)

The battery of the keychain remote (Alkaline, Type 23A, 12V) needs to be replaced

when either one of the followings occurs:

Note: Auto Mute only functions when the control panel is in alert mode (disarmed).

If the control panel is in alarm mode (armed), a triggered sensor will result in

entry delay or instant alarm.

1. The LED on the keychain doesn’t flash or on when a key is pressed; or

2. The operating range starts to decrease.

Factory Default: This feature was disabled for all zones at the factory.

To replace the battery:

To enable auto mute feature, follow the instructions below.

1. Undo the two screws on the back of the transmitter.

The bottom case will then come off.

2. Using a small screwdriver or pen, pry out the old

battery from one end.

Step

Keys

Function

Description

Note

[PROG]

[MPIN]

Enter Program-

ming mode

Enter master

password to

3 beeps for valid

password. 1 long beep

3. Place the new battery in position. A diagram in the

battery compartment indicates which end is positive

and which is negative.

programming mode for invalid password.

Select Auto Mute

Enable / Disable

After [6] is entered, some

zone LEDs will flash or

stay on. This indicates

whether Auto Mute is

enabled or disabled.

[6]

4. Close the battery cover and reinsert two screws.

If auto mute is enabled,

that zone LED will be on.

If it is disabled, the LED

will flash. You are allow

to make multiple changes

before terminating

Disable

Select which

Refer to the diagram

Auto Mute: zone you would below to select the

[1] to [5]

like to enable /

disable auto mute.

appropriate setting.

Enable

Auto Mute:

[6] to [0].

programming mode.

Terminate

programming

mode.

PROG LED will be off, and

you will hear 3 beeps.

[PROG]

when

finished.

–32–

–25–

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMUNICATION

ADVANCED PROGRAMMING

Receiving the Emergency Call

Follow the procedures below to program the beep / alarm setting.

If you are on the list as one of the recipients of the emergency call, you should read

the following instructions carefully. You should also notify all the persons you will

be calling so they know how to react when they receive the emergency call.

Step

Keys

Function

Description

Enter master

password to

Note

[PROG]

[MPIN]

EnterProgramming

mode

3 beeps for valid password.

1 long beep for invalid

programming mode password.

The control panel will call you when there are emergencies such as break-ins,

smoke, fire events, or someone at home needs assistance.

Select Beep /

Alarm Setting

After [5] is entered, some zone

[5]

LEDs will flash or stay on.

This indicates whether that

zone is set to beep or alarm.

1. When the phone rings at the calling location, the person who answers the

phone will hear a message related to the emergency events, such as

“System Panic”, or “Zone 1 Sensor 1 Triggered” etc. This message may be

repeated several times depending on how it was programmed.

Select which

Refer to the

zone you would diagram below to

Set to Beep:

[1] to [5]

If Alarm is set for that zone,

that zone LED will be on. If

Beep is set, the LED will

flash. You are allowed to

make multiple changes before

terminating programming

mode.

like to Beep or

Alarm.

select the appro-

priate setting.

Set toAlarm:

[6] to [0].

2. After the message has been repeated for

a certain number of times, the control panel

will ask for a valid password, you will hear

“Enter Password”.

PROG LED will be off, and

you will hear 3 beeps.

Terminate pro-

gramming mode.

[PROG] when

finished.

Zone 1

Sensor 1

Triggered

BEEP

ALARM

3. Enter the 4-digit password to have access

This row

Button [1] Button [6]

Zone 1

to the control panel. If a valid password is

accepted, you will hear “Password Accepted”,

otherwise, you will hear “Password Failure”.

Buttons for Beep

Zone 2 Button [2] Button [7]

Zone LED : Flash

Button [8]

Button [9]

Button [0]

Button [3]

Button [4]

Button [5]

Zone 3

Zone 4

Zone 5

Enter

Password

This row

Buttons for Alarm

4. After entering the correct password, you

can follow the “Phone Command” instruc-

tions to perform the required tasks, such

Zone LED : ON

as disarm, turn on / off devices or check the

-Arm

system status etc. For further information

-Disarm

-Check status

of how to control the system remotely,

-Control lighting etc.

Example:

please refer to the next section, "Remote

-Disconnect

If you would like to change the setting for zone 5 from “Beep” to “Alarm”, simply

Operation by Telephone".

press [0] at step 3.

This will change the zone 5 setting to “Alarm”.

–26–

–31–

Download from Www.Somanuals.com. All Manuals Search And Download.

ADVANCED PROGRAMMING

COMMUNICATION

Remote Operation by Telephone

System Armed (Alarm Mode)

If a zone is set to “Beep”, the control panel will give entry / exit delay.

If a zone is set to “Alarm”, the siren will sound immediately without entry delay

The control panel can be operated while you are away from home. You can

have access to the control panel with any touch tone phone to perform a variety

of operations, listed below.

- Alarm Mode (System Armed): If a sensor is triggered (i.e. opening a door) with

the alarm setting on, the siren will sound immediately without entry delay, it is

called “Instant Alarm”. The siren will not stop until the siren timeout or a valid

password is entered. Control panel will call the emergency phone numbers to

notify the users of the alarm situation.

- Arm

- Disarm

- Lights, Home Applicances on / off (Requires additonal Control Module)

- Garage door open / close (Requires additional Garage Door Receiver)

- System status

- Disconnect

When a sensor is triggered, there are 4 options:

ZONE SETTING

There are 2 ways you can have access to the remote phone operation:

OPERATING MODE

Disarmed (Alert)

Armed (Alarm)

BEEP

ALARM

1. You can call the control panel when you are away from home; or

2. When the control panel calls you during emergency.

1) Beep

2) Alarm sounds immediately

3) Entry / Exit Delay

4) Alarm sounds and calls

preprogrammed phone

numbers immediately

To access the control panel away from home

Calling in when you are away from home

Factory Default: All zones were programmed to Beep at the factory.

You may consider to programming the zone(s) into Alarm mode if:

1. Call your home phone number, or the number that the phone line of the control

panel is connected to.

2. Hang up after the second ring.

- You need immediate attention if that sensor is triggered, such as flood sensor,

smoke sensor etc.

- The sensor will not be triggered on a daily basis, such as a door that you

normally will not open, and if it opens, you would like to know immediately.

3. Wait at least 10 seconds, but not more than 40 seconds, then call the phone

number again.

4. The control panel will pick up the phone call and request for a valid user

password, you will hear “Enter Password”. You can enter either the Master

Password or Secondary Password. If the password is correct, you will hear

“Password Accepted”, otherwise, you will hear “Password Failure”.

Caution:

It is not recommended to program an outdoor sensor to Alarm mode, which may cause

false alarm. For outdoor sensors, they should be programmed into an Alert Zone,

please refer to page 33 for details.

5. Once the password is accepted, you can have access to all the operations

listed below.

–30–

–27–

Download from Www.Somanuals.com. All Manuals Search And Download.

COMMUNICATION

ADVANCED PROGRAMMING

Advanced Programming allows users to customize the control panel to react

differently under different conditions. Features such as:

Table 1: Remote Phone Operations

SYSTEM OPERATION

PHONE COMMAND

DESCRIPTION

- When a sensor is triggered, the control panel can beep or alarm

- Beeping can be terminated automatically after a fixed period of time for some sensors

- Some sensors can be programmed to beep only, never alarm

- When a door is open, turn lights on

Turn on device x

[x] = 1 to 5

x+[*]

Turn devices on will hear [Device X On]. When the

control module receives the on signal, it will turn on the

plugged in device, and send a confirmation back to the

control panel. You will then hear [Device On Accepted].

- Program additional sensors and remotes

x+[#]

Turn off device x

x = [1 to 5]

Turn devices off will hear [Device X Off]. When the

control module receives the off signal, it will turn off the

plugged in device, and send a confirmation back to the

control panel. You will then hear [Device Off Accepted].

Programming Summary

COMMAND

[PROG] + [1]

[PROG] + [2]

[PROG] + [3]

[PROG] + [4]

[PROG] + [5]

[PROG] + [6]

[PROG] + [7]

[PROG] + [8]

[PROG] + [9]

[PROG] + [0]

DESCRIPTION

Program Phone Numbers

Program Password

Check system status

Arm

You will hear system status announcement

You will hear [System Armed]

You will hear [System Disarmed]

Phone line disconnect

[8]+[#]

[7]+[#]

Learn Sensors

[9]+[#]

[0]+[#]

Disarm

Learn Keychain or Keypad Transmitters / Control Modules

Beep / Alarm Setting

Disconnect

Auto Mute Setting

Event Trigger Setting

Alert Zone (Bypass) Setting

Erase Sensors

Erase Keychain or Keypad Transmitters / Control Modules

Follow the instructions below to have access to Advanced Programming.

Beep / Alarm

User can customize the audio warning so that when a sensor is triggered, the

control panel may beep or alarm may sound instantly. Depending on whether the

control panel is armed or disarmed, the audio warning is different.

System Disarmed (Alert Mode)

If a zone is set to “Beep”, the control panel will beep when a sensor is triggered,

until the sensor is deactivated. Motion Sensor activation will not cause any

beeping unless the zone for the motion sensor is programmed as a "Bypass

Zone" (see page 33).

If a zone is set to “Alarm”, alarm will sound instantly when a sensor is triggered.

Alarm will stop when the sensor is deactivated, or reaches a 3-minute time out period.

–28–

–29–

Download from Www.Somanuals.com. All Manuals Search And Download.

Mountfield Lawn Mower MP84401 05 User Manual
Mr Coffee Coffee Grinder BM Series User Manual
NEC Computer Monitor XV17+ User Manual
NETGEAR Network Router EX6120 User Manual
Nortel Networks Cordless Telephone 4075 User Manual
Oki Printer C9000 Series User Manual
Oregon Scientific Radar Detector WR606 User Manual
OWI Portable Speaker LGS470 User Manual
Panasonic CRT Television CT 2707D CT 3207D User Manual
Panasonic Smoke Alarm 3378 User Manual