PROPANE PATIO HEATER
WARNING: For Outdoor Use Only.
FOR YOUR SAFETY
If you smell gas:
1. Shut off gas to the appliance.
OF
F
2. Extinguish any open flame.
3. if odor continues ,immediately
call gas supplier.
H
IG
H
FOR YOUR SAFETY
Do not store or use gasoline or
other flammable vapors or liquids
in the vicinity of this or any other
appliance.
CAUTION: Retain these instructions
for future use.
C E R T I F I E D
Model No.:SRPH02S
Master Contract No.:217109
Customer Item No.: PTH38PSS
PTH38PGM
PTH38PCP
Manual, Instructions & Parts List
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS
9
1
4
1
Center Reflector Cap
Reflector Cap
1
2
3
10
1
Head Assembly
1
1
1
Gas Hose
Post
4
5
6
7
2
Cylinder Cover
15
16
3
1
Post Mounts
Cylinder Base
8
15 M6 Nuts
9
3
18 6mm Washers
10
11
12
13
14
6
5
5mm Washers
4mm Washers
x
5
6
M4 8 Bolts
4
x
M5 8 Bolts
13
5
15
16
17
18
x
12 M6 10 Bolts
3
M6 x70 double pointed bolts
1
Regulator
1
Cylinder (Not Supplied)
6
9
10
11
12
14
13
14
15
7
17
16
17
8
3
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUTIONS
NOTE: PLEASE READ THE FOLLOWING SAFETY RULES
At least once a year, the unit should be inspected for the
presence of spiders, spider webs or other insects. Check the
heater immediately if any of the following exist:
WARNING
This appliance must only be used outdoors.
Using this product in an enclosed area may cause
injury, death or property damage.
1. The smell of gas in conjunction with extreme yellow
colored tips of the burner flames.
Read the instructions before use.
This appliance must be installed in
accordance with such regulations as
are in force.
2. The heater does not reach temperature.
3. The burner makes popping noise during use (a slight
popping noise is normal when the burner is extinguished
after using).
Do not use the heater in an explosive atmosphere.
Keep the heater away from areas where gasoline or other
flammable liquids or vapors are stored.
The propane hose with regulator assembly shall be located
out of pathways where people may trip over it or in areas
where the hose will not be subject to accidental damage.
Prior to use, check for damaged parts such as hoses,
regulators, pilot or burner.
The installation of fixed appliances shall only be carried out
by competent persons and be in accordance with the relevant
Codes of Practice.
Warning: This appliance requires a gas hose and regulator,
check with your gas supplier and or product supplier.
Regularly check the gas hose and if necessary,
replace the gas hose.
Children and adults should be aware of the hazards of high
surface temperature.
Young children should be carefully supervised when they
are in the area of the heater.
Clothing or other flammable material should not be hung
from the heater, or placed on or near the heater.
DISCONNECT LPG bottle before moving the heater.
Do not attempt to alter unit in any manner.
EXAMPLE: using the heater without the top canopy
reflector or radiant screen.
Any guard or other protective device removed for
servicing the heater must be replaced prior to
operating the heater.
Do not shorten the burner post assembly.
The appliance shall not be used in basements or below
ground level.
Installation and repair should be done by a qualified
service person. The heater should be inspected before
use and cleaning may be required at least once a year, or as
necessary. It is imperative that control compartment, burner
and circulating air passageways of the heater be kept clean.
It must always be placed on a solid and level surface.
For outdoor use ONLY.
Never replace or substitute the regulator with any regulator
other than the factory suggested replacement.
Keep the appliance area clear of combustible materials
such as gasoline and other flammable vapors and liquids.
Do not clean the heater with cleaners that are combustible
or corrosive.
Do not obstruct the flow of combustion and ventilation air.
Do not paint radiant screen, control panel or top canopy
reflector.
Keep the ventilation opening of the cylinder enclosure free
and clear of debris.
All leak tests should be done with a soapy solution. NEVER
USE AN OPEN FLAME TO CHECK FOR LEAKS.
The LP gas cylinder should be turned off when the
heater is not in use.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IGNITER BATTERY INSTALLATION
Instruction For Battery Installing
Remove igniter button by turning counter clockwise.
Install “AAA” battery with positive terminal up as indicated
in diagram. Replace igniter button.
Ignition button
Control knob
Replace Battery
Ignition button
AA battery
5
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
NOTE: Assembly of this heater requires
basic mechanical skills. Proper assembly
is the responsibility of the installer.
Step 1
5
Step 1 ---- Attach Post to Base Assembly
Attach the post to the post mounts using
M5 X 8 bolts (6 pcs) and 5mm washers (6 pcs)
14
11
7
Step 2 ---- Attach Cylinder Cover to Post Mounts
Step 2
Attach the cylinder cover to the post mounts by
sliding over post as indicated.
6
7
6
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
NOTE: Assembly of this heater requires
basic mechanical skills. Proper assembly
is the responsibility of the installer.
Step 3
Step 3 ---- Attach Head Assembly to Post
3
Load head assembly by inserting gas hose
into post.
Insert head assembly into post.
Tighten securely using M4 X 8 Bolts (5 pcs)
and 4mm washers (5 pcs).
4
13
12
5
Step 4
Step4 ----
Attach Double Threaded Bolts to
Head Assembly
10
Attach M6 X 70 double threaded bolts (3 pcs) and
6mm washers (3 pcs) to the top of head assembly
and tighten the bolts securely.
16
3
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
NOTE: Assembly of this heater requires
basic mechanical skills. Proper assembly
is the responsibility of the installer.
Step 5
9
10
1
Step 5 ---- Attach Center Reflector to Reflector
Attach center reflector to the top of reflector (4 pcs)
with M6 X 10 mm screws (12 pcs),
6mm washers (12 pcs) and nuts (12 pcs).
15
2
Step 6 ---- Attach Center Reflector and Reflector
to the top of Head Assembly
Step 6
9
Attach center reflector and reflector to the top
of head assembly by sliding over
M6 X 70 double threaded bolts (3 pcs).
Fasten with 6mm washers (3 pcs) and nuts (3 pcs).
10
3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
NOTE: Assembly of this heater requires
basic mechanical skills. Proper assembly
is the responsibility of the installer.
Step 7
Step 7 ---- Connect Gas Line to Cylinder
Attach Gas hose to regulator with 3/8 inch open end
wrench and adjustable wrench.
Attach regulator to cylinder. Tighten securely.
Move cylinder to the plate of base assembly.
Step 8
Step 8 ----
Check for leaks
Your Patio Heater has been checked at all
factory connections for leaks. To check the
connection of the gas hose/regulator/cylinder:
1) Make leak solution by mixing 1 part liquid
dish soap and 3 parts water.
2) Brush several drops (or use spray bottle)
of the solution onto the gas hose/regulator and
regulator/cylinder connection.
3) Turn on gas. Inspect the connections and look
for bubbles.
4) If no bubbles appear, the connection is safe.
5) If bubbles appear, there is a leak, loosen and
re-tighten this connection.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Step 9---- Lower Cylinder Cover onto
Cylinder Base
Step 9
Lower the cylinder cover onto the cylinder base .
6
8
Step 10---- Disconnect Cylinder
When Storing or Transporting
Step 10
1) Turn off the heater.
2) Raise the cylinder cover onto the post mounts.
3) Turn off the valve on the cylinder.
4) Disconnect the regulator from the cylinder.
6
7
10
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
DO NOT attempt to operate heater until you have
WARNING:
WARNING
read and understand all precautions. Failure to do so can
result in serious personal injury, death or property damage.
FOR YOUR SAFETY:
If at any time you are unable to light
burner and smell gas, wait 5 minutes to
allow gas to dissipate before attempting
to light heater.
Before Turning Gas Supply ON
Your heater was designed and approved for OUTDOOR USE ONLY. DO NOT use it inside a
building, or any other enclosed area. Make sure surrounding areas are free of combustible
materials, gasoline and other flammable vapors or liquids. Ensure that there is no
obstruction to air ventilation. Be sure all gas connections are tight and there are no leaks.
Be sure the access panel is clear of debris. Be sure any component removed during
assembly or servicing is replaced and fastened prior to starting.
If after 1 minute you are unable to light
burner, wait 5 minutes and allow
flammable vapors to dissipate before
attempting to light heater again.
Before Lighting
Heater should be thoroughly inspected before each use, and by a qualified service person
at least annually. If relighting, always wait at least 5 minutes.
This heater is tested for quality assurance. Ignition attempts should succeed 8 out
of 10 attempts.
WARNING
FOR YOUR SAFETY:
DO NOT touch or move heater for at least
45 minutes after use.
LIGHTING INSTRUCTIONS
Allow emitter and dome to cool before
touching.
1. Push and turn the control knob clockwise to the off position.
2. Fully open the propane tank valve or natural gas supply valve.
3. Push and turn the control knob counter-clockwise to the pilot position. Depress the control knob.
Push and hold the igniter button until the pilot lights.
4. Once the pilot lights, release the igniter button and continue to depress the control knob for
30 seconds.
5. After depressing the control knob for 30 seconds, release the control knob and turn it
counter-clockwise to the low or high position.
Note: If the pilot light will not ignite, turn the control knob to the off position, and fully close the
propane tank valve or natural gas supply valve. Wait 5 minutes and then repeat steps 2-4.
Alternately, the pilot can be lit using a wand lighter. Push and turn the control knob to the pilot
position. Depress the control knob. Insert the lit lighter through the ignition hole on the emitter
screen. Once the pilot lights, remove the lighter and continue to depress the control knob for
30 seconds.
Whenever the unit is disconnected from the natural gas supply, the supply lines fill with air. Expect
a delay in lighting the pilot, the first time the unit is lit after reconnecting.
INSTRUCTIONS D’ALLUMAGE
1. Poussez et tournez le bouton de réglage vers la droite à "off".
2. Ouvrez complètement la soupape du réservoir de propane ou de l'approvisionnement en
gaz naturel.
3. Poussez et tournez le bouton de réglage vers la gauche à "pilot". Appuyez sur le bouton
de réglage. enfoncez et maintenez l'allumeur jusqu'à ce que la veilleuse s'allume.
4. Une fois la veilleuse allumée, relâchez l'allumeur et continuez d'appuyer sur le bouton de
réglage pendant 30 secondes.
Emitter Screen
Ignition Hole
5. Après avoir appuyé sur le bouton de réglage pendant 30 secondes, relâchez le bouton de
réglage et tournez-le vers la gauche à "low" ou à "high".
Remarque : Si la veilleuse ne s'allume pas, tournez le bouton de réglage à "off" et fermez complètement la soupape du réservoir de propane ou de
l'approvisionnement en gaz naturel. Attendez 5 minutes et répétez les étapes 2 à 4. Comme autre alternative, la veilleuse peut être allumée à l'aide
d'un allumoir. poussez et tournez le bouton de réglage à "pilot". Appuyez sur le bouton de réglage. Insérez l'allumoir allumé dans l'orifice d'allumage
sur l'émetteur grillagé. Lorsque la veilleuse s'allume, retirez l'allumoir et continuez d'appuyer sur le bouton de réglage pendant 30 secondes.
lorsque l'appareil est débranché du réservoir de propane ou de l'approvisionnement en gaz naturel, les conduites d'alimentation se remplissent d'air.
Un délai sera nécessaire pour allumer la veilleuse la première fois que l'appareil sera allumé après avoir été rebranché.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
Note: The flame pattern at the emitter grid should be visually checked whenever the heater is
operated. Normally the burner flame is blue, but little yellow flame is acceptable.
If flames extend beyond the surface of the emitter grid, flame is lifting off the or there is a black
soot (carbon) accumulating on the emitter grid or reflector, the heater should be turned off
immediately. The heater should not be operated again until services and or replaced.
If you experience any ignition problem, turn off the heater and gas supply, and consult
“Troubleshooting" on page 15.
When lit for the first time the heater may emit a slight odor and smoke. This is a
normal temporary condition caused by the “burn in” of paints and lubricants
used in the manufacturing process and will not occur again. Simply run the
heater on “high” for 30 minutes.
The burner may be noisy when initially turned on. To eliminate excessive noise from the burner,
turn the Control Knob to the “LOW” position. Then turn the knob to the level of heat desired.
When heater is ON:
Emitter screen will become bright red due to intense heat. The color is more visible at night.
Burner will display tongues of blue flame. These flames should not be yellow or produce thick
black smoke, indicating an obstruction of airflow through the burners.
Operation Pressure Checked
If the flame is very small, this is because the supply pressure is not enough.
1) Turn the control knob to “OFF” position.
2) Wait five (5) minutes before attempting to relight pilot.
3) Repeat steps beginning with step 3 on page 11.
Never leave the heater unattended while in use.
Follow the Shut Down Instructions outlined below.
SHUT DOWN INSTRUCTIONS
1) Push in and turn control knob clockwise to "OFF" position.
2) Turn off the natural gas supply valve.
Note: After use, some discoloration of the emitter screen is normal.
FERMETURE
1) Poussez et tournez le bouton de réglage vers la droite à “OFF”
2) Fermez complétement la soupape de réservoir de propane ou de l’approvisionnement en gaz
naturel.
Note: After use, some discoloration of the emitter screen is normal.
The Event of Gas Leakage
1) Turn the control knob to “OFF” position.
2) Wait 5 minutes to allow gas to dissipate.
3) If odor continues, immediately call gas supplier.
Handle with extreme care.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
LOCATING HEATER FOR USE
BE CAREFUL: WHEN CERTAIN
MATERIALS OR ITEMS ARE Stored,
ABOVE, BESIDE OR UNDER THIS
HEATER WHILE IN USE, THEY WILL
BE SUBJECT TO RADIANT HEAT
AND COULD BE SERIOUSLY
DAMAGED.
36"
This heater is primarily used for the heating of
outdoor patios, decks, pool and spa areas.
Always make sure that adequate fresh air
ventilation is provided. Follow the spacing
tolerances shown in Figure 1.
24"
24"
The minimum clearances, shown in Figure 1, must
be maintained at all times.
The installation must conform to local codes, or in
the absence of local codes, with the standard for
the storage and handling of liquid petroleum gases,
ANSI/NFPA 58-1986, or most recent addition. For
Canada, with the current CAN1-B149.
Figure 1
This heater must be placed on firm level ground.
Never operate in an explosive atmosphere. Keep
away from areas where gasoline or other
flammable liquids or vapors are stored or used.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE/CLEANING/STORAGE
MAINTENANCE :
Visually check
To enjoy years of outstanding performance from your heater make
sure you perform the following maintenance activities on a regular
basis:
Keep exterior surfaces clean.
Emitter Screen
Use warm soapy water for cleaning. Never use flammable or
corrosive cleaning agents.
While washing your unit, be sure to keep the area around the
burner and pilot assembly dry at all times. If the gas control is
exposed to water in any way, DO NOT try to use it. It must be
replaced.
Yellow Tip
Primarily Blue Flame
Air flow must be unobstructed. Keep controls, burner and
circulating air passageways clean. Signs of possible blockage
include:
Gas odor with extreme yellow tipping of flame.
Heater does NOT reach the desired temperature.
Heater glow is excessively uneven.
Heater makes popping noises.
FOR YOUR SAFETY :
WARNING
DO NOT touch or move heater for at least 45 minutes after
use. Allow all burner elements to cool before touching.
Spiders and insects can nest in burner or orifices. This
dangerous condition can damage heater and render it unsafe for
use. Clean burner holes by using a heavy-duty pipe cleaner.
Compressed air may help clear away smaller particles.
NOTE: In a salt-air environment, such as near an ocean,
corrosion occurs more quickly than normal. Frequently
check for corroded areas and repair them promptly.
Carbon deposits may create a fire hazard. Clean dome and
emitter with warm soapy water if any carbon deposits develop.
CLEANING :
NOTE: Wait until heater is cool before covering.
1.Remove the reflector and emitter by removing the 4 screws
that fasten the emitter to the lower screen cone .
Any debris in the burner port should be cleared. Any rust can be
removed carefully with a wire brush. Never use a piece of wood,
or other materials that might break off and block the ports.
2.Remove lower cone cylinder by removing the 4 screws which
attach the lower cone cylinder to the control cylinder. Clear
debris on the surface of thermocouple.
STORAGE :
Between uses:
Turn the control knob to "OFF" position.
Turn LP cylinder to "OFF" position.
Store heater upright in an area sheltered from direct contact
with inclement weather (such as rain, sleet, hail, snow, dust
and debris).
3.Remove the 4 screws at the bottom of control cylinder. Clear
the debris of the surface and the inside of the injection nozzle.
If desired, cover heater to protect exterior surfaces and to
help prevent debris in air passages.
NOTE :
During periods of extended inactivity or when transporting:
It is recommended that the painted components from the emitter
down are periodically protected with a coat of automobile wax. If
repainting is necessary, paint only the post and gas cylinder
housing. Never paint the reflector, head assembly, or instruction
plate on post.
Turn the control knob to "OFF" position.
Disconnect LP Cylinder and move to a secure, well-ventilated
location outdoors. Do NOT store in a location that will exceed
125 degrees F.
The propane cylinder must be stored outdoors in well-ventilated
area, and it must be out of reach of children, and not in a building,
garage or any other enclosed area.
Keep exterior surfaces clean:
Use warm soapy water for cleaning. Never use flammable or
corrosive cleaning agents. While washing your unit, be sure to
keep the area around the combustion assembly dry at all times. If
the gas control is exposed to water in any way, DO NOT try to use it.
It must be replaced.
Store heater upright in an area sheltered from direct contact with
inclement weather (such as rain, sleet, hail, snow, dust and
debris). If desired, cover heater to protect exterior surfaces and
to help prevent debris in air passages.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
TROUBLESHOOTING
PROBLEM
PROBABLE CAUSE
SOLUTION
Pilot will not light
Gas valve may be OFF
Turn the gas valve ON
Fuel Tank empty
Orifice blocked
Refill LP gas tank
Clean or replace orifice
Purge air from lines, with knob
in pilot position, depress and
hold in, to release air.
Air in supply system
Loose connection
Dead battery
Check all fittings
Replace battery
Pilot will not stay on
Burner will not light
Debris around pilot
Loose connection
Thermocouple bad
Gas leak in line
Clean dirty area
Tighten connection
Replace thermocouple
Check connections
Lack of fuel pressure
Pressure is low
Fuel tank is near empty
Supply pressure is not enough
Remove, clean and replace
Turn valve to ON
Orifice blocked
Control valve not ON
Thermocouple is bad
Replace thermocouple
Pilot light assembly bent
or not in correct location
Place pilot in proper
position and retry
15
Download from Www.Somanuals.com. All Manuals Search And Download.
|