D50IR Manual 18-Mar-2010
2
9
SET DATE AND TIME
D50IR MODEL CAMERA
In SETUP mode, the LCD will show the time. Press ENTER and the
hour will ꢀash. Press Up( ) or Down( ) to select the proper hour,
then press ENTER again and the minute will ꢀash. Press Up( ) or
Down( ) to select the proper minute. Press ENTER again, AM or PM
will ꢀash. Press Up( ) or Down( ) to select the Day and Night
accordingly. Press ENTER to conꢁrm the selections.
8. POWER ON/OFF BUTTON
16. BATTERY COMPARTMENT
17. 12-VOLT EXTERNAL POWER
PORT
9. FUNCTION SWITCHES
• MODE (IR AIM, SETUP, AUTO)
• DELAY (1, 5 , 10, 30 MINS)
• RESOLUTION (VID, HI, LO)
(This camera is compatible
with the Moultrie Powerpanel
accessory to extend your
battery life. Please visit our
website at
10. STATUS INDICATOR
11. BATTERY INDICATOR
12. SELECT BUTTON
After setting up the time, press SELECT and the LCD will show the
year. Press ENTER and the year will ꢀash. Press Up( ) or Down
13. CHANGE BUTTONS
(
) to select the proper year and press ENTER again to conꢁrm.
(UP
14. ENTER BUTTON
15. SD MEMORY CARD SLOT
/DOWN
)
for more information
After setting up the year, press SELECT and the LCD will show the
date. Press ENTER and the month will ꢀash. Press Up( ) or Down
(
) to select the proper month, then press ENTER again and the day
will ꢀash. Press Up( ) or Down( ) to select the proper day, then
press ENTER again to conꢁrm.
9
8
Press
“SELECT”
10
11
AM
10:30
Time
2009
131
15
14
Year
Month & Date
13
12
EVENT DELAY
There are 4 different delay settings: 1 MIN., 5 MIN, 10 MIN. or 30
MIN.. Slide the DELAY SWITCH to the position of your selection.
When the game camera is in AUTO mode, it will work according to
your selected event delay.
16
17
IMAGE QUALITY AND VIDEO
There are 3 different capture settings: Video (VID), High (HI) and Low
(Lo). Please refer to the section 7 MEMORY – STORAGE/CAPCITY for
the description of each setting. Slide the RESOLUTION SWITCH to
the position of your selection. When the game camera is in AUTO
mode, it will work according to your selected capture setting.
NOTE: Product label is inside the carmera cover.
MFH-DGS-D50IR
4
7
1
10
ON/OFF button
Your camera supports external SD memory card ONLY (NO internal
memory available). The LCD shows “0000” if NO SD memory card
is inserted in AUTO mode. The camera cannot capture without
external memory.
Turn the unit ON or OFF. To turn ON you must press and hold the
ON/OFF button until the LCD display activates.
Unlock the two latches to open the camera cover.
Insert 4 fresh C Cell alkaline batteries into the battery compartment.
Place the batteries so the positive (+) and negative (-) polarities are
lined up correctly as indicated in the battery compartment.
Close the camera cover. When the battery indicator turns “Green”,
replace the batteries with fresh C cell alkaline batteries.
MODE SWITCH
Depending on the position of the switch,
there are 3 possible functions: IR AIM,
SETUP and AUTO.
Please inserts a SD memory card.
EVENT DELAY SWITCH
Depending on the position of the switch,
there are 4 event delay time can be set: 1
min, 5mins, 10mins and 30mins.
RESOLUTION SWITCH
Depending on the position of the switch, there is one video option:
VID and two images resolution options: HI and LO
UP( ) OR DOWN ( ) BUTTON
Used to change the settings within the
SETUP mode.
SELECT BUTTON
Make selections in SETUP mode.
D50IR MODEL CAMERA
ENTER BUTTON
Conꢁrm the selection in SETUP mode.
2
SD MEMORY CARD PORT
Insert SD card for memory with the metal
contact facing down. A SD card is required in order for the camera to
capture images/videos.
TURN POWER ON AND OFF
Open the camera cover. Slide the MODE switch to the SETUP
position. Press and hold the ON/OFF button until the time appear on
the LCD display. If you want to turn the unit off, simply press the
ON/OFF button again. The LCD shows “OFF” and then goes off.
NOTE: If there is no activity for 2 minutes, the camera will
automatically shut off to conserve battery life.
STATUS INDICATOR
To indicate a motion is detected in IR AIM
mode.
STATUS
BATTERY INDICATOR
BATTERY
-To indicate the batteries are low, please
replace batteries with fresh batteries.
6
3
4
8 CAMERA – SPECIFICATIONS
Operational Modes:
Auto – Automatic operation
Setup – Set Date and Time
IR Aim – Infra Red Aiming object
10 seconds AVI clips
SETUP MODE
INFRARED (IR) AIM
GENERAL OPERATION
To change digital camera settings, the MODE switch has to be in the
SETUP position.
The camera can be aimed using the
infrared detection system. Slide the
MODE switch to IR AIM position.
1. Automatic AUTO mode records images/videos using infrared
detection. ALWAYS LEAVE THE MODE SWITCH IN THE AUTO
MODE OR THE CAMERA WILL NOT OPERATE.
Video:
Picture Resolution (pixels):
LO/HI
AUTO MODE
Press and hold the ON/OFF button until
“Ir” is displayed on the LCD panel.
The IR aiming mode is now active.
Wave your hand in front of the camera.
The STATUS light will turn red every time
motion is detected. Find your desired target.
Note: The camera will shut down automatically after 2 minutes to save
battery life.
(See Section7, Memory • Storage / Capacity)
JPEG – still images and AVI – video clips
UP to 16GB (optional)
Turn the MODE switch to the AUTO position, press and hold the
ON/OFF button to switch on the camera. In the AUTO mode, the LCD
display shows the time(Fig1) and then counts down for 10 sec(Fig2).
The LCD goes off and the camera is STANDBY for capturing.
Format:
2. Setup SETUP mode for setting up Date and Time as described in
previous section.
Max. External SD Memory:
Infrared Sensor:
Infrared Sensor Range:
Flash:
Passive, activated when motion is detected
30 ft. / 22° width
3. IR Aim IR AIM mode for helping you to aim the camera towards
the object. Please consult the section 6. OPERTAION – AIMING
for detail description.
IR LEDs
If a motion is detected, the camera will wake up and show the
time(Fig3). While a picture or video clip is capturing, the LCD shows
“SNAP”. After the capturing process is ꢁnished, it will show the
number of pictures or video clips remain(Fig4). Then the camera will
be in STANDBY mode again.
Flash Range:
5 ft. - 30 ft.
Image Output:
Event Delay:
Record in SD card
1 MIN., 5 MIN, 10 MIN. or 30 MIN.
Displays Date/Time Setup and Images/
Videos Count
LCD Display Panel:
Power Supply:
Duty Cycle:
Adjustable mounting:
4 Alkaline C Cells batteries
30 days average with 4-C Cell batteries
Mounting Strap
Motion detected &
Capture picture
AM
AM
10:30
10
10:30
0231
Fig1 Shows Time Fig2 Count down
Fig3 Shows Time Fig4 NO. of Pictures
10 sec
remain
MEMORY FULL
In the AUTO mode, if the LCD shows “0000”, it means that the
memory is full. The camera will shut off automatically to save battery
life. Please insert an empty SD memory card for memory space.
9
4
5
1
2
3
LOW BATTERY
D50IR MODEL CAMERA
If the BATTERY indicator turns green, it means that the battery is low.
Please replace batteries with fresh batteries.
1. IR LEDs
2. CAMERA LENS
(COLOR SENSOR)
5
3. CAMERA LENS
6
6
(BLACK & WHITE SENSOR)
NOTE: When left inactive for more than 2 minutes in SETUP and IR
AIM mode, the camera will automatically shutdown. The camera will
need to be restarted to resume operation in SETUP and IR AIM mode.
4. PIR SENSOR
MOUNTING CAMERA
Use the mounting strap included to
mount the camera securely in the
desired location.
5. LCD STATUS DISPLAY
6. LOCKABLE LATCHES
7. WEATHER-RESISTANT CASE
7
Download from Www.Somanuals.com. All Manuals Search And Download.
|