IP8815 IP Phone
User Guide
for Nortel Call Servers
Please read this guide carefully before operating your set.
Retain this guide for future reference.
LGN8815-0996SCUG-0.02
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
Care & Precautions:
Before connecting or using your new phone, take a moment to consider safety and reliability. Use common sense
when locating, connecting and using your IP8815 Phone.
• Locate on a dry level surface. Keep the phone away from the edges of the surface to avoid the potential of a
fall.
• Locate cables to avoid potential for damage. For example, do not locate under rugs or carpet as damage may
result from foot traffic or heavy objects. Also, do not locate cables between the desktop and walls where they
may be crushed, damaging the insulation.
• Check the cables regularly and, if damage is noted, disconnect your phone. Contact your local representative
for a replacement.
• Should liquid spill on the phone, disconnect the unit from power and the network.
• Do not use during lightning storms. Lightning presents a potential shock hazard.
• Clean the IP8815 Phone with a soft dry cloth; do not use liquid cleaners.
• Always use caution when connecting to AC power. Use only with a properly grounded standard AC power
outlet.
What is new in this release?
Issue 0.02
2009.1
second draft
ii
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
Table of Contents
1. IP8815 IP Phone Overview....................................................................................1
2. Installing your IP8815 Phone................................................................................3
3. Using Features of IP8815 Phone ..........................................................................4
3.1.
3.2.
3.3.
3.4.
3.5.
3.6.
3.7.
3.8.
3.9.
Receiving a Call............................................................................................................................ 4
Placing a Call................................................................................................................................ 4
Putting a Call on Hold................................................................................................................... 4
Announcing a Call Transfer.......................................................................................................... 5
Using Blind Call Transfer.............................................................................................................. 5
DSS/ BLF (Presence) ................................................................................................................... 5
Call Forward ................................................................................................................................. 6
3-Party Conference....................................................................................................................... 6
Call Waiting................................................................................................................................... 7
3.10. Redial............................................................................................................................................ 7
3.11. Last Call Return............................................................................................................................ 7
3.12. Speed Dial Buttons....................................................................................................................... 7
3.13. Speed Number Dialing.................................................................................................................. 8
3.14. DND (Do-Not-Disturb)................................................................................................................... 8
3.15. Muting a Call................................................................................................................................. 8
3.16. Accessing Your Voice Mail........................................................................................................... 8
3.17. Hotline/Warm-Line........................................................................................................................ 9
4. Advanced Services and the IP8815 Phone LCD Menu .....................................10
4.1.
4.2.
Using the Call Logs Menu........................................................................................................... 10
Using the Phone Book Menu...................................................................................................... 10
5. Setting Your Preferences....................................................................................13
5.1.
5.2.
LCD Contrast.............................................................................................................................. 13
Ring Setting ................................................................................................................................ 13
5.2.1.
5.2.2.
Setting the Ring Type ......................................................................................................... 13
Setting Line Ring Type and Delay...................................................................................... 14
5.3.
5.4.
5.5.
5.6.
Ringer Off.................................................................................................................................... 15
Enabling Automatic Headset Operation ..................................................................................... 15
Setting Flexible Buttons.............................................................................................................. 16
Time Configuration ..................................................................................................................... 17
5.6.1.
5.6.2.
SNTP Server Address ........................................................................................................ 17
Time Zone........................................................................................................................... 17
DST Auto Adjustment ......................................................................................................... 18
Time Format........................................................................................................................ 18
Date Format........................................................................................................................ 19
5.6.3.
5.6.4.
5.6.5.
5.7.
5.8.
Lock Outgoing Call ..................................................................................................................... 19
Enabling Speed Number Dialing ................................................................................................ 20
iii
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
5.9.
Key Tone..................................................................................................................................... 20
5.10. Language Setting........................................................................................................................ 20
Appendix A Dial Pad Character Set ...........................................................................22
Appendix B Time Zones..............................................................................................23
Appendix C IP8815 Icons............................................................................................24
iv
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
1. IP8815 IP Phone Overview
Your new LG-Nortel IP8815 Phone is an Internet Protocol (IP) phone employing Session Initiation
Protocol (SIP), the well-known open standard for establishing, managing and terminating a
communication session. IP8815 Phone interoperates with call servers, proxies and gateways to
exchange SIP signaling messages for call control. Real-time Transport Protocol (RTP) packets deliver
voice between the end-points over a managed IP network.
Features available to IP8815 Phone through SIP call servers are similar to those of a conventional
business telephone. In addition to the features described in this guide, your call server may provide
additional features, often using dialed feature codes. Refer to your system administrator for further
information.
The IP8815 Phone has fixed feature buttons, soft feature keys, flexible buttons that are configurable, and
dial pad buttons as shown in the figure below.
The eight (8) flexible buttons access lines and features based on the IP Phone configuration. Flexible
buttons assigned for line access, called line buttons, represent a telephone line or a SIP user. A line may
be private, calls to a private line signal at all appearances of the line but an active or held call is only
visible and accessible by the original end-points. A shared line appears at multiple phones and all calls
are visible and accessible by all end-points with the line. Each line button employs LEDs to indicate
status as shown below.
Incoming call
Orange*
Orange*
Orange*
Red
LED flashes at 60 ipm, fast flash
LED On
Line in use at this phone
Call held at this phone
Shared line in use at
another phone
LED flashes at 30 ipm, slow flash
LED On
Shared line call held at
Red
1
LED slow flash
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
another phone
Line not registered w/server
Red/Orange
LED flashes color, red to orange at 30 ipm
* When the LCD displays information for a line, such as when an incoming call first rings, the LED
color is orange otherwise, the LED color will be green.
Flexible buttons not assigned for line access may access features such as Speed dial, Redial and others.
Refer to section 5.5 and your system administrator for further information.
The figure below shows other major components of IP8815 Phone. These components include:
•
•
•
•
•
Handset
Speaker and microphone
Message Wait Indicator (Message LED)
LCD (140 by 48 pixel), displays 5-lines
Flexible button labels
The top line of the LCD indicates a number of icons indicating the connection, status and options for the
IP8815 phone. A list of the icons and there meaning are provided in Appendix C.
2
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
2. Installing your IP8815 Phone
The figure below shows the cable connections for your IP Phone. The LAN and desktop PC connections
employ standard category 5 LAN cables terminated with RJ-45 connectors. The IP Phone supports PoE
(Power over Ethernet) in accordance with the IEEE-802.1af industry standard. When connected to a PoE
complaint LAN port, the IP Phone derives power from the port. If the LAN port does not support PoE, use
the AC/DC adaptor, available separately, for connection to power. The handset connects to the base with
the supplied standard handset coiled cord. Use the chart below to make connections to the IP Phone.
1
2
LAN
PC
Connect the IP Phone LAN port to the LAN wall jack with the provided LAN cable.
Connect the IP Phone PC port to your desktop PC with an RJ-45 terminated
UTP-5 cable.
3
Power
If the LAN port supports PoE (IEEE 802.3af compliant), the AC/DC adapter is not
required. If not supported, connect the IP Phone power port to the DC out of
Power Adapter. Connect the Power Adapter AC plug to an AC wall jack.
4
5
Headset
Handset
Connect Headset RJ-11 jack to the IP Phone headset jack.
Connect the Handset coiled cord to the IP Phone base and handset.
3
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
3. Using Features of IP8815 Phone
3.1. Receiving a Call
When you receive a call, your phone rings, the LCD displays the incoming call information and the
associated line button flashes.
To answer a ringing call:
o
Lift the handset. You may press the speakerphone button, line button or the Answer softkey to
activate the speakerphone. To use a headset, press the headset button.
To end the call:
Hang up the handset. If using the speakerphone, press the speakerphone button. If using the
headset, press the headset button.
o
To refuse a ringing call:
Press Refuse softkey, the IP Phone stops ringing and the call server routes the call.
o
3.2. Placing a Call
You place calls with the handset on-hook or off-hook. Similar to your mobile phone, IP8815 Phone uses
a technique called ‘store and forward dialing’. After you dial a digit, the IP Phone waits about 6 seconds
for additional digits. If you do not dial additional digits, the IP Phone sends the digits you dialed to the call
server for processing. To send the digits immediately, press the # button to indicate dialing is complete,
and then the IP Phone sends the number to the call server.
To place a call:
o
o
o
Lift the handset. You may press the speakerphone button or line button to activate the
speakerphone. To use a headset, press the headset button.
Dial the destination number. After a short delay, the IP Phone sends the number, or dial # to send
the dialed digits immediately.
When the called party answers, begin speaking, the LCD displays the elapsed call time.
To end the call,
Hang up the handset. If using the speakerphone, press the speakerphone button. If using the
headset, press the headset button.
o
3.3. Putting a Call on Hold
You can place a call in a waiting state where the held party cannot hear you and you cannot hear the held
party. The held party receives MOH (Music-On-Hold), if configured in the call server.
While a call is on hold, you can answer or place other calls and can toggle between held calls on the
same line. With Call Hold Ringback enabled, the IP Phone rings as a reminder of calls on hold when you
return the IP Phone to idle. Refer to your system administrator or Installer Guide for further information.
To place a call on hold:
4
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
Press the Hold button or the Hold softkey. The call status changes to hold and you receive dial
tone. You may then select another line to answer or place a call. Note, if you select an idle line and
take no action for about 15 seconds, the line is disconnected.
To retrieve a held call on a different line:
o
o
o
Press the slow flashing line button.
Select the desired call from the displayed call list using Previous-Next softkeys
Select the OK softkey to resume a connection with the call.
To toggle between two calls on the same line:
o
Press the Hold button or the Resume softkey, the active call status changes to hold and the held
call connects.
3.4. Announcing a Call Transfer
Using Announcing a Call Transfer, you send an active call to another extension after announcing the call
transfer to the receiving party.
To transfer an active call:
o
Press the Transfer button or the Transfer softkey. The active call status changes to hold and you
receive dial tone.
o
o
o
Dial the number you wish to receive the transfer.
Await answer and announce the transfer.
Hang-up the handset to complete the transfer.
To cancel a transfer, for example the second party does not answer or is busy:
Press the EndCall softkey.
o
3.5. Using Blind Call Transfer
You can transfer an active call to another extension without talking to the party receiving the call. The call
transfers to the new party without verifying that the new party is there or willing to receive the call.
To transfer an active call without announcing the transfer:
o
o
o
Press the BlindXfr softkey. The active call status changes to hold and you receive dial tone.
Dial the number you wish to receive the transfer.
Hang-up the handset to complete the transfer.
To cancel a transfer, for example you mis-dial the receiving number:
Press the EndCall softkey.
o
3.6. DSS/ BLF (Presence)
Your IP8815 Phone may be assigned with DSS/BLF (Direct Station Selection/Busy Lamp Field) buttons
that address the special needs associated with an Attendant or Secretarial answering position. The
specific needs for these users are:
•
DSS - one-touch calling and transfers to the extensions
5
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
•
BLF (Presence) - visual status indication of the extension, when the associated extension is busy
the LED illuminates red.
To call an idle covered extension:
o
o
Lift the handset. You may press the speakerphone button or the headset button.
Press the DSS button. You may press the DSS button prior to lifting the handset, which activates
the speakerphone and places the call.
To transfer an active call:
o
o
o
Press the DSS button. The IP Phone places the active call on hold and calls the extension.
Await answer and announce the transfer.
To complete the transfer, hang up the handset.
To cancel a transfer, for example the second party does not answer or is busy:
Press the EndCall softkey.
o
3.7. Call Forward
Call forward directs incoming calls to ring at another location that you designate. You can select one of
four (4) conditions that will forward your calls:
-
-
Call Forward Busy – redirects incoming calls if the line is busy.
Call Forward No Answer – redirects incoming calls that are not answered in the configured no
answer time.
-
-
Call Forward Busy or No Answer – redirects incoming calls if the line is busy or not answered
after the no answer time expires.
Call Forward All Calls – immediately redirects all incoming calls.
To set up Call Forward:
o
o
o
o
o
Press the CallFwd softkey.
Use the Previous-Next softkeys to select the desired Call Forward condition.
Press the OK softkey.
Input the destination where you want your calls sent.
Press the OK softkey. The display shows “(x) Fwd to ext” indicating the forward condition and
destination for the calls.
(B) = Busy, (N) = No-answer, (BN) = Busy or No-answer, (U) = Unconditional
To disable Call Forward:
Press the CallFwd softkey. The message “Fwd to xxxx” disappears from the LCD.
o
3.8. 3-Party Conference
The IP Phone has a 3-Party Conference feature that lets you converse with two other parties
simultaneously.
To set-up a conference:
o
Place first call as normal.
6
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
o
o
Press the Conferen softkey. The call status changes to hold and you receive dial tone.
Dial the number you want to join the conference.
When the party answers, press the Join softkey to establish the conference.
To end your conference and disconnect all parties:
Hang up the handset.
o
To cancel a conference, for example the second party does not answer or is busy:
Press the EndCall softkey.
o
3.9. Call Waiting
With Call Waiting configured, while you are in a call the IP Phone alerts you of an incoming call. The line
button flashes and you receive a beep tone over the active conversation to indicate the new call. In
addition, during the ring signal, the LCD displays the incoming caller id so you know who is calling before
you interrupt the current call.
To answer an incoming call while on a call:
o
Press the Answer softkey. The active call changes to the hold state and the new call connects.
3.10. Redial
Your IP Phone saves the last number you dialed and allows you to redial the number with the touch of a
button. The number is stored in memory but is lost if power to the IP Phone is interrupted.
To redial a call:
o
o
Press the Redial softkey. The IP Phone activates the speakerphone and places the call.
Lift the handset for privacy or press the headset button to use the headset.
3.11. Last Call Return
When you answer a call, the IP Phone stores the caller’s contact information so you can return a call later
at the touch of a button. The number is stored in memory but is lost if power to the IP Phone is
interrupted.
To call the last incoming caller:
o
o
Press the LastCall softkey. The IP Phone activates the speakerphone and places the call.
Lift the handset for privacy or press the headset button to use the headset.
3.12. Speed Dial Buttons
Flexible buttons not assigned as a line are available for configuration as feature buttons including Speed
dial. Pressing a Speed dial button selects your line and sends the stored number to the call server for
processing. Refer to your system administrator for further information.
To place a call using Speed dial:
o
Press the desired Speed dial flexible button. The IP Phone activates the speakerphone and places
the call on your line. You may select a different line button on your IP Phone prior to selecting the
Speed dial button.
7
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
Lift the handset for privacy or press the headset button to use the headset
3.13. Speed Number Dialing
Your IP8815 Phone incorporates a Phone Book with up to 100 records. Refer to section 4.2 for
information on use of the Phone Book. Each record includes a name, contact information and a Speed
number (00 to 99). When you dial a Speed number, the IP Phone initiates a call to the contact. Speed
number dialing must be enabled. Refer to your system administrator for further information.
To place a call using a Speed number:
o
Dial the Speed number (00-99) for the desired contact. After a short delay, the IP Phone sends the
contact information from the Phone Book. You may dial # to set up the call immediately. If the
Phone Book has no record of the Speed number, the IP Phone sends the digits dialed to the call
server for processing.
3.14. DND (Do-Not-Disturb)
When the DND (Do Not Disturb) feature is enabled and activated, the IP Phone will not notify you of an
incoming call. The IP Phone does not ring, allowing you to work without interruption from an incoming
call. The call server configuration determines routing of the incoming call while your phone is in DND.
Refer to your system administrator for further information.
To activate DND:
o
While the IP Phone is idle, press the DND button. When active, the DND button LED illuminates
red, and “Do not disturb” displays in the LCD.
To deactivate DND:
Press the illuminated DND button again.
o
3.15. Muting a Call
Mute toggles the microphone of the Handset, Speakerphone and Headset Off and On. When Mute is
active, the connected party will not receive audio from the microphone.
To mute the microphone:
o
Press the Mute button. The Mute button LED illuminates red indicating mute is active.
To turn the microphone back on:
Press the illuminated Mute button again.
o
3.16. Accessing Your Voice Mail
When you have a message waiting, the Message LED flashes to indicate you have new messages in
your mailbox. The IP Phone delivers the message waiting indication for your primary line, line button 1.
To access your voice mailbox:
o
o
Press the Message button. The display indicates the number of messages waiting.
Press Dial softkey. The IP Phone activates the speakerphone and places a call to your voice
mailbox. To listen to your messages, follow the instructions for your voice mail system.
8
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
3.17. Hotline/Warm-Line
With Hotline/Warm-Line operation configured, the IP Phone automatically calls the defined destination
when you take the handset off-hook or press the speaker button. The call initiates immediately, Hotline,
or after a delay of up to 10 seconds, Warm-Line. The later permits you the time to access another feature
or line as needed. Note that with Hotline configured, Speed dial, redial and other automated dialing
features will not operate.
Operation of this feature is automatic.
9
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
4. Advanced Services and the IP8815 Phone LCD Menu
This section describes how to view and use the advanced services available through the LCD menu. The
IP8815 Phone has three context sensitive softkeys, pressing the softkey selects the function or value
shown in the LCD just above the softkey. The left (return) and right navigation buttons navigate through
menus.
The menu items and order of display may be different on your phone based on the service subscription.
Not all features may be available to you based on the call server configuration.
4.1. Using the Call Logs Menu
The IP8815 Phone has access to a log of all calls placed or received by the phone, including incoming
calls that were not answered (missed calls). The LCD displays the call logs that you can use to place a
call to the logged party. You access the call logs with a flexible button assigned for the Call Log function.
Refer to your system administrator for further information.
To access the Call Logs menu:
o
o
o
While in an idle state, press the Call Log flexible button. The
Call Log menu displays with several choices (missed, outgoing
and incoming).
Jan 23 08:30
Call Log
>1.Missed Calls
2.Outgoing Calls
Use the Previous-Next softkeys to select the desired log and
press the OK softkey, or dial the digit in front of the desired
selection.
Previous Next
OK
The log will display information on the calls along with the
received caller id.
Jan 23 08:30
Missed Calls
>1.John,4913 01/16 01:54
2.Sam,4928 01/16 10:31
Previous Next
More
To place a call using the Call Logs:
o
Dial the digit preceding the desired log item or use the Previous-Next softkeys to highlight the
desired log item and use the More softkey to locate and select the Dial softkey.
4.2. Using the Phone Book Menu
The IP8815 Phone has an internal Phone Book with up to 100 entries. Each record includes the contact
name, contact information and Speed number. You can add, delete, edit, dial and search entries from the
Phone Book Menu. You access the Phone Book Menu with a flexible button assigned for the Phone
Book function to search and dial contacts. To manage the Phone Book, access the Phone Book menu
through the LCD Menu. Refer to your system administrator for further information.
To access the Phone Book:
o
Press the Phone Book flexible button, the LCD displays the first
Phone Book record.
Jan 23 08:30
Phone Book (page 1)
>[01]Tom, 1234
[02]Sam, 4928
To call a contact from the Phone Book:
Previous Next
More
o
Access the Phone Book as described above.
10
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
o
Use the Previous-Next softkeys to display the desired record or
dial the digit preceding the desired record.
Jan 23 08:30
Phone Book (page 1)
>[14]Sam.7744
Use the More softkey to locate and select the Dial softkey.
Dial
Edit
More
To add a record to the Phone Book:
o
o
o
Access the Phone Book as described above.
Press the More softkey to display the Add softkey.
Select the Add softkey.
Jan 23 08:30
Phone Book : (Page 1)
>[01]Tom, 1234
[02]Sam,4928
Add
Delete
More
o
Enter the name, contact information, ring type and speed
number, for the record, selecting the OK softkey for each entry.
Use the Mode softkey to enter characters. Refer to Appendix A
Dial Pad Character Set, which shows the relationship between
the dial pad digits and characters.
Jan 23 08:30
Phone Book : Name
Jerry
Mode
More
Å
To edit a record:
o
o
Access the Phone Book as described above.
Use the Previous-Next softkeys to display the desired record or dial the digit preceding the
desired record.
Jan 23 08:30
Phone Book (page 1)
>[14]Sam.7744
o
o
Press the More softkey to display the Edit softkey.
Select the Edit softkey.
Dial
Edit
More
o
Edit the name, contact information, ring type and speed number,
for the record, selecting the OK softkey for each entry. Use the
Mode softkey to enter characters. Refer to Appendix A Dial Pad
Character Set, which shows the relationship between the dial
pad digits and characters.
Jan 23 08:30
Phone Book : Name
Sammy
Mode
More
Å
To delete a record:
o
o
Access the Phone Book as described above.
Jan 23 08:30
Use the Previous-Next softkeys to display the desired record or
dial the digit preceding the desired record.
Phone Book (page 1)
>[11]Sammy.95774
(12)Jerry,5555592
o
o
Press the More softkey to locate the Delete softkey.
Add
Delete
More
Select the Delete softkey and confirm by selecting the Yes
softkey. Caution this action deletes the record from the Phone
Book.
Jan 23 08:30
Data will be lost.
Are you sure?
Yes
No
11
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
To delete all records:
o
o
Access the Phone Book as described above.
Press the More softkey to locate the DelAll softkey.
Jan 23 08:30
Phone Book (page 1)
>[01]Tom,5555598
Find
DelAll
More
o
Select DelAll softkey and confirm the deletion by selecting the
Yes softkey. Caution this action deletes all records from the
Phone Book.
Jan 23 08:30
Data will be lost.
Are you sure?
Yes
No
To search for a record in the Phone Book:
o
o
Access the Phone Book as described above.
Press the More softkey to locate the Find softkey.
Jan 23 08:30
Phone Book (page 1)
>[01]Tom,5555598
Find
DelAll
More
o
o
Select the Find softkey.
Jan 23 08:30
Enter the search criteria (name or contact information). Use the
Mode softkey to enter characters. Refer to Appendix A Dial Pad
Character Set, which shows the relationship between the dial
pad digits and characters.
Search for
Jerry
Mode
OK
Å
Jan 23 08:30
o
Select the OK softkey to view the search results.
Phone Book (page 1)
>[10]Jerry,5555584
[11]Sammy,95774
Previous Next
More
12
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
5. Setting Your Preferences
In the LCD Menu, you can set various preferences for the IP Phone. Settings you can adjust include:
-
-
-
-
-
-
-
-
-
-
LCD contrast
Ring Setting
Ringer off
Headset auto mode
Flexible button settings
Time Configuration
Outgoing Call Lock
Speed Number Dialing
Key Tone
Language
The following paragraphs provide detailed instructions for each of the preferences as well as descriptive
information for each.
5.1. LCD Contrast
The contrast of the LCD is adjustable for best viewing angle.
To adjust the LCD contrast:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 1, or move the cursor to 1.LCD Contrast using the Previous-Next softkeys and press the
OK softkey.
Press the Down softkey to decrease the contrast, or press the
Jan 23 08:30
LCD Contrast
Up softkey to increase the contrast.
Move to another parameter with the Return button,
, and
„„„□□□□
continue the session or press the Settings (
the configuration session.
) button to exit
Down
Up
5.2. Ring Setting
Ring settings determine the ring type (tone) for the phone. In addition, the ring type for each line can be
set with immediate or delayed audible notification. Note the ring type set for a contact in the Phone Book
has priority over the phone or line settings, see section 4.2.
5.2.1. Setting the Ring Type
The IP Phone uses one of fourteen distinctive ring types for incoming call notification. Nine are stored in
the memory of your IP Phone and the remaining five (5) must be downloaded prior to use. By assigning
different ring signals to closely located phones, you can identify the ringing phone. The ring type
assigned for the IP Phone is the “Default Ring Type” that can be set to “ringer off” or one of the fourteen
tones.
To set the ring type for the phone:
13
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
Dial 2, or move the cursor to 2.Ring Setting using the Previous-Next softkeys and press the OK
softkey.
Dial 1, or move the cursor to 1.Default Ring Type using the
Jan 23 08:30
Ring Setting
>1.Default Ring Type
Previous-Next softkeys and press the OK softkey. An asterisk,
», displays in front of the current setting.
2.Line 1 Configuration
Previous Next
OK
o
Select the ring type using the Next softkey. Press the Play
softkey to hear the selected tone.
Jan 23 08:30
Default Ring Type
*Type 1
o
o
Press the OK softkey to save the selected the ring type.
Move to another parameter with the Return button,
, and
Play
Next
OK
continue the session or press the Settings (
the configuration session.
) button to exit
5.2.2. Setting Line Ring Type and Delay
You can assign each line with a different ring type (tone) to distinguish which line is ringing. Selections
for the type include one of up to fourteen tones, “Ringer Off” or “Set to Default”, see section 5.2.1. Of the
fourteen tones, nine are permanently stored in the memory of the phone and the remaining five must be
downloaded before use. In addition, for each line the ring signal can be immediate or delayed. The delay
is set in 1 second increments from 0 (no delay) to 10 seconds.
To set the ring type for a line:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
Dial 2, or move the cursor to 2.Ring Setting using the Previous-Next softkeys and press the OK
softkey.
Dial the Line number plus one (2 for Line 1, 3 for Line 2, etc.), or
Jan 23 08:30
Ring Setting
2.Line 1 Configuration
move the cursor to Line n Configuration using the Previous-
Next softkeys and press the OK softkey. The value of n is the
>3.Line 2 Configuration
Line button number.
Previous Next
OK
o
o
Dial 1, or move the cursor to 1.Ring Type using the Previous-
Next softkeys and press the OK softkey. Note the line number
displays in parenthesis after “Ring Type”.
Jan 23 08:30
Line 2 Configuration
>1. Ring Type
2. Delayed Ring Timer
Previous Next
OK
Select the ring type using the Next softkey. Press the Play
softkey to hear the selected tone. An asterisk, », displays in
front of the current setting.
Jan 23 08:30
Ring Type (2)
*Set to default
o
o
Press the OK softkey to save your entry.
Move to another parameter with the Return button,
Play
Next
OK
, and
continue the session or press the Settings (
) button to exit
14
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
the configuration session.
To set delayed ring for a line:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
Dial 2, or move the cursor to 2.Ring Setting using the Previous-Next softkeys and press the OK
softkey.
Dial the Line number plus one (2 for Line 1, 3 for Line 2, etc.), or
Jan 23 08:30
Ring Setting
2.Line 1 Configuration
move the cursor to Line n Configuration using the Previous-
Next softkeys and press the OK softkey. The value of n is the
>3.Line 2 Configuration
Line button number.
Previous Next
OK
o
o
Dial 2, or move the cursor to 2.Delayed Ring using the
Previous-Next softkeys and press the OK softkey. . Note the
line number is shown in parenthesis after “Delayed Ring Timer”.
Jan 23 08:30
Line 2 Configuration
1. Ring Type
>2. Delayed Ring Timer
Previous Next
OK
Using the dial pad enter the desired delay up to 10 seconds in
one-second increments, zero is no delay. The backspace
softkey will delete the previous character and the Clear softkey
deletes the entire entry.
Jan 23 08:30
Delayed Ring Timer (2)
0
Clear
OK
Å
o
o
Press the OK softkey to save your entry.
Move to another parameter with the Return button,
, and
continue the session or press the Settings ( ) button to exit the configuration session.
5.3. Ringer Off
The IP Phone can be programmed not to ring when an incoming call is received.
To set the Ringer Off parameter:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 3, or move the cursor to 3.Ringer Off using the Previous-
Next softkeys and press the OK softkey.
Press the Yes softkey to enable Ringer Off, or press the No
softkey to disable Ringer Off.
Jan 23 08:30
Ringer Off
Current value is ‘No’
Yes
No
Move to another parameter with the Return button,
, and
continue the session or press the Settings (
the configuration session.
) button to exit
5.4. Enabling Automatic Headset Operation
Your IP8815 Phone supports use of a headset with a standard RJ-11 jack. In the Headset Auto Mode,
pressing a line button automatically connects audio to the headset. Also, redial, Speed dial, Speed
number dialing and click-to-call place calls with audio through the headset.
15
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
To enable Headset Auto Mode:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 4, or move the cursor to 4.Headset Auto Mode using the
Previous-Next softkeys and press the OK softkey.
Press the Yes softkey to enable the Headset Auto Mode or
press the No softkey to disable the Headset Auto Mode.
Jan 23 08:30
Headset Auto Mode
Current value is ‘No’
Yes
No
Move to another parameter with the Return button,
, and
continue the session or press the Settings (
the configuration session.
) button to exit
5.5. Setting Flexible Buttons
Your IP8815 Phone has eight (8) flexible buttons. Normally, the first two (2) buttons are for your line.
The flexible buttons not assigned as line buttons can access various functions. The table below indicates
the available functions with a brief description of each.
Feature
Description
0
1
2
3
4
5
6
7
8
9
No Function
Unassigned
Speed Dial Function
Phone Book Function
Call Log Function
Mute Function
Dials the assigned number
Views the personal phone book
Views the call log list
Toggles the Mute feature on and off
Toggles the Headset on and off
Dials the last number dialed by the user.
Dials the number of the last answered call
Sets the call forwarding configuration
1. Initiates a conference call
2. Joins calls in a conference
Initiates a call transfer
Headset Function
Redial Function
Return Call Function
Set Call Forwarding
Conference Function
10 Transfer Function
11 Hold Function
12 Do not disturb
13 Set Ringer Off
14 Message Function
Places an active call on hold
Toggles the DND on and off
Toggles the ringer on and off
Views the number of new and old messages stored
in the Voice Mail server, and dials the Voice Mail
server by pressing the Dial softkey
To assign a function to a flexible button not used as a line:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
Dial 5, or move the cursor to 5.Flexible Key Setting using the
Jan 23 08:30
Previous-Next softkeys and press the OK softkey.
Press Flexible button
16
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
o
Select the desired flexible button. An asterisk, », displays in
front of the current setting.
Jan 23 08:30
(07) Select Function
* No Function
Select a function using the Previous-Next softkey and press
the OK softkey. Refer to the flexible button functions chart
above.
Previous Next
OK
o
o
If the selected function is Speed dial, enter the speed number
and press the OK softkey to save the entry. To enter
alphanumeric characters select the Mode softkey. Refer to
Appendix A for the character mapping of dial pad digits.
Jan 23 08:30
(07) Enter Number
5559988
Mode
More
Å
Move to another parameter with the Return button,
, and
continue the session or press the Settings (
the configuration session.
) button to exit
5.6. Time Configuration
Within the Time Configuration menu, the IP Address or name of the desired Simple Network Time
Protocol (SNTP) server and the local time zone are defined. In addition, Daylight Savings Time (DST) is
enabled. Consult with your administrator before changing the SNTP server.
5.6.1. SNTP Server Address
SNTP (Simple Network Time Protocol) is a standard protocol that permits a network device to obtain the
network’s current time. For operation with SNTP, the IP8815 IP Phone requires an SNTP server IP
address or name.
To assign the SNTP server address:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 6, or move the cursor to 6.Time Configuration using the Previous-Next softkeys and press
the OK softkey.
Dial 1, or move the cursor to 1.SNTP Server Address using the Previous-Next softkeys and
press the OK softkey.
Input the SNTP server address using the dial pad and press the
Jan 23 08:30
SNTP Server Address
clock.via.net
OK softkey to save the entry. To enter alphanumeric characters
select the Mode softkey. Refer to Appendix A for the character
mapping of dial pad digits.
Mode
More
Å
o
Move to another parameter with the Return button,
, and
continue the session or press the Settings (
the configuration session.
) button to exit
5.6.2. Time Zone
For proper operation of the clock, the IP Phone requires the local time zone. For available time zones,
see Appendix B Time Zones.
To enter the Time Zone:
17
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
Dial 6, or move the cursor to 6.Time Configuration using the Previous-Next softkeys and press
the OK softkey.
Dial 2, or move the cursor to 2.Time Zone using the Previous-
Jan 23 08:30
Next softkeys and press the OK softkey. An asterisk, »,
displays in front of the current selection.
Time Zone
*(GMT-08:00)PACIFIC STAN
(GMT-07:00)MOUNTAIN STA
o
o
Select the nearest region from the display using the Previous-
Previous Next
OK
Next softkeys and press the OK softkey to save the entry.
Move to another parameter with the Return button, , and
continue the session or press the Settings ( ) button to exit the configuration session.
5.6.3. DST Auto Adjustment
The IP8815 Phone automatically adjusts for DST (Daylight Savings Time) when enabled.
To enable/disable automatic daylight savings time:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
o
Dial 6, or move the cursor to 6.Time Configuration using the Previous-Next softkeys and press
the OK softkey.
Dial 3, or move the cursor to 3.DST Auto Adjustment using the Previous-Next softkeys and
press the OK softkey.
Press the Yes softkey to enable DST Auto Adjustment, or press
Jan 23 08:30
the No softkey to disable DST Auto Adjustment.
Move to another parameter with the Return button,
DST Auto Adjustment
Current value is ‘Yes’
, and
continue the session or press the Settings (
the configuration session.
) button to exit
Yes
No
5.6.4. Time Format
The format of the LCD time display can be set for 12-hour format or 24-hour format. In addition, the LCD
time display can be disabled.
To set the display format for time:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 6, or move the cursor to 6.Time Configuration using the Previous-Next softkeys and press
the OK softkey.
Dial 4, or move the cursor to 4.Time Format using the Previous-Next softkeys and press the OK
softkey.
An asterisk, », displays in front of the current setting. Press the
Jan 23 08:30
Time Format
*12 HR (08:30)
Previous-Next softkeys to select the Time Format and press
the OK softkey to save your entry.
o
Move to another parameter with the Return button,
, and
Previous Next
OK
18
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
continue the session or press the Settings (
) button to exit the configuration session.
5.6.5. Date Format
The format of the LCD date displays in the one of the formats below:
-
-
-
-
-
MM/DD (01/22)
DD/MM (22/01)
DD Month (22 Jan)
Month DD (Jan 22)
Disabled, no date display
To set the date display format:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 6, or move the cursor to 6.Time Configuration using the Previous-Next softkeys and press
the OK softkey.
Dial 5, or move the cursor to 5.Date Format using the Previous-Next softkeys and press the OK
softkey.
Press the Previous-Next softkeys to select the display format
Jan 23 08:30
Date Format
and press the OK softkey to save your entry. An asterisk, »,
displays in front of the current setting.
*month/DD (Jan 23)
o
Move to another parameter with the Return button,
, and
Previous Next
OK
continue the session or press the Settings (
the configuration session.
) button to exit
5.7. Lock Outgoing Call
The IP Phone can be configured to allow outgoing calls only if a password is entered. When enabled, the
LCD screen will display the password request and the lock icon as shown. In this mode, the password
must be entered prior to placing an outgoing call.
Jan 23 08:30
Enter Password
Change
OK
Å
To activate this feature, the LCD password must be set, consult your system administrator to set the LCD
password.
To enable/disable the Lock Outgoing Call feature:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
Dial 8, or move cursor to 8.Lock Outgoing Call using the Previous-Next softkeys and press the
OK softkey.
19
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
o
Press the Yes softkey to enable Lock Outgoing Call, or press
the No softkey to disable Lock Outgoing Call.
Jan 23 08:30
Lock Outgoing Call
Current value is ‘No’
Move to another parameter with the Return button,
, and
continue the session or press the Settings (
the configuration session.
) button to exit
Yes
No
5.8. Enabling Speed Number Dialing
The IP8815 Phone includes a Phone Book that supports up to 100 entries. Each Phone Book record
includes a two-digit Speed number, see Speed Number Dialing. When enabled, dialing the Speed
number (00~99) sends the contact number or user id from the associated Phone Book record.
To enable/disable Speed number operation:
o
o
Press the Setting (
) button.
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 9, or move cursor to 9.Speed Number using the Previous-Next softkeys and press the OK
softkey.
Press the Yes softkey to enable Speed number, or press the No
Jan 23 08:30
Speed Number
Current value is ‘Yes’
softkey to disable Speed number.
Move to another parameter with the Return button,
, and
continue the session or press the Settings (
the configuration session.
) button to exit
Yes
No
5.9. Key Tone
When you press a button on the IP8820 phone, the phone will generate a beep tone to indicate that the
button has been pressed. This key tone is optional and can be enabled or disabled using the key tone
setting.
To enable/disable the Key Tone:
o
o
Press the Settings (
) button. .
Dial 3, or move the cursor to 3.Phone Settings using the Previous-Next softkeys and press the
OK softkey.
o
o
o
Dial 10, or move the cursor to 10.Key Tone using the Previous-Next softkeys and press the OK
softkey.
Press the Yes softkey to enable the Key Tone, or press the No
Jan 23 08:30
softkey to disable the Key Tone.
Key Tone
Move to another parameter with the Return button,
, and
Current value is ‘Yes’
continue the session or press the Settings (
the configuration session.
) button to exit
Yes
No
5.10. Language Setting
The IP Phone firmware includes an xml file, which, among other things, determines the languages
available to the phone. The Language setting determines the display of text in the LCD. When the xml
file contains more than one (1) language, you may select the language shown in the display.
To select an available language:
20
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
o
o
Press the Settings (
) button.
Dial 3, or move cursor to 3.Phone Settings using the Previous-Next softkeys, and press the OK
softkey.
o
o
Dial 11, or move cursor to 11.Language using the Previous-Next softkeys, and press the OK
softkey.
Select a Language from the list using the Previous-Next
Jan 23 08:30
softkeys, and press the OK softkey. An asterisk, », displays in
front of the current selection.
Language
*English
o
Move to another parameter with the Return button,
, and
Previous Next
OK
continue the session or press the Settings (
the configuration session.
) button to exit
21
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
Appendix A Dial Pad Character Set
The IP8815 Phone dial pad inputs digits or alphanumeric characters. The table below maps each dial
pad digit to characters available. Three modes are available, dial pad digits, upper case letters and lower
case letters as shown in the table.
Dial Pad Mode
Digit
Upper Case
‘[A]’
Lower Case
‘[a]’
1
2
3
4
5
6
7
8
9
0
*
@ : /
A B C
D E F
@ : /
a b c
d e f
G H I
g h i
J K L
j k l
M N O
P Q R S
T U V
m n o
p q r s
t u v
W X Y Z
. , ? !
. *
w x y z
. , ? !
. *
#
Space (‘ ‘)
Space (‘ ‘)
22
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
Appendix B Time Zones
Country
GMT-12:00 International Date Line, West
GMT-11:00 Midway/Samoa
GMT-10:00 Hawaii
No
Country
No
60
GMT+01:00 Oslo, Norway
GMT+01:00 Paris, France
GMT+01:00 Rome, Italy
30
61
1
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
64
48
65
66
49
50
51
52
53
54
55
67
56
57
58
GMT-09:00 Alaska
62
2
GMT+01:00 Stockholm, Sweden
GMT+01:00 Vienna, Austria
GMT+02:00 Athens, Greece
GMT+02:00 Harare, Zimbabwe
GMT+02:00 Helsinki, Finland
GMT+02:00 Istanbul, Turkey
GMT+02:00 Jerusalem, Israel
GMT+03:00 Kuwait
GMT-08:00 Los Angeles, California
GMT-08:00 Pacific Standard
GMT-07:00 Mountain Standard
GMT-06:00 Central Standard
GMT-06:00 Mexico City, Mexico
GMT-06:00 Saskatc., Canada
GMT-05:00 Bogotá, Colombia
GMT-05:00 Eastern Standard
GMT-05:00 Lima, Peru
3
4
5
6
7
8
9
GMT+03:00 Moscow, Russia
GMT+03:00 Nairobi, Kenya
GMT+03:00 Riyadh, Saudi Arabia
GMT+03:30 Tehran, Iran
10
11
12
13
14
15
16
17
18
63
19
20
21
22
23
24
25
26
27
28
59
29
GMT-05:00 New York, NY
GMT-04:00 Atlantic Standard
GMT-04:00 Caracas, Venezuela
GMT-04:00 La Paz, Bolivia
GMT-03:30 New Found land
GMT-03:00 Brasilia, Brazil
GMT+04:00 Abu Dhabi, UAE
GMT+04:00 Tbilisi, Georgia
GMT+04:30 Kabul, Afghanistan
GMT+05:00 Islamabad, Pakistan
GMT+05:30 New Delhi, India
GMT+06:00 Dhaka, Bangladesh
GMT+06:30 Yangon, Myanmar
GMT+07:00 Bangkok, Thailand
GMT+07:00 Jakarta, Indonesia
GMT+08:00 Beijing, China
GMT+09:00 Seoul, Korea
GMT-03:00 Buenos Aires, Argentina
GMT-03:00 Georgetown, Guyana
GMT-02:00 Inuuk, Greenland
GMT-01:00 Azores, Portugal
GMT-01:00 Cape Verde
GMT 00:00 Casablanca, Morocco
GMT 00:00 Lisbon, Portugal
GMT 00:00 London, England
GMT+01:00 Amsterdam, Netherlands
GMT+01:00 Berlin, Germany
GMT+01:00 Bern, Switzerland
GMT+01:00 Brussels, Belgium
GMT+01:00 Central European
GMT+01:00 Copenhagen, Denmark
GMT+01:00 Madrid, Spain
GMT+09:00 Tokyo, Japan
GMT+09:30 Darwin, Australia
GMT+10:00 Guam Standard
GMT+11:00 Solomon Islands
GMT+12:00 Marshall Islands
GMT+12:00 Auckland, Wellington
GMT+13:00 Nuku’alofa
23
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
IP8815 Nortel IP Phone
User Guide
Appendix C IP8815 Icons
Your IP8815 displays various icons in the upper line of the LCD to assist you in understanding the status
of the phone. Below is a list of icons and their meaning.
LAN or Network connection icon indicates the status of the LAN connection to the IP8815. If the
icon is blinking, the LAN connection is faulty. This icon displays as the first icon on the left.
PC Port icon, when displayed, indicates a device, generally a PC, is connected to the PC port of
the IP8815.
Forward icon indicates calls to the extension are forwarded.
Message icon indicates one or more messages waiting in Voice Mail.
DND icon indicates the IP Phone is in DND and will not notify you of incoming calls.
Hold icon indicates the extension has calls on hold.
Locked icon indicates the IP Phone is locked and a password is required to place calls.
24
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
LGN8815-0996SCUG-0.02
Jan. ‘09
Download from Www.Somanuals.com. All Manuals Search And Download.
|