OPERATOR'S MANUAL
Cat. No.
M12 CPD
13 mm (1/2")
M12™ FUEL™
HAMMER DRILL/DRIVER
TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S
MANUAL.
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING READ ALL SAFETY WARNINGS AND ALL INSTRUCTIONS.
ꢀꢀꢀꢀꢀꢀꢀꢀ)DLOXUHꢀWRꢀIROORZꢀWKHꢀZDUQLQJVꢀDQGꢀLQVWUXFWLRQVꢀPD\ꢀUHVXOWꢀLQꢀHOHFWULFꢀVKRFNꢂꢀ¿UHꢀDQGꢅRUꢀ
VHULRXVꢀLQMXU\ꢁꢀSave all warnings and instructions for future reference.
7KHꢀWHUPꢀꢇSRZHUꢀWRROꢇꢀLQꢀWKHꢀZDUQLQJVꢀUHIHUVꢀWRꢀ\RXUꢀPDLQVꢆRSHUDWHGꢀꢃFRUGHGꢄꢀSRZHUꢀWRROꢀRUꢀ
EDWWHU\ꢆRSHUDWHGꢀꢃFRUGOHVVꢄꢀSRZHUꢀWRROꢁ
‡ꢀ5HPRYHꢀDQ\ꢀDGMXVWLQJꢀNH\ꢀRUꢀZUHQFKꢀEHIRUHꢀ
WORK AREA SAFETY
WXUQLQJꢀWKHꢀSRZHUꢀWRROꢀRQꢁꢀAwrench or a key left
‡ꢀ.HHSꢀZRUNꢀDUHDꢀFOHDQꢀDQGꢀZHOOꢀOLWꢁ Cluttered or
attached to a rotating part of the power tool may
dark areas invite accidents.
result in personal injury.
‡ꢀ'RꢀQRWꢀRSHUDWHꢀSRZHUꢀWRROVꢀLQꢀH[SORVLYHꢀDWPR-
‡ꢀ'RꢀQRWꢀRYHUUHDFKꢁꢀ.HHSꢀSURSHUꢀIRRWLQJꢀDQGꢀ
VSKHUHVꢂꢀVXFKꢀDVꢀLQꢀWKHꢀSUHVHQFHꢀRIꢀÀDPPDEOHꢀ
EDODQFHꢀDWꢀDOOꢀWLPHVꢁ This enables better control
OLTXLGVꢂꢀJDVHVꢀRUꢀGXVWꢁ Power tools create sparks
of the power tool in unexpected situations.
which may ignite the dust or fumes.
‡ꢀ'UHVVꢀSURSHUO\ꢁꢀ'RꢀQRWꢀZHDUꢀORRVHꢀFORWKLQJꢀRUꢀ
‡ꢀ.HHSꢀ FKLOGUHQꢀ DQGꢀ E\VWDQGHUVꢀ DZD\ꢀ ZKLOHꢀ
MHZHOOHU\ꢁꢀ.HHSꢀ\RXUꢀKDLUꢂꢀFORWKLQJꢀDQGꢀJORYHVꢀ
RSHUDWLQJꢀDꢀSRZHUꢀWRROꢁ Distractions can cause
DZD\ꢀIURPꢀPRYLQJꢀSDUWVꢁ Loose clothes, jewel-
you to lose control.
lery or long hair can be caught in moving parts.
‡ꢀ,IꢀGHYLFHVꢀDUHꢀSURYLGHGꢀIRUꢀWKHꢀFRQQHFWLRQꢀRIꢀ
ELECTRICAL SAFETY
GXVWꢀH[WUDFWLRQꢀDQGꢀFROOHFWLRQꢀIDFLOLWLHVꢂꢀHQVXUHꢀ
‡ꢀ3RZHUꢀWRROꢀSOXJVꢀPXVWꢀPDWFKꢀWKHꢀRXWOHWꢁꢀ1HYHUꢀ
WKHVHꢀDUHꢀFRQQHFWHGꢀDQGꢀSURSHUO\ꢀXVHGꢁꢀUse of
PRGLI\ꢀWKHꢀSOXJꢀLQꢀDQ\ꢀZD\ꢁꢀ'RꢀQRWꢀXVHꢀDQ\ꢀ
dust collection can reduce dust-related hazards.
DGDSWHUꢀSOXJVꢀZLWKꢀHDUWKHGꢀꢃJURXQGHGꢄꢀSRZHUꢀ
WRROVꢁꢀ8nmodi¿ed plugs and matching outlets will
POWER TOOL USE AND CARE
reduce risk of electric shock.
‡ꢀ'RꢀQRWꢀIRUFHꢀWKHꢀSRZHUꢀWRROꢁꢀ8VHꢀWKHꢀFRUUHFWꢀ
‡ꢀ$YRLGꢀERG\ꢀFRQWDFWꢀZLWKꢀHDUWKHGꢀRUꢀJURXQGHGꢀ
SRZHUꢀWRROꢀIRUꢀ\RXUꢀDSSOLFDWLRQꢁ The correct
VXUIDFHVꢀVXFKꢀDVꢀSLSHVꢂꢀUDGLDWRUVꢂꢀUDQJHVꢀDQGꢀ
power tool will do the job better and safer at the
UHIULJHUDWRUVꢁꢀThere is an increased risk of electric
rate for which it was designed.
shock if your body is earthed or grounded.
‡ꢀ'RꢀQRWꢀXVHꢀWKHꢀSRZHUꢀWRROꢀLIꢀWKHꢀVZLWFKꢀGRHVꢀQRWꢀ
‡ꢀ'RꢀQRWꢀH[SRVHꢀSRZHUꢀWRROVꢀWRꢀUDLQꢀRUꢀZHWꢀFRQGL-
WXUQꢀLWꢀRQꢀDQGꢀRIIꢁ Any power tool that cannot be
WLRQVꢁꢀWater entering a power tool will increase
controlled with the switch is dangerous and must
the risk of electric shock.
be repaired.
‡ꢀ'RꢀQRWꢀDEXVHꢀWKHꢀFRUGꢁꢀ1HYHUꢀXVHꢀWKHꢀFRUGꢀIRUꢀ
‡ꢀ'LVFRQQHFWꢀWKHꢀSOXJꢀIURPꢀWKHꢀSRZHUꢀVRXUFHꢀ
FDUU\LQJꢂꢀSXOOLQJꢀRUꢀXQSOXJJLQJꢀWKHꢀSRZHUꢀWRROꢁꢀ
DQGꢅRUꢀWKHꢀEDWWHU\ꢀSDFNꢀIURPꢀWKHꢀSRZHUꢀWRROꢀ
.HHSꢀFRUGꢀDZD\ꢀIURPꢀKHDWꢂꢀRLOꢂꢀVKDUSꢀHGJHVꢀ
EHIRUHꢀ PDNLQJꢀ DQ\ꢀ DGMXVWPHQWVꢂꢀ FKDQJLQJꢀ
RUꢀPRYLQJꢀSDUWVꢁꢀDamaged or entangled cords
DFFHVVRULHVꢂꢀ RUꢀ VWRULQJꢀ SRZHUꢀ WRROVꢁꢀ Such
increase the risk of electric shock.
preventive safety measures reduce the risk of
‡ꢀ:KHQꢀRSHUDWLQJꢀDꢀSRZHUꢀWRROꢀRXWGRRUVꢂꢀXVHꢀDQꢀ
starting the power tool accidentally.
H[WHQVLRQꢀFRUGꢀVXLWDEOHꢀIRUꢀRXWGRRUꢀXVHꢁꢀUse
‡ꢀ6WRUHꢀLGOHꢀSRZHUꢀWRROVꢀRXWꢀRIꢀWKHꢀUHDFKꢀRIꢀFKLO-
of a cord suitable for outdoor use reduces the risk
GUHQꢀDQGꢀGRꢀQRWꢀDOORZꢀSHUVRQVꢀXQIDPLOLDUꢀZLWKꢀ
of electric shock.
WKHꢀSRZHUꢀWRROꢀRUꢀWKHVHꢀLQVWUXFWLRQVꢀWRꢀRSHUDWHꢀ
‡ꢀ,IꢀRSHUDWLQJꢀDꢀSRZHUꢀWRROꢀLQꢀDꢀGDPSꢀORFDWLRQꢀ
WKHꢀSRZHUꢀWRROꢁꢀPower tools are dangerous in the
LVꢀXQDYRLGDEOHꢂꢀXVHꢀDꢀUHVLGXDOꢀFXUUHQWꢀGHYLFHꢀ
hands of untrained users.
ꢃ5&'ꢄꢀSURWHFWHGꢀVXSSO\ꢁꢀUse of an RCD reduces
‡ꢀ0DLQWDLQꢀSRZHUꢀWRROVꢁꢀ&KHFNꢀIRUꢀPLVDOLJQPHQWꢀ
the risk of electric shock.
RUꢀELQGLQJꢀRIꢀPRYLQJꢀSDUWVꢂꢀEUHDNDJHꢀRIꢀSDUWVꢀ
DQGꢀDQ\ꢀRWKHUꢀFRQGLWLRQꢀWKDWꢀPD\ꢀDIIHFWꢀWKHꢀ
PERSONAL SAFETY
SRZHUꢀWRRO¶VꢀRSHUDWLRQꢁꢀ,IꢀGDPDJHGꢂꢀKDYHꢀWKHꢀ
SRZHUꢀWRROꢀUHSDLUHGꢀEHIRUHꢀXVHꢁꢀMany accidents
are caused by poorly maintained power tools.
‡ꢀ.HHSꢀFXWWLQJꢀWRROVꢀVKDUSꢀDQGꢀFOHDQꢁ Properly
maintained cutting tools with sharp cutting edges
are less likely to bind and are easier to control.
‡ꢀ8VHꢀWKHꢀSRZHUꢀWRROꢂꢀDFFHVVRULHVꢀDQGꢀWRROꢀELWVꢀ
HWFꢁꢂꢀLQꢀDFFRUGDQFHꢀ ZLWKꢀWKHVHꢀLQVWUXFWLRQVꢂꢀ
WDNLQJꢀLQWRꢀDFFRXQWꢀWKHꢀZRUNLQJꢀFRQGLWLRQVꢀDQGꢀ
WKHꢀZRUNꢀWRꢀEHꢀSHUIRUPHGꢁꢀUse of the power tool
for operations different from those intended could
result in a hazardous situation.
‡ꢀ6WD\ꢀDOHUWꢂꢀZDWFKꢀZKDWꢀ\RXꢀDUHꢀGRLQJꢀDQGꢀXVHꢀ
FRPPRQꢀVHQVHꢀZKHQꢀRSHUDWLQJꢀDꢀSRZHUꢀWRROꢁꢀ
'RꢀQRWꢀXVHꢀDꢀSRZHUꢀWRROꢀZKLOHꢀ\RXꢀDUHꢀWLUHGꢀRUꢀ
XQGHUꢀWKHꢀLQÀXHQFHꢀRIꢀGUXJVꢂꢀDOFRKROꢀRUꢀPHGL-
FDWLRQꢁꢀA moment of inattention while operating
power tools may result in serious personal injury.
‡ꢀ8VHꢀSHUVRQDOꢀSURWHFWLYHꢀHTXLSPHQWꢁꢀ$OZD\Vꢀ
ZHDUꢀH\HꢀSURWHFWLRQꢁ Protective equipment such
as dust mask, non-skid safety shoes, hard hat, or
hearing protection used for appropriate conditions
will reduce personal injuries.
‡ꢀ3UHYHQWꢀ XQLQWHQWLRQDOꢀ VWDUWLQJꢁꢀ (QVXUHꢀ WKHꢀ
VZLWFKꢀLVꢀLQꢀWKHꢀRIIꢆSRVLWLRQꢀEHIRUHꢀFRQQHFWLQJꢀ
WRꢀSRZHUꢀVRXUFHꢀDQGꢅRUꢀEDWWHU\ꢀSDFNꢂꢀSLFNLQJꢀ
XSꢀRUꢀFDUU\LQJꢀWKHꢀWRROꢁꢀCarrying power tools with
your ¿nger on the switch or energising power tools
that have the switch on invites accidents.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY TOOL USE AND CARE
SPECIFIC SAFETY RULES
ion
Exposure to noise can cause hearing loss.
A charger that is suitable for
one type of battery pack may create a risk of re
when used with another battery pack.
-
Use of any other battery
packs may create a risk of injury and re.
tool. Loss of control can cause personal injury.
-
/drilling
Cutting/drilling accessory
contacting a “live” wire may make exposed
metal parts of the power tool “live” and could give
the operator an electric shock.
Shorting the battery termi-
nals together may cause burns or a re.
-
-
Fasteners
contacting a “live” wire may make exposed metal
parts of the power tool “live” and could give the
operator an electric shock.
Liquid ejected from the battery may cause irritation
or burns.
These carry
SERVICE
important information. If unreadable or missing,
contact a MILWAUKEE service facility for a
replacement.
Some dust created by power sanding,
sawing, grinding, drilling, and other construction
activities contains chemicals known to cause
cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
lead from lead-based paint
crystalline silica from bricks and cement and other
masonry products, and
arsenic and chromium from chemically-treated
lumber.
This will ensure that the safety of the power
tool is maintained.
Your risk from these exposures varies, depending
on how often you do this type of work. To reduce
your exposure to these chemicals: work in a well
ventilated area, and work with approved safety
equipment, such as those dust masks that are
specially designed to lter out microscopic par-
ticles.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Capacities
:RRG
No Load
9ROWV No Load ,PSDFWVꢀ
Cat. No. DC
RPM
SHUꢀ0LQXWH Steel )ODWꢀ%LW $XJHUꢀ%LW +ROHꢀ6DZ 6FUHZVꢀꢃGLDꢁꢄ 0DVRQU\
M12 CPD
25.4mm 44.4mm
12 LO 0-450 LO 6750
HI 0-1700 HI 25,500
13mm 28.5mm
(1/2") (1 1/8")
10mm
(3/8")
10mm
(3/8")
(1")
(1 3/4")
ASSEMBLY
FUNCTIONAL DESCRIPTION
3
2
1
WARNING 5HFKDUJHꢀ RQO\ꢀ ZLWKꢀ WKHꢀ
FKDUJHUꢀ VSHFLILHGꢀ IRUꢀ WKHꢀ EDWWHU\ꢁꢀ )RUꢀ VSH-
FL¿FꢀFKDUJLQJꢀLQVWUXFWLRQVꢂꢀUHDGꢀWKHꢀRSHUDWRU¶Vꢀ
PDQXDOꢀVXSSOLHGꢀZLWKꢀ\RXUꢀFKDUJHUꢀDQGꢀEDWWHU\ꢁ
4
,QVHUWLQJꢅ5HPRYLQJꢀWKHꢀ%DWWHU\
To UHPRYHꢀthe battery, push in the release buttons
and pull the battery pack away from the tool.
To LQVHUW the battery, slide the pack into the body of
the tool. Make sure it latches securely into place.
9
5
8
6
7
1.Keyless chuck
2.Clutch adjusting ring
3.Application selector
4.Speed selector
5.Belt hook
6.Fuel Gauge
7.Trigger
8.FWD/REV/LOCK Control Switch
9.LED
SYMBOLOGY
Volts
Direct Current
Impacts per Minute Under
Load (IPM)
No Load Revolutions per
Minute (RPM)
Underwriters Laboratories, Inc.
United States and Canada
5
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
6HOHFWLQJꢀ+DPPHUꢂꢀ'ULOOꢀRUꢀ'ULYHꢀ$FWLRQꢀ
WARNING $OZD\Vꢀ UHPRYHꢀ EDWWHU\ꢀ
SDFNꢀ EHIRUHꢀ FKDQJLQJꢀ RUꢀ UHPRYLQJꢀ DFFHV-
VRULHVꢁꢀ 2QO\ꢀ XVHꢀ DFFHVVRULHVꢀ VSHFLILFDOO\ꢀ
UHFRPPHQGHGꢀIRUꢀWKLVꢀWRROꢁꢀ2WKHUVꢀPD\ꢀEHꢀ
KD]DUGRXVꢁ
1. 7Rꢀ XVHꢀ WKHꢀ KDPPHUꢆGULOOLQJꢀ
mode, rotate the application
selector collar until the hammer
symbol
appears in line with
the arrow. Apply pressure to the
bit to engage the hammering
mechanism.
WARNING 7RꢀUHGXFHꢀWKHꢀULVNꢀRIꢀLQMXU\ꢂꢀ
ZHDUꢀ VDIHW\ꢀ JRJJOHVꢀ RUꢀ JODVVHVꢀ ZLWKꢀ VLGHꢀ
VKLHOGVꢁ
127(ꢈꢀ The number selected on the torque
selector collar has no effect on operation of the
drill in hammer mode.
127(ꢈꢀWhen using carbide bits, do not use wa-
ter to settle dust. Do not attempt to drill through
steel reinforcing rods. This will damage the
carbide bits.
ꢀ
)XHOꢀ*DXJH
To determine the amount of charge left in the bat-
tery, pull the trigger. The Fuel Gauge will light up
for 2-3 seconds.
2. 7RꢀXVHꢀWKHꢀGULOOLQJꢀRQO\ꢀPRGH,
rotate the application selector
collar until the drill symbol
To signal the end of charge, 1 light on the fuel
gauge will Àash for 2-3 seconds.
appears in line with the arrow.
127(ꢈꢀThe number selected on
the torque selector collar has no
effect on operation of the drill in
drilling mode.
,QVWDOOLQJꢀ%LWV
Always remove the battery before inserting or
removing bits. Select the proper style and size bit
for the job.
3. 7Rꢀ XVHꢀ WKHꢀ GULYLQJꢀ VFUHZVꢀ
mode rotate the application
selector collar until the drive
This tool is equipped with a spindle lock. The chuck
can be tightened with one hand, creating higher grip
strengths on the bit.
symbol
appears in line with
1. To open the chuck jaws, turn the sleeve in the
counterclockwise direction.
the arrow. Then rotate the torque
selector collar until the desired
When using drill bits, allow the bit to strike the
bottom of the chuck. Center the bit in the chuck
jaws and lift it about 1.6mm (1/16”) off of
the bottom.
When using screwdriver bits, insert the bit far
enough for the chuck jaws to grip the hex of the
bit.
clutch setting appears in line with
the arrow.
The adjustable clutch, when properly adjusted,
will slip at a preset torque to prevent driving the
screw too deep into different materials and to
prevent damage to the screw or tool.
2. To close the chuck jaws, turn the sleeve in the
clockwise direction. The bit is secure when the
chuck makes a ratcheting sound and the sleeve
can not be rotated any further.
3. To remove the bit, turn the sleeve in the coun-
terclockwise direction.
127(ꢈ A ratcheting sound may be heard when the
chuck is opened or closed. This noise is part of the
locking feature, and does not indicate a problem
with the chuck’s operation.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
The torque speci cations shown here are approximate
values obtained with a fully charged battery pack.
1. To
the tool, grasp the handle rmly and pull
the trigger.
NOTE: An LED is turned on when the trigger is
pulled.
2. To
the speed, increase or decrease the
pressure on the trigger. The further the trigger
is pulled, the greater the speed.
1-5
5-15 Small screws in softwood.
6-10
16-22 Medium screws in softwood or small
screws in hardwood.
3. To
the tool, release the trigger. Make sure
the bit comes to a complete stop before laying
the tool down.
11-15 23-28
16-18 29-40
Large screws in softwoods. Medium
screws in hardwood or large screws in
hardwood with pilot hole.
Because the settings shown in the table are only To protect the battery from damage and extend
a guide, use a piece of scrap material to test the different
clutch settings before driving screws into the workpiece.
its life, the tool’s intelligent circuit monitors current
draw, temperature, and voltage drops.
In extremely high torque, binding, stalling, and short
circuit situations that cause high current draw, the
tool will vibrate for about 5 seconds, the fuel gauge
will ash, and then the tool will turn OFF. To reset,
release the trigger.
Under extreme circumstances, the internal tem-
perature of the battery could become too high.
If this happens, the fuel gauge will ash and the
battery pack will shut off. Let the battery pack cool
and then continue work.
The speed selector is on top of the motor housing.
Allow the tool to come to a complete stop before
changing speeds. See “Applications” for recom-
mended speeds under various
conditions.
1. For
speed, push the
speed selector to display “1”.
2. For
speed, push the
speed selector to display “2”.
The control switch may be set to three positions:
forward, reverse and lock. Due to a lockout mecha-
nism, the control switch can only be adjusted when
the ON/OFF switch is not pressed. Always allow
the motor to come to a complete stop before using
the control switch.
For
(clockwise) rotation,
push in the control switch from the
right side of the tool.
For
(counterclockwise)
rotation, push in the control switch
from the left side of the tool.
LEFT
To
the trigger, push the control
switch to the center position. The
trigger will not work while the con-
trol switch is in the center locked
position. Always lock the trigger
or remove the battery pack before
performing maintenance, changing
accessories, storing the tool and
any time the tool is not in use.
CENTER
7
Download from Www.Somanuals.com. All Manuals Search And Download.
APPLICATIONS
MAINTENANCE
WARNING 7RꢀUHGXFHꢀWKHꢀULVNꢀRIꢀLQMXU\ꢂꢀ
DOZD\VꢀXQSOXJꢀWKHꢀFKDUJHUꢀDQGꢀUHPRYHꢀWKHꢀ
EDWWHU\ꢀSDFNꢀIURPꢀWKHꢀFKDUJHUꢀRUꢀWRROꢀEHIRUHꢀ
SHUIRUPLQJꢀ DQ\ꢀPDLQWHQDQFHꢁꢀ 1HYHUꢀ GLVDV-
VHPEOHꢀ WKHꢀ WRROꢂꢀ EDWWHU\ꢀ SDFNꢀ RUꢀ FKDUJHUꢁꢀ
&RQWDFWꢀ Dꢀ MILWAUKEEꢀ VHUYLFHꢀ IDFLOLW\ꢀ IRUꢀ
$//ꢀUHSDLUVꢁ
WARNING 7RꢀUHGXFHꢀWKHꢀULVNꢀRIꢀHOHF-
WULFꢀVKRFNꢂꢀFKHFNꢀZRUNꢀDUHDꢀIRUꢀKLGGHQꢀSLSHVꢀ
DQGꢀZLUHVꢀEHIRUHꢀGULOOLQJꢀRUꢀGULYLQJꢀVFUHZVꢁ
'ULOOLQJꢀLQꢀ:RRGꢂꢀ&RPSRVLWLRQꢀ0DWHULDOVꢀDQGꢀ
3ODVWLF
When drilling in wood, composition materials and
plastic, select the
drill-only operating mode.
Start the drill slowly, gradually increasing speed as
you drill. When drilling into wood, use wood augers
or twist drill bits. Always use sharp bits. When using
twist drill bits, pull the bit out of the hole frequently
to clear chips from the bit Àutes. To reduce the
chance of splintering, back work with a piece of
scrap wood. Select low speeds for plastics with a
low melting point.
0DLQWDLQLQJꢀ7RROꢀ
Keep your tool, battery pack and charger in good
repair by adopting a regular maintenance program.
After six months to one year, depending on use,
return the tool, battery pack and charger to a
MILWAUKEE service facility for:
‡ Lubrication
‡ Mechanical inspection and cleaning (gears,
spindles, bearings, housing, etc.)
'ULOOLQJꢀLQꢀ0HWDO
When drilling in metal, select the
‡ Electrical inspection (battery pack, charger,
motor)
drill-only
operating mode. Use high speed steel twist drills
or hole saws. Use a center punch to start the hole.
Lubricate drill bits with cutting oil when drilling in
iron or steel. Use a coolant when drilling in nonfer-
rous metals such as copper, brass or aluminum.
Back the material to prevent binding and distortion
on breakthrough.
‡ Testing to assure proper mechanical and
electrical operation
If the tool does not start or operate at full power
with a fully charged battery pack, clean the contacts
on the battery pack. If the tool still does not work
properly, return the tool, charger and battery pack,
to a MILWAUKEE service facility for repairs.
'ULOOLQJꢀLQꢀ0DVRQU\
When drilling in masonry, select the
hammer
WARNING 7RꢀUHGXFHꢀWKHꢀULVNꢀRIꢀSHU-
VRQDOꢀLQMXU\ꢀDQGꢀGDPDJHꢂꢀQHYHUꢀLPPHUVHꢀ\RXUꢀ
WRROꢂꢀEDWWHU\ꢀSDFNꢀRUꢀFKDUJHUꢀLQꢀOLTXLGꢀRUꢀDOORZꢀ
DꢀOLTXLGꢀWRꢀÀRZꢀLQVLGHꢀWKHPꢁ
drill operating mode. Use high speed carbide-tipped
bits. Drilling soft masonry materials such as cinder
block requires little pressure. Hard materials like
concrete require more pressure. A smooth, even
Àow of dust indicates the proper drilling rate. Do not
let the bit spin in the hole without cutting. Do not
use water to settle dust or to cool bit. Both actions
will damage the carbide.
&OHDQLQJ
Clean dust and debris from charger and tool
vents. Keep tool handles clean, dry and free of oil
or grease. Use only mild soap and a damp cloth
to clean the tool, battery pack and charger since
certain cleaning agents and solvents are harmful to
plastics and other insulated parts. Some of these
include petrol, turpentine, lacquer thinner, paint
thinner, chlorinated cleaning solvents, ammonia
and household detergents containing ammonia.
Never use flammable or combustible solvents
around tools.
'ULYLQJꢀ6FUHZVꢀDQGꢀ1XWꢀ5XQQLQJ
Drill a pilot hole when driving screws into thick or
hard materials. Select the
driving screws mode.
Set the torque selector collar to the proper position
and set the speed to low. Use the proper style and
size screwdriver bit for the type of screw you are
using. With the screwdriver bit in the screw, place
the tip of the screw on the workpiece and apply ¿rm
pressure before pulling the trigger. Screws can be
removed by reversing the motor.
5HSDLUV
For repairs, return the tool, battery pack and char-
ger to the nearest service center, please visit
2YHUORDGLQJ
Continuous overloading may cause permanent
damage to tool or battery pack.
customer service centre (Australia Toll Free
Telephone Number 1300 361 505) (New Zealand
Toll Free Telephone Number 0800 279 624).
8
Download from Www.Somanuals.com. All Manuals Search And Download.
ACCESSORIES
WARNING $OZD\VꢀUHPRYHꢀEDWWHU\ꢀSDFNꢀ
EHIRUHꢀFKDQJLQJꢀRUꢀUHPRYLQJꢀDFFHVVRULHVꢁꢀ
2QO\ꢀXVHꢀDFFHVVRULHVꢀVSHFL¿FDOO\ꢀUHFRPPHQG-
HGꢀIRUꢀWKLVꢀWRROꢁꢀ2WKHUVꢀPD\ꢀEHꢀKD]DUGRXVꢁꢀ
For a complete listing of accessories, refer to your
MILWAUKEE Electric Tool catalog or go online
contact your local distributor or service center.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Milwaukee Electric Tool Corporation
13135 West Lisbon Road, Brookfield, Wisconsin U.S.A. 53005
Milwaukee Electric Tool Corporation (Australia)
Techtronic Industries (Australia) Pty. Ltd.
Doncaster, Victoria, Australia, 3108
Milwaukee Electric Tool Corporation (New Zealand)
Techtronic Industries (New Zealand) Pty. Ltd.
Mt Wellington, Auckland, New Zealand, 1060
Professionally made in China for Milwaukee Electric Tool Corporation
58-14-2380d1
Printed in China
961075205-01($)
Download from Www.Somanuals.com. All Manuals Search And Download.
|