OM-477
116 508W
September 2000
Processes
Stick (SMAW) Welding
Air Carbon Arc (CAC-A)
Cutting and Gouging
With Optional Equipment:
TIG (GTAW) Welding
MIG (GMAW) Welding
Flux Cored (FCAW) Welding
Description
Engine Driven Welding Generator
R
Big 40G
Visit our website at
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-1. Symbol Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Arc Welding Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Engine Hazards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-4. Additional Symbols For Installation, Operation, And Maintenance . . . . . . . . . . . . . . . . . . . . .
1-5. Principal Safety Standards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. EMF Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT UTILISATION . . . . . . . . . . . . . . . . . . . . .
1-1. Signification des symboles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-2. Dangers relatifs au soudage à l’arc . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-3. Dangers existant en relation avec le moteur . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1
1
1
2
3
4
4
5
5
5
6
WARNING
This product, when used
for welding or cutting,
produces fumes or
gases which contain
chemicals known to the
State of California to
cause birth defects and,
in some cases, cancer.
(California Health &
Safety Code Section
25249.5 et seq.)
1-4. Dangers supplémentaires en relation avec l’installation, le fonctionnement
et la maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7
8
1-5. Principales normes de sécurité . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1-6. Information sur les champs électromagnétiques . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 2 – DEFINITIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2-1. Symbols And Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SECTION 3 – SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-1. Weld, Power, And Engine Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-2. Dimensions, Weights, And Operating Angles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-3. Fuel Consumption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-4. Duty Cycle And Overheating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-5. AC Auxiliary Power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-6. Optional AC Power Plant Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3-7. Volt-Ampere Curves . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8
9
9
WARNING
9
9
Battery posts, terminals
and related accessories
contain lead and lead
compounds, chemicals
known to the State of
California to cause
cancer and birth defects
or other reproductive
harm. Wash hands after
handling.
10
10
11
11
12
13
SECTION 4 – INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
4-1. Installing Welding Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-2. Connecting The Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-3. Installing Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-4. Engine Prestart Checks . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-5. Connecting To Weld Output Terminals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-6. Selecting Weld Cable Sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4-7. Remote 14 Receptacle RC3 Information (Optional, See Section 4-8) . . . . . . . . . . . . . . . . . .
4-8. Terminal Strip 3T Connections (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14
14
14
15
16
16
17
17
WARNING
The engine exhaust from
this product contains
chemicals known to the
State of California to
cause cancer, birth
defects, or other
SECTION 5 – OPERATING WELDING GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5-1. Front Panel Controls (See Section 5-2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-2. Description Of Front Panel Controls (See Section 5-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5-3. Remote Control (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18
19
20
reproductive harm.
SECTION 6 – OPERATING AUXILIARY EQUIPMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
6-1. 120 Volt Duplex And Optional GFCI Receptacles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-2. 240 Volt Duplex Receptacle (Optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6-3. Connecting Optional Auxiliary Power Plant . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21
22
23
The following terms are
used interchangeably
throughout this manual:
TIG = GTAW
SECTION 7 – MAINTENANCE AND TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
7-1. Routine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-2. Maintenance Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-3. Servicing Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-4. Overload Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-5. Changing Engine Oil And Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-6. Changing Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-7. Inspecting And Cleaning Optional Spark Arrestor Muffler . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-8. Adjusting Engine Weld/Power Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-9. Adjusting Engine Idle Speed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-10. Adjusting Governor Sensitivity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-11. Adjusting Optional High Altitude Carburetor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-12. Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
24
25
26
26
27
28
28
29
30
30
31
31
Stick = SMAW
SECTION 8 – ELECTRICAL DIAGRAMS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
SECTION 9 – AUXILIARY POWER GUIDELINES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
SECTION 10 – PARTS LIST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
OPTIONS AND ACCESSORIES
WARRANTY
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 – SAFETY PRECAUTIONS - READ BEFORE USING
rom _nd_11/98
1-1. Symbol Usage
Means Warning! Watch Out! There are possible hazards
with this procedure! The possible hazards are shown in
the adjoining symbols.
This group of symbols means Warning! Watch Out! possible
Y
Marks a special safety message.
ELECTRIC SHOCK, MOVING PARTS, and HOT PARTS hazards.
Consult symbols and related instructions below for necessary actions
to avoid the hazards.
.
M
e
a
n
s
“
N
o
t
e
”
;
n
o
t
s
a
f
e
t
y
r
e
l
a
t
e
d
.
1-2. Arc Welding Hazards
Y
The symbols shown below are used throughout this manual to
call attention to and identify possible hazards. When you see
the symbol, watch out, and follow the related instructions to
avoid the hazard. The safety information given below is only
a summary of the more complete safety information found in
the Safety Standards listed in Section 1-5. Read and follow all
Safety Standards.
D
D
D
Wear a safety harness if working above floor level.
Keep all panels and covers securely in place.
Clamp work cable with good metal-to-metal contact to workpiece
or worktable as near the weld as practical.
D
D
Insulate work clamp when not connected to workpiece to prevent
contact with any metal object.
Do not connect more than one electrode or work cable to any
single weld output terminal.
Y
Y
Only qualified persons should install, operate, maintain, and
repair this unit.
During operation, keep everybody, especially children, away.
SIGNIFICANT DC VOLTAGE exists after stopping
engine on inverters.
ELECTRIC SHOCK can kill.
D
Stop engine on inverter and discharge input capacitors according
to instructions in Maintenance Section before touching any parts.
Touching live electrical parts can cause fatal shocks
or severe burns. The electrode and work circuit is
electrically live whenever the output is on. The input
power circuit and machine internal circuits are also
ARC RAYS can burn eyes and skin.
Arc rays from the welding process produce intense
visible and invisible (ultraviolet and infrared) rays
that can burn eyes and skin. Sparks fly off from the
weld.
live when power is on. In semiautomatic or automatic wire welding, the
wire, wire reel, drive roll housing, and all metal parts touching the
welding wire are electrically live. Incorrectly installed or improperly
groundedequipment is a hazard.
D
Wear a welding helmet fitted with a proper shade of filter to protect
your face and eyes from arc rays and sparks when welding or
watching (see ANSI Z49.1 and Z87.1 listed in Safety Standards).
D
D
D
Do not touch live electrical parts.
Wear dry, hole-free insulating gloves and body protection.
Insulate yourself from work and ground using dry insulating mats
or covers big enough to prevent any physical contact with the work
or ground.
D
D
D
Wear approved safety glasses with side shields under your
helmet.
Use protective screens or barriers to protect others from flash and
glare; warn others not to watch the arc.
D
Do not use AC output in damp areas, if movement is confined, or if
there is a danger of falling.
Wear protective clothing made from durable, flame-resistant mate-
rial (wool and leather) and foot protection.
D
D
Use AC output ONLY if required for the welding process.
If AC output is required, use remote output control if present on
unit.
FUMES AND GASES can be hazardous.
D
Disconnect input power or stop engine before installing or
servicing this equipment. Lockout/tagout input power according to
OSHA 29 CFR 1910.147 (see Safety Standards).
Welding produces fumes and gases. Breathing
these fumes and gases can be hazardous to your
health.
D
D
Properly install and ground this equipment according to its
Owner’s Manual and national, state, and local codes.
D
D
Keep your head out of the fumes. Do not breathe the fumes.
If inside, ventilate the area and/or use exhaust at the arc to remove
welding fumes and gases.
Always verify the supply ground – check and be sure that input
power cord ground wire is properly connected to ground terminal in
disconnect box or that cord plug is connected to a properly
groundedreceptacle outlet.
D
D
If ventilation is poor, use an approved air-supplied respirator.
Read the Material Safety Data Sheets (MSDSs) and the
manufacturer’s instructions for metals, consumables, coatings,
cleaners, and degreasers.
D
D
When making input connections, attach proper grounding conduc-
tor first – double-check connections.
D
Work in a confined space only if it is well ventilated, or while
wearing an air-supplied respirator. Always have a trained watch-
person nearby. Welding fumes and gases can displace air and
lower the oxygen level causing injury or death. Be sure the breath-
ing air is safe.
Frequently inspect input power cord for damage or bare wiring –
replace cord immediately if damaged – bare wiring can kill.
D
D
D
D
Turn off all equipment when not in use.
Do not use worn, damaged, undersized, or poorly spliced cables.
Do not drape cables over your body.
D
D
Do not weld in locations near degreasing, cleaning, or spraying op-
erations. The heat and rays of the arc can react with vapors to form
highly toxic and irritating gases.
If earth grounding of the workpiece is required, ground it directly
with a separate cable.
Do not weld on coated metals, such as galvanized, lead, or
cadmiumplated steel, unless the coating is removed from the weld
area, the area is well ventilated, and if necessary, while wearing an
air-suppliedrespirator. The coatings and any metals containing
these elements can give off toxic fumes if welded.
D
D
Do not touch electrode if you are in contact with the work, ground,
or another electrode from a different machine.
Use only well-maintained equipment. Repair or replace damaged
parts at once. Maintain unit according to manual.
OM-477 Page 1
Download from Www.Somanuals.com. All Manuals Search And Download.
WELDING can cause fire or explosion.
HOT PARTS can cause severe burns.
D
D
Allow cooling period before maintaining.
Welding on closed containers, such as tanks,
drums, or pipes, can cause them to blow up. Sparks
can fly off from the welding arc. The flying sparks, hot
workpiece, and hot equipment can cause fires and
burns. Accidental contact of electrode to metal objects can cause
sparks, explosion, overheating, or fire. Check and be sure the area is
safe before doing any welding.
Wear protective gloves and clothing when
working on a hot engine.
D
Do not touch hot engine parts or just-welded
parts bare-handed.
NOISE can damage hearing.
D
D
D
Protect yourself and others from flying sparks and hot metal.
Do not weld where flying sparks can strike flammable material.
Noise from some processes or equipment can
damagehearing.
Remove all flammables within 35 ft (10.7 m) of the welding arc. If
this is not possible, tightly cover them with approved covers.
D
Wear approved ear protection if noise level is
high.
D
Be alert that welding sparks and hot materials from welding can
easily go through small cracks and openings to adjacent areas.
D
D
Watch for fire, and keep a fire extinguisher nearby.
MAGNETIC FIELDS can affect pacemakers.
Be aware that welding on a ceiling, floor, bulkhead, or partition can
cause fire on the hidden side.
D
D
Pacemaker wearers keep away.
D
D
Do not weld on closed containers such as tanks, drums, or pipes,
unless they are properly prepared according to AWS F4.1 (see
Safety Standards).
Wearers should consult their doctor before
going near arc welding, gouging, or spot
welding operations.
Connect work cable to the work as close to the welding area as
practical to prevent welding current from traveling long, possibly
unknown paths and causing electric shock and fire hazards.
CYLINDERS can explode if damaged.
D
D
Do not use welder to thaw frozen pipes.
Remove stick electrode from holder or cut off welding wire at
contact tip when not in use.
Shielding gas cylinders contain gas under high
pressure. If damaged, a cylinder can explode. Since
gas cylinders are normally part of the welding
process, be sure to treat them carefully.
D
D
Wear oil-free protective garments such as leather gloves, heavy
shirt, cuffless trousers, high shoes, and a cap.
Remove any combustibles, such as a butane lighter or matches,
from your person before doing any welding.
D
D
Protect compressed gas cylinders from excessive heat, mechani-
cal shocks, slag, open flames, sparks, and arcs.
Install cylinders in an upright position by securing to a stationary
support or cylinder rack to prevent falling or tipping.
FLYING METAL can injure eyes.
D
D
D
D
D
Keep cylinders away from any welding or other electrical circuits.
Never drape a welding torch over a gas cylinder.
D
Welding, chipping, wire brushing, and grinding
cause sparks and flying metal. As welds cool,
they can throw off slag.
Never allow a welding electrode to touch any cylinder.
Never weld on a pressurized cylinder – explosion will result.
D
Wear approved safety glasses with side
shields even under your welding helmet.
Use only correct shielding gas cylinders, regulators, hoses, and fit-
tings designed for the specific application; maintain them and
associated parts in good condition.
D
D
Turn face away from valve outlet when opening cylinder valve.
BUILDUP OF GAS can injure or kill.
Keep protective cap in place over valve except when cylinder is in
use or connected for use.
D
D
Shut off shielding gas supply when not in use.
Always ventilate confined spaces or use ap-
proved air-supplied respirator.
D
Read and follow instructions on compressed gas cylinders,
associated equipment, and CGA publication P-1 listed in Safety
Standards.
1-3. Engine Hazards
STEAM AND HOT COOLANT can burn.
FUEL can cause fire or explosion.
D
D
If possible, check coolant level when engine is
cold to avoid scalding.
D
D
Stop engine and let it cool off before checking or
adding fuel.
Always check coolant level at overflow tank, if
present on unit, instead of radiator (unless told
otherwise in maintenance section or engine
manual).
Do not add fuel while smoking or if unit is near
any sparks or open flames.
D
If the engine is warm, checking is needed, and
there is no overflow tank, follow the next two
statements.
D
D
D
Do not overfill tank – allow room for fuel to expand.
Do not spill fuel. If fuel is spilled, clean up before starting engine.
Dispose of rags in a fireproof container.
D
D
Wear safety glasses and gloves and put a rag over radiator cap.
Turn cap slightly and let pressure escape slowly before completely
removing cap.
OM-477 Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY ACID can BURN SKIN and
EYES.
MOVING PARTS can cause injury.
D
D
Keep away from fans, belts, and rotors.
D
D
D
Do not tip battery.
Keep all doors, panels, covers, and guards
closed and securely in place.
Replace damaged battery.
Flush eyes and skin immediately with water.
D
D
Stop engine before installing or connecting unit.
Have only qualified people remove guards or covers for maint-
enance and troubleshooting as necessary.
D
D
D
D
D
To prevent accidental starting during servicing, disconnect
negative (–) battery cable from battery.
ENGINE EXHAUST GASES can kill.
Keep hands, hair, loose clothing, and tools away from moving
parts.
D
D
Use equipment outside in open, well-ventilated
areas.
Reinstall panels or guards and close doors when servicing is
finished and before starting engine.
If used in a closed area, vent engine exhaust
outside and away from any building air intakes.
Before working on generator, remove spark plugs or injectors to
keep engine from kicking back or starting.
Block flywheel so that it will not turn while working on generator
components.
ENGINE HEAT can cause fire.
D
D
Do not locate unit on, over, or near combustible
surfaces or flammables.
BATTERY EXPLOSION can BLIND.
Keep exhaust and exhaust pipes way from
flammables.
D
D
Always wear a face shield, rubber gloves, and
protective clothing when working on a battery.
Stop engine before disconnecting or connect-
ing battery cables or servicing battery.
EXHAUST SPARKS can cause fire.
D
D
D
D
Do not allow tools to cause sparks when working on a battery.
Do not use welder to charge batteries or jump start vehicles.
Observe correct polarity (+ and –) on batteries.
D
D
Do not let engine exhaust sparks cause fire.
Use approved engine exhaust spark arrestor in
required areas – see applicable codes.
Disconnect negative (–) cable first and connect it last.
1-4. Additional Symbols For Installation, Operation, And Maintenance
FALLING UNIT can cause injury.
OVERUSE can cause OVERHEATING.
D
Use lifting eye to lift unit only, NOT running
gear, gas cylinders, trailer, or any other
accessories.
D
D
Allow cooling period; follow rated duty cycle.
Reduce current or reduce duty cycle before
starting to weld again.
D
Use equipment of adequate capacity to lift and
support unit.
D
Do not block or filter airflow to unit.
D
If using lift forks to move unit, be sure forks are long enough to
extend beyond opposite side of unit.
STATIC (ESD) can damage PC boards.
D
D
Put on grounded wrist strap BEFORE handling
boards or parts.
FLYING SPARKS can cause injury.
Use proper static-proof bags and boxes to
store, move, or ship PC boards.
D
D
Wear a face shield to protect eyes and face.
Shape tungsten electrode only on grinder with
proper guards in a safe location wearing proper
face, hand, and body protection.
TILTING OF TRAILER can cause injury.
D
Sparks can cause fires — keep flammables away.
D
D
Use tongue jack or blocks to support weight.
Properly install welding generator onto trailer
according to instructions supplied with trailer.
OVERHEATING can damage motors.
D
Turn off or unplug equipment before starting or
stopping engine.
READ INSTRUCTIONS.
D
Do not let low voltage and frequency caused by
low engine speed damage electric motors.
D
D
Use only genuine MILLER replacement parts.
Perform engine maintenance and service
according to this manual and the engine
manual.
D
Do not connect 50 or 60 Hertz motors to the 100 Hertz receptacle
where applicable.
OM-477 Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
H.F. RADIATION can cause interference.
ARC WELDING can cause interference.
D
High-frequency (H.F.) can interfere with radio
navigation, safety services, computers, and
communicationsequipment.
D
Electromagnetic energy can interfere with
sensitive electronic equipment such as
computers and computer-driven equipment
such as robots.
D
Have only qualified persons familiar with
electronic equipment perform this installation.
D
Be sure all equipment in the welding area is
electromagneticallycompatible.
D
D
The user is responsible for having a qualified electrician prompt-
ly correct any interference problem resulting from the installa-
tion.
D
D
D
D
To reduce possible interference, keep weld cables as short as
possible, close together, and down low, such as on the floor.
If notified by the FCC about interference, stop using the
equipmentat once.
Locate welding operation 100 meters from any sensitive elec-
tronic equipment.
D
D
Have the installation regularly checked and maintained.
Be sure this welding machine is installed and grounded
according to this manual.
Keep high-frequency source doors and panels tightly shut, keep
spark gaps at correct setting, and use grounding and shielding to
minimize the possibility of interference.
If interference still occurs, the user must take extra measures
such as moving the welding machine, using shielded cables,
using line filters, or shielding the work area.
1-5. Principal Safety Standards
Safety in Welding and Cutting, ANSI Standard Z49.1, from American
Welding Society, 550 N.W. LeJeune Rd, Miami FL 33126
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
from Compressed Gas Association, 1235 Jefferson Davis Highway,
Suite 501, Arlington, VA 22202.
Safety and Health Standards, OSHA 29 CFR 1910, from Superinten-
dent of Documents, U.S. Government Printing Office, Washington, D.C.
20402.
Code for Safety in Welding and Cutting, CSA Standard W117.2, from
Canadian Standards Association, Standards Sales, 178 Rexdale
Boulevard, Rexdale, Ontario, Canada M9W 1R3.
Recommended Safe Practices for the Preparation for Weldingand Cut-
ting of Containers That Have Held Hazardous Substances, American
Welding Society Standard AWS F4.1, from American Welding Society,
550 N.W. LeJeune Rd, Miami, FL 33126
Safe Practices For Occupation And Educational Eye And Face
Protection, ANSI Standard Z87.1, from American National Standards
Institute, 1430 Broadway, New York, NY 10018.
NationalElectrical Code, NFPA Standard 70, from National Fire Protec-
tion Association, Batterymarch Park, Quincy, MA 02269.
Cutting And Welding Processes, NFPA Standard 51B, from National
Fire Protection Association, Batterymarch Park, Quincy, MA 02269.
1-6. EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
1. Keep cables close together by twisting or taping them.
2. Arrange cables to one side and away from the operator.
3. Do not coil or drape cables around your body.
Welding current, as it flows through welding cables, will cause electro-
magnetic fields. There has been and still is some concern about such
fields. However, after examining more than 500 studies spanning 17
years of research, a special blue ribbon committee of the National
Research Council concluded that: “The body of evidence, in the
committee’s judgment, has not demonstrated that exposure to power-
frequency electric and magnetic fields is a human-health hazard.”
However, studies are still going forth and evidence continues to be
examined.Until the final conclusions of the research are reached, you
may wish to minimize your exposure to electromagnetic fields when
welding or cutting.
4. Keep welding power source and cables as far away from
operator as practical.
5. Connect work clamp to workpiece as close to the weld as possi-
ble.
About Pacemakers:
To reduce magnetic fields in the workplace, use the following
procedures:
Pacemaker wearers consult your doctor first. If cleared by your doctor,
then following the above procedures is recommended.
OM-477 Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1 – CONSIGNES DE SÉCURITÉ – LIRE AVANT
UTILISATION
rom _nd_fre 11/98
1-1. Signification des symboles
SignifieMise en garde ! Soyez vigilant ! Cette procédure
présente des risques de danger ! Ceux-ci sont identifiés
par des symboles adjacents aux directives.
Ce groupe de symboles signifie Mise en garde ! Soyez vigilant ! Il y a des
Y
Identifie un message de sécurité particulier.
risques de danger reliés aux CHOCS ÉLECTRIQUES, aux PIÈCES EN
MOUVEMENT et aux PIÈCES CHAUDES. Reportez-vous aux symboles
et aux directives ci-dessous afin de connaître les mesures à prendre pour
éviter tout danger.
.
S
i
g
n
i
f
i
e
N
O
T
A
;
n
’
e
s
t
p
a
s
r
e
l
a
t
i
f
à
l
a
s
é
c
u
r
i
t
é
.
1-2. Dangers relatifs au soudage à l’arc
D
N’utiliser qu’un matériel en bon état. Réparer ou remplacer sur-le-champ
les pièces endommagées. Entretenir l’appareil conformément à ce
manuel.
Y
Les symboles présentés ci-après sont utilisés tout au long du
présent manuel pour attirer votre attention et identifier les ris-
ques de danger. Lorsque vous voyez un symbole, soyez
vigilant et suivez les directives mentionnées afin d’éviter tout
danger. Les consignes de sécurité présentées ci-après ne font
que résumer l’information contenue dans les normes de sécu-
rité énumérées à la section 1-5. Veuillez lire et respecter toutes
ces normes de sécurité.
D
D
D
Porter un harnais de sécurité quand on travaille en hauteur.
Maintenir solidement en place tous les panneaux et capots.
Fixer le câble de retour de façon à obtenir un bon contact métal-métal avec
la pièce à souder ou la table de travail, le plus près possible de la soudure.
Isoler la pince de masse quand pas mis à la pièce pour éviter le contact
D
avec tout objet métallique.
Y
Y
L’installation, l’utilisation, l’entretien et les réparations ne
doivent être confiés qu’à des personnes qualifiées.
Une tension DC importante subsiste à l’intérieur
des onduleurs après avoir coupé l’alimentation.
D
Couper l’alimentation du poste et décharger les condensateurs d’entrée
comme indiqué dans la Section Maintenance avant de toucher des compo-
sants.
Au cours de l’utilisation, tenir toute personne à l’écart et plus
particulièrement les enfants.
LES RAYONS DE L’ARC peuvent pro-
voquer des brûlures dans les yeux et
sur la peau.
Le rayonnement de l’arc du procédé de soudage génère
des rayons visibles et invisibles intenses (ultraviolets et
UN CHOC ÉLECTRIQUE peut tuer.
Un simple contact avec des pièces électriques peut
provoquer une électrocution ou des blessures graves.
L’électrode et le circuit de soudage sont sous tension dès
que l’appareil est sur ON. Le circuit d’entrée et les circuits
internes de l’appareil sont également sous tension à ce
infrarouges) susceptibles de provoquer des brûlures dans les yeux et sur la
peau. Des étincelles sont projetées pendant le soudage.
moment-là. En soudage semi-automatique ou automatique, le fil, le dévidoir, le
logement des galets d’entraînement et les pièces métalliques en contact avec
le fil de soudage sont sous tension. Des matériels mal installés ou mal mis à la
terre présentent un danger.
D
Porter un casque de soudage muni d’un écran de filtre approprié pour pro-
téger votre visage et vos yeux pendant le soudage ou pour regarder (voir
ANSI Z49.1 et Z87.1 énuméré dans les normes de sécurité).
D
D
Ne jamais toucher les pièces électriques sous tension.
D
D
D
Porter des protections approuvés pour les oreilles si le niveau sondre est
trop élevé.
Porter des gants et des vêtements de protection secs ne comportant pas
de trous.
Utiliser des écrans ou des barrières pour protéger des tiers de l’éclair et de
l’éblouissement; demander aux autres personnes de ne pas regarder l’arc.
Porter des vêtements de protection constitué dans une matière durable, ré-
sistant au feu (laine ou cuir) et une protection des pieds.
D
S’isoler de la pièce et de la terre au moyen de tapis ou d’autres moyens iso-
lants suffisamment grands pour empêcher le contact physique éventuel
avec la pièce ou la terre.
D
D
D
D
Ne pas se servir de source électrique àcourant électrique dans les zones
humides, dans les endroits confinés ou là où on risque de tomber.
LES FUMÉES ET LES GAZ peuvent
être dangereux.
Se servir d’une source électrique àcourant électrique UNIQUEMENT si le
procédé de soudage le demande.
Le soudage génère des fumées et des gaz. Leur inhalation
peut être dangereux pour votre santé.
Si l’utilisation d’une source électrique àcourant électrique s’avère néces-
saire, se servir de la fonction de télécommande si l’appareil en est équipé.
Couper l’alimentation ou arrêter le moteur avant de procéder à l’installation,
à la réparation ou à l’entretien de l’appareil. Déverrouiller l’alimentation
selon la norme OSHA 29 CFR 1910.147 (voir normes de sécurité).
D
D
Eloigner votre tête des fumées. Ne pas respirer les fumées.
À l’interieur, ventiler la zone et/ou utiliser un échappement au niveau de
l’arc pour l’évacuation des fumées et des gaz de soudage.
D
D
Installer et mettre à la terre correctement cet appareil conformément à son
manuel d’utilisation et aux codes nationaux, provinciaux et municipaux.
D
D
Si la ventilation est insuffisante, utiliser un respirateur à alimentation d’air
homologué.
Toujours vérifier la terre du cordon d’alimentation – Vérifier et s’assurer que
le fil de terre du cordon d’alimentation est bien raccordé à la borne de terre
du sectionneur ou que la fiche du cordon est raccordée à une prise
correctement mise à la terre.
Lire les spécifications de sécurité des matériaux (MSDSs) et les instruc-
tions du fabricant concernant les métaux, les consommables, les
revêtements, les nettoyants et les dégraisseurs.
D
Travailler dans un espace fermé seulement s’il est bien ventilé ou en por-
tant un respirateur à alimentation d’air. Demander toujours à un surveillant
dûment formé de se tenir à proximité. Des fumées et des gaz de soudage
peuvent déplacer l’air et abaisser le niveau d’oxygène provoquant des
blessures ou des accidents mortels. S’assurer que l’air de respiration ne
présente aucun danger.
D
D
En effectuant les raccordements d’entrée fixer d’abord le conducteur de
mise à la terre approprié et contre-vérifier les connexions.
Vérifier fréquemment le cordon d’alimentation pour voir s’il n’est pas en-
dommagé ou dénudé – remplacer le cordon immédiatement s’il est
endommagé – un câble dénudé peut provoquer une électrocution.
D
D
Ne pas souder dans des endroits situés à proximité d’opérations de dé-
graissage, de nettoyage ou de pulvérisation. La chaleur et les rayons de
l’arc peuvent réagir en présence de vapeurs et former des gaz hautement
toxiques et irritants.
D
D
Mettre l’appareil hors tension quand on ne l’utilise pas.
Ne pas utiliser des câbles usés, endommagés, de grosseur insuffisante ou
mal épissés.
Ne pas souder des métaux munis d’un revêtement, tels que l’acier galvani-
sé, plaqué en plomb ou au cadmium à moins que le revêtement n’ait été
enlevé dans la zone de soudure, que l’endroit soit bien ventilé, et si néces-
saire, en portant un respirateur à alimentation d’air. Les revêtements et
tous les métaux renfermant ces éléments peuvent dégager des fumées
toxiques en cas de soudage.
D
D
Ne pas enrouler les câbles autour du corps.
Si la pièce soudée doit être mise à la terre, le faire directement avec un
câble distinct – ne pas utiliser le connecteur de pièce ou le câble de retour.
D
Ne pas toucher l’électrode quand on est en contact avec la pièce, la terre ou
une électrode provenant d’une autre machine.
OM-477 Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
LE SOUDAGE peut provoquer un in-
cendie ou une explosion.
DES PIÈCES CHAUDES peuvent
provoquer des brûlures graves.
D
Prévoir une période de refroidissement avant d’effec-
tuer des travaux d’entretien.
Le soudage effectué sur des conteneurs fermés tels que
des réservoirs, tambours ou des conduites peut provoquer
leur éclatement. Des étincelles peuvent être projetées de
D
Porter des gants et des vêtements de protection pour
l’arc de soudure. La projection d’étincelles, des pièces chaudes et des
équipements chauds peut provoquer des incendies et des brûlures. Le contact
accidentel de l’électrode avec des objets métalliques peut provoquer des
étincelles, une explosion, un surchauffement ou un incendie. Avant de
commencer le soudage, vérifier et s’assurer que l’endroit ne présente pas de
danger.
travailler sur un moteur chaud.
D
Ne pas toucher à mains nues les parties chaudes du moteur ni les pièces
récemment soudées.
LE BRUIT peut affecter l’ouïe.
D
D
D
Se protéger et d’autres personnes de la projection d’étincelles et de métal
chaud.
Ne pas souder dans un endroit là où des étincelles peuvent tomber sur des
substances inflammables.
Le bruit des processus et des équipements peut affecter
l’ouïe.
Déplacer toutes les substances inflammables à une distance de 10,7 m de
l’arc de soudage. En cas d’impossibilité les recouvrir soigneusement avec
des protections homologués.
D
Porter des protections approuvés pour les oreilles si
le niveau sondre est trop élevé.
D
Des étincelles et des matériaux chauds du soudage peuvent facilement
passer dans d’autres zones en traversant de petites fissures et des
ouvertures.
LES CHAMPS MAGNÉTIQUES peuvent
affecter les stimulateurs cardiaques.
D
D
Surveiller tout déclenchement d’incendie et tenir un extincteur à proximité.
Le soudage effectué sur un plafond, plancher, paroi ou séparation peut dé-
clencher un incendie de l’autre côté.
D
D
Porteurs de stimulateur cardiaque, restez à distance.
D
D
Ne pas effectuer le soudage sur des conteneurs fermés tels que des réser-
voirs, tambours, ou conduites, à moins qu’ils n’aient été préparés
correctement conformément à AWS F4.1 (voir les normes de sécurité).
Les porteurs d’un stimulateur cardiaque doivent
d’abord consulter leur médecin avant de s’approcher
des opérations de soudage à l’arc, de gougeage ou
de soudage par points.
Brancher le câble sur la pièce le plus près possible de la zone de soudage
pour éviter le transport du courant sur une longue distance par des che-
mins inconnus éventuels en provoquant des risques d’électrocution et
d’incendie.
Si des BOUTEILLES sont endomma-
gées, elles pourront exploser.
Des bouteilles de gaz protecteur contiennent du gaz sous
haute pression. Si une bouteille est endommagée, elle peut
exploser. Du fait que les bouteilles de gaz font normale-
ment partie du procédé de soudage, les manipuler avec
précaution.
D
D
Ne pas utiliser le poste de soudage pour dégeler des conduites gelées.
En cas de non utilisation, enlever la baguette d’électrode du porte-électro-
de ou couper le fil à la pointe de contact.
D
D
Porter des vêtements de protection dépourvus d’huile tels que des gants
en cuir, une chemise en matériau lourd, des pantalons sans revers, des
chaussures hautes et un couvre chef.
Avant de souder, retirer toute substance combustible de vos poches telles
qu’un allumeur au butane ou des allumettes.
D
Protéger les bouteilles de gaz comprimé d’une chaleur excessive, des
chocs mécaniques, du laitier, des flammes ouvertes, des étincelles et des
arcs.
DES PARTICULES VOLANTES
peuvent blesser les yeux.
D
D
Placer les bouteilles debout en les fixant dans un support stationnaire ou
dans un porte-bouteilles pour les empêcher de tomber ou de se renverser.
D
Le soudage, l’écaillement, le passage de la pièce
à la brosse en fil de fer, et le meulage génèrent
des étincelles et des particules métalliques vo-
Tenir les bouteilles éloignées des circuits de soudage ou autres circuits
électriques.
D
D
Ne jamais placer une torche de soudage sur une bouteille à gaz.
lantes. Pendant la période de refroidissement des soudures, elles ris-
quent de projeter du laitier.
Une électrode de soudage ne doit jamais entrer en contact avec une bou-
teille.
D
Porter des lunettes de sécurité avec écrans latéraux ou un écran facial.
D
D
Ne jamais souder une bouteille pressurisée – risque d’explosion.
Utiliser seulement des bouteilles de gaz protecteur, régulateurs, tuyaux et
raccords convenables pour cette application spécifique; les maintenir ainsi
que les éléments associés en bon état.
LES ACCUMULATIONS DE GAZ ris-
quent de provoquer des blessures ou
même la mort.
D
D
Ne pas tenir la tête en face de la sortie en ouvrant la soupape de la bouteille.
Maintenir le chapeau de protection sur la soupape, sauf en cas d’utilisation
ou de branchement de la bouteille.
D
Fermer l’alimentation du gaz protecteur en cas de
non utilisation.
D
Lire et suivre les instructions concernant les bouteilles de gaz comprimé,
les équipements associés et les publication P-1 CGA énumérées dans les
normes de sécurité.
D
Veiller toujours à bien aérer les espaces confinés ou se servir d’un respi-
rateur d’adduction d’air homologué.
1-3. Dangers existant en relation avec le moteur
LE CARBURANT MOTEUR peut provo-
quer un incendie ou une explosion.
LA VAPEUR ET LE LIQUIDE DE
REFROIDISSEMENT CHAUD peuvent
provoquer des brûlures.
D
D
Arrêter le moteur avant de vérifier le niveau de carbu-
rant ou de faire le plein.
D
Il est préférable de vérifier le liquide de
refroidissement une fois le moteur refroidi pour éviter
de se brûler.
Ne pas faire le plein en fumant ou proche d’une sour-
ce d’étincelles ou d’une flamme nue.
D
D
D
Ne pas faire le plein de carburant à ras bord; prévoir de l’espace pour son
expansion.
D
Toujours vérifier le niveau de liquide de refroidissement dans le vase
d’expansion (si présent), et non dans le radiateur (sauf si précisé autre-
ment dans la section maintenance du manuel du moteur).
Faire attention de ne pas renverser de carburant. Nettoyer tout carbu-
rant renversé avant de faire démarrer le moteur.
D
D
D
Si le moteur est chaud et que le liquide doit être vérifié, opérer comme
suivant :
Jeter les chiffons dans un récipient ignifuge.
Mettre des lunettes de sécurité et des gants, placer un torchon sur le
bouchon du radiateur.
Dévisser le bouchon légèrement et laisser la vapeur s’échapper avant
d’enlever le bouchon.
OM-477 Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
DES ORGANES MOBILES peuvent
provoquer des blessures.
L’ACIDE DE LA BATTERIE peut pro-
voquer des brûlures dans les YEUX et
sur la PEAU.
D
Ne pas approcher les mains des ventilateurs, cour-
roies et autres pièces en mouvement.
D
D
D
Ne pas renverser la batterie.
D
Maintenir fermés et fixement en place les portes,
panneaux, recouvrements et dispositifs de
protection.
Remplacer une batterie endommagée.
Rincer immédiatement les yeux et la peau à l’eau.
D
D
Arrêter le moteur avant d’installer ou brancher l’appareil.
Demander seulement à un personnel qualifié d’enlever les dispositifs de
sécurité ou les recouvrements pour effectuer, s’il y a lieu, des travaux
d’entretien et de dépannage.
LES GAZ D’ÈCHAPPEMENT DU
MOTEUR peuvent provoquer des
accidents mortels.
D
D
D
Pour empêcher tout démarrage accidentel pendant les travaux d’entre-
tien, débrancher le câble négatif (–) de batterie de la borne.
Ne pas approcher les mains, cheveux, vêtements lâches et outils des or-
ganes mobiles.
D
Utiliser l’équipement à l’extérieur dans des zones ou-
Remettre en place les panneaux ou les dipositifs de protection et fermer
les portes à la fin des travaux d’entretien et avant de faire démarrer le
moteur.
vertes et bien ventilées.
D
En cas d’utilisation dans un endroit fermé évacuer les gaz d’échappe-
ment du moteur vers l’extérieur à distance des entrées d’air dans les bâti-
ments.
D
D
Avant d’intervenir, déposer les bougies ou injecteurs pour éviter la mise
en route accidentelle du moteur.
Bloquer le volant moteur pour éviter sa rotation lors d’une intervention
sur le générateur.
LA CHALEUR DU MOTEUR peut pro-
voquer un incendie.
L’EXPLOSION DE LA BATTERIE peut
RENDRE AVEUGLE.
D
Ne pas placer l’appareil sur, au-dessus ou à proximité
de surfaces inflammables.
D
Toujours porter une protection faciale, des gants en
caoutchouc et vêtements de protection lors d’une in-
tervention sur la batterie.
D
Tenir
à
distance les produits inflammables de
l’échappement.
D
D
D
Arrêter le moteur avant de débrancher ou de brancher les câbles de
batterie.
LES ÉTINCELLES À L’ÉCHAPPEMENT
peuvent provoquer un incendie.
Eviter de provoquer des étincelles avec les outils en travaillant sur la
batterie.
Ne pas utiliser le poste de soudage pour charger les batteries ou des vé-
hicules de démarrage rapide.
D
D
Empêcher les étincelles d’échappement du moteur
de provoquer un incendie.
D
D
Observer la polarité correcte (+ et –) sur les batteries.
Utiliser uniquement un pare-étincelles approuvé –
Débrancher le câble négatif (–) en premier lieu. Le rebrancher en dernier
lieu.
voir codes en vigueur.
1-4. Dangers supplémentaires en relation avec l’installation, le fonctionnement
et la maintenance
LA CHUTE DE L’APPAREIL peut
blesser.
L’EMPLOI EXCESSIF peut
SURCHAUFFER L’ÉQUIPEMENT.
D
D
Utiliser l’anneau de levage uniquement pour soulever
l’appareil lui-même ; sans chariot, de bouteilles de
gaz, remorque, ou autres accessoires.
D
D
D
Laisser l’équipement refroidir ; respecter le facteur de
marche nominal.
Réduire le courant ou le facteur de marche avant de
poursuivre le soudage.
Utiliser un équipement de levage de capacité suffi-
sante pour lever l’appareil.
Ne pas obstruer les passages d’air du poste.
D
En utilisant des fourches de levage pour déplacer l’unité, s’assurer
que les fourches sont suffisamment longues pour dépasser du côté
opposé de l’appareil.
LES
CHARGES
peuvent
ÉLECTROSTATIQUES
LES ÉTINCELLES VOLANTES ris-
quent de provoquer des blessures.
endommager les circuits imprimés.
D
Établir la connexion avec la barrette de terre avant de
manipuler des cartes ou des pièces.
D
Porter un écran facial pour protéger le visage et les
yeux.
D
Utiliser des pochettes et des boîtes antistatiques
pour stocker, déplacer ou expédier des cartes de
circuits imprimes.
D
D
Affuterr l’électrode au tungstène uniquement à la meuleuse dotée de pro-
tecteurs. Cette manoeuvre est à exécuter dans un endroit sûr lorsque
l’on porte l’équipement homologué de protection du visage, des mains et
du corps.
UNE REMORQUE QUI BASCULE peut
entraîner des blessures.
Les étincelles risquent de causer un incendie – éloigner toute substance
inflammable.
D
D
Utiliser les supports de la remorque ou des blocs
pour soutenir le poids.
LE SURCHAUFFEMENT peut endom-
mager le moteur électrique.
Installer convenablement le poste sur la remorque
comme indiqué dans le manuel s’y rapportant.
D
Arrêter ou déconnecter l’équipement avant de dé-
marrer ou d’arrêter le moteur.
LIRE LES INSTRUCTIONS.
D
Ne pas laisser tourner le moteur trop lentement sous
risque d’endommager le moteur électrique à cause
d’une tension et d’une fréquence trop faibles.
D
D
Utiliser seulement les pièces de rechange d’origine.
Effecteur la maintenance et la mise en service
D
Ne pas brancher de moteur de 50 ou de 60 Hz à la prise de 100 Hz, s’il y a
d’après le manuel et celui du moteur.
lieu.
OM-477 Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
LE RAYONNEMENT HAUTE FRÉ-
QUENCE (H.F.) risque de provoquer
des interférences.
LE SOUDAGE À L’ARC risque de
provoquer des interférences.
D
L’énergie électromagnétique risque de provoquer
des interférences pour l’équipement électronique
sensible tel que les ordinateurs et l’équipement com-
mandé par ordinateur tel que les robots.
D
Le rayonnement haute fréquence (H.F.) peut
provoquer des interférences avec les équipements
de radio–navigation et de communication, les
services de sécurité et les ordinateurs.
D
D
Veiller à ce que tout l’équipement de la zone de soudage soit compatible
électromagnétiquement.
D
D
Demander seulement à des personnes qualifiées familiarisées avec des
équipements électroniques de faire fonctionner l’installation.
Pour réduire la possibilité d’interférence, maintenir les câbles de souda-
ge aussi courts que possible, les grouper, et les poser aussi bas que pos-
sible (ex. par terre).
L’utilisateur est tenu de faire corriger rapidement par un électricien quali-
fié les interférences résultant de l’installation.
D
D
D
Veiller à souder à une distance de 100 mètres de tout équipement élec-
tronique sensible.
D
D
D
Si le FCC signale des interférences, arrêter immédiatement l’appareil.
Effectuer régulièrement le contrôle et l’entretien de l’installation.
Veiller à ce que ce poste de soudage soit posé et mis à la terre conformé-
ment à ce mode d’emploi.
Maintenir soigneusement fermés les portes et les panneaux des sources
de haute fréquence, maintenir les éclateurs à une distance correcte et
utiliser une terre et et un blindage pour réduire les interférences
éventuelles.
En cas d’interférences après avoir pris les mesures précédentes, il in-
combe à l’utilisateur de prendre des mesures supplémentaires telles que
le déplacement du poste, l’utilisation de câbles blindés, l’utilisation de fil-
tres de ligne ou la pose de protecteurs dans la zone de travail.
1-5. Principales normes de sécurité
Safety in Welding and Cutting, norme ANSI Z49.1, de l’American Weld-
ing Society, 550 N.W. Lejeune Rd, Miami FL 33126
Safe Handling of Compressed Gases in Cylinders, CGA Pamphlet P-1,
de la Compressed Gas Association, 1235 Jefferson Davis Highway,
Suite 501, Arlington, VA 22202.
Safety and Health Sandards, OSHA 29 CFR 1910, du Superintendent
of Documents, U.S. Government Printing Office, Washington, D.C.
20402.
Règles de sécurité en soudage, coupage et procédés connexes, norme
CSA W117.2, de l’Association canadienne de normalisation, vente de
normes, 178 Rexdale Boulevard, Rexdale (Ontario) Canada M9W 1R3.
RecommendedSafe Practice for the Preparation for Welding and Cut-
ting of Containers That Have Held Hazardous Substances, norme AWS
F4.1, de l’American Welding Society, 550 N.W. Lejeune Rd, Miami FL
33126
Safe Practices For Occupation And Educational Eye And Face Protec-
tion, norme ANSI Z87.1, de l’American National Standards Institute,
1430 Broadway, New York, NY 10018.
NationalElectrical Code, NFPA Standard 70, de la National Fire Protec-
tion Association, Batterymarch Park, Quincy, MA 02269.
Cutting and Welding Processes, norme NFPA 51B, de la National Fire
Protection Association, Batterymarch Park, Quincy, MA 02269.
1-6. Information sur les champs électromagnétiques
Données sur le soudage électrique et sur les effets, pour l’organisme,
des champs magnétiques basse fréquence
Afin de réduire les champs électromagnétiques dans l’environnement
de travail, respecter les consignes suivantes :
1
Garder les câbles ensembles en les torsadant ou en les
attachant avec du ruban adhésif.
Le courant de soudage, pendant son passage dans les câbles de sou-
dage, causera des champs électromagnétiques. Il y a eu et il y a encore
un certain souci à propos de tels champs. Cependant, après avoir ex-
aminé plus de 500 études qui ont été faites pendant une période de
recherche de 17 ans, un comité spécial ruban bleu du National Re-
search Council a conclu: “L’accumulation de preuves, suivant le
jugement du comité, n’a pas démontré que l’exposition aux champs
magnétiqueset champs électriques à haute fréquence représente un
risque à la santé humaine”. Toutefois, des études sont toujours en cours
et les preuves continuent à être examinées. En attendant que les con-
clusions finales de la recherche soient établies, il vous serait
souhaitablede réduire votre exposition aux champs électromagnéti-
ques pendant le soudage ou le coupage.
2
3
Mettre tous les câbles du côté opposé de l’opérateur.
Ne pas courber pas et ne pas entourer pas les câbles autour de
votre corps.
4
5
Garder le poste de soudage et les câbles le plus loin possible de
vous.
Relier la pince de masse le plus près possible de la zone de
soudure.
Consignes relatives aux stimulateurs cardiaques :
Les personnes qui portent un stimulateur cardiaque doivent avant tout
consulter leur docteur. Si vous êtes déclaré apte par votre docteur, il est
alors recommandé de respecter les consignes ci–dessus.
OM-477 Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2 – DEFINITIONS
2-1. Symbols And Definitions
Fast (Run, Weld/
Power)
Stop Engine
Slow (Idle)
Output
Start Engine
Engine Oil
Fast/Slow
(Run/Idle)
Battery (Engine)
Check Valve
Clearance
Protective Earth
(Ground)
Circuit Breaker
Positive
Fuel
Certified/Trained
Mechanic
Negative
Welding Arc
Remote 14
Amperes
Volts
Panel/Local
Temperature
14
A V
Read Operator’s
Engine Coolant
Temperature
G
Engine
1
Manual
Alternating
Current
Time
Hours
Seconds
h
s
Stick Welding
(SMAW)
Constant Current
(CC)
MIG Welding
(GMAW)
Constant Voltage
(CV)
Do Not Switch
While Welding
Single Phase
Three Phase
1
3
SECTION 3 – SPECIFICATIONS
3-1. Weld, Power, And Engine Specifications
Maximum
Open-Circuit
Voltage
Welding
Mode
Weld Output
Range
Rated Welding
Output
Auxiliary Power
Rating
Engine
Fuel Capacity
375 A, 35 Volts DC,
50% Duty Cycle
Teledyne-Continental
TM-20 Water-Cooled,
Three-Cylinder,
38 HP Gasoline
Engine
CC/DC
50 – 440 A
95
40
Single-Phase,
3 kVA/kW, 26 A,
120 V AC, 60 Hz
300 A, 32 Volts DC
100% Duty Cycle
16 gal (60.6 L)
CV/DC
(Optional)
300 A, 32 Volts DC,
100% Duty Cycle
14 – 38 V
OM-477 Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3-2. Dimensions, Weights, And Operating Angles
Dimensions
Height
48-3/4 in (1238 mm)
24-5/8 in (625 mm)
64-1/2 (1638 mm)
62 in (1575 mm)
Width
Engine End
L
Depth
Y
Y
Do not exceed tilt angles or engine could
be damaged or unit could tip.
A
B
C
D
E
F
Do not move or operate unit where it could
tip.
59-1/8 in (1502 mm)
46-1/4 in (1175 mm)
34-3/4 in (883 mm)
26-15/16in (684) mm)
9-1/2 in (241 mm)
2-7/8 in (73 mm)
B
A
C
33°
E
G
H
J
D
33°
20°
20°
7/8 in (22 mm)
G
H
F
23-1/4 in (591 mm)
24-5/8 in (625 mm)
J
K
K
21/32 in
(16.7 mm) Dia.
12 Holes
L
ST-154 859
angles_1 8/99
Weight
1390 lb (631 kg)
3-3. Fuel Consumption
The curve shows typical fuel use
under weld or power loads.
SB-114 553-A
OM-477 Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
3-4. Duty Cycle And Overheating
Duty Cycle is percentage of 10 min-
utes that unit can weld at rated load
without overheating.
Y
Exceeding duty cycle can
damage unit and void
warranty.
60% Duty Cycle At 350 Amperes
100% Duty Cycle At 300 Amperes
6 Minutes Welding
4 Minutes Resting
Continuous Welding
rduty1 5/95 – SB-111 076-A
3-5. AC Auxiliary Power
The ac power curve shows the aux-
iliary power in amperes available at
the 120 and 240 volt receptacles.
rsb3.1 2/92 – ST-109 365-C
OM-477 Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
3-6. Optional AC Power Plant Curves
The ac power curves show the aux-
iliary power in amperes available at
the single-phase 120/240 volt or
three-phase240 volt terminals.
A. 8.5 KVA/KW Single-Phase Auxiliary Power Plant
(No Weld Load)
280
260
240
220
200
180
0
20
40
60
80
100
AC AMPERES
B. 12.5 KVA/KW Three-Phase Auxiliary Power Plant
(No Weld Load)
280
260
240
220
200
180
0
10
20
30
40
50
60
70
AC AMPERES
rsb13.1 12/94 - ST-111 118-D / ST-112 449-B
OM-477 Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
3-7. Volt-Ampere Curves
The volt-ampere curve shows the
minimum and maximum voltage
and amperage output capabilities of
the welding generator. Curves of all
other settings fall between the
curves shown.
A. CC/DC (Standard)
100
Ranges: 190–Max
110–270
80
60
40
20
0
85–210
55–110
Min–65
0
100
200
300
500
600
700
400
DC Amperes
B. CC/AC (Models with Optional Polarity/AC Selector Switch)
100
80
60
40
20
0
0
100
200
300
400
500
600
700
AC Amperes
C. CV/DC (Models with Optional CV-3 Module)
rsb13.1 12/94 – ST-184 477-A / ST-184 475-A / ST-184 480-A
OM-477 Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4 – INSTALLATION
4-1. Installing Welding Generator
Movement
Airflow Clearance
Location
18 in
(460 mm)
Y
Do Not Lift Unit From End
18 in
(460 mm)
18 in
(460 mm)
OR
OR
18 in
(460 mm)
18 in
(460 mm)
Grounding
3
Y
Always ground generator frame to ve-
hicle frame to prevent electric shock
and static electricity hazards.
1
4
GND/PE
1
2
3
4
Generator Base
Metal Vehicle Frame
Equipment Grounding Terminal
Grounding Cable
OR
Use #10 AWG or larger insulated copper wire.
Electrically bond generator frame to
vehicle frame by metal-to-metal
contact.
Y
If unit does not have GFCI receptacles,
use GFCI-protected extension cord.
2
2
install1 12/99 – Ref. ST-800 652 / Ref. ST-800 477-A / ST-158 936-A / S-0854
4-2. Connecting The Battery
Tools Needed:
1/2 in
Y
Connect
Negative (–)
Cable Last
+
–
Ref. ST-138 751-B / Ref. ST-191 898 / Ref. S-0756-C
4-3. Installing Muffler
Y
Y
Stop engine and let cool.
Do not blow exhaust toward
air cleaner or air intake.
Tools Needed:
1/2 in
muff1 4/96 – ST-154 088-B / Ref. ST-191 898
OM-477 Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
4-4. Engine Prestart Checks
Check all fluids daily. Engine must
be cold and on a level surface.
. This unit has a low oil pressure
shutdown switch. However,
some conditions may cause
engine damage before the en-
gine shuts down. Check oil lev-
el often and do not use the oil
pressure shutdown system to
monitor oil level.
1/2 in
(13 mm)
Full
Gasoline
Full
1
2
Carburetor Heat Selector Pipe
Manifold
Turn pipe toward manifold in cold
weather and away from manifold in
warm weather.
Capacity:
9 qt (8.5 L)
3
Fuel
Add fresh fuel before starting
engine the first time (see mainte-
nance label for specifications). Fill
fuel tank up to 1/2 in. (13 mm) from
top to allow room for expansion.
Open fuel shut-off valve. Check fuel
level on a cold engine before use
each day.
4
Oil
After fueling, check oil with unit on
level surface. If oil is not up to full
mark on dipstick, add oil (see main-
tenance label).
5
Coolant
Add coolant if level is below bottom
of radiator filler neck.
Engine coolant is a mixture of water
and ethylene glycol base anti-
freeze. Add anti-freeze to mixture if
using unit in temperatures below 0°
F (–18° C).
Keep radiator, air intake, and cool-
ing fins clean and free of dirt.
Y
Incorrect engine tempera-
ture can damage engine. Do
not run engine without a
properly working 180°F
(80°C) thermostat and a 7 psi
(48 kPa) radiator cap.
Full
.
T
o
i
m
p
r
o
v
e
c
o
l
d
w
e
a
t
h
e
r
starting:
Keep battery in good condition.
Store battery in warm area off
concrete surface.
Top View
2
1
Use correct grade oil for cold
weather.
Above
40°F (4°C)
Below
40°F (4°C)
Tools Needed:
5/16 in
ST-801 026-A / Ref. ST-159 727-C / Ref. ST-159 728-A
OM-477 Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
4-5. Connecting To Weld Output Terminals
Open left side door.
Bracket
Route cables through bracket.
1
3
2
Positive (+) Weld Output
Terminal
2
3
Negative (–) Weld Output Ter-
minal
For Stick welding Direct Current
Electrode Positive (DCEP), con-
nect work cable to (–) terminal and
electrode holder cable to (+)
terminal.
For Direct Current Electrode Nega-
tive (DCEN), reverse cable
connections.
Left Side
If equipped with optional polarity
switch, connect electrode holder
cable to Electrode (–) terminal and
work cable to Work (+) terminal.
For MIG and FCAW welding with
CV option, connect work cable to
(–) terminal and wire feeder cable to
(+) terminal
Close door.
1
Tools Needed:
3/4 in
ST-800 162-A
4-6. Selecting Weld Cable Sizes
Total Cable (Copper) Length In Weld Circuit Not Exceeding
150 ft
(45 m)
200 ft
(60 m)
250 ft
(70 m)
300 ft
(90 m)
350 ft
(105 m)
400 ft
(120 m)
100 ft (30 m) Or Less
10 – 60% 60 – 100% Duty
Welding
Amperes
10 – 100% Duty Cycle
Duty Cycle
Cycle
100
150
200
250
300
350
400
500
4
3
4
4
3
1
2
1
1/0
3/0
1/0
3/0
3
2
1/0
2/0
3
2
1
1/0
2/0
3/0
4/0
4/0
2-2/0
2/0
3/0
4/0
4/0
2
1
1/0
2/0
3/0
3/0
4/0
3/0
4/0
2-2/0
2-3/0
2-3/0
2-4/0
3-3/0
2-2/0
2-3/0
2-4/0
2-4/0
3-3/0
1
1/0
2/0
2/0
3/0
4/0
2-2/0
2-3/0
2-3/0
2-4/0
1/0
1/0
2/0
2-2/0
2-2/0
2-3/0
*Weld cable size (AWG) is based on either a 4 volts or less drop or a current density of at least 300 circular mils per ampere. Contact your
2
distributor for the mm equivalent weld cable sizes.
S-0007-E
OM-477 Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
4-7. Remote 14 Receptacle RC3 Information (Optional, See Section 4-8)
Socket*
Socket Information
A
24 volts ac. Protected by circuit
breaker CB4.
B
I
Contact closure to A completes 24
volts ac contactor control circuit.
115 volts ac. Protected by circuit
breaker CB3.
A
J
K
I
B
C
J
Contact closure to I completes 115
volts ac contactor control circuit.
L
N
H
M
D
G
G
C
Circuit common for 24 and 115 volts ac
circuits.
F
E
0 to +10 volts dc output to remote
control.
D
E
Remote control circuit common.
A/V
0 to +10 volts dc input command signal
from remote control.
Ref. ST-159 730-A
K
Chassis common.
*The remaining sockets are not used.
4-8. Terminal Strip 3T Connections (Optional)
Y
Stop engine.
If remote control plug does not fit in
receptacle RC3, wire cord directly
to terminal strip 3T.
Y
Do not connect to Remote 14
receptacleRC3 and terminal
strip 3T at the same time. Use
only one remote control
method.
Open right side door.
1
2
Cover
Terminal Strip 3T
Connect leads to 3T using terminal
information shown in Section 4-7.
Reinstall cover. Close door.
2
1
Tools Needed:
Ref. ST-139 670-B / ST-185 316 / Ref. ST-191 898
OM-477 Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 5 – OPERATING WELDING GENERATOR
5-1. Front Panel Controls (See Section 5-2)
3
4
5
1
2
6
7
17
16
15
14
13
11
10
9
8
()
12
Ref. ST-159 730-A / Ref. ST-191 898
OM-477 Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
5-2. Description Of Front Panel Controls (See Section 5-1)
nected to receptacle RC3 or terminal strip 3T In Run position, engine runs at weld/power
.
T
h
i
s
u
n
i
t
h
a
s
a
m
a
x
O
C
V
c
o
n
t
r
o
l
c
i
r
c
u
i
t
(see Sections 4-7 and 4-8).
speed. In Run/Idle position, engine runs at idle
speed at no load and weld speed with load ap-
plied. Turn to run position if using optional aux-
iliary power plant.
that resets Amperage/Voltage Adjust
Control R1 to maximum when the arc
breaks. When an arc is struck, weld out-
put control returns to the R1 front panel or
combination front panel/remote control
setting. The Amperage/Voltage Adjust
control adjusts amperage only when
constant current (CC) welding and does
not adjust open-circuit voltage. The max
OCV control circuit does not function
when constant voltage (CV) welding
(optional).
Y
Weld output terminals are energized
when Output (Electrode) switch is On
(Hot) and engine is running.
To Start: Pull choke out. Turn Engine Control
switch to Start while pressing Shutdown
switch. Release Engine Control switch when
engine starts, then release Shutdown switch
and push choke in.
For weld output, place switch in the On (Hot)
position. Open-circuit voltage is present at the
weld output terminals whenever engine is run-
ning.
For remote output control, place switch in Re-
mote position. Open-circuit voltage is present
at the weld output terminals when remote con-
tactor switch is closed.
. If the engine does not start, let engine
come to a complete stop before attempt-
ing restart.
1
Ampere Range Switch
5
Process Switch (Optional)
To Stop: turn Engine Control switch to Off
Y
Do not switch under load.
position.
Use switch to select Stick or MIG (CV) weld
output. Use Stick for Stick (SMAW) welding.
Use MIG (CV) for wire feed processes (MIG,
FCAW). If using MIG (CV), place Ampere
Range switch in maximum position. To en-
sure wire feeder reliability and improve arc
starting, unit does not run at idle speed
when operated in MIG (CV) mode.
Use switch to select weld amperage range.
For most welding applications, use lowest am-
perage range possible to help prevent arc out-
ages. When using MIG (CV) mode (optional),
place switch in maximum position.
11 Engine Hour Meter
12 Polarity And AC Selector Switch
(Optional)
Y
Do not switch under load.
2
Amperage/Voltage Adjust Control
13 Battery Charging Warning Light
Light goes on if battery is not charging.
Control adjusts amperage within range se-
lected by Ampere Range switch. Weld output . Place Process switch in Stick position
14 Low Oil Pressure/High Engine Tempera-
ture Warning Light
would be 148 A DC with controls set as shown
(50% of 85 to 210 A).
when using optional auxiliary power plant.
6
7
8
DC Voltmeter (Optional)
Light goes on if oil pressure is low or coolant
temperature is high.
3
Amperage/Voltage Adjust Switch
(Optional)
DC Ammeter (Optional)
Y
Stop engine and fix trouble if either
warning light goes on.
Magnetic Shutdown Switch
Use switch to select front panel or remote am-
perage control (see Section 5-3).
Use switch during start-up to bypass engine
shutdown system. System stops engine if oil
pressure is too low or coolant temperature is
too high.
15 Fuel Gauge
For front panel control, place switch in Panel
position. For remote control, place switch in
Remote position and connect remote control
to Remote 14 receptacle RC3 or terminal strip
3T.
16 Engine Temperature Gauge (Optional)
Normal temperature is 180 - 200° F (81 - 93°
C). Stop engine if temperature exceeds 240°
F (116° C).
9
Choke Control
Use choke to change engine air-fuel mix.
10 Engine Control Switch
4
Output (Electrode) Control Switch
(Optional)
17 Engine Oil Pressure Gauge (Optional)
Use switch to start engine, select engine Normal pressure is 40 psi (276 kPa). Stop en-
gine if pressure is below 8 psi (55 kPa).
Use switch to control remote contactor con- speed, and stop engine.
OM-477 Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
5-3. Remote Control (Optional)
Y
Weld output terminals are
energized when Output
(Electrode) switch is On
(Hot) and engine is running.
1
Remote 14 Receptacle RC3
Connect optional remote control to
RC3 (see Section 4-7).
1
Example: Combination remote amperage control
In Example:
Range = 85 to 210 A DC
Min = 85 A DC
Percentage of Range = 50%
Max = 148 A DC (50% of 85 to 210)
OR
Max (148 A DC)
Min (85 A DC)
Set switches
Set range
Set percentage
Adjust optional remote control
S-0774 / Ref. ST-159 730-A / Ref. ST-191 898
OM-477 Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 6 – OPERATING AUXILIARY EQUIPMENT
6-1. 120 Volt Duplex And Optional GFCI Receptacles
Y
If unit does not have GFCI re-
ceptacles, use GFCI-pro-
tected extension cord.
1
2
3
120 V 15 A AC Receptacle
RC1
120 V 15 A AC Receptacle
RC2
120 V 15 A AC GFCI Recep-
tacles GFCI1 And GFCI2
(Optional)
1
2
Receptacles supply 60 Hz single-
phase power at weld/power speed.
4
5
Circuit Breaker CB1
Circuit Breaker CB2
4
5
CB1 protects RC1/GFCI1 and CB2
protects RC2/GFCI2 from over-
load. If CB1 or CB2 opens, the re-
ceptacle does not work. Press but-
ton to reset circuit breaker.
.
I
f
a
c
i
r
c
u
i
t
b
r
e
a
k
e
r
c
o
n
t
i
n
u
e
s
t
o
open, contact
a
Factory
Authorized Service Agent.
If a ground fault is detected, the
GFCI Reset button pops out and
the circuit opens to disconnect the
faulty equipment. Check for dam-
aged tools, cords, plugs, etc. con-
nected to the receptacle. Press but-
ton to reset receptacle and resume
operation.
. At least once a month, run en-
gine at weld/power speed and
press Test button to verify
GFCI is working properly.
Maximum output from each duplex
receptacle is 1.8 kVA/kW, and 3
kVA/kW from all receptacles.
Auxiliary power is not affected by
weld output.
EXAMPLE: If 15 A is drawn from
RC1, only 10 A is available at RC2:
(120 V x 15 A) + (120 V x 10 A) = 3.0
kVA/kW
3
Ref. ST-191 898
OM-477 Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
6-2. 240 Volt Duplex Receptacle (Optional)
Y
If unit does not have GFCI re-
ceptacles, use GFCI-pro-
tected extension cord.
1
240 V 15 A AC Receptacle
RC1
Receptacle supplies 60 Hz single-
phase power at weld/power speed.
Maximum output is 3 kVA/kW.
1
2
3
Circuit Breaker CB1
Circuit Breaker CB2
CB1 and CB2 protect the recep-
tacles from overload. If CB1 or CB2
opens, the 240 V receptacle and
half of the 120 V receptacle does
not work. 120 volts may still be
present at the 240 V receptacle.
Press button to reset circuit
breaker.
2
3
.
I
f
a
c
i
r
c
u
i
t
b
r
e
a
k
e
r
c
o
n
t
i
n
u
e
s
t
o
open, contact
a
Factory
Authorized Service Agent.
Combined output of all receptacles
is 3 kVA/kW. Auxiliary power is not
affected by weld output.
EXAMPLE:If 10 A is drawn from the
240 V receptacle, only 5 A is avail-
able at the 120 V receptacle:
(240 V x 10 A) + (120 V x 5 A) = 3.0
kVA/kW
Ref. ST-181 711-A / Ref. ST-174 408
OM-477 Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
6-3. Connecting Optional Auxiliary Power Plant
Y
Y
Stop engine.
Power and weld outputs are
live at the same time. Discon-
nect or insulate unused
cables.
. Have qualified person install ac-
cording to circuit diagram and
Auxiliary Power Guidelines
Booklet (M176 712).
. Place optional Process switch
in Stick position when using op-
tional auxiliary power plant.
Front
Remove junction box cover.
11
10
1
2
3
4
5
6
7
8
Lead 93
Lead 92
Lead 91
Lead 90 (Neutral)
Isolated Neutral Terminal
Jumper Lead 42
Grounding Terminal
1
2
F3
F2
F1
240V
240V
240V 240V
3
Lead 42 (Circuit Grounding
Lead)
120V 120V
1
Jumper 42 is connected to lead 90 at
factory. Jumper 42 may be discon-
nected from neutral to meet applica-
ble electrical codes.
3
9
Lead 42 connects to front panel
Ground stud.
9
User-Supplied Leads
10 Load Terminals
4
5
6
7
8
Connect leads to terminals.
11 Fuses F1, F2, And F3
F1, F2, and F3 protect each load line
from overload.
. Set Engine Control switch to
Run when using auxiliary
power.
Single
Phase
1
Three
Phase
3
AC
Output
Volts
120/240
240
93
91
Amps
35
30
KVA/KW
Frequency
8.5
12.5
60 Hz
Engine Speed
1850 RPM
Max. Fuse Size
45 Amperes
90
92
Lead 42 connects to GROUND stud on
front of unit.
Jumper 42 is connected to 90 at factory.
Tools Needed:
Ref. S-185 000–A
OM-477 Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7 – MAINTENANCE AND TROUBLESHOOTING
Follow the storage procedure in the engine owner’s manual if the unit will not be
used for an extended period.
NOTE
7-1. Routine Maintenance
Y
Stop engine before maintaining.
Recycle
engine
fluids.
.
S
e
e
a
l
s
o
E
n
g
i
n
e
M
a
n
u
a
l
a
n
d
M
a
i
n
t
e
n
a
n
c
e
Label. Service engine more often if used in
severe conditions.
*
To be done by Factory Authorized Service
Agent.
8 h
Wipe up spills.
Check fluid levels.
See Section 4-4.
OIL
Full
50 h
Clean air filter.
See Section 7-3.
Clean and tighten
weld terminals.
100 h
Check
air
Change oil. See
Section 7-5.
Change oil filter.
See Section 7-5.
cleaner hoses
for cracks and
loose clamps.
Replace fuel filter.
See Section 7-6.
Clean and tighten battery
connections.
200 h
250 h
Replace
unreadable
labels.
Check spark
plugs.
Check and clean
spark arrestor.
See Section 7-7.
500 h
Check valve clearance.*
Repair or replace
cracked cables.
1000 h
Blow out or
vacuum inside.
During heavy
service, clean
monthly.
Service welding generator
brushes and slip rings.
Service more often in dirty
conditions.*
Check
belt
tension.
1/2 in.
(13 mm)
Or
OM-477 Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
7-2. Maintenance Label
OM-477 Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
7-3. Servicing Air Cleaner
Y
Y
Stop engine.
Do not run engine without air
cleaner or with dirty element.
Clean or replace element if dirty or
damaged. Replace element yearly
or after six cleanings.
1
2
3
4
5
Dust Cap
Baffle
5
4
3
2
1
Element
Plastic Fins
Housing
To Clean air filter:
Wipe off cap and housing. Remove
cap and dump out dust. Wipe dust
from inside cap and housing with
damp cloth. Remove element and
reinstall cap.
Y
Do not clean housing with air
hose.
Clean element with compressed air
only. Keep nozzle at least 1 in (25
mm) from inside of element. Max. air
pressure: 100 psi (690 kPa). Do not
remove plastic fins. Replace ele-
ment if it has holes or damaged
gaskets.
Reinstall element and cap (cap
arrows pointing up).
Blow
Inspect
aircleaner1 6/96 – ST-153 929-B / ST-153 585 / Ref. ST-191 898 / Ref. S-0698-B
7-4. Overload Protection
Y
Stop engine.
. If any fuse or circuit breaker
continues to open, contact Fac-
tory Authorized Service Agent.
1
Magnetic Shutdown
Switch MS1
2
Fuse F (See Parts List)
Fuse F protects magnetic shutdown
switch MS1. If fuse F opens, the
engine stops.
Check fuse and replace if open.
3
4
Circuit Breaker CB3 (Optional)
Circuit Breaker CB4 (Optional)
CB3 protects the 115 volt ac output
and CB4 protects the 24 volt ac out-
put to optional Remote 14 recep-
tacle RC3 and terminal strip 3T. If a
circuit breaker opens, 24 or 115
volts ac output stops.
1
3
4
Press button to reset breaker.
2
Tools Needed:
Ref. ST-159 730-A / Ref. ST-191 898
OM-477 Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
7-5. Changing Engine Oil And Filter
Y
1
Stop engine and let cool.
Standard Oil Filter
2
Optional Remote Oil Filter
3
Optional Remote Oil Filter
Hoses And Adapter
4
5
Oil Drain Plug
Oil Fill Cap
Change filter according to engine
manual.
Install optional remote oil filter if lo-
cation makes it difficult to change
standard filter.
1
. The remote oil filter requires
extra oil to fill the hoses. Keep
oil up to full mark on dipstick.
4
5
3
Tools Needed:
2
7/8 in
Ref. ST-159 727-B / Ref. ST-159 728-A / Ref. ST-191 898
OM-477 Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
7-6. Changing Fuel Filter
Y
1
Stop engine and let cool.
Fuel Shutoff Valve
Fuel Line
2
3
Fuel Filter
To replace filter, close valve and re-
move clamps and filter. Install new
filter and clamps. Inspect line and
replace if cracked or worn. Wipe up
any spilled fuel. Open valve.
Start engine and check for leaks.
Y
Stop engine, tighten connec-
tions as necessary, and wipe
up spilled fuel.
Close door.
1
2
3
2
Tools Needed:
Ref. ST-191 898 / Ref. ST-159 727-C
7-7. Inspecting And Cleaning Optional Spark Arrestor Muffler
Y
1
Stop engine and let cool.
Spark Arrestor Muffler
Cleanout Plug
2
Remove plug and remove any dirt
covering cleanout hole.
3
Exhaust Pipe
Start engine and run at idle speed to
blow out cleanout hole. If nothing
blows out of hole, briefly cover end
of exhaust pipe with fireproof
material.
3
2
1
Y
Stop engine and let cool.
Reinstall cleanout plug.
Tools Needed:
3/8 in
ST-800 722 / Ref. ST-191 898
OM-477 Page 28
Download from Www.Somanuals.com. All Manuals Search And Download.
7-8. Adjusting Engine Weld/Power Speed
.
G
o
v
e
r
n
o
r
s
e
n
s
i
t
i
v
i
t
y
m
a
y
r
e
-
quire adjustment if engine
speed is adjusted (see Section
7-10).
1850 rpm
(max)
If linkage binds, loosen socket
nuts and turn sockets until link-
age works smoothly. Tighten
nuts.
After tuning engine, check engine
no load speed with a tachometer
(see table for no load speeds). If
necessary, adjust speed as follows:
7
11
10
1
2
3
4
5
Socket Nut
Governor Linkage Rod
Lock Nut
Socket
9
Governor Arm
Rod length should be 3-1/4 in (83
mm) between lock nuts. To adjust,
remove socket from arm and loos-
en lock nut. Turn socket to adjust
length. Tighten nut and reattach
socket to arm.
1/16 in
(1.6 mm)
8
6
6
7
8
Carburetor
Throttle Stop Plate
Throttle Stop
Clearance between plate and stop
should be 1/16 in (1.6 mm). To ad-
just clearance, proceed as follows:
9
Linkage Pivot Arm
10 Linkage Socket
11 Lock Nut
Remove socket at arm and loosen
lock nut. Turn socket to adjust
clearance. Reattach socket and
tighten nut.
1
4
3-1/4 in
(83 mm)
Start engine and run until warm.
Turn Engine Control switch to Run
position.
3
2
5
12 Governor Speed Screw
13 Lock Nut
Loosen nut. Turn screw until engine
runs at weld/power speed.
Y
Stop engine.
Close door.
13
12
Tools Needed:
3/8, 7/16 in
Ref. ST-801 179 / Ref. ST-800 159-C / Ref. ST-800 161
OM-477 Page 29
Download from Www.Somanuals.com. All Manuals Search And Download.
7-9. Adjusting Engine Idle Speed
Start engine. Place Engine Control
Switch in Run/Idle position.
1
2
3
4
Solenoid Bracket Screws
Throttle Arm
2
5
Idle Speed Screw
Throttle Stop
1250 rpm
Loosen bracket screws and move
arm so screw touches stop. Do not
release arm. Turn idle speed screw
to obtain 550 rpm.
5
Idle Mixture Screw
Turn mixture screw counterclock-
wise until engine falters, then turn
screw clockwise until engine runs
smoothly.
1
Turn idle speed screw to obtain
1250 rpm.
6
7
Solenoid
Plunger
6
Slide solenoid inside bracket so
plungerbottoms in solenoid. If nec-
essary, shim solenoid/bracket to
prevent linkage from binding. Do
not readjust idle speed screw when
adjustingsolenoid.
7
3
Right Side
Tighten bracket screws. Release
throttle arm. Recheck idle speed
and readjust if necessary.
Tools Needed:
Y
Stop engine.
Close door.
4
1/4 in
Ref. ST-115 155-A
7-10. Adjusting Governor Sensitivity
. Governor sensitivity may re-
quire readjustment if weld
speed is adjusted. Weld speed
must be readjusted if sensitivity
is adjusted.
Be sure carburetor and link-
ages are adjusted properly be-
fore adjusting sensitivity.
3
Start engine. Apply and remove
load.
1
2
3
Locking Nuts
2
1
Sensitivity Adjustment Screw
Governor Spring
If engine is slow to pick up load or
rpm drops under load, adjust spring
tension as follows:
Loosen top nut and tighten bottom
nut to move screw down. Tighten
nuts.
If engine hunts with or without load,
adjust spring tension as follows:
Loosen bottom nut and tighten top
nut to move screw up. Tighten nuts.
Y
Stop engine.
Close door.
Tools Needed:
1/2 in
Ref. ST-115 155-A / Ref. ST-159 728-A
OM-477 Page 30
Download from Www.Somanuals.com. All Manuals Search And Download.
7-11. Adjusting Optional High Altitude Carburetor
Y
A too lean air-fuel mixture
can damage valves. Do not
adjust main adjustment
screw so air-fuel mixture is
too lean.
Carburetorcan be equipped with an
adjustable main jet for operation
above 4000 ft (1219 m). Adjust car-
buretor as follows:
Start engine and apply nearly full
load to welding generator.
1
2
Main Adjustment Screw
Lock Nut
Loosen nut. Turn screw in until en-
gine falters (lean air-fuel mixture).
Turn screw out until engine runs
smoothly, then turn screw out an
additional1/4 turn. Tighten nut.
Y
Stop engine.
1
2
Close door.
Tools Needed:
1/2 in
Ref. ST-159 727-B / Ref. ST-115 155-A
7-12. Troubleshooting
A. Welding
Trouble
Remedy
No weld output.
Check control settings.
Place optional Output (Electrode) Control switch in On (Hot) position, or move switch to Remote posi-
tion and connect remote contactor to Remote 14 receptacle RC3 or terminal strip 3T (see Sections
4-7, 4-8, and 5-1).
Check and secure connections to optional Remote 14 receptacle RC3 or terminal strip 3T (see Sec-
tions 4-7 and 4-8).
Disconnect equipment from 120 volt ac receptacles during start-up.
Have Factory Authorized Service Agent check brushes and slip rings, and field current regulator board
PC1.
Erratic weld output.
Check and tighten connections inside and outside unit.
Use dry, properly-stored electrodes.
Remove excessive coils from weld cables.
Be sure connection to work piece is clean and tight.
Have Factory Authorized Service Agent check brushes and slip rings.
OM-477 Page 31
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble
Remedy
Low or high weld output.
Check control settings.
Place optional Process switch in correct position (see Section 5-1).
Check engine weld/power speed, and adjust if necessary (see Section 7-8).
Have Factory Authorized Service Agent check field current regulator board PC1.
Place optional Process switch in correct position.
Low open-circuit voltage.
Check engine weld/power speed, and adjust if necessary (see Section 7-8).
Have Factory Authorized Service Agent check field current regulator board PC1 and optional CV-3 regu-
lator board PC2.
Maximum weld output only in each am- Have Factory Authorized Service Agent check Amperage/Voltage Adjust control R1, capacitor C8,
pere range.
diode D9, integrated rectifier SR4, control relay CR3, field current regulator board PC1, and optional
CV-3 regulator board PC2.
No CV weld output (units with remote Check connections to Remote 14 receptacle RC3 and terminal strip 3T (see Sections 4-7 and 4-8).
control or CV-3 option only).
Repair or replace remote control device.
Have Factory Authorized Service Agent check connector board PC5 and connections.
Wire feeder does not work (models with Reset circuit breaker CB3 and/or CB4 (see Section 7-4).
CV-3 option).
Check connections to Remote 14 receptacle RC3 and terminal strip 3T (see Sections 4-7 and 4-8).
Repair or replace wire feeder.
No amperage control (or voltage control Place Amperage/Voltage Adjust switch in correct position.
on models with CV-3 option).
Check connections to Remote 14 receptacle RC3 and terminal strip 3T (see Sections 4-7 and 4-8).
Repair or replace remote control device.
Have Factory Authorized Service Agent check optional CV-3 regulator board PC2.
Low CV weld output (models with CV-3 Set Ampere Range switch to highest range.
option).
Min or max CV weld output only (models Check position of Amperage/Voltage Adjust control and Amperage/Voltage Adjust switch.
with CV-3 option).
Repair or replace remote control device.
Have Factory Authorized Service Agent check optional CV-3 regulator board PC2.
B. Auxiliary Power
Trouble
Remedy
No output at auxiliary power ac
receptacles.
Reset circuit breaker CB1 and/or CB2 (see Section 6-1).
Disconnect equipment from receptacles during start-up.
Have Factory Authorized Service Agent check brushes and slip rings.
No or low output at optional auxiliary
power plant.
Place optional Output (Electrode) Control switch in On (Hot) position, or move switch to Remote posi-
tion and connect remote contactor to Remote 14 receptacle RC3 or terminal strip 3T (see Sections
4-7, 4-8, and 5-1).
Place optional Amperage/Voltage Adjust switch in Panel position, or move to Remote position and
connect remote amperage control to Remote 14 receptacle RC3 or terminal strip 3T (see Sections
4-7, 4-8, and 5-1)
Place optional remote amperage control in maximum position (see Section 5-3).
Place optional Process switch in Stick position (see Section 5-1).
Check fuses F1, F2, and F3 and replace as necessary (see Section 6-3).
Check engine weld/power speed, and adjust if necessary (see Section 7-8).
OM-477 Page 32
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble
Remedy
Have Factory Authorized Service Agent check brushes and slip rings, and field current regulator board
PC1.
High or low voltage at auxiliary power
ac receptacles.
Check engine weld/power speed, and adjust if necessary (see Section 7-8).
Have Factory Authorized Service Agent check field current resistor R3.
High output at optional auxiliary power Check engine weld/power speed, and adjust if necessary (see Section 7-8).
plant.
Have Factory Authorized Service Agent check field current regulator board PC1.
C. Engine
Trouble
Remedy
Engine does not start.
Check fuel level. Open fuel shutoff valve (see Section 4-4).
Check battery and replace if necessary (see Section 4-2).
Check oil and water levels. Automatic shutdown system stops engine if oil pressure gets too low or
coolant temperature gets too high (see Section 4-4).
Check Engine Control switch, and replace if necessary.
Check Magnetic Shutdown switch MS1 fuse F and replace if open (see Section 7-4).
See engine manual.
Have Factory Authorized Service Agent check engine charging system.
Clean battery, terminals, and posts with baking soda and water solution; rinse with clear water.
Periodically recharge battery (approximately every 3 months).
Replace battery (see Section 4-2).
Battery discharges between uses.
Have Factory Authorized Service Agent check engine charging system.
Check Engine Control switch, and replace if necessary.
Engine idles, but does not come up to
weld speed.
Have Factory Authorized Service Agent check idle module and current transformer CT1.
Engine does not run at idle speed.
Move Optional Process switch to Stick position (see Section 5-1). Unit does not run at idle speed
when operated in MIG (CV) mode.
Engine slowly stopped and cannot be
restarted.
Check fuel level. Open fuel shutoff valve (see Section 4-4).
Check oil and water levels. Automatic shutdown system stops engine if oil pressure gets too low or
coolant temperature gets too high (see Section 4-4).
See engine manual.
OM-477 Page 33
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
OM-477 Page 34
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 8 – ELECTRICAL DIAGRAMS
193 965-A
Figure 8-1. Circuit Diagram For Welding Generator For Standard Models
OM-477 Page 35
Download from Www.Somanuals.com. All Manuals Search And Download.
Figure 8-2. Circuit Diagram For Welding Generator With Welders And Deluxe Package Options
OM-477 Page 36
Download from Www.Somanuals.com. All Manuals Search And Download.
193 967-A
OM-477 Page 37
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9 – AUXILIARY POWER GUIDELINES
9-1. Selecting Equipment
1
2
3
Auxiliary Power Receptacles
– Neutral Bonded To Frame
3-Prong Plug From Case
Grounded Equipment
2-Prong Plug From Double
Insulated Equipment
1
2
3
Be sure equipment
has this symbol
and/or wording.
OR
aux_pwr 2/99 – Ref. ST-159 730 / ST-800 577
9-2. Grounding Generator To Truck Or Trailer Frame
1
2
3
Generator Base
Metal Vehicle Frame
Equipment Grounding
Terminal
4
Grounding Cable
Use #10 AWG or larger insulated
copper wire.
Y
If unit does not have GFCI re-
ceptacles, use GFCI-pro-
tected extension cord.
3
4
1
GND/PE
2
OR
Electrically bond generator
frame to vehicle frame by
metal-to-metalcontact.
2
S-0854
OM-477 Page 38
Download from Www.Somanuals.com. All Manuals Search And Download.
9-3. Grounding When Supplying Building Systems
1
2
EquipmentGrounding
Terminal
1
2
Grounding Cable
GND/PE
Use #10 AWG or larger insulated
copper wire.
3
Ground Device
Y
Ground generator to system
earth ground if supplying
power to a premises (home,
shop, farm) wiring system.
Use ground device as stated
in electrical codes.
2
3
ST-800 576-B
9-4. How Much Power Does Equipment Require?
1
Resistive Load
3
A light bulb is a resistive load and
requires a constant amount of pow-
er.
VOLTS 115
AMPS 4.5
Hz 60
2
1
2
Non-Resistive Load
Equipmentwith a motor is a non-re-
sistive load and requires approxi-
mately six times more power while
starting the motor than when run-
ning (see Section 9-8).
3
3
Rating Data
Rating shows volts and amperes,
or watts required to run equipment.
AMPERES x VOLTS = WATTS
EXAMPLE 1: If a drill uses 4.5 amperes at 115 volts, calculate its running power
requirementin watts.
4.5 A x 115 V = 520 W
The load applied by the drill is 520 watts.
EXAMPLE 2: If three 200 watt flood lamps are used with the drill from Example 1,
add the individual loads to calculate total load.
(200 W + 200 W + 200 W) + 520 W = 1120 W
The total load applied by the three flood lamps and drill is 1120 watts.
S-0623
OM-477 Page 39
Download from Www.Somanuals.com. All Manuals Search And Download.
9-5. Approximate Power Requirements For Industrial Motors
Industrial Motors
Rating
Starting Watts
Running Watts
Split Phase
1/8 HP
1/6 HP
1/4 HP
1/3 HP
1/2 HP
1/3 HP
1/2 HP
3/4 HP
1 HP
800
1225
1600
2100
3175
2020
3075
4500
6100
8200
10550
15900
23300
8100
23300
35000
46700
1000
1400
1850
2400
3500
300
500
600
700
875
Capacitor Start-Induction Run
720
975
1400
1600
2200
2850
3900
6800
2000
6000
8000
10700
400
1-1/2 HP
2 HP
3 HP
5 HP
Capacitor Start-Capacitor Run
1-1/2 HP
5 HP
7-1/2 HP
10 HP
1/8 HP
1/6 HP
1/4 HP
1/3 HP
1/2 HP
Fan Duty
550
650
800
1100
9-6. Approximate Power Requirements For Farm/Home Equipment
Farm/HomeEquipment
Rating
Starting Watts
Running Watts
Stock Tank De-Icer
1000
1650
3400
4400
2900
10500
1720
2575
4500
6100
8200
10550
15900
23300
8100
23300
35000
46700
3300
3150
4500
6100
3100
2150
3100
2100
3200
1000
650
Grain Cleaner
1/4 HP
1/2 HP
3/4 HP
Portable Conveyor
Grain Elevator
1000
1400
1100
2800
720
Milk Cooler
Milker (Vacuum Pump)
FARM DUTY MOTORS
Std. (e.g. Conveyors,
Feed Augers, Air
Compressors)
2 HP
1/3 HP
1/2 HP
3/4 HP
1 HP
975
1400
1600
2200
2850
3900
6800
2000
6000
8000
10700
1000
950
1-1/2 HP
2 HP
3 HP
5 HP
High Torque (e.g. Barn
1-1/2 HP
5 HP
Cleaners, Silo Unloaders,
Silo Hoists, Bunk Feeders)
7-1/2 HP
10 HP
1/2 HP
500 PSI
550 PSI
700 PSI
3-1/2 cu. ft. Mixer
High Pressure 1.8 Gal/Min
Washer 2 gal/min
2 gal/min
1400
1600
800
Refrigerator or Freezer
Shallow Well Pump
1/3 HP
1/2 HP
1/3 HP
1/2 HP
750
1000
800
Sump Pump
1050
OM-477 Page 40
Download from Www.Somanuals.com. All Manuals Search And Download.
9-7. Approximate Power Requirements For Contractor Equipment
Contractor
Rating
Starting Watts
Running Watts
Hand Drill
1/4 in
3/8 in
350
400
350
400
1/2 in
600
600
Circular Saw
Table Saw
6-1/2 in
7-1/4 in
8-1/4 in
9 in
500
500
900
900
1400
4500
6300
2500
1720
3900
5200
3000
6000
8200
10500
1100
1100
350
1400
1500
1800
1100
720
10 in
Band Saw
14 in
Bench Grinder
6 in
8 in
1400
1600
1000
1500
2200
2800
1100
1100
350
10 in
Air Compressor
1/2 HP
1 HP
1-1/2 HP
2 HP
Electric Chain Saw
Electric Trimmer
Electric Cultivator
1-1/2 HP, 12 in
2 HP, 14 in
Standard 9 in
Heavy Duty 12 in
1/3 HP
500
500
2100
400
700
Elec. Hedge Trimmer
Flood Lights
18 in
400
HID
125
100
Metal Halide
Mercury
Sodium
Vapor
313
250
1000
1400
1250
600
1000
200
Submersible Pump
Centrifugal Pump
Floor Polisher
400 gph
900 gph
3/4 HP, 16 in
1 HP, 20 in
1/2 HP
900
500
4500
6100
3150
4500
6100
1900
900
1400
1600
950
High Pressure Washer
3/4 HP
1400
1600
700
1 HP
55 gal Drum Mixer
Wet & Dry Vac
1/4 HP
1.7 HP
900
2-1/2 HP
1300
1300
OM-477 Page 41
Download from Www.Somanuals.com. All Manuals Search And Download.
9-8. Power Required To Start Motor
1
2
3
4
Motor Start Code
Running Amperage
Motor HP
4
AC MOTOR
VOLTS 230 AMPS 2.5
Hz 60
PHASE 1
2
1
3
CODE
HP
M
Motor Voltage
1/4
To find starting amperage:
Step 1: Find code and use table to
find kVA/HP. If code is not listed,
multiplyrunning amperage by six to
find starting amperage.
Step 2: Find Motor HP and Volts.
Step 3: Determine starting amper-
age (see example).
Welding generator amperage out-
put must be at least twice the
motor’s running amperage.
Single-Phase Induction Motor Starting Requirements
Motor Start
Code
G
H
J
K
L
M
N
P
KVA/HP
6.3
7.1
8.0
9.0
10.0
11.2
12.5
14.0
kVA/HP x HP x 1000
VOLTS
= STARTING AMPERAGE
EXAMPLE: Calculate the starting amperage required for a 230 V, 1/4
HP motor with a motor start code of M.
Volts = 230 HP = 1/4 Using Table, Code M results in kVA/HP = 11.2
11.2 x 1/4 x 1000
= 12.2 A
Starting the motor requires 12.2 amperes.
230
S-0624
9-9. How Much Power Can Generator Supply?
1
Limit Load To 90% Of
Generator Output
Always start non-resistive (motor)
loads in order from largest to small-
est, and add resistive loads last.
2
5 Second Rule
1
If motor does not start within 5
seconds, turn off power to prevent
motor damage. Motor requires
more power than generator can
supply.
2
Ref. ST-800 396-A / S-0625
OM-477 Page 42
Download from Www.Somanuals.com. All Manuals Search And Download.
9-10. Typical Connections To Supply Standby Power
1
2
3
Power Company Service
Meter
Main and Branch Overcurrent
Protection
Double-Pole, Double-Throw
Transfer Switch
Obtain and install correct switch.
Switch rating must be same as or
greater than the branch overcurrent
protection.
. Customer-supplied equipment is required if
generator is to supply standby power during
emergenciesor power outages.
4
Circuit Breakers or Fused
Disconnect Switch
1
240 V
Obtain and install correct circuit
breakers or switch.
120/240 Volt
5
Extension Cord
Select as shown in Section 9-11.
Generator Connections
120 V
60 Hz
Three-Wire
Service
120 V
6
Connect terminals or plug of ade-
quate amperage capacity to cord.
Follow all applicable codes and
safety practices.
2
3
Turn off or unplug all equipment
connected to generator before
starting or stopping engine. When
starting or stopping, the engine has
low speed which causes low volt-
age and frequency.
240 V
120 V
Load
120 V
7
Load Connections
4
7
CB
or
Item 4 is not necessary if circuit
protection is already present in
welding generator auxiliary
power output circuit.
F1
5
6
240 V
120/240 Volt
Single-Phase
Three-Wire
120 V
120 V
Generator Output
Connection
Ground
S-0405-A
OM-477 Page 43
Download from Www.Somanuals.com. All Manuals Search And Download.
9-11. Selecting Extension Cord (Use Shortest Cord Possible)
Cord Lengths for 120 Volt Loads
Y
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*
Current
(Amperes)
Load (Watts)
4
6
8
10
12
14
5
600
350 (106)
250 (76)
175 (53)
112 (34)
87 (26)
62 (19)
50 (15)
50 (15)
37 (11)
225 (68)
150 (46)
112 (34)
75 (23)
50 (15)
37 (11)
37 (11)
137 (42)
100 (30)
62 (19)
37 (11)
30 (9)
100 (30)
62 (19)
50 (15)
30 (9)
7
840
400 (122)
275 (84)
175 (53)
137 (42)
112 (34)
87 (26)
10
15
20
25
30
35
40
45
50
1200
1800
2400
3000
3600
4200
4800
5400
6000
400 (122)
300 (91)
225 (68)
175 (53)
150 (46)
125 (38)
112 (34)
100 (30)
87 (26)
75 (23)
62 (19)
62 (19)
50 (15)
*Conductor size is based on maximum 2% voltage drop
Cord Lengths for 240 Volt Loads
Y
If unit does not have GFCI receptacles, use GFCI-protected extension cord.
Maximum Allowable Cord Length in ft (m) for Conductor Size (AWG)*
Current
(Amperes)
Load (Watts)
4
6
8
10
12
14
5
1200
1680
2400
3600
4800
6000
7000
8400
9600
10,800
12,000
700 (213)
500 (152)
350 (107)
225 (69)
175 (53)
125 (38)
100 (31)
100 (31)
75 (23)
450 (137)
300 (91)
225 (69)
150 (46)
100 (31)
75 (23)
225 (84)
200 (61)
125 (38)
75 (23)
200 (61)
125 (38)
100 (31)
60 (18)
7
800 (244)
550 (168)
350 (107)
275 (84)
225 (69)
175 (53)
150 (46)
125 (38)
125 (38)
100 (31)
10
15
20
25
30
35
40
45
50
800 (244)
600 (183)
450 (137)
350 (107)
300 (91)
250 (76)
225 (69)
200 (61)
175 (53)
60 (18)
75 (23)
*Conductor size is based on maximum 2% voltage drop
OM-477 Page 44
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes
OM-477 Page 45
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10 – PARTS LIST
.
H
a
r
d
w
a
r
e
i
s
c
o
m
m
o
n
a
n
d
not available unless listed.
4
3
5
2
1
18
6
17
116
115
114
113
112
111
49
65
16
11
66
110
15
10
12
9
109
67
68
7
8
14
13
69
108
107
106
105
70
104
103
Fig 10-3
102
101
71
100
72
99
98
97
80
81
73
74
90
89
75
88
91
92
87
82
83
86
85 84
76
93
79
78
94
77
96
95
Figure 10-1. Main Assembly
OM-477 Page 46
Download from Www.Somanuals.com. All Manuals Search And Download.
20
19
21
22
30
31
23
25
24
29
28
27
26
25
32
33
62
63
64
61
34
35
36
37
38
40
60
47
Includes
Item 49
46
45
50
51
52
53
41
54
55
48
59
Fig 10-2
56
44
57
58
39
43
42
ST-115 004-P
OM-477 Page 47
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Figure 10-1. Main Assembly
Quantity
. . . 1 . . . . . . . . . . . . . . . . . . 134 771 . . . PLUG, protective .640sq . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 2 . . . . . . . . . . . . . . . . . . 184 677 . . . TANK, fuel (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 3 . . . . . . . . . . . . . . . . . . 182 022 . . . . CAP, fuel large . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . . . . . . . . . 146 357 . . . SENDER, fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 020 108 . . . FLANGE, fuel gauge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . . . . . . . . . . . . . 602 938 . . . FITTING, pipe galv plug sqhd .125NPT . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . . . . . . . . . . . . . . . 097 507 . . . STRIP, rbr adh back .125 x 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 7 . . . . . . . . . . . . . . . . . . 010 314 . . . VALVE, shut-off fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . . . . . . . 173 818 . . . FITTING, hose brs barbed elbow M 1/4tbg x 1/4NPT . . . . . . . . . . . . 1
. . . 9 . . . . . . . . . . . . . . . . . . 084 173 . . . CLAMP, hose .460-.545 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 10 . . . . . . . . . . . . . . . . . . 107 816 . . . HOSE, SAE .250 ID x .500 OD (order by ft) . . . . . . . . . . . . . . . . . . . . 2ft
. . . 11 . . . . . . . . . . . . . . . . . . 047 420 . . . FILTER, fuel in line .250 w/hose & clamps . . . . . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . . . . . . . . . . . . . . 017 479 . . . SEAL, weather lift eye . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 13 . . . . . . . . . . . . . . . . . . 188 235 . . . UPRIGHT, base center . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 14 . . . . . . . . . . . . . . . . . . 072 848 . . . TUBING, nprn .875 OD x 2.500 OD x 2.000 . . . . . . . . . . . . . . . . . . . . 4
. . . 15 . . . . . . . . . . . . . . . . . . 071 730 . . . TUBING, stl .875 OD x 12ga x 2.375 . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 16 . . . . . . . . . . . . . . . . . . 071 890 . . . RETAINER, mount eng/gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 17 . . . . . . . . . . . . . . . . . . 071 731 . . . WASHER, flat stl .656 ID x 2.250 OD . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 18 . . . . . . . . . . . . . . . . . . 601 945 . . . SCREW, .625-18 x 4.000 hexhd stl . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 19 . . . . . . . . . . . . . . . . . . 018 765 . . . AIR CLEANER, intake carb (consisting of) . . . . . . . . . . . . . . . . . . . . . . 1
. . . 20 . . . . . . . . . . . . . . . . . . 018 859 . . . . CAP, air cleaner intake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 21 . . . . . . . . . . . . . . . . . . 008 698 . . . . BAFFLE, dust cap . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 22 . . . . . . . . . . . . . . . . . . 021 117 . . . . NUT, stl wing .437-20 w/washer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 23 . . . . . . . . . . . . . . . . . *017 309 . . . . ELEMENT, air cleaner carb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 24 . . . . . . . . . . . . . . . . . . 000 272 . . . . CLAMP, air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 25 . . . . . . . . . . . . . . . . . . 031 868 . . . BRACKET, mtg air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 26 . . . . . . . . . . . . . . . . . . 010 875 . . . CLAMP, muffler 2.000dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 27 . . . . . . . . . . . . . . . . . . 105 740 . . . MUFFLER, exhaust engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 28 . . . . . . . . . . . . . . . . . . 035 968 . . . WASHER, flat rbr 3.625 ID x 5.875 OD . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 195 869 . . . CABLE TIE, 0-17.500 weather resistant . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 29 . . . . . . . . . . . . . . . . . . 108 487 . . . LABEL, warning falling equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 30 . . . . . . . . . . . . . . . . . +105 631 . . . COVER, top . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 057 359 . . . BLANK, snap-in nyl .375mtg hole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 31 . . . . . . . . . . . . . . . . . . 028 089 . . . DOOR, access radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 191 865 . . . BUMPER, door access radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 32 . . . . . . . . . . . . . . . . . . 089 343 . . . RIVET, nyl .250dia x 1.000 lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . 33 . . . . . . . . . . . . . . . . . . 004 130 . . . BRACKET, support door . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 34 . . . . . . . . . . . . . . . . . +089 510 . . . DOOR, side . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 114 793 . . . LABEL, engine maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 35 . . . . . . . . . . . . . . . . . . 158 610 . . . LABEL, electric shock and moving parts . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 36 . . . . . . . . . . . . . . . . . . 087 336 . . . LATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 087 341 . . . BUMPER, door 1.000 OD x .750 high . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 37 . . . . . . . . . . . . . . . . . . 197 464 . . . RADIATOR, w/shroud (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 38 . . . . . . . . . . . . . . . . . . 605 982 . . . . CAP, radiator pressure 7 lb . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 39 . . . . . . . . . . . . . . . . . . 006 015 . . . . FITTING, pipe brs drain cock 1/4NPT . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 40 . . . . . . . . . . . . . . . . . . 197 826 . . . GUARD, fan upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 41 . . . . . . . . . . . . . . . . . . 109 792 . . . ENCLOSURE, radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 42 . . . . . . . . . . . . . . . . . . 147 923 . . . LABEL, warning fan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 43 . . . . . . . . . . . . . . . . . +197 908 . . . GUARD, fan RH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 44 . . . . . . . . . . . . . . . . . . 010 862 . . . CLAMP, hose 1.312 – 2.250clp dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
. . . 45 . . . . . . . . . . . . . . . . . . 113 676 . . . HOSE, radiator lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 46 . . . . . . . . . . . . . . . . . . 084 979 . . . HOSE, radiator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 47 . . . . . . . . . . . . . . . . . +197 825 . . . GUARD, fan LH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 48 . . . . . . . . . . . . . . . . . . 176 364 . . . ENGINE, gas elec start (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 49 . . . . . . . . . . . . . . . . . . 089 515 . . . . ANGLE, mtg engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 50 . . . . . . . . . . . . . . . . . . 115 857 . . . . BRACKET, mtg solenoid idle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 51 . . . . . TS1 . . . . . . . . 005 373 . . . . SOLENOID, 14VDC .84A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 52 . . . . . . . . . . . . . . . . . . 010 837 . . . . PIN, spring CS .093 x .625 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OM-477 Page 48
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-1. Main Assembly (Continued)
. . . 53 . . . . . . . . . . . . . . . . . . 113 658 . . . . LINKAGE, throttle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 54 . . . . . FS1 . . . . . . . . . . . . . . . . . . . . CARBURETOR, (see engine parts list) . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 55 . . . . . . . . . . . . . . . . . . 602 887 . . . . FITTING, pipe brs plug hexhd 1/4NPT . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 56 . . . . . . S7 . . . . . . . . 025 473 . . . . SWITCH, pressure oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 57 . . . . . . . . . . . . . . . . . . 010 289 . . . . FITTING, brs flrd invt conn M 1/4tbg x 1/8NPT . . . . . . . . . . . . . . . . 1
. . . 58 . . . . . . . . . . . . . . . . . . 111 851 . . . . LINE, fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 087 318 . . . . CLAMP, stl cush 1.000dia x .203mtg hole . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 172 725 . . . . BOOT, starter eyelet terminal red . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 59 . . . . . . . . . . . . . . . . . . Fig 10-2 . . . GENERATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 60 . . . . Shunt . . . . . ♦030 084 . . . SHUNT, meter 50MV 600A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 61 . . . . . . . . . . . . . . . . . . 188 629 . . . HOSE, elbow air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 62 . . . . . . . . . . . . . . . . . . 173 034 . . . TUBING, heat stove . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 63 . . . . . . . . . . . . . . . . . . 010 863 . . . CLAMP, hose 1.125-3.000clp dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 64 . . . . . . . . . . . . . . . . . . 173 036 . . . HOSE, elb air cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 65 . . . . . . . . . . . . . . . . . . 134 779 . . . HOLD DOWN, bat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 66 . . . . . . . . . . . . . . . . . . 182 276 . . . CABLE, battery pos w/clamp (included w/engine) . . . . . . . . . . . . . . . . 1
. . . 67 . . . . . . . . . . . . . . . . . . 047 812 . . . CABLE, battery neg (included w/engine) . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 68 . . . . . . . . . . . . . . . . . . 108 081 . . . TERMINAL PROTECTOR, bat post . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 69 . . . . . BAT . . . . . . . . 071 678 . . . BATTERY, stor 12V 415crk . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 70 . . . . . . . . . . . . . . . . . . 134 782 . . . BATTERY BOX . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 71 . . . . . . . . . . . . . . . . . . 082 672 . . . BOLT, L stl .312-18 x 6.375 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 604 433 . . . NUT, stl slflkg hex hvy .312-18 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 72 . . . . . . . . . . . . . . . . . . 163 666 . . . BASE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 73 . . . . . . . . . . . . . . . . ♦186 008 . . . INSULATION, terminal strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 74 . . . . . . 3T . . . . . . ♦038 601 . . . BLOCK, term 30A 9P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 75 . . . . . . . . . . . . . . . . ♦155 731 . . . BRACKET, mtg terminal strip . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 76 . . . . . . . . . . . . . . . ♦+134 902 . . . COVER, fuse box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 77 . . . . . . . . . . . . . . . . ♦185 000 . . . LABEL, warning auxiliary power . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 78 . . . . . . . . . . . . . . . . ♦026 947 . . . STAND-OFF, insulated 2.50-20 x 1.000 lg . . . . . . . . . . . . . . . . . . . . . . 1
. . . 79 . . . . . . . . . . . . . . . ♦+134 903 . . . FUSE, box . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 80 . . . . . . . . . . . . . . . . ♦149 541 . . . HOLDER, fuse crtg 60A 250V 3 fuses . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 81 . . . . . F1-3 . . . . ♦*012 625 . . . FUSE, crtg 45A 250V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . 82 . . . . . . . . . . . . . . . . . . 113 932 . . . GUARD, panel rcpt (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 83 . . . . . . . . . . . . . . . . . . 113 730 . . . . LABEL, warning stop engine before etc . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 84 . . . . . SR4 . . . . . . . 035 704 . . . RECTIFIER, integ 40A 800 V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 85 . . . . . . . . . . . . . . . . . . 173 982 . . . PANEL, mtg components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 86 . . PLG9,RC9 . . . . . 168 071 . . . CONNECTOR & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 87 . . . . . . D9 . . . . . . . . 192 307 . . . KIT, diode w/washers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 88 . . . . . . C8 . . . . . . . . 170 674 . . . CAPACITOR BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 89 . . . . . . R6 . . . . . . . . 030 844 . . . RESISTOR, WW fxd 25W 25 ohm . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 605 741 . . . CLIP, mtg resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 90 . . . . . CR3 . . . . . . . 044 588 . . . RELAY, encl 12VDC 3PDT 10A/120VAC . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 91 . . . . . PC5 . . . . . ♦150 415 . . . CIRCUIT CARD, connector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . PLG6-8 . . . . ♦141 450 . . . CONNECTOR, rect 10skt plug Amp 207396-1 . . . . . . . . . . . . . . . . . . 3
. . . 92 . . . . . . . . . . . . . . . . ♦097 132 . . . STAND-OFF, No. 6-32 x .375 lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
. . . 93 . . . . . PC6 . . . . . ♦152 966 . . . CIRCUIT CARD, filter HF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 94 . . . . . . . . . . . . . . . . . +181 841 . . . PANEL, front lower . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 95 . . . . . . . . . . . . . . . . ♦134 792 . . . LABEL, warning general precautionary . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 96 . . . . . . . . . . . . . . . . ♦111 785 . . . HANDLE, switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 97 . . . . . . . . . . . . . . . . ♦112 003 . . . SWITCH, plrt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . ♦133 725 . . . LABEL, AC/DC polarity switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 98 . . . . . CT1 . . . . . . . . 105 370 . . . TRANSFORMER, current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 99 . . . . . . Z1 . . . . . . . . 084 814 . . . REACTOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 100 . . . . Neg . . . . . . . . 039 046 . . . TERMINAL, pwr output black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 101 . . . . Pos . . . . . . . 039 047 . . . TERMINAL, pwr output red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 102 . . . . . . . . . . . . . . . . . Fig 10-3 . . . PANEL, front w/components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 103 . . . . . . . . . . . . . . . . . 108 127 . . . BRACKET, mtg term pwr output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 104 . . . . PC4 . . . . . . . 148 608 . . . CIRCUIT CARD, filter HF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 097 132 . . . STAND-OFF, No. 6-32 x .375 lg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . 105 . . . . . . . . . . . . . . . . . 188 237 . . . UPRIGHT, base front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
OM-477 Page 49
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-1. Main Assembly (Continued)
. . 106 . . . . . . . . . . . . . . . . . 085 551 . . . FRAME, mtg reactor/fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 107 . . . . . R3 . . . . . . . . 128 862 . . . RESISTOR, WW adj 375W 50 ohm w/mtg bkt . . . . . . . . . . . . . . . . . . 1
. . 108 . . . . . . . . . . . . . . . . . 085 656 . . . STRIP, mtg resistor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 109 . . . . . . . . . . . . . . . . . 605 288 . . . FITTING, pipe galv plug sqhd .250NPT . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 110 . . . . . . . . . . . . . . . . . 070 010 . . . BOLT, J stl .250-20 x 2.312 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . 111 . . . . . . . . . . . . . . . . . 010 143 . . . CLAMP, nyl .375 clamp dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 112 . . . . . . . . . . . . . . . . . 138 027 . . . EDGE TRIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . 113 . . . . . . . . . . . . . . . . . 081 499 . . . BRACKET, mtg strip terminal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 114 . . . . TE4 . . . . . . . . 038 621 . . . BLOCK, term 30A 4P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 038 620 . . . LINK, jumper term blk 30A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . 115 . . . . . . . . . . . . . . . . . 053 967 . . . INSULATION, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 116 . . . . . . . . . . . . . . . . . 089 517 . . . STRAP, fuel tank . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 010 021 . . . CLAMP, stl cush .562dia . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 136 310 . . . KIT, label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
♦OPTIONAL
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
.
H
a
r
d
w
a
r
e
i
s
c
o
m
m
o
n
a
n
d
19
not available unless listed.
16
18
17
14
15
13
12
7
9
10
11
8
3
12
4
6
5
4
20
2
1
22
21
23
25
26
27
28
24
Figure 10-2. Generator
OM-477 Page 50
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-2. Generator (Fig 10-1 Item 59)
. . . 1 . . . . . . . . . . . . 106 426 . . INSULATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
. . . 2 . . . . . . . . . . . . 106 440 . . BUS BAR, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 3 . . . SR3 . . . . 106 427 . . DIODE ASSEMBLY, reverse polarity (consisting of) . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . . . . . . . 048 420 . . . . CAPACITOR, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . 106 641 . . . . CAPACITOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . . . . . . . 037 957 . . . . DIODE, rect 275A 300V RP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . 6 . . . . . . . . . . . . 106 425 . . . . INSULATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 7 . . . . . . . . . . . . 173 066 . . BRACKET, mtg brushholder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . 018 614 . . BRUSH SET, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . 9 . . . . . . . . . . . . *151 299 . . . . BRUSH, contact . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 10 . . . . . . . . . . . . 600 270 . . . . HOLDER, brush . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 11 . . . . . . . . . . . . 152 044 . . . . CAP, brushholder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 12 . . . . . . . . . . . . 013 367 . . LABEL, warning moving parts can cause serious injury . . . . . . . . . . . . . . . . 2
. . 13 . . . . . . . . . . . . . 110 371 . . GUARD, starter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 14 . . . . . . . . . . . +128 730 . . STATOR, gen (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 14 . . . . . . . . . . +♦132 222 . . STATOR, gen (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 15 . . . . . . . . . . . . 039 207 . . . . BAFFLE, air gen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 16 . . . . . . . . . . . . 201 198 . . ROTOR, gen (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 17 . . . . . . . . . . . . 024 617 . . . . RING, retaining external . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 18 . . . . . . . . . . . . 053 390 . . . . BEARING, ball . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 19 . . . . . . . . . . . . 089 737 . . . . FAN, rotor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . 035 776 . . . . KEY, .375 x .375 x 2.000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 20 . . . . . . . . . . . . 044 374 . . STATOR, excitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 21 . . . . . . . . . . . . 173 068 . . ENDBELL, gen (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 22 . . . . . . . . . . . . 143 220 . . . . O-RING, 2.859 ID x .139CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 23 . . . . . . . . . . . . 106 424 . . BARREL, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . 163 271 . . EDGE TRIM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 24 . . . SR3 . . . . 106 430 . . DIODE ASSEMBLY, straight polarity (consisting of) . . . . . . . . . . . . . . . . . . . 1
. . 25 . . . . . . . . . . . . 048 420 . . . . CAPACITOR, rectifier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . 106 641 . . . . CAPACITOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . 26 . . . . . . . . . . . . 106 425 . . . . INSULATOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . 27 . . . . . . . . . . . . 037 956 . . . . DIODE, rect 275A 300V SP . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . 28 . VR1,R4 . . 046 819 . . . . SUPPRESSOR . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
♦OPTIONAL
*Recommended Spare Parts.
+When ordering a component originally displaying a precautionary label, the label should also be ordered.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-477 Page 51
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-3. Panel, Front w/Components (Fig 10-1 Item 102)
. . . 1 . . . . . . . . . . . . . . . . . . 010 647 . . . PIN, spring CS .156 x 1.250 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . . . . . . . . . . . . . 044 328 . . . HANDLE, switch range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PLATE, ident control rating (order by model and serial number) . . . 1
. . . 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . NAMEPLATE, (order by model and serial number) . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . S1 . . . . . . . . 172 070 . . . SWITCH, ign 5posn w/out handle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ♦ . . . LO OIL & HI TEMP SHUTDOWN, (consisting of) . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 110 958 . . . . SWITCH, automatic shutdown (consisting of) . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . . MS1 . . . . . . . 011 072 . . . . . . SWITCH, magnetic (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 7 . . . . . . F . . . . . . . . *048 317 . . . . . . . . FUSE, mintr gl 14A 32V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . D8 . . . . . . . . 087 970 . . . . . . DIODE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 8 . . . . . . . . . . . . . . . . . . 131 999 . . . PANEL, front upper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 9 . . . . . . . . . . . . . . . . . . 086 706 . . . SPACER, range switch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 10 . . . . . . S3 . . . . . . . . 119 850 . . . SWITCH, range/changeover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 11 . . . . . . . . . . . . . . . . . . 086 991 . . . BRACKET, support switch range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Fig 10-4
.
H
a
r
d
w
a
r
e
i
s
c
o
m
m
o
n
a
n
d
11
12
not available unless listed.
6
8
9
10
7
5
4
3
2
13
1
14
13
15
16
38
37
17
18
39
25
36
26
35
34
33
24
19
Includes
Item 20
32
31
30
29
23
22
28
8
27
3
20
21
ST-115 005-C
Figure 10-3. Panel, Front w/Components
OM-477 Page 52
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-3. Panel, Front w/Components (Fig 10-1 Item 102)
(Continued)
. . . 12 . . . . . . . . . . . . . . . . . . Fig 10-4 . . . CONTROL BOX w/COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 13 . . . . CB1,2 . . . . . . . 139 266 . . . CIRCUIT BREAKER, man reset 1P 15A 250VAC . . . . . . . . . . . . . . . . 2
. . . 14 . . . . RC1,2 . . . . . . . 170 901 . . . RECEPTACLE, str dx grd 2P3W 15A 125V . . . . . . . . . . . . . . . . . . . . . 2
. . . 14 . . . GFCI1,2 . . . . ♦168 068 . . . RECEPTACLE, str dx grd 2P3W 15A 125V . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 073 690 . . . PLUG, str grd armd 2P3W 15A 125V P & S 5266DF
. . . . . . . . . . . . . . . . . . . . . . ♦042 655 . . . RECEPTACLE KIT, 240V (consisting of) . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 13 . . . . CB1,2 . . . . . . . 139 266 . . . . CIRCUIT BREAKER, man reset 1P 15A 250VAC . . . . . . . . . . . . . . 2
. . . 14 . . . . . RC1 . . . . . . . 604 103 . . . . RECEPTACLE, str dx grd 2P3W 15A 250V . . . . . . . . . . . . . . . . . . . 1
. . . 14 . . . . . RC2 . . . . . . . 039 864 . . . . RECEPTACLE, str dx grd 2P3W 15A 125V . . . . . . . . . . . . . . . . . . . 1
. . . 15 . . . . . RC3 . . . . . ♦143 976 . . . CONNECTOR w/SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 134 734 . . . CONNECTOR, circ 14 pin plug Amp 213571-2
. . . . . . . . . . . . . . . . . . . . . . . . 134 731 . . . CONNECTOR, circ pin push-in 14-18ga Amp 213603-1
. . . . . . . . . . . . . . . . . . . . . . . . 079 739 . . . CONNECTOR, circ clamp str rlf .703 max cable OD
Amp 206322-2 (or)
. . . . . . . . . . . . . . . . . . . . . . . . 143 922 . . . CONNECTOR, circ clamp str rlf .453 max cable OD
Amp 206070-3
. . . 16 . . . . CB3,4 . . . . . ♦083 432 . . . CIRCUIT BREAKER, man reset 1P 10A 250V . . . . . . . . . . . . . . . . . . 2
. . . 17 . . . . . S4,5 . . . . . ♦011 609 . . . SWITCH, tgl SPDT 15A 125VAC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 18 . . . . . . . . . . . . . . . . . . 011 611 . . . SWITCH, tgl DPDT 15A 125V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 19 . . . . . . R1 . . . . . . . . 072 462 . . . POTENTIOMETER, w/shaft lock (consisting of) . . . . . . . . . . . . . . . . . 1
. . . 20 . . . . . . . . . . . . . . . . . . 072 590 . . . . LOCK, shaft pot .375-32 x .250dia shaft . . . . . . . . . . . . . . . . . . . . . . 1
. . . 21 . . . . . . . . . . . . . . . . . . 022 289 . . . TUBING, stl .312 OD x .187 ID x .437 . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 22 . . . . . . . . . . . . . . . . . . 097 926 . . . KNOB, pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 23 . . . . . . . . . . . . . . . . ♦021 385 . . . BOOT, tgl switch lever . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 24 . . . . . . . . . . . . . . . . . . 170 663 . . . HINGE, panel front . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 25 . . . . . . . . . . . . . . . . . . 083 030 . . . STUD, brs grd .250-20 x 1.750 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 26 . . . . . . . . . . . . . . . . . . 601 836 . . . NUT, brs hex .250-20 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
. . . 27 . . . . . . A2 . . . . . . ♦046 652 . . . METER, amp dc 50MV 0-600 scale . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 28 . . . . . . V . . . . . . . ♦046 654 . . . METER, volt dc 0-100 scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 29 . . . . . . . . . . . . . . . . ♦170 391 . . . CONNECTOR, circ protective cap Amphenol 9760-20 . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ♦ . . . ENGINE METER KIT, (consisting of) . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 30 . . . . . . . . . . . . . . . . . . 047 842 . . . . GAUGE, pressure 5-100 lbs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 31 . . . . . . . . . . . . . . . . . . 047 841 . . . . GAUGE, temperature mechanical 100/250deg . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 128 829 . . . . KIT, oil line 44.000 in 1/8NPT x 10mm . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 602 946 . . . . FITTING, pipe stl tee B 1/8NPT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 175 465 . . . . FITTING, pipe brs adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 162 380 . . . . FITTING, pipe stl adapter 3/8 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 32 . . . . . . . . . . . . . . . . . . 133 814 . . . CONTROL, push/pull . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 33 . . . . . . . . . . . . . . . . . . 119 014 . . . LEVER, switch black . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 34 . . . . . HM . . . . . . . . 145 247 . . . METER, hour 12-24VDC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . . . . . . . . . . . . . . . 604 784 . . . SCREW, 6-32 x .500rdh-slot brs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . . . . . . . . . . . . . . . . . . . . . . 601 829 . . . NUT, brs hex 6-32 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 35 . . . . . . . . . . . . . . . . . . 082 788 . . . HOLDER, light ind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 36 . . . . . . . . . . . . . . . . . . 082 789 . . . LENS, light ind red . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 37 . . . . PL1,2 . . . . . . *048 155 . . . BULB, incand flg base 12V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
. . . 38 . . . . . . FG . . . . . . . . 118 066 . . . GAUGE, fuel elec 12V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 39 . . . . . . . . . . . . . . . . . . 189 404 . . . SPACER, nylon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
♦OPTIONAL
*Recommended Spare Parts.
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-477 Page 53
Download from Www.Somanuals.com. All Manuals Search And Download.
Item
No.
Dia.
Mkgs.
Part
No.
Description
Quantity
Figure 10-4. Control Box w/Components (Fig 10-3 Item 12)
. . . 1 . . . . . CR1 . . . . . . . 044 588 . . . RELAY, encl 12VDC 3PDT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 2 . . . . . . R2 . . . . . . ♦130 515 . . . RESISTOR, board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 3 . . . . . . D1 . . . . . . . . 189 701 . . . DIODE/CAPACITOR BOARD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 4 . . . . . . 2T . . . . . . . . 116 005 . . . BLOCK, term 10A 7P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 5 . . . . . . 1T . . . . . . . . 129 939 . . . BLOCK, term 10A 19P . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 6 . . . . . . . . . . . . . . . . . . 130 608 . . . MOUNTING BOX, components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 7 . . . . . . . . . . . . . . . . . . 603 107 . . . HOSE, nprn slit back .156 ID x .343 OD (order by ft) . . . . . . . . . . . . . 1ft
. . . 8 . . . . . . . . . . . . . . . . . . 134 201 . . . STAND-OFF SUPPORT, PC card . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
. . . 9 . . . . . PC1 . . . . . ♦166 205 . . . CIRCUIT CARD, field current regulator . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . . . . . . . . PLG1 . . . . . . . 135 275 . . . CONNECTOR PLUG & SOCKETS . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 10 . . . . . PC2 . . . . . . . 114 832 . . . CIRCUIT CARD, voltage regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 11 . . . . CR99 . . . . . . . 090 104 . . . RELAY, encl 12VDC SPST . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 12 . . . . . SR2 . . . . . . . 097 353 . . . DIODE/SCR, bridge integ 2scr 3 diodes . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 13 . . . . . SR1 . . . . . . . 035 704 . . . RECTIFIER, integ 40A 800V . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
. . . 14 . . . Idle Mod . . . . . . 189 742 . . . MODULE, pull to idle 5 pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
1
.
H
a
r
d
w
a
r
e
i
s
c
o
m
m
o
n
a
n
d
not available unless listed.
2
3
4
5
14
13
12
11
PC2
10
PC1
6
7
9
8
ST-109 773-C
Figure 10-4. Control Box w/Components
♦OPTIONAL
To maintain the factory original performance of your equipment, use only Manufacturer’s Suggested
Replacement Parts. Model and serial number required when ordering parts from your local distributor.
OM-477 Page 54
Download from Www.Somanuals.com. All Manuals Search And Download.
Effective January 1, 2000
(Equipment with a serial number preface of “LA” or newer)
This limited warranty supersedes all previous Miller warranties and is exclusive with no other
guarantees or warranties expressed or implied.
Warranty Questions?
LIMITED WARRANTY – Subject to the terms and conditions
below, Miller Electric Mfg. Co., Appleton, Wisconsin, warrants
to its original retail purchaser that new Miller equipment sold
after the effective date of this limited warranty is free of defects
in material and workmanship at the time it is shipped by Miller.
THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE
WARRANTIES OF MERCHANTABILITY AND FITNESS.
*
APT, ZIPCUT & PLAZCUT Model Plasma Cutting
Torches
Call
1-800-4-A-MILLER
for your local
Miller distributor.
*
*
*
*
*
Remote Controls
Accessory Kits
Replacement Parts (No labor)
Spoolmate 185 & Spoolmate 250
Canvas Covers
Within the warranty periods listed below, Miller will repair or
replace any warranted parts or components that fail due to
such defects in material or workmanship. Miller must be
notified in writing within thirty (30) days of such defect or
failure, at which time Miller will provide instructions on the
warranty claim procedures to be followed.
Your distributor also gives
you ...
Miller’s True Blue Limited Warranty shall not apply to:
1. Consumable components; such as contact tips,
cutting nozzles, contactors, brushes, slip rings,
relays or parts that fail due to normal wear.
Service
You always get the fast,
reliable response you
need. Most replacement
parts can be in your
hands in 24 hours.
Miller shall honor warranty claims on warranted equipment
listed below in the event of such a failure within the warranty
time periods. All warranty time periods start on the date that
the equipment was delivered to the original retail purchaser, or
one year after the equipment is sent to a North American
distributor or eighteen months after the equipment is sent to an
International distributor.
2. Items furnished by Miller, but manufactured by others,
such as engines or trade accessories. These items are
covered by the manufacturer’s warranty, if any.
Support
3. Equipment that has been modified by any party other
than Miller, or equipment that has been improperly
installed, improperly operated or misused based upon
industry standards, or equipment which has not had
reasonable and necessary maintenance, or equipment
which has been used for operation outside of the
specifications for the equipment.
Need fast answers to the
tough welding questions?
Contact your distributor.
The expertise of the
distributor and Miller is
there to help you, every
step of the way.
1. 5 Years Parts – 3 Years Labor
*
*
Original main power rectifiers
Inverters (input and output rectifiers only)
MILLER PRODUCTS ARE INTENDED FOR PURCHASE
AND USE BY COMMERCIAL/INDUSTRIAL USERS AND
PERSONS TRAINED AND EXPERIENCED IN THE USE
AND MAINTENANCE OF WELDING EQUIPMENT.
2. 3 Years — Parts and Labor
*
*
*
*
*
*
Transformer/Rectifier Power Sources
Plasma Arc Cutting Power Sources
Semi-Automatic and Automatic Wire Feeders
Inverter Power Supplies
In the event of a warranty claim covered by this warranty, the
exclusive remedies shall be, at Miller’s option: (1) repair; or (2)
replacement; or, where authorized in writing by Miller in
appropriate cases, (3) the reasonable cost of repair or
replacement at an authorized Miller service station; or (4)
payment of or credit for the purchase price (less reasonable
depreciation based upon actual use) upon return of the goods
at customer’s risk and expense. Miller’s option of repair or
replacement will be F.O.B., Factory at Appleton, Wisconsin, or
F.O.B. at a Miller authorized service facility as determined by
Miller. Therefore no compensation or reimbursement for
transportation costs of any kind will be allowed.
Intellitig
Engine Driven Welding Generators
(NOTE: Engines are warranted separately by
the engine manufacturer.)
3. 1 Year — Parts and Labor
*
*
DS-2 Wire Feeder
Motor Driven Guns (w/exception of Spoolmate
185 & Spoolmate 250)
TO THE EXTENT PERMITTED BY LAW, THE REMEDIES
PROVIDED HEREIN ARE THE SOLE AND EXCLUSIVE
REMEDIES. IN NO EVENT SHALL MILLER BE LIABLE FOR
DIRECT, INDIRECT, SPECIAL, INCIDENTAL OR
CONSEQUENTIAL DAMAGES (INCLUDING LOSS OF
PROFIT), WHETHER BASED ON CONTRACT, TORT OR
ANY OTHER LEGAL THEORY.
*
*
*
*
*
*
*
*
*
*
*
*
*
*
Process Controllers
Positioners and Controllers
Automatic Motion Devices
RFCS Foot Controls
Induction Heating Power Sources
Water Coolant Systems
HF Units
ANY EXPRESS WARRANTY NOT PROVIDED HEREIN
AND ANY IMPLIED WARRANTY, GUARANTY OR
REPRESENTATION AS TO PERFORMANCE, AND ANY
REMEDY FOR BREACH OF CONTRACT TORT OR ANY
OTHER LEGAL THEORY WHICH, BUT FOR THIS
Grids
Maxstar 140
PROVISION,
MIGHT
ARISE
BY
IMPLICATION,
Spot Welders
OPERATION OF LAW, CUSTOM OF TRADE OR COURSE
OF DEALING, INCLUDING ANY IMPLIED WARRANTY OF
MERCHANTABILITY OR FITNESS FOR PARTICULAR
PURPOSE, WITH RESPECT TO ANY AND ALL
EQUIPMENT FURNISHED BY MILLER IS EXCLUDED AND
DISCLAIMED BY MILLER.
Load Banks
Miller Cyclomatic Equipment
Running Gear/Trailers
Plasma Cutting Torches (except APT & SAF
Models)
Some states in the U.S.A. do not allow limitations of how long
an implied warranty lasts, or the exclusion of incidental,
indirect, special or consequential damages, so the above
limitation or exclusion may not apply to you. This warranty
provides specific legal rights, and other rights may be
available, but may vary from state to state.
*
Field Options
(NOTE: Field options are covered under True
Blue for the remaining warranty period of the
product they are installed in, or for a minimum of
one year — whichever is greater.)
In Canada, legislation in some provinces provides for certain
additional warranties or remedies other than as stated herein,
and to the extent that they may not be waived, the limitations
and exclusions set out above may not apply. This Limited
Warranty provides specific legal rights, and other rights may
be available, but may vary from province to province.
4. 6 Months — Batteries
5. 90 Days — Parts
*
*
MIG Guns/TIG Torches
Induction Heating Coils and Blankets
miller_warr 7/00
Download from Www.Somanuals.com. All Manuals Search And Download.
Owner’s Record
Please complete and retain with your personal records.
Model Name
Purchase Date
Distributor
Address
Serial/Style Number
(Date which equipment was delivered to original customer.)
City
State
Zip
For Service
to locate a DISTRIBUTOR or SERVICE AGENCY near you.
Always provide Model Name and Serial/Style Number.
Contact your Distributor for:
Welding Supplies and Consumables
Options and Accessories
Personal Safety Equipment
Service and Repair
Miller Electric Mfg. Co.
An Illinois Tool Works Company
1635 West Spencer Street
Appleton, WI 54914 USA
Replacement Parts
Training (Schools, Videos, Books)
International Headquarters–USA
USA Phone: 920-735-4505 Auto-Attended
USA & Canada FAX: 920-735-4134
International FAX: 920-735-4125
Technical Manuals (Servicing Information
and Parts)
Circuit Diagrams
European Headquarters –
United Kingdom
Phone: 44 (0) 1204-593493
FAX: 44 (0) 1204-598066
Welding Process Handbooks
Contact the Delivering Carrier for:
File a claim for loss or damage during
shipment.
For assistance in filing or settling claims,
contact your distributor and/or equipment
manufacturer’s Transportation Department.
PRINTED IN USA
2000 Miller Electric Mfg. Co. 6/00
Download from Www.Somanuals.com. All Manuals Search And Download.
|