MIL-S800 User’s Guide
8 port 10/100BASE-TX Switch
Download from Www.Somanuals.com. All Manuals Search And Download.
Table of Contents
Chapter 1. Introduction
Pg 1
1-1 General Description…………………………………….
Pg. 1
Pg. 1
Pg. 2
Pg. 3
1-2 Key Features………………………………………………
1-3 Package Contents………………………………………
1-4 Hardware Description…………………………………..
Chapter 2. Hardware Installation
Pg 4
2-1 Quick Installation………………………………………...
2-2 LED Descriptions………………………………………….
Pg. 4
Pg. 5
Chapter 3. Network Application
Pg 6
Pg. 6
Pg. 6
3-1 Stand Alone………………………………………………
3-2 Uplink Multiple Hubs…………………………………….
Chapter 4. Trouble Shooting
Pg 7
Chapter 5. Product Specifications
Pg 8
5-1 General Specification…………………………………..
5-2 Performance Specification
5-3 Physical & Environmental Specification……………..….
Pg. 8
Pg. 8
Pg. 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1 Introduction
1-1 General Description
The MIL-S800 switch provides eight auto-sensing 10/100Mbps RJ45 Ethernet ports. This high performance,
low cost, wire speed desktop switch is ideal for any network where 8 ports are needed, for a solution to an
enterprise need or for a home network. The MIL-S800 can be mounted on the wall with keyholes in the
chassis or magnetically attached to any metal surface.
1-2 Key Features
• Compliant with IEEE 802.3, 802.3u & 802.3x standards
• 8 Auto-sensing RJ-45 ports for 10BASE-T or 100 BASE-TX connections
• Embedded 2K entry MAC address table
• 512KB memory buffer sharing
• Store-and-Forward operation support
• Full duplex and half duplex flow control
• Plug-and-Play configuration auto addresses learning
• LED indicators for power, link speed 100Mbps, link and activity, full duplex and collision
• Space-saving compact size
• Wall or desktop mountable
• Magnets provide installation on any metal surface
• Auto MDI/MDIX
1
Download from Www.Somanuals.com. All Manuals Search And Download.
1-3 Package Contents
Your package contents should include the following parts:
• One 8-port Auto-sensing switching Hub
• One DC power adapter
• This User’s Guide
• Four rubber feet with adhesive pads
• Two magnets
• Warranty card
Figure 1. Package contents
2
Download from Www.Somanuals.com. All Manuals Search And Download.
1-4 Hardware Description
The Front Panel
The front panel contains power and LED Indicators.
Figure 2. Front panel view of the MIL-S800
Front panel LED Indicators
Per Device
Power
100M (Link on 100Mbps)
LNK/ACT (Link/Activity)
FDX/COL (Full Duplex/Collision)
Per Port
For LED details, please refer to Chapter 2, LED Descriptions.
The Rear Panel
The rear panel of the MIL-S800 consists of a DC power connector and 8 auto-sensing ports.
Figure 3. Rear panel view of the MIL-S800
· Eight Auto-sensing RJ-45 ports for 10BASE-T or 100 BASE-TX connections.
· Auto MDI/MDIX: Detects the straight cable connection, NIC or cascade to a hub or switch, without
changing the cable.
· DC Power Connector.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2 Hardware Installation
2-1 Quick Installation
• The MIL-S800 should be placed in a well-ventilated room with proper temperature and humidity.
• Do not place the unit near water.
• The maximum distance between the port to the standard network interface is 100 meters.
• For desktop installation, ensure the surface is clean, smooth, level and sturdy. Apply self-adhesive rubber
feet to the bottom of the switch near the corners.
• For wall installation, place two screws securely into the wall. Slide the cross recesses on the bottom of the
MIL-S800 onto the screws.
• For mounting the MIL-S800 on a metal surface, install magnets as shown in instructions and apply to
surface.
• Visually check that the power cord is not damaged. Plug the female end of the cord into the rear of the
MIL-S800 and the male end (power converter) into a power outlet.
• Do not plug a phone jack connector into any RJ-45 port. This may cause damage. Use only twisted-pair
cables with RJ-45 connectors that conform to FCC standards.
Figure 4. Installation of switch
4
Download from Www.Somanuals.com. All Manuals Search And Download.
2-2 LED Descriptions
Figure 5. Front panel view of LED indicators
The following table lists the LEDs and their function.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3 Network Application
3-1 Stand Alone
The application of a simple standalone switch is illustrated below. The maximum distance between the switch
and the workstation is 100 meters.
Figure 6. The switch as a backbone for a small 10/100BASE-TX network
3-2 Network
You can cascade the MIL-S800 to another hub or a switch without using a crossover cable.
Figure 7. Small Network Configuration
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4 Troubleshooting
• Power
If the power indicator is not on after the power cord is plugged in, check the power outlet or power cord. If
you lose power after the switch has been operating for some time, check for loose power connections,
power losses or surges at the power outlet. Disconnect and reconnect the power. If the problem persists,
contact MiLAN Technical Support.
• Cabling
Verify that the cabling type is correct. Be sure all cable connectors are securely seated in the required
ports. Use standard unshielded twisted-pair (UTP), Category 3, 4, or 5 cables. Use only Category 5
when there is a Fast Ethernet connection. Make sure the distance between the MIL-S800 and the
workstation, is less than 100 meters.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 5 Product Specification
5-1 General Specification
IEEE 802.3 10Base-T Ethernet
Standard Compliance
IEEE 802.3u 100Base-TX Fast Ethernet
8 10/100Mbps Auto-sensing RJ-45 ports
Number of Ports
Ethernet :10Mbps(half duplex)
20Mbps(full duplex)
Fast Ethernet : 100Mbps(half duplex)
Data Transfer Rate
200Mbps(full duplex)
Network Cables
LED Indicators
Per Device
Unshielded twisted-pair cable
Power
Per Port
LNK/ACT, 100M, FDX/COL
5-2 Performance Specification
Transmission Method Store and forward
MAC address table
2 K entry MAC address table
Maximum Forwarding 14,880 pps /10 BASE-T
Rate(64byte packets) 148,800 pps /100BASE-TX
Maximum Filtering
14,880 pps /10BASE-T
Rate(64byte packets) 148,800 pps/100BASE-TX
Duplex mode
Supports both half and full duplex mode
5-3 Physical & Environmental Specification
Power Supply
Dimensions
External power adapter,
DC 9V, 700mA
4.2 Watt power consumption
6.5" (165mm) L x 4.0" (100mm) W x 1.0"
(25mm) H
Operating temperature:
0C to 45C (32F to113F)
Storage temperature:
Temperature
-30C to 60C (-22F to 140F)
10% to 90% (non-condensing)
FCC Class B, CE mark
Humidity
EMI
8
Download from Www.Somanuals.com. All Manuals Search And Download.
90000377_F
9
Download from Www.Somanuals.com. All Manuals Search And Download.
|