Operating manual
Washer
PW 6065 Plus
To prevent accidents
and machine damage
read these instructions
before
V
installation or use.
M.-Nr. 06 523 700
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Installation on a base. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Leveling the washer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Water connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Technical Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Help to protect the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Settings J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
Language J . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Time of day . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Temperature unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Menu Settings - Supervisor level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Technical Safety
Read the operating instructions
before using this machine for the
first time. They contain important
information about the safety, use and
maintenance of the machine. Doing
so will prevent injury and damage to
the dryer.
Check the packaging, the washer
and accessories for any signs of
damage. Do not use a damaged
appliance.
Before connecting the machine,
ensure that the connection data on
the data plate (fusing, voltage and
frequency) match the mains electrical
supply. If in doubt contact an
electrician.
Save these instructions and pass
them on to any future user.
WARNING - To reduce the risk
of fire, electric shock or injury:
The appliance must be grounded.
It is imperative that this basic
safety requirement be met.
Use
Do not connect the appliance to
the mains electrical supply with an
extension cord. Extension cords do not
guarantee the required safety of the
appliance (e.g. danger of overheating).
Only use the washing machine to
wash items which are specified by
the manufacturer to be machine
washable on the fabric care label. Any
other applications may be dangerous.
The manufacturer cannot be held
responsible for damage caused by
improper use of the appliance.
The machine is built in accordance
with current safety requirements.
Incorrectly repaired machines may
pose a considerable risk to the user
which is not covered by the
manufacturer. Repairs should only be
performed by a Miele approved
technician.
Ensure power is not supplied to the
appliance while maintenance or
repair work is being performed. The
machine is only completely isolated
from the electrical supply when it is
turned off at the main switch and the
plug is pulled or by tripping the circuit
breaker.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Connect the washer, to the water
Before using the machine for the
first time, check that the shipping
struts at the rear of the machine have
been removed (see "Installation").
During spinning, if the shipping struts
are still in place damage may result to
both the machine and adjacent
furniture or appliances.
mains. Do not use old hoses.
Check the intake hoses regularly for
damage. They should be replaced
regularly to prevent water damage.
Faulty components must only be
replaced with genuine Miele spare
parts. Only when these parts are fitted
can the safety standards of the
machine be guaranteed.
Turn off the water supply if the
machine is to be left for any length
of time (e.g. vacation), especially if
there is no floor drain (gully) in the
immediate area.
If the power cord is damaged it
must only be replaced by a Miele
Service technician with a genuine Miele
power cord.
Overflow hazard!
Check that the drain can
accommodate the water flow before
operating the washer.
Make certain the drain hose is secured
in the drain. Otherwise the force of the
expelled water could cause the drain
hose to come out of the drain.
Use
This appliance is not designed for
maritime use or for use in mobile
installations such as recreational
vehicles or aircraft. However, under
certain conditions it may be possible for
installation in these applications. Please
contact the Miele Technical Service
Department with specific requirements.
Be sure that foreign objects (e.g.
nails, pins, coins, paper clips) do
not find their way into the machine.
These items may damage the
machine, which may also cause
damage to the laundry.
Do not install this machine in rooms
where temperatures below freezing
may occur. Frozen hoses may burst
under pressure. The reliability of the
electronic control unit may be impaired
at temperatures below freezing.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
If the correct amount of detergent
is dispensed, the machine should
not need to be descaled. If the washer
needs to be descaled, use a descaling
agent with corrosion protection. These
special descaling agents can be
purchased from the Miele Service
department. Use as directed.
The stainless steel casing must not
come in contact with liquid
cleaning or disinfection agents
containing chlorine. They may cause
corrosion. Do not store open
containers of this agent next to the
machine.
Children
Never use solvent based cleaning
agents in this machine, this may
result in damage and create toxic
fumes. Fire and explosion hazard.
Close supervision is necessary
when the appliance is used near
children. Do not allow children to play
on or in the appliance.
Items which have been pre-treated
in solvent based cleaning agents
must be thoroughly rinsed in clean
water before being washed in the
machine.
Using accessories
Accessories must only be installed
once approved by Miele. Installing
unapproved parts may void the
warranty and product liability.
Only use dyes specified by the
manufacturer as being suitable for
use in a washing machine. Use as
directed by the manufacturer.
Dye removers may contain sulphur
compounds which cause damage
such as corrosion. Do not use dye
removers in this machine.
The drum door glass will be hot
when washing at very high
temperatures. Do not touch the glass.
Danger of burns!
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the washer
Control panel
a Display
See the following pages for more information
b Direct select buttons
To select a wash program directly. You can also save a "Favorite" wash program
on these buttons.
c "Start" button
d Optical interface PC
Allows a service technician to check and update the wash programs
e Jog shuttle
Turn to select menus
Press to confirm the selection
f a Door button to open the drum door.
Description of the machine
The washer is suitable for use in laundromats or community laundromats for large
amounts of laundry.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the washer
Display function
Main menu
1
Cottons Uni.
60°C
40°C
40°C
30°C
Program selection
2
3
4
Wrinkle-free
Delicates
Settings
F
Woollens H
12:00
The display shows the main menu (with factory default
settings). "Program selection" is highlighted.
If the display is dark (in Stand-by mode) turn the jog shuttle.
Jog shuttle
Turn the jog shuttle to select a program or setting.
Press the jog shuttle to confirm the selection.
Direct select buttons
The first four programs shown in the display on the left are the
"Favorites". They can be selected with the direct select
buttons.
The Favorites can be individually set to your desire. See
"Favorites" for more information.
The direct select buttons have different functions in the other
menus. In these menus an arrow H is displayed above the
respective button with the function description of the button.
Program selection possibility
– Possibility 1 Select and confirm the menu "Program
selection" in the display with the jog shuttle.
– Possibility 2 Press one of the direct select buttons
D E F G and access directly the basic menu of
the program.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the washer
Menu Program selection
Program
selection
backA
Cottons Hygiene
Cottons Uni.
Wrinkle-free
H
All pre-set programs can be selected with the jog shuttle.
Depending on the direction the jog shuttle is turned the
highlighter moves up or down. The arrows e- at the right
side of the display show that more selections are available.
Press the jog shuttle to open the basic menu of the selected
wash program.
Basic menu of a wash program
Cottons
60°C
1400 rpm
Duration 0:45 h
Extras
Delay Start Y
Back A
H
H
H
The program components (program, temperature and spin
speed) can be selected by turning the jog shuttle. The
selected component is highlighted. Press the jog shuttle to
select the component. The respective submenu is displayed.
The submenu "Extras" and "Delay Start" can be selected by
the direct select buttons.
To go back to the main menu, press G "back".
All components can also be selected and confirmed with the
jog shuttle only.
Settings J
The "Settings" menu allows you to adjust the washer to
individual needs. See "Settings" for more information.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Shipping struts
The appliance must be correctly
installed and connected before the
first use. Please see the "Installation
instructions."
The display reminds the user to remove
the shipping struts.
^ If the shipping struts were already
removed, confirm with the G
button. Otherwise remove them at
this time then confirm.
For safety reasons, it is not possible to
run a spin cycle before the first use. A
program must be run without laundry
and detergent to flush out any residual
water from the factory testing process.
Set the time of day
^ Set the hour by turning the jog shuttle
and press to confirm.
^ Open the water mains.
^ Repeat to set the minutes and
confirm. Press again to save the time
of day.
Welcome screen
The Welcome screen shows when the
washer is turned on for the first time.
Basic menu "Cottons Uni." shows
^ Press the flashing button "Start".
The drum door must be closed.
M
PROFESSIONAL
Welcome!
Once the program ends the washer can
be used for laundry.
The welcome screen will not show
anymore, when the total wash time of
the washer exceeds one hour.
The display then shows the language
selection.
Language J
^ Select the desired language and
confirm with "OK".
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the washer
1. Sort the laundry
General tips
– Dark fabrics often bleed the first few
times they are washed. They should
be washed separately several times
before being included in a mixed
load.
– Remove any lead weights or strips
from curtains before washing.
– Loose underwires should be
removed or sewn in place before
washing.
– Woolens and knitted garments
should be turned inside out.
– Close zippers and hooks and eyes
before washing.
^ Empty all pockets.
,Foreign objects left in pockets
(e.g. nails, coins, paper clips, etc.)
can cause damage to clothes and
the machine.
– Comforter covers and pillowcases
should be fastened in order to
prevent small items from rolling
inside of them.
Do not machine wash items if it is not
^ Pre-treat stains.
recommended on the fabric care label.
Tough stains (blood, egg, coffee, tea
etc.) or badly soiled areas (collars and
cuffs) should be penetrated with a stain
remover or a paste made from powder
detergent and warm water. Dab stains
with a damp light colored cloth. Do not
rub!
,Do not use chemical solvents in
the machine.
^ Sort the laundry.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the washer
2. Load the washer
3. Select a program
^ Open the drum door using the a
Two program selection possibilities:
button.
– Select a "Favorite" by pressing the
respective direct select button.
The drum light lights.
^ Load the laundry loosely into the
drum.
– Select from the "Program selection"
menu by turning the jog shuttle.
For best results, wash mixed loads of
small and large items. This will improve
washing effectiveness and help
distribute the load evenly.
^ If desired select "Extras" and/or a
delay start time with the respective
submenus.
Coin mechanism
For the lowest energy and water
consumption load the washer to its
max. capacity. See "Program guide".
If a coin mechanism operates the
machine, please regard the displayed
Note: Overloading the washer will affect request to pay.
wash results and cause wrinkling.
If the door is opened after a program
has started or if the program is
canceled the credit is lost.
^ Close the drum door.
Close the drum door. To prevent
damage to the door seal and
clothing, make sure that there are no
clothes caught between the drum
door and the seal.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the washer
4. Adding detergent
Use detergent according to the laundry
soiling and water hardness.
Too little detergent may cause:
– ineffective cleaning of laundry;
fabrics may become gray and stiff
over time.
– grease stains on the laundry.
– hard water deposits on the heating
element.
Too much detergent may cause:
^ Pull out the detergent dispenser
drawer and add detergent.
– oversudsing with minimal drum
movement; poor wash, rinse and
spin results.
j = Detergent for the main wash
i = Only add detergent (1/4 of the
total recommended amount of
detergent) to this compartment
for the pre-wash.
– higher environmental burden.
See "Detergent" for more information.
§
= Fabric softener or liquid starch.
^ Close the detergent dispenser
drawer.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the washer
5. Starting a program
6. At the end of a program
"Start" flashes when a program can be
started.
The anti-crease program starts when
the laundry is not immediately removed
from the washer after the program end.
"Anti-crease" and "End" will flash
alternately in the display.
^ Press the "Start" button.
The "Start" button lights.
The display shows the approximate
program run time. It will count down in
minutes. The first 10 minutes the
washer calculates the water
^ Use the a "Door" button to open the
drum door.
^ Remove the laundry.
absorbency of the laundry. The overall
program time may be shortened or
lengthened.
Check the drum for any missed
pieces of laundry. Items
inadvertently left in the washer may
be damaged (e.g. shrink or discolor)
during the next wash cycle.
Additionally the sequence cycle is
displayed. The washer shows the
current program step.
The drum light turns off after the
program starts.
Press one of the following direct select
buttons during the running program:
– Button D "Extras"
the displayed Extras can be selected
or deselected after the program start.
– Button E "Delay Start"
the time of day and the approximate
program end is displayed.
– Button G "Cancellation"
to cancel the currently running
program. The wash water will be
drained away.
^ Check the folds of the door seal for
any small articles which may have
been trapped.
^ Close the drum door. Otherwise
foreign objects may find their way
into the drum. These could be
inadvertently washed and cause
damage to laundry.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Favorites
The washer has the option to save the most used wash
programs on the direct select buttons. The option "Save"
must be selected in the "Settings - Supervisor level".
Contact Technical Service for access to this level.
Selecting/Changing a Favorite
Main menu
1
Cottons Uni.
Minimum iron
Delicates
60°C
40°C
40°C
30°C
Program selection
2
3
4
Settings
F
Woollens H
12:00
^ Press any direct select button, e.g. D.
Basic menu
Cottons Uni.
60°C
1400 rpm
Duration 0:45 h
Extras
Delay Start
Save
H
Back A
H
Y
H
H
^ Turn the jog shuttle to select the component you want to
adjust: program, temperature or spin speed.
^ Press the jog shuttle to confirm the selection.
Depending on the selection the display shows one of the following
submenus.
Important: If no selection is made in the sub-menu, the
display will switch back to the basic menu after 20
seconds.
– Select a program
Program
selection
BackA
Cottons Hygiene
Cottons Uni.
Minimum iron
H
^ Select the desired program with the jog shuttle and
confirm. The basic menu shows again.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Favorites
– Selecting a temperature
Cottons Uni.
60 °C
1400 rpm
Temperature
cold - 60°C
a
^ Select the desired temperature with the jog shuttle and
confirm. The basic menu shows again.
– Selecting the spin speed
Cottons Uni.
60 °C
1400 rpm
Spin speed
0 - 1400 rpm
t
^ Select the desired spin speed with the jog shuttle and
confirm. The basic menu shows again.
Selecting Extras
^ Press the direct select button D. The sub-menu "Extras"
shows.
Cottons Uni.
60°C
1400 rpm
Rinse hold
Options
Pre-wash
BackA
Starch Stop
^ Select the desired Extras with the jog shuttle and confirm.
The basic menu shows again. Repeat if another Extra is
desired. See "Extras" for more information.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Favorites
Saving a Favorite
The basic menu shows all selected components.
Cottons Uni.
40°C
1400 rpm
Pre-wash
Duration 00:53:00 h
Extras
Delay Start Y
Save
H
Back A
H
H
H
^ Press the direct select button F.
Assigning a direct select button
Cottons Uni.
40°C
1400 rpm
Pre-wash
until now
Saving to
:
:
Cottons Uni.
60°C
1400 rpm
1
2
3
4
BackA
^ Select the desired number for the favorite with the jog
shuttle and confirm. The favorite is saved with the individual
selections and shows in the main menu.
To assign more favorites, repeat the process with the
remaining direct select buttons.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
The basic wash programs can be enhanced with "Extras".
Accessing the sub-menu "Extras"
Cottons Uni.
60°C
1400 rpm
Duration 0:45 h
Extras
Delay Start Y
Back A
H
H
H
^ Press the direct select button D. The sub-menu "Extras"
shows.
Selecting Extras
Cottons Uni.
60°C
1400 rpm
Rinse hold
Options
Pre-wash
BackA
Starch Stop
^ Select the desired Extras with the jog shuttle and confirm.
– Repeat if another Extra is desired.
– A selected Extra is marked with a tick.
Pre-wash
For laundry with heavy soiling e.g. dust, sand.
Starch Stop
The water is drained away in the last rinse and the program
stops.
Fill the starch directly into the drum and then continue the
program. See "Detergent - Separate starch" for more
information.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Options
Rinse Stop
The washer stops after the last rinse, the laundry remains
soaking in water. This will prevent wrinkles if the laundry is not
removed immediately at the end of the wash program.
Intensive*
For laundry with normal to heavy soiling or stains.
The total time for the wash program will be extended.
Water plus*
The washer comes factory set with the Extra selection "Water
plus" activated. The water level during washing and rinsing is
increased.
Other settings for "Water plus" can be selected. See "Settings"
for more information.
* "Intensive" and "Water plus" can be added from the "Settings
- Supervisor level" menu, when the access is activated by
Technical Service.
Extras which can be selected are shown in the sub-menu
"Extras". If an Extra is not shown, it is not available for the
selected program.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Delay Start
The delay start option allows you to select the program end
time. The program start can be delayed between 30 minutes
and 24 hours.
Select the sub-menu Delay Start
Cottons Uni.
60°C
1400 rpm
Duration 0:45 h
Extras
Delay Start Y
Back A
H
H
H
^ Press the direct select button E. The "Delay Start" menu
shows.
Select the Delay Start time
The program end can be selected in 30 minute steps.
Cottons Uni.
60°C
1400 rpm
Start time:
Finish:
15:45
16:30
12:03
^ Select the desired program end time with the jog shuttle
and confirm. The program end time is adjusted to the next
full or half hour. The program start will be delayed
according to the desired program end time.
Starting the Delay Start
^ Press the "Start" button.
The elapsed delay start time is displayed and will count down
in minutes.
Canceling the Delay Start
^ The Delay Start can be canceled with the direct select
button G.
After the program start the actual load size is measured.
This can result in an earlier program end.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Spin
Spin speed
Rinse spin
Program
rpm
1400
1400
1000
600
The laundry is spun after the main wash
and between the rinse cycles.
Reducing the final spin speed will also
reduce the rinse spin speeds.
Cottons Hygiene
Cottons Uni.
Minimum iron
Delicates
Sturdy
Without final spin
1200
1200
400
^ Select "Rinse Stop" from the
Woollens
Silk
sub-menu "Extras". The laundry is not
spun and remains soaking in water.
This will prevent wrinkles if the
laundry is not removed immediately
at the end of the wash program.
Shirts
600
Denim
900
Disinfection programs*
Kitchen linen*
Table linen*
Curtains*
Pillows*
1400
1400
1200
400
– Selecting the final spin
The washer is set default to the
maximum spin speed of the wash
program. You can select a lower spin
speed. Press "Start" to start the final
spin.
1400
900
Outerwear*
Proofing*
Towelling
Sluice*
800
1400
1400
1400
– To finish the program
Spin
Press the a button. The water will
be drained. Press the a door
button to open the door.
* = Programs can be added from the "Settings -
Supervisors level" when activated by the
Technical Service.
The final spin speed can be reduced.
The speeds above are the highest
available.
Deselect rinse spin and final spin
^ Select "Without spin". The laundry is
not spun after the final rinse but the
water is drained away. After the drain
cycle the washer goes immediately
into the anti-crease cycle.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Program guide
Cottons Hygiene 95°C to 70°C
9Fö
Items
Items made from cottons and linen, i.e. bed linen, baby clothing,
underwear
Detergent
Load size
Universal detergent
6.5 kg
Cottons Uni. 60°C to cold
876
Items made from cottons or mixed fabrics, i.e. T-Shirts, pants
Wash dark colored fabrics with detergent for colors or a liquid
Items
Tip
detergent.
Detergent
Load size
Universal or color detergent
6.5 kg
Minimum iron 60°C to 30°C
421
Items
Items made from synthetics, mixed fabrics or wrinkle free cottons,
i.e. shirts
Detergent
Load size
Universal or color detergent
3.5 kg
Delicates 60°C to 30°C
ac
Items
Delicates made from synthetics, mixed fabrics or viscose silk
Detergent
Load size
Detergent for delicates
2.5 kg
Quick wash 40°C to cold
76
Items
Small load of lightly soiled items, which can be washed in
"Cottons Uni."
Detergent
Load size
Universal or color detergent
3.5 kg
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Program guide
Woollens 40°C to cold
Items
Items made from machine washable wool and wool blend
fabrics.
Detergent
Load size
Detergent for wool
2.5 kg
Silk / 30°C to cold
Items
Hand washable items, that contain no wool.
Wash hosiery and lingerie in a lingerie bag.
Tip
Detergent
Load size
Detergent for delicates
2.5 kg
Shirts 60°C to cold
Items
Tip
Shirts and dress shirts.
– Pre-treat collars and cuffs depending on soiling
– Wash silk shirts in the "Silk" program.
Detergent
Load size
Universal or color detergent
2.5 kg
Denim 104°C to cold
Tip
– Before washing denim items turn them inside out.
– Denim items bleed at the first few washes. Wash dark and
light colored items separately.
Detergent
Load size
Liquid color detergent
3.5 kg
Towelling 95°C to 60°C
Tip
Use color detergent for dark colored laundry
Detergent
Load size
Drain
Universal detergent
5.5 kg
To drain the water from the drum
Spin
Please select an appropriate spin speed
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Program guide
Additional programs
The following programs can be added from the "Settings - Supervisor level"
when activated by Technical Service.
Kitchen linen 95°C to 60°C
Items
Kitchen linen made from cottons and linen, i.e. chef jackets and
pants, towels, rags
Tip
Use the "Pre-wash" program for tough stains. Use a pre-wash
detergent with enzymes.
Detergent
Load size
Universal detergent
3.5 kg
Table linen 60°C to 30°C
Items
Table cloths and napkins made of cottons, linen or mixed
fabrics.
Tip
Use the "Pre-wash" program for tough stains. Use a pre-wash
detergent with enzymes.
Detergent
Load size
Universal detergent
6.5 kg
Curtains 104°C to cold
Items
Curtains which are machine washable according to the
manufacturer. To rinse dust, a pre-wash without detergent is
automatically added to the program.
Tip
Curtains that wrinkle easily should be washed at a reduced spin
speed or without a spin .
Detergent
Load size
Curtain, universal and color detergent in powder form.
3.0 kg
Pillows 95°C to 40°C
Items
Washable pillows with a filling of feathers, down or synthetics.
Tip
Regard the fabric care label!
Liquid detergent
Detergent
Load size
1 queen and 2 twin size pillows
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Program guide
Outerwear 40°C to cold
Items
Tip
Outdoor clothing made from micro fibers.
– Close all zippers.
– Do not use fabric softener
Detergent
Load size
Detergent for delicates
3.5 kg
Proofing 104°F to 86°F
Items
To treat micro fiber, ski clothing, fine dense cotton (popelin) or
table cloths to make them water repellent and soil resistant.
Tip
– The item should be washed and rinsed or dried.
– To get an optimum result dry the items in a clothes dryer or iron
them.
Water
repellent
– Only use water repellent with the hint "Suitable for membrane
textiles". They are based on fluorochemicals. Do not use
agents containing paraffin.
– Place the liquid detergent insert in compartment j an fill with
water repellent.
Load size
3.5 kg
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Program guide
Disinfection programs
Items
Note
Bed linen made of cottons or mixed fabrics.
For different requirements with a temperature selection of 85°C
(thermal) to 40°C (chemothermal) with the respective holding
times.
Detergent
Use a detergent for disinfection and chemothermal disinfection.
Regard the temperature level recommended on the packaging.
Load size
6.5 kg
Hygiene
If a temperature lower than 55°C was selected for the last wash program or if the
program "Spin" was selected, "Hygiene" is displayed.
When selecting a Hygiene program
– do not put any laundry into the drum, add a small amount of detergent in
compartment j and start the program,
or
– select a wash program with a temperature of 60°C or higher.
If the "Hygiene" display is disregarded, each program will run accordingly.
Sluice 75°C or Sluice 65°C
Items
Heavily soiled items of cottons, linen or mixed fabrics.
To remove heavy soiling the laundry will be pre-rinsed twice.
Universal detergent
Note
Detergent
Load size
6.5 kg
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Program sequence
Main wash
Rinse
Spin
Water
Wash
rhythm
Water Rinses Rins spin Final spin
level
level
d
d
d
e
d
(
e
(
(
(
(
(
(
(
(
–
Cottons Hygiene
Cottons Uni.
Minimum iron
Delicates
a
a
a
b
a
c
d
a
a
a
a
a
a
a
b
–
(
(
(
e
(
(
e
(
(
(
(
(
(
(
e
(
(
(
–
2
2
2
2
2
2
2
2
3
3
2
2
3
3
3
1
2
3
–
L
L
L
–
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
Sturdy
L
L
–
Woollens
Silk
Dress Shirts
Denim
–
–
Disinfection*
Kitchen linen*
Table linen*
Curtains 2)*
Pillows 1)*
Outerwear*
Proofing*
L
L
L
–
–
L3)
L
L
L
–
Towelling
Sluice4)*
(
(
–
a
a
–
Spin
d = low water level
( = middle water level
e = high water level
a = normal wash rhythm
b = Gentle wash cycle
c = Woolens
d = Silk
For program sequence explanations, see the following page.
* = Programs may be added from the "Settings - Supervisor level" when
activated by Technical Service.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Program sequence
The washer is equipped with a
Special features in the program
electronic control which determines the sequence:
load size automatically. The washer
determines the required water
consumption for each load and
depending on quantity and water
absorbency of the laundry. Different
program sequences and wash times
will result.
Anti-crease
The drum continues to turn up to 30
minutes after the program ends to
prevent creases. The washer can be
opened at any time. Exception: The
program "Woollens" has no anti-crease
feature.
The program sequence shown here
represents the basic program with a
maximum load. Possible "Extras" are
not considered.
1)
High Spin
Before the wash program starts, a
high spin is carried out to remove air
from the pillows. After the spin the
water is taken in by the compartment
j for the main wash.
The washer’s sequence display will
indicate the current cycle of the
selected wash programs.
2)
Pre-rinse
To rinse dust, a pre-wash without
detergent is automatically added to
the program.
3)
Outerwear
The items will be spun only after the
main wash.
4)
Pre-rinse
To remove heavy soiling the laundry
will be pre-rinsed twice.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
To change a program
To cancel a program
Note:
A program can be canceled any time
after a program start.
Once the program has started the
washer cannot make adjustments of the
load size. After adding or removing
laundry, the washer will default to the
water and electrical consumption of a
full load.
^ Press the button G "Cancellation".
The wash water will be drained away.
^ Open the drum door before starting a
new program.
The time remaining will automatically be
adjusted.
To change a program
The drum door cannot be opened if:
After the program start the spin speed
can be selected until the final spin
starts. The Extras "Starch Stop" and
"Rinse Stop" can be selected or
deselected.
– the water temperature is greater than
55°C.
– the water level is too high.
– the program has reached the "Final
Spin".
The temperature and the Extra
"Intensive" can be selected or
deselected up to 5 minutes after the
program start.
When operated with a coin
mechanism the machine will be
locked after 3 minutes. Canceling or
changing a program and opening
the door is no longer possible.
Adding/removing laundry
during a wash program
You can interrupt the following
programs to add or remove a piece of
laundry.
^ Use the a button to open the door.
^ Add or remove the piece of laundry.
^ Close the drum door.
The program will continue
automatically.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent
Only use laundry detergent formulated
for front loading washing machines.
Water hardness
Hardness
level
Water
quality
Water
hardness hardness
in mmol/l
0 - 1.3
German
For wool and wool blend fabrics use a
detergent formulated for wools.
in °d
0 - 7
I
soft
Follow instructions on the detergent
packaging for the correct use and
amount of detergent.
II
moderate
1.3 - 2.5
over 2.5
7 - 14
III
hard to
very hard
over 14
The amount of detergent used
depends on the level of soiling:
Water softener
If the water hardness level is between II
and III, you can soften the water to
reduce detergent consumption.
Light soiling
No soiling or stains are visible.
Normal soiling
Some visible soiling or a few light
stains.
The detergent packaging should
indicate the correct amount to use in
your machine. Add the detergent, then
add the water softener. From then on
you can then use the recommended
amount of detergent for water hardness
level I.
Heavy soiling
Very visible soiling or stains.
The size of the load and the water
hardness level in your area have an
impact on the amount of detergent
necessary to obtain optimum wash
results. If you do not know the water
hardness level in your area, contact
your local water authority.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Detergent
Fabric softener, liquid starch
Separate starch
Fabric softener added to the wash
program will make fabrics feel softer
and will reduce static cling in the dryer.
^ Dispense the amount of starch
recommended on the packaging.
^ Select the Extra "Starch" before
Liquid starch is a synthetic starch wash
used to give fabrics some stiffness.
Starch can be included in any wash
program as part of the final rinse.
starting a program.
The program and the remaining time
will stop. The display shows "Starch".
^ Dispense the starch directly in the
drum.
Automatic dispensing of fabric
softener or liquid starch
^ Select a spin speed and confirm or
press the "Start" button.
^ Add the fabric softener or liquid
starch to compartment §. Do not
exceed the Max. level mark.
Dye removers / Fabric dyes
Do not use dye removers in this
washer.
^ When dying fabrics in the washer,
adhere to the manufacturer’s
instructions.
External dispensing
The washer is set up for connection to
an external detergent dosage system.
A conversion kit is necessary which can
be purchased from Miele.
The softener or liquid starch is auto-
matically dispensed in the final rinse. At
the end of the program a small amount
of water remains in the fabric softener
compartment §.
If starching frequently, clean the
dispenser compartment and especially
the siphon tube and conditioner
channel. See "Cleaning the detergent
drawer".
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Care
,Before cleaning the appliance,
disconnect the power supply by
unplugging the unit or manually
tripping the circuit breaker.
,Do not use chemical solvents,
abrasive cleaners, glass or all
purpose cleaners. These can
damage plastic surfaces and other
parts.
Cleaning the washer
^ Pull out the detergent drawer as far
as it will go. Press down on the red
release lever and pull the drawer out
of the machine.
^ Clean the exterior of the washer with
a mild solution of non-abrasive
detergent or soap and water. Wipe
dry with a soft cloth.
^ Clean the drum with a stainless steel
cleaner specially formulated for use
in a washing machine.
Cleaning the detergent drawer
Detergent residue should be cleaned
out regularly.
^ Clean the detergent drawer with
warm water.
^ Clean the siphon tube.
1. Remove the siphon tube from the
compartment § and rinse under warm
water. Clean the pipe on which the
siphon tube is attached.
2. Replace the siphon tube.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and Care
Cleaning the inlet hose filter
Slowly turn on the faucet and check
for leaks. If water leaks, tighten the
bolt.
The washer has two water inlet filters to
protect each inlet valve. Check and
clean these filters every 6 months. This
may have to be done more frequently
with some water supplies.
Cleaning the filter in the inlet valve
^ Using pliers carefully loosen and
remove the plastic hose connector
from the inlet valve.
Cleaning the inlet hose filters
^ Turn off the water faucet.
^ Unscrew the inlet hose from the valve
by turning the connector
counterclockwise using a wrench if
necessary.
^ Using needle nose pliers, remove the
plastic filter by pulling on the bar (see
illustration). Rinse under running
water and return. Replace the filter
and seal then reconnect the hose.
^ Remove the rubber seal, 1, from the
connector.
Both filters must be put back in
place after cleaning.
^ Using needle nose pliers, grasp the
plastic filter, 2, and pull it out of the
hose connector.
^ Clean the filter under running water
and carefully remove any large
particles.
^ Replace the filter and seal and
reconnect the hose.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
,Repairs to electrical appliances must only be carried out by a qualified and
trained person in accordance with local and national safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held responsible for unauthorized work.
The following section will help you avoid placing a service call by identifying
issues you may encounter while operating the machine:
A wash program cannot be started
Issue
Possible fault
Solution
Possible fault
The display remains off. The washer has no
power.
– the washer is connected to
the electrical supply,
– the circuit breaker has not
tripped.
Upon selecting the
program "Spin" the
The instructions in
"Before using for the described in the "Before using
Follow the instructions as
program does not start. first time" were not
for the first time" chapter.
followed.
The display shows a
foreign language.
As long as an error
message is
– Regard the display
messages.
displayed, a program
cannot be started.
– Confirm by pressing the jog
shuttle.
The display is dark and The machine goes
the "Start" light flashes into "Standby". The
Press any direct select button.
The Standby function will be
ended.
slowly.
display shuts off to
save energy.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
General problems with the washer
Issue
Possible cause
Solution
The washer shakes
during the spin cycle.
The four feet are not
resting evenly on the
floor.
Level the machine (see
"Installation
Instructions-Leveling the
washer").
There are unusual
sounds coming from
the drain pump.
There is no fault. Lapping sounds at the beginning
and end of the pump process are normal.
Large residues of
The water pressure is too – Check and clean the
detergent remain in the low.
dispenser drawer
filters in the water inlet
hoses.
– Select the "Water plus"
Extra if desired.
Water softening
Clean the detergent
detergent additives tend drawer. In the future add
to clump.
the detergent first and then
the water softener to the
compartment.
The fabric softener is
not completely
The siphon tube is either Clean the siphon tube, see
incorrectly positioned or "Cleaning and care-
dispensed or too much clogged.
water remains in the
Cleaning the detergent
dispenser drawer".
compartment §.
The display shows a
foreign language.
A different language was Select the desired
selected under
language. The flag symbol
leads you to the setting.
"Settings-Language J".
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
Poor wash results
Issue
Possible cause
Solution
The laundry does not
get clean with liquid
detergent.
Liquid detergents do
not contain bleaching
agents. Fruit, coffee
and tea stains may not
be removed.
– Use powder bleach.
– Fill compartment j with
powder bleach and use a
dispenser ball for the
liquid detergent.
– Never put liquid
detergent and bleach
together in the same
wash compartment.
Laundry has a gray
sticky residue.
– Not enough
– Add more detergent to
laundry with grease
stains or use a liquid
detergent.
detergent was used
to dissolve greasy
deposits in heavily
soiled laundry.
– The laundry was
soiled with grease
(oils, lotions).
– Run a 140°F program
with liquid detergent to
clean the washer before
using it for laundry again.
There is white detergent The detergent was not – After drying, remove
residue on dark laundry. completely dissolved
because of hard water.
white residues with a
clothes brush.
These residues are
difficult to remove.
– In the future, use liquid
detergent.
Items with greasy
– Add a Pre-wash to the program. Use liquid
soiling are not clean
after a wash program.
detergent for the pre-wash.
– Use a powder detergent for the main wash.
Use detergent which is specially formulated for
heavily soiled work clothes. Contact the detergent
manufacturer for more information.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
The door will not open when the "Door" button is pressed
Issue
Solution
The washer has no power. Insert the plug into the outlet and the circuit
breaker.
Power failure
To open the drum door, see "Frequently asked
questions - Opening the drum door during a power
failure...".
The door was not
properly closed.
Push the drum door on the locked side. Then press
the "Door" button.
There is still water in the Clean the drain filter and the drain pump as
drum and the washer
cannot drain it away.
described in "Frequently asked questions -
Opening the drum door during a power failure...".
As a safeguard against scalding, the drum door cannot be opened if the wash
water temperature is over 55°C.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
Opening the door during a
power failure or when the drain
is blocked
Machines with a drain pump
If the main drain hose is clogged, water
will be retained in the machine (max.
6.5 gal [30 l]).
,Disconnect the machine from the
power supply.
,Caution: If laundry has been
washed at a high temperature, the
water draining out of the machine
will still be hot! Stop and allow it to
cool before proceeding.
^ Open the detergent dispenser
drawer.
^ Place a 2 quart capacity container
under the drain tube.
^ Remove the tool.
^ Turn the lint trap lid counterclockwise.
Do not remove it. About 2 quarts of
water will drain out of the hose.
If additional water remains in the
machine, tighten the lint trap lid and
empty the container. Repeat as
necessary.
^ Open the lint trap door.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
Once the flow of water stops:
If the drain filter is not tightened
securely water will leak out when the
machine is used.
Open the drum door
,Always make sure the drum is
stationary before reaching into the
drum to remove laundry. A moving
drum is extremely dangerous.
^ Remove the lint trap lid.
^ Remove any foreign objects or lint
from the filter.
^ Insert a screwdriver into the notch,
next to the lint trap, pull it down. The
door will now open.
^ Check that the impeller (in the back
of the chamber) rotates freely by
spinning it with your hand.
^ Return the lint trap lid and tighten into
place.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
Machines with a drain valve
Open the drum door
,Always make sure the drum is
stationary before reaching into the
drum to remove laundry. A moving
drum is extremely dangerous.
^ Press the lever for the emergency
drain down and hold until you hear
no more water running out.
^ Insert a screwdriver into the notch,
next to the lever, pull it down. The
door will now open.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
Changing the light bulb
A burnt out light bulb will not affect the
performance of the washer.
^ Disconnect the power supply to the
work area by unplugging the unit,
tripping the circuit breaker or
removing the fuse.
^ Open the detergent dispenser
drawer. Remove the tool from the rear
side of the panel.
^ Press together the hooks of the
plastic fitting, 2, to separate it from
the bulb,1.
^ Open the drum door.
^ Replace the bad light bulb with a
new one.
A replacement bulb can be obtained by
contacting Miele.
The light bulb must not exceed the
maximum wattage listed on the data
plate.
^ Insert the light bulb into the plastic
fitting.
^ Insert the drum lighting in the socket
and turn clockwise.
^ Insert the tool into the slit of the light
bulb, turn counterclockwise until
resistance is felt.
To use the washer it is absolutely
necessary to have the light bulb
properly installed.
^ Pull out the drum lighting.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
Repairs
PC Update
In the event of a fault which you cannot
fix yourself, please contact the Miele
Technical Service Department.
The indicator marked PC allows a
technician to make use of new
technology if new programs are
developed or new fabrics are
introduced.
l
1 800 565-6435
When contacting the Technical Service
Department, please quote the model
and serial number of your appliance.
Both can be found on the data plate
visible above the front glass on the
inside of the door.
Optional accessories
Optional accessories are available at
your Miele dealer or Miele.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Front view
a Water intake hose cold
b Water intake hose hot
c Electrical connection
d Control panel
g Access panel to drain filter, drain
pump and emergency door release
h Height adjustable feet
i Stand
j Retaining clips (for concrete stand)
k Recessed grip
e Detergent dispenser drawer
f Drum door
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Rear view
a Lid with transport grips
b Mounting for:
d Shipping struts with rotary protectors
e Water intake hose (cold)
f Water intake hose (hot)
– Water intake hose
– Drain hose
g Drain hose for drain pump
h Drain hose for drain valve
i Height adjustable feet
– Withdrawn shipping struts
c Power cord
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Washer/ Dryer Stack
Installation on a base
Height:
The machine can be installed on a steel
base open or closed, or be installed on
a concrete base.
Stacking kit with pull out shelf
66 15/16" (170 cm)
The Miele washing machine can be
installed as part of a washer-dryer
stack in combination with a Miele
tumble dryer. An appropriate stacking
kit* is required.
^ Secure the two front feet of the
washer with the supplied retaining
clips when installing on a concrete
base.
^ Read the supplied Installation
Installation of the stacking kit must be
provided by a Miele Service Technician.
manual.
Coin mechanism
Reinstallation of the machine lid
The dryer can be equipped with a coin
mechanism*.
When reinstalling the appliance lid,
check the firm fit of the cover at the rear
bracket for a safe transport of the dryer.
The reprogramming necessary for the
coin mechanism must be done by a
Miele Service Technician.
Empty the coin mechanism regularly.
Coins or tokens may get jammed.
Do not install devices to auto-
matically turn the washer off, i.e. a
clock timer.
* Available from your Miele dealer or
Miele.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation site
Installation
^ Use the front washer feet and the rear
excess end to transport the washer
from its shipping pallet to the
installation site.
Do not lift the washer by the drum
door.
The washer cannot be built-in.
,Do not install the machine
directly next to or over an open floor
drain or drain channel. Moisture can
penetrate the machine and damage
electrical parts.
,Ensure that the machine’s feet
and the floor are dry to prevent
slippage during the spin cycle.
A concrete floor is the most suitable
surface for the washer. Concrete floors
are less prone to vibration during the
spin cycle than wooden floors.
Removing the shipping struts
^ Remove the left and right rotary
protectors.
,If the machine is installed on a
masonry or concrete base it must
be secured with retaining clips to
prevent the washer from vibrating off
the stand during the spin cycle.
^ The machine must be leveled and
securely positioned.
^ To avoid vibration while spinning, the
machine should not be installed on
soft floor coverings.
In case the installation must be on a
wooden joist floor:
^ Install the unit on a 27 9/16" x 23 5/8" x
1 3/16" (70 x 60 x 3 cm) plywood
base. Ideally the base should be
large enough to span several joists
and should be anchored to the joists
and not just the floor boards.
1. Unhook the rotary protector with a
screw driver.
2. Remove the rotary protectors.
It is best to install the washer in the
corner of a room, where the stability of
the floor is at its greatest.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
^ Turn the left shipping strut
counterclockwise 90° with the
enclosed combination wrench.
^ Turn the right shipping strut
counterclockwise 90° with the
enclosed combination wrench.
^ Pull the shipping strut out.
^ Pull out the shipping strut out.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
,Movement of the washer without
the shipping struts in place should
be kept to a minimum. The shipping
struts should be stored on the back
of the washer for future use. They
must be reinstalled before moving
the machine.
Installing the shipping struts
^ Reinstall the struts by reversing the
installation procedure.
^ Close the holes with the rotary
protectors and their caps.
^ Fasten the shipping struts at the rear
side of the washer. Take care to insert
the drill holes, b, into the clamps, a.
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Leveling the washer
Adjust the four leveling feet
The washer is leveled by adjusting the
four feet. The machine is boxed with the
feet completely screwed in.
To ensure smooth operation the washer
must be level.
Failure to level the machine can result
in increased water and energy
consumption as well as the washer
"banging" during the spin cycle or
"walking" across the floor during use.
^ Turn the locking ring, 2, counter-
clockwise with the enclosed
combination wrench. Unscrew each
of the four feet as much as necessary
by turning both the foot, 1, and the
locking ring, 2, to the left.
^ Check that the machine stands level.
^ Once level, hold the foot, 1, steady
with a wrench. Turn the locking ring,
2, with the combination wrench
towards the machine.
,All four locking rings must be
tight against the bottom of the
machine. In addition, check to see
that the feet were not inadvertently
unscrewed while tightening the
rings. Running a machine that is not
level or whose feet are not tight may
cause damage to both the machine
and its surrounding area.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Water connection
Maintenance
Replace the water hoses only with
genuine Miele hoses.
Cold water connection
A water faucet with 3/4" threat must be
provided on-site. If none is available the Extension hoses
machine must be connected to a water
line by a qualified plumber.
Extension hoses (8’ 2" or 13’ [2.5 m or
4 m]) may be obtained from Miele.
The water pressure must be within
14.5 -145 psi (1 -10 bar). If the water
pressure is greater than 145 psi
(10 bar), a pressure reducer must be
installed. If the water pressure is below
15 psi (1 bar), there will not be enough
water available for a complete fill.
The cold water hose (blue mark) is
not suitable for a hot water
connection.
^ Connect the cold water intake hose
(blue mark) to the cold water valve.
^ Turn on the valve(s) and check for
leaks.
The water intake hoses are
equipped with screen filters. Do not
remove these filters except for
cleaning.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Hot water connection
If the washer is not to be installed for
hot water connection, the settings "Main
wash", "Pre-wash" and "Rinse" must be
adjusted respectively. The hot water
intake hose must be removed.
Connecting the machine to a hot water
ring line will lead to low electrical
consumption during hot water
operation. The hot water temperature at
the water faucet must not exceed 158°F ^ Select in "Settings - Operator level"
(70°C).
the respective options "cold".
The water in single water lines from the
hot water source cools faster when not
in constant use. To heat the wash water
more electricity must be used. The
same conditions for the hot water as for
the cold water connection will then
apply.
The program times may be
extended.
^ Unscrew the hot water intake hose
(red mark).
^ Screw on the supplied stopper.
^ Connect the hot water intake hose
(red mark) to the water faucet.
The connection of the machine to a
hot water line only, is not possible for
functional reasons.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Drainage
If necessary the drain hose can be
extended up to 16' 5" (5 m). The hose
extension can be purchased from your
Miele dealer or Miele.
Drain valve
The machine is drained with a
motorized drain valve. A connection
can be made to an on-site floor drain
(gully with an air gap) on an angle.
The drain pump must be replaced for
drain heights over 3 ft (1 m). The
maximum allowable drain height is 5 ft
11 in (1.8 m). A stronger pump for
these heights can be purchased from
your dealer or Miele.
Drain pump
The wash water is drained using a
pump with a 3 ft (1 m) delivery height.
Make sure there are no kinks in the
drain hose. The elbow on the end of the
drain hose can be turned or removed if
necessary.
Possible connections:
1. Directly into a sink: Hook the hose
over the edge of the sink and secure
it firmly (e.g. by tying the hose to the
water faucet).
2. To a stand pipe: Place the drain
hose into a 11/2" (4 cm) stand pipe
and secure it firmly.
3. To a floor drain: The machine is
equipped with an air gap/
anti-siphoning system so that no
minimum drain height is required.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Electrical connection
,This installation should be
performed by an experienced and
qualified technician, in accordance
with local codes and regulations.
The washer comes with a power cord
without a plug.
The machine is supplied as standard
for connection to a 208 V, 60 Hz, 20 A,
3-phase electrical supply.
For extra safety it is advisable to install
a residual current device (RCD) with a
trip current of 30 mA.
The machine must only be connected
to the voltage and frequency shown on
the data plate.
,To convert the machine to
another electrical connection,
please read the converting manual
on the wiring diagram inside of the
washer. The conversion must be
performed by a Miele Service
Technician. Additionally the "Heating
level" setting must be adjusted.
,Do not install devices to
automatically turn the washer off,
i.e. a clock timer.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Data
Height
85 cm
Width
59.5 cm
72 cm
Depth
Depth with the door open
Weight
112 cm
109 kg
Maximum floor load
Capacity
2778 Newton (approx. 278 kg)
6.5 kg dry laundry
see data plate
Fuse rating
Rated load
Fuse rating
see data plate
see data plate
Noise level during spinning
(Noise emission 3. GSGV)
< 70 dB(A)
Minimum water flow pressure
Maximum water pressure
Length of intake hose
14.5 psi (1 bar)
145 psi (10 bar)
1.6 m
Length of power cord
1.6 m
Drain height maximum (Drain pump)
Light bulb for drum light
1 m
Type G4 (5 Watts/12 Volt)
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Help to protect the environment
Disposal of the packing
materials
Disposal of an old appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
The cardboard box and packing
materials protect the appliance during
shipping.
Ensure that the appliance presents no
danger to children while being stored
for disposal. Before discarding an old
appliance, unplug it from the outlet, cut
off its power cord and remove any
doors to prevent hazards.
To prevent suffocation of children
ensure that any plastic wrapping, bags,
etc. are disposed of safely and kept out
of the reach of children.
Please recycle.
56
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings J
to adjust standard settings
The washer electronic can be adjusted to changing demands with the settings.
The settings can be changed at any time.
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings J
Opening the menu Settings
1
Cottons Uni.
Minimum iron
Delicates
60°C
40°C
40°C
30°C
Program selection
2
3
4
Settings
F
Woollens H
12:00
^ Select the "Settings" J in the main menu and confirm by
pressing the jog shuttle.
Selecting Settings
Settings
BackA
Language F
Water plus
Suds cooling
H
^ Select the settings to be changed and confirm.
If no selection was made in the sub-menu, the display will
switch back to the "Settings" menu after 20 seconds.
Leaving the Settings menu
^ Press "Back" and confirm. The display shows the main
menu.
58
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings J
Language J
Suds cooling
The display contents can be shown
in different languages.
Cold water is added at the end of
the main wash to cool the wash
water.
The displayed language can be set in
the sub-menu "Language" J.
Suds cooling is carried out when a
wash temperature of 70°C or more is
selected.
^ Select the desired language and
confirm with "OK".
Suds cooling should be activated when
the drain hose is hung into a sink, to
prevent scalding.
The flag behind the word "Language" is
a guide to find the settings menu in
case a foreign language is shown.
Suds cooling is factory set turned on.
If the language setting was changed, it
is only valid for the current wash
program. Once the program ends, the
display will show the language which is
set under "Settings - Supervisor level".
Water plus
In the setting "Water plus" you can
select an extra setting from below.
Water plus
The water level increases (more water)
in the wash and rinse cycles of the
program (delivery status).
Additional rinse
An extra rinse cycle is added in the
programs "Cottons Hygiene", "Cottons
Uni." and "Minimum iron".
Water+ and Add. rinse
The water level is increased in the wash
and rinse cycles and an extra rinse
cycle is added to the programs
"Cottons Hygiene", "Cottons Uni." and
"Minimum iron".
59
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings J
Time of day
Contrast
The selection allows the clock to be
shown as 24 hours, 12 hours or not
at all. The time of day is also set
here.
The contrast of the display can be
set in ten different levels.
The machine is factory set to level 4.
The contrast changes immediately
when a different level is selected.
If the clock is not selected the delay
start can only be shown only as a 24
hour clock timer. The display will how
the timer counting down until the start
of the program but not he current time
of day.
^ Confirm the setting with the jog
shuttle.
Brightness
Selecting the clock
^ Select the clock display and confirm.
The brightness of the display can be
set in ten different levels.
The display changes to the time of day
setting.
The machine is factory set to level 5.
Set the time of day
The brightness changes immediately
when a different level is selected.
^ Select the current hour with the jog
shuttle and confirm. Repeat with
setting the minutes and confirm.
Press again to save the time of day.
^ Confirm the setting with the jog
shuttle.
60
Download from Www.Somanuals.com. All Manuals Search And Download.
Settings J
Standby
Memory
The display goes out after 10
minutes and the "Start" button
flashes slowly to save energy.
The Memory function remembers the
addition of an extra feature to a
program, a change in spin speed or
the temperature the next time that
program is selected.
On
The display will go into Standby mode:
Once the wash program is selected
again the washer shows the saved
options.
– if no program was selected after the
machine was turned on.
The memory function is not active when
favorites are selected with the direct
select buttons.
– after a program has started.
– at the end of a program.
The Memory function is factory set "off".
Not in current prog.
(Factory default)
The Standby function will be turned on
if no program was selected after the
machine was turned on.
Temperature unit
The temperature can be shown in
"°C/Celsius" (factory default) or
"°F/Fahrenheit".
By turning the jog shuttle or pressing
any button the display is turned on
again.
The delivery status is "°C".
61
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
The menu Settings - Supervisor level must be activated
by the Technical Service.
The menu "Settings" (except Languages J) is locked with a
code to prevent unwanted access.
Selecting Settings
Settings
BackA
Language F
Supervisor level
^ Select "Supervisor level" and confirm.
Settings
BackA
Supervisor level
Access via code
^ Select "Access via code" and confirm.
Entering the code
Enter the code "0 0 0" (factory default). If the code is entered
wrong three times, the code entry will be locked for 1 hour.
0
_ _
Enter code
^ Turn the jog shuttle until the first digit shows. Confirm the
digit. Enter the second and third digit.
62
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
Confirming the code
0 0 0
Confirming the code
OK
H
Back A
H
^ Confirm the entered code.
W
Entry OK
Menu opened
The user is now in the "Supervisor level". The previously
described and all the following settings can be changed.
Change the code to prevent unauthorized access to the
settings.
63
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
Language J
Language menu
The display contents can be shown
in different languages.
This option allows you to display an
additional welcome screen which
requests a language selection. The
screen can be shown before the
main menu or after the end of a
wash program.
The fixed default language can be set
in the sub-menu "Languages J".
^ Select the desired language and
confirm with "OK".
Two options can be selected:
– International: Welcome screen
shows, an additional language has to
be selected.
Sort languages
– National: no additional welcome
screen (factory default).
The language order can be set,
when the option "Language access -
international" is selected.
Intensive Water plus
Supervisor level
You can select this option if the
Extras "Intensive" and "Water plus"
are shown in the menu "Extras".
The access code for the operator
level can be changed.
The option is factory set "off".
^ Enter the old code.
^ Enter the new code.
Once the new code is confirmed, the
display will show the beginning of the
"Settings" menu.
Save
The option "Save" can be shown in
the main menu. The function "Save"
is needed to save for example the
favorite wash programs on the direct
select buttons.
The machine comes factory set with
this option turned off.
64
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
Auto load control
Main wash water
The washer has a Auto load control.
The water levels and the program
running times are adjusted to the
load size. If the load size automatic
is turned off the program will always
run as if for a full load.
The water type for the main wash
can be selected (except for the
programs "Woollens", "Silk" and
"Curtains"). The hot water intake will
be only accessible at a wash
temperature of 30°C or higher.
The machine comes factory set with
this option turned on.
The machine comes factory set with the
water type "hot".
If the washer is not connected to hot
water, the program running times will
be extended and vary from the
displayed remaining times.
Pre-wash water
The water type for the pre-wash can
be selected (except for the program
"Curtains"). The hot water intake will
be only accessible at a wash
temperature of 86°F (30°C) or
higher.
If "Industrial water" is used, the
washer must be refitted accordingly.
The machine comes factory set with the
water type "hot".
Rinse water
The water type for the rinse in the
programs "Cottons Hygiene",
"Cottons Uni.", "Minimum iron", "Table
linen", "Kitchen linen", "Towelling"
and "Sluice" can be selected. The
hot water intake will be only
accessible at a wash temperature of
50°C or higher.
The machine comes factory set with the
water type "hot".
If "Industrial water" is used, the
washer must be refitted accordingly.
65
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
Water level Cottons
Pre-wash duration
The program "Cottons Hygiene" and
"Cottons Uni." allows you to increase
the water level for the main wash.
The wash time for the pre-wash can
be extended.
The machine comes factory set with the
The machine comes factory set with the option block parameter selected. (The
option block parameter selected. (The
water level will be controlled according
to the factory set program data.)
water level will be controlled according
to the factory set program data.)
Wash time Cottons
Water level Min. iron
The programs "Cottons Hygiene"
and "Cottons Uni." allow to increase
the water level for the main wash.
The program "Minimum iron" allows
to increase the water level for the
main wash.
The machine comes factory set with the
The machine comes factory set with the option block parameter selected. (The
option block parameter selected. (The
water level will be controlled according
to the factory set program data.)
water level will be controlled according
to the factory set program data.)
Min. iron
Pre-wash temp. Cot.
The program "Minimum iron" allows
to extend the wash time for the main
wash.
The Pre-wash temperature for the
programs "Cottons Hygiene" and
"Cottons Uni." can be selected.
The machine comes factory set with the
The machine comes factory set with the option block parameter selected. (The
option block parameter selected. (The
water level will be controlled according
to the factory set program data.)
water level will be controlled according
to the factory set program data.)
66
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
No. of programs
Disinfection
Additional programs can be added
to the program selection.
Special disinfection programs can
be added.
0 Additional programs (factory default) 0 Additional programs (factory default)
4 Additional programs ("Table linen",
"Pillows", "Curtains" and "Kitchen
linen")
4 additional programs (Thermal
disinfection 15 min/85°C, Chemo
thermal disinfection 10 min/70°C,
Chemothermal disinfection 20
min/60°C and Chemothermal
disinfection 30 min/40°C).
2 Additional programs ("Outerwear"
and "Waterproofing")
6 Additional programs (all of the
above).
Pre-wash
In the programs "Cottons Hygiene",
"Cottons Uni." and "Minimum iron"
you can select to permanently add a
pre-wash to the cycle or to select it
in the menu "Extras".
Hygiene
If the last used program had a
temperature of 55°C or less, the
display shows the request to start
the "Hygiene" program.
The machine comes factory set with the
option "Menu selection" activated.
The machine comes factory set with
this option turned off.
2. Pre-wash Kitchen linen
Sluice
The program "Kitchen linen" allows
an additional pre-wash.
When the option is selected the
sluice programs are offered
additionally.
Add the detergent for the additional
pre-wash directly in the drum.
The machine comes factory set with
this option turned off.
The machine comes factory set with
this option turned off.
67
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
Optimize energy
Pre-rinse Cottons
The energy use for the programs
"Cottons Hygiene", "Cottons Uni."
and "Minimum iron" is at its optimum
when this option is turned on.
The programs "Cottons Hygiene"
and "Cottons Uni." allows you to add
a pre-rinse of the laundry.
The machine comes factory set with
this option "off".
The machine comes factory set with
this option "on".
Pre-rinse Min. iron
No. rinses Cottons
The program "Minimum iron" allows a
pre-rinse of the laundry.
The programs "Cottons Hygiene"
and "Cottons Uni." allow you to
change the number of rinse cycles.
The machine comes factory set with
this option "off".
2 rinses (factory default)
3 rinses
4 rinses
5 rinses
Spin free of charge
When operated by a coin
mechanism, the program "Spin" can
be activated free of charge.
No. rinses min. iron
The machine comes factory set with
this option "off".
The program "Minimum iron" allows
you to change the number of rinses.
2 rinses (factory default)
3 rinses
4 rinses
68
Download from Www.Somanuals.com. All Manuals Search And Download.
Menu Settings - Supervisor level
No detergent
Leaving the Settings menu
^ Press "back" and confirm. The
display shows the main menu.
If an external dispensing system is
fitted to the machine it will not be
accessed if "No soap" is selected.
You have the option to show the
Extra "No Soap" in the menu "Extras".
The machine comes factory set with
this option "off".
External dispenser
The washer is set up for connection
to an external dispensing system. To
use the external dispensing system
the setting must be adjusted/set
accordingly.
The machine comes factory set with
this option "off".
69
Download from Www.Somanuals.com. All Manuals Search And Download.
70
Download from Www.Somanuals.com. All Manuals Search And Download.
71
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / xx05
M.-Nr. 06 523 700 / 00
en - CDN
Download from Www.Somanuals.com. All Manuals Search And Download.
|