Miele Washer Dryer 1119 User Manual

Technical Information  
Date: June 7, 2004  
To: Technical Service  
Subject: Washer/Dryer Stand  
W1113, 1119, 1203, 1213, 1215  
T1302, 1303, 1322C, 1323C, 1329C, 1403, 1405  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Washer Stand Installation  
Drain the unit, before laying it on its side.  
Remove the shipping struts  
Lay the washer on its right side. Be sure to lay the unit on a flat, soft underlay (i.e. carpet)  
Remove the washers feet  
Using the threaded studs and nuts provided (M10), screw 2 nuts midway onto each threaded stud.  
Screw the threaded studs (M 10) into the washer and tighten them see Fig. 5.  
Install a washer (10.2 x 32 x 2) on each threaded stud.  
Fit the stand onto the studs.  
Install a washer (10.5) on each threaded stud.  
Screw a nut (M 10) on each threaded stud and tighten.  
Stand the washer upright  
Install the washer stand rear panel using the 4 Torx screws provided see Fig. 3.  
Place the washer into its final position.  
Insert the 2 rubber bushings into the side holes of the washer stand. Install a washer and nut on each  
and tighten the nut see Fig.6.  
Dryer Stand Installation  
Drain the unit, before laying it on its side.  
Lay the dryer on its right side. Be sure to lay the unit on a flat, soft underlay (i.e. carpet)  
Remove the dryers feet  
Using the threaded studs and nuts provided (M8), screw 2 nuts midway onto each threaded stud.  
Screw the threaded studs (M 8) into the dryer and tighten them see Fig. 7.  
Install a washer (8.5 x 30 x 2) on each threaded stud.  
Fit the stand onto the studs.  
Install a washer (8.4) on each threaded stud.  
Screw a nut (M 8) on each threaded stud and tighten.  
Stand the dryer upright  
Install the dryer stand rear panel using the 4 Torx screws provided see Fig. 3.  
Place the dryer into its final position being sure to line up the studs of the rubber bushings with the holes  
on the dryer stand.  
Once the stands are together and in their final positions install a washer and nut onto each stud and  
tighten the nut see Fig.6.  
Install the caps into the open holes on the sides of the washer and dryer stand see Fig. 8.  
Leveling  
Once the washer and dryer (with stands) are in their locations. Adjust the feet until the stands are level. Tighten  
the counter nuts.  
Installing the Drawers  
Pull out the stand drawer rails as far as possible.  
Place the drawer on the rails and close the drawer, see Fig. 2.  
The drawer locks into position automatically when it is closed.  
Open the drawer as far as possible then close it to check that it functions correctly  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Moxa Technologies Switch NPort 6110 User Manual
Multi Tech Systems Network Card MT5634IND User Manual
Nikon Camcorder Coolpix 8800 User Manual
NordicTrack Treadmill NTTL15021 User Manual
Onkyo DVD Player DV CP500 User Manual
Onkyo DVD Player DV CP802 User Manual
Ozark Trail Tent WMT 9900 User Manual
Packard Bell Computer Drive DVX 460 User Manual
Panasonic Home Security System Bb Hca1a B User Manual
Paradyne Network Card 3825 A2 GX40 00 User Manual