Miele Ventilation Hood DA252 3 User Manual

Operating and installation instructions

Ventilation System

DA 251

DA 252-3

DA 259-3

To prevent accidents

and machine damage,

read these instructions

before

installation or use.

M.-Nr. 05 802 960

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Read these Operating Instructions carefully before installing or

using the Ventilation System.

This appliance is designed to vent

cooking smoke and odors only.

This appliance is intended for

residential use only. Use the

appliance only for its intended

purpose. The manufacturer cannot

be held responsible for damages

caused by improper use of the

hood.

Be certain your appliance is

properly installed and grounded by

a qualified technician.

To guarantee the electrical safety of this

appliance, continuity must exist

between the appliance and an effective

grounding system. It is imperative that

this basic safety requirement be met. If

there is any doubt, have the electrical

system of the house checked by a

qualified electrician. The manufacturer

can not be held responsible for

damages caused by the lack, or

inadequacy of, an effective grounding

system.

This appliance complies with current

safety requirements. Improper use of

the appliance can lead to personal

injury and material damage.

READ AND SAVE THESE

INSTRUCTIONS

Before connecting the appliance to

the power supply make sure that

the voltage and frequency listed on the

data plate correspond with the

household electrical supply. This data

must correspond to prevent machine

damage. Consult a qualified electrician

if in doubt.

CAUTION

For General Ventilating Use Only.

Do Not Use To Exhaust Hazardous

Or Explosive Materials And Vapors.

Installation work and repairs should

only be performed by a qualified

technician in accordance with all

applicable codes and standards.

Repairs and other work by unqualified

persons could be dangerous and the

manufacturer will not be held

responsible.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

This equipment is not designed for Use

maritime use or for use in mobile

Do not allow children to play with

installations such as caravans or

aircraft. However, under certain

conditions it may be possible for an

installation in these applications. Please

contact the nearest Miele dealer or the

Technical Service Department with

specific requirements.

or operate the appliance or its

controls. Supervise its use by the

elderly or infirm.

Be careful when preparing a

flambé beneath the hood.

Flames may be drawn up into the hood

by the suction or grease filters may

catch fire.

Before servicing or cleaning the

unit, switch power off at the service

panel and lock the service

disconnecting means to prevent power

from being switched on accidentally.

When the service disconnecting means

can not be locked, securely fasten a

prominent warning device, such as a

tag, to the service panel.

Never operate gas burners without

pots.

Do not leave cooking surfaces

unattended while in use.

Overheated food, oil and grease can

catch fire.

Do not use the hood without the

grease filters in place.

Before discarding an old

appliance, unplug it from the

Clean the grease filters regularly.

Dirty filters are a fire hazard.

power supply and remove the power

cord and any doors to prevent hazards.

Do not use a steam cleaner to

clean the hood. Steam could

penetrate electrical components and

cause a short circuit.

In areas subject to infestation by

cockroaches or other pest, keep

the appliance and its surroundings

clean at all times. Any damage caused

by cockroaches or other pest will not

be covered under warranty.

Always turn on the hood when

using the cooktop to prevent

damage from condensation.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

, WARNING - TO REDUCE

THE RISK OF A RANGE TOP

GREASE FIRE:

, WARNING

TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE,

OBSERVE THE FOLLOWING:

Never leave surface units

unattended at high settings.

Boilovers cause smoking and greasy

spillovers may ignite. Heat oils slowly

on low or medium settings.

SMOTHER FLAMES with a close

fitting lid, cookie sheet, or metal

tray, then turn off the burner.

BE CAREFUL TO PREVENT BURNS.

If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE

DEPARTMENT.

Always turn the hood “ON” when

cooking at high heat or when

cooking flaming foods.

Clean ventilating fans frequently.

Grease should not be allowed to

accumulate on the fan or filter.

NEVER PICK UP A FLAMING

PAN - You may be burned.

DO NOT USE WATER, including

wet dishcloths or towels - a violent

steam explosion will result.

Use proper pan size. Always use

cookware appropriate for the size

of the surface element.

Use an extinguisher

ONLY if:

– You know you have a Class ABC

extinguisher, and you already know

how to operate it.

– The fire is small and contained in the

area where it started.

– The fire department is being called.

– You can fight the fire with your back

to an exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Installation

Any fittings, sealant, or materials

used to install the ductwork must

be made of approved non-flammable

materials.

, WARNING

To reduce the risk of fire only

use metal ductwork.

Never connect an exhaust hood to

an active chimney, dryer vent, vent

flue, or room ventilating ductwork. Seek

professional advice before connecting

an exhaust hood vent to an existing,

When installing the hood, follow the

recommended minimum safety

distances between a Miele cooktop and

the hood:

– 22" (55 cm) above electric cooktops, inactive chimney or vent flue.

– 26" (65 cm) above gas cooktops,

– 26" (65 cm) above an open grill.

Ducted fans must always be

vented outdoors.

Make sure that the airflow in the

room is sufficient for combustion

and exhausting of all non-electric

heating appliances (water heaters, gas

cooktops, gas ovens, etc.), otherwise

backdrafts may occur. Follow the

heating manufacturer’s guidelines and

safety standards or those published by

the National Fire Protection Association

(NFPA), or the American Society for

Heating, Refrigeration and Air

If local building codes require a greater

safety distance, follow their

requirement.

For non-Miele cooking appliances

maintain the safety distances

recommended by the appliance

manufacturer in their instructions.

If there is more than one appliance

beneath the hood and they have

different minimum safety distances

always select the greater distance.

Conditioning Engineers (ASHRAE).

If in doubt, consult an experienced

professional.

Be careful not to damage hidden

electrical wiring or plumbing when

cutting or drilling into the wall or ceiling.

Do not use an extension cord to

connect the appliance to electricity.

Extension cords do not guarantee the

required safety of the appliance, (e.g.

danger of overheating).

Do not install this hood over

cooktops burning solid fuel.

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional description

The ventilation hood works by air

extraction. The air is drawn in and

cleaned by the grease filters and

directed outside.

The hood comes equipped with a

non-return flap. This flap automatically

closes when the hood is turned off so

that no exchange of outside air and

room air can occur. When the hood is

turned on, the air pressure of the

exhaust fan automatically opens the

flap blowing the inside air and cooking

odors outside.

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the appliance

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the appliance

a Chimney extension

b Chimney

k Light button

This button turns the light on and off

and also dims the light.

The lighting can be used independently

of the fan.

c Canopy

d Grease filter

e Overhead lighting

f Indirect lighting

l On/Off button

m Fan power level buttons

Four fan speed selection.

n Delayed Shut Down

g Glass shelves

This button activates the Delayed Shut

Down feature. The fan can be set to

turn off automatically after either 5 or 15

minutes.

Each holds up to 8 lbs.

h Canopy storage surface

Max weight on entire surface not to

exceed 17 lbs.

o Grease filter button

The indicator next to the grease filter

button lights when the grease filters

need to be cleaned. This button is also

used:

i Control panel

j Indirect lighting switch

– to reset the grease filter timer after

cleaning the grease filters (see

"Cleaning and Care").

– to show how long the grease filters

have been in use (see "Operation /

Grease filter timer").

– to change the number of hours

counted by the grease filter timer

(see "Operation / Reprogramming the

grease filter timer").

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Turning on the fan

Delayed Shut Down

If odors or smoke remain in the kitchen

after cooking has been completed, the

Delayed Shut Down feature can be

selected to allow the hood to continue

running for either 5 or 15 minutes.

^ Press the On/Off button.

The fan runs at power level "2".

The On/Off indicator lights.

Selecting the power level

^ Press the Delayed Shut Down button

while the fan is still running.

Press once = 5 minute delay

(left indicator lights)

Press twice = 15 minute delay

(right indicator lights)

^ Use the _ controls to select the

desired power level.

To cancel the Delayed Shut Down

feature press the button again.

& =increases the fan speed

$ =decreases the fan speed

Level "1" to "3" (green indicators) are

usually sufficient for normal cooking.

Intensive setting

Level "4" (yellow indicator) should be

used for a short period when frying or

cooking food with a strong aroma.

Fan performance

The maximum air flow capacity is

625 cfm. Factors such as narrow duct

diameter and bends will affect this

value.

Level 1 operates at 40% capacity

Level 2 operates at 60% capacity

Level 3 operates at 80% capacity

Level 4 operates at 100% capacity

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Turning off the fan

Dimming the lighting

The brightness of the lighting can be

adjusted.

^ While the lighting is turned on, press

the light button.

The lighting will dim until the button is

released.

^ Press the On/Off button to turn the

fan off.

The indicator goes out.

^ If the button is pressed again, the

lighting will brighten until the button is

released.

Automatic Safety Shut Off

The fan will be turned off automatically

10 hours after the last button was

activated. The lighting however, will

remain on.

If the button is pressed continuously,

the light will cycle between bright and

dark.

^ Press the light button again to turn off

the lighting.

^ Pressing the On/Off button will turn

the fan back on.

Indirect lighting

Turning the lighting on / off

The overhead lighting can be turned on

and off independently of the fan.

^ Press the indirect lighting switch to

"I".

^ Press the light button briefly to turn

on the lighting.

The light button indicator illuminates.

^ Press the light button briefly again to

turn off the lighting.

The light button indicator will go out.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Grease filter timer

Checking the grease filter timer

A timer monitors the hours of fan

operation. The indicator for the grease

filter will light after 30 hours of

operation. The grease filters must then

be cleaned.

To check the percentage of time

already used:

After the grease filters have been

cleaned and put in place, the grease

filter timer must be reset.

^ Press the On/Off button to turn the

fan on.

^ To do this, press the grease filter

button for about 3 seconds.

^ Press the grease filter button.

The indicator will go out.

The number of flashing $& indicators

show the percentage of programmed

hours that have been used.

1 indicator = less than 25 %

2 indicators = less than 50 %

3 indicators = less than 75 %

4 indicators = less than 100 %

This information will remain stored in

memory in the event of a power failure.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Reprogramming the grease filter

timer

The grease filter timer is preset to 30

hours. This time can be lengthened or

shortened to 20, 30, 40 or 50 hours.

The indicator for the grease filter and

one of the $& indicators will flash.

– A time of 20 hours should be

programmed in kitchens with

frequent pan or deep frying.

The lit $& indicator shows the

programmed time:

– A time of 20 hours should also be

programmed if the kitchen is only

used occasionally. Otherwise grease

which has accumulated over a long

period of time will harden on the

filters making cleaning more difficult.

1st indicator from the left = 20 hours

2nd indicator from the left = 30 hours

3rd indicator from the left = 40 hours

4th indicator from the left = 50 hours.

^ Use the $ or & button to select the

desired time.

^ Press the On/Off button to turn off the

fan.

^ Store the selection by pressing the

grease filter button.

If the procedure is not stored within

4 minutes of programming, the hood

will automatically default to the "old"

data.

^ Press the Delayed Shut Down and

grease filter buttons at the same time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Stainless steel

Before cleaning or servicing the

hood, disconnect it from the power

supply by either removing the fuse,

unplugging it from the outlet or

manually "tripping" the circuit

breaker.

Stainless steel surfaces can be cleaned

using a non-abrasive stainless steel

cleaner.

To help prevent resoiling, a conditioner

for stainless steel can also be used.

Apply sparingly with even pressure.

Cleaning the casing

Stainless steel colored controls

,^{Never use abrasive cleaners,}

scouring pads, steel wool or caustic

(oven) cleaners on the hood. They

will damage the surface.

These controls may become

discolored or damaged if not

cleaned regularly.

Do not use a stainless steel cleaner

on these controls.

^ All external surfaces and controls can

be cleaned with warm water and

liquid dish soap applied with a soft

sponge.

^ Wipe dry using a soft cloth.

Do not use too much water when

cleaning the controls. Water could

penetrate into the electronics and

cause damage.

^ Glass surfaces can be cleaned using

glass cleaner.

Avoid:

– cleaning agents containing soda,

acids or chlorides,

– abrasive cleaning agents e.g.

powder or cream cleansers,

– abrasive sponges, e.g. pot scourers

or sponges which have been

previously used with abrasive

cleaning agents.

These will damage the surface.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Grease filters

^ Clean the filters

- by hand: use a scrub brush in

warm water with a mild detergent.

- in a dishwasher: place the filters

vertically in the lower basket, making

sure that the spray arm is not

blocked.

The reusable metal grease filters

remove solid particles from the vented

kitchen air (grease, dust, etc).

The grease filters should be cleaned

every 3 - 4 weeks or whenever the

grease filter indicator lights.

Depending on the detergent,

cleaning the grease filters in a

dishwasher may cause permanent

discoloration of the filter surface.

Performance of the filter will not be

affected by this discoloration.

A dirty filter is a fire hazard.

^ After cleaning, the filters can be

placed on a towel to air dry.

^ While the filters are removed, clean

any dirt or grease from the filter

casing to prevent the risk of fire.

When putting the grease filters back

make sure that the locking clips are

visible facing down towards the

cooking surface.

^ To remove the grease filters press the

locking clips in towards the middle of

the filter. Holding carefully, lower and

remove the filter.

If the filters are incorrectly installed,

insert a small screwdriver into the slit

along its edge to disengage it from the

casing.

^ After returning the grease filters,

press the grease filter button for 3

seconds to reset the timer. The

indicator light will go out.

^ If the grease filters are cleaned

before the grease filter timer has

reached its maximum, the grease

filter button should be pressed for

6 seconds to reset the counter to

zero.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Changing the light bulbs

Never use the lighting without the

lamp cover, a, in place. The glass is

specially made to filter harmful light

rays.

Before changing the light bulbs,

disconnect the hood from the power

supply by either removing the fuse,

unplugging it, or manually "tripping"

the circuit breaker.

Indirect lighting

When in use halogen bulbs become

extremely hot, and they can burn

your hands. Do not attempt to

change the bulbs until they have

had sufficient time to cool down.

Do not touch the bulb surface.

Fingerprints or body oils deposited

on the bulb will decrease the life of

the bulb. Please follow the bulb

manufacturer’s instructions.

Overhead light

^ Remove the two screws securing the

light cover.

^ Carefully raise the front of the bulb

and pull it out of its socket.

^ Insert the new bulb into the socket

and lower it into its holder.

^ Replace the light cover and the two

screws.

^ To change the halogen bulb first

remove the lamp cover, a.

^ Pull the bulb, b, out of its socket and

replace with a new one.

^ Now return the lamp cover, a.

Download from Www.Somanuals.com. All Manuals Search And Download.

After Sales Service

In the event of a fault which you can not

correct yourself please contact:

– Your Miele Dealer

– The Miele Technical Service

Department

USA 1-800-999-1360

[email protected]

CDN 1-800-565-6435

[email protected]

When contacting the Technical Service

Department, please quote the model

and serial number of your appliance.

These are shown on the data plate

which is visible when the grease filter is

removed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Caring for the environment

Disposal of packing material

Disposal of an old appliance

The cardboard box and packing

materials protect the appliance during

shipping. They have been designed to

be biodegradable and recyclable.

Please recycle.

Old appliances may contain materials

that can be recycled. Please contact

your local recycling authority about the

possibility of recycling these materials.

Before discarding an old hood,

unplug it from the outlet and cut off

its power cord to prevent hazards.

To prevent suffocation of children,

ensure that any plastic wrappings,

bags etc. are disposed of safely and

kept out of their reach.

Download from Www.Somanuals.com. All Manuals Search And Download.

Plywood backing

^ Find the studs to the left and right of

the mounting location by tapping the

wall or using a stud finder.

The majority of the weight of the

installed ventilation system will be

supported by the canopy. Its

mounting bracket must be firmly

attached to the stud framing behind

the drywall. If studs are not located

in the required locations, a plywood

backing (min. ¹/₂" (13 mm) thick)

spanning at least two studs must be

installed. Failure to adequately

support the weight as stated may

result in the ventilation system falling

off the wall, causing personal injury

and property damage.

^ Mark the center of each of the studs

with a vertical line.

Be careful not to damage any wiring

or plumbing that may be located

behind the wall. Make sure that the

power supply to the area being

worked in has been turned off at the

breaker panel before cutting into the

wall.

^ Cut out the drywall along the marked

lines and replace it with plywood of a

matching thickness (min. ¹/₂" (13 mm)

thick). Tape the joints and refinish the

wall.

(If plywood backing is not needed,

proceed to "Appliance dimensions and

Installation")

^ See enclosed installation sheet for

instructions on how to install the

appliance.

To install a plywood backing board

^ Determine and mark the location of

the retaining plate for the canopy as

outlined on the Installation sheet.

^ Make a cutting line 3" (76 mm) above

and 3" (76 mm) below the outline of

the retaining plate.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation accessories

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation accessories

2 protective shields

prevent scratches to the chimney

during installation.

4 screws 5 x 60 mm

4 washers 5.3 mm

2 hose clips for securing the

exhaust ducting.

1 reducing collar

for use with a 5" (125 mm) exhaust

ducting.

1 non-return flap

6 screws 5 x 40 mm

Upper and middle retaining plate (The wall anchors included in the

for securing the chimney extension.

Lower retaining plate for

securing the canopy.

packaging are not for use in

USA/CDN.)

2 M 6 locking nuts for securing the

motor assembly.

4 screws 3.9 x 7.5 mm for securing the

chimney and the chimney extension.

CAUTION:

During the installation process

please be careful of sharp edges

that can cause harm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical data

Important

All electrical work should be

performed by a qualified electrician

in strict accordance with national

and local safety regulations.

Installation, repairs and other work

by unqualified persons could be

dangerous. The manufacturer can

not be held responsible for

The hood comes equippped with a 5 ft

(1.5 m) power cord with a NEMA 5-15

molded plug for connection to a

120 VAC, 60 Hz, 15 A power outlet.

Maximum load

DA 252-3 . . . . . . . . . . . . . . . . . . . 456 W

DA 251, DA 259-3 . . . . . . . . . . . 436 W

unauthorized work.

Lighting

Ensure that power to the appliance

is OFF while installation or repair

work is performed.

DA 252-3 . . . . . . . . . . . . . . . . . 4 x 20 W

DA 251, DA 259-3 . . . . . . . . . . 3 x 20 W

Indirect lighting . . . . . . . . . . . . 2 x 13 W

Voltage . . . . . . . . . . . . . . . . . . . . . 120 V

Frequency . . . . . . . . . . . . . . . . . . 60 Hz

Circuit rating. . . . . . . . . . . . . . . . . . 15 A

Verify that the voltage, load and circuit

rating information found on the data

plate (located behind the grease

filters), match the household electrical

supply before installing the hood.

If there is any question concerning the

electrical connection of this appliance

to your power supply, please consult a

licensed electrician or call Miele’s

Technical Service Department.

USA 1-800-999-1360

CDN 1-800-565-6435

WARNING:

THIS APPLIANCE MUST BE

GROUNDED

Download from Www.Somanuals.com. All Manuals Search And Download.

Appliance dimensions and Installation

Do not install this hood over any

appliance that burns solid fuel stove.

The minimum safety distance

allowed between the top of a Miele

cooking surface and the bottom of

the hood S is:

- 22" (55 cm) above electric cooktops

- 26" (65 cm) above gas cooktops

- 26" (65 cm) above an open grill

For non-Miele cooking appliances

maintain the safety distances

recommended by the cooktop

manufacturer in their installation and

operating instructions.

If there is more than one appliance

beneath the hood and they have

different minimum safety distances

always select the greater distance.

See "Warning and Safety

instructions" for further information.

26" (65 cm) is recommended for all

installations to allow for optimum work

space under the hood.

Read the entire installation procedure

and determine height S before

beginning the installation.

If the hood is fitted flush to the ceiling

make sure that the remaining distance

to the ceiling is not greater or less than

Cut out area in wall or ceiling for

entrance of 6" (150 mm)

ductwork or 5" (125 mm)

appliance height H.

To fit the chimney, distance A between

the top of the chimney and the ceiling

must be at least ⁷/₈" (20 mm).

ductwork with a reducing collar.

Download from Www.Somanuals.com. All Manuals Search And Download.

Appliance dimensions and Installation

If the standard unit height H is not

suitable to the kitchen’s ceiling height,

longer optional chimney extensions are

available from your Miele dealer or

Miele’s Technical Service Department.

Standard unit H. . . . . . . . 28 ³/₄" - 44 ⁷/₈"

. . . . . . . . . . . . . . . . 730 mm - 1140 mm

DATK 252/259 - 850 . . . . . . 44 ⁷/₈" - 61"

. . . . . . . . . . . . . . . 1140 mm - 1549 mm

Download from Www.Somanuals.com. All Manuals Search And Download.

Air extraction

Exhaust ducting and connections

,^WARNING

– The ducting should be as short and

straight as possible, and the number

of sharp bends should be minimized.

Danger of toxic fumes.

Gas cooking appliances release

carbon monoxide that can be

harmful or fatal if inhaled.

– For most efficient air extraction, the

diameter of the ductwork should not

be less than 6" (150 mm). Use of flat

ducts also reduces the air extraction

efficiency.

The exhaust gases extracted by

the hood should be vented

outside of the building only.

– Noise levels of the hood will increase

if flat ducts or round ducts of less

than 6" (150 mm) in diameter are

used.

Do not terminate the exhaust

ducts in attics, garages,

crawlspaces, etc.

– Use smooth or flexible pipes made

from approved non-flammable

materials for exhaust ducting.

To reduce the risk of fire, only use

metal ductwork.

– Where the ductwork is horizontal, it

must slope away from the hood at

least ¹/₈" per foot (1cm per meter) to

prevent condensation dripping into

the appliance.

Please read and follow the

"IMPORTANT SAFETY

INSTRUCTIONS" to reduce the risk of

personal injury. Follow all local building

codes when installing the hood.

– If the exhaust is ducted through an

outside wall, a Miele Telescopic Wall

Vent can be used.

Download from Www.Somanuals.com. All Manuals Search And Download.

Air extraction

Condensate trap

Important:

If the ductwork runs through rooms,

ceilings, garages, etc. where

temperature variations exist, it may

need to be insulated to reduce

condensation. In some cases, a

condensate trap may also be required

to collect and evaporate any

condensate which may occur.

When installing a condensate trap,

ensure that it is positioned vertically

and if possible directly above the

exhaust outlet.

– If the exhaust is ducted into an

inactive flue, the air must be expelled

parallel to the flow direction of the

flue.

Never connect an exhaust hood to

an active chimney, dryer vent, vent

flue, or room venting ductwork. Seek

professional advice before

connecting an exhaust hood vent to

an existing, inactive chimney or vent

flue.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alteration rights reserved / 1503

M.-Nr. 05 802 960 / 01

This bio-friendly paper was bleached without the use of chlorine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Nady Systems Network Card MXE 1212 User Manual
NEC Computer Monitor JC 1576VMB User Manual
Nextar Digital Photo Frame Snowman Figurine User Manual
Nikon Camera Lens f 28D ED User Manual
NordicTrack Home Gym NEL70951 User Manual
Onkyo Stereo Receiver TX NR616 User Manual
Opticon Scanner LPN5627 User Manual
Optoma Technology Projector EH500 User Manual
Oregon Scientific Games 086 003875 034 User Manual
Panasonic Cell Phone EB GD93 User Manual