Miele Ventilation Hood DA210 3 User Manual

Operating and installation instructions

Ventilation System

DA 210-3

DA 220-3

To prevent accidents

and machine damage,

read these instructions

before

installation or use.

M.-Nr. 05 853 490

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Read these Operating Instructions carefully before installing or

using the Ventilation System.

This appliance is designed to vent

cooking smoke and odors only.

This appliance is intended for

residential use only. Use the

appliance only for its intended

purpose. The manufacturer cannot

be held responsible for damages

caused by improper use of the

hood.

Be certain your appliance is prop-

erly installed and grounded by a

qualified technician.

To guarantee the electrical safety of this

appliance, continuity must exist

between the appliance and an effective

grounding system. It is imperative that

this basic safety requirement be met. If

there is any doubt, have the electrical

system of the house checked by a

qualified electrician. The manufacturer

can not be held responsible for

damages caused by the lack, or

inadequacy of, an effective grounding

system.

This appliance complies with current

safety requirements. Improper use of

the appliance can lead to personal

injury and material damage.

READ AND SAVE THESE

INSTRUCTIONS

Before connecting the appliance to

the power supply make sure that

the voltage and frequency listed on the

data plate correspond with the house-

hold electrical supply. This data must

correspond to prevent machine

damage. Consult a qualified electrician

if in doubt.

CAUTION

For General Ventilating Use Only.

Do Not Use To Exhaust Hazardous

Or Explosive Materials And Vapors.

Installation work and repairs should

only be performed by a qualified

technician in accordance with all

applicable codes and standards.

Repairs and other work by unqualified

persons could be dangerous and the

manufacturer will not be held

responsible.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

This equipment is not designed for Use

maritime use or for use in mobile

Do not allow children to play with

installations such as caravans or air-

craft. However, under certain conditions

it may be possible for an installation in

these applications. Please contact the

nearest Miele dealer or the Miele Tech-

nical Service Department with specific

requirements.

or operate the appliance or its

controls. Supervise its use by the

elderly or infirm.

Be careful when preparing a

flambé beneath the hood.

Flames may be drawn up into the hood

by the suction or grease filters may

catch fire.

Before servicing or cleaning the

unit, switch power off at the service

panel and lock the service disconnect-

ing means to prevent power from being

switched on accidentally. When the

service disconnecting means can not

be locked, securely fasten a prominent

warning device, such as a tag, to the

service panel.

Never operate gas burners without

pots.

Do not leave cooking surfaces

unattended while in use. Over-

heated food, oil and grease can catch

fire.

Do not use the hood without the

grease filters in place.

Before discarding an old

appliance, unplug it from the

Clean the grease filters regularly.

Dirty filters are a fire hazard.

power supply and remove the power

cord and any doors to prevent hazards.

Do not use a steam cleaner to

clean the hood. Steam could

penetrate electrical components and

cause a short circuit.

In areas subject to infestation by

cockroaches or other pest, keep

the appliance and its surroundings

clean at all times. Any damage caused

by cockroaches or other pest will not

be covered under warranty.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

, WARNING - TO REDUCE

THE RISK OF A RANGE TOP

GREASE FIRE:

, WARNING

TO REDUCE THE RISK OF INJURY

TO PERSONS IN THE EVENT OF A

RANGE TOP GREASE FIRE,

OBSERVE THE FOLLOWING:

Never leave surface units unat-

tended at high settings. Boilovers

cause smoking and greasy spillovers

may ignite. Heat oils slowly on low or

medium settings.

SMOTHER FLAMES with a close

fitting lid, cookie sheet, or metal

tray, then turn off the burner.

BE CAREFUL TO PREVENT BURNS.

If the flames do not go out immediately,

EVACUATE AND CALL THE FIRE

DEPARTMENT.

Always turn hood "ON" when cook-

ing at high heat or when cooking

flaming foods.

Clean ventilating fans frequently.

Grease should not be allowed to

accumulate on fan or filter.

NEVER PICK UP A FLAMING

PAN - You may be burned.

DO NOT USE WATER, including

wet dishcloths or towels - a violent

steam explosion will result.

Use proper pan size. Always use

cookware appropriate for the size

of the surface element.

Use an extinguisher

ONLY IF:

– You know you have a Class ABC

extinguisher, and you already know

how to operate it.

– The fire is small and contained in the

area where it started.

– The fire department is being called.

– You can fight the fire with your back

to an exit.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Installation

Never connect an exhaust hood to

an active chimney, dryer vent, vent

flue, or room ventilating ductwork. Seek

professional advice before connecting

an exhaust hood vent to an existing,

, WARNING

To reduce the risk of fire, only

use metal ductwork.

When installing the hood, follow the inactive chimney or vent flue.

recommended minimum safety dis-

Ducted fans must always be

tances between a Miele cooktop and

vented outdoors.

the hood:

Make sure that the airflow in the

– 22" (55 cm) above electric cooktops,

room is sufficient for combustion

– 26" (65 cm) above gas cooktops,

– 26" (65 cm) above an open grill.

and exhausting of all non-electric heat-

ing appliances (water heaters, gas

cooktops, gas ovens, etc.), otherwise

backdrafts may occur. Follow the heat-

ing manufacturer’s guidelines and

safety standards or those published by

the National Fire Protection Association

(NFPA), or the American Society for

Heating, Refrigeration and Air

If local building codes require a greater

safety distance, follow their require-

ment.

For non-Miele cooking appliances

maintain the safety distances recom-

mended by the appliance manufacturer

in their installation and operating

instructions.

If there is more than one appliance

beneath the hood and they have differ-

ent minimum safety distances always

select the greater distance.

Conditioning Engineers (ASHRAE).

If in doubt, consult an experienced

professional.

Be careful not to damage hidden

electrical wiring or plumbing when

cutting or drilling into the wall or ceiling.

Do not use an extension cord to

connect the appliance to electricity.

Extension cords do not guarantee the

required safety of the appliance, (e.g.

danger of overheating).

Do not install this hood over

cooktops burning solid fuel.

Any fittings, sealant, or materials

used to install the ductwork must

be made of approved non-flammable

materials.

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the appliance

DA 210-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the appliance

DA 220-2

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the appliance

a Cover plate

h Light button

This button turns the light on and off

and also dims the light.

b Chimney

The lighting can be used independently

of the fan.

c Canopy

d Grease filters

e Overhead lighting

f Control panel

g Main power switch

i On/Off button

j Fan power level buttons

Four fan speed selection.

k Delayed Shut Down

This button activates the Delayed Shut

Down feature. The fan can be set to

turn off automatically after either 5 or 15

minutes.

l Grease filter button

The indicator above to the grease filter

button lights when the grease filters

need to be cleaned.

This button is also used:

– to reset the grease filter timer after

cleaning the grease filters (see

"Cleaning and Care").

– to show how long the grease filter

has been in use (see "Operation /

Grease filter timer").

– to change the number of hours

counted by the grease filter timer

(see "Operation / Reprogramming the

grease filter timer").

Download from Www.Somanuals.com. All Manuals Search And Download.

Functional description

The ventilation hood works by air ex-

traction. The air is drawn in and

cleaned by the grease filters and di-

rected outside.

The hood comes equipped with a

non-return flap. This flap automatically

closes when the hood is turned off so

that no exchange of outside air and

room air can occur. When the hood is

turned on, the air pressure of the ex-

haust fan automatically opens the flap

blowing the inside air and cooking

odors outside.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Main power switch

Intensive setting

Level "4" (yellow indicator) should be

used for a short period when frying or

cooking food with a strong aroma.

Fan performance

Press the main power switch to "I". The

fan and the lighting can now be oper-

ated.

The maximum air flow capacity is

625 cfm. Factors such as narrow duct

diameter and bends will affect this

value.

If the appliance is not going to be used

for a long period of time (e.g. while va-

cationing) turn the appliance off by

pressing the main power switch to "0".

Level 1 operates at 40% capacity

Level 2 operates at 60% capacity

Level 3 operates at 80% capacity

Level 4 operates at 100% capacity

The next time it is turned on, the hood

will operate at the level previously used.

Delayed Shut Down

Turning on the fan

If odors or smoke remain in the kitchen

after cooking has been completed, the

Delayed Shut Down feature can be se-

lected to allow the hood to continue

running for either 5 or 15 minutes.

^ Press the On/Off button.

The fan runs at power level "2".

The On/Off indicator lights.

Selecting the power level

^ Press the Delayed Shut Down button

while the fan is still running.

Press once = 5 minute delay

(left indicator lights)

Press twice = 15 minute delay

(right indicator lights)

^ Use the _ buttons to select the

desired power level.

To cancel the Delayed Shut Down fea-

ture press the button again.

& =increases the fan speed

$ =decreases the fan speed

Level "1" to "3" (green indicators) are

usually sufficient for normal cooking.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Turning off the fan

Turning the lighting on/off

The overhead lighting can be turned on

and off independently of the fan.

^ Press the On/Off button to turn the

fan off.

The indicator goes out.

^ Press the light button briefly to turn

on the lighting.

Automatic Safety Shut Off

The light button indicator illuminates.

The fan will turn off automatically

10 hours after the last button was acti-

vated. The lighting however will remain

on.

^ Press the light button briefly again to

turn off the lighting.

The light button indicator will go out.

^ Press the On/Off button to turn the

fan back on again.

Dimming the lighting

The brightness of the lighting can be

adjusted.

^ While the lighting is turned on, press

the light button.

The lighting will dim until the button is

released.

^ If the button is pressed again, the

lighting will brighten until the button is

released.

If the button is pressed continuously,

the light will cycle between bright and

dark.

^ Press the light button again to turn off

the lighting.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Grease filter timer

Checking the grease filter timer

A timer monitors the hours of fan opera- To check the percentage of time al-

tion. The indicator for the grease filter

will light after 30 hours of operation. The

grease filters must then be cleaned.

ready used:

After the grease filters have been

cleaned and put in place, the grease fil-

ter timer must be reset.

^ Press the On/Off button to turn the

fan on.

^ To do this, press the grease filter but-

ton for about 3 seconds.

^ Press the grease filter button.

The indicator will go out.

The number of flashing _ indicators

show the percentage of programmed

hours that have been used.

1 indicator = less than 25 %

2 indicators = less than 50 %

3 indicators = less than 75 %

4 indicators = less than 100 %

This information will remain stored in

memory in the event of a power failure.

Download from Www.Somanuals.com. All Manuals Search And Download.

Operation

Reprogramming the grease filter

timer

The grease filter timer is preset to 30

hours. This time can be lengthened or

shortened to 20, 30, 40 or 50 hours.

The indicator for the grease filter and

one of the _ indicators will flash.

– A time of 20 hours should be pro-

grammed in kitchens with frequent

pan or deep frying.

The lit _ indicator shows the pro-

grammed time:

1st indicator from the left = 20 hours

2nd indicator from the left = 30 hours

3rd indicator from the left = 40 hours

4th indicator from the left = 50 hours.

– A time of 20 hours should also be

programmed if the kitchen is only

used occasionally. Otherwise grease

which has accumulated over a long

period of time will harden on the fil-

ters making cleaning more difficult.

^ Use the $ or & button to select the

desired time.

^ Press the On/Off button to turn off the

fan.

^ Store the selection by pressing the

grease filter button.

If the procedure is not stored within

4 minutes of programming, the hood

will automatically default to the "old"

data.

^ Press the Delayed Shut Down and

grease filter buttons at the same time.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Stainless steel

Before cleaning or servicing the

hood, disconnect it from the power

supply by either removing the fuse,

unplugging it from the outlet or man-

ually "tripping" the circuit breaker.

Stainless steel surfaces can be cleaned

using a non-abrasive stainless steel

cleaner.

To help prevent resoiling, a conditioner

for stainless steel can also be used.

Apply sparingly with even pressure.

Cleaning the casing

,^{Never use abrasive cleaners,}

scouring pads, steel wool or caustic

(oven) cleaners on the hood. They

will damage the surface.

Stainless steel colored controls

These controls may become discol-

ored or damaged if not cleaned reg-

ularly.

Do not use a stainless steel cleaner

on these controls.

^ All external surfaces and controls can

be cleaned with warm water and liq-

uid dish soap applied with a soft

sponge.

^ Wipe dry using a soft cloth.

Do not use too much water when

cleaning the controls. Water could

penetrate into the electronics and

cause damage.

^ Glass surfaces can be cleaned using

glass cleaner.

Avoid:

– cleaning agents containing soda, ac-

ids or chlorides,

– abrasive cleaning agents e.g. pow-

der or cream cleansers,

– abrasive sponges, e.g. pot scourers

or sponges which have been previ-

ously used with abrasive cleaning

agents.

These will damage the surface.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Grease filters

^ Clean the filters

- by hand: use a scrub brush in

warm water with a mild detergent.

- in a dishwasher: place the filters in

the lower basket, making sure that

the spray arm is not blocked.

The reusable metal grease filters re-

move solid particles from the vented

kitchen air (grease, dust, etc).

Depending on the detergent, clean-

ing the grease filters in a dishwasher

may cause permanent discoloration

of the filter surface. Performance of

the filter will not be affected by this

discoloration.

The grease filters should be cleaned

every 3-4 weeks or whenever the

grease filter timer indicator lights.

A dirty filter is a fire hazard.

^ After cleaning, the filters can be

placed on a towel to air dry.

^ While the filters are removed, clean

any dirt or grease from the filter cas-

ing to prevent the risk of fire.

When putting the grease filters back

make sure that the locking clips are vis-

ible facing down towards the cooking

surface.

If the filters are incorrectly installed, in-

sert a small screwdriver into the slit

along its edge to disengage it from the

casing.

^ After returning the grease filters,

press the grease filter button for

3 seconds to reset the timer. The indi-

cator light will go out.

^ To remove the grease filters press the

locking clips in towards the middle of

the filter. Holding carefully, lower and

remove the filter.

^ If the grease filters are cleaned be-

fore the timer has reached its maxi-

mum, the grease filter button should

be pressed for 6 seconds to reset the

counter to zero.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Changing the light bulb

To change a bulb:

Before changing the light bulbs, dis-

connect the hood from the power

supply by either removing the fuse,

unplugging it, or manually "tripping"

the circuit breaker.

When in use halogen bulbs become

extremely hot, and they can burn

your hands. Do not attempt to

change the bulbs until they have

had sufficient time to cool down.

^ Remove the outer ring, a.

Do not touch the bulb surface. Fin-

gerprints or body oils deposited on

the bulb will decrease the life of the

bulb. Please follow the bulb manu-

facturer’s instructions.

^ Support the glass, c, while detach-

ing the circlip, b. Be careful not to let

the glass fall out.

^ Pull the old bulb, d, out of its socket

and replace it with a new one.

^ Reinstall the glass, circlip and outer

ring.

Never use the lights without the

glass, c, installed. The glass is spe-

cially made to filter harmful light

rays.

Download from Www.Somanuals.com. All Manuals Search And Download.

After Sales Service

In the event of a fault which you cannot

correct yourself please contact:

– Your Miele Dealer

– The Miele Technical Service

Department

USA 1-800-999-1360

[email protected]

CDN 1-800-565-6435

[email protected]

When contacting the Technical Service

Department, please quote the model

and serial number of your appliance.

These are shown on the data plate

which is visible when the grease filter is

removed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation instructions

Download from Www.Somanuals.com. All Manuals Search And Download.

Table of Contents

Caring for the environment

Structural support

Electrical data

Appliance dimensions

DA 210-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

DA 220-2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Installation

Air extraction

Download from Www.Somanuals.com. All Manuals Search And Download.

Caring for the environment

Disposal of packing material

Disposal of an old appliance

The cardboard box and packing

materials protect the appliance during

shipping. They have been designed to

be biodegradable and recyclable.

Please recycle.

Old appliances may contain materials

that can be recycled. Please contact

your local recycling authority about the

possibility of recycling these materials.

Before discarding an old hood, un-

plug it from the outlet and cut off its

power cord to prevent hazards.

Ensure that any plastic wrappings,

bags etc. are disposed of safely and

kept out of the reach of children.

Danger of suffocation!

Download from Www.Somanuals.com. All Manuals Search And Download.

Structural support

The ceiling mounting plate will sup-

port the weight of the hood. This

ceiling plate must be attached to

rigid structural framing that is sup-

ported in its entirety by the ceiling

joists, or to the ceiling joists directly.

Do not attach the plate directly to the

ceiling by using anchors, mollies or

toggle bolts.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical data

Important

All electrical work should be per-

formed by a qualified electrician in

strict accordance with national and

local safety regulations.

Installation, repairs and other work

by unqualified persons could be

dangerous. The manufacturer can

not be held responsible for unautho-

rized work.

The hood must be hard wired accord-

ingly:

Black/Red wire:. . . . connect to L1 (live)

White wire: . . . . . connect to N (neutral)

Green wire: . . connect to GND (ground)

Ensure that power to the appliance

is OFF while installation or repair

work is performed.

Maximum load

DA 210-2, 220-2 . . . . . . . . . . . . . 430 W

Lighting . . . . . . . . . . . . . . . . . . 4 x 20 W

Voltage . . . . . . . . . . . . . . . . . . . . . 120 V

Frequency . . . . . . . . . . . . . . . . . . 60 Hz

Circuit rating. . . . . . . . . . . . . . . . . . 15 A

Verify that the voltage, load and circuit

rating information found on the data

plate (located behind the grease fil-

ters), match the household electrical

supply before installing the hood.

If there is any question concerning the

electrical connection of this appliance

to your power supply, please consult a

licensed electrician or call Miele’s Tech-

nical Service Department.

USA 1-800-999-1360

CDN 1-800-565-6435

WARNING:

THIS APPLIANCE MUST BE

GROUNDED

Download from Www.Somanuals.com. All Manuals Search And Download.

Appliance dimensions

DA 210-2

a Mounting bolt holes

b Alternative positions for feeding through the power cord

c Exhaust connection 6" (150 mm) diameter

Download from Www.Somanuals.com. All Manuals Search And Download.

Appliance dimensions

DA 220-2

a Mounting bolt holes

b Alternative positions for feeding through the power cord

c Exhaust connection 6" (150 mm) diameter

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

Do not install this exhaust hood over

cooktops burning solid fuel.

When installing the hood, make sure

that the following minimum dis-

tance (S) between the top of a Miele

cooking surface and the bottom of

the hood is:

- 22" (55 cm) above electric cooktops

- 26" (65 cm) above gas cooktops

- 26" (65 cm) above an open grill

For non-Miele cooking appliances

maintain the safety distances recom-

mended by the cooktop manufac-

turer in their installation and operat-

ing instructions.

If there is more than one appliance

beneath the hood and they have dif-

ferent minimum safety distances al-

ways select the greater distance.

^ Make a line on the ceiling going from

the rear of the cooktop towards the

front and centered over the cooktop.

^ Cut a 7 ¹/₂" (190 mm) hole in the ceil-

ing for the exhaust duct to pass

through. The exhaust connection has

a 6" (150 mm) diameter.

See "Warning and Safety instruc-

tions" for further information.

26" (65 cm) is recommended for all in-

stallations to allow for optimum work

space under the hood.

CAUTION:

During the installation process,

please be careful of sharp edges

that can cause harm.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

^ Feed the ductwork and power cable

through their respective holes in the

ceiling.

If 6" (150 mm) ductwork is not possible

then 5" (125 mm) ductwork can be

used in conjunction with a reducing

collar available from the Miele Technical

Service Department (see "Installation /

Air extraction" for further details).

Mounting plate: DA 210-2

^ Drill four ³/₁₆" (5 mm) holes in the ceil-

ing.

Mounting plate: DA 220-2

The S10 wall anchors included in the

packaging are not for use in

USA/CDN. Be certain that the ceiling

is stable enough to support the

hood.

^ Hold the mounting plate up to the

ceiling so that the orange arrow faces

the front of the hood and aligns with

the line drawn on the ceilling.

Mark the position of the four mount-

ing bolts a for securing the mounting

plate and determining the position of

the hole the power cord b will pass

through.

Select the hole providing the shortest

route for the power cable b to reach

the power terminal located at the top

of the hood’s chimney.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

^ Secure the ducting to the mounting

plate using a hose clip.

^ Insert the short edge of the two

spring clips into their slots from be-

low and pivot them 90° so that the

tab faces the center of the mounting

brake.

^ Pull the power cord through the

mounting plate.

^ Insert the four countersunk screws

M 6 x 20 into the recessed holes from

above.

^ Tape the screws from above to pre-

vent them from being pushed up-

wards when the nuts are tightened.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

^ Screw the mounting plate through the

ceiling and into the structural framing

using 8 x 60 lag bolts and washers.

Once tight, make sure that the

mounting plate can safely support

the weight of the hood.

^ Using at least two people, lift the

hood and guide the spring clips

through their respective slots in the

flange at the top of the chimney.

Make sure they click into place and that

the hood is hanging securely from the

spring clips before allowing them to

carry the weight.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation

^ Bolt the flange firmly to the ceiling us-

ing the four M6 nuts.

^ Finally, being careful not to scratch

the chimney, push the cover plate up-

wards until the spring fixing clips

click into place. If installed correctly,

the cover should be secure and flush

against the ceiling.

^ Shorten the power cable as much as

possible and attach it to the terminal

block inside the chimney. See "Elec-

trical data".

Before connecting the appliance

read the "Warning and Safety In-

structions" and "Electrical data" sec-

tions.

^ Before using the appliance remove

the grease filter and remove the pro-

tective foil from the filter frame. Re-

turn filter.

Download from Www.Somanuals.com. All Manuals Search And Download.

Air extraction

– Use smooth or flexible pipes made

from approved non-flammable mate-

rials for exhaust ducting.

Danger of toxic fumes.

Gas cooking appliances release

carbon monoxide that can be harm-

ful or fatal if inhaled. The exhaust

gases extracted by the hood

should be vented outside of the

building only.

Do not terminate the exhaust

ducts in attics, garages,

crawlspaces, etc.

– Where the ductwork is horizontal, it

must slope away from the hood at

least ¹/₈" per foot (1cm per meter) to

prevent condensation dripping into

the appliance.

– If the exhaust is ducted through an

outside wall, a Miele Telescopic Wall

Vent can be used.

Please read and follow the "Warning

and Safety Instructions" to reduce the

risk of personal injury. Follow all local

building codes when installing the

hood.

Exhaust ducting and connections

– The ducting should be as short and

straight as possible, and the number

of sharp bends should be minimized.

– For most efficient air extraction, the

diameter of the ductwork should not

be less than 6" (150 mm). Use of flat

ducts also reduces the air extraction

efficiency.

– Noise levels of the hood will increase

if flat ducts or round ducts of less

than 6" (150 mm) in diameter are

used.

– If the exhaust is ducted into an inac-

tive flue, the air must be expelled

parallel to the flow direction of the

flue.

WARNING

To reduce the risk of fire, only use

metal ductwork.

CAUTION

To reduce risk of fire and to properly

exhaust air, be sure to duct air out-

side. Do not vent exhaust air into

spaces within walls or ceilings or

into attics, crawl spaces, or garages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Air extraction

Never connect an exhaust hood to

an active chimney, dryer vent, vent

flue, or room venting ductwork. Seek

professional advice before connect-

ing an exhaust hood vent to an exist-

ing, inactive chimney or vent flue.

Ductwork with a diameter of less

than 6" (150 mm) should only be

used when absolutely necessary. As

duct diameter decreases, the hood’s

performance and sound levels will

be affected.

Important:

If the ductwork runs through rooms,

ceilings, garages, etc. where tempera-

ture variations exist, it may need to be

insulated to reduce condensation. In

some cases, a condensate trap may

also be required to collect and evapo-

rate any condensate which may occur.

When installing a condensate trap,

ensure that it is positioned vertically

and if possible directly above the ex-

haust outlet.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alteration rights reserved / 5002

M.-Nr. 05 853 490 / V00

This paper is made from cellulose bleached without the use of chlorine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Murray Lawn Mower 22 Front Drive User Manual
NEC Home Theater System NP M260WJL User Manual
NordicTrack Treadmill NTTL24080 User Manual
Oceanic Personal Computer Veo 100Nx User Manual
Olivetti Copier 120D User Manual
Onkyo Home Theater System PHC 5 User Manual
Oregon Scientific Marine Radio WMR86 User Manual
Palm Cell Phone PTR690HKP User Manual
Panasonic Cordless Telephone KX TG2521E User Manual
Parkinson Cowan Cooktop Renown GR User Manual