Operating and Installation
Instructions
Ventilation System
DA 6590 D
en - US
To prevent accidents
and appliance damage,
read these instructions
before
installation or use.
M.-Nr. 09 523 580
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
,WARNING
READ AND SAVE THESE
INSTRUCTIONS
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
Keep these instructions in a safe
place and pass them on to any future
user.
OBSERVE THE FOLLOWING:
a) Use this appliance only in the
~
manner intended by the manufacturer.
If you have questions, contact Miele.
Read these instructions carefully
before installing or using the
Ventilation System.
b) Before servicing or cleaning the
~
appliance, switch power off at the
service panel and lock the service
disconnecting means to prevent power
from being switched on accidentally. If
the service disconnecting means
cannot be locked, securely fasten a
prominent warning device, such as a
tag, to the service panel.
This appliance is intended for
residential use only. Use the appliance
only for its intended purpose.
~
This appliance complies with current
~
safety requirements. Improper use of
the appliance can lead to personal
injury and material damage.
c) Be certain your appliance is
properly installed and grounded by a
qualified technician.
~
,CAUTION
For General Ventilating Use
Only. Do Not Use To Exhaust
Hazardous Or Explosive
Materials And Vapors.
To guarantee the electrical safety of this
appliance, continuity must exist
between the appliance and an effective
grounding system. It is imperative that
this basic safety requirement be met. If
there is any doubt, have the electrical
system of the house checked by a
qualified electrician.
This appliance is designed to vent
~
cooking smoke and odors only.
This appliance is suitable for
~
installation above gas or electric
cooking surfaces.
This appliance is not intended for
outdoor use.
~
This appliance must not be used in
~
a non-stationary location (e.g. on a
ship).
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
d) Before connecting the appliance
Use
~
to the power supply make sure that the
voltage and frequency listed on the
data plate correspond with the
household electrical supply.
This data must correspond to prevent
appliance damage. If in doubt consult a
qualified electrician.
,WARNING
TO REDUCE THE RISK OF A
COOKTOP GREASE FIRE:
a) Never leave surface units
~
unattended at high settings. Boilovers
cause smoking and greasy spillovers
may ignite. Heat oils slowly on low or
medium settings.
e) Installation work and repairs
~
should only be performed by a qualified
technician in accordance with all
applicable codes and standards.
Repairs and other work by unqualified
persons could be dangerous.
b) Always turn the hood on when
~
cooking at a high heat.
c) Clean the ventilation hood
~
f) Only open the housing as
frequently. Grease should not be
allowed to accumulate on the fan or
filter.
~
described in the enclosed "Installation
diagram" and in the "Cleaning and care"
section of this manual. Under no
circumstances should any other parts
of the housing be opened. Tampering
with electrical connections or
d) Use the proper pan size. Always
~
use cookware appropriate for the size
of the cooking area.
components and mechanical parts is
highly dangerous to the user and can
cause operation faults.
e) Do not flambé or grill with an
~
open flame beneath the hood.
Flames could be drawn up into the
hood by the suction and the grease
filters may catch fire.
g) Before discarding an old
~
appliance, disconnect it from the power
supply and remove the power cord to
prevent hazards.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
,WARNING
Do not allow children to play with or
operate the appliance or its controls.
Supervise its use by the elderly or
infirm.
~
TO REDUCE THE RISK OF
INJURY TO PERSONS IN THE
EVENT OF A COOKTOP
GREASE FIRE, OBSERVE THE
FOLLOWING*:
Always turn on the hood when using
~
the cooktop to prevent damage from
condensation.
a) SMOTHER FLAMES with a close
fitting lid, cookie sheet, or metal tray
then turn off the burner.
BE CAREFUL TO PREVENT BURNS.
If the flames do not go out immediately,
EVACUATE AND CALL THE FIRE
DEPARTMENT.
~
Never operate gas burners without
~
cookware. Turn the burner off when not
in use. Adjust the burner so that the
flames do not extend beneath the
cookware. Do not overheat the
cookware, e.g. when using a wok. The
hood can be damaged due to
excessive heat from the burners and
the cookware.
b) NEVER PICK UP A FLAMING
~
PAN - You may be burned.
c) DO NOT USE WATER, including
wet dishcloths or towels - a violent
steam explosion will result.
Do not use the hood without the
grease filters in place.
~
~
Do not use a steam cleaner to clean
~
d) Use a fire extinguisher ONLY if:
the hood. Steam could penetrate
electrical components and cause a
short circuit.
~
1) You have a class ABC
extinguisher, and you know how to
operate it.
2) The fire is small and contained in
the area where it started.
3) The fire department is being
called.
4)You can fight the fire with your
back to an exit.
*
Based on "Kitchen Firesafety Tips"
published by NAFTA
5
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Installation
g) Do not install this hood over
~
cooktops that burn solid fuel.
,WARNING
h) Provided a larger distance is not
~
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
given by the manufacturer of the
cooktop, follow the minimum safety
distances between a cooktop and the
bottom of the hood given in the
"Appliance dimensions" section of this
manual.
a) Installation work and electrical
~
wiring must be done by qualified
person(s) in accordance with all
applicable codes and standards,
including fire-rated construction.
If local building codes require a greater
safety distance, follow their
requirement.
If there is more than one appliance
beneath the hood and they have
different minimum safety distances
always select the greater distance.
b) Sufficient air is needed for
~
combustion and exhausting of gases
through the flue (chimney of fuel
burning equipment to prevent back
drafting. Follow the heating equipment
manufacturer’s guideline and safety
standards such as those published by
the National Fire Protection Association
(NFPA) and the American Society for
Heating, Refrigeration and Air
i) Never connect an exhaust hood to
~
an active chimney, dryer vent, vent flue,
or room ventilating ductwork.
j) Seek professional advice before
~
connecting an exhaust hood vent to an
existing, inactive chimney or vent flue.
Conditioning Engineers (ASHRAE), and
the local code authorities.
k) Any fittings, sealant, or materials
~
used to install the ductwork must be
made of approved non-flammable
materials.
c) When cutting or drilling into the
wall or ceiling, do not damage electrical
wiring and other hidden utilities.
~
d) Ducted hoods must always be
vented to the outdoors.
~
,WARNING
TO REDUCE THE RISK OF
FIRE USE ONLY METAL
DUCTWORK.
e) Do not use this hood with any
~
solid-state speed control device.
f) Do not use an extension cord to
~
connect the appliance to electricity.
Extension cords do not guarantee the
required safety of the appliance,
(e.g. danger of overheating).
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of functions
Air extraction
The air is drawn in via the glass or
stainless steel panels and cleaned by
the grease filters. Then the air is
released outdoors.
The hood comes equipped with a
non-return flap. This flap automatically
closes when the hood is turned off so
that no exchange of outside air and
room air can occur. When the hood is
turned on, the air pressure of the
exhaust fan automatically opens the
flap blowing the inside air and cooking
odors outside.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the ventilation system
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the ventilation system
aChimney extension
bChimney
lFilter button
The grease filter symbol l of the filter
button comes on when the grease
filters need to be cleaned.
cCanopy
dControl panel
The — symbol has no function with this
model.
eOverhead lighting
fGrease filter
Use this button to reset the grease filter
timer after cleaning the grease filters
(see "Cleaning and care").
gGlass or stainless steel panels
Optional accessories
You can also check or change the
number of hours.
DRP 6590 D glass (3 elements)
DRP 6590 D stainless steel
(3 elements)
hOverhead lighting button
This button turns the light on and off
and also dims it.
iFan On/Off button
jFan power selection
kDelayed shut down
This button activates the Delayed Shut
Down feature. The fan can be set to
turn off automatically after either 5 or 15
minutes.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Turning the fan on K
Automatically switching back the
intensive power level
^ Press the On/Off button K.
The intensive level can be programmed
to automatically switch back to level 3
after 10 minutes.
The fan turns on to Level 2
and the K symbol and the 2 of the
power level indicator lights up.
^ To do so, turn the fan and the
overhead lighting off.
Selecting the power level - / +
^ Press and hold the "Delayed shut
down" button 5 ¢15 for approx. 10
seconds until power level indicator 1
lights up.
^ Press the "–" symbol to select a lower
power level or the "+" symbol for a
higher power level.
Depending on the amount of cooking
odors, levels 1 to 3 are usually sufficient
for normal cooking.
^ Then press the following buttons one
after another:
– overhead lighting I,
Intensive setting "IS"
– the – button and
To remove strong aromas or odors, for
example when frying, select power
level IS temporarily.
– the overhead light button I again.
If the indicators 1 and IS flash,
automatic switch back is not activated.
^ To activate automatic switch back,
press the + button.
Power level indicators 1 and IS come
on.
To deactivate, press the – button.
^ To save the setting, press the
delayed shut down button 5 ¢15.
If the procedure is not stored within 4
minutes, the hood will automatically
default to the "old" data.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Delayed shut down 5¢15
Overhead lighting I
For both air extraction and recirculation
it is recommended to run the fan for
several minutes after cooking is
completed.
Turning the overhead lighting on
The overhead lighting can be turned on
and off independently of the fan.
This helps clear the kitchen air of any
remaining vapors and odors.
^ Press the light button I briefly to
turn the light on.
The delayed shut down feature can be
selected to turn the fan off automatically
after a preselected length of time.
The I indicator comes on.
The overhead light comes on at
maximum brightness.
^ After cooking, and with the fan on,
press the delayed shut down button
5 ¢15:
Dimming the overhead light
The brightness of the light can be
adjusted.
– once: The fan automatically turns off
after 5 minutes (5 ¢ comes on).
^ While the light is turned on, press
and hold the light button I.
The light dims until the button is
released.
– twice: The fan automatically turns off
after 15 minutes (¢15 comes on).
If you press the delayed shut down
button 5 ¢15 again, the fan will not turn
off automatically (5 ¢15 goes out).
^ If the button I is pressed and held
down again, the light brightens until
the button is released.
Turning the fan off K
If the I button is pressed continuously,
the light cycles between light and dark.
^ Press the On/Off button K to turn the
fan off
Turning the overhead light off
The K indicator goes out.
^ Briefly press the light button I to
turn the light off.
The I indicator goes out.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Automatic safety shut-off
The factory setting for the grease filter
timer is 30 hours. You can adjust the
time to 20, 30, 40 or 50 hours.
The fan will turn automatically off 10
hours of use. The lighting however will
remain on.
^ Press the On/Off button K to turn the
fan off.
^ Press the On/Off button K to turn the
fan back on again.
^ Press the delayed shut down button
5 ¢15 and the timer button [— at
the same time.
Filter timer [—
The grease filter symbol [ of the timer
button and one of the power level
indicators flash.
A timer counts the hours of fan
operation.
The filter button signals that the grease
filter needs to be cleaned by turning on
the grease filter symbol [.
The 1 to IS indicators show the
programmed time:
Indicator 1 . . . . . . . . . . . . . . . . 20 hours
Indicator 2 . . . . . . . . . . . . . . . . 30 hours
Indicator 3 . . . . . . . . . . . . . . . . 40 hours
Indicator IS . . . . . . . . . . . . . . . 50 hours.
See "Cleaning and care" for information
on cleaning and replacing filters and
resetting the timers.
^ Press – to select a shorter operating
time or + for a longer one.
Reprogramming the filter timer [
The timer may be set to suit your
cooking habits.
^ Save the setting by pressing the
timer button [—.
– If you often roast and fry foods,
choose a shorter operating time.
All the lights go out.
If the procedure is not stored within 4
minutes, the hood will automatically
default to the "old" data.
– If you tend to cook fat-free, choose a
longer operating time.
– If you cook only occasionally, it is
better to choose a shorter operating
time. This is because grease
deposits harden over time, making
cleaning difficult.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Checking the elapsed operating time
Even before the maximum operating
time has been reached, you can check
what percentage of the time has
elapsed.
^ Press the On/Off button K to turn the
fan on.
^ Press the timer button [— –
– once, to check the grease filter
operating time. The grease filter
symbol [ comes on.
At the same time one or more power
level indicators start flashing.
The number of flashing indicators
shows the elapsed operating time:
Indicator 1 . . . . . . . . . . . . . . . . . . . 25%
Indicators 1 and 2 . . . . . . . . . . . . . 50%
Indicators 1 to 3 . . . . . . . . . . . . . . . 75%
Indicators 1 to IS . . . . . . . . . . . . . 100%
The number of operating hours remains
stored when the ventilation system is
turned off or if the electric power supply
is interrupted.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
,WARNING
Avoid:
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
– cleaning agents containing soda,
acids or chlorides,
– abrasive cleaning agents
e.g. powder or cream cleansers,
– abrasive sponges, e.g. pot scourers
or sponges which have been
previously used with abrasive
cleaning agents.
Before cleaning or servicing the
hood, disconnect it from the power
supply, see "Important Safety
Instructions".
– sharp metal scrapers,
– oven spray.
,The halogen bulbs are very hot
when in use. They stay hot for some
time after turned off. Use caution,
danger of burns.
Wet cleaning the hot bulbs will
cause damage.
The following instructions for cleaning
"Stainless steel" surfaces and "Stainless
steel colored controls" should be
followed in addition to the general
"Cleaning the casing" instructions.
Wait a few minutes after turning
them off before cleaning.
Special instructions for appliances
with stainless steel surfaces
Cleaning the casing
(not applicable to the controls)
Never use abrasive cleaners,
scouring pads, steel wool or caustic
(oven) cleaners on the hood. They
will damage the surface.
Stainless steel surfaces can be cleaned
using a non-abrasive stainless steel
cleaner.
To help prevent resoiling, a conditioner
for stainless steel can be applied.
^ All external surfaces and controls can
be cleaned with a mild solution of
warm water and liquid dish soap
applied with a soft sponge.
Do not use too much water when
cleaning the controls. Water could
penetrate the electronics and cause
damage.
^ Wipe dry using a soft cloth.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Special instructions for glass
surfaces
Panels and grease filters
The glass or stainless steel panels and
the reusable metal grease filters
remove solid particles from the vented
kitchen air (grease, dust, etc.) and
prevent soiling of the ventilation hood.
^ The glass edge can be cleaned
using a household glass cleaner.
Special instructions for appliances
with colored casings
Clean the panels and grease filters at
the latest when the grease filter symbol
[ of the timer button comes on.
(Special order)
It is very difficult to clean this type of
surface without causing minor marks to
the surface material. This can become
particularly noticeable with darker
colors and if there is halogen lighting in
the kitchen.
The grease filters should be cleaned
every 3 - 4 weeks, as the collected
grease hardens over time and makes
cleaning more difficult.
,A dirty filter is a fire hazard!
Special instructions for control
buttons
Support the grease filters and
panels so that they do not fall and
damage the cooktop.
These controls may become dis-
colored or damaged if not cleaned
regularly.
Do not use a stainless steel cleaner
on these controls.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the grease filters
^ By hand: use a scrub brush with a
solution of warm water and mild dish
soap.
Do not use the pure detergent,
aggressive all purpose cleaners,
oven sprays, abrasive cleaning
agents or limescale removers. They
could damage the filter.
^ Pull the front edge of the panels
down slightly, unhook them at the
back, and take them out.
^ In a dishwasher: place the filter
vertically in the lower basket, making
sure that the spray arm is not
blocked.
Use a wash program with a max.
temperature of 150°F (65°C). In a
Miele dishwasher use the "Normal"
program.
Use the recommended amount of
dishwasher detergent. Overuse could
destroy the filter.
^ Open the grease filter lock, lower the
grease filter slightly, unhook it at the
back, and remove.
Depending on the detergent,
cleaning the grease filters in a
dishwasher may cause permanent
discoloration of the filter surface.
Filter performance will not be
affected by this discoloration.
Cleaning the panels by hand
^ Follow the instructions under
"Cleaning the casing".
^ After cleaning, place the filters on a
towel to air dry.
^ While the panels and the filters are
removed, clean any dirt or grease
from the casing. This reduces the risk
of fire.
^ When reinstalling the grease filters,
make sure that the locking clips are
facing down.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Resetting the grease filter timer
Reset the timer each time you clean the
grease filters.
^ With the fan running, press and hold
the timer button [— for
about 3 seconds, until only the 1 is
flashing.
The grease filter symbol [ goes out.
^ If the filters are incorrectly installed,
insert a small screwdriver into the slit
along its edge to disengage them
from the casing.
If you clean the grease filters before
the operating time elapses:
^ Press and hold the timer button [—
for about 6 seconds, until only the 1
is flashing.
^ Hook the panels onto the support
ledge, lift up the front and push them
into the lock until they engage.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Changing the light bulbs
,WARNING
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
Before changing the light bulbs,
disconnect the hood from the power
supply, see "Important Safety
Instructions".
When in use halogen bulbs become
extremely hot, and can burn your
hands. Do not attempt to change the
bulbs until they have had sufficient
time to cool.
^ To change the halogen bulb, first
gently press the light cover. The
cover will open and can now be
flipped down.
^ Pull the halogen bulb from its socket.
^ Using a cloth or glove, insert the new
halogen bulb (type 12 V, 20 W, G4).
Please follow the manufacturer's
instructions.
^ Flip the light cover back up, making
sure it clicks into place.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
After Sales Service
Repairs
MieleCare
In the event of a fault which you cannot
easily fix yourself, please contact the
Miele Technical Service Department.
(USA only)
MieleCare, our Extended Service
Contract program, gives you the
assurance of knowing that your
^ When contacting the Technical
Service Department, please quote
the model and serial number of your
appliance.
appliance investment is covered by
5 years of worry free ownership.
MieleCare is the only Extended Service
Contract in the industry that guarantees
repairs by a Miele Authorized Service
Provider using genuine Miele parts.
Only genuine Miele parts installed by
factory trained professionals can
guarantee the safety, reliability, and
longevity of your Miele appliance.
These are shown on the data plate
which is visible when the grease filters
are removed.
Please note that unless expressly
approved in writing by Miele’s Service
department, Extended Service
Contracts offered by other providers for
Miele products will not be recognized
by Miele. Our goal is to prevent
unauthorized (and untrained) service
personnel from working on your Miele
products, possibly doing further
damage to them, you and/or your
home.
To learn more about MieleCare
Extended Service Contracts, please
contact your appliance dealer or visit
us online at:
19
Download from Www.Somanuals.com. All Manuals Search And Download.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation Instructions
Read these instructions and the "Important Safety Instructions" before installing
this ventilation system.
The installation steps are described in the enclosed "Installation Diagram".
Leave these instructions with the appliance for the consumer/user.
Information is subject to change. Please refer to our website to obtain the most
current product specification, technical & warranty information.
Download from Www.Somanuals.com. All Manuals Search And Download.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of packing material
Disposal of an old appliance
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Please recycle.
Old appliances may contain materials
that can be recycled. Please contact
your local recycling center about the
possibility of recycling these materials.
Before discarding an old appliance,
disconnect it from the electrical
supply and cut off the power cord to
prevent it from becoming a hazard.
,DANGER
Ensure that any plastic wrappings,
bags, etc., are disposed of safely
and kept out of the reach of babies
and young children. Danger of
suffocation!
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance dimensions
1) Opening for exhaust duct and power
cord
Exhaust connection C 6" (150 mm)
The exhaust connection in the ceiling
plate is not secured in the center. This
makes installation possible if the
connection in the ceiling is not centered
above the cooktop. A max. variance of
1 3/16" (30 mm) in any direction is
possible.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance dimensions
Distance between cooktop and hood (S)
Do not install this exhaust hood over cooktops burning solid fuel.
Provided a larger distance is not given by the manufacturer of the cooktop, follow
the minimum safety distances between a cooktop and the bottom of the hood:
Miele Cooktops
Non-Miele
Cooktops
Electric Cooktops
24" (610 mm)
26" (660 mm)
Electric Barbeques and Fryers
Multiburner Gas cooktops
< 43,000 BTU (12.6 KW)
and no burner > 15,000 BTU (4.5 KW)
26" (660 mm)
30" (760 mm)
Single burner (Wok) < 20,500 BTU (6 KW)
All other gas cooktops
26" (660 mm)
30" (760 mm)
30" (760 mm)
– If several gas surfaces are installed under the hood, the total output must be
considered when determining the minimum safety distance.
– Be sure to follow the minimum safety distances given by the gas cooktop
manufacturer to easily flammable materials e.g. upper cabinets.
– If local building codes require a greater safety distance, follow their requirement.
– If there is more than one appliance beneath the hood and they have different
minimum safety distances always select the greater distance.
See "Important Safety Instructions" for further information.Also see the "Important
Safety Instructions" section.
– To ensure free access to work under the ventilation hood, a distance of a
minimum of 26" (660 mm) above the electric cooktop is also recommended.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Structural support
The ceiling mounting plate will
support the weight of the hood. This
ceiling plate must be attached to
rigid structural framing that is
supported in its entirety by the
ceiling joists, or to the ceiling joists
directly. Do not attach the plate
directly to the ceiling with anchors,
toggle bolts, etc.
,CAUTION
When cutting or drilling into the wall
or ceiling, do not damage electrical
wiring and other hidden utilities.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Before installation read the
information in the "Appliance
Dimensions" and " Important Safety
Instruction" chapters.
4 levelling plates for correcting an
uneven ceiling.
Under certain conditions, there is a
danger of poisonous fumes by when
the ventilation system and a furnace
drawing interior air run at the same
time.
Installation instructions
The individual installation steps are
described in the included Installation
diagram.
1 vent collar for allowing a variable
position for the vent hole in the ceiling.
Installation materials
1 hose clamp for attaching the exhaust
duct to the vent collar.
4 screws 8 x 60 mm with
4 washers and
4 wall anchors S 10for securing the
ceiling plate to the ceiling
The screws and anchors are suitable
for mounting on concrete ceilings.
For other types of ceiling materials,
use appropriate materials.
Ensure that the ceiling can support
the load.
2 screws M4 x 8 mm for securing the
chimney.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Air extraction
Exhaust ducting and connections
,WARNING
Use smooth or flexible pipework made
from approved non-flammable
materials for exhaust ducting.
Danger of toxic fumes.
Gas cooking appliances release
carbon monoxide that can be
harmful or fatal if inhaled.
To reduce the risk of fire and to
properly exhaust air, the exhaust
gases extracted by the hood
should be vented outside of the
building only.
To achieve the most efficient air
extraction and quietest noise levels,
consider the following:
– The diameter of the ductwork should
not be less than 6" (150 mm).
– If flat ducting is used, the cross
section must not be smaller than the
cross section of the ventilation
exhaust.
Do not vent exhaust air into
spaces within walls or ceilings or
in attics, crawl spaces or garages.
– The ducting should be as short and
straight as possible.
– Use ductwork with a wide radius.
To reduce the risk of fire, only use
metal ductwork.
– The exhaust duct must not be bent
or compressed.
Please read and follow the
"IMPORTANT SAFETY
INSTRUCTIONS" to reduce the risk of
personal injury. Follow all local building
codes when installing the hood.
– Make sure all connections are
secure.
– Where the ductwork is horizontal, it
must slope away from the hood at
least 1/8" per foot (1 cm per meter) to
prevent condensation dripping into
the appliance.
– If the exhaust is ducted through an
outside wall, a Telescopic Wall Vent
can be used.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Air extraction
Condensate trap
optional accessory
– If the exhaust is ducted into an
inactive flue, the air must be expelled
parallel to the flow direction of the
flue.
Never connect an exhaust hood to
an active chimney, dryer vent, flue,
or room venting ductwork. Seek
professional advice before
connecting an exhaust hood vent to
an existing, inactive chimney or vent
flue.
In some cases, a condensate trap may
also be required to collect and
evaporate any condensate which may
occur. This optional accessory is
available for ducts 5" (125 mm) and 6"
(150 mm) in diameter.
Important
If the ductwork runs through rooms,
ceilings, garages, etc. where
temperature variations exist, it may
need to be insulated to reduce
condensation.
^ When installing a condensate trap,
ensure that it is positioned vertically
and if possible directly above the
exhaust outlet.
If the ventilation system is designed for
an external fan, the condensate trap is
integrated into the hood (series ...EXT
only).
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
,WARNING
Important
TO REDUCE THE RISK OF
FIRE, ELECTRIC SHOCK, OR
INJURY TO PERSONS,
OBSERVE THE FOLLOWING:
To increase security before the
machine is installed, it is
recommended to install a protective
switch (30 mA).
All electrical work should be
performed by a qualified electrician
in strict accordance with national
regulations (for USA: ANSI-NFPA 70)
and local safety regulations.
Installation, repairs and other work
by unqualified persons could be
dangerous.
Important
The hood must be hard wired
accordingly:
Black/Red wire: connect to L1 (live)
White wire: connect to N (neutral)
Green wire: connect to GND (ground)
Ensure that power to the appliance
is off while installation or repair work
is performed.
^ Verify that the voltage, load and
circuit rating information found on the
data plate (located behind the
grease filter), match the household
electrical supply before installing the
hood.
If there is any question concerning the
electrical connection of this appliance
to your power supply, please consult a
licensed electrician or call Miele’s
Technical Service Department. See
back cover for contact information.
WARNING:
THIS APPLIANCE MUST BE
GROUNDED
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Total connected load. . . . . . . . . . 430 W
– Fan motor . . . . . . . . . . . . . . . . . 350 W
– Overhead lighting . . . . . . . . . 4 x 20 W
Voltage . . . . . . . . . . . . . . . . . . . . 120 V
Frequency . . . . . . . . . . . . . . . . . . 60 Hz
Fuse rating . . . . . . . . . . . . . . . . . . . 15 A
Weight
DA 6590 D. . . . . . . . . . . . 73 lbs (33 kg)
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / 5012
M.-Nr. 09 523 580 / 01
INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST
CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.
Download from Www.Somanuals.com. All Manuals Search And Download.
|