Operating and Installation instructions
Rangehood
DA 428-4, DA 428-4 EXT
DA 429-4, DA 429-4 EXT
en - AU, NZ
To avoid the risk of accidents
or damage to the appliance,
it is essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 09 201 520
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
or machine
The transport and protective packing
Electrical and electronic appliances /
has been selected from materials which machines often contain materials
are environmentally friendly for disposal which, if handled or disposed of
and can normally be recycled.
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Therefore,
please do not dispose of your old
machine or appliance with your
household waste.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Rather than just throwing these
materials away, please ensure they are
offered for recycling.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The plug must be rendered useless
and the cable cut off directly behind the
appliance or the machine to prevent
misuse.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This appliance is not suitable for
~
outdoor use.
This appliance complies with all
relevant local and national safety
requirements. Inappropriate use
can, however, lead to personal injury
and damage to property.
Any other usage is at the owner's risk.
Miele cannot be held liable for damage
resulting from incorrect or improper use
or operation.
This appliance is not intended for
To avoid the risk of accidents and
damage to the appliance, please
read these instructions carefully
before using it for the first time. They
contain important information on the
safety, installation, use and
~
use by persons (including children)
with reduced physical, sensory or
mental capabilities, or lack of
experience or knowledge, unless they
have been given supervision or
instruction concerning its use by a
person responsible for their safety.
maintenance of the appliance.
Keep these instructions in a safe
place and ensure that all users are
familiar with the contents. Pass them
on to any future owner of the
appliance.
Safety with children
This appliance is only intended for
~
use by adults who have read these
instructions. This appliance is not a toy!
To avoid the risk of injury, keep children
well away and do not allow them to play
with it or to use the controls. They will
not understand the potential dangers
posed by it. They should be supervised
whenever you are working in the
kitchen.
Correct application
This rangehood is designed for
~
domestic use and for use in similar
environments by guests in hotel or motel
rooms, bed & breakfasts and other
typical living quarters. This does not
include common/shared facilities or
commercial facilities within hotels,
motels or bed & breakfasts.
Older children may use the
~
rangehood only when its operation has
been clearly explained to them and
they are able to use it safely. They must
be aware of the potential dangers
caused by incorrect operation.
It must only be used to extract
~
vapours and remove odours from
cooking.
Please be aware that on
~
rangehoods with halogen lighting, the
lamps will get very hot during use and
remain hot for some time after switching
off. To safeguard against burning, keep
children well away from the lamps at all
times.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Installation, maintenance and
~
repairs may only be carried out by a
Before installation, check the
~
suitably qualified and competent
rangehood for visible signs of damage.
Do not install and use a damaged
appliance. A damaged appliance is
dangerous.
person in strict accordance with current
national and local safety regulations.
Repairs and other work by unqualified
persons could be dangerous. The
manufacturer cannot be held liable for
unauthorised work.
Before connecting the appliance to
~
the mains supply, make sure that the
voltage and frequency details given on
the data plate correspond to the on-site
electricity supply, otherwise the
Faulty components must only be
~
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
appliance could be damaged. Consult
a qualified electrician if in any doubt.
The electrical safety of this
~
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with current
local and national safety regulations. It
is most important that this basic safety
requirement is present and tested
regularly and, where there is any doubt,
the household wiring system should be
inspected by a qualified electrician.
During installation, maintenance and
~
repair work, the appliance must be
disconnected from the mains electricity
supply. It is only completely isolated
from the electricity supply when:
– it is switched off at the mains fuse,
– the screw-out fuse is removed (in
countries where this is applicable),
The manufacturer cannot be held liable – it is switched off at the wall socket
for the consequences of an inadequate
earthing system (e.g. electric shock).
and the plug is withdrawn from the
socket, or it is switched off at the
isolator.
For safety reasons, this appliance
~
may only be used when it has been
If the appliance is connected via a
plug: Do not pull the mains
connection cable but the mains plug
to disconnect your appliance from
the mains electricity supply.
fully installed.
Only open the housing as described
~
in the instructions given in the
installation sheet and in the Cleaning
and care section of this booklet. Under
no circumstances should any other
parts of the housing be opened.
Tampering with electrical connections
or components and mechanical parts is
highly dangerous to the user, and can
cause operational faults.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Do not connect the appliance to the
Using at the same time as other
~
mains electricity supply via a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
heating appliances that depend on
the air from the room
Warning - danger of toxic fumes
For appliances with an external fan
~
motor fitted (...EXT models), the
connection of the two units must be
made using the connection cable and
the plug connectors.
These models may only be combined
with a Miele external motor.
This rangehood must not be
~
installed and operated in mobile
installations (e.g. on a ship).
Great care should be taken when
~
In areas which may be subject to
~
using the rangehood at the same time
and in the same room or area of the
house as another heating appliance
which depends on the air in the room.
Such appliances include gas, oil, wood
or coal-fired boilers and heaters,
continuous flow or other water heaters,
gas cooktops or ovens which draw air
in from the room and duct exhaust
gases out through a chimney or
extraction ducting.
infestation by cockroaches or other
vermin, pay particular attention to
keeping the appliance and its
surroundings in a clean condition at all
times. Any damage which may be
caused by cockroaches or other vermin
will not be covered by the warranty.
When used in extraction mode, with or
without an external motor fitted, the
appliance draws air in from the room in
which it is installed and from
neighbouring rooms.
If there is insufficient air, an
underpressure will occur. The heating
appliance may be starved of oxygen,
impairing combustion.
Harmful gases could be drawn out of
the chimney or extraction ducting back
into the room, with potentially fatal
consequences.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
In order to ensure safe operation, and
to prevent gases given off by the
heating appliances from being drawn
back into the room when the extractor
and the heater are in operation
simultaneously, an underpressure in the
room of 0.04 mbar (4 pa) is the
maximum permissible.
Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall vents,
or by other technical measures, such
as ensuring that the extractor can only
be switched on when the heating
appliance is switched off or vice versa.
A ventilation brick alone is not generally
sufficient to ensure safe ventilation.
,The overall ventilation condition
of the dwelling must be taken into
account. If in any doubt, the advice
of a competent builder must be
sought.
If the rangehood is being operated in
recirculation mode, the above
restrictions do not apply.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct use
Do not use the rangehood without
~
the filters in place. This way you will
Never use an open flame beneath
~
avoid the risk of grease and dirt getting
into the appliance and hindering its
smooth operation.
the rangehood. To avoid the danger of
fire, do not flambé or grill over an open
flame.
When switched on, the rangehood
could draw flames into the filter. Fat
particles drawn into the rangehood
present a fire hazard.
The filters should be regularly
~
cleaned or changed as appropriate.
Saturated filters are a fire hazard. See
"Cleaning and care".
When using the rangehood over a
The rangehood can get very hot
~ ~
gas cooktop, ensure that any burners in during cooking due to heat rising from
use are always covered by a pan.
the cooktop.
Switch the cooking zone off when a pan Do not touch the housing or the grease
is removed, even for a short time.
Regulate the flame so that it does not
burn up the sides of the pan.
filters until the rangehood has cooled
down.
Do not use a steam cleaner to clean
~
Do not allow the pans to overheat
excessively (e.g. when using a wok).
The rangehood can become damaged
when exposed to excessive heat.
this appliance. Pressurised steam
could reach the electrical components
and cause a short circuit.
Always switch the rangehood on
~
when a cooking zone is in use,
otherwise condensation may collect in
the hood, which could cause corrosion.
When cooking with oil or fat, chip
~
pans and deep fat fryers etc., do not
leave the pans unattended. Never leave
an open grill unattended when grilling.
Overheated oil and fat can ignite and
could set the rangehood on fire.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Correct installation
Accessories
Refer to the rangehood or cooktop
~
manufacturer's instructions as to
Only use genuine Miele spare parts
~
and accessories with this rangehood. If
whether a rangehood may be operated spare parts or accessories from other
above the cooktop.
manufacturers are used, this will
invalidate the warranty, and Miele
cannot accept liability.
The minimum safety distances
~
between the top of the cooktop and the
bottom of the rangehood given in the
"Appliance dimensions" section of this
booklet must be maintained, unless the
cooktop manufacturer states that a
greater safety distance is required.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
If more than one cooking appliance is
fitted beneath the rangehood, and they
have different minimum safety
distances to the rangehood, select the
greater distance.
Safety regulations prohibit the fitting
~
of a rangehood over solid fuel stoves.
All ducting, pipework and fittings
~
must be of non-flammable material.
These can be obtained from Miele or
from builders' merchants.
The appliance must not be
~
connected to a chimney or vent flue
which is in use. Neither should it be
connected to ducting which ventilates
rooms with fireplaces.
If exhaust air is to be extracted into
~
a chimney or ventilation duct no longer
used for other purposes, seek
professional advice.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
a Telescopic extension piece
b Tower
m Touch control for grease filters
The indicator lamp for the grease filters
lights up when the grease filters need
to be cleaned.
c Canopy
d Control panel
The touch control is used to reset the
operating hours counter every time the
grease filters are cleaned (see
"Cleaning and care").
e Grease filters
f Recirculation grilles
(only for recirculation mode)
g Cooktop lighting
h Charcoal filter
It can also be used to check and alter
the operating hours counter.
n Touch control for the charcoal
filter
(special accessory for recirculation
mode)
The indicator lamp for the charcoal filter
lights up when the charcoal filter used
in recirculation mode needs to be
replaced. For this to happen, the
operating hours counter needs to be
activated before the appliance is used
for the first time.
i Touch control for the
cooktop lighting
This control switches the lighting on
and off, and is also a dimmer switch.
j Touch control for the fan
The touch control is used to reset the
operating hours counter every time the
charcoal filter is replaced (see
"Cleaning and care").
k Touch controls to select the fan
power level
l Touch control for the run-on
option
It can also be used to check and alter
the operating hours counter.
To activate the run-on option. The fan
can be set to switch off automatically
after either 5 or 15 minutes.
For information about using the
appliance, see "Operation".
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Description of the functions
The rangehood works with
. . . air recirculation:
(available as an optional extra with a
conversion kit and charcoal filter: see
"Technical Data")
. . . air extraction:
The air is drawn in and cleaned first by
the grease filter and then by a charcoal
filter. The cleaned air is then
The air is drawn in and cleaned by the
grease filters and directed outside.
recirculated back into the kitchen
through grilles in the top of the
rangehood extension piece.
If the on-site ventilation system does
not have a non-return flap, the
non-return flap supplied with the
appliance must be fitted in the exhaust
socket in the motor unit.
Before using the rangehood in
recirculation mode, ensure that the
charcoal filter is in place. See
"Cleaning and care".
Having a non-return flap fitted in the
ducting ensures that air, once ducted
to the outside, cannot get back into the
room again.
The flap is closed when the rangehood
is switched off.
. . . an external motor:
When the rangehood is switched on,
the non-return flap opens for the
cooking vapours to be blown directly
outside.
(Models ...EXT)
Please note, the performance of
this rangehood hinges greatly on
the installed ducting to vent the
vapours. Poor choice of ducting
results in poor rangehood
The EXT models are designed to be
connected to an external motor located
outside the room.
performance. For ducting
The external motor is connected to the
rangehood by means of a control cable,
and is operated by the controls on the
rangehood.
recommendations, please refer to
the relevant section in these
operating instructions or contact a
specialised installer.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Miele|home
Con|ctivity
– When the cooktop is switched on,
the cooktop lighting and the
rangehood fan also switch on.
– During cooking the rangehood
automatically sets the fan's power
level according to the number of
cooking zones in operation and their
power levels.
– After switching the cooktop off, the
fan and the cooktop lighting will
switch off automatically after a period
of time.
For detailed information about this
function, please read the separate
instruction booklet supplied with the
XKM 2000 DA communication module.
This rangehood is communication
enabled.
Communication module XKM 2000 DA
a, available as an optional extra,
enables the operation of the rangehood
to be automatically controlled by the
operating status of a Miele electric
cooktop with onset controls.
The communication module is fitted to
the rangehood in the area of the fan
and is connected to the controls of the
rangehood.
This module must be installed by a
Miele service technician or suitably
qualified electrician.
For communication to take place, the
cooktop must be fitted with
communication module b.
The cooktop transmits information
about its operating status to the
rangehood via the household power
supply (Powerline) c.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
To switch the fan on
Automatic switch-off of the Intensive
setting
You can set the Intensive setting so that
it only runs for 10 minutes before
reverting automatically to level III.
^ Press the On/Off touch control.
^ To set this option, both the fan and
the cooktop lighting must be
switched off.
The fan runs at power level "II".
The indicator lamp will come on.
To select a power level
^ Press the run-on option touch control
for approximately 10 seconds. The
first fan setting indicator will light up.
^ Use the – / + controls to select the
power level required.
^ Then press in turn,
+ control = higher setting
– control = lower setting
Depending on the intensity of the
cooking vapours, levels I to III are
usually sufficient for normal cooking.
– the touch control for the lighting,
Intensive setting
For short periods of cooking food with
intensive vapours and a strong aroma,
e.g. when searing meat, you may wish
to select the Intensive Setting "IV".
– the – touch control, and
– finally the touch control for the
lighting again.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Run-on option
It is advisable to run the fan for a few
minutes after cooking is finished to
neutralise any lingering odours in the
air, whether you are using air extraction
or recirculation mode.
The indicator lamps for fan power levels
I and IV will flash if the automatic
switch-off for the Intensive setting is not
activated.
The fan can be set to switch off
automatically after either 5 or 15
minutes:
^ Press the + touch control to activate
the automatic switch-off.
The indicator lamps for fan power
levels I and IV will now light up
constantly.
Press the – control to deactivate the
automatic switch-off function.
^ After cooking is finished, press the
run-on option touch control whilst the
fan is still running.
– Press once = The fan will switch off
after 5 minutes (left-hand indicator
lamp).
^ Press the run-on option control to
confirm your selection.
– Press twice = The fan will switch off
after 15 minutes (right-hand indicator
lamp).
If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the original
setting.
To switch off the run-on option, press
the run-on option control again. The
appliance will then not switch off
automatically.
To switch the fan off
^ Press the On/Off touch control to
switch the fan off.
The indicator lamp will go out.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
To switch the cooktop lighting
on
Safety cut-out
Should the rangehood be left on, the
fan will switch off automatically after 10
hours. The lighting will remain on.
The cooktop lighting can be switched
on and off independently of the fan.
^ Briefly press the lighting control to
^ Pressing the On/Off control will
switch on the cooktop lighting.
switch the fan back on again.
The indicator lamp will come on.
Filter operating hours counter
The cooktop lighting will switch on at
maximum brightness.
The number of hours the appliance has
been in operation is stored in memory.
To dim the cooktop lighting
The operating hours counter tells you
when the grease filters or charcoal filter
need to be cleaned or replaced.
The brightness of the lighting can be
adjusted.
^ With the lighting switched on, press
and hold the cooktop lighting control
in.
Resetting the operating hours
counter for the grease filters
After 30 hours of operation (or another
time if the operating hours counter has
been altered), the grease filter indicator
lamp will light up. The grease filters
must then be cleaned.
The brightness will gradually dim until
you release the control.
^ Press the touch control in again to
increase the brightness to the level
required, and then release it.
Afterwards, the filter operating hours
counter must be reset.
If you keep the control pressed in, the
light will continually change between
bright and dim.
To switch the cooktop lighting
off
^ To do this, press and hold the grease
filter touch control in for original
setting 3 seconds while the fan is
switched on.
^ Press the cooktop lighting touch
control briefly to switch the lighting
off.
The indicator lamp for the touch control
will go out.
The indicator lamp will go out.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Reading the operating hours counter Altering the operating hours counter
for the grease filters
for the grease filters
To check the percentage of time set
already used:
The operating hours counter for the
grease filters is set at 30 hours. This
can be lengthened or shortened to suit
the type of cooking you do. You can
choose 20, 30, 40 or 50 hours.
– Select a short time if you roast or fry
a lot.
^ Press the On/Off touch control to
switch the fan on.
– If you use very little fat for cooking,
select a longer time.
– If you only cook occasionally, we
recommend that you still select a
short time, because grease which
has built up gradually over a long
period of time will harden on the
grease filters and make cleaning
more difficult.
^ Press and hold the grease filter touch
control.
One or more of the indicator lamps for
the – / + touch controls will flash.
^ Press the On/Off touch control to
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
switch the fan off.
1 lamp
=
=
=
25 %
50 %
75 %
2 lamps
3 lamps
^ Press the run-on option touch control
and the grease filter touch control at
the same time.
4 lamps = 100 %
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
The indicator lamp for the grease filter
touch control and one of the – / +
indicator lamps will flash.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Activating and altering the operating
hours counter for the charcoal filter
(in recirculation mode)
The charcoal filter is needed for
recirculation mode.
The – / + control lamps show the time
which has been set:
1st lamp from the left = 20 hours
2nd lamp from the left = 30 hours
3rd lamp from the left = 40 hours
4th lamp from the left = 50 hours
On delivery, the operating hours counter
for the charcoal filter is switched off.
For recirculation mode, the operating
hours counter needs to be set to suit
the type of cooking you do:
^ Use the – / + controls to select the
desired time.
^ Press the On/Off touch control to
^ Confirm the selection by pressing the
switch the fan off.
grease filter touch control.
All the indicator lamps will go out.
If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the original
setting.
^ Press the run-on option and the
charcoal filter touch controls at the
same time.
The indicator lamp for the charcoal filter
control and one of the lamps above the
– / + controls will flash.
The – / + control lamps show the time
which has been set:
1st lamp from the left = 120 hours
2nd lamp from the left = 180 hours
3rd lamp from the left = 240 hours
4th lamp from the left = deactivated
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
^ Use the – / + controls to select the
Reading the operating hours counter
for the charcoal filter
desired time.
To check the percentage of time set
already used:
^ Confirm the selection by pressing the
charcoal filter touch control.
All the indicator lamps will go out.
^ Press the On/Off touch control to
switch the fan on.
If you do not confirm your selection
within 4 minutes, the rangehood will
automatically revert to the original
setting.
^ Press and hold in the charcoal filter
touch control.
Resetting the operating hours
counter for the charcoal filter
One or more of the indicator lamps for
the – / + touch controls will flash.
The indicator lamp for the charcoal filter
control will light up after the rangehood
has operated for the number of hours
set. The charcoal filter must then be
replaced with a new one.
The number of flashing lamps shows
the percentage of the operating time
which has already been used up.
1 lamp
=
=
=
25 %
50 %
75 %
2 lamps
3 lamps
Afterwards, the filter operating hours
counter must be reset.
4 lamps = 100 %
^ Press and hold the charcoal filter
touch control for about 3 seconds
while the fan is switched on.
The number of operating hours used
remains in the memory, even when the
appliance is switched off or there is a
power cut.
The indicator lamp for the charcoal filter
touch control will go out.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
^ All external surfaces and controls can
be cleaned using the Original Miele
all purpose microfibre cloth, or with
water and a small amount of
,Before carrying out any cleaning
or maintenance work, disconnect
the rangehood from the mains
supply. Ensure that:
washing-up liquid applied with a well
wrung-out soft sponge or cloth.
– it is switched off at the wall socket
and the plug withdrawn, or
^ Wipe the surfaces dry using a soft
– the mains fuse is withdrawn, or
– the screw-out fuse is removed (in
countries where this is applicable).
cloth.
Do not use too much water when
cleaning the controls. Water could
penetrate into the electronics and
cause damage.
,Exercise caution when changing
halogen lamps. They get very hot
during use, and remain hot for some
time after being switched off. Do not
touch the surface directly when
changing a lamp, as grease particles
from your fingers will adhere to the
surface and damage it.
Do not use:
– cleaning agents containing soda,
acids, chlorides or solvents,
– abrasive cleaning agents e.g.
powder cleaners or cream cleaners,
and abrasive sponges, e.g. pot
scourers or sponges which have
been previously used with abrasive
cleaning agents. These will damage
the surface material.
The halogen lamps can also be
damaged if water is used to clean
them.
Wait several minutes after switching
off before beginning cleaning.
A range of Miele branded cleaning and
conditioning agents are available to
order through your Miele Chartered
Agent, from Miele or via the internet at
Important for appliances with
stainless steel housing
(This infomation does not apply to the
controls)
Stainless steel surfaces can be cleaned
using the Original Miele all purpose
microfibre cloth, or with a proprietary
non-abrasive cleaning agent designed
specifically for use on stainless steel.
Housing
General notes
The surfaces and controls are
susceptible to scratches and
abrasions. Please observe the
following cleaning instructions.
To help prevent re-soiling, a proprietary
conditioning agent for stainless steel
can also be used. Follow the
manufacturer's instructions on the
packaging.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Important for appliances with special Grease filters
finish
The re-usable metal grease filters in the
appliance remove solid particles
(grease, dust, etc.) from the kitchen
vapours, preventing soiling of the
rangehood.
(Titanium and special order finishes)
Please follow the information given in
“General notes" earlier in this section.
However, please be aware that it is very
difficult to clean this type of surface
without causing minor marks to the
surface material.
This can become particularly
noticeable with darker colours and if
there is halogen lighting in the kitchen.
The grease filters should be cleaned
regularly (at least every 3-4 weeks) to
avoid a build-up of grease but always
clean immediately if the grease filter
touch control lamp comes on.
Controls
The controls may suffer
discolouration or damage if soiling is
left on them for too long. Remove
soiling straight away.
,An oversaturated filter is a fire
hazard.
Please observe the "General notes" on
cleaning.
Do not use stainless steel cleaning
agents on the controls.
^ To take out the grease filters, release
the locking clip on the filter, lower the
filter 45°, unhook it at the back and
remove it.
To avoid damaging the filter or the
cooktop below, make sure you hold
the filter securely at all times when
handling it.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the grease filters by hand
When removing the filters for cleaning,
also clean off any residues of oil or fat
from the now accessible housing to
prevent the risk of these catching fire.
^ Clean the filters with a soft nylon
brush in a mild solution of hot water
and a small amount of washing-up
liquid.
When putting the grease filters back in
position, ensure that the locking clips
are facing down towards the cooktop.
Do not use:
– cleaning agents containing
descaling agents,
– powder cleaners, cream cleaners or
abrasive all-purpose cleaning
agents,
– oven sprays.
Cleaning the grease filters in the
dishwasher
If the grease filters are inadvertently
replaced upside down, insert a small
screwdriver blade into the slits to
disengage the clip.
^ Place the filters as upright as
possible in the lower basket, with the
short sides upright, and wash on a
65°C programme, ensuring the spray
arm is not obstructed. If a Miele
dishwasher is being used, select the
Sensor wash programme.
^ After replacing the grease filters,
press the grease filter touch control
for approximately 3 seconds to re-set
the operating hours counter.
The indicator lamp will go out.
^ Use a mild dishwasher detergent.
If the grease filters are cleaned before
the operating hours counter has
reached its maximum, the grease filter
touch control should be pressed for
approximately 6 seconds to reset the
counter.
Depending on the cleaning agent
used, cleaning the filters in a
dishwasher can cause permanent
discolouration to the surface.
However, this will not affect the
functioning of the filters in any way.
^ After cleaning, leave the filters to dry
on an absorbent surface before
replacing them.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Fitting and replacing the
charcoal filter
Always replace the charcoal filter im-
mediately if
If the rangehood is connected for
recirculation, a charcoal filter must be
inserted in addition to the grease filters.
It is designed to absorb cooking
odours.
– the indicator lamp for the charcoal
filter touch control lights up,
It is fitted in the canopy above the
grease filters.
or
New filters can be purchased from
your Miele Chartered Agent or from
Miele.
– if it is no longer effective in absorbing
kitchen odours.
It should, however, be replaced at least
every 6 months.
See back cover for contact details,
and "Technical data" for the model
number of the filter.
Used charcoal filters can be disposed
of with the normal household waste.
^ Before fitting or replacing a charcoal
filter, the grease filters must first be
taken out (see previous section for
instructions on how to do this).
^ After fitting the new charcoal filter,
press the charcoal filter touch control
for approximately 3 seconds to re-set
the operating hours counter.
^ Take the charcoal filter out of its
The indicator lamp will go out.
packaging.
If a charcoal filter is replaced before the
operating hours counter has reached
its maximum, the charcoal filter touch
control should be pressed for
approximately 6 seconds to reset the
counter.
^ Insert the charcoal filter into the back
of the charcoal filter frame, then push
up into the frame at the front.
When fitting for the first time:
^ Set the operating hours counter to
suit your requirements (see
"Operation").
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Changing a halogen lamp
^ Before any cleaning or maintenance
work, disconnect the rangehood from
the mains supply. Ensure that:
– it is switched off at the isolator, or
– it is switched off at the wall socket
and the plug is withdrawn, or
– the mains fuse is disconnected, or
– the screw-out fuse is removed (in
countries where this is applicable).
,Exercise caution when changing
halogen lamps. They get very hot
during use and remain hot for some
time after being switched off. Let
them cool down before you change
them.
^ To access the halogen lamp, push
the lamp cover gently upwards. The
cover will open and can be pulled
down.
^ Pull the old halogen lamp out of the
connection socket.
^ Using a cloth or glove, push the new
lamp (12 V, 20 W, G4 cap) carefully
into the connection socket. Please
follow the manufacturer's instructions.
^ Push the cover back up and make
sure it clicks into place.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
In the event of a fault which you cannot
correct yourself, please contact:
– your Miele Chartered Agent or
or
– Miele
You will find the telephone number
and address of Miele on the back
cover of the manual.
Please quote the model and serial
number when contacting Miele. These
are shown on the data plate which is
visible when the grease filters are
removed.
Warranty
The warranty for this appliance is
2 years.
For further information, please refer to
your warranty booklet.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance dimensions
1) Extraction
2) Recirculation
3) Ventilation grille positioned at the top
for recirculation
4) and 5):
(5 is not required for recirculation mode
rangehoods)
The shaded area represents the wall or
ceiling area for the vent cut-out, for
fitting the connection socket and on
EXT models for feeding the connection
cable through to the external motor.
For recirculation mode, only a
connection socket needs to be fitted.
Connection for air extraction
C 150 mm (recommended), or C 125
mm with reducing collar. Please note,
using 125 mm ducting limits through
put and thus rangehood performance.
DA 428-4
DA 429-4
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Appliance dimensions
Safety distance (S)
– When deciding on the safety
distance, please note that 650 mm
may be preferable above electric
cooktops to give more working space.
When planning the installation height
of your rangehood, the minimum
safety distance between the top of a
cooker or cooktop and the bottom of
the rangehood are as follows, unless
a greater distance is specified by
the manufacturer of your cooking
appliance:
– Account should also be taken of the
height of the person who will be
using the rangehood most often.
They should have sufficient space to
work comfortably at the cooktop, and
be able to reach the rangehood
controls with ease.
600 mm above electric cooktops
650 mm above an open grill or deep
fat fryer,
– If positioned too high, extraction will
be inefficient.
650 mm above gas cooktops.
– The height of the cooking appliance
below must be taken into account
when planning the installation height
of the rangehood.
If this rangehood is installed above a
Miele Wok CS 1028 CombiSet
appliance, a minimum safety
distance of 760 mm must be
maintained between the burner and
the lower edge of the rangehood.
See "Warning and Safety" instructions
for further information.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Assembly parts
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
a 3 protective sheets
for use when fitting the tower.
b 1 exhaust connection for exhaust
ducting C 150 mm.
6 screws 5 x 40 mm and
6 x S 8 plugs
c 1 reducing collar
for exhaust ducting C 125 mm.
for securing the wall bracket.
,The screws and plugs are
d 1 non-return flap
designed for use in solid walls only.
For other types of wall construction,
alternative fixings will be required.
Make sure that the wall is able to
take the weight of the rangehood.
for fitting into the exhaust connection
on the motor unit (not needed for
recirculation mode)
e Telescopic wall bracket
for securing the rangehood to the
wall.
f Conversion kit for recirculation
mode
2 x M 6 self-tapping nuts
including directional unit and flexible
aluminium hose with clips (this is not
included, but is available as an
optional extra - see Technical Data).
for securing the appliance.
2 screws 3.9 x 7.5 mm
for securing the tower.
1 lever for dismantling the tower.
Installation instructions
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Dismantling
Before installation, it is important to
read the information given on the
following pages as well as the
"Appliance dimensions" and the
"Warning and Safety instructions" at
the beginning of this booklet.
This is particularly crucial when
using the rangehood at the same
time as a heating appliance that
relies on oxygen from the same
room, which could result in the
build-up of toxic fumes.
Should the appliance ever need to be
dismantled, follow the installation
instructions in reverse order as
described on the installation sheet.
A lever is supplied to assist with the
removal of the tower.
Installation instructions
See enclosed Installation sheet for
instructions on how to install this
appliance.
Protective foil
^ After loosening the fixing screws on
the tower, push the lever between the
tower and the extension piece to
lever the tower out of its fixings.
(on stainless steel appliances)
The housing components have
protective foil around them to prevent
them from transport damage.
Please remove this foil before fitting the
housing components. It can be peeled
off easily.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
– Only use smooth pipes or flexible
hoses made from non-flammable
materials for the extraction ducting.
Important: To avoid the danger of
toxic fumes, please observe the
Warning and Safety instructions.
This is especially crucial when using
the rangehood at the same time as
another heating appliance which
relies on air from the same room.
The rangehood should be installed
according to local and national
building regulations. Seek approval
from the building inspector where
necessary.
– When using an external motor, make
sure that the exhaust ducting is
sufficiently rigid. The external motor
can cause an underpressure which
can result in the exhaust ducting
distorting.
To achieve the greatest possible air
extraction with the lowest noise level,
please note the following:
– To ensure efficient air extraction, the
diameter of the exhaust ducting
should not be less than 150 mm.
– If flat ducting is being used, the
cross-sectional area must not be
smaller than the cross-sectional area
of the exhaust connection.
If exhaust ducting with a diameter of
less than 150 mm, or if flat ducting is
used, the noise level of the
rangehood will increase and
extraction will be less efficient.
– All ducting, pipework and fittings
must be of non-flammable materials.
– The exhaust ducting should be as
short and straight as possible.
– Only use wide radius bends.
– The exhaust ducting should not be
kinked or compressed.
– Ensure that all connections are
strong and airtight.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
– Where ducting is horizontal, it must
be laid to slope away at at least 1 cm
per metre. This is to ensure that
condensate cannot drain back into
the rangehood.
Condensate trap
(optional accessory)
– If the exhaust air is to be ducted into
the open air, the installation of a
telescopic wall vent or roof vent
(available as an optional accessory)
is recommended.
– If the exhaust air is to be ducted into
a vent flue, the ducting must be
directed in the flow direction of the
flue.
For installations in areas where the
exhaust ducting is exposed to cold
temperatures, we recommend
insulating the exhaust ducting and
installing a condensate trap to collect
and evaporate any condensate which
may occur. Condensate traps are
available for C 125 mm or C 150 mm
ducting.
Important:
If the exhaust ducting is to run through
rooms, ceiling space etc. where there
may be great variations in temperature
between the different areas, the
When installing a condensate trap,
ensure that it is positioned vertically
and, if possible, directly above the
exhaust connection. The arrow on the
housing indicates the direction of
air-flow.
problem of condensation will need to
be addressed. The exhaust ducting will
need to be suitably insulated.
rangehoods designed for use with an
external motor (...EXT models) have an
integrated condensate trap.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Connection for air extraction
Silencer
...with air extraction:
(DASD 150, optional accessory)
The silencer not only reduces noise
from the motor outside the house, but
also sounds from outside (e.g. traffic
noise).
For this reason, the silencer must be
positioned as close as possible to the
ducting exit a.
...in recirculation mode:
The silencer needs to be positioned
between the exhaust connection and
the deflector b. Ensure there is
adequate space in the tower for fitting
it.
To achieve even further reductions in
noise levels, a special silencer can be
fitted in the ducting system.
...air extraction with external motor:
To minimise noise from the motor in the
kitchen, the silencer should be
positioned in front of the external motor
c if possible, or if the ducting is long,
above the exhaust connection on the
rangehood d.
In the case of an external motor located
inside the house, fitting a silencer
behind the external motor e reduces
the noise of the motor outside the
house.
In all modes of operation, the most
effective noise reductions are
achieved if two silencers are fitted
one behind the other in the system.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
If the switch is not accessible after
installation, an additional means of
disconnection must be provided for all
poles.
All electrical work should be
undertaken by a suitably qualified
and competent person in strict
accordance with current national
and local safety regulations.
For extra safety, it is advisable to install
a suitable residual current device
(RCD). Contact a qualified electrician
for advice.
Installation, repairs and other work
by unqualified persons could be
dangerous, for which the
Important
manufacturer cannot be held liable.
This appliance is supplied for
connection to an AC 230 V single
phase 50 Hz supply.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
The wires in the mains lead are
coloured in accordance with the
following code:
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
Green/yellow = earth
Blue
= neutral
= live
Brown
WARNING:
The connection data is given on the
data plate. This is visible when the
grease filters have been removed.
Ensure that this data matches the
household mains supply.
THIS APPLIANCE MUST BE
EARTHED
Connection of this appliance should be
made via a suitable isolator which
complies with national and local safety
regulations and the On-Off switch
should be easily accessible after the
appliance has been built in.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation with control module DSM 400
The Miele DSM 400 can be used to
The components of the central
extraction system are not supplied as
standard by Miele.
combine the rangehood with other
components.
It enables the following:
If in any doubt, the advice of a
competent builder must be sought.
Potential free connection
This is used for controlling another
appliance with the help of the
rangehood's On/Off button s.
Connection to a light switch
The control module can be used to
switch on the cooktop lighting on the
rangehood and also to dim it,
depending on model, via a light switch
in the house.
Installation
The potential free contact of the
DSM 400 a can be installed in an
...EXT model, for instance, which is
connected to a central extraction
system.
The tower needs to be removed before
the control module can be fitted to the
fan unit.
The contact can be used to activate a
motorised shut-off flap b which is
installed before the central extraction
system c.
All electrical work must be carried
out by a competent, qualified
electrician.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Total rated load*
Fan performance*
DA 428-4 . . . . . . . . . . . . . . . . . . . 240 W
DA 429-4 . . . . . . . . . . . . . . . . . . . 260 W
Fan motor*. . . . . . . . . . . . . . . . . . 200 W
Cooktop lighting
Extraction power according to
EN 61591
Extraction system C 150 mm:
DA 428-4 . . . . . . . . . . . . . . . . . 2 x 20 W Level I . . . . . . . . . . . . . . . . . . . 200 m3/h
DA 429-4 . . . . . . . . . . . . . . . . . 3 x 20 W Level II. . . . . . . . . . . . . . . . . . . 300 m3/h
Level III . . . . . . . . . . . . . . . . . . 400 m3/h
Voltage . . . . . . . . . . . . . . . . . . . . 230 V
Level IV Intensive Setting . . . . 640 m3/h
Frequency . . . . . . . . . . . . . . . . . . 50 Hz
Extraction system C 125 mm:
AUS, NZ:
Level I . . . . . . . . . . . . . . . . . . . 180 m3/h
Level II. . . . . . . . . . . . . . . . . . . 280 m3/h
Level III . . . . . . . . . . . . . . . . . . 380 m3/h
Plug rating . . . . . . . . . . . . . . . . . . . 10 A
Test marks . . . . . . . . . . Electrical safety Level IV Intensive Setting . . . . 580 m3/h
. . . . . . . . . . . . . . . . . . . . . . C-Tick Mark
Recirculation with charcoal filter:
Electrically suppressed
Level I . . . . . . . . . . . . . . . . . . . 150 m3/h
according to AS/NZS 1044
Level II. . . . . . . . . . . . . . . . . . . 210 m3/h
Level III . . . . . . . . . . . . . . . . . . 330 m3/h
Level IV Intensive Setting . . . . 490 m3/h
Electrical cable length . . . . . . . . . 1.5 m
Weight
Special accessory for recirculation
mode:
DA 428-4. . . . . . . . . . . . . . . . . . . . 18 kg
DA 428-4 EXT . . . . . . . . . . . . . . . . 15 kg
DA 429-4. . . . . . . . . . . . . . . . . . . . 19 kg
DA 429-4 EXT . . . . . . . . . . . . . . . . 16 kg
– Conversion kit DUW 20
– Miele charcoal filter DKF 12-1
* For EXT models, the rated load and
extraction power will depend on the
type of external motor fitted.
EXT models:
Length of connection cable to external
motor. . . . . . . . . . . . . . . . . . . . . . . 1.9 m
36
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / 4511
M.-Nr. 09 201 520 / 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|