Operating instructions
Rotary ironer
B 895 D
en - GB
To avoid the risk of accidents
or damage to the machine it is
essential to read these instructions
carefully before installing and
using it for the first time.
M.-Nr. 05 319 291
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Maintenance and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning the heater plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning the casing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cleaning the water reservoir . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Ironing cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Replacing the ironing cover . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Water reservoir cap
Finger guard
Heater plate
Roller
Temperature selector
Emergency release
Feed-in table
Hanging bar
Control panel
Ironing table
Release catch
Mains connection cable
Foot pedal
Control panel
oC "Temperature" indicator light
Roller speed selector
"On-Off" button I-0
Q "Steam" switch
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and safety instructions
Technical and electrical safety
To avoid the risk of accidents and
damage to the ironer please read
these instructions carefully before
using it for the first time. They
Before setting up the ironer, check it
~
for any externally visible damage.
Under no circumstances should you
use it if it has been damaged. A
contain important information on its
safety, use and maintenance.
damaged appliance may be
dangerous.
If the supply cord is damaged, it
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner.
~
must be replaced by a Miele approved
service technician to avoid a hazard.
Before connecting the ironer, ensure
~
that the connection data on the data
plate (fuse rating, voltage and
connected load) match the mains
electricity supply. If in any doubt,
consult a qualified electrician.
Correct application
This ironer must only be used for
~
ironing articles which were washed in
water and which have a care label
stating that the article is suitable for
machine ironing.
The electrical safety of this
~
appliance can only be guaranteed
when continuity is complete between
the appliance and an effective earthing
system which complies with local and
national safety regulations.
This ironer is not intended for use by
~
persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience or
knowledge, unless they are supervised
whilst using it or have been shown how
to use it correctly by a person
Where there is any doubt, the on-site
electrical wiring should be inspected by
a qualified electrician. The
manufacturer cannot be held liable for
damage or injury caused by an
inadequate earthing system (e.g.
electric shock).
responsible for their safety.
Do not connect the ironer to the
~
mains electricity supply by a
multi-socket unit or an extension lead.
These do not guarantee the required
safety of the appliance (e.g. danger of
overheating).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and safety instructions
This ironer complies with all relevant Correct use
~
local and national safety requirements.
When working with the ironer always
~
Unauthorised repairs could result in
unforeseen dangers for the user, for
which the Miele cannot accept liability.
Repairs should only be undertaken by a
Miele approved service technician.
Ensure current is not supplied to the
ironer until after maintenance or repair
work has been carried out.
wear close fitting clothes. Wide sleeves,
apron strings, ties or scarves could be
taken in by the roller.
Remove any rings, bracelets, or
~
other jewellery before starting to work.
Tie back long hair.
When heated up there is an acute
~
Faulty components must only be
risk of burning:
~
replaced by genuine Miele original
parts. The manufacturer can only
guarantee the safety of the appliance
when Miele replacement parts are
used.
– if the heater plate is touched,
– if the foot pedal is pressed down
while fingers or hands are positioned
between the raised heater plate and
the roller.
The ironer is only completely
~
Do not unscrew the water reservoir
isolated from the electricity supply
when:
~
cap whilst ironing with steam.
Danger of scalding with hot steam.
– it is switched off at the wall socket
and the plug is withdrawn, or
This ironer is not a toy! To avoild the
~
risk of injury do not let children play on
or near it, or with the controls.
Supervise children whilst you are using
it.
– it is switched off at the mains, or
– the mains fuse is disconnected, or
the screw-out fuse is removed (in
countries where this is applicable).
Never use softened or distilled water
~
Do not damage, remove or bypass
in this ironer. This will cause pitting
corrosion in the water reservoir.
~
the safety features, fixtures and control
elements of this ironer.
Do not drape laundry over the
~
Any removable outer panels must be
heater plate when it is heated up. Fire
~
in place, and all moving or electrical parts hazard.
shielded before the ironer is switched on.
Use the swing out bar.
~
This ironer may only be used in
It is designed for hanging laundry on.
~
mobile installations such as ships if a risk After use it should be swung back out
assessment of the installation has been
carried out by a suitably qualified
engineer.
of the way. Take care not to press down
on the bar when it is swung out. There
is a danger that this could tip the ironer
over.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and safety instructions
Switch the ironer off before
~
removing the plug from the socket.
Do not pull it by the cable.
~
Do not lay the connection cable over
~
the heater plate when it is heated up.
This could damage the cable - danger
of electric shock.
Use the cable holders on the ironer to
wind the cable away.
Do not install the ironer in a room
~
where there is a risk of frost occurring.
Frozen water can cause damage to the
water reservoir and steam hose.
In countries where there are areas
~
which may be subject to infestation by
cockroaches or other vermin, pay
particular attention to keeping the
appliance and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the guarantee.
Using accessories
Accessory parts may only be fitted
~
when expressly approved by Miele. If
spare parts or accessories from other
manufacturers are used, this will
invalidate the guarantee, and Miele
cannot accept liability.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and safety instructions.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
It should be unplugged or disconnected
from the mains electricity supply by a
competent person.
The transport and protective packing
has been selected from materials which
are environmentally friendly for disposal
and can normally be recycled. Rather
than just throwing these materials away,
please ensure they are recycled.
Ensure that any plastic wrappings,
bags etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation!
Disposal of your old appliance
or machine
Electrical and electronic appliances /
machines often contain materials
which, if handled or disposed of
incorrectly, could be potentially
hazardous to human health and to the
environment. They are, however,
essential for the correct functioning of
your appliance or machine. Please do
not therefore dispose of it with your
household waste.
Please dispose of it at your local
community waste collection / recycling
centre and ensure that it presents no
danger to children while being stored
for disposal.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving the ironer
Safety
Do not remove the safety device
until the ironer has been set up on
its rollers.
^ To remove it simply pull it off.
Store it in a safe place for future use. It
should be fitted to the ironer again
before moving it (e.g. when moving
house). Fold the ironer up before fitting
it.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Moving the ironer
The ironer is fitted with four rollers.
^ Hold the ironing table securely and
pull on the release catch situated at
the back of the ironing table on the
right hand side.
^ Hold the ironer by the ironing table to
push it or to pull it towards you.
To overcome obstacles such as carpet
edges and doorways, but also to steer
it:
^ Tilt it slightly.
The ironer can be moved either in the
upright position or when folded up.
^ Swing the top section of the ironer to
the horizontal position for using it, or
swing it down in the vertical position
for storage. Then let go of the release
catch.
^ Before folding the ironing away or
moving it, make sure the water
reservoir cap is tightly secured to
prevent spillages.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Connection cable
Dust cover
The mains connection cable is wound
round a hook underneath the ironing
table.
The dust cover which protects the roller
during transit has to be removed.
^ First remove the feed-in table by
lifting it out of the right hand holder,
then pull it out to the left of the roller.
^ Unwind the cable.
Do not insert the plug into the
electrical socket yet.
Then plug the appliance in and
switch it on. The heater plate will
then rise automatically.
N.B. The plug shown is for illustration
only.
^ The protective dust cover can now
be pulled out and off.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Before ironing
Preparation of the working
area
Preparing the laundry
Correct preparation of the laundry is
essential for successful ironing.
To ensure an even distrubution of
steam make sure the ironer is level and
secure and that it cannot roll sideways.
Before ironing, the laundry should be:
– damped down if you are ironing
without steam
– pulled into shape and smoothed out
– sorted
Damping down when ironing without
steam
The laundry needs to be sufficiently
damp, so that when it is passed just
once through the rotary ironer at the
correct temperature, it will come out
smooth and dry. Dampen the laundry
as you would for hand ironing,
preferably several hours beforehand so
that the articles achieve a uniform
degree of dampness throughout.
A height-adjustable chair is useful and
also a flat surface, e.g. a table, to lay
the ironed laundry on.
If a tumble dryer is being used, select a
"Machine iron" programme.
Place close at hand:
– a basket with the laundry ready for
ironing to the left of the rotary ironer,
Use warm water if preparation time is
short and also to redampen.
– a surface for the ironed laundry to
the right of the rotary ironer.
More advice on correct dampness
Shirts, overalls and blouses etc., should
be hung on coathangers immediately
after ironing.
Material
Dampness for ironing
Silk
wrap in a damp cloth to
avoid water marks
Small items can be hung over the swing
out bar.
Synthetics e.g.
Dralon, Nylon,
Polyester etc.
slightly damp to dry
Have some water ready for redamping
the laundry if necessary.
Wool
press under a damp cloth
(e.g. trousers)
Cotton
Linen
slightly damp
quite damp
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Before ironing
Pulling into shape and smoothing
out
Checking the effectiveness of
the finger guard
Pull the dampened laundry into shape
as usual.
The finger guard is a safety feature and
should be checked each time before
the ironer is used.
Smooth out ribbons, straps, seams and
hems.
^ With the ironer switched on, press the
foot pedal right down.
Large items such as table cloths, bed
linen etc should be folded lengthways
into a number of pleats so that they can
be ironed as easily as possible.
– the heater plate comes down onto
the rotating roller.
Sorting
Sort the laundry according to how
much heat is required for ironing. This
way you can start by ironing at a lower
temperature and then gradually
increase the temperature according to
the fabric being ironed.
First iron synthetic fibres such as nylon,
polyester and artificial silk which only
require a low temperature. Then iron
silk, wool, cotton and linen at increasing
temperatures.
^ If you now lift the finger guard, the
roller stops rotating and the heater
plate rises up.
Iron starched items last of all to avoid
any starch deposits from affecting the
finish of other items.
This shows that the finger guard is
working.
Before using the ironer for the first
time:
^ Let go of the finger guard and
remove your foot from the foot pedal.
You may be able to see or feel a 2-3 mm
high ridge along the roller.
^ Press the foot pedal right down agan.
– the heater plate lowers and the
roller rotates.
This will even itself out after about 3 hours
of ironing enabling the under cloth to
settle. It has no effect on the ironing.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Steam
This ironer can also be used with steam
for ironing dry or slightly damp laundry.
,Do not use distilled water on its
own, as this will cause pitting
corrosion on the reservoir.
Ironing with and without steam
If your laundry is sufficiently damp for
ironing you can iron without using the
steam function. Use steam for ironing
dry laundry, or laundry that is only very
slightly damp.
Fill the reservoir to the lower edge of
the neck with tap water. Do not fill it
any higher.
Filling the water reservoir
^ Replace the cap making sure it is
securely tightened. If it is not secure
there is a danger of water leaking out
of the reservoir when the ironer is
folded up again.
Before filling the reservoir with water
switch the appliance off at the
mains.
If the reservoir empties during ironing
the indicator lamp in the steam switch
will go out to remind you that it needs to
be filled.
,Danger of burning! To prevent
the risk of scalding yourself with hot
steam do not open the cap fully. It
can be opened very slightly to
release the steam.
^ Wait until all the steam has escaped
before opening the cap and filling the
reservoir with water.
^ Fill the water reservoir with tap water
with the ironer set up in the working
position. Do not use proprietary
bottled de-ionised water!
There may still be residual water in the
tank. The amount will depend on the
water hardness level and the amount of
limescale present.
^ To make it easier use the screw-on
funnel.
One reservoir is sufficient for approx.
40 minutes of ironing with steam. It
takes approx. 4 minutes for the water to
heat up to the correct temperature for
steam ironing. The heating-up time may
change as a result of limescale building
up in the reservoir.
If the water hardness level in your area
exceeds 3 mmol/l (300 mg/l or 17º dH)
it is advisable to mix the tap water with
distilled water in a ratio of 1:1.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Steam
^ It is advisable to switch off the steam
function during an interruption to
ironing and at the end of ironing.
Emptying the water reservoir
,Before emptying the reservoir
make sure that the water in it has
cooled down and that the roller has
cooled down.
The reservoir should be emptied after
each use to avoid damage from
deposits present in the water (e.g.
chlorine, calcium or copper).
^ The screw-on funnel can be stored
on the cable holder when not in use.
^ Unscrew the water reservoir cap.
^ To make it easier use the screw-on
funnel.
^ Slowly fold the iron up and at the
same time hold a suitable container
(e.g. measuring jug) underneath the
reservoir opening to catch the water.
^ When all the water has run out
replace the cap.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing
Switching on and off
Material
Dot symbol
Temperature
range
Polyester /
ß
ßß
ßßß
I
Low
artificial silk
temperature
Silk /
wool
Medium
temperature
Cottons /
linen
High
temperature
Cool
The I-0 "On-Off" switch is used for
switching the ironer on and off.
To switch on
^ Press the I-0 switch.
– The indicator light in the switch
comes on.
To switch off
^ Turn the temperature selector to the
temperature you wish to use.
^ Press and release the I-0 switch.
– The indicator light in the switch goes
out.
– The oC "Temperature" indicator light
will come on whilst the heater plate is
heating up.
Select the temperature for ironing
(when ironing without steam)
It will go out when the required
temperature has been reached.
The temperature selector is used for
setting the ironing temperature.
With mixed fibre textiles the
temperature should be set to suit the
most heat sensitive fibre in the fabric.
For example an item made from
poly-cotton should be ironed using the
ßß Silk / Wool setting and not the one
for Cottons.
The temperature settings are indicated
by dots around the selector. These dots
correspond to the international symbols
for ironing.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing
Select the temperature for ironing
(when ironing with steam)
Switching the steam on and off
Set the temperature to ßßß, before
selecting steam.
^ Turn the temperature selector to
ßßß Cottons / Linen (high
temperature).
The Q "Steam" button is used for switch
steam on and off.
Settings ß and ßß are not hot enough
for ironing with steam.
To switch on
^ Press the Q switch in
- once the required temperature has
been reached in the heater plate the
light will come on in the switch.
If this light goes out from time to time
during ironing the water reservoir is
empty.
To switch off
^ Press and release the Q switch
- the indicator light in the switch will
go out.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing
Selecting the roller speed
Ironing
There are 5 roller speed settings, from
low (approx. 2 m/min) to high (approx.
4.5 m/min).
The ironing process is controlled by the
foot pedal which has three positions:
A low speed makes it easier to iron
complicated articles such as shirts and
blouses. A lower speed should also be
selected for folded items. Reducing the
speed will enable them to get dry and
smooth in just one or two passes
through the ironer.
Thinner, single thickness items, e.g. tea
towels can be ironed at a higher speed.
– raised (rest position)
– pressing
– ironing
Ironing
^ Press the foot pedal right down.
,Do not reach between the heater
plate and the rotating roller. Danger
of burning and squashing your
fingers.
^ Set the roller speed selector to the
speed you require.
To press:
^ Press the foot pedal right down, then
lift it up a little. The roller will stop
turning and the heater plate will
remain in contact with the laundry.
To raise the heater plate:
^ Take your foot off the pedal.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing
Feeding the laundry in
Removing the feed-in table
^ Arrange laundry along the feed-in The feed-in table can be removed when
table so that it is straight and smooth. ironing shaped garments, e.g. skirts.
^ Then carefully turn the roller by hand
until the laundry makes contact with
the heater plate (keep your fingers
away from the heater plate).
^ First lift it out of the right hand holder,
and then pull it out to the left of the
roller.
Hanging bar
Then:
Ironed laundry can be hung over the
swing out bar to avoid creasing.
^ Press the foot pedal down.
,Take care not to press down on
the bar when it is swung out. There
is a danger that this could tip the
ironer over.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing
Useful tips
After ironing
If creases appear on items being
ironed:
^ Switch the ironer off.
^ Switch off Q "Steam"
Stop the roller and pull the item back
slightly. Smooth it out and if necessary
dampen it with a wet cloth.
^ Set the temperature selector to I
"Cool".
Try to use the full width of the roller to
help the roller cover maintain its shape.
^ Switch off at the socket and withdraw
the plug.
For small items, e.g. handkerchiefs,
alternate between using the right and
left hand sides of the roller.
If the ironer is to be put away:
^ Allow the heater plate to cool down.
^ Empty the water reservoir.
^ Fold the rotary ironer up.
^ Wind up the mains cable.
^ Cover the ironer.
Items with raised buttons should be
ironed face down on to the roller so that
they are pressed into the cushioned
surface.
A cloth should be placed over zips,
metal buttons and hooks to protect the
heater plate during ironing.
Do not install the ironer in a room
where there is a risk of frost
occurring. Frozen water can cause
damage to the water reservoir and
steam hose.
To protect the heater plate do not iron
very bulky or heat-sensitive buttons.
When you have nearly finished ironing
you can turn the temperature selector
to I "Cool" and continue ironing small
items with residual heat.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing
Power cut
In the event of a power cut activate
the emergency release.
If there is a power cut whilst you are
ironing the heater plate will stay in
contact with the roller. This traps the
laundry with the danger of it singeing.
To free it:
^ Pull the emergency release catch
upwards.
– This releases the pressure enabling
the laundry to be pulled forwards
towards you, or downwards off the
roller, depending on how far through
the ironer it had passed.
When power is restored (the indicator
light in the On-Off button comes on)
press the emergency release catch
back down. You can now continue
ironing.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing tips
The following tips are intended as
helpful suggestions to get you
started. With practice you will
probably find alternative ways of
ironing which suit your style of
working.
Tea towels, hand towels,
handkerchiefs, serviettes etc.
Place on the feed-in table with the
straight grain of the fabric towards the
feed-in table. This will prevent the item
going out of shape and it will be easier
to fold.
^ Then pass both sides of the
un-ironed sections through the ironer.
Handkerchiefs and serviettes can be
fed into the ironer horizontally and then
folded and ironed again if wished.
Use the full width of the roller.
Leave the ironed middle section
hanging over the left hand side of the
roller to prevent creases.
Table cloths
^ After folding, table cloths can be
passed through the ironer again if
wished.
To avoid creases iron the middle
section first.
Sheets
Sheets can be ironed in the same way
as table cloths, or if a lengthwise fold is
acceptable they can be folded and
ironed.
Embroidered sections and raised
patterns on linen should be ironed on
the right side first and then from the
reverse.
^ Place the table cloth across the roller
with the ends hanging off either end.
^ Then fold in half.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing tips
Duvet covers
Pillow cases
^ First do up poppers and buttons and
feed this end through the ironer first.
Then iron the whole pillow case from
both sides.
Shirts
Remove the feed-in table for ironing
shirts.
Iron in the following order:
^ Sleeves and cuffs
^ Back
^ First do up poppers and buttons.
Feed this end through the left hand
side of the ironer first. Buttons should
face into the roller.
^ Front
^ Collar
^ Iron duvets in two runs lengthwise.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing tips
Cuffs and sleeves
Back / shoulder yoke
^ Pull sleeves smooth ready for ironing. Shirts with a shoulder yoke:
Do not iron the cuff yet.
^ Fold the yoke along the back seam.
^ Iron the sleeves from the cuff seam to
the underarm seam.
^ Place the shirt side on to the roller
and iron from the left shoulder seam
to the collar.
^ Iron both sides of each sleeve.
Double cuffs should be folded
(button hole to button hole) and
ironed.
^ Then turn the shirt inside out and iron
from the collar to the right shoulder
seam.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing tips
Back
Front
Iron the back in two sections, from the
middle to the side seams.
The fronts are ironed in one pass
together with the lower section of the
back up to the armhole seam.
^ Start with the front left.
^ Pull the shirt over the roller as far as
the yoke seam - or to the collar seam
on shirts without a yoke - and smooth
it out.
^ Smooth the shirt out and then iron
from the armhole to the collar.
^ Turn the shirt inside out to iron the
other side.
^ Iron from the middle of the back to
the armhole seam. Then iron the rest
of the back as far as the side seam
together with the front section.
Iron the second part of the back as the
first section, but with the shirt inside out.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing tips
Collar
Pyjamas
Pyjamas tops should be ironed
following instructions for shirts. Iron
trouser legs on pyjamas separately.
^ Iron one leg from the front and the
other from the back.
^ Iron from the top to the bottom.
^ Then pull into shape and iron to the
waist. Pull the elasticated section
tight.
Aprons and work jackets
Iron workwear jackets like shirts.
Iron the collar from both sides. Do not
iron any buttons!
Aprons
^ Turn the collar and press if wished.
^ Iron any straps as far as the apron
first.
Nightdresses
^ Then iron either to the waistband or
across the apron. Leave the bib
hanging over the left hand side of the
roller.
Iron sleeves, yokes and back on a
nightdress as you would a shirt.
To iron the front:
^ Pull the nightdress over the roller
leaving the sleeves and bodice
hanging over the left hand side of the
roller.
^ Iron starting from the left hand side
seam and finishing at the right hand
side seam. Then adjust the bodice
section on the roller to iron it.
^ If there is a collar follow the
instructions for ironing shirts.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Ironing tips
Pressing trousers
^ Iron each leg separately. Leave the
top of the trousers hanging over the
edge of the roller.
^ Cover with a damp cloth and turn the
roller by hand until the trouser leg is
covered by the heater plate.
^ Do the same to the other trouser leg.
To press skirts
Remove the feed-in table.
^ Pull the skirt over the free end of the
roller as far as the waistband.
^ Cover with a damp cloth.
^ Iron one section at a time.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Cleaning the water reservoir
,Disconnect the ironer from the
electricity supply by switching off at
the wall socket and withdrawing the
plug before any cleaning and
maintenance work.
Limescale deposits in the water
reservoir, caused by hard water, can
cause the steam jets to become
blocked. Should this happen, the
limescale deposits can be removed by
rinsing out the water reservoir with fresh
tap water.
Cleaning the heater plate
Limescale deposits and starch residues
can be removed from the heater plate
using a suitable proprietary cleaning
agent. Make sure that the ironer is cold
before cleaning it. It will be easier to
clean if you pull up the emergency
release catch.
^ Disconnect the appliance from the
electricity supply by switching off at
the socket and withdrawing the plug.
,Allow the ironer to cool down
before rinsing out the reservoir.
Depending on the hardness level of
your water supply, the reservoir will
need to be rinsed out with tap water
after every 3 to 10 fills of the reservoir.
Do not use any abrasive cleaning
agents.
Cleaning the casing
Stubborn limescale deposits can be
removed with a proprietary descaling
agent.
Depending on how dirty it is, the casing
can be wiped down with a dry or a
damp cloth.
Make sure that you follow the
manufacturer's instructions on
dosage, concentration and how long
it should be used for.
Do not use any abrasive cleaning
agents.
^ Fill the water reservoir approximately
half full (0.4 litres) with a solution of
descaling agent and replace the cap.
^ Roll the ironer backwards and
forwards several times.
^ To prevent the risk of damaging
laundry when next ironing with steam,
the resevoir should be rinsed out
twice with fresh tap water after
descaling it.
For instructions on filling and emptying
the reservoir see "Steam".
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
Ironing cover
Replacing the ironing cover
The ironing cover is 100% cotton with
woven edges and is wound round the
roller twice for maximum moisture
absorption. When washed it will only
shrink up to a maximum of 6% which
means it can be refitted easily. The
cotton undercloth attached to the roller
prevents the ironing cover from
slipping.
,The ironing cover should only be
changed when the appliance is
cold.
^ Remove the feed-in table.
If laundry does not pass sufficiently
smoothly through the roller or if the
cover is particularly soiled it can be
washed at 60°C using a proprietary
detergent.
It is normal for the ironing cover to
become slightly brown with use. If,
however, the cover begins to look very
unsightly, it can be replaced easily.
Ironing covers are available from your
Miele dealer or the Miele Spare Parts
Department.
^ Undo the ironing cover cords at each
end of the roller.
^ Unwind the cover.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
^ Completely unwind the cotton
undercloth attached to the roller and
let it hang down smoothly.
^ Insert the raw edge of the new
ironing cloth into the retaining slot
with the wrong side down. Keep side
ties hanging free and smooth out.
^ Take hold or the cloth by each side
edge and keeping it taut place over
the heater plate.
^ Turn the roller by hand in the
direction you iron (see arrow) until the
cover retaining slot is at the bottom.
The slot which holds the cotton
undercloth is now at the top.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and care
^ Switch on the ironer.
After the roller has gone through three
or four revolutions and the end of the
ironing cover is under the heater plate:
^ Switch off the appliance while
keeping the foot pedal pressed
down.
The ironing cover is held firmly in
place by the heater plate which is still
lowered.
^ Press the foot pedal and "iron" the
cloth round.
Do not let the cords get under the cloth
as it turns.
^ Tighten the cords at the left and right
hand sides of the roller, tie together
and tuck in.
^ Put the feed-in table back in place.
^ Switch the ironer on - the heater plate
will rise up.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes, minor faults in the performance of the
appliance, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical equipment should only be carried out by a suitably
qualified person in accordance with local and national safety regulations.
Repairs and other work by unqualified persons could be dangerous. The
manufacturer cannot be held liable for unauthorised work.
Problem
Possible cause
Remedy
The ironer will not
operate.
There is no power to Check whether
the appliance. - the mains plug is plugged in
and switched on.
- the fuse or circuit breaker has
tripped.
Laundry does not pass The ironing cover is Wash the cover at 60°C using a
smoothly through the dirty.
proprietary detergent.
roller.
Laundry does not pass There are calcium
Remove these with household
smoothly through the deposits (from hard washing up liquid or a suitable
roller.
water) or starch
residues on the
heater plate.
proprietary cleaning agent.
Folds have formed in
the ironing cover.
The heater plate is
dirty (calcium
deposits).
Clean the heater plate with
household washing up liquid or
a suitable proprietary cleaning
agent.
The ironing cover is
very dirty.
Soiling.
Wash the cover at 60°C using a
proprietary detergent.
The heater plate has
no contact pressure.
The emergency
release catch has
been pulled up.
Push the emergency release
catch down (see also "Power
cut").
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
There is no steam.
The water reservoir Fill the water reservoir.
is empty.
The indicator light in
Turn the temperature selector to
ßßß and wait until the indicator
light comes on.
the steam switch goes The required
out during ironing.
temperature for
steam has not been
reached.
The steam jets are
spitting.
Pure de-ionised
water has been
used.
Empty and rinse out the water
reservoir and then fill it with tap
water, see "Maintenance and
care".
A small amount of
There are calcium
Remove these deposits by
water is coming out of deposits from hard rinsing the water reservoir with
the steam jets. water in the water tap water, see "Maintenance and
reservoir. care".
33
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
In the event of a fault, please contact:
– your Miele dealer or
– the nearest Miele Service
Department, (see address on the
back page).
When contacting Miele, please quote
the Model and Serial number of your
appliance, both of which are shown on
the data plate, located at the front
underneath the ironing table.
a Model
b Serial number
c Voltage / frequency
d Fuse rating
e Total rated load
The wiring diagram is located at the
front right hand side of the ironing table
behind the plastic cover.
Please note that telephone calls may
be monitored and recorded for
training purposes.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Height
95.9 (folded up 105.2) cm
Width
98.5 (folded up 50) cm
38.0 cm
Depth
Weight
39 kg
max. load
382 Newton
Water reservoir capacity
Voltage
0.8 litres
see data plate
see data plate
see data plate
Radio/TV suppressed, VDE
Rated load
Fuse rating
Test certificates awarded
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved/0608
M.-Nr. 05 319 291 / 09
Download from Www.Somanuals.com. All Manuals Search And Download.
|