Miele Dishwasher G892 User Manual

Operating instructions  
Platinum  
G 892  
G 892 SC  
To prevent accidents  
and machine damage,  
read these instructions  
before  
UV  
installation or use.  
M.-Nr. 05 431 352  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Contents  
Operation  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
WARNING –  
Do not use an extension cord to  
connect this appliance to  
When using your dishwasher, follow  
basic precautions, including the  
following:  
electricity. Extension cords do not  
guarantee the required safety of the  
appliance (e.g. danger of overheating).  
Be certain your appliance is  
properly installed and grounded by  
a qualified technician. To guarantee the  
electrical safety of this appliance,  
continuity must exist between the  
appliance and an effective grounding  
system. It is imperative that this basic  
safety requirement be met. If there is  
any doubt, have the electrical system of  
the house checked by a qualified  
electrician. The manufacturer cannot be  
held responsible for damages caused  
by the lack, or inadequacy of, an  
effective grounding system.  
Read all instructions before  
installation or use of the dishwasher  
to prevent injury and machine  
damage.  
The manufacturer cannot be held  
responsible for damage or injury  
caused by improper use of this  
appliance.  
Use the dishwasher only for its  
intended purpose. This appliance is  
intended for residential use only.  
Installation  
Keep these operating instructions in  
a safe place and pass them on to  
any future user.  
Installation and repair work should  
be by a Miele authorized service  
technician. Work by unqualified  
persons could be dangerous and could  
void the warranty.  
, WARNING - Fire hazard  
Do not cover or crush the plug of  
an electric appliance. Ensure that the  
cabinet opening for the dishwasher  
provides ample space for the plug.  
Installing the dishwasher in a tight  
space may crimp the power cord or put  
pressure on the plug which may cause  
overheating.  
Electrical safety  
Before installation make sure that  
the voltage and frequency listed on  
the data plate correspond with the  
household electrical supply. This data  
must correspond to prevent injury and  
machine damage. Consult a qualified  
electrician if in doubt.  
Before installation or service,  
disconnect the power supply to the  
work area by unplugging the unit,  
“tripping” the circuit breaker or  
removing the fuse.  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
IMPORTANT SAFETY INSTRUCTIONS  
This equipment is not designed for Use  
maritime use or for use in mobile  
Only use the dishwasher if all  
installations such as caravans or  
panels are properly in place.  
aircraft. However, under certain  
conditions it may be possible for an  
installation in these applications. Please  
contact the nearest Miele dealer or the  
Miele Technical Service Department  
with specific requirements.  
Do not tamper with the controls.  
To reduce the risk of injury, do not  
allow children to play in, on, or  
near the dishwasher.  
Inspect the dishwasher for  
shipping damage. Do not install or  
operate a damaged unit. Contact the  
place of purchase.  
Do not abuse, sit, or stand on the  
door or baskets of the dishwasher.  
Under certain conditions, hydrogen  
gas may be produced in a hot  
Ensure that any plastic wrappings,  
bags etc. are disposed of safely  
and kept out of the reach of babies and  
young children. Danger of suffocation!  
water system that has not been used  
for two weeks or more. HYDROGEN  
GAS IS EXPLOSIVE. If the hot water  
system has not been used for such a  
period, turn on all hot water faucets and  
let water flow from each for several  
minutes before using the dishwasher.  
This will release any accumulated  
hydrogen gas. Do not smoke or use an  
open flame during this time.  
This dishwasher should only be  
installed under a continuous  
countertop secured to adjacent  
cabinetry.  
Do not install this dishwasher  
beneath a cooking surface, oven or  
any appliance that radiates heat.  
High temperatures from these units may  
damage the dishwasher.  
Do not wash plastic items unless  
they are labeled "dishwasher safe"  
or the equivalent. For items not labeled,  
check the manufacturer’s  
Do not, under any circumstances  
cut the intake hose or submerge in  
liquid. This hose contains electrical  
components that could cause injury or  
property damage if cut or submerged.  
recommendations.  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
IMPORTANT SAFETY INSTRUCTIONS  
When loading tableware, place  
sharp items away from the door  
seal to prevent damage to the seal.  
Load knives pointing downwards to  
prevent injuries.  
Disposal of an appliance  
If the appliance is removed from its  
installation and will not be used,  
the door to the wash cabinet should be  
removed to prevent children from being  
Only use detergents and rinse aids locked in the machine. When  
recommended for residential  
dishwashers. Keep all detergents and  
rinse aids out of the reach of children.  
discarding an old dishwasher, unplug it  
from the power outlet, remove the door  
to the wash cabinet and cut off the  
power cord.  
Do not drink water from the  
dishwasher! Harmful residues  
could be present.  
SAVE THESE  
For dishwashers with visible heating  
element  
INSTRUCTIONS  
Do not touch the heating element  
during or immediately after use.  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONSIGNES DE SÉCURITÉ  
AVERTISSEMENT –  
Au moment d’utiliser votre  
lave-vaisselle, prenez des  
précautions essentielles, dont :  
Sécurité électrique  
Avant l’installation, assurez-vous  
que la tension et la fréquence indi-  
quées sur la plaque signalétique cor-  
respondent bien à celles de  
l’alimentation électrique de la résidence  
afin de prévenir les blessures et éviter  
d’endommager l’appareil. Dans le  
doute, consultez un électricien qualifié.  
Lisez attentivement l’ensemble des  
consignes avant d’installer ou  
d’utiliser le lave-vaisselle afin de  
prévenir les blessures et éviter  
d’endommager l’appareil.  
Avant l’installation ou l’utilisation,  
coupez l’alimentation électrique,  
soit en débranchant l’appareil, soit en  
faisant basculer le disjoncteur ou en  
enlevant le fusible.  
Le fabricant ne peut être tenu  
responsable de dommages ou  
blessures causés par l’usage  
inapproprié de l’appareil.  
N’utilisez pas de rallonge pour  
brancher l’appareil à la source  
d’alimentation électrique. Les rallonges  
ne garantissent pas la sécurité requise  
pour l’appareil - si vous utilisez une ral-  
longe, cela peut causer la surchauffe.  
Tout usage inapproprié est  
déconseillé. Cet appareil est  
destiné à un usage domestique  
uniquement.  
Assurez-vous que votre appareil  
est installé correctement et mis à la  
terre par un technicien qualifié. Pour  
garantir la sécurité électrique de  
l’appareil, il faut le raccorder à un dis-  
positif de mise à la terre approprié. Il  
est essentiel de respecter cette exi-  
gence de base en matière de sécurité.  
Dans le doute, faites vérifier  
Conservez ces consignes dans un  
lieu sûr et transmettez-les à tout  
utilisateur futur.  
l’installation électrique de la résidence  
par un électricien qualifié. Le fabricant  
ne peut être tenu responsable de dom-  
mages causés par l’absence d’un dis-  
positif de mise à la terre ou par un dis-  
positif inadapté.  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
CONSIGNES DE SÉCURITÉ  
Installation  
Vérifiez si votre lave-vaisselle n’a  
pas subi de dommage lors du  
transport. N’installez pas et n’utilisez  
pas un appareil endommagé. Commu-  
niquez avec le point de vente où vous  
l’avez acheté.  
L’installation et les réparations de-  
vraient être effectuées uniquement  
par un technicien de service autorisé  
Miele. Les travaux effectués par des  
personnes non qualifiées peuvent  
s’avérer dangereux et rendre nulle la  
garantie.  
Assurez-vous que les emballages,  
les sacs, matières plastiques et au-  
tres sont correctement éliminés et tenus  
hors la portée de bébés et d’enfants.  
Risque de suffocation!  
, ATTENTION - Risque d’incendie  
Ne recouvrez et n’écrasez jamais  
la fiche d’un appareil électrique. Assu-  
rez-vous que dans l’espace occupé par  
le lave-vaisselle il y a suffisamment de  
volume libre pour la fiche. Si vous ins-  
tallez le lave-vaisselle dans un espace  
trop petit, le cordon d’alimentation  
pourrrait être comprimé ou une pres-  
sion pourrait être exercée sur la fiche,  
ce qui risque de causer la surchauffe.  
Le lave-vaisselle doit être installé  
uniquement sous un comptoir  
continu fixé à des armoires adjacentes.  
N’installez pas ce modèle de  
lave-vaisselle sous une plaque de  
cuisson, un four ou tout autre appareil  
qui diffuse de la chaleur.  
Les hautes températures que diffusent  
ces appareils pourraient endommager  
le lave-vaisselle.  
Cet appareil n’est pas conçu pour  
usage sur un bateau ou dans des  
engins mobiles, tels les avions ou les  
véhicules récréatifs. Toutefois, son ins-  
tallation est possible dans certaines cir-  
constances. Veuillez communiquer vos  
exigences particulières au détaillant  
Miele le plus près de chez vous ou au  
service du soutien technique.  
En aucun cas, vous ne devez cou-  
per le tuyau d’arrivée d’eau ou  
l’immerger, car il contient des compo-  
sants électriques qui pourraient causer  
des blessures ou endommager la rési-  
dence.  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
CONSIGNES DE SÉCURITÉ  
Utilisation  
Au moment de charger la vaisselle,  
ne disposez pas les articles cou-  
pants à proximité du joint d’étanchéité  
de la porte afin d’éviter de  
l’endommager. Placez les couteaux  
avec la pointe vers le bas afin d’éviter  
les blessures.  
N’utilisez le lave-vaisselle que  
lorsque tous les panneaux sont  
bien en place.  
Ne jouez pas avec les  
commandes.  
Afin de diminuer le risque de bles-  
sures, ne laissez pas les enfants  
jouer près de l’appareil ni monter de-  
dans ou dessus.  
Utilisez seulement les détergents  
et les produits de rinçage recom-  
mandés pour les lave-vaisselle à usage  
domestique. Conservez tous ces pro-  
duits hors de la portée d’enfants.  
Évitez de malmener la porte ou les  
paniers du lave-vaisselle ou de  
vous y appuyer ou asseoir.  
Ne consommez pas l’eau du  
lave-vaisselle! Elle peut contenir  
des résidus dangereux.  
Dans certaines circonstances, tout  
système d’eau chaude qui n’a pas  
servi durant deux semaines ou davan-  
tage peut produire de l’hydrogène.  
L’HYDROGÈNE EST UN GAZ  
INFLAMMABLE. Si le système d’eau  
chaude n’a pas servi durant une telle  
période, ouvrez tous les robinets d’eau  
chaude et laissez l’eau couler plusieurs  
minutes avant d’utiliser le lave-vaisselle.  
Cette action libérera l’hydrogène qui  
aura pu s’y accumuler. Entre-temps,  
abstenez-vous de fumer et n’utilisez  
pas de flamme nue.  
Lave-vaisselle munis d’un élément  
chauffant visible  
Ne touchez pas l’élément chauffant  
pendant ou immédiatement après  
l’utilisation.  
Mise au rebut de l’appareil  
Si vous désinstallez l’appareil et  
comptez ne plus vous en servir,  
détachez-en la porte pour éviter que  
des enfants se retrouvent enfermés  
dans le tambour. Lorsque vous mettez  
un lave-vaisselle au rebut, débran-  
chez-le de la source d’alimentation  
électrique, détachez-en la porte et cou-  
pez le cordon d’alimentation.  
Ne lavez pas des articles en plas-  
tique non étiquetés "résiste au  
lave-vaisselle" ou une formulation équi-  
valente. Consultez les recommanda-  
tions du fabricant pour les articles non  
étiquetés.  
CONSERVEZ  
CES CONSIGNES  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
Caring for the environment  
Energy saving washing  
This dishwasher is exceptionally  
economical in the use of water and  
electricity. For best results follow these  
tips:  
^ For lowest energy consumption and  
the gentlest washing of china and  
crystal, connect the dishwasher to a  
cold water source.  
^ For fastest possible wash times, yet  
higher energy consumption, connect  
the dishwasher to a hot water source.  
^ Make full use of the baskets without  
overloading for the most economical  
washing.  
^ Choose a program that best suits the  
degree of soiling and the type of  
dishes being washed.  
^ For small loads:  
Select the "Top Solo" feature (see  
"Additional features").  
^ If baskets are only half full, select the  
"Economy" program.  
^ Use the correct amounts of detergent  
and rinse aid.  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Guide to the dishwasher  
Wash cabinet  
1
2
Upper spray arm (not visible)  
7
8
9
Four height adjustable feet  
Triple Filter System  
Salt reservoir  
Cutlery tray  
(select models)  
3
4
Upper basket  
10 Detergent dispenser  
Water feed for  
the middle spray arm  
11 Rinse aid reservoir  
(with dosage selector)  
5
6
Middle spray arm  
Lower spray arm  
12 Data plate  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Guide to the dishwasher  
Control panel  
13 "On/Off" button  
18 "Top Solo" button  
19 Program selection buttons  
20 Child Safety Lock  
21 Door release  
14 Program list / indicators  
15 Check / Refill indicators  
16 Program sequence display  
17 "Start/Stop" button  
22 Drying vent  
Every dishwasher is tested before leaving the factory. Any water remaining in  
the machine is from these tests and does not indicate that the machine has  
been used.  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
To open the door  
Child Safety Lock  
The yellow key for the Child Safety  
Lock is shipped on one of the spikes  
at the front of the upper basket.  
Remove the key before using the  
dishwasher.  
^ Press the release catch inside the  
door grip.  
If the door is opened during operation,  
the dishwasher will stop running. Once  
the door is closed the program will  
restart.  
The Child Safety Lock is designed to  
prevent children from opening the  
dishwasher.  
To close the door  
^ Push the baskets in.  
^ Use the provided key to lock or  
unlock the dishwasher.  
^ Lift the door and push until it clicks  
into position.  
Horizontal:  
the door is locked  
Vertical:  
the door can be opened  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Water softener  
If your water hardness is consistently  
lower than 8 gr/gal (140 ppm), you do  
not need to add dishwasher salt.  
However, the dishwasher must still be  
programmed to correspond to the local  
water hardness.  
To achieve good cleaning results, the  
dishwasher needs soft water. Hard  
water results in calcium deposits on  
dishware and in the dishwasher.  
If your tap water hardness is above  
8 gr/gal (values are in US gallons)  
(140 ppm), the water should be  
softened. This takes place  
Where the water hardness fluctuates  
e.g. between 9 - 17 gr/gal (160 - 310  
ppm), always program the machine to  
the higher value, 17 gr/gal (310 ppm) in  
this example.  
automatically in the unit’s integrated  
water softener.  
– Your local water authority will be able If there is a fault, it will help the service  
to advise you of the water hardness  
level in your area.  
technician to know the hardness of your  
local water supply.  
– The dishwasher must be  
^ Please note the water hardness:  
programmed to correspond to the  
water hardness in your area.  
gr/gal  
– The water softener must be filled with  
dishwasher salt for reactivation.  
14  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Programming the water softener  
1 - 22 gr/gal:  
Your water hardness level must be  
programmed into the dishwasher using  
the buttons on the control panel.  
^ Use the program selection buttons  
(19) to select the program which  
corresponds to the water hardness in  
your area.  
^ Make sure the dishwasher is turned  
off.  
Table 1  
^ Press and hold the "Start/Stop" button  
(17) and at the same time turn on the  
dishwasher with the "On/Off" button  
(13). Release the "Start/Stop" button  
within two seconds.  
gr/gal*  
1 - 4**  
ppm  
Program indicator  
Pots & Pans  
Sani Wash  
20 - 70  
5 -  
7
90 - 130  
140 - 180  
200 - 230  
250 - 290  
310 - 400  
8 - 10  
11 - 13  
14 - 16  
17 - 22  
Normal Plus  
Normal  
The "Rinse" (16) indicator and a  
program indicator will light and the  
"Salt" (15) indicator will flash.  
Economy  
Rinse & Hold  
If this is not the case, the above steps  
must be repeated.  
* US gallons  
** Factory preset  
If your water hardness is greater  
than 22 gr/gal (400 ppm) proceed to  
the next page.  
To store the programmed water  
hardness:  
^ Press the "Start/Stop" (17) button  
twice.  
^ Turn off the dishwasher.  
15  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
23 - 70 gr/gal:  
Checking the programmed water  
hardness  
^ Press the program seletion button %  
(19) until the "Rinse" (16) indicator  
flashes.  
^ Make sure the dishwasher is turned  
off.  
This is the second program level.  
^ Press and hold the "Start/Stop" button  
(17) and at the same time turn on the  
dishwasher with the "On/Off" button  
(13). Release the "Start/Stop" button  
within two seconds.  
^ Use the program selection buttons  
(19) to select the program which  
corresponds to the water hardness in  
your area.  
The programmed water hardness will  
be indicated by:  
Table 2  
gr/gal  
ppm  
Program indicator  
Pots & Pans  
1 - 22 gr/gal  
23 - 35 410 - 630  
36 - 70 650 - 1260  
Lit program indicator (see table1).  
Lit "Rinse" (16) indicator.  
Sani Wash  
The selected program indicator (14)  
and the "Rinse" (16) indicator will flash.  
23 - 70 gr/gal  
Lit program indicator (see table 2).  
Flashing "Rinse" (16) indicator.  
To store the programmed water  
hardness:  
^ Press the "Start/Stop" button (17)  
twice.  
^ Turn off the dishwasher.  
^ Turn off the dishwasher.  
16  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Filling the salt reservoir  
To fill the salt reservoir:  
If your water hardness level is greater  
than 8 gr/gal, the salt reservoir should  
be filled before the first use and when  
the "Salt" indicator lights.  
^ Remove the lower basket.  
^ Unscrew and remove the salt  
reservoir cap located on the floor of  
the wash cabinet.  
Only use water softener salt specially  
formulated for dishwashers. Other salts  
may contain insoluble additives which  
can impair the water softener.  
^ Place the provided funnel over the  
salt reservoir.  
The salt reservoir must be filled with  
2 quarts (2 l) of water before adding  
salt for the first time. Water does not  
have to be added with subsequent  
refills.  
The proper salt can be purchased from  
your Miele dealer or Miele’s Technical  
Service Department.  
,Inadvertently filling the salt  
reservoir with dishwashing  
detergent will damage the water  
softener.  
^ Carefully fill with salt. The salt  
reservoir holds approximately 4.5 lbs  
(2 kg) of salt. As it is filled, water will  
run out.  
^ Clean any excess salt from the  
threads of the reservoir opening.  
^ Screw the cap on firmly.  
^ If the dishwasher will not be used  
immediately, run the "Rinse & Hold"  
program. This will remove any traces  
of salt from inside the wash cabinet.  
17  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Before using for the first time  
Salt indicator  
Bypassing the salt indicator  
When the salt reservoir is empty, the  
"Salt-PC" indicator will light, indicating  
that it should be refilled with  
reactivation salt.  
If your water is soft (below 8 gr/gal) the  
salt reservoir should not be filled with  
salt. The indicator will remain lit and  
should be disregarded or bypassed.  
^ Remove the salt reservoir cap.  
Looking into the salt reservoir, you will  
see the top of the float chamber on the  
right hand side, a.  
After the reservoir has been filled, the  
water softener is automatically  
reactivated the next time the  
dishwasher is started. The "Salt"  
indicator will be lit during this process.  
^ Using a screwdriver, carefully pivot  
the float chamber towards the center  
of the reservoir.  
^ Using needle nose pliers, pull the  
cap, b, off of the float chamber, and  
remove the float, c.  
Replace the float chamber cap, push  
the chamber back into its upright  
position, and replace the salt reservoir  
cap. The "Salt" indicator should no  
longer be lit.  
18  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Rinse aid  
Rinse aid is recommended to prevent  
spotting on dishes and glassware.  
,Filling the rinse aid reservoir with  
detergent will damage the reservoir.  
Only pour rinse aid formulated for  
residential dishwashers into the  
reservoir.  
Adding rinse aid  
^ Pour liquid rinse aid into the reservoir  
until it is visible on the surface of the  
screen.  
^ Press on the flap until you hear it  
click shut. Failure to close it all the  
way will allow water to enter the  
reservoir during the wash program.  
^ Wipe up any spilled rinse aid. The  
flap will remain closed during normal  
operation.  
^ Add rinse aid before the first use and  
whenever the "Rise aid" indicator  
lights.  
^ Press the button in the direction of  
the arrow until the flap springs open.  
19  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Before using for the first time  
Adjusting the dosage  
Rinse aid indicator  
The rinse aid indicator on the control  
panel will light when the rinse aid  
reservoir needs refilling.  
The dosage selector is preset to 3. This  
dispenses approximately 3 ml of rinse  
aid per program. It can be adjusted  
from 1 to 6.  
When the indicator first comes on, there  
will be enough rinse aid left for 2 - 3  
washes.  
^ Use a higher setting if spots appear  
on dry glassware.  
^ Use a lower setting if streaking  
appears on dishes or glasses.  
20  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
^ The spray arms must not be blocked  
by items that are too tall or hang  
through the baskets. Check  
clearance by manually rotating the  
spray arms.  
,Do not wash items soiled with  
ash, sand, wax, grease or paint in  
the dishwasher.  
Ash and sand do not dissolve and  
will be distributed through out the  
inside of the dishwasher.  
Wax, grease and paint will cause  
permanent discoloration or damage  
to the dishwasher.  
^ Food residue and spilt liquids should  
be cleaned from the sides of the  
dishwasher door. These are outside  
of the wash cabinet and are not  
cleaned by water from the spray  
arms.  
^ Scrape food from dishes before  
placing in the dishwasher.  
Do not rinse dishes.  
^ Load dishes so that water can reach  
all surfaces. Do not place dishes and  
cutlery inside other pieces.  
^ Hollow items such as cups and  
glasses should be placed upside  
down in the upper basket.  
^ Concave based items, such as mugs  
or bowls, should be placed at an  
angle so that water does not pool.  
^ To ensure good water coverage tall,  
narrow, hollow pieces, such as a  
vase, should be placed in the center  
of the basket, rather than in the  
corners.  
^ Small cups and glasses should be  
placed on the cup racks. Taller mugs  
and glasses can be placed beneath  
the rack.  
^ Place very small items in the cutlery  
tray or basket so they do not fall to  
the bottom of the wash cabinet.  
21  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Items not recommended for  
dishwashing  
Glassware:  
– There are no standard guidelines for  
washing glassware but, when in  
doubt wash by hand.  
– Cutlery with wooden handles.  
– Wooden cutting boards.  
– Wash delicate glassware with a low  
temperature program and without the  
extended drying feature to reduce  
the risk of clouding. See the  
– Glued items such as old knives with  
handles glued together around the  
shank of the blade.  
"Program guide".  
– Hand made craft items, antique,  
metal trimmed or decorative  
glassware.  
– If crystal or delicate glasses will be  
washed frequently, connect the  
dishwasher to cold, rather than hot  
water.  
– Lead crystal.  
– Copper, brass, tin or pewter.  
– Clouding or etching may occur on  
glasses after frequent washing.  
– Plastic items that are not heat  
resistant.  
– When purchasing new dishes,  
glasses and cutlery, make sure they  
are dishwasher safe.  
– Dishes with color painted over the  
glaze. These dishes may fade over  
time.  
Silver and aluminum:  
– Cast iron pots and pans.  
– Silver or aluminum items may tarnish.  
– Silverware previously cleaned with a  
silver polish may be damp or spotted  
at the end of a program where water  
has adhered to the polish. This can  
be rubbed off with a soft, dry cloth.  
Silver that has been cleaned in an  
immersion dip is usually dry at the  
end of a program, but may tarnish.  
– If left to dry, foods containing sulfur  
can discolor silver. These include  
egg yolk, onions, mayonnaise,  
mustard, legumes, fish, fish brine  
and marinades.  
– Silverware may tarnish or pit if  
washed next to stainless steel.  
Leave space between these metals.  
22  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Cutlery basket  
^ For the best cleaning results, spoons  
and forks should be placed in the  
basket with handles down. Knives  
and other pointed objects can be  
loaded with their handles up to  
prevent injuries.  
^ Place small spoons into the slots on  
either side of the cultery basket.  
23  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Cutlery tray (SC units)  
Spoon heads should be placed in  
contact with at least one of the serrated  
retainers of the cutlery tray to ensure  
that water runs off freely.  
The removable cutlery tray makes  
unloading flatware easy. Simply carry  
the cutlery tray to where the flatware is  
stored and put the entire basket away  
in one trip.  
For easier unloading cutlery should be  
grouped in zones, one for knives, one  
for forks, one for spoons, etc.  
Place knives with the cutting edge and  
forks with the prongs between the  
holders. Spoons should be placed in  
the opposite direction with the handles  
between the holders.  
Longer items such as soup ladles, cake  
slices, mixing spoons and long knives  
should be placed lengthwise in the  
indentation of the cutlery tray.  
Spoons with thick handles may have to  
be placed as knives and forks with their  
heads in the holders.  
24  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Upper basket  
Adjusting the upper basket  
On select models, the upper basket  
can be raised or lowered to  
accommodate tall items.  
^ Slide out the upper basket.  
Load the upper basket with small,  
lightweight, or delicate items such as  
cups, saucers, glasses, dessert bowls  
and flat pans.  
Long items such as soup ladles, mixing  
spoons and knives can be set across  
the front of the upper basket.  
^ Pull up the levers at the sides of the  
upper basket and adjust the basket  
height.  
^ Release the levers and the basket will  
lock in place.  
The basket can also be angled to fit tall  
items in both, the lower and upper  
baskets. The angles should not be set  
to opposite extremes. This will block the  
middle spray arm. Take care when  
sliding the basket in and out in this  
position.  
25  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Adjustable cup racks  
Coffee bar  
Raise the rack to make room for tall  
glasses. Lower it to double stack  
smaller pieces.  
To allow water to run off the bottom of  
coffee mugs, place slanted on top of  
the coffee bar. The bar can also be  
used to separate two rows of glasses.  
To stack wide items, flip the bar to the  
right.  
26  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Lower basket  
Dishwasher with cutlery tray  
For larger and heavier items such as  
plates, serving platters, sauce pans,  
bowls.  
Dishwasher with cutlery basket  
27  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Loading the dishwasher  
Height limit  
Vase / Bottle holder (select models)  
The bottle holder e.g. for milk or baby  
bottles, can be inserted into the bottom  
basket in more than one place. Position  
in any area marked white in the  
illustration. Do not place the insert in  
the corners of the lower basket, water  
cannot properly cover bottles in these  
areas.  
The guide at the front of the upper  
basket determines the maximum height  
for items placed in the lower basket so  
that the middle spray arm is not  
blocked.  
Foldable spikes  
Two rows of spikes can be folded  
down, to create more room for larger  
dishware e.g. pots, pans and bowls.  
^ Lift up the spike rows and fold them  
one on top of the other.  
28  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Basket accessories  
Additional inserts for the upper and lower baskets may be purchased from your  
Miele dealer or the Miele Technical Service Department.  
Vase / Bottle holder  
to wash milk or baby bottles  
attaches to the lower basket  
Mini Cutlery Basket  
to wash additional cutlery  
for units with cutlery tray  
attaches to the lower basket  
Upper Basket Glassware Insert  
to wash long stemmed glassware  
attaches to the upper basket  
29  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Adding detergent  
,Dishwasher detergents contain  
irritant and corrosive ingredients.  
Keep children away from detergent.  
Do not fill the detergent dispenser  
until you are ready to start the  
dishwasher.  
Only use powder detergents or  
tablets formulated for residential  
dishwashers. The use of gel or liquid  
detergent is not recommended.  
Never fill the detergent dispenser to  
capacity.  
Do not use more than the  
recommended amount of detergent.  
Continued use of too much  
detergent may cause machine  
damage.  
The horizontal marks in Compartment II  
indicate levels of approximately 1 1/4,  
1 3/4 and 2 tablespoons (20, 25 and  
30 ml) respectively.  
^ With the dishwasher door fully open  
fill compartment II with 2 tablespoon  
(30 ml) of powder detergent, or one  
detergent tablet.  
^ Close the cover. The cover will  
always open at the end of a wash  
program except in "Rinse & Hold".  
2 tablespoon (30 ml) of detergent is  
enough for most normally soiled loads.  
For heavily soiled loads, or if food has  
dried on the dishes, a program  
containing a prewash cycle should be  
selected. Add an extra tablespoon (15  
ml) of detergent to compartment I.  
Less detergent is needed in homes with  
very soft water and when washing  
lightly soiled dishes.  
^ To open, press the latch on the  
detergent dispenser.  
30  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Running the dishwasher  
Waterproof System  
^ Make sure the spray arms are not  
blocked.  
All Miele dishwashers are specially  
designed to shut off the water intake  
and drain the wash cabinet in the rare  
event of an internal water valve failure.  
^ Close the door.  
^ Turn on the dishwasher.  
For this feature to be active, the  
The "Start/Stop" indicator (17) will flash  
and a program indicator (14) will light.  
machine must be "On" (not necessarily  
running) and the door must be closed.  
^ Select a wash program using the  
program selection buttons (19). The  
selected program indicator will light.  
Program sequence indicator  
(16)  
The current step of a wash program is  
indicated by the program sequence  
indicator (16).  
^ Refer to the "Program guide" for  
details on wash programs.  
^ Select "Top Solo" if desired. See  
"Additional features".  
^ Press the "Start/Stop" button (17).  
The wash program will begin.  
Do not end a program prematurely!  
Important program steps could be  
omitted (e. g. reactivating the water  
softener).  
31  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
At the end of a program  
Interrupting a program  
The "End" indicator will light when the  
program has finished.  
A program is interrupted as soon as the  
door is opened.  
If the door is closed, the program will  
continue from where it was interrupted.  
^ Turn off the dishwasher.  
^ Open the dishwasher door slightly to  
allow the dishes to cool before  
unloading.  
,Water in the dishwasher may be  
hot. There is a danger of being  
burned! Only open the door if  
absolutely necessary.  
It is advisable to turn off the water  
supply if the dishwasher will not be  
used for a period of time (e.g. while  
vacationing).  
Changing a program  
If a program is running:  
^ Press the "Start/Stop" button (17) for  
at least one second.  
^ Select the new program using the  
program selection buttons (19).  
^ Select "Top Solo" if needed (see  
"Additional features").  
^ Press the "Start/Stop" (17) button.  
The new program will begin.  
If a program has not started:  
^ Use the program selection buttons  
(19) to choose a new wash program.  
32  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Program guide  
Program  
When to use  
Program cycle  
Pre- Main Interim Final Dry-  
wash wash rinse rinse ing  
1 2  
1 2  
Pots & Pans for heavily soiled pots and pans with dried on food  
Main wash temperature 170 °F (75 °C)  
Run-time 128 min  
X X  
X
X
X
-
X
X
X
X
Sani Wash  
extended wash time  
-
X
X X  
for sanitizing normally soiled dishware with dried  
on food  
Main wash temperature 150 °F (65 °C)  
Run-time 142 min  
Normal Plus higher wash temperature helps to clean  
normally soiled dishware with stubborn dried on  
food or greasy residues  
X X  
X X  
X
X
-
X
X
Main wash temperature 150 °F (65 °C)  
Run-time 135 min  
1)  
Normal  
for normal soiled dishware  
Main wash temperature 130 °F (55 °C)  
Run-time 118 min  
X
X
X
X
-
-
X
X
X
X
Economy  
energy saving program  
-
-
for normally soiled dishware  
Main wash temperature 130 °F (55 °C)  
Run-time 85 min  
Rinse & Hold for rinsing dishes when a complete cycle is not needed -  
X
-
-
-
-
-
Run-time 11 min  
1) Standard for Energy Label  
When washing a full load in Pots & Pans, Sani Wash and the Normal programs use at least 2  
tablespoons (30 ml) of detergent.  
For the Pots & Pans program add an additional teaspoon (5 ml) to compartment I.  
1
If "Top Solo" is selected, reduce the amount of detergent to 1 / tablespoons (20 ml).  
4
Program times are based on a hot water connection. If the unit is connected to cold water, program  
times will increase by approximately 25 minutes.  
Usage:  
Electric 0.06 - 2.4 (kWh)  
Water  
1.3 - 6.3 US gallons (5 - 24 L)  
33  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Additional features  
"Top Solo" (18)  
^ Turn the dishwasher on using the  
"On/Off" button (13).  
Using "Top Solo" will save water and  
energy.  
The "Start/Stop" (17) indicator will flash.  
This program is recommended when  
there is only a small load to clean. "Top  
Solo" can be selected with all  
programs.  
^ Select a program using the program  
selection buttons (19).  
^ Press the "Top Solo" button (18).  
The "Top Solo" indicator and the  
selected program indicator will light.  
With this feature, water is directed only  
to the top and middle spray arms in the  
dishwasher. This means that the water  
jets are only aimed at items in the  
upper basket and the cutlery tray.  
^ Press the "Start/Stop" button (17).  
The program will begin.  
The middle spray arm also directs  
water downwards, so lightly soiled  
plates or platters can be placed in the  
lower basket.  
When using this program, do not place  
pots, bowls or other hollow containers  
in the lower basket.  
Because a smaller load is being  
washed the amount of detergent  
recommended can be reduced to 1 1/4  
tablespoons.  
34  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Operation  
Extended drying  
The extended drying time is off if the  
top program indicator flashes.  
If desired drying results are not  
consistently achieved, the turbothermic The extended drying time is on if the  
cooling fan can be programmed to run  
an extra 14 minutes at the end of each  
program.  
top program indicator lights.  
If the the correct drying time is set:  
The "Extended drying" feature can also  
be activated to prevent condensation  
from collecting on the steam deflector.  
^ Turn off the dishwasher.  
If the drying time is incorrect:  
Turning extended drying on/off  
^ Press the "Top Solo" button (18).  
^ Make sure the dishwasher is turned  
off.  
^ Press the "Start/Stop" (17) button  
twice.  
^ Press and hold the "Start/Stop" (17)  
button and at the same time turn the  
dishwasher on using the "On/Off"  
button.  
Release the "Start/Stop" button within  
two seconds.  
The "Start/Stop" (17) indicator will flash.  
The changed extended drying option  
will be stored.  
^ Turn off the dishwasher.  
^ Press the "Top Solo" (18) button.  
The "Salt" (15) indicator will flash and  
the "End" (16) indicator will light.  
If this is not the case, the above steps  
must be repeated.  
35  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Frequently asked questions  
With the aid of the following guide, minor problems can be fixed without a service  
call.  
,Repairs should only be carried out by a qualified and trained person in  
accordance with local and national safety regulations. Unauthorized repairs  
could cause personal injury or machine damage.  
What if …  
Possible fault  
Fix  
the dishwasher does not The door is not properly  
Close the door firmly.  
start?  
closed.  
The machine is not  
plugged in.  
Insert the plug.  
The fuse is defective or  
the breaker has tripped.  
Reset the circuit breaker  
Make sure it is a 15 A  
breaker.  
the dishwasher stops  
during a program?  
The fuse or breaker has  
tripped.  
Reset the circuit breaker  
Make sure it is a 15 A  
breaker.  
the "Intake" indicator is The water valve is closed. Open the water valve.  
lit / flashing?  
The filter in the water inlet See maintenance  
is blocked.  
instructions.  
The waterproof system  
has activated.  
Call the Miele Technical  
Service Department.  
The flow pressure at the  
water inlet is less than  
4.5 psi (0.3 bar).  
Contact a plumber.  
36  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Frequently asked questions  
What if …  
Possible fault  
Fix  
the "Drain" indicator  
The triple filter in the wash Clean the filter, see  
flashes and the program cabinet is clogged.  
maintenance instructions.  
stops?  
The drain pump or the  
Clean the drain pump and  
non-return valve may be the non-return valve, see  
blocked. maintenance instructions.  
The drain hose is kinked. Remove the kink.  
the "End", "Start/Stop" There may be a technical Press the "Start/Stop"  
and "Top Solo"  
fault.  
button.  
indicators flash at the  
same time at the end of  
a program?  
Turn off the dishwasher.  
A few seconds later:  
Turn the dishwasher on.  
Select the desired  
program.  
Press the "Start/Stop"  
button.  
If the indicators flash  
again, there is a technical  
problem.  
Call the Miele Technical  
Service Department.  
37  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Frequently asked questions  
What if …  
Possible fault  
Fix  
there is a knocking  
noise in the wash  
cabinet?  
The spray arm is hitting  
an item in the basket.  
Interrupt the program,  
rearrange items blocking  
the spray arms.  
there is a rattling noise? Items are not secure in  
Interrupt the program and  
rearrange loose pieces.  
the wash cabinet.  
there is a knocking  
noise in the water  
pipes?  
This may be caused by  
the installation or the  
diameter of pipe.  
This has no effect on the  
dishwasher. If in doubt  
contact a plumber.  
the dishes are not dry,  
The rinse aid setting may Increase the dosage or  
glasses and cutlery are be too low, or the rinse aid refill the reservoir, see  
spotted?  
reservoir is empty.  
"Before using for the first  
time".  
Extended drying is not  
activated.  
Activate the Extended  
drying feature.  
Dishes were taken out too Leave dishes in longer.  
soon.  
dishes are not clean?  
The dishes were not  
loaded correctly.  
See "Loading the  
dishwasher".  
The program was not  
powerful enough.  
Select a more intensive  
program, see "Program  
guide".  
Not enough detergent  
was dispensed.  
Use more detergent, see  
"Adding detergent".  
The spray arm jets are  
clogged.  
Clean the spray arm jets,  
see maintenance  
instructions.  
The triple filter is clogged Clean and reseat the filter,  
or not correctly seated.  
see maintenance  
instructions.  
The non-return valve is  
blocked while open.  
Clean the drain pump and  
the non-return valve, see  
Water runs back into the maintenance instructions.  
wash cabinet.  
38  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Frequently asked questions  
What if …  
Possible fault  
Fix  
tea or lipstick stains  
have not been  
completely removed?  
The wash temperature of Select a program with a  
the selected program was higher temperature.  
too low.  
Not enough detergent  
was used.  
Use more detergent.  
white residue is visible Not enough rinse aid was Increase the dosage,  
on cutlery and dishes,  
clouding occurs on  
glassware and film can  
be wiped off?  
used.  
see "Before using for the  
first time".  
The salt reservoir is  
empty.  
Add reactivation salt,  
see "Before using for the  
first time".  
The salt reservoir cap was Reseat it making sure it  
not correctly screwed on. screws back on correctly.  
The programmed setting Raise setting of the water  
of the water softener is too softener , see "Before  
low.  
using for the first time".  
there is a bluish sheen  
on the surface of  
glasses and film can be  
wiped off?  
The rinse aid dosage is  
set too high.  
Reduce the dosage, see  
"Before using for the first  
time".  
glasses are dull and  
discolored and film  
cannot be wiped off?  
Glasses are not  
dishwasher safe.  
There is no remedy.  
Only wash dishwasher  
safe glasses.  
39  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Frequently asked questions  
What if …  
Possible fault  
Fix  
plastic items are  
discolored?  
Natural dyes e. g. from  
vegetables may be the  
cause. Not enough  
Use more detergent, see  
"Adding detergent".  
Discoloration is  
detergent was used to  
break down natural dyes.  
permanent.  
there are rust stains on The salt reservoir cap was Reseat and screw the cap  
cutlery?  
not screwed on properly. on firmly.  
The affected items are not There is no remedy.  
corrosion resistant.  
Only wash dishwasher  
safe cutlery.  
detergent is left in the  
The dispenser was damp Dry the dispenser before  
dispenser at the end of a when detergent was  
program? added.  
the detergent dispenser Detergent residue is  
adding detergent.  
Remove the residue.  
lid can not be closed  
properly?  
blocking the catch.  
water remains in the  
The triple filter in the wash Clean the filter,  
wash cabinet at the end cabinet is clogged.  
of a program?  
see maintenance  
instructions.  
The drain pump or the  
Clean the drain pump and  
non-return valve may be the non-return valve,  
blocked.  
see maintenance  
instructions.  
The drain hose is kinked. Remove the kink.  
40  
Download from Www.Somanuals.com. All Manuals Search And Download.  
After sales service  
In the event of a fault which you cannot  
correct yourself please contact the  
Miele Technical Service Department.  
Program update function - PC  
The Program Correction (PC) allows a  
technician to update the dishwasher to  
make use of new technology.  
U 1-800-999-1360  
V 1-800-565-6435  
When contacting the Miele Technical  
Service Department, please quote the  
model and serial number of your  
appliance.  
These can be found on the data plate  
on the upper inside edge of the  
dishwasher door.  
For example, if a detergent with good  
wash results using only cold water  
becomes available, the wash programs  
can be modified to take advantage of  
this.  
41  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Transport  
To transport the dishwasher, e. g. when  
moving to a new home, note the  
following:  
– Empty the dishwasher.  
– Secure any loose parts, e. g. hoses,  
cables, cutlery baskets.  
– Transport the dishwasher in the  
upright position.  
If unavoidable it may be transported  
on its back.  
Do not transport it on its side or on  
the door. Residual water in the  
machine could leak and cause  
electrical damage.  
42  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
User Maintenance Instructions  
To prevent accidents  
and machine damage,  
read these instructions  
before installation or use.  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Triple filter system  
The triple filter system in the base of the  
wash cabinet prevents food from being  
redeposited on dishes. It also protects  
the circulation pump from damage  
caused by foreign objects (e.g. broken  
glass, bones).  
The filter system should be cleaned  
every 4 - 6 months or whenever a  
foreign object is trapped.  
Cleaning the filter in the wash  
cabinet  
^ Lift the filter out of the machine.  
Remove any solid particles and rinse  
under running water. Scrub with a  
nylon brush if necessary.  
^ Turn off the dishwasher before  
cleaning.  
^ Turn the handle counterclockwise to  
release the triple filter system.  
44  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
To clean the underside of the filter, the  
flap must be opened:  
^ Return the filter so it lies flat in the  
base of the wash cabinet.  
^ Pull back the yellow clip.  
^ Lock the filter by turning the handle  
clockwise.  
^ Rinse all parts under running water.  
Scrub with a nylon brush if  
necessary.  
,The dishwasher must not be  
used without the filter locked in  
place.  
^ Close the flap so that the clip  
engages.  
45  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Cleaning the spray arms  
^ Remove the lower basket.  
Sometimes particles of food get stuck  
in the spray arm jets. The spray arms  
should be inspected and cleaned every  
4 - 6 months.  
^ Turn off the dishwasher before  
cleaning.  
Remove the spray arms as follows:  
^ Remove the cutlery tray (if present).  
^ Press the top spray arm upwards to  
engage the inner ratchet and  
unscrew the spray arm.  
^ Pull the lower spray arm firmly  
upwards to remove.  
^ Lift up the middle spray arm, a, to  
engage the ratchet and unscrew the  
spray arm, b.  
^ Use a pointed object such as a  
toothpick to push food particles into  
the spray arm jets.  
^ Rinse thoroughly under running  
water.  
^ Return the spray arms and check  
that they rotate freely.  
46  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning the wash cabinet  
Cleaning the exterior  
Generally, the wash cabinet is self  
cleaning if the correct amount of  
dishwasher detergent is used.  
,Never use abrasive cleaners,  
scouring pads, steel wool or caustic  
(oven) cleaners on the dishwasher.  
They will damage the surface.  
The wash cabinet can be cleaned with  
a dishwasher cleaner such as Dis  
Cleaner available from your Miele  
dealer or the Miele Technical Service  
Department.  
Plastic  
All plastic surfaces and the control  
panel can be cleaned with warm water  
and liquid dish soap applied with a soft  
sponge.  
Cleaning the door and door  
seal  
Wipe dry using a soft cloth.  
^ Wipe the door seal with a damp cloth  
to remove any food particles.  
,Do not use too much water when  
cleaning the controls. Water could  
penetrate into the electronics and  
cause damage.  
^ Food residue and spilt liquids should  
be wiped from the sides of the  
dishwasher door. These are outside  
of the wash cabinet and are not  
cleaned by water from the spray  
arms.  
Stainless steel  
Stainless steel surfaces can be cleaned  
using a non-abrasive stainless steel  
cleaner.  
To help prevent resoiling, a conditioner  
for stainless steel can also be used.  
Apply sparingly with even pressure.  
Stainless steel colored controls  
These controls may become discolored  
or damaged if not cleaned regularly.  
Do not use a stainless steel cleaner on  
the knobs or buttons.  
Wood  
Panels made from wood should be  
cleaned using a soft damp cloth and an  
appropriate wood cleaner.  
47  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning the water inlet filter  
,The plastic valve housing on the  
intake hose contains electrical  
components and should not be  
immersed, or run through water.  
A filter is incorporated in the intake  
hose attached to the dishwasher’s shut  
off valve. If your water is hard, or the  
pipes contain sediment, this filter may  
clog and prevent enough water from  
entering the wash cabinet.  
Cleaning the filter:  
^ Disconnect the dishwasher from  
electricity (unplug it or "trip" the  
circuit breaker).  
Installing an in-line water filter  
^ If your water contains a large number  
of insoluble substances, a filter  
between the water valve and the  
intake hose connection is  
^ Turn off the water valve.  
^ Unscrew the intake hose.  
recommended. These filters can be  
purchased from Miele’s Technical  
Service Department.  
^ Carefully remove the rubber seal.  
^ Remove the filter using a needle nose  
plier and rinse under running water.  
^ Return the filter and seal. Make sure  
they are seated correctly.  
^ Screw the intake hose back on the  
water valve, checking that it is not  
cross-threaded.  
^ Slowly turn on the valve and test for  
leaks.  
48  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
Cleaning the drain pump and  
non-return valve  
If the dishwasher is not completely  
drained at the end of a program, the  
drain pump or non-return valve may be  
blocked.  
^ Turn off the dishwasher.  
^ Remove the triple filter (see "Cleaning  
the filter in the wash cabinet").  
^ Use a jug or bowl to scoop water out  
of the wash cabinet.  
^ Pull out the non-return valve and  
rinse well under running water.  
^ Tilt the locking clamp to the side.  
The drain pump is beneath the  
non-return valve (see arrow).  
^ Before returning the non-return valve,  
check that the drain pump is not  
blocked. Spin the propeller several  
times in both directions to check for  
obstructions.  
^ Carefully refit the non-return valve  
and secure it with the locking clamp.  
^ Refit and lock the filter in place.  
49  
Download from Www.Somanuals.com. All Manuals Search And Download.  
 
50  
Download from Www.Somanuals.com. All Manuals Search And Download.  
51  
Download from Www.Somanuals.com. All Manuals Search And Download.  
Alterations rights reserved / 0304  
M.-Nr. 05 431 352 / 00  
This bio-friendly paper was bleached without the use of chlorine.  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Miele Cooktop KM 6314 User Manual
Miller Electric Welder ICE 12C User Manual
MTD Blower 692 thru 699 User Manual
MTD Tiller 219 100A User Manual
Nady Systems Microphone DKW1 User Manual
Nady Systems Speaker CX 2314 User Manual
Nokia Stereo System AD 43 User Manual
Onkyo CD Player CR 525 User Manual
Oregon Scientific Home Safety Product THGR 238 NF User Manual
Panasonic Camera Accessories AG HMC153 User Manual