Miele Dishwasher G 5795 User Manual

Operating Instructions

Dishwasher

G 5970

G 5795

en - US, CA

To prevent accidents

and appliance damage

read these instructions

before

installation or use.

M.-Nr. 07 909 280

Download from Www.Somanuals.com. All Manuals Search And Download.

Contents

Additional options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

Delay start . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

BrilliantLight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Settings ^!. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Water hardness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Drying Plus. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Optimize standby. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Refill display. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Check filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51

Reorganize programs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Save options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Keypad tone . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Factory default . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

RemoteVision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56

Frequently asked questions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Technical faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57

Problems water intake/drain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

General problems with the dishwasher . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Sounds. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Poor cleaning results . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Transport . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

User Maintenance Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Cleaning and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Triple filter system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Cleaning the drain pump and non-return valve. . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Installation instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

Help to protect the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78

Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 79

Plumbing. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Connection to the water supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Drainage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

WARNING –

Electrical Safety

Before installation, make sure that

the voltage and frequency listed on the

data plate correspond with the

When using your dishwasher, follow

basic precautions, including the

following:

household electrical supply. This data

must correspond to prevent injury and

machine damage. Consult a qualified

electrician if in doubt.

Read all instructions before

installation or use of the dishwasher

to prevent injury and machine

damage.

Before installation or service,

disconnect the power supply to the

work area by unplugging the unit,

"tripping" the circuit breaker or

removing the fuse.

Use the dishwasher only for its

intended purpose. This appliance is

intended for residential use only.

Do not use an extension cord to

connect this appliance to electricity.

Extension cords do not guarantee the

required safety of the appliance (e.g.

danger of overheating).

Keep these operating instructions in

a safe place and pass them on to

any future user.

Be certain your appliance is

Correct usage

properly installed and grounded by a

qualified technician. To guarantee the

electrical safety of this appliance

continuity must exist between the

appliance and an effective grounding

system. It is imperative that this basic

safety requirement be met. If there is

any doubt, have the electrical system of

the house checked by a qualified

electrician.

The dishwasher is not designed for

commercial use. It is intended for use in

domestic households and in similar

working and residential environments

such as, shops, offices and showrooms

or guest houses.

The dishwasher is not intended for

outdoor use.

It must only be used as a domestic

appliance as specified in these

If the supplied power cord is

damaged it must only be replaced by a

Miele Service technician with a genuine

Miele power cord.

operating instructions, for cleaning

domestic crockery and cutlery. Any

other usage is not supported by the

manufacturer and could be dangerous.

The outlet must be accessible at all

times after installation to disconnect the

Persons who lack physical, sensory

dishwasher.

or mental abilities, or experience with

the appliance should not use the

dishwasher without supervision or

instruction by a responsible person.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Installation

Do not install this dishwasher

beneath a cooking surface, oven or any

The dishwasher must be installed

and connected in accordance with the

installation instructions.

appliance that radiates heat.

High temperatures from these units

may damage the dishwasher.

Installation and repair work should

A toe-kick must be used with the

be performed by a Miele authorized

service technician. Work by unqualified

persons could be dangerous and may

void the warranty.

dishwasher. If the supplied toe-kick is

not used, a cabinet matching toe-kick

must be installed.

Do not install the dishwasher in an

area where it will be exposed to

temperatures below freezing.

Do not install or use a damaged

dishwasher. A damaged appliance is

dangerous. Unplug the machine and

contact the Miele Technical Service

Department.

Do not cut the intake hose or

submerge it in liquid. This hose

contains electrical components that

could cause injury or property damage

if cut or submerged.

Ensure that any plastic wrappings,

bags, etc. are disposed of safely and

kept out of the reach of children.

Danger of suffocation!

Only power up the dishwasher

when all installation and plumbing work

This appliance must not be used in

a non-stationary location (e.g. on a

is complete.

boat).

, WARNING - Fire hazard!

Do not cover or crush the plug of the

appliance. Ensure that the cabinet

opening for the dishwasher provides

ample space for the plug and cord.

Installing the dishwasher in a tight

space may crimp the power cord or put

pressure on the plug which could

cause overheating.

This dishwasher should only be

installed under a continuous counter

top secured to adjacent cabinetry.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

Use

When loading tableware, place

sharp items away from the door to

prevent damage to the seal. Load

sharp items pointing downwards to

prevent injuries.

To reduce the risk of injury, do not

allow children to play in, on or near the

dishwasher. It is possible for small

fingers may be pinched in the door.

Only use detergents and rinse aids

recommended for residential

Only use the dishwasher if all panels

are properly in place.

dishwashers. Keep all detergents and

rinse aids out of the reach of children.

Do not tamper with the controls.

Do not sit or stand on the door or

baskets of the dishwasher. Close the

Do not inhale or swallow detergents.

Dishwasher detergents contain irritant

and corrosive ingredients. They can

cause burning in the mouth and throat if

swallowed, or inhibit breathing. Consult

a doctor immediately if detergent has

been swallowed or inhaled.

door when not in use.

Under certain conditions, hydrogen

gas may be produced in a hot water

system that has not been used for two

weeks or more. HYDROGEN GAS IS

EXPLOSIVE. If the hot water system has

not been used for such a period, turn

on all hot water faucets and let water

flow from each for several minutes

before using the dishwasher. This will

release any accumulated hydrogen

gas. Do not smoke or use an open

flame during this time.

Do not drink water from the

dishwasher! Harmful residues could be

present.

Do not fill the rinse aid reservoir or

salt container with detergent. It will

destroy the rinse aid compartment and

water softener.

If the supplied power cord is

Be sure that all items placed in the

dishwasher are "dishwasher safe". For

items not labeled, check the

damaged it must only be replaced by a

Miele Service technician with a genuine

Miele power cord.

manufacturer’s recommendations.

The outlet must be accessible at all

times after installation to disconnect the

dishwasher.

This model offers a Drying Plus

feature, i.e. the door will automatically

open, without an audible signal first

being given, at the end of the program

releasing warm air from the dishwasher.

Use caution, the air may be hot!

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

This model offers a Drying Plus

feature, i.e. the door will automatically

shut once close enough to engage the

catch.

Advise the user of the Drying Plus

feature to avoid injuries by walking,

bumping or knocking into the partially

opened door.

Supervise children near the

dishwasher to ensure fingers or other

parts of the body are not caught when

the Drying Plus feature is in operation.

Dishes can be very hot at the end of

a program. Allow the dishes to cool

until they are cool enough to handle

before unloading them.

The water supply must be turned off

when the appliance is not used for a

longer period of time (e.g. during

vacations).

Disposal of an appliance

If the appliance is removed from its

installation site and will not be used,

remove the doorlock to the wash

cabinet to prevent children from locking

themselves in the machine.

SAVE THESE

INSTRUCTIONS

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the dishwasher

a Upper spray arm (not visible)

b Cutlery tray

g Triple filter system

h Data plate

c Upper basket

i Optical interface

j Rinse aid reservoir

d Middle spray arm

e Air inlet for drying

(depending on model)

k Dual compartment detergent

dispenser

f Lower spray arm

l Salt container

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the dishwasher

Control panel

aSelection buttons

eK button (Information)

To display more info about the

displayed menu

To select a menu point from this

display, to change the displayed

value (+/-) or to browse between

menus.

f K On/Off button with indicator

To turn the dishwasher on or off.

bDisplay

See the following pages for more

information.

gTechnical Service interface

Allows a service technician to check

and update the machine when

applicable.

cU (Clear) button

To switch back to the previous menu

level or to discard a selected setting.

hOptical interface

To show the current wash cycle

status when the door is closed

dd Delay Start button with indicator

iRemoteVision

Indicator for RemoteVision enabled

appliances.

This operating instruction manual describes several dishwasher models with

different indicated settings.

The different dishwasher models are named :

Standard = 32 ¹/₁₆" (81.5 cm) high dishwashers

XXL

= 33 ¹¹/₁₆" (85.5 cm) high dishwashers.

Download from Www.Somanuals.com. All Manuals Search And Download.

Caring for the environment

Energy saving washing

This dishwasher is exceptionally

economical in the use of water and

electricity. For best results follow these

tips:

^ For lowest energy consumption you

may connect the dishwasher to a

cold water source.

^ For fastest possible wash times, with

slightly higher energy consumption,

connect the dishwasher to a hot

water source.

^ Make full use of the baskets without

overloading for the most economical

washing.

^ Use the correct amount of detergent

and rinse aid. Detergent dosage is

dependent upon the amount of

soiling and type of dishware being

washed. See the "Program Guide" for

more information.

^ When using powder or gel detergent,

reduce the amount to ²/₃of the

normal amount when washing a small

load.

^ Choose a program that best suits the

degree of soiling and the type of

dishes being washed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

To open the door

To close the door

^ Push the baskets in.

^ Lift the door and push until the catch

engages.

The door will then close automatically.

,^{Keep fingers and other body}

parts away from the door as it is

closing. Danger of injury.

The door will open automatically at the

end of the program to aid in the drying

process.

This function can be deactivated (see

"Settings - Drying Plus").

^ Pull the handle to open the door.

If the door is opened during operation,

the rinsing function is automatically

canceled.

,^{Keep the opening area free of}

obstructions.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Display function

The following can be selected in the

display:

A bullet in the display next to the button

shows that this function can be

selected.

– the wash program

– the options

– the start time

– the settings menu ^!

– information

The arrows in the display indicate that

more selections or text follow and can

be displayed with the respective

control.

During a running program the display

shows:

– the program name

– the current time of day

– the program sequence

– the approximate remaining time

– faults and messages

- - - - - -

A dotted line is shown to indicate the

last selection available.

To save energy the dishwasher turns

off after a few minutes if no button is

pressed. To turn the dishwasher

back on press K.

To confirm these messages or settings

select OK, and the next menu or

another menu level will appear.

(

The currently selected option is marked

with a check.

The "Settings !" menu allows you to

customize the dishwasher settings.

See "Settings" for more information.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Welcome screen

^ Turn the dishwasher on K.

A Welcome screen shows when the washer is turned on for

the first time.

Language setting

The display changes automatically to the language setting.

} #eština

} dansk

Sprache F

^ Select the desired language and confirm with OK.

The selected language is marked with a L check.

Clock format

The display changes automatically to the clock format.

} 12 h clock

Clock Format

} 24 h clock B

OK }

^ Select the desired setting and confirm with OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Time of day

The display changes automatically to the time of day setting.

} +

12 : 00

} -

Please set the time of day

OK }

^ Set the hours using the +/- controls and confirm with OK.

Set the minutes and press OK.

Water hardness

The display then changes to the water hardness setting.

} 15°d B

Water hardness

} 16°d

OK }

To achieve good cleaning results, the dishwasher needs soft

water. Hard water results in calcium deposits on dishware

and in the dishwasher.

If your tap water hardness is above 4 °d (4 gr/gal [US]), the

water should be softened.

– Your local water authority will be able to advise you of the

water hardness level in your area.

– The dishwasher must be programmed to correspond to the

water hardness in your area.

– In areas where the water hardness fluctuates (e. g.

37 - 50 °d [39 -52 gr/gal]) always program the machine to

the higher value (in this example 50 °d [52 gr/gal]).

If there is a fault, it will help the service technician to know the

hardness of your local water supply.

Please note your water hardness below:

°d (gr/gal)

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

The water hardness was programmed

at 1 °d (1 gr/gal) by factory default.

Two notes appear in the display.

After confirming these notes, ^:Add

rinse aid and/or : Add salt may

appear in the display.

^ Select the hardness of your water

supply and confirm with the center

button.

Confirm these notes with OK. The

display changes to the main menu.

See "Settings - Water hardness" for

more information.

These basic settings are saved after

the first full program cycle is

completed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

^ Remove the lower basket from the

wash cabinet and unscrew the salt

container lid.

Every dishwasher is tested before

leaving the factory. Any water

remaining in the machine is from the

final factory test and does not

indicate that the machine has been

used.

When opening the salt container,

water will run out. Open the

container only to refill salt.

Filling the salt container

Important: The salt container must

be filled with 2 quarts (2 l) of water

before adding salt for the first time

so the salt can dissolve

To achieve good cleaning results, the

dishwasher needs soft water (water that

is low in minerals). Hard water results in

calcium deposits on dishware and in

the dishwasher.

properly. Water does not have to be

added with subsequent refills.

Therefore, if your tap water hardness is

above 4 °d (4 gr/gal) the water should

be softened. The built-in water softener

is designed for this purpose. The water

softener is suitable for a water hardness

up to 70 °d (73 gr/gal).

,^{Inadvertently filling the salt}

container with dishwashing

detergent (including liquid

detergent) will damage the water

softener.

,^{Only use water softener salt}

specially formulated for

dishwashers. Other salts may

contain insoluble additives which

can impair the water softener.

If using "Tab" products which

include salt, still add salt to the

machine to achieve optimal cleaning

results and ensure long-term

functioning of the water softener.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Salt refill message

^ When the display shows Insufficient

salt, refill the salt after the program

has finished.

^ Confirm with OK.

The message will clear from the display.

If a sufficiently high concentration of

salt has not yet formed, the Insufficient

salt message may continue to be

displayed after adding the salt. In this

case, confirm again with the center

button.

^ Place the provided funnel over the

salt container and carefully fill it with

salt. The salt container holds

The Insufficient salt message is turned

off if you have programmed the

dishwasher to a water hardness below

4 °d (4 gr/gal).

approx. 4.4 lbs (2 kg) of salt,

depending on the type of salt.

^ Clean any excess salt from the

threads of the container opening.

Screw the lid on firmly.

,Immediately after each refill, run

the "Rinse & Hold" program (without

the Turbo function) without a load.

This will remove any traces of salt

from inside the wash cabinet.

^ Immediately after each refill, run the

"Rinse & Hold" program (without the

Turbo function) without a load. This

will remove any traces of salt from

inside the wash cabinet.

If using"Tab" detergent products in

your dishwasher, the messages can

be turned off if desired (see

"Settings - Refill display").

If you switch to using detergent that

does not contain salt or rinse aid, it

is important to remember to

replenish the salt and rinse aid and

to turn the indicators back on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Rinse aid

Rinse aid helps to prevent spotting on

dishes and glassware.

The rinse aid is filled in the reservoir

and the set amount will be

automatically dosed.

,^{Filling the rinse aid reservoir with}

detergent (liquid or powder) will

damage the reservoir. Only pour

rinse aid formulated for residential

dishwashers into the reservoir.

^ Press on the flap until you hear it

click shut. Failure to close it all the

way allows water to enter the

When using "Tab" detergents rinse

aid is not needed.

reservoir during the wash program.

Adding rinse aid

^ Clean any spilled rinse aid. This

prevents over-foaming occurring

during the next program.

You can adjust the rinse aid dosage

for best results (see "Settings - Rinse

aid").

^ Press the button on the rinse aid

reservoir in the direction of the arrow

until the flap springs open.

^ Pour liquid rinse aid into the reservoir

until it is visible on the surface of the

screen.

The rinse aid reservoir holds

approximately 3.7 fl. oz. (110 ml).

Download from Www.Somanuals.com. All Manuals Search And Download.

Before using for the first time

Rinse aid indicator

When the ( Refill rinse aid message

appears, the reservoir contains

sufficient rinse aid for 2 - 3 programs

only.

^ Add rinse aid once the program has

finished.

^ Confirm with the OK button.

The "Refill rinse aid" message will go

out.

If using "Tab" detergent products in

your dishwasher, the messages can

be turned off if desired (see

"Settings - Refill display").

If you switch to using detergent that

does not contain salt or rinse aid, it

is important to remember to

replenish the salt and rinse aid and

to turn the indicators back on.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

^ The spray arms must not be blocked

by items that are too tall or hang

through the baskets. Check

clearance by manually rotating the

spray arms.

,^{Do not wash items soiled with}

ash, sand, wax, grease or paint in

the dishwasher.

Ash and sand do not dissolve and

will be distributed throughout the

inside of the dishwasher.

^ Place very small items in the cutlery

tray or basket so they do not fall to

the bottom of the wash cabinet.

Wax, grease and paint will cause

permanent discoloration and

damage to the dishwasher.

^ Food residue and spilled liquids

should be cleaned from the sides of

the dishwasher door. These are

outside of the wash cabinet and are

not cleaned by water from the spray

arms.

^ Scrape food from dishes before

placing them in the dishwasher,

rinsing is not necessary.

^ Some foods contain natural dyes,

e.g. carrots or tomatoes. Plastic items

may discolor permanently if they

come in contact with food dyes.

^ All items can be placed anywhere in

the baskets.

^ Load dishes so that water can reach

all surfaces. Do not place dishes or

cutlery inside other pieces.

^ Make sure that all items are securely

positioned.

^ Hollow items such as cups and

glasses should be placed upside

down in the baskets.

^ To ensure good water coverage, tall,

narrow and hollow items, i.e. vases

or champagne glasses, should be

placed in the center of the basket

rather than in the corners.

^ Concave based items such as mugs

or bowls, should be placed at an

angle so that water does not pool.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Items not recommended for

dishwashing

Glassware:

– There are no standard guidelines for

washing glassware, when in doubt

wash by hand.

– Cutlery with wooden handles

– Wooden cutting boards

– When purchasing new dishes,

glasses and cutlery, make sure they

are dishwasher safe. Only wash

items marked "dishwasher safe" in

the dishwasher.

– Glued items such as old knives with

handles glued together around the

shank of the blade

– Handmade craft items, antique,

metal trimmed or decorative

glassware

– If fine glassware is washed in the

dishwasher select the "China &

Crystal" program*. This will reduce

the risk of clouding.

– Plastic items that are not heat

resistant

– Copper, brass, tin or aluminum

Silver and aluminum:

– Dishes with color painted over the

glaze. These dishes may fade over

time

– Silver or aluminum items may tarnish.

– Silverware previously cleaned with a

silver polish may be damp or spotted

at the end of a program where water

has adhered to the polish. This can

be rubbed off with a soft, dry cloth.

Silver that has been cleaned in an

immersion dip is usually dry at the

end of a program, but may tarnish.

– Fine glassware and crystal items

should only be washed using the

"China & Crystal" program*.

Otherwise clouding or etching may

occur after frequent washing.

– Cast iron pots and pans

– If left to dry, foods containing sulfur

can discolor silver. These include

egg yolk, onions, mayonnaise,

mustard, fish and marinades.

* depending on model

– Silverware may tarnish or pit if

washed next to stainless steel.

Leave space between these metals.

If unsure whether your china and

crystal are dishwasher safe, please

check with the manufacturer. The

China & Crystal program, although

extremely gentle and thorough can

cause the china and crystal to "wear"

if they are not dishwasher safe.

– Clean aluminum items, e.g. grease

filters, with domestic dishwasher

detergent only.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Typical load for 10 place settings

Upper basket

Lower basket

Cutlery tray

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Typical load for 16 place settings

Upper basket

Lower basket

Cutlery tray

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Upper basket

Foldable spikes

The rows of spikes can be lowered to

make more room for larger items, such

as casserole dishes.

,^{Always use the dishwasher with}

the upper and lower basket inserted

(except during the Tall items

program, if available).

^ Press the yellow lever down a and

fold down the spikes b.

^ Load the upper basket with small,

lightweight, or delicate items such as

cups, saucers, glasses, dessert

bowls, etc.

Hinged cup rack

^ To make room for tall items, raise the

rack upwards.

Shallow pans can also be placed in

the upper basket.

Glasses can be arranged along the cup

rack to give them some support during

the program.

^ Long items such as soup ladles,

mixing spoons and long knives

should be placed lying down across

the front of the upper basket.

^ Lower the cup rack and lean the

glasses against it.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Jumbo cup rack

(depending on model):

Universal support bar

The support bar will hold tall glasses

The cup rack can be set at two different and stem ware securely.

widths so that it can also accommodate

large cups.

^ Fold the bar down and lean the

desired glasses against it.

^ Pull the cup rack upwards and click it

back into position at the required

width.

^ If desired, a section of the cutlery tray

can be removed to allow for even

taller glasses.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Adjusting the height:

You can set the support bar at two

different heights.

^ Pull the support bar upwards and

click it back into position at the

required height.

Use the low setting for small glasses

and tumblers.

Use the high setting for tall glasses and

stem ware.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Adjusting the upper basket

To adjust the upper basket downwards:

In order to gain more space for taller

items the upper basket can be adjusted

on three levels with 2 cm between each

level.

^ Pull up on the levers at the sides of

the upper basket.

^ Adjust the basket to the desired

height and then release the levers to

lock the basket in place.

The upper basket can also be set at an

angle with one side high and the other

side low. Make sure, however, that the

basket can slide smoothly in and out of

the cabinet.

Depending on the setting of the upper

basket, the following plate dimensions

can be accommodated.

Depending on the setting of the upper

basket, a variety of plate dimensions

can be accommodated.

^ Slide out the upper basket.

To adjust the upper basket upwards:

^ Lift the basket up until it clicks into

place.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Lower basket

^ For larger and heavier items such as

plates, serving platters, saucepans,

bowls, etc.

Glasses, cups, small plates and

saucers can also be arranged in the

lower basket.

Dishwasher with cutlery tray

^ Place large platters and dishes in the

center of the lower basket.

When tilted, plates up to 13 3/4"

(35 cm) in diameter can be

accommodated.

Heavily soiled items

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Removable MultiComfort insert

Glass rack

The rear section of the lower basket is

used for cups, glasses, plates, pots

and pans.

^ The glass rack can be raised to make

more room for tall items.

^ Stem glassware, e. g. wine glasses,

champagne flutes or beer glasses,

can be leaned against the glass rack

or suspended from it.

You can remove the MultiComfort insert

to provide more space for larger items

such as pots and pans.

The height of the glass rack is

adjustable.

To remove the insert a

^ Press the yellow handle forwards and

^ Slide the glass rack to the desired

height until the catches click into

place at the top.

remove the insert.

To replace the insert b

^ Slide the hooks of the insert under

the struts of the lower basket.

^ Push down on the insert to snap it

into position.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Universal support bar

Foldable spikes

The support bar will hold tall glasses

and stem-ware securely.

The rows of spikes can be lowered to

make more room for larger items, such

as casserole dishes.

^ Fold the bar down and lean the

desired glasses against it.

^ Press the yellow lever down a and

fold down the spikes b.

^ If desired, a section of the cutlery tray

can be removed to allow for even

taller glasses.

Vase / Bottle insert

The vase / bottle insert can be used to

rinse narrow items, e.g. vases, baby

bottles, etc.

^ Pull the insert up a and bend to the

side b, if not needed.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Cutlery

Split cutlery tray

(depending on model)

Spoons with thick handles may have to

be placed as knives and forks with their

heads in the holders.

^ Arrange the cutlery as shown in the

cutlery tray.

For easier unloading cutlery should be

grouped in zones, one for knives, one

for forks, one for spoons, etc.

Spoon heads should be placed in

contact with at least one of the serrated

retainers on the base of the cutlery tray

to ensure that water runs off them

freely.

The upper spray arm must not be

blocked by tall cutlery items (e.g.

cake servers).

^ You can use the yellow slide to adjust

the height of the middle section of the

cutlery tray to make more room for

large items of cutlery.

The side sections of the tray can be

moved into the middle to accommodate

tall dishware items in the upper basket.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading the dishwasher

Cutlery basket

(depending on model)

^ Fit it onto the cutlery basket if

required.

The cutlery basket can be placed

anywhere on the front rows of spikes in

the lower basket.

^ To avoid risk of injury, knives and

forks should be placed with the

handles upwards in the basket.

However, cutlery placed handle

down in the basket will come out

cleaner and drier.

^ Place small items of cutlery in the

individual slots on three sides of the

cutlery basket.

^ Insert cutlery with the handles facing

downwards, and distribute them

evenly along the insert.

Cutlery insert for the cutlery basket

Use the insert supplied for heavily

soiled items of cutlery.

The insert separates the items so that

they can be reached better by the

spray jets.

Download from Www.Somanuals.com. All Manuals Search And Download.

Optional accessories

Optional dishwasher accessories are available from your Miele dealer, Miele or

Mieleusa.com (depending on your model some may already be supplied with your

machine as standard).

If you would like to...

the following accessory will need

to be ordered...

...wash a Miele Cappuccinatore

...wash additional items of cutlery

...wash long-stemmed glassware

... a Cappuccinatore insert for the

upper basket.

... a cutlery basket for the lower

basket.

... a glassware rack for the lower

basket.

MieleCare Collection

Miele branded cleaning and care products, including dishwasher salt, detergent

and rinse aid, are available to order from your Miele dealer, Miele or the on-line

Miele store www.mieleusa.com

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Detergent

You can use powder, gel or tab

detergents. Follow the dosage

information on the detergent

packaging.

,^{Dishwasher detergents contain}

irritant and corrosive ingredients.

Avoid inhaling or swallowing

dishwasher detergent.

If using a Tab detergent see "Settings -

Deactivate indicators".

Keep children away from detergent.

Keep detergent out of the reach of

children. Keep children away from

the dishwasher when the door is

open. There could still be detergent

residues in the dishwasher. Only

add detergent just before starting

the program and lock the door with

the child safety lock (depending on

model).

Detergent tabs are not recommended

for use with the program "Express"

(depending on model). The tabs may

not dissolve completely.

Dishwasher cleaning products are

available from MIele.

,^{Only use detergents formulated}

for domestic dishwashers.

Use only the recommended amount

of detergent. Continued use of too

much detergent may cause machine

damage.

When using the "China & Crystal"

program (depending on model)

reduce the amount of detergent

used to at least ½ of the normal

dosage. Also make certain your

china and crystal are dishwasher

safe.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Adding detergent

^ Add detergent to the compartments

and close the container flap.

^ Press the latch on the detergent

dispenser. The flap will spring open.

^ Use one tab or add powder or gel

detergent to compartment II and

close the flap.

The flap is always open at the end of a

program.

^ If a Pre-rinse is desired, and

available for your chosen program,

add 1 teaspoon (5 ml) of detergent to

compartment I.

Compartment I holds a maximum of

2 teaspoons (10 ml),

compartment II holds a maximum of

3.5 tablespoons (50 ml) of detergent.

The horizontal marks in compartment II

indicate the levels of approximately 1 ¼

and 2 tablespoons (20 and 30 ml)

respectively. The marks indicate the

approximate fill level in ml when the

door is open in a horizontal position.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Turning on

^ Open the water supply, if closed.

^ Open the door.

^ Make sure the spray arms can rotate freely.

^ Turn the dishwasher on K.

The main menu shows in the display.

If the memory function is selected, the last selected program

is displayed. See "Settings J - Memory".

} Sensor Wash

Main menu

} Express

Selecting a program

Choose your program according to the type of load and

soiling.

The "Program guide" describes the programs and

application.

^ Select the desired program.

The display changes to the program menu.

Sensor Wash

1:32 h

12:00

} Options

Start }

Information about the selected program can be displayed

by pressing the K button.

To choose another program use the U (Clear) button to

return to the main menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Program guide

When to use

Program sequence

Pre-rinse Main

wash

Interim

rinse

Final Drying

rinse

Pots & Pans

For normally soiled pots &

pans with dried on food, and

heavily soiled dishware, use

120% detergent

recommended.

Normal

Program for completely

washing a full load of

required

normally soiled dishware with

the ability to adjust energy and

water consumption based on

the soil load of the dishware.

China & Crystal

For temperature sensitive

glassware and lightly soiled

as required

requ

dishware, use 50% detergent ired

recommended.

SaniWash

Extra Quiet

Rinse & Hold

Express

To sanitize dishware, e.g.

baby bottles, cutting boards

and preparation dishware.

Very quiet program for

normally soiled dishware

with dried on food.

To rinse dishes when a

complete program is not

needed.

"Quick program" for lightly

soiled dishware, e.g. party

dishware or to remove salt

traces from the wash cabinet

after refilling salt; not suitable

for detergent tabs

Heavy Soil

Light

For heavily soiled dishware

with dried starchy food

For lightly soiled dishware,

e.g. party dishware

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Program guide

When to use

Program sequence

Pre-rinse Main

Interim

rinse

Final Drying

wash

rinse

Energy Saver

Sensor Wash

Starch/Cheese

The water intake temperature

must be 115°F (45°C) for light

to normally soiled dishware

Sensor controlled program for

as required

normally soiled dishware

requ

ired

For dishware with dried on

starchy or cheesy food; 120%

detergent recommended

Plastics

To gently clean dishwasher

safe plastics and plastic toys

Tall Items

For extra large, heat resistant

items, e.g. large vases.

Remove upper basket

Glass no rinse aid For a quick cleaning of

cold glassware for direct reuse; use

without detergent and rinse

aid

Glass no rinse aid To wash glassware without

warm

detergent and rinse aid; rinse

cycle with warm water

Usage:

Electric:

Water:

0.01 - 1.3 kWh

1.1 - 5 gal (4 - 19 l)

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Selecting options

Intensive lower basket:

Options can be added to the selected

program.

– For washing heavily soiled dishes in

the lower basket at the same time as

delicate items in the upper basket.

This function will increase the

^ Select the Options menu.

The display shows the available options

for the selected program.

cleaning power in the lower basket in

programs which it is selected.

Depending on the program, the run

time may be extended slightly.

Available options:

Turbo:

Once this function is set for a

program it will remain active for that

program until the setting is changed.

– For shortening the program duration.

To achieve optimum results, energy

consumption rates will increase.

^ Select the desired options.

When the "Turbo" function is used in

correlation with a program a quick

rinse is completed without heating.

The selected options are marked with a

L check.

Use when a complete program is not ^ To de-select an option press the

needed.

respective control again.

Pre-rinse:

^ Confirm the selected options with

OK.

– For easily removable soiling

Soak:

The display changes back to the

program menu. The message Options

selected will appear in this display.

– To soak stubborn soiling.

When using powder detergent, fill

approx. 1 teaspoon (5 g) of

detergent in detergent

compartment I.

Extended drying:

– To enhance drying of odd shaped

dishware and plastic items.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Starting a program

Time display

^ Select Start.

Before the program starts, the time

display shows the running time of the

selected program in hours and minutes.

During the running program the

remaining time is shown in the time

display.

The display shows Close the door.

To select another program or to add

options, select Back and cancel the

program with Cancel.

^ Start the program by closing the

The running time for the same program

may vary depending on the intake

water temperature, load size and

soiling.

door.

The optical interface lights to indicate

that a program is running.

The program starts and "Items can be

added" appears in the display.

As long as this reference is shown,

tableware can be added to the

machine without impairing the cleaning

result.

When a program is selected for the first

time, a time is shown which equals an

average program running time with

cold water.

Each time a program is run, the

electronic adjusts the program running

time according to the intake water

temperature and the load size.

,The water in the dishwasher is

hot, risk of burns by splashing water.

Cancel a program only in the first

few minutes. Otherwise important

program steps (e.g. the water

softening) could be interrupted.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Standby

At the end of a program

A few minutes after the last key is

pressed or at the end of the program

the dishwasher switch into Standby

mode to save energy.

At the end of a program the optical

control light flashes slowly with the door

closed.

The optical function light goes out one

^ To turn the dishwasher back on press hour after the end of a program.

At the end of a program the display

This feature can also be turned off (see shows Program finished or Drying plus

"Settings - Optimize standby"). The

dishwasher will then turn off after

6 hours.

with the door slightly open (if activated).

In the "Express" program, the drying

fan will run for a few minutes after

the program is completed.

If refill salt and/or rinse aid or a fault

are present in the display, the

dishwasher will not turn off.

,^{Dishes tend to chip if removed}

still hot from the dishwasher. If the

automatic door opening setting is

deactivated (see "Settings - Drying

plus") it is recommended to open the

door manually to allow tableware to

cool much faster.

The refill messages can be turned

off when you use a tab detergent

(see "Settings-Refill display").

Fault messages cannot be turned

off.

^ The dishes can now be removed.

Unloading the lower basket first will

prevent water drops from the upper

basket and cutlery tray (depending on

model) from dropping onto dishes in

the lower basket.

^ Push the baskets in.

^ Turn the dishwasher off K.

The dishwasher continues to use

electricity until turned off with the K

button. After a few minutes the

dishwasher will turn off

automatically.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Preparing your appliance for

an extended vacation

Interrupting a program

A program is interrupted as soon as the

door is opened. If the door is closed,

the program will continue from where it

was interrupted.

If you elect to turn off the water to your

home for an extended period of time,

please note that this may not be

enough to reduce the risk of a leak.

,^{Open the door with care. The}

water in the dishwasher is hot.

Danger of scalding. Before closing

the door again, leave it ajar for

approx. 20 secs. This will enable the

temperature in the wash cabinet to

settle. Close the door firmly until it

clicks into place.

To be completely safe, you must

turn off the water supply to each

individual appliance. This means

under the sink for a dishwasher, at

the laundry bib for your washer, etc.

Download from Www.Somanuals.com. All Manuals Search And Download.

Use

Changing a program

If the detergent flap is already open, do not change the

program.

If a program has already started and you wish to change it:

^ Open the door.

Sensor Wash

Main wash

1:32Std

12:00

Cancel }

^ Select Cancel and confirm with OK.

The program is canceled.

Sensor Wash

12:00

Program finished

Main menu }

^ Select Main menu.

The display changes to the main menu.

^ Select the desired program.

^ Select Start.

^ Start the program by closing the door.

The optical interface lights. The program starts.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional options

Delay start

The starting time of a program can be delayed between 15

minutes and 24 hours. The start can be delayed in

15-minute-increments.

When using the "Delay Start" function make sure that the

detergent compartment is dry before adding detergent,

use a cloth if necessary. The detergent might stick

together and not get completely rinsed out.

Do not use liquid detergent when selecting "Delay Start",

the detergent could leak out of the compartment.

,^{It is recommended to add the detergent and lock the}

dishwasher door to prevent children from coming in

contact with the detergent.

^ Open the door.

^ Turn the dishwasher on K.

The K indicator lights.

^ Select the desired program.

^ Select "Delay start,".

The display shows the current time of day and the last

selected Start time, The program end time is also shown.

The indicator , lights.

} +

} -

Start time 12:00

End at 13:32

12:00

OK }

^ Select the desired Start time with the +/- buttons. Holding

the button will automatically increase or decrease the time.

The end time will be automatically adjusted.

^ Confirm with OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional options

The display changes to the program menu.

^ Select Start.

^ Close the door.

The program starts automatically at the selected time.

The indicator , goes out.

A few minutes after the last key press, the dishwasher will

switch into standby mode to save energy. The display and

the indicators will turn off.

Starting a program before the delay start has elapsed:

A program can be started before the delay start time has

elapsed.

^ Open the door.

^ Select Cancel and confirm with OK.

The d indicator lights.

Sensor Wash

12:00

Program finished

Main menu }

^ Select Main menu.

^ Select the desired program.

^ Select Start.

^ To start the program, close the door.

The optical interface lights to indicate that a program is

running.

Download from Www.Somanuals.com. All Manuals Search And Download.

Additional options

BrilliantLight

The dishwasher is equipped with an

interior light. With the door open the

light turns off automatically after

15 minutes

The light can also be turned off.

^ Open and close the door quickly 3

times. The door must be opened

enough so that the interior lighting

turns on then off.

From now on the interior lighting is

turned off.

^ To turn the light on again, repeat the

above process.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

The "Settings J" menu allows you to adjust standard settings

Opening the Settings J menu

^ Turn the dishwasher on K.

The main menu shows in the display.

If the memory function is selected, the last selected program

is displayed. See "Settings J - Memory". Switch to the main

menu by pressing "Clear" U.

} Settings F

Main menu

} Sensor Wash

^ Select "Settings J".

The display changes into the menu "Settings J".

} Language

Language

} Time of day

^ Select the menu option you would like to change.

Press the : button to see more information about the

option currently selected.

The selected options in the submenus are marked with a

check L.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Language J

Time of day

The display contents can be shown in

different languages.

This selection allows the clock to be

shown as 24 or 12 hours. The clock can

also be set from here.

The displayed language can be

changed by the submenu

"Language J".

Setting the clock format

^ Select "Format".

^ Select the desired language and

confirm with OK.

^ Select the desired clock format and

confirm with OK.

The flag behind the word

Language J serves as a guide when

an unfamiliar language is selected.

Select the respective menu with a

flag until the submenu Language J

appears.

Set the time of day

^ Select "Set manually".

^ Set the hour with +/- and confirm

with OK. Set the minutes and confirm.

After confirming the minutes with OK,

the display will revert to the previous

menu.

^ Touch "Clear" to get back into the

Settings J menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Water hardness

°d

gr/gal

Setting in display

Your dishwasher is fitted with a water

softener which you need to program to

the water hardness level in your area,

see "Before the first use".

^ Turn the dishwasher on K.

If the memory function is on, the

program menu instead of the last

selected program will be displayed

(see "Settings - Memory"). If this is the

case use the U button in the main

menu.

37-45

46-60

61-70

38-46

47-62

63-73

^ Select Water hardness from the

"Settings ^!" menu.

The set water hardness is marked

with a check ⁽.

^ Select the water hardness of your

local water supply, confirm with OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Rinse aid

Adjust Sensor Wash

For best results the rinse aid dosage

can be adjusted.

The "Sensor Wash" program can be

adjusted to clean stubborn but normal

soiling.

The dosage can be set between 0 and

6 ml.

^ Select Yes and confirm with OK.

The dosage set by default to 3 ml of

rinse aid per program.

Drying Plus

– Use a higher setting if spots appear

on dry glassware.

To improve the drying process the door

will open (except during the "Extra

Quiet" program) at the end of the

program during the drying phase.

– Use a lower setting if streaking

appears on dishes or glasses.

This feature can be turned off.

^ Selected the desired rinse aid

amount and confirm with OK.

^ Select the desired setting and

confirm with OK.

,^{If you turn the Drying Plus}

function off and still want to open the

door at the end of a program, then

open the door completely.

Otherwise steam can damage the

countertop edges, because the fan

will continue to run.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Optimize standby

Refill display

A few minutes after the last key is

pressed or at the end of the program

the dishwasher will switch into Standby

mode to save energy.

When consistently using multi-function

Tab detergents, you can turn off the

refill displays.

^ Select the desired setting and

This function can also be turned off.

The dishwasher will then turn off

completely after 6 hours.

confirm with OK.

Be sure to turn this setting back on if

you stop using multi-function tab

detergents.

^ Select the desired setting and

confirm with OK.

If refill salt and/or rinse aid or an fault

are present in the display, the

dishwasher will not turn off.

Check filters

This selection allows you to set the

number of programs run before the

filter check message shows.

You can select between 30 and 60

programs.

The refill messages can be turned

off when you use a tab detergent

(see "Settings-Refill display").

Fault messages cannot be turned

off.

The filter check message is set by

default to 50 programs.

^ Select the desired number of

programs and confirm with OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Reorganize programs

The order of the programs in the program list can be

reorganized. The two most frequently used programs can be

saved to the first two positions.

} Sensor Wash B

} Cancel

Select program for position

Continue }

^ Select with e the program which you would like to save to

the first position of the main menu. Confirm the selection

with the button next to the program.

^ Confirm with Continue.

^ Repeat with the second program.

The selected programs are displayed as programmed.

To change a program position, select Back until you reach

the respective program position.

^ When you are done reorganizing the program list, confirm

with Finished.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Save options

Buzzer

Additional options can be selected for

some programs, e.g. extended drying.

See "Use - Selecting options".

When the buzzer is activated, a tone

sounds at the end of a program and if a

fault occurs.

Save options allows you to save the

selected options for future use of the

program.

The buzzer at the end of a program is

turned on by default.

Buzzer at the end of a program

This function is turned off by default.

The buzzer at the end of a program

sounds five times in intervals with a

brief break in between. The buzzer

sounds up to one hour if the

^ Select the desired setting and

confirm with OK.

Temperature

dishwasher in not turned off.

The temperature can be displayed in

"°C/Celsius" or "°F/Fahrenheit".

Buzzer in case of a fault

The buzzer for a fault sounds

The temperatures are shown in

°C/Celsius by default.

continuously. The buzzer sounds up to

two minutes if the dishwasher is not

turned off or the fault is fixed.

^ Select the desired temperature unit

and confirm with OK.

The buzzer for a fault cannot be set

to off.

Buzzer tone

The buzzer volume can be set to 17

different levels.

The buzzer cannot be turned off in

case of a fault.

^ Select the desired volume.

^ Confirm with OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Keypad tone

RemoteVision

A tone will sound when a button is

pressed.

(Optional accessory.

To learn more about RemoteVision

visit www.miele.com.)

The volume can be set to 17 different

levels.

^ Select e to show module state.

^ Select the desired setting and

If "K module connected and ready" is

confirm with OK.

displayed, no further action is required.

Via the "Options" menu you can:

– Reboot the module

Brightness

The display brightness can be adjusted

in 17 levels.

– Reset the factory default settings

– Enter Ad-Hoc mode

^ Select the desired brightness and

confirm with OK.

Refer to the "RemoteVision" section

of this manual or the RemoteVision

Installation manual for further

instructions.

Memory

The memory function allows you to save

the last selected program.

When turning the dishwasher off and on

again after a program has finished or

opening and closing the door, the last

selected program is displayed instead

of the main menu.

The function is turned on by default.

^ Select the desired option and confirm

with OK.

Download from Www.Somanuals.com. All Manuals Search And Download.

Settings

Showroom program

Turning the Showroom program on

^ Select the desired option, confirm

Demo modes are only for

showrooms.

with OK.

^ Confirm the following messages with

The dishwasher has various demo

programs for showrooms.

OK.

^ Press any button to start the selected

The programs "Demo mode" and

"Endless demo mode" show the use

and function range of the dishwasher.

demo mode.

^ To cancel the demo mode press any

button again and confirm with OK.

– Demo mode:

The program is started by pressing

any button. It runs once and must be

started again.

Turning the Showroom program off

^ Select Off to deactivate the

Showroom program and confirm with

OK.

– Endless demo mode:

The program starts as soon as it is

activated and runs in a loop until it is

turned off.

^ Confirm the message Deactivate

demo mode? with OK.

– Demo wash sound:

Factory default

The program activates the pumps to

demonstrate the wash sound.

All settings can be reset to factory

default.

– Trade show mode:

^ Confirm the message Reset to

Once the machine is used for the

first time this option is disabled in the

display.

factory default? with OK.

^ Confirm the information All settings

are reset to factory default with

OK.

– Drying Plus Demo:

The door opens automatically.

Leaving the "Settings J menu"

^ To leave the "Settings J" touch the

"Clear" U control. The main menu

appears.

Download from Www.Somanuals.com. All Manuals Search And Download.

RemoteVision

Miele's RemoteVision Wi-Fi technology

creates a 'virtual link' between your

appliance and our monitoring center. If

a fault occurs, Miele's client service

center will be notified and contact you,

or another trusted individual identified

on your call roster, in order to gain

access to your appliance to fix the

problem.

Be sure your wireless system meets the

following requirements

– A wireless router that supports an

IEEE 802.11b protocol

– Windows XP^®or newer operating

system, Mac^®OS X 10.3 or higher

– Cable or DSL modem

– Microsoft^®Internet Explorer 6 or

higher, Safari 2.0 or higher, Firefox

1.5 or higher

For information on set-up and

installation of the RemoteVision module,

see the separate RemoteVision

installation manual.

* Please note that each wireless router

manufacturer supplies their own

device drivers and setup programs.

Due to the differences in

manufacturers, exact router setup

instructions are not included in this

manual. Wording and instructions

may vary.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

With the aid of the following guide, minor problems can be fixed without a service call.

,^{Repairs should only be carried out by a qualified and trained person in}

accordance with local and national safety regulations. Unauthorized repairs

could cause personal injury or machine damage.

Technical faults

Problem

Possible fault

Solution

The program does not

start.

The door is not properly

closed.

Close the door firmly.

The machine is not

plugged in.

Insert the plug.

The fuse has tripped.

Reset the circuit breaker.

See data plate for

minimum amperage.

The dishwasher is not

turned on.

Press g and select a

program.

No program is selected. Select the desired

program.

Reset the circuit breaker.

The dishwasher stops

during a program.

The fuse has tripped.

See data plate for

minimum amperage.

The optic indicator is

not visible when a

The reflector was not

properly installed.

Install the reflector

properly, see the

Installation diagram.

program has started.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problem

Possible fault

Solution

The optical interface

flashes fast, the buzzer

sounds or the display

shows the fault:

Before trying to remedy the

fault:

– Turn the dishwasher off

with the K button.

; Technical fault FXX

There may be a

technical fault.

After a few seconds:

– Turn the dishwasher on.

– Select the desired

program.

– Close the door.

If the problem persists,

contact Technical Service.

Waterproof fault F70

The waterproof system – Turn off the water supply.

has activated.

Contact Miele Technical Ser-

vice.

Automatic door closing

fault F32

The door may be

blocked.

– Remove the item, if

necessary restart the

program.

If the message shows again

contact Miele Technical Ser-

vice.

Automatic door opening

fault F33

Possible technical fault. – Open the door by hand

and restart the program.

If the message shows again

contact Miele Technical Ser-

vice.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problems water intake/drain

Problem

Possible fault

Solution

The optical interface

flashes fast, the buzzer

sounds and the display

shows the fault:

Water intake fault

The water supply is

closed.

Open the water supply all

the way.

Fault water intake F12/F13

Before fixing the fault:

– Turn the dishwasher off

Fault in the water intake. – Open the water supply all

the way.

– Check and clean the

water intake filter, see

"User Maintenance

Instructions".

– The water pressure at the

water connection is lower

than 4.35 psi. Consult a

plumber.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problem

Possible fault

Solution

The optical interface

flashes fast.

The intake water does

not have a minimum

– Restart the program.

– If the fault is displayed

again, use a different

program.

The program "Energy temperature of 115°F

Saver" displays the

fault:

(45°C). See "Plumbing".

Water intake temp. too

low

The optical interface

flashes fast, the

buzzer sounds and the

display shows the

fault:

Before fixing the fault:

– Turn the dishwasher off

with the K button.

Fault F11:

– Clean the triple filter.

Fault in the water drain.

There might be water in

the wash cabinet.

– Clean the drain pump and

the non-return valve.

Drain fault F11

See "User Maintenance

Instructions" for more

information on the above.

– Remove any kinks in the

drain hose.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

General problems with the dishwasher

Problem

Possible fault

Solution

The display is dark.

The dishwasher has

gone into "Standby"

mode to save energy.

– Turn the dishwasher off

using the K button.

The interior lighting is The interior light was

– Turn the interior light on

(see "Additional options-

BrilliantLight").

not turned on when

the door is opened.

turned off.

The optical function

flashes rapidly.

The middle or lower

spray arm is blocked by

dishware.

– Open the dishwasher door

and rearrange items

The buzzer sounds.

The display shows the

following fault

blocking the spray arms.

The spray arm jets of

the middle or lower

– Turn the dishwasher off K.

Then:

message:

spray arm are clogged.

– Clean the spray arms. See

"User Maintenance

Instructions".

Middle spray arm

blocked

Lower spray arm blocked

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problem

Possible fault

Solution

Detergent is left in the The dispenser was damp Dry the dispenser before

dispenser at the end when detergent was

adding detergent.

of a program.

added.

The detergent lid

cannot be closed

properly.

Detergent residue is

blocking the catch.

Remove the residue.

The door and the

This is not a fault! It is the The moisture will evaporate

interior walls are still normal operating mode of after a short time.

wet after a program

has finished.

the drying system.

Water remains in the

wash cabinet at the

end of a program.

Before fixing the fault:

– Turn the dishwasher off

The triple filter in the wash Clean the triple filter. See

cabinet is clogged.

"User Maintenance

Instructions".

The drain pump or the

non-return valve may be

blocked.

Clean the drain pump and

the non-return valve, see

the "User Maintenance

Instructions".

The drain hose is kinked.

Remove any kinks from the

drain hose.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Sounds

Problem

Possible fault

Solution

There is a knocking

noise in the wash

cabinet

The spray arm is hitting an Interrupt the program,

item in the basket. rearrange items blocking

the spray arms.

Items are not secure in the Interrupt the program, and

There is a rattling

noise in the wash

cabinet

wash cabinet.

rearrange loose pieces.

A foreign object has

become lodged in the

drain pump.

Remove the foreign object

from the drain pump (see

"Cleaning the drain pump

and non-return valve")

There is a knocking

This may be caused by

This has no effect on the

dishwasher. If in doubt,

contact a plumber.

noise in the water line the installation or the

diameter of the pipe.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Poor cleaning results

Problem

Possible fault

Solution

The dishes are not The dishes were not

See "Loading the

dishwasher".

clean.

loaded correctly.

The program was not

powerful enough.

Select a more intensive

program (see "Program

Guide").

Stubborn but normal

Use the function "Adjust

Sensor Wash" (depending on

model, see "Settings").

soiling (e.g. coffee, tea).

Not enough detergent was Use more detergent, or

dispensed.

change the detergent.

The spray arms are

blocked.

Turn the spray arms and

rearrange the dishes if

necessary.

The triple filter in the wash Clean the filter and insert it

cabinet is clogged or not correctly. Clean the spray

correctly inserted. arm jets, if required (see

The spray arm jets might "Cleaning and care").

be clogged as a result.

The non-return valve is

Clean the drain pump and the

stuck open and blocked. non-return valve (see

Wash water will run back "Cleaning and care").

into the wash cabinet.

Glasses and cutlery The rinse aid dosage is

Reduce the dosage (see

"Settings - Rinse aid").

show streaks. The

glasses take on a

bluish shimmer; the

deposits can be

wiped off.

set too high.

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problem

Possible fault

Solution

Dishes are not dry, The rinse aid setting may be Increase the dosage, refill

glasses and

cutlery are

spotted.

too low, or the rinse aid

reservoir is empty.

the reservoir or switch the

rinse aid product when

refilling (see "Rinse aid").

Dishes were taken out too

soon.

Leave dishes in longer (see

"Use").

A "Tab" product was used.

Change the detergent, or

These products have a low refill the rinse aid (see "Rinse

drying effect.

aid").

White residue is

Not enough rinse aid was

Increase the dosage (see

"Setting the rinse aid

dosage").

visible on cutlery used.

and dishes.

Clouding occurs

The salt container is empty. Refill the salt container (see

"Filling the salt container").

on glassware and

cutlery; film can be

wiped off.

The salt container lid was not Reseat it making sure it

screwed on properly.

screws back on correctly.

Unsuitable "Tab" products

were used.

Use a different detergent.

Use normal (powder or gel)

detergent.

The water softener is

programmed on too low a

setting.

Program a higher water

softener setting (see "Water

softener").

Download from Www.Somanuals.com. All Manuals Search And Download.

Frequently asked questions

Problem

Possible fault

Solution

Glasses have a

Detergent deposits.

Change detergent right

away.

brown or blue

discoloration; film

cannot be wiped off.

Glasses are dull and Glasses are not dishwasher There is no remedy.

discolored; film

safe. The surface is

Only use dishwasher safe

glasses.

cannot be wiped off. affected.

Tea or lipstick stains The wash temperature of

Select a program with a

have not been

completely removed. too low.

The detergent has a low

the selected program was higher wash temperature.

Use a different detergent.

bleaching effect.

Plastics are

discolored.

Natural dyes e.g. from

carrots, tomatoes or

Use more detergent (see

"Detergent").

ketchup may be the cause. Discoloration is permanent.

Not enough detergent was

used to break down natural

dyes.

There are rust stains The affected items are not There is no remedy.

on cutlery.

corrosion resistant.

Use only dishwasher safe

cutlery.

No program was run after

refilling salt. Salt residuals

got in the wash cycle.

Start the "Express" program

without a load after refilling

salt (without the "Turbo"

option).

The salt container lid was

not screwed on properly.

Reseat it making sure it

screws back on correctly.

Download from Www.Somanuals.com. All Manuals Search And Download.

After sales service

Repairs

MieleCare

In the event of a fault which you cannot

correct yourself please contact the

Miele Service Department at the phone

number on the back of this booklet.

(USA only)

MieleCare, our Extended Service

Contract program, gives you the

assurance of knowing that your

^ Please quote the model type and

appliance investment is covered by

5 years of worry free ownership.

MieleCare is the only Extended Service

Contract in the industry that guarantees

repairs by a Miele Authorized Service

Provider using genuine Miele parts.

Only genuine Miele parts installed by

factory trained professionals can

guarantee the safety, reliability, and

longevity of your Miele appliance.

number of your appliance.

These can be found on the data plate

along the right edge of the door.

PC Update

The Program Correction (PC) allows a

technician to update the dishwasher to

make use of new technology.

Please note that unless expressly

approved in writing by Miele’s Service

department, Extended Service

Contracts offered by other providers for

Miele products will not be recognized

by Miele. Our goal is to prevent

unauthorized (and untrained) service

personnel from working on your Miele

products, possibly doing further

damage to them, you and/or your

home.

When, for example, technological

developments offer advanced

modifications to your existing program

cycles a service technician will be able

to input these into your machine

controls via the indicator light marked

PC. Miele will provide information when

such possibilities become available.

To learn more about MieleCare

Extended Service Contracts, please

contact your appliance dealer or visit

us online at:

http://mieleusa.com/mielecare

Download from Www.Somanuals.com. All Manuals Search And Download.

Transport

To transport the dishwasher, e.g. when

moving to a new home, note the

following:

– Empty the dishwasher.

– Secure any loose parts, e.g. hoses,

cables, cutlery baskets.

– Transport the dishwasher in the

upright position. If unavoidable it

may be transported on its back. Do

not transport it on its side or on the

door. Residual water in the machine

could leak and cause electrical

damage.

Download from Www.Somanuals.com. All Manuals Search And Download.

User Maintenance Instructions

To prevent accidents

and appliance damage,

read these instructions

before

installation or use.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Exterior

Check and clean your dishwasher

regularly. This will help avoid faults

and problems.

^ Use a conditioner suitable for your

kitchen cabinetry.

^ Clean wood with a damp cloth and

wipe dry.

,^{Abrasive cleaning agents,}

all-purpose cleaners, thinner or

ammonium cleaners should not be

used on the dishwasher.

Clean the exterior with a solution of

warm water and liquid soap applied

with a soft sponge. Dry with a soft

cloth.

They will damage the surface.

Wash cabinet

Glass cleaners may be used to

clean the exterior. However do not

allow them to sit or "puddle", this can

cause damage to the surface.

Remove the cleaner promptly.

Generally, the wash cabinet is self

cleaning if the correct amount of

detergent is used.

The wash cabinet can be cleaned with

a dishwasher cleaner such as "Dis

Cleaner" available from your Miele

dealer or online at www.mieleusa.com.

To better maintain your appliance

avoid the following:

– cleaners containing soda, ammonia,

thinners, or chlorides

Door and the door seal

^ Wipe the door seals regularly with a

– cleaners containing descaling

agents or lime removers,

damp cloth to remove food deposits.

^ Food residue and spilled liquids

should be wiped from the sides of the

dishwasher door. These are outside

of the wash cabinet and are not

cleaned by water from the spray

arms.

– abrasive cleaners,

– stainless steel cleaners,

– dishwasher soap (powder),

– caustic (oven) cleaners,

– scouring pads, steel wool, hard

brushes,

– metal scrapers,

– steam cleaning products.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Indicator reflector

The reflector of the optical interface is

located in the steam deflector beneath

the counter top.

^ Clean as necessary with a damp

cloth.

Control panel

^ Clean the control panel as necessary

with a damp cloth.

,^{The appliance front and controls}

are not scratch proof.

Remove spills immediately.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Triple filter system

Cleaning the triple filter

The triple filter system in the base of the

wash cabinet prevents food from being

redeposited on dishes. It also protects

the circulation pump from damage

caused by foreign objects (e.g. broken

glass, bones, etc.). During normal use,

the filter system is self-cleaning.

,^{The machine must not be used}

without all the filters in place!

^ Check and clean the filter system

periodically for any trapped or

foreign objects.

^ Turn off the dishwasher before

The level of soiling and time it takes

before the filters need cleaning will vary

depending on household.

cleaning.

^ Turn the handle counterclockwise to

release the triple filter system, a.

The display shows Filter check after

^ Remove the triple filter from the

machine. Clean any solid particles

and rinse under running water. Scrub

with a nylon brush if necessary.

50 wash cycles (default setting).

The filter check frequency can be

set from 30 to 60 cycles. See

"Settings J - Filter check".

,^{Be sure that debris does not get}

into the circulation pump causing it

to clog.

^ Check and clean the triple filter.

^ Confirm with OK.

The display changes to the program

menu.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

To clean the underside of the filter the

flap must be opened.

^ Return the filter so it lies flat in the

base of the wash cabinet.

^ Push the clips together a and open

the flap b.

^ Lock the filter by turning the handle

clockwise.

^ Rinse under running water.

,The triple filter system must be

inserted and locked. Large particles

could get in the circulation system

and cause blockage.

^ Close the flap so that the clip

engages.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Cleaning the spray arms

Sometimes particles of food get stuck

in the spray arm jets. The spray arms

should be inspected and cleaned every

4 - 6 months.

^ Turn off the dishwasher before

cleaning.

Removing the spray arms

^ Remove the cutlery tray (if present).

^ Push the upper spray arm up to

engage the inner ratchet and

unscrew the spray arm.

^ Pull the lower spray arm firmly

upwards to remove.

^ Lift up the middle spray arm, a, to

engage the ratchet and unscrew the

spray arm, b.

^ Use a pointed object such as a

toothpick to push food particles into

the spray arm jets.

^ Remove the lower basket.

^ Rinse thoroughly under running

water.

^ Return the spray arms and check that

they rotate freely.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Cleaning the water inlet filter

A filter is incorporated into the intake

hose attached to the dishwasher’s shut

off valve. If your water is hard or the

pipes contain sediment, this filter may

clog and prevent enough water from

entering the wash cabinet.

,^{The plastic housing of the water}

connection contains electrical

wiring.

Do not cut the intake hose or

submerge it in liquid.

^ Carefully remove the rubber seal.

Installing an in-line water filter

^ Remove the filter using needle nose

pliers and rinse it under running

water.

If your water contains a large number of

insoluble substances, a filter between

the water valve and the intake hose

connection is recommended. These

filters can be purchased from Miele.

^ Reinsert the filter and seal. Make sure

they are seated correctly.

^ Screw the intake hose back on the

water valve, checking that it is not

cross-threaded.

Cleaning the filter

^ Turn off the dishwasher and pull the

plug.

^ Slowly turn on the water supply and

^ Turn off the water supply.

test for leaks.

^ Unscrew the intake hose.

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and Care

Cleaning the drain pump and

non-return valve

If the dishwasher is not completely

drained at the end of a program, the

drain pump or non-return valve may be

blocked.

^ Turn off the dishwasher and pull the

plug.

^ Remove the triple filter (see "Triple

filter system").

^ Use a cup or bowl to scoop water out

of the wash cabinet.

The drain pump is beneath the

non-return valve (see arrow).

^ Remove all foreign objects from the

drain pump (glass or bone splinters).

^ Before returning the non-return valve,

check that the drain pump is not

blocked. Spin the propeller several

times in both directions to check for

obstructions.

^ Carefully reinsert the non-return valve

and secure it with the locking clamp.

,^{Make sure the locking clamp}

clicks into place!

^ Tilt the locking clamp to the side a.

^ Pull out the non-return valve b and

rinse it under running water.

^ Remove all foreign objects from the

non-return valve.

Download from Www.Somanuals.com. All Manuals Search And Download.

Installation Instructions

Please refer to the Installation Diagram supplied with these instructions.

To comply with IEC sound testing protocols, please contact Miele for additional

instructions.

Information is subject to change. Please refer to our website to obtain the most

current product specification, technical & warranty information.

Download from Www.Somanuals.com. All Manuals Search And Download.

Help to protect the environment

Disposal of the packing

material

Disposal of an old machine

Old appliances may contain materials

that can be recycled. Please contact

your local recycling authority about the

possibility of recycling these materials.

The cardboard box and packaging

protect the appliance during shipping.

These materials are biodegradable and

recyclable. Please recycle.

Ensure that the appliance presents no

danger to children while being stored

for disposal. Before discarding an old

appliance, unplug it from the outlet, cut

off its power cord and remove any

doors to prevent hazards.

Ensure that any plastic wrappings,

bags etc. are disposed of safely and

kept out of the reach of children.

Danger of suffocation!

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical connection

,^{Installation, repairs and other}

work by unqualified persons could

be dangerous.

,^{Improper connection of the}

equipment grounding conductor

can result in electric shock. Do

not modify the plug provided with

the appliance; if it will not fit the

outlet, have a proper outlet

Check that the voltage, frequency

and fuse rating shown on the data

plate match the household mains

supply.

installed by a qualified electrician.

If there is any question

concerning the proper electrical

connection or grounding of this

appliance to the power supply,

please consult a licensed

The power outlet must be accessible

after installation. Do not use an

extension cord to connect the

dishwasher to the mains. Danger of

overheating! See data plate on the

right side of the door.

electrician or call Miele’s

Technical Service Department:

U 1-800-999-1360

A damaged power cord must only

be replaced with a genuine Miele

cord by a Miele service technician

or a qualified technician.

V 1-800-565-6435

Specifications

The dishwasher comes equipped with a

4 ft (1.2 m) power cord with a molded

plug for connection to 120 V, 60 Hz,

15 A grounded receptacle.

GROUNDING INSTRUCTIONS

THIS APPLIANCE MUST BE

GROUNDED.

In the event of a malfunction or

breakdown, grounding will reduce the

risk of electric shock by providing a

path of least resistance for the electrical

current. This appliance is equipped

with a cord having an equipment

grounding conductor and a grounding

plug. The plug must be plugged into an

appropriate outlet that is installed and

grounded in accordance with all local

codes and ordinances.

Download from Www.Somanuals.com. All Manuals Search And Download.

Electrical connection

Hardwired electrical connection

,^{Prior to making a hardwire}

connection to the terminal, remove

the power cord. Otherwise there will

be a risk of electric shock from the

attached plug.

It is possible to hardwire this appliance

to an existing power cable.

,^{CAUTION: Before servicing,}

disconnect the power supply by

either removing the fuse, shutting off

the power main or manually

An existing flexible supply cord or

cable shall have a minimum thickness

of AWG 14.

"tripping" the circuit breaker.

120 V, 60 Hz, 15 A fuse rating

Installation work and repairs should

only be performed by a qualified

technician in accordance with all

applicable codes and standards.

Repairs and service by unqualified

persons could be dangerous and

the manufacturer cannot be held

responsible.

Black wire (live):

connect to L

White wire (neutral): connect to N

Green wire (ground): connect to -

Before connecting the appliance to

the power supply, make sure that

the voltage and frequency listed on

the data plate correspond with the

household electrical supply. This

data must correspond to prevent

machine damage. Consult an

electrician if in doubt.

GROUNDING INSTRUCTIONS

THIS APPLIANCE MUST BE

GROUNDED.

,^{After attaching the permanent}

power supply cord, check that all

screws on the terminal block and the

strain relief are tightened.

This appliance must be connected to a

grounded metal, permanent wiring

system, or an equipment-grounding

conductor must be run with the circuit

conductors and connected to the

equipment-grounding terminal or lead

on the appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Plumbing

Connection to the water supply

If not connected directly to a water

supply valve, an appropriate

,^{Installation, repairs and other work}

by unqualified persons could be

dangerous.

adapter (not included) is required.

– Water pressure: Must be between

4.5 - 145 psi (0.3 - 10 bar).

,^{Do not drink water from the}

dishwasher!

– If the water pressure if lower, a

"Water Intake" notification will be

shown. See "Frequently Asked

Questions" for more information.

– The dishwasher can heat its own water

to the temperature required by the

wash program. This allows for

connection of the machine to either a

hot (max. 140°F / 60°C) or cold water

source.

– If the water pressure is higher than

shown, a pressure reducing valve

must be used.

Ensure that the water connection is

secure after the first use.

For lowest energy consumption and for

fastest possible wash times connect

the dishwasher to a hot water source.

All programs use hot water in the rinse

cycles.

,^{To prevent damage to the}

dishwasher, it must only be

connected to a fully vented drainage

system.

– To use the "Energy Saver" program, a

hot water connection of minimum

115°F / 45°C and maximum 140°F /

60°C (water intake temperature) is

necessary.

,^{Do not cut the intake hose. If the}

hose is cut, the dishwasher will not

work. There will be a water leak. If

the hose is too long, coil it neatly

and place it behind or under the

machine.

The higher the water intake

temperature, the better the cleaning

and drying results.

– The inlet hose is approximately 5 ft.

(1.5 m) long.

– The water inlet hose comes

equipped with an inlet hose ending

with a 3/8" female compression

fitting. This can be directly

connected to a water supply valve or

to an appropriate coupling.

Download from Www.Somanuals.com. All Manuals Search And Download.

Plumbing

Drainage

– The drain hose must not be

shortened.

– The machine comes equipped with a

built-in non-return valve on the

discharge side to prevent waste

water from flowing back into the

dishwasher.

,^{Make sure the hose is not kinked}

or cut when pushing the machine

under the countertop.

– The dishwasher is equipped with a

5 ft (1.5 m) flexible drain hose with an

internal diameter of 7/8" (22 mm).

Venting the drainage system

If the dishwasher drain hose is

connected to a floor drain or to a drain

pipe that is less than 8" (20 cm) above

the floor, the drain must be vented.

Otherwise the water inside the

dishwasher may siphon out during the

wash program.

– Drain hose extensions and adapters

can be ordered from Miele.

The maximum drain hose length is

13 ft. (4 m), max. drain height: 39"

(1 m).

– Use the clamp provided to attach the ^ Open the dishwasher door and

hose to the dishwashers P trap or

disposal connection (see the

"Installation Diagram").

remove the lower basket.

The hose must always be attached

on the sink side of the P trap.

When attaching the hose to a

garbage disposal fitting, make sure

the plug which is normally blocking

the fitting is knocked out or

removed.

– The hose can be angled to the left or

right side at the rear of the machine.

^ Pull the lower spray arm firmly

upwards to remove.

– The existing nipple that the drain

hose is connected to may be

^ Cut off the vent cap located at the

right rear of the triple filter system, as

illustrated.

designed for various hose diameters.

If the nipple diameter is to large or to

small it should be replaced or an

adapter may be used. If the nipple

extends more than 2" (50 mm) into

the drain hose it should be

shortened, or the hose could clog.

Download from Www.Somanuals.com. All Manuals Search And Download.

Alteration rights reserved / 1511

G5970/G5975 /

M.-Nr. 07 909 280 / 02

INFORMATION IS SUBJECT TO CHANGE. PLEASE REFER TO OUR WEBSITE TO OBTAIN THE MOST

CURRENT PRODUCT SPECIFICATIONS, TECHNICAL & WARRANTY INFORMATION.

Download from Www.Somanuals.com. All Manuals Search And Download.

Multiquip Drums MT75HS User Manual
Multiquip Portable Generator KD1800 User Manual
National Instruments Network Card NI ExpressCard 8360 User Manual
Netopia Network Card 6161210 00 01 User Manual
Nextar GPS Receiver SNAP3 User Manual
Nokia Cell Phone N96 User Manual
N Tron Switch 702 W User Manual
Oreck Vacuum Cleaner BB877 RD User Manual
Oregon Scientific Marine Radio BAR800 User Manual
ParaBody Home Gym PBF501 User Manual