Operating and installation instructions
Gas hobs
KM 2356
KM 2357
en - GB
To avoid the risk of accidents
or damage to the appliance it is
essential to read these
instructions before it is installed
and used for the first time.
M.-Nr. 09 370 470
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas-heated appliances
Safety precautions to take if you smell gas
ß Turn off the gas emergency control valve immediately.
This is usually located near the gas meter.
ß Eliminate all sources of ignition in a safe manner.
Do not smoke, light cigarette lighters or matches.
ß Do not operate electrical lights or switches, i.e. do not switch them "On" or "Off".
ß Open all doors and windows to ventilate the area.
ß If the smell of gas persists, evacuate the building.
In the UK you must now:
ß Call the Gas Emergency Contact Centre (Tel: 0 800 111 999)
For any gas work in the UK always use a Gas Safe registered engineer.
In other countries please follow relevant country specific procedures on gas.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Guide to the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Caring for the environment. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Before using for the first time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Rapid ignition system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Switching on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Regulating the flame . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Switching off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Wok ring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Combi insert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Energy saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Safety features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Thermo-electric ignition safety device. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Safety switch-off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Problem solving guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Safety instructions for installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
KM 2356 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
KM 2357 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Building-in dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Securing the appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
After installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Electrical connection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Gas connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Burner ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Conversion to another type of gas. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Jet table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
To change the main jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
To change the small jets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Function test . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
After sales service, data plate, guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Hob
aSmall burner
Controls:
bLarge burner
gFront left
hBack left
iMiddle
cWok burner
dMedium burner
eMedium burner
fPan support (in three sections)
jBack right
kFront right
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Burners
Wok burner
Small, medium and large burners
aBurner cap
bBurner head
cIgnition safety device
dIgnitor
aOuter burner cap
bInner burner cap
cBurner head
eBurner base
dBurner base
eIgnition safety device
fIgnitor
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Guide to the appliance
Accessories supplied
The accessories supplied with your appliance as well as a
range of optional ones are available to order from Miele (see
"Optional accessories").
Wok ring
The Wok ring supplied with your appliance can be used in
instances where extra stability is required. It is particularly
suitable for Woks with a rounded base.
Combi insert for small pans
For small and large pans, see "Pans".
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
This appliance complies with all relevant local and national safety
requirements. Improper use of the appliance can, however,
present a risk of both personal injury and material damage.
To avoid the risk of accidents and damage to the appliance,
please read these instructions carefully before installation and
using it for the first time. They contain important notes on
installation, safety, operation and care.
Keep these instructions in a safe place and ensure that new users
are familiar with the content. Pass them on to any future owner.
Correct application
This gas hob is not designed for commercial use. It is intended
~
for use in domestic households and similar working and residential
environments.
It is intended for domestic use only to cook food and keep it
warm.
~
Any other usage is not supported by the manufacturer and could be
dangerous. Miele cannot be held liable for damage resulting from
incorrect or improper use or operation.
The gas hob is not intended for outdoor use.
~
The appliance may only be used by people with reduced
~
physical, sensory or mental capabilities, or lack of experience and
knowledge, if they are supervised whilst using it, or have been
shown how to use it in a safe way and understand the hazards
involved.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Safety with children
This appliance is not a toy! To prevent the risk of injury, do not
~
allow children to play with it or use the controls. Please supervise
children whilst you are using the appliance.
Children under 8 years of age must be kept away from the hob
~
unless they are constantly supervised.
Children 8 years and older may only use, clean or maintain the
~
hob without supervision if they have been shown how to do so in a
safe way and understand the hazards involved.
The appliance gets hot when in use and remains hot for quite a
~
while after it has been switched off. Keep children well away from
the appliance until it has cooled down and there is no danger of
burning.
Do not store anything which might arouse a child's interest in
~
storage areas above or next to the hob. Otherwise they could be
tempted into climbing onto the appliance. Danger of burning.
Keep all pans out of reach of children. Turn pan handles inwards
~
away from the edge of the hob. Danger of burning or scalding.
Special hob guards are available from good retail outlets.
Packaging, e.g. polystyrene and plastic wrappings, must be kept
~
out of the reach of babies and young children. Danger of
suffocation. Dispose of or recycle all packaging safely as soon as
possible.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
Before installation, check the appliance for visible signs of
~
damage. Do not install and use a damaged appliance. It could be
dangerous.
The electrical safety of this appliance can only be guaranteed if
~
correctly earthed. It is most important that this basic safety
requirement is observed and tested regularly, and where there is
any doubt, the household wiring system should be inspected by a
qualified electrician. Miele cannot be held liable for the
consequences of an inadequate earthing system (e.g. electric
shock).
Before connecting the appliance to the mains electricity supply,
~
make sure that the data quoted on the data plate match the
household mains supply, otherwise the appliance could be
damaged. Consult a qualified electrician if in any doubt.
For safety reasons, this appliance may only be used when it has
~
been built in.
Connection to the gas supply must be carried out by a suitably
~
qualified and competent person in strict accordance with current
local and national safety regulations, e.g. a Gas Safe registered
technician in the U.K.
If the appliance is supplied without a plug, or if the plug is removed,
it must be connected to the mains electricity supply by a suitably
qualified and competent electrician in strict accordance with current
local and national safety regulations. The manufacturer cannot be
held liable for damage caused by incorrect installation or
connection.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Never open the outer casing of the appliance. Tampering with
~
electrical connections or components and mechanical parts is
highly dangerous to the user and can cause operational faults.
Installation, maintenance and repairs may only be carried out by
a suitably qualified and competent person in strict accordance with
current national and local safety regulations.
~
Repairs and other work by unqualified persons could be dangerous.
Miele cannot be held liable for unauthorised work.
During installation, maintenance and repair work, the appliance
~
must be disconnected from the gas supply and mains electricity
supply.
While the appliance is under guarantee, repairs should only be
~
undertaken by a service technician authorised by Miele. Otherwise
the guarantee is invalidated.
Faulty components must only be replaced by genuine Miele
~
original spare parts. The manufacturer can only guarantee the safety
of the appliance when Miele replacement parts are used.
The appliance is not intended for use with an external timer
~
switch or a remote control system.
If the connection cable is damaged, it must be replaced by a
~
suitably qualified electrician with a special connection cable of type
H 05 V V-F (pvc insulated), available from the Miele Spare Parts
Department.
Do not connect the appliance to the mains electricity supply by a
~
multi-socket adapter or an extension lead. These do not guarantee
the required safety of the appliance (e.g. danger of overheating).
Do not use the hob if it is faulty. Switch it off immediately and
~
disconnect it from the mains electricity supply and the gas supply.
Call Miele Service.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
In areas which may be subject to infestation by cockroaches or
~
other vermin, pay particular attention to keeping the appliance and
its surroundings in a clean condition at all times. Any damage which
may be caused by cockroaches or other vermin will not be covered
by the guarantee.
Correct use
The appliance gets hot when in use and remains hot for quite a
~
while after it has been switched off. Do not touch it whilst it could still
be hot.
If a cooker hood is installed above the gas hob, ensure that the
~
burners are always covered with a pan when in use. Otherwise
flames could reach the cooker hood, parts of which could then be
damaged or set on fire.
Do not leave the appliance unattended whilst it is being used. Oil
~
and fat are potential fire hazards as they can ignite if overheated.
If oil or fat does catch fire, do not attempt to put out the flames
~
with water. Use a suitable fire blanket, saucepan lid, damp towel or
similar to smother the flames.
Do not use the appliance to heat up the room. Due to the high
~
temperatures radiated, objects near the appliance could catch fire.
The life of the appliance could also be reduced.
Do not flambé under a cooker hood. The flames could set the
~
cooker hood on fire.
Always use heat-resistant pot holders or gloves when working
~
with a hot appliance. Ensure that they do not come into contact with
the flames. Do not use large cloths, tea towels or similar as the ends
could touch the flames and catch fire. Take care not to let the gloves
get damp or wet, as this causes heat to transfer through the material
more quickly with the risk of scalding or burning yourself.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Do not use the appliance as a resting place for anything else. The
~
article could melt or catch fire if residual heat is still present or if the
appliance is switched on by mistake.
Do not cover the hob with, e. g. with a hob cover, a cloth or
~
protective foil. This could present a fire hazard if the appliance is
switched on by mistake or if it is still warm.
Do not use plastic or aluminium foil containers as these melt at
~
high temperatures and could catch fire.
Do not heat up unopened tins of food on the hob as pressure will
~
build up in the tin, causing it to explode. This could result in injury
and scalding or damage.
Make sure all the components of the gas burners have been
~
correctly assembled before switching on.
Pans must be the correct size for the burner they are used on
~
(see "Suitable pans"). A pan which is too small will be unstable on
the pan support. If the pan diameter is too large, flames can spread
out to the sides and damage or burn the worktop, wall claddings or
surrounding units and also parts of the hob. Miele cannot be held
liable for this type of damage.
Ensure that the flames from the burner do not spread out beyond
~
the base and up the sides of the pan.
Unless the pan manufacturer states that you can do so, do not
~
use pans with very thin bases on this hob, and never heat up empty
pans as they could get damaged. This could also damage the
appliance.
The pan support supplied must always be used. Pans must not
~
be placed directly on the burner.
Do not store any inflammable objects near the gas hob.
~
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Remove splashes of fat and other food debris from the surface as
~
soon as possible. These are a fire hazard.
Replace the pan supports carefully to avoid scratching the
~
surface of the hob.
Using a gas hob results in the build-up of heat, moisture and
~
combustion products in the room in which it is installed. To ensure
that there is adequate ventilation, especially when the appliance is
in use: make sure natural ventilation to the room is unhindered or
use a mechanical ventilation device (e.g. a cooker hood).
Intensive and prolonged use of the appliance may result in a
~
requirement for additional ventilation, e.g. opening a window or a
more effective form of ventilation, e.g. use of a cooker hood on a
higher setting.
When using the gas hob an extractor hood or a ventilation facility
~
must be used.
When using an electrical appliance, e.g. a hand-held food
~
blender, near the gas hob, ensure that the cable of the electrical
appliance does not come into contact with the hot appliance. The
insulation on the cable could become damaged, giving rise to an
electric shock hazard.
Spray canisters, aerosols and other inflammable substances must
~
not be stored in a drawer under the hob. Cutlery inserts must be
heat-resistant.
Do not use pans that are large enough to cover more than one
~
burner. The resulting build-up of heat could damage the appliance.
Avoid allowing liquids or foods containing salt to spill onto the
~
hob. If salty foods or liquids do get on the hob, they should be
removed as soon as possible to avoid the risk of corrosion.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
If the appliance is installed behind a kitchen furniture door, it may
only be used with the furniture door open.
~
Only close the door if the appliance is switched off.
If the appliance has not been used for a long period of time it
~
should be thoroughly cleaned before it is used again. It is also
advisable to have the appliance tested for safety.
Miele cannot be held liable for damage caused by
non-compliance with these Warning and Safety instructions.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
material
Disposal of your old appliance
Electrical and electronic appliances
often contain materials which, if
handled or disposed of incorrectly
could be potentially hazardous to
human health and to the environment.
They are, however, essential for the
correct functioning of your appliance.
Please do not therefore dispose of it
with your household waste.
The transport and protective packing
has been selected from materials which
are environmentally friendly for
disposal, and should be recycled.
Ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of babies and
young children. Danger of suffocation.
Please dispose of it at your local
community waste collection/recycling
centre or contact your dealer for
advice. Ensure that it presents no
danger to children while being stored
for disposal.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Before using for the first time
Please stick the extra data plate for the appliance supplied
with this documentation in the space provided in the "After
sales service, data plate" section of this booklet.
Cleaning for the first time
^ Remove any protective foil.
^ Clean all removable parts of the burners with a solution of
warm water and a little washing-up liquid applied with a
soft sponge. Dry all parts thoroughly after cleaning and
then reassemble the burners (see "Cleaning and care").
^ Before using for the first time, clean the appliance with a
damp cloth only and then wipe dry.
The metal components have a protective coating which may
give off a slight smell when heated up for the first time.
The smell and any vapours given off do not indicate a faulty
connection or appliance, and they are not harmful to health.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Rapid ignition system
The appliance has a rapid ignition system with the following
features:
– Rapid ignition without pressing and holding the control dial
– Automatic reignition
If the flame is extinguished by a draught, etc. the burner is
automatically reignited. If reignition is unsuccessful, the
gas supply is automatically cut off (see "Thermoelectric
ignition safety device")
Controls
The control is used to ignite the burner and to regulate the
strength of the flame.
Small, medium and large burners
ß The gas supply is turned off
& Strongest flame
/ Weakest flame
Wok burner
ß The gas supply is turned off
& Strongest flame:
The inner and outer burners operate at the highest setting.
& Strong flame:
The outer burner operates at the lowest setting,
the inner burner at the highest setting
/ Weak flame:
The outer burner is switched off,
the inner burner operates at the highest settling
/ Weakest flame:
The outer burner is switched off,
the inner burner operates at the lowest setting
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Switching on
When using the gas hob an extractor hood or a ventilation
facility must be used.
^ The control for the burner required must be pressed in and
turned anti-clockwise to the largest flame symbol to switch
on. The ignitor will make a clicking sound and ignite the
gas.
When a control is operated, a spark is produced on all
cooking zones. This is not a fault.
If the burner does not ignite, turn the control to off "ß ". Air the
room or wait at least 1 minute before trying again.
If the burner does not ignite the second time, turn the control
to "ß ", and see "Problem solving guide".
When switching on, re-ignition sometimes occurs (1-2 clicks)
if the flame on the ignition safety device has gone out briefly,
or if the thermal element is not hot enough, e.g. following a
gust of air.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Regulating the flame
Regulate the flame so that it does not spread out beyond the
sides of the pan. As the outer part of the flame is much hotter
than the centre, the tips of the flames should stay beneath the
pan base. Flame tips which extend beyond the sides of the
pan merely warm up the air in the room and can also damage
pan handles and increase the risk of injury.
The burners can be regulated at any level between the
strongest and weakest flame. Exception: The wok burner
On the wok burner there is a stopper at the 6 o'clock position
to prevent you turning the control to the high or low setting
unintentionally. To move from the high to the low setting, you
need to press the control down to be able to pass the 6
o'clock position.
^ To move from the high to the low setting, turn the control
anti-clockwise until it stops. Then press it down and
continue to turn it past the resistance before releasing it.
You can now select the setting you require.
^ To move from the low to the high setting, turn the control
clockwise until it meets a resistance. Then press it down
and continue to turn it past the resistance before releasing
it. You can now select the setting you require.
Switching off
^ Turn the control clockwise to position "ß ".
This stops the flow of gas and the flame goes out.
Do not turn the control past the "ß " position.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Pans
Burner
Min. pan base diameter in cm
Small
Medium
Large
Wok
10
10
12
15
Max. diameter at top of pan in cm
Without
With
Combi insert
Small
Medium
Large
Wok
22
22
24
26
-
-
-
30
– Refer to the chart above and ensure that the pan diameter
falls within the minimum and maximum diameters given for
the burner you are using. A pan which is too small will be
unstable on the pan support. If the pan base diameter is
too large, flames can spread out to the sides and damage
or burn the worktop, wall claddings or surrounding units
and also parts of the hob. The manufacturer cannot be
held liable for this type of damage.
– Remember when purchasing new pans that manufacturers
usually refer to the diameter at the top of the pan in their
documentation.
– Any heat-resistant pans can be used.
– Pans with thick bases are preferable as these distribute
heat more evenly. With thin bases, there is a danger of
food overheating in places. Stir the food frequently.
– Always place pans on the pan support supplied. Pans
must not be placed directly on the burner.
– Place pans securely on the pan rest to minimise the risk of
tipping.
– Do not use pots or pans with bases with pronounced
edges or or ridges, e.g. cast iron pans.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Pans
Wok ring
The Wok ring supplied with your appliance can be used in
instances where extra stability is required. It is particularly
suitable for Woks with a rounded base.
Make sure that the wok ring is located securely in its correct
position.
Combi insert
The combi insert must be used if you wish to use
– a pan with a smaller diameter base than the minimum
given in the table. The ring ensures that the pan will sit
securely on the hob, and prevents it from tipping.
– a large pan. The combi insert will prevent damage to the
worktop, and the stainless steel trough from becoming
discoloured. Refer to the information given in the table.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Energy saving tips
– Use a pan lid whenever possible to minimise heat loss.
– Cook with as little water as possible.
– Cooking times are greatly reduced when using a pressure
cooker.
– Turn the flame down promptly to a lower setting when the
pan has come to the boil.
– Wide, shallow pans are preferable to tall, narrow ones.
They will heat up faster.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety features
Thermo-electric ignition safety device
This appliance is has a thermo-electric ignition safety device.
If the flame goes out, for example if food has boiled over or if
there is a sudden draught, and automatic re-ignition has
been unsuccessful, the supply of gas to the burner will be cut
off preventing any further escape of gas.
^ To use the burner again, turn the control clockwise to the
"ß " position, and then switch it back on as normal.
Safety switch-off
If a burner has been used for an unusually long period
(approx. 4 hours), it will switch off automatically.
^ To use the burner again, turn the control clockwise to the
"ß " position, and then switch it back on as normal.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
,Do not use a steam cleaning appliance to clean this
appliance. The steam could reach electrical components
and cause a short circuit.
– The appliance should be cleaned after each use. Allow the
appliance to cool down to a safe temperature before
cleaning.
– To avoid water marks and limescale deposits, use a soft
cloth to dry surfaces that have been cleaned with water.
– Stubborn soiling should be soaked first.
– Remove any soiling immediately. Food which boils over
onto the hot hob can cause the burner components and
the stainless steel surface of the hob to discolour.
– The surfaces of the burner components will become more
matt with time. This is quite normal and will not affect the
operation of the hob.
To avoid damaging the surface of your appliance, do not use:
– cleaning agents containing soda, alkalines, ammonia,
acids or chlorides,
– cleaning agents containing descaling agents,
– stain or rust removers,
– abrasive cleaning agents, e.g. powder cleaners and cream
cleaners,
– solvent-based cleaning agents,
– dishwasher cleaner,
– grill and oven cleaners,
– glass cleaning agents,
– hard, abrasive brushes or sponges, e.g. pot scourers, or
sponges which have been previously used with abrasive
cleaning agents,
– sharp pointed objects
(these can damage the seal between the frame and the
worktop)
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning
Notes
Clean stainless steel surfaces using an E-Cloth Printed surfaces
(see "Optional accessories") or with a solution (Flame symbols)
of warm water and a little washing-up liquid Remove any soiling which
applied with a soft sponge. comes into contact with the
If necessary, you could use Miele ceramic and printed flame symbols
Stainless steel
surfaces
stainless steel hob cleaner (see "Optional
accessories") and the scouring pad on the
reverse of a washing-up sponge. Apply with
straight away. Soiling,
particularly salty food or
liquid and olive oil, can cause
an even pressure following the direction of the damage if left on the printed
"grain".
surfaces for a long time.
Do not use stainless steel
cleaning agents on the
printed flame symbols. This
would rub off the print.
Miele conditioning agent for stainless steel can
be used after cleaning to help prevent
re-soiling (see "Optional accessories"). Follow
the instructions on the packaging.
Remove the pan supports.
Pan supports
Wash them in the dishwasher or with a
sponge and warm water with a little
washing-up liquid. If necessary, you could use
the scouring pad on the reverse of a
washing-up sponge.
Clean the controls with a solution of warm
water and a little washing-up liquid applied
with a soft sponge.
Not dishwasher proof.
Not dishwasher proof.
Controls
Clean the burner caps using an E-Cloth (see
"Optional accessories") or with a solution of
warm water and a little washing-up liquid
applied with a soft sponge.
Burner cap
If necessary, you could use the scouring pad
on the reverse of a washing-up sponge.
Clean the burner heads using an E-Cloth (see Not dishwasher proof.
"Optional accessories") or with a solution of
warm water and a little washing-up liquid
Burner head
Make sure that the flame slits
applied with a soft sponge.
are completely dry after
If necessary, you could use the scouring pad
on the reverse of a washing-up sponge.
cleaning.
The ignitors and ignition safety devices should Do not let the ignitors get
be very carefully wiped clean using a well
wrung out cloth.
Ignitor
wet. If they get wet they will
not spark.
Ignition safety
device
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
To assemble the small, medium and large burners
^ Place the burner head b on to the burner base e so that
the ignition safety device d and the ignitor c extend
through their respective holes in the burner head. The
burner head must click into place correctly.
^ Place burner cap a flat over burner head b.
When correctly positioned it will not slide about.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
To assemble the wok burner
^ Place burner head c onto burner base d so that the
ignition safety device e and the ignitor f extend through
their respective holes in the burner head. The burner head
must click into place correctly.
^ Place the burner caps a and b in position.
^ Important: replace parts in the correct order after cleaning.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes, minor faults in the performance of the
appliance, some of which may result from incorrect operation can be put right
without contacting the Service Department saving you both time and money.
The following guide may help you to find the reason for a fault, and to correct it.
You should, however, note the following:
,Repairs to the gas and electrical components of this appliance must only
be carried out by a suitably qualified and competent person to ensure safety
(Gas Safe registered in the UK). Repairs and other work by unqualified persons
could be dangerous. The manufacturer cannot be held liable for unauthorised
work.
Problem
Possible cause
Remedy
The burner does not ignite There could be an air
You may need to make several attempts before
the burner ignites successfully.
when the hob is being
used for the first time or
after a long period of not
being used.
lock in the gas pipe.
Repeat the ignition process as necessary.
Allow a minimum interval of 1 minute between
each ignition attempt to prevent a build-up of
unburnt gas.
The burner does not ignite
after several attempts.
Turn all the controls clockwise to the "ß "
position and disconnect the appliance from the
electricity supply for a few seconds.
The burner is not
correctly assembled.
Assemble the burner correctly.
Turn on the gas supply tap.
Clean and dry the burner.
Clean and dry the flame slits.
The gas supply tap is
turned off.
The burner is wet or
dirty.
The flame slits are
blocked and/or wet
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
If there is a power cut
during operation
Turn all the controls clockwise to the "ß "
position. You can then operate the appliance
as normal when power is restored.
The gas flame goes out
after ignition
The flames are not
touching the ignition safety
device, it is not hot
enough:
Assemble the burner correctly.
Remove any soiling.
- The burner is not
correctly assembled.
- There is dirt on the
ignition safety device.
The flame pattern has
changed
The burner is not correctly Assemble the burner correctly.
assembled.
The burner head or burner Remove any soiling.
cap holes are dirty.
The flame goes out
during operation
The burner is not correctly Assemble the burner correctly.
assembled.
The ignitor on the burner Check whether the mains If it has, contact a qualified electrician or
does not spark.
fuse has tripped.
Miele Service.
- Food residues between
Remove any soiling. Please see "Cleaning
the ignitor and the burner and care" for details.
cap.
- Food residues on the
ignition safety device
Power cut.
Turn all the controls clockwise to the "ß "
position. You can then operate the appliance
as normal when power is restored.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Optional accessories
Miele offer a comprehensive range of useful accessories as
well as cleaning and conditioning products for your
appliance.
These products can be ordered online at:
or from Miele (see back cover for contact details)
Cleaning products
Ceramic and stainless steel hob cleaner
250 ml
Removes heavy soiling, limescale deposits and light
discolouration
Stainless steel conditioning agent
250 ml
Removes water marks, flecks and finger prints.
Helps prevent re-soiling.
E-cloth (microfibre cloth)
Removes finger marks and light soiling.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Do not use any sealant except
~
Fit the wall units and extractor hood
before fitting the appliance to avoid
damaging the surface.
where expressly instructed to do so.
The seal underneath the appliance
provides a sufficient seal for the
worktop.
The veneer or laminate coatings of
worktops (or adjacent kitchen units)
must be treated with 100°C
heat-resistant adhesive which will not
dissolve or distort. Any backmoulds
must be of heat-resistant material.
~
All dimensions in this instruction booklet
are given in mm.
Installation area
This appliance must not be used in
~
a non-stationary location (e.g. on a
ship).
The room in which the hob is to be
located must have
– a minimum capacity of 25.2 m3.
An electric fryer must not be
~
– At least one externally-opening door
or window
installed directly next to a gas hob, as
the gas flames could ignite the fat in the
fryer. It is essential to maintain a
distance of at least 300 mm between
these two appliances.
– An extractor hood or a controlled
ventilation system (not recirculation),
which has a minimum capacity of
189 m3/h
A gas hob may not be built in over a
~
fridge, fridge freezer, freezer,
dishwasher, washing machine or
tumble dryer.
– appropriate air inlets.
Ensure that the gas pipe and
~
electrical cable are installed in such a
way that they do not touch any parts of
the appliance which become hot. This
could cause damage.
The electrical cable (and a flexible
~
gas connection pipe in countries where
applicable) must be installed in such a
way so that they do not come into
contact with any moving kitchen parts
(e.g. a drawer), and cannot become
trapped.
Observe carefully the safety
~
distances given on the following pages.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distance above the hob
When two or more appliances are
installed together below a cooker
hood, e.g. a gas hob and an
induction hob combiset, which have
different safety distances given in
the installation instructions, you
should select the greater distance of
the two.
A minimum safety distance must be
maintained between the hob and the
cooker hood above it. See the cooker
hood manufacturer's operating and
installation instructions for details.
If the manufacturer's instructions are
not available for the cooker hood, a
minimum safety distance of at least
760 mm must be maintained.
For any flammable objects, e.g. utensil
rails, wall units etc. a minimum distance
of at least 760 mm must be maintained
between them and the hob below.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety instructions for installation
Safety distances to the sides and
back of the hob
Ideally the hob should be installed with
plenty of space on either side. There
may be a wall at the rear and a tall unit
or wall on one side (right or left) (see
illustrations).
Not allowed
aMinimum distance of 50 mm
between the back of the worktop
cut-out and the rear edge of the
worktop.
bMinimum distance of 150 mm
between the right of the worktop
cut-out and the nearest piece of
furniture (e.g. tall unit) or a wall.
cMinimum distance of 150 mm
between the left of the worktop
cut-out and the nearest piece of
furniture (e.g. tall unit) or a wall.
Recommended
Not recommended
Not recommended
35
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2356
Building-in dimensions
aFront
bCasing depth
cGas connection R 1/2 - ISO 7-1 (DIN 10226)
dMains connection box with mains connection cable, L = 2,000mm
eElectronics housing
Max. building-in depth 101 mm
36
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2356
Installation
^ Make the worktop cut-out as shown
in "Building-in dimensions".
Remember to maintain the minimum
safety distances (see "Safety
instructions for installation").
^ Seal the cut surfaces on
wood/laminated worktops with a
suitable heat-resistant sealant to
avoid swelling caused by moisture.
Make sure that the sealant does not
come into contact with the top of the
worktop.
^ Feed the connection cable down
through the cut-out.
^ Place the hob in the cut-out without
securing it.
If the corners of the frame are not
flush with the worktop surface, the
corner radius (ß R4) can be carefully
scribed to fit.
^ Connect the hob to the mains (see
"Electrical connection").
^ Connect the appliance to the gas
supply (see "Gas connection").
^ Secure the appliance at the back and
front using the fixings supplied. See
"Securing the appliance".
37
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2356
Seal between appliance and
worktop
Tiled worktop
Grout lines a and the hatched area
underneath the hob frame must be
smooth and even. If they are not the
hob will not sit flush with the worktop
and the sealing strip underneath the
hob will not provide a good seal
between the hob and the worktop.
The sealing strip under the edge of the
top part of the appliance provides a
sufficient seal for the worktop.
The appliance must not be sealed
with sealant (e.g. silicone).
This could result in damage to the
appliance or the worktop if the
appliance ever needs to be
removed for servicing.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2357
Building-in dimensions
aFront
Please take careful note of the
bCasing depth
detailed diagrams for the cut-out
dimensions in granite and marble
worktops.
cGas connection
R 1/2 - ISO 7-1 (DIN EN 10226)
dElectrical connection cable
eElectronics housing
Max. building-in depth 101 mm
fStepped cut-out for granite or marble
worktops
39
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2357
Flush fit gas hobs are only suitable
for installation in granite, marble,
tiled or solid wood worktops. When
using a worktop made from any
other material, please check first
with the worktop manufacturer that it
is suitable for installing a flush fit
hob.
This appliance requires a 900 mm
wide base unit for installation.
The hob must be accessible from
below for servicing purposes and to
ensure that the seal around it is not
dislodged.
The hob may be fitted
– in a suitable cut-out in a granite or
marble worktop.
– in a suitable cut-out in a tiled or solid
wood worktop with a wooden support
frame. The frame must be provided
on site, and is not supplied with the
appliance.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2357
Installation
^ Make the worktop cut-out as shown
in "Building-in dimensions".
Granite and marble worktops
Remember to maintain the minimum
safety distances (see "Safety
instructions for installation").
^ Feed the connection cable down
through the cut-out.
^ Centre the hob b in the cut-out.
^ Connect the hob to the mains (see
"Electrical connection").
^ Connect the appliance to the gas
supply (see "Gas connection").
^ Secure the appliance at the back and
front using the fixings supplied. See
"Securing the appliance".
aWorktop
bHob
cGap
^ Check that the hob works.
^ Seal the remaining gap c with a
silicone sealant that is heat-resistant
to at least 160 °C.
As the ceramic glass and the
worktop cut-out have a certain
dimensional tolerance, the size of
gap c can vary.
For granite and marble worktops,
only use silicone sealant that is
especially formulated for granite and
marble, and observe the sealant
manufacturer's instructions.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2357
Solid wood and tiled worktops
^ Make the worktop cut-out as shown
in "Building-in dimensions".
Remember to maintain the minimum
safety distances (see "Safety
instructions for installation").
^ Fix the wooden frame d 2 mm
below the top edge of the worktop
(see diagram).
^ Feed the connection cable down
through the cut-out.
^ Centre the hob b in the cut-out.
^ Connect the hob to the mains (see
"Electrical connection").
aWorktop
bHob
^ Connect the appliance to the gas
supply (see "Gas connection").
cGap
dWooden frame 7 mm
(to be provided on site)
^ Secure the appliance at the back and
front using the fixings supplied. See
"Securing the appliance".
As the ceramic glass and the
worktop cut-out have a certain
dimensional tolerance, the size of
gap c can vary.
^ Check that the hob works.
^ Seal the remaining gap c with a
silicone sealant that is heat-resistant
to at least 160 °C.
Please follow the manufacturer's
instructions.
For granite and marble tiles only
use a silicone sealant that is
specifically formulated for granite
and marble, and observe the sealant
manufacturer's instructions.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
KM 2357
Building into a stainless steel worktop
This appliance can be welded into a stainless steel worktop. It is essential that
after being welded, it is still recognisable as a Miele appliance.
,Welding must be carried out by a trained, Miele-approved person.
aStainless steel worktop
bLasered edge
cWelded edge
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Securing the appliance
Secure the appliance as shown, using
the fixings supplied.
After installation
Check that all the burners are operating
correctly.
20 mm worktop
The flame must not go out on the lowest
setting, or when the control is turned
quickly from a high to a low setting.
On the highest setting, the flame must
have a distinctive and visible core.
30 mm worktop
40 mm worktop
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Connection should be made via a
suitable isolator or a double pole fused
spur connection unit which complies
with national and local safety
regulations and the on/off switch should
be easily accessible after the appliance
has been built in.
All electrical work should be carried
out by a suitably qualified and
competent person, in strict
accordance with current local and
national safety regulations (BS 7671
in the UK).
If the switch is not accessible after
installation (depending on country) an
additional means of disconnection must
be provided for all poles.
Installation, repairs and other work
by unqualified persons could be
dangerous. The manufacturer
cannot be held liable for
For extra safety it is advisable to protect
the appliance with a suitable residual
current device (RCD).
unauthorised work.
Ensure power is not supplied to the
appliance until after installation or
repair work has been carried out.
When switched off there must be an
all-pole contact gap of 3 mm in the
isolator switch (including switch, fuses
and relays).
The appliance must only be
operated when built-in. This is to
ensure that all electrical parts are
shielded. Live parts must not be
exposed.
Important UK
This appliance is supplied for
connection to a single phase 230 V
50 Hz supply with a 3-core cable.
Do not connect the appliance to the
mains electricity supply by an
extension lead. These do not
guarantee the required safety of the
appliance.
The wires in the mains lead are
coloured in accordance with the
following code:
Green/yellow = earth
Blue
= neutral
= live
Please make sure that the connection
data quoted on the data plate match
the household mains supply.
Brown
WARNING
THIS APPLIANCE MUST BE
EARTHED
45
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Important
The electrical safety of this appliance
can only be guaranteed if correctly
earthed. It is most important that this
basic safety requirement is observed
and regularly tested and where there is
any doubt, the electrical wiring in the
home should be tested by a qualified
electrician. The manufacturer cannot be
held liable for the consequences of an
inadequate earthing system such as an
electric shock.
If the connection cable is damaged, it
must be replaced by a suitably
qualified electrician with a special
connection cable of type H 05 V V-F
(pvc insulated), available from the Miele
Service Department.
The manufacturer cannot be held
liable for damage which is the direct
or indirect result of incorrect
installation or connection.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas connection
Depending on country, the hob is
,Connection to the gas supply, or
conversion from one type of gas to
another, should only be undertaken
by an approved and registered gas
installer in strict accordance with
local and national safety and
supplied ready for connection to natural
or liquid gas (refer to label on the
appliance).
United Kingdom:
GB II 2 H 3+ 20 mbar, 28-30/37 mbar
Ireland:
IE II 2 H 3+ 20 mbar, 28-30/37 mbar
building regulations (e.g. Gas Safe
registered in the UK).
Depending on country, a set of jets for
conversion to an alternative type of gas
may be included with the hob.
Every appliance should have its own
easily accessible isolating valve and
test point.
Please contact your dealer or the Miele
Spare Parts Department for the
appropriate conversion jets if
necessary.
Check with your local gas supplier
about the type of gas and its
calorific value and compare this
information with the type of gas
quoted on the hob data plate.
Conversion to another type of gas is
described under "Conversion to another
type of gas".
This appliance is not connected to
an exhaust flue. Please ensure it has
adequate ventilation after
installation.
For any gas work in the UK always
use a Gas Safe registered engineer.
The installer is responsible for
ensuring that the appliance
functions correctly when installed.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Gas connection
Connection
Using a 90° angle
The gas connection must be installed
so that connection can be made either
from inside or outside the kitchen unit,
and the isolating valve must be easily
accessible and visible (by opening one
of the kitchen doors, if necessary).
After installing the appliance the gas
burners have to be set for local
conditions.
When the gas hob has been installed, it
is essential to check that neither the
gas pipe not the electricity cable is in
contact with hot parts of the appliance
or hot gas exhaust, otherwise heat
damage to the pipe and cable could
occur.
cGas connection R 1/2 - ISO 7-1
(DIN 10226)
d90° angle
A test for possible leakages must be
carried out after installation.
Using a 90° angle will increase the
building-in depth in the area of the gas
connection by approx. 60 mm.
Safety regulations demand that a
pressure test point is installed near a
gas hob to allow an engineer to test the
pressure, following servicing.
The appliance is supplied with an
R 1/2" - ISO 7-1 (DIN EN 10226) gas
connection point.
An appropriate rigid connection and
isolating valve must be installed for final
connection.
The gas connection must be so sited
that it is not adversely heated when the
appliance is in operation.
48
Download from Www.Somanuals.com. All Manuals Search And Download.
Burner ratings
Nominal rating
Burner
Gas type
High setting
kW g/h
Low setting
kW
Small burner
Medium burner
Large burner
Wok
Natural gas H
Liquid gas
1.00
1.00
-
0.73
0.27
0.21
Natural gas H
Liquid gas
1.70
1.70
-
124
0.30
0.30
Natural gas H
Liquid gas
2.70
2.60
-
189
0,51
0.64
Natural gas H
Liquid gas
4.50
4.10
-
298
0.27
0.21
Total
Natural gas H
Liquid gas
11.60
11.10
-
808
49
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
,Connection to the gas supply, or conversion from one
type of gas to another, should only be undertaken by an
approved and registered gas installer in strict accordance
with local and national safety and building regulations
(e.g. Gas Safe registered in the UK).
When converting to a different type of gas, the main burner
jets and the small burner jets have to be changed.
Jet table
Main jet C
Small jet C
Natural gas H
Small
Medium
Large
Wok
0.76
0.94
1.20
2x 1.00 / 0.72
0.39
0.42
0.54
0.88 / 0.42
Liquid gas
Small
Medium
Large
Wok
0.52
0.66
0.81
2x 0.66 / 0.46
0.23
0.27
0.39
0.52 / 0.23
The jet markings refer to 1/100 mm of the jet diameter.
50
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
Changing the jets
To change the main jets
Disconnect the gas hob from the
mains electricity supply. Turn off the
gas supply.
Small, medium and large burners
^ Remove the pan support, burner cap
a and burner head b.
^ Using an M7 socket spanner,
unscrew main jet c.
^ Change the main jet.
51
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
Wok burner
^ Remove burner cap ab and burner
head c.
^ Using an M7 socket spanner,
unscrew the main jet d
^ Fit the correct jets securely (see jet
table).
^ Finally, secure the jets against
inadvertent loosening with sealing
wax.
52
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
To change the small jets
Wok burner
To change the small jets, the burner
securing screws must first be loosened
and the upper section of the appliance
removed.
^ Pull the control knobs off.
^ Remove the burner parts.
^ Loosen the screws.
^ Lift the top of the appliance off.
Small, medium and large burners
aSmall jets with smaller diameter (e.g.
for liquid gas: 0.23)
bSmall jets with larger diameter (e.g.
for liquid gas: 0.52)
^ Using a small screwdriver, unscrew
the two small jets a and b in the gas
fitting.
^ Pull out the jets with a pair of pliers.
^ Fit the correct jets securely (see jet
table).
^ Using a small screwdriver, unscrew
small jet a in the gas fitting.
^ Finally, secure the jets against
inadvertent loosening with sealing
wax.
^ Pull out the jet with a pair of pliers.
^ Fit the correct jets securely (see jet
table).
^ Finally, secure the jets against
inadvertent loosening with sealing
wax.
53
Download from Www.Somanuals.com. All Manuals Search And Download.
Conversion to another type of gas
Function test
Check all gas fittings for leaks.
^ Reassemble the appliance.
^ Check the burner flame by operating
the burner.
The flame must not go out on the
lowest setting, or when the control is
turned quickly from a high to a low
setting.
On the highest setting, the flame
must have a distinctive and visible
core.
^ Stick the label supplied with the jets
above the label stating the type of
gas being used.
54
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service, data plate, guarantee
In the event of any faults which you cannot remedy yourself, or if the appliance is
under guarantee, please contact:
– Your Miele dealer, or
– the Miele Service Department (see back cover for address).
Please note that telephone calls may be monitored and recorded to improve
our service.
When contacting Miele, please quote the model and serial number of your
appliance. These are given on the data plate.
N.B. A call-out charge will be applied for service visits where the problem
could have been resolved as described in these instructions.
Space in which to stick the extra data plate supplied with the appliance. Ensure
that the model number is the same as the one on the front of these instructions.
Guarantee
For information on the appliance guarantee specific to your country please
contact Miele. See back cover for contact details.
In the U.K. your appliance is guaranteed for 2 years from the date of purchase.
However, you must activate your cover by calling 0845 365 6640 or registering
55
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved / 2112
M.-Nr. 09 370 470 / 01
Download from Www.Somanuals.com. All Manuals Search And Download.
|