Miele Clothes Dryer T1526 User Manual

Operations Manual

for the T 1526

Vented Dryer

It is essential to read these

operating instructions before

installing or using the machine to avoid

the risk of accident, or damage

to the machine.

]

M.-Nr. 05 017 940

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the machine

1 Supply cable with plug

2 Control panel

3 Drum door

4 Exhaust connection (left or rear)

5 Four height-adjustable legs

Download from Www.Somanuals.com. All Manuals Search And Download.

Guide to the machine

Pushbuttons

Indicator lamps

– Door

– PROGRAM SEQUENCE

The program sequence indicator

lamps show the current state of the

drying program.

This button is used to open the door

(does not stay pushed in).

–

ON /

OFF

When the machine is turned on, the

“On” indicator will light up if the door is

closed. If the door is open, the drum

light will be on.

– DRYING STAGE REACHED

These indicator lamps show which

drying stage the program has

reached. For program stages “Nor-

mal” and “Extra dry” the indicator

lamp remains at the “Normal” posi-

tion.

– Buzzer

Allows the buzzer to sound when the

drum rotates during the anti-crease

cycle.

PROGRAM SETTING-SELECTOR

– Low temp.

Set the required program by turning the

knob either clockwise or counterclock-

wise.

Lower drying temperatures for deli-

cate fabrics, e.g. acrylics (symbol r).

– Start

– COTTONS

Starts the selected program (does

not stay pushed in).

– PERMANENT PRESS

– TIMED DRYING

Items can be either dried for 20

minutes (incl. a cooling-down phase)

or cool air fluffed for 15 minutes.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

WARNING - To reduce the risk of fire,

electrical shock, or injury to persons

when using your appliance, follow

basic precautions, including the follow-

ing:

7. Clean the lint filter before and after

each load.

8. Do not dry articles that have been

previously cleaned in, washed in,

soaked in, or spotted with gasoline,

dry-cleaning solvents, other flamm-

able or explosive substances as they

give off vapors that could ignite or

explode.

1. Read these operating instructions be-

fore using your dryer for the first

time, as this is for your own safety

and for the protection of your ma-

chine.

9. Do not allow children to play on or in

the appliance. Close supervision of

children is necessary when the ap-

pliance is used near the children.

2. Remember to remove the door when

disposing of an old machine to pre-

vent children from accidently locking

themselves in the machine and en-

dangering their lives.

10.To avoid back-pressure or accumula-

tion of exhaust fumes, provide ade-

quate room ventilation, by means of

permanent vents or an open window.

3. Do not install or store this appliance

where it will be exposed to the

weather.

11.Always close the door after use to

prevent children from leaning on the

door and causing the dryer to tilt.

4. Do not install your dryer in rooms

where freezing temperatures may

occur. The reliability of the electronic

control system may be impaired.

12.Keep area around the exhaust open-

ing and adjacent surrounding areas

free from accumulation of lint, dust

and dirt.

5. This machine should only be used for

drying the following fabrics:

– Items which can be machine dried

as specified by the laundry care

label.

– Items which have been washed in

water.

6. The following fabrics pose a fire ha-

zard:

– Items which contain foam rubber,

rubber or rubberlike components.

– Items which have been treated with

inflammable cleaning agents, such

as gasoline or dry-cleaning solvents.

– Items containing hair lacquer, hair-

spray, nail polish remover or similar

substances.

Download from Www.Somanuals.com. All Manuals Search And Download.

IMPORTANT SAFETY INSTRUCTIONS

13.The interior of the machine and ex-

haust duct should be cleaned peri-

odically by qualified personnel.

19.Do not place items exposed to cook-

ing oils in your dryer. Items con-

taimed with cooking oils may contrib-

ute to a chemical reaction that could

cause a load to catch fire.

14.Do not reach into the dryer if the

drum is moving.

15.Do not tamper with controls.

SAVE THESE INSTRUCTIONS

16.Do not repair or place any part of the

appliance or attempt any servicing

unless specifically recommended in

the user maintenance instruction or

in published user repair instructions

that you understand and have the

skills to carry out.

For grounding and electrical connec-

tion instructions, refer to the electri-

cal connection section.

Repairs to electrical appliances

should only carried out by qualified

personnel.

Incorrectly repaired machines may

pose a considerable risk to the user.

17.Formation of lint.

Lint is principally the result of friction

when items are worn and washed.

Machine-drying hardly causes any

lint to form and, as has been estab-

lished by reseach institutes, has no

effect on the lifetime of fabrics.

18.Warning - Do not use fabric sof-

tener/anti static dryer sheets.

Residues from these products block-

up (clog) the lint filter causing prema-

ture failure of the dryer.

Miele dryers are designed to dry

laundry without static cling. How-

ever, should fabric softener be re-

quired, use liquid fabric softener in

the wash cycle.

Clean lint filter mesh monthly by wash-

ing/scrubbing with hot soap and

water.

Download from Www.Somanuals.com. All Manuals Search And Download.

Your contribution to the environment

Disposal of the packing ma-

terial.

The transport and protective packing is

mostly manufactured from the following

recycled or re-useable materials:

Disposal of your old machine.

Old machines contain materials which

can be recycled. Please contact your

recycling center or scrap merchant

and render the machine inoperative as

per the “Important Safety Instructions”

before disposing of the appliance.

– corrugated paper/cardboard

– polystyrene - CFC-free

– polyethylene foil (transparent)

– untreated wood

– fiber board

Please check local environmental regu-

lations before disposing of packing ma-

terials and discarding the appliance.

Download from Www.Somanuals.com. All Manuals Search And Download.

Loading and unloading the machine

If the wash is not removed at the end

WARNING - To reduce the risk of fire,

electric shock, or injury to persons,

read the IMPORTANT SAFETY IN-

STRUCTIONS before operating this ap-

pliance.

of the drying program, the machine

will automatically enter the anti-

crease cycle for 60 minutes. This en-

tails the drum being rotated at short

intervals in order to reduce the forma-

tion of creases.

Load the laundry loosely into the

drum.

Once the laundry has been

Duvet covers and pillowcases

should be fastened before drying in

order to prevent small items from roll-

ing inside of them.

removed, check that the drum is

empty. Any items left in the drum

could be damaged through over-

drying during the next program.

Clean the lint filter after each drying

cycle to prevent excessive energy

consumption, longer program times

and the risk of fire.

The door should always be closed

after use.

Important: Check that laundry can-

not be trapped by the door as this

may cause damage to the fabric.

Download from Www.Somanuals.com. All Manuals Search And Download.

Notes on laundry care

Before drying, check the instructions Notes:

on the fabric care label.

Knitted fabrics and flannel sheets tend

to shrink when washed for the first time

and also when dried. They should not

be overdried (Extra dry)!

The following fabrics should not be

dried in a tumble dryer:

– Woollens and wool blends

These fabrics tend to become matted

and shrink.

Starched laundry can also be dried in

the tumble dryer.

– Items filled with down

The fine fabric interior tends to shrink, Permanent press items should be

depending on the quality of the item

involved.

– Pure linen

briefly spun in the washing machine be-

fore drying. Items which are prone to

creasing should not be dried in the

These items should only be machine- “PERMANENT PRESS- Normal +” - Pro-

dried if specified as suitable by the

manufacturer on the textile care label.

The surface of the fabric may other-

wise tend to become “rough”.

gram.

Drip-dry shirts made of pure cotton

may tend to crease, depending on the

quality of their finish.

Miele dryers have been designed to

dry laundry free of static cling, without

These items should be dried in a

“Hand iron”program.

the use of dryer softener sheets or simi- Permanent press fabrics tend to crease

lar products. The dryer continuously

monitors the moisture content of the

laundry, and automatically shuts off the

heat when the selected degree of dry-

ness is reached. Through the use of a

cool down period, (where the machine

operates without heat), cool, static free

laundry is the end result. Dryer softener

sheets perform the same function by

depositing a chemical residue on both

the clothes and the interior of the dryer.

Over time, this coating may lead to per-

formance reductions in the dryer.

more as the size of the load increases.

This is particularly true of very delicate

fabrics. The load should be reduced to

2 kg or, if necessary, to 1.5 kg.

Do not dry new dark-colored fabrics

together with light-colored items as

they may discolor.

If fabric softening is desired, it is more

convenient, economical and beneficial to

the clothing if a liquid softener is auto-

matically dispensed while the clothes are

in the washing machine. Please see the

washing machine operating instructions

for directions on how to automatically dis-

pense a liquid softener.

Download from Www.Somanuals.com. All Manuals Search And Download.

Program selection

Functional description

– Low temp.

When selected the machines lower

drying temperatures for delicate fab-

rics, (e.g. acrylics, nylon).

An electronic sensor system monitors

the moisture content of the laundry.

Once the required degree of dryness is

reached, cold air enters the drum to

cool the laundry.

– Start

Starts the selected program.

The drying program is then terminated.

“PROGRAM SEQUENCE”

indicators

Function of the pushbuttons

The program sequence indicator lamps

show the current status of the drying

program.

“DRYING STAGE REACHED”

indicators

This indicator shows which drying

stage the program has reached.

“PROGRAM SETTING” selec-

tor

There is a range of settings for both

"Cottons" and "Permanent Press".

In addition, items can be either dried

for 20 minutes (incl. a cooling-cycle

lasting 8 mins.) or fluffed in cool air for

15 minutes.

– Door

This button is used to open the door.

– ON/OFF

When the machine is turned on, the

“On” indicator lamp lights if the door is

closed. When the door is open, the

drum is illuminated.

– Buzzer

When depressed, the buzzer will

sound as the drum rotates during the

anticrease cycle.

Download from Www.Somanuals.com. All Manuals Search And Download.

Program selection

To select a program

To change a program during

drying

Press the "On/Off" button.

Set the program selector to the

desired program.

The new program will start from the be-

ginning.

The tables on the following pages list

the range of applications for the differ-

ent programs.

Correct procedure

1 Press the "On/Off" button.

2Press the "Door" button.

Set the desired program by turning

the program selector either clock-

wise or counterclockwise.

3Open the door and load the machine.

4 Close the door with a firm swing - do

Press the "Start" button.

not push it shut.

The program status will be stored for

30 minutes in the event of a power

failure.

5If drying delicate fabrics, press the

"Low temp." button.

6Select the "Buzzer" if so desired.

7Select a program.

The program is canceled if:

– There is a power failure lasting more

than 30 minutes.

8 Press the "Start" button.

– The door is opened after the ma-

chine has entered the "Cooling

down" or "Anti-crease" stage.

After the program has finished

1 Set the program selector to "Finish".

2 Remove the laundry.

3 Clean the lint filter.

4 Turn off the machine.

Download from Www.Somanuals.com. All Manuals Search And Download.

Programs

Drying stage

Type of laundry/fabric

Max. load

Special instructions

COTTONS

Extra dry

Multi-layer fabrics, mixed

loads of cotton fabrics,

e.g.jeans, towels,

sweatsuits.

6 kg

The “Extra dry” program

should not be selected for

jersey wear items or items

that may shrink.

Uniform loads of cotton

fabrics e.g. flannel items,

underwear, socks.

6 kg

If items are still damp,

select the “Extra dry”

program.

Normal

Normal-

Knitted cotton fabrics

susceptible to shrinkage,

e.g. jersey wear or

If items are still damp,

select the “Normal“

program.

lightweight cotton fabrics.

Cotton or linen fabrics, to

be left damp for easier

ironing.

6 kg

Moisture can be increased

or decreased by using

“Hand iron rr” or “Hand

iron r” respectively.

Hand iron r

Hand iron rr

Cotton or linen fabrics,

including starched laundry,

to be ironed on the rotary

iron, (B865E).

The laundry can be loosely

rolled to prevent it from

drying out until it can be

ironed.

Machine iron

Download from Www.Somanuals.com. All Manuals Search And Download.

Programs

Drying stage

Type of laundry/fabric

Max. load

Special instructions

PERMANENT PRESS

Normal +

Permanent press items

made of synthetic or

blended fabrics, e.g.

pullovers, dresses, pants,

etc., which are not dried

adequately in the “Normal”

program.

3 kg

With blended fabrics

consisting of wool and

synthetics, consult the

manufacturer’s instructions,

as the wool component

may cause the fabric to

matt and shrink.

Permanent press shirts,

table cloths, bedding etc.

made of blended woven or

knitted fabrics, e.g.

3 kg

Normal

cotton/synthetic.

Permanent press shirts,

table cloths, pillowcases

etc. cotton/synthetics,

which are to be pressed.

Hand iron

TIMED DRYING

warm

Individual items, e.g.

comforters, or very small

loads.

This cycle will run for the

full 20 minutes, even if the

clothes are dry sooner.

Items which you want to

"fluff".

6 kg

cool air

Download from Www.Somanuals.com. All Manuals Search And Download.

Cleaning and care

Cleaning the lint filter

Cleaning the dryer

The lint is collected by the lint filter in

the door.

Before cleaning the tumble dryer;

disconnect the machine from the

power supply.

Clean the filter after every program.

Grip the filter by the recessed

handle and pull up to remove.

The dryer can be cleaned using

soapy water or a mild detergent (not

scouring powder) and dried with a

soft cloth.

The drum may be cleaned using a

suitable stainless steel cleaner follow-

ing the manufacturer’s instructions.

The machine must never be hosed

down. Do not use any abrasive sub-

stances or scouring pads to clean

the machine.

Any remaining lint in the hollow part

of the door can be removed through

the gap at the bottom.

The lint filter can be rinsed with water if

necessary.

Dry the lint filter before putting it

back in place.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

Electrical appliances should only be repaired by qualified personnel. Incor-

rectly repaired machines may put the user at risk. There are, however, minor

problems which can be corrected without contacting the Service Department.

What to do if, . . . ?

Cause . . .

Remedy . . .

Check whether the “On”

indicator lights up. If so, failure

to start may be due to an

incorrect program selection

procedure.

Repeat the switch-on procedure

in the correct sequence, as

outlined in the “Program

Selection” chapter.

. . . the tumble dryer fails to

start when turned on?

If the “On” indicator lamp does

not illuminate, check that:

–

The “ON/OFF” button is

depressed.

–

The door is properly closed.

The machine is plugged in

and the fuse or circuit breaker

has not tripped.

The load consists of dissimilar

items (size and fabrics).

Select a longer drying program.

. . . the laundry is not suffi-

ciently dry?

Small loads or individual items

may cause the program to

Small loads can be time-dried.

terminate the cycle prematurely.

The lint filter is clogged.

Clean the lint filter in the door.

. . . the drying times are too

long?

The laundry was not spun in the Make sure that the laundry is

washer for a sufficient time. thoroughly spun before drying.

–

Turn the program selector

to “finish”.

Turn the machine off and

then on again.

. . . the “anti-crease” indicator

lamp in the sequence indica-

tor display starts flashing?

–

Select a program.

Press the “Start” button.

If the indicator lamp starts

flashing again, this indicates a

fault in the machine.

Please contact the Miele

Service Dept.

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

What to do if, . . . ?

Cause . . .

The machine has overheated.

The temperature limiter opened proceed as follows:

the drum door and caused the

machine to turn off

automatically.

Remedy . . .

Before restarting the program,

. . . the drum door opens dur-

ing the drying cycle?

–

Release the ON/OFF button.

Clean the affected part of the

machine.

Possible reasons for

overheating:

–

Turn on the machine again.

Reselect the terminated

program.

–

The lint filter in the door is

clogged.

–

Press the “Start” button.

–

The vent duct is blocked.

The vent aperture (e.g.

louvred window vent, wall

vent) is blocked.

If the drum door opens again,

the Miele Service Dept. should

be contacted.

It only lights up when the

machine is switched on. The

bulb may be burnt out.

See next page.

. . . the interior drum light fails

to function?

. . . you have to open the door

in the event of a power

failure?

Download from Www.Somanuals.com. All Manuals Search And Download.

Problem solving guide

The interior drum light fails to func-

tion: The bulb may be burnt out.

To open the door in the event of a

power failure

Replace it as follows:

Turn off the machine or disconnect

it from the power supply.

Open the door.

Pull forward on the un-hinged side of

the door.

Unscrew the plastic bulb cover lo-

cated inside the drum and above the

door (see illustration).

The light bulb must not exceed the

maximum wattage quoted on the

data plate.

Replace the bulb and the plastic

cover.

The cover must be correctly installed

and tightened, otherwise moisture may

seep in and cause the socket to cor-

rode.

This is a temperature-resistant bulb

and should only be ordered from your

Miele Service Dept.

Download from Www.Somanuals.com. All Manuals Search And Download.

After-sales service

In the event of problems which cannot

be solved, please contact:

– Your Miele Dealer

– The nearest Miele Service Depart-

ment (see back cover for the adress).

When contacting the Service Depart-

ment, please quote the Model and Se-

rial numbers of your appliance, both of

which can be found on the right side

after the door is opened.

Specimen:

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

Grounding and Electrical con-

Electrical connection

nection

This installation should be done by an

experienced and qualified person, in

most cases a licensed electrician, in ac-

cordance with local codes and regula-

tions.

Grounding instructions

This appliance must be grounded.

In the event of a malfunction, ground-

This dryer is supplied with a 1.5 m power

ing will reduce the risk of electric shock

by providing a path of least resistance

for the electric current. This appliance

is equipped with a cord having an

equipment grounding conductor and a

grounding plug. The plug must be

plugged into an appropriate outlet that

is properly installed and grounded in

accordance with all local codes and or-

dinances.

cord with a 3-pole, 4 wire grounding plug,

14-30P (regular Canadian dryer plug).

This plug has to be plugged into a 3-pole,

4 wire grounding receptacle, 14-30R

(regular Canadian dryer receptacle).

The receptacle has to be connected to

Line 1, Line 2, Neutral and Ground wires.

The voltage is 120/240 V AC or 120/208 V AC.

“EASY INSTALLATION KIT”

If you do not have a designated line,

4 wire, 120/240 V – 15 or 30 Amps, for

this appliance, but you have the 4 wire,

120/(208)240 V – 30 Amp Canadian

dryer wall receptacle (14-30 R) you can

use the Miele Double Receptacle Box.

This consists of two standard recep-

tacles 14-30 R, 4 fuses, box and plug

cord, which allows you to use that

single dryer wall receptacle to supply

power to a Miele washer and Miele

dryer. Both machines may operate at

the same time because each uses

maximum about 15 A current.

Warning

Improper connection of the equip-

ment-grounding conductor can re-

sult in a risk of electric shock.

Check with a qualified electrician or

serviceman if you are in doubt as to

whether the appliance is properly

grounded.

Do not modify the plug provided

with the appliance; if it will not fit the

outlet, have a proper outlet installed

by a qualified electrician.

For more information on the electrical

connection on the Miele Double Recep-

tacle Box please contact:

– your Miele dealer

– the nearest Miele Service Depart-

ment.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

Turn the counternuts up and tighten

against the bottom.

Installation

A gap of 10 mm must be main-

tained between the bottom of ma-

chine and the floor. This gap must

not be blocked by deep pile carpet,

plinths etc., as this will prevent a suf-

ficient intake of cold air.

Where to install the machine

The space required by the vent

duct should be taken into consider-

ation when calculating the distance

between the machine and a wall or

other appliances.

The machine should be level to ensure

safe and proper operation. Minor dis-

crepancies do not, however, have an

adverse effect on operation.

The tumble dryer can also be placed

on top of a Miele washing machine (ca-

pacity 6 kg) for a stacked installation.

An appropriate stacking kit is required

and can be obtained from your Miele

dealer, or the Miele Parts Dept.

The machine can be leveled by turn-

ing the legs clockwise or counter-

clockwise as necessary.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

Installing the connector on the left

side of the machine

Exhaust venting

The moist air from the dryer must be

vented to the outside.

Remove the cap covering the ex-

haust part as follows:

The appliance should not be vented

into a chimney, a wall, a ceiling, or

any concealed spaces of the building.

When installing, try to avoid:

– very long venting systems

– too many bends or angles

– tight corners

otherwise . . .

. . . the drying results will be affected,

. . . drying will take longer and use more

energy.

Materials suitable for venting:

– rigid metal pipe

– flexible metal pipe

– Insert a thin screwdriver into the slot

by the retaining hook. Press the hook

gently upwards.

At the same time turn the cap

counterclockwise.

Install the venting in such a way that

the expelled air cannot be drawn

back into the machine.

Do not vent the dryer into a flue

used by gas or fuel boilers or

heaters.

A vent connector is included with the

machine. It should be pressed into the

vent outlet and will simplify the connec-

tion of the exhaust pipe.

Before installation, disconnect the

tumble dryer from the electrical sup-

ply (unplug from the wall socket, or

turn off the circuit breaker.

In the same way remove the vent

socket from the rear exhaust port.

Secure into the side port by pressing

it in and turning it clockwise.

Seal the rear exhaust port using the

cap.

Installation at the rear

The machine comes supplied with

the connector installed on the rear

exhaust port.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

The shorter the exhaust ductwork, the

more efficient the dryer will be. Ex-

pelled air is slowed down in the ducts

due to friction against the inner walls,

therefore the shorter and smoother the

inner walls are, the less friction will

occur.

An elbow or bend creates more friction

than a straight duct. An additional duct

length factor must therefore be added

for each elbow or bend (see Table I).

This factor expresses the resistance of

the bend in terms of a straight length of

duct.

To calculate the effective duct length.

Measure the actual duct length.

Establish the number of elbows or

bends necessary, noting the type of

bend, angle and radius involved

(see Table I).

Add the additional length factor as

specified in Table I to the actual duct

length to give the effective duct

length.

The necessary duct diameter should

then be found in Table II.

Note:

The additional length factor is then

added to the measured duct length to

give the effective duct length.

A larger duct diameter also helps to re-

duce friction. The duct diameter should

therefore be increased with increasing

duct length.

Drying times and energy consumption

remain unaltered for 100 mm duct up to

a total length of 8 m.

Longer duct may lead to slight in-

creases in drying times and energy

consumption but will not impair the

function of the machine as long as the

necessary duct diameter is used (see

Table II).

Tabel I

Type of bend

Angle

Radius in mm

Additional duct

length in m

Flexible metal piping

90°

45°

100-300

300-500

100-500

0.5

0.3

Plain piping

Elbow

90°

100

0.35

2.3

Concertina bend

90°

200

0.7

Wall vent kit with louvres, or window vent kit

Wall vent kit with flap, or window vent kit

3.6

1.25

4,9

Exhaust connection, left side

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

Table II

Example:

Exhaust connection, left . . . . . . . 4.9 m

Length (L) . . . . . . . . . . . . . . . . . . 1.2 m

Lower radius (R = 400 mm) . . . . 0.5 m

Height (H) . . . . . . . . . . . . . . . . . . 1.2 m

Upper radius (R) . . . . . . . . . . . . . 0.5 m

Wall pipe with louvred vent . . . . . 3.6 m

Effective duct length . . . . . . . . . 11.9 m

Effective duct

length (m)

Internal diameter or

edge length (mm)

0-8

8-12

12-17

17-23

23-31

31-41

100

110

120

130

140

150

Flexible ducting has been used for the

following example.

Result:

A duct diameter of 110 mm is adequ-

ate since the effective length is less

than 12 m as specified in Table II.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

Moist air can be ducted outside by a wall

vent or window vent, both of which are

available from most hardware stores.

Window vent kit - example

Wall vent kit - example

1. Louvred window vent frame

4. Louvred window vent

5. Flap

1. Louvred wall vent frame

2. Wall vent duct

3. Adapter

8. Clips (4 pcs.)

9. Raised head screws (4 pcs.)

4. Louvred wall vent

5. Flap

6. Screw

Dryer-side view:

1. Window vent kit

7. Wall anchor

2. Adapter for vent duct

Dryer-top view:

1. Wall pipe

2. Flexible foam-gasket

The window vent kit is installed into in a plexi-

glass pane. If using an existing glass pane, cut a

hole with a diameter of 125 mm.

A flexible foam gasket must be used if the

tumble dryer is directly connected to the wall

vent.

Download from Www.Somanuals.com. All Manuals Search And Download.

INSTALLATION INSTRUCTIONS

Fig. 1

Fig. 3

Ducting (side view) with flexible vent hose to an

exhaust flue.

Connection of piping to the tumble dryer.

1. Drain pipe

2. Adapter for vent duct between tumble dryer

and plastic drain pipe

1. Wall vent duct A. Wire spiral-wound hose

2. Adapter

B. Flexible ducting

3. Flue isulated against damp

Fig.4

Fig. 2

Height of vent outlet for washer dryer stack.

Ducting (side view) with plastic piping to a wall

vent kit.

1. Wall vent kit

2. Adapter

3. Drain pipe (outer dia. 110 mm)

Download from Www.Somanuals.com. All Manuals Search And Download.

Technical data

Height. . . . . . . . . . . . . . . . . . . . . . . . . .

85 cm (adjustable +1/-0.5 cm)

59.5 cm

Width . . . . . . . . . . . . . . . . . . . . . . . . . .

Depth (incl. distance from wall) . . . . . .

Weight . . . . . . . . . . . . . . . . . . . . . . . . .

Drum volume . . . . . . . . . . . . . . . . . . . .

Capacity. . . . . . . . . . . . . . . . . . . . . . . .

Rated load . . . . . . . . . . . . . . . . . . . . . .

Fuse rating . . . . . . . . . . . . . . . . . . . . . .

70 cm

57 kg

126 l

6 kg dry laundry

See Data Plate

Download from Www.Somanuals.com. All Manuals Search And Download.

Consumption data

load

Final spin speed in washer*

Electrical

consumption

Drying time

incl.

cooling down

time

rpm

kwh

mins

Cottons

1200

1400

1600

3.65

3.50

3.20

Extra dry

1200

1400

1600

3.15

3.00

2.70

Normal

Normal-

800 (70 % residual moisture)

3.85

3.00

2.85

2.55

1200

1400

1600

800 (70 % residual moisture)

3.10

2.25

2.10

1.80

Hand iron rr

1200

1400

1600

1200

1400

1600

1.80

1.65

1.35

Machine iron

Permanent Press

1000

1000 (50 % residual moisture)

1000

1.49

1.40

1.20

Normal +

Normal

Hand iron

The specified program running times and electrical consumption values were established under stand-

ard conditions (EN 61121/A11).

Different types of fabrics, load size and residual moisture after spinning may effect the specified

values.

*These values apply if the laundry is spun in a Miele washing machine before drying.

Download from Www.Somanuals.com. All Manuals Search And Download.

3498

This paper is made from 100% chlorine-free bleached cellulose and therefore protects the environment.

Download from Www.Somanuals.com. All Manuals Search And Download.

Nikon Camera Lens 1928 User Manual
Nokia Cell Phone Accessories Nokia 6210 User Manual
NordicTrack Treadmill NTTL15083 User Manual
NuTone Ventilation Hood F305C User Manual
Oki Printer 3390 User Manual
Omega Thermometer TC 08 User Manual
Omnimount TV Mount 1100171 User Manual
Oregon Scientific Games BW68 User Manual
Orion Car Audio Car Stereo System ORRPA User Manual
Palsonic CRT Television 5125PF User Manual