Operating instructions
for vented tumble dryer
T 4162
To avoid the risk of accidents
or damage to the machine
it is essential to read these
instructions before it is installed
and used for the first time.
G
M.-Nr. 06 619 190
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Caring for the environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Disposal of the packing material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Disposal of your old appliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Energy saving tips . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Warning and Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Notes on laundry care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Care symbols. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Tips on drying . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
How to dry correctly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Brief instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Low temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Changing the programme sequence. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Programme chart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Cleaning and care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Cleaning the fluff filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Tumble dryer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Problem solving guide. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
General problems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Check and fault indicator lamps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Changing the lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
After sales service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Repairs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Appliance guarantee . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Optional accessories. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Contents
Installation and connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Front view. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Installation site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Transporting the machine to its installation site . . . . . . . . . . . . . . . . . . . . . . . . 25
Building under a continous worktop / in a kitchen run . . . . . . . . . . . . . . . . . . . 25
Levelling the machine. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Washer-dryer stack. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Electrical connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Electrical connection U.K. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Installation - venting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Calculating the effective duct length: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Installation to the left or right side of the machine. . . . . . . . . . . . . . . . . . . . . . . . . 30
Adapter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
aVenting system with flexible ducting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
bVenting system with plastic piping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
cConnecting directly to a wall vent . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Washer dryer stack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Consumption data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Technical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Programmable functions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Altering the residual moisture level in the Cottons programmes . . . . . . . . . . . . . . 40
Altering the residual moisture level in the Minimum iron programmes . . . . . . . . . 41
Activating and deactivating the buzzer. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Extending the cooling down time . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Changing the standard drying level in the Minimum iron - Normal programme . . 44
Changing the standard drying level in the Automatic programme . . . . . . . . . . . . 45
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
Technical safety
To avoid the risk of accidents and
Before setting up the machine,
check it for any externally visible
damage.
Do not install or use a damaged
machine.
damage to the machine please read
these instructions carefully before
using it for the first time. They
contain important information on its
safety, installation, use and
maintenance.
Keep these instructions in a safe
place and ensure that new users are
familiar with the content. Pass them
on to any future owner of the
machine.
Before connecting the machine,
ensure that the connection data on
the data plate match the mains
electricity supply. If in any doubt,
consult a qualified electrician.
The electrical safety of this
machine can only be guaranteed
when continuity is complete between it
and an effective earthing system which
complies with local and national safety
regulations. It is most important that this
basic safety requirement is present and
regularly tested, and where there is any
doubt the household wiring system
should be inspected by a qualified
electrician. The manufacturer cannot be
held liable for the consequences of an
inadequate earthing system (e.g.
electric shock).
Correct use
The tumble dryer is only intended
for drying fabrics which have been
washed in a water solution, marked on
the manufacturer's care label as being
suitable for tumble drying.
"Dry cleaning kits" for freshening up
garments in a tumble dryer are
increasingly available on the market. If
using, do so at your own risk, and
follow the instructions provided on the
packaging.
Any other applications may be
dangerous. The manufacturer is not
liable for damage resulting from
improper use or operation.
Do not connect the machine to the
mains electricity supply by an
extension lead. Extension leads do not
guarantee the required safety of the
appliance (e.g. danger of overheating).
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
The machine is built in accordance
with current safety requirements.
Unauthorised repairs could result in
unforeseen dangers for the user, for
which the manufacturer cannot accept
liability. Repairs should only be
undertaken by a Miele approved
technician.
Ensure current is not supplied to the
machine until after maintenance or
repair work has been carried out.
Faulty components must only be
replaced by genuine Miele original
spare parts. Only when these parts are
fitted can the safety standards of the
machine be guaranteed.
If the connection cable is faulty it
must only be replaced by a Miele
approved service technician to protect
the user from danger.
In countries where there are areas
which may be subject to infestation
by cockroaches or other vermin, pay
particular attention to keeping the
machine and its surroundings in a
clean condition at all times. Any
damage which may be caused by
cockroaches or other vermin will not be
covered by the machine guarantee.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
In the event of a fault or for
Adequate ventilation is essential to
cleaning purposes, the machine is
only completely isolated from the
electricity supply when:
avoid the danger of asphyxia and
toxic fumes where another appliance
which also uses the room air (e.g. gas,
oil or coal fired heater, continuous flow
or other water heater) is installed in the
same or an adjacent room.
– it is switched off at the wall socket
and the plug is withdrawn, or
– it is switched off at the mains, or
– the mains fuse is withdrawn, or
To ensure safe operation, and to
prevent gases given off by these
appliances being drawn back into the
room, an underpressure of 0.04 mbar is
the maximum permissible.
– the screw-out fuse is removed (in
countries where this is applicable).
– Ventilation can be maintained by air
inlets which cannot be blocked, in
windows, doors and outside wall
vents, or by fitting a window contact
switch which ensures that the tumble
dryer can only be operated when the
window is opened wide enough.
Use
This equipment may only be used
in mobile installations such as
ships, caravans, aircraft etc. if a risk
assessment of the installation has been
carried out by a suitably qualified
engineer.
If in doubt, the advice of a competent
builder, or for gas, a "Corgi" registered
installer (in the UK) must be sought.
This dryer must not be:
– connected to a chimney or vent flue
which is in use.
The exhaust air must not be vented
into a chimney or vent flue which is
in use, nor should it be connnected to
ducting which ventilates rooms with
fireplaces. It would be dangerous if
smoke or exhaust fumes were drawn
back into the room.
– used without exhaust ducting.
– used without the fluff filter in place or
if the fluff filter is damaged in any
way.
Check all parts of the extraction
system on a regular basis (e.g. wall
vent, external grille, bends in the
ducting etc.) and make sure they are all
free of any hindrance. A build-up of fluff
will prevent a free-flow of air through the
system. If the dryer is to be connected
to an existing ducting system this must
be checked for suitability beforehand.
Do not install the machine in a
room where there is a risk of frost
occurring. At temperatures around
freezing point the machine may not be
able to operate properly.
The ambient room temperature should
be between +2°C and +35°C.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Warning and Safety instructions
To prevent the risk of fire the
following textiles must not be
dried in this machine:
Safety with children
This machine is not a toy. To avoid
the risk of injury keep children
– fabrics which contain a large
proportion of rubber, foam rubber or
rubber like materials.
away from the machine at all times and
supervise them whilst you are using it.
Do not allow children to play on or near
it or to play with its controls. Supervise
its use by the elderly or infirm.
– items which contain damaged
padding or fillings (e.g. pillows,
jackets).
Using accessories
– items which have been treated with
inflammable cleaning agents.
Accessory parts may only be fitted
when expressly approved by Miele.
– items which have been splashed with
hair lacquer, hair spray, nail varnish
remover or similar substances.
If non-Miele parts are used with this
machine, guarantee, performance and
product liability claims may be
invalidated.
– items which have been soiled with
oils or residues containing grease
(kitchen oils, cosmetics etc.).
Disposal of your old machine
– items soiled with wax or other
chemicals (e.g. mops and floor
cloths).
Before discarding an old machine,
switch it off at the wall socket and
unplug it. Render the plug useless and
cut off the cable directly behind the
machine. This should be done by a
competent person.
– items which have not been
thoroughly cleaned and which are
still soiled with grease or oil, e.g.
workwear. Such clothing may require
a heavy duty detergent to get them
clean. If necessary consult the
detergent manufacturer for advice.
The manufacturer cannot be held
liable for damage caused by
non-compliance with these Warning
and Safety instructions.
Do not let anyone sit or lean on the
door, as this can cause the
machine to tip up.
Always close the door after use.
This way you will avoid the danger
of:
– children climbing onto or into the
dryer or hiding things in it.
– pets or other small animals climbing
into it.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
aProgramme selector
eDoor Button
The programme selector can be
turned clockwise or anti-clockwise.
To open the door / to cancel a
programme.
Pressing this button will open the
door even when the machine is
switched off at the mains.
bProgramme sequence and check
lamps
cStart button
If the machine is switched on at the
mains and the door is opened the
drum lighting will come on. It will go
out a few minutes later to save
energy.
Press the Start button to start a
programme.
The Start indicator lamp will flash as
soon as a programme can be
started. It lights up constantly once
the programme has started.
PC indicator light
dI-On/0-Off button
The indicator light marked PC is used
by Miele Service technicians as an
optical interface.
To switch the machine on or off / to
interrupt a programme.
The Anti-crease/Finish lamp will light
up as confirmation that the machine
has been switched on.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Notes on laundry care
Care symbols
– Down-filled garments have linings
which have a tendency to shrink,
depending on the quality of the item.
They can be partially dried using the
Smoothing programme.
Before drying check the drying symbol
on the care label. If there are no
symbols, dry at your own risk!
q . . . . . . . . . Dry at normal temperature
r . . . . . . . . . . Dry at a low temperature
s . . . . . . . . . . . . . . . Do not tumble dry
– Pure linen should only be machine
dried if specified as suitable by the
manufacturer on the care label, as
the surface of the fabric may
– For delicates and fabrics with the
following care label r select Low
temperature.
otherwise become rough. They can
be partially dried using the
Smoothing programme.
Tips on drying
– Loopknit garments (e.g. T-shirts and
underwear) tend to shrink depending
on their quality. Do not over-dry these
textiles. When purchasing these
– Always observe the maximum
recommended loads given in the
"Programme chart". Never overload
the drum.
garments it is advisable to take their
shrinkage properties into account.
Overloading can cause unnecessary
wear and tear to the laundry, give a
disappointing drying result and
cause more creasing.
– Minimum iron fabrics and 100%
cotton shirts or blouses tend to
crease more, the greater the load.
This is especially true of very fine
weaves.
– Do not put soaking wet items into the
tumble dryer. Spin them thoroughly
after washing using the appropriate
spin speed.
Reduce the load or use the Minimum
iron - Hand iron programme.
– Starched laundry can be dried in the
tumble dryer. To achieve the usual
finish, double the amount of starch
should be used.
– Use the Automatic programme for
drying mixed loads of cottons and
minimum iron fabrics.
– New dark coloured garments should
be washed and dried separately
from light coloured garments to avoid
the danger of colours running and
discolouring other garments or even
plastic components in the machine.
Dark coloured fibres can also settle
on light coloured garments and vice
versa.
– Open jackets so that they can dry
evenly.
– Woollens and wool blends tend to
become matted and shrink if dried in
a tumble dryer. They can, however,
be partially dried using the Woollens
hand care programme.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
Brief instructions
C Load the tumble dryer
The headings numbered (A, B, C ...)
show the operating sequence and can
be used as a brief guide to using your
machine.
^ Press the Door button to open the
door.
^ Load the laundry loosely into the
drum.
A Sort the laundry
Do not overload the drum. See the
"Programme chart" for
recommended loads for each
programme.
Overloading can cause unnecessary
wear and tear to the laundry and
give a disappointing drying result.
To ensure an even drying result
separate out the washed laundry and
sort it according to: . .
. . . the drying level required
. . . the type of fibre or weave
. . size
. . the moisture content after spinning.
^ Before closing the door make sure
the fluff filter is correctly positioned.
,Make sure that objects e.g.
detergent dispensing balls have
been removed from the laundry.
They could melt, and cause damage
to the dryer or the laundry.
– Check seams and stitching to ensure
that padding and linings are intact.
– Fasten duvet covers and pillow
cases to prevent small items from
being trapped inside them.
– Fasten hooks and eyes etc.
– Tie fabric belts and apron strings.
– Sew in or remove underwiring from
bras.
Check the laundry is right inside the
drum so that it cannot get trapped or
damaged when the door is shut.
B Turn on the tumble dryer
^ Switch the dryer on by pressing the
I-On/0-Off button in.
^ Shut the door either with a gentle
swing, or lean against it and push it
shut.
The tumble dryer may be switched on
after loading, saving energy as the light
will not come on.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
D Select a programme
E Start the programme
^ Press the Start button.
The indicator lamp for the Start button
will then change from flashing to being
on constantly.
The drying cycle begins.
Depending on the programme
selected, the drying stage reached is
shown by the sequence indicator lamps
on the right hand side of the control
panel.
Before the end of a programme
^ Turn the programme selector to the
required programme.
The cooling down phase takes place
before the end of a programme so that
the garments are not too hot to handle
(the Cool air indicator lamp will come
on). The programme is not finished until
the cooling down phase is complete.
The Woollens handcare and Smoothing
programmes do not include a cooling
down phase.
Low temperature
^ For drying particularly sensitive
fabrics (care symbol r) e.g. acrylics
turn the programme selector to the
Low temperature position.
Because the heater rating is reduced
for the Low temperature setting clothes
dry more slowly thus lengthening drying
times.
At the end of a programme
The Anti-crease/Finish indicator lamp
comes on.
The drum will continue to rotate at
intervals to prevent laundry creasing, if
you do not wish to remove it immediate-
ly. The anti-crease phase lasts for an
hour. There is no anti-crease phase on
the Woollens handcare programme.
During the anti-crease phase . . .
. . . (depending on the programme
selected) the indicator lamp for the
drying stage reached will also light up.
. . . the buzzer will sound at intervals.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
How to dry correctly
F Remove the laundry
^ Press the Door button.
^ Open the door.
Other programmes:
^ Press the Start button.
To cancel a programme
^ Remove the laundry.
^ Turn the programme selector to
Finish or open the door .
Make sure that the drum is empty. If
items are left in the dryer, they could
be damaged by overdrying when
the dryer is next used.
Adding or removing laundry after a
programme has started
^ Press the Door button.
^ Switch the dryer off by pressing the
l-On/0-Off button.
^ Open the door.
^ Clean the fluff filter in the door.
,Do not touch the back of the
drum when adding or removing
items. The drum could be very hot -
danger of burning.
^ Close the door.
Changing the programme
sequence
^ Add or remove items.
^ Close the door.
Changing a programme while it is
running
^ Press the Start button.
As long as the cooling down phase or
the anti-crease phase has not been
reached, it is possible to change a
programme after it has started by
turning the programme selector to a
different programme position.
To interrupt a programme
^ Switch the machine off with the
I-On/0-Off button.
To continue drying:
^ Switch the dryer on with the
I-On/0-Off button.
The programme will continue (only with
the Cottons, Minimum iron and Auto-
matic programmes).
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Cottons
Max. load: 6 kg*
Normal+, Normal**, Low temperature
Fabric
type
Single and multi-layered cottons fabrics such as towelling, jerseywear,
underwear, flannelette bed linen.
Note
– Select Low temperature for fabrics with the r symbol. Laundry is
dried at a lower temperature.
Hand iron**, Machine iron
Fabric
type
Cottons and linen fabrics, e.g. table linen, bedlinen, starched laundry.
Note
To prevent laundry from drying out it should be rolled up until you are
ready for ironing.
Minimum iron
Max. load: 3 kg*
Normal**, Low temperature, Hand iron
Fabric
type
Minimum iron items made of cotton, synthetic or blended fabrics, e.g.
shirts, blouses, skirts and table cloths.
Notes
– Select Low temperature for fabrics with the r symbol (e.g. acrylic
garments). Laundry is dried at a lower temperature.
– Select Hand iron for delicate fabrics and to reduce creasing even
more, reduce the load to 1.5 kg*.
– In the Miniumum iron Hand iron programme, items are dried with
very little creasing, depending on fabric type and amount of load.
*
Weight of dry laundry
** Note for test institutes:
Programme setting for testing in accordance with EN 61121
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Programme chart
Automatic
Max. load: 3 kg*
Fabric
type
Mixed load of cotton and minimum iron fabrics.
Timed drying
Warm air
Max. load: 6 kg*
Fabric
type
– Multi-layered fabrics whose layers have different drying
characteristics, e.g. jackets, pillows.
– For drying individual items, e.g. bath towels, bathing costumes,
tea-towels.
Cool air
Fabric
type
Any item which only needs airing.
Woollens handcare
Max. load: 2 kg*
Fabric
type
Woollen fabrics
Notes
– To refresh and fluff up woollen garments quickly. Woollen fabrics
are not dried completely by this programme.
– Remove garments as soon as the programme has finished and
leave to finish drying at room temperature.
Smoothing
Max. load: 3 kg*
Fabric
type
– Cottons and linen fabrics.
– Minimum iron items made of mixed fibres, cottons or synthetics e.g.
trousers, jackets, shirts.
Notes
– Smooths out creasing caused during the spin cycle in the washing
machine.
– Fabrics are not completely dried in this programme. Remove
garments as soon as the programme has finished and leave to
finish drying at room temperature.
*
Weight of dry laundry
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Cleaning the fluff filter
^ Remove any fluff from the hollow part
of the door holder.
The fluff which is created by the
drying process is collected in the fluff
filter in the door. Clean the filter after
every drying cycle.
A cleaning brush is available as an
optional extra from your Miele dealer
or the Miele Spare Parts Department.
You can also use a vacuum cleaner.
^ Also clean the door seal (2) with a
damp cloth.
If there is a great deal of compacted
fluff on the filter, it can be cleaned
under running water.
^ After cleaning shake thoroughly until
no more water droplets are visible.
^ Dry the filter carefully.
^ Once clean, push the filter back into
the door holder until it clicks into
position. Ensure it is facing the
correct way. Close the door.
^ Open the door and pull the fluff
filter (1) out of the door as illustrated.
^ Use your fingers to remove the fluff
from the surface of the filter.
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Cleaning and care
Tumble dryer
Disconnect the machine from the
power supply.
^ Clean the housing and control panel
with a mild cleaning agent or soapy
water.
Clean the drum and other stainless
steel parts with a suitable proprietary
stainless steel cleaner following the
manufacturer’s instructions.
Do not use solvents, abrasive
cleaners, glass cleaners or
all-purpose cleaners. These could
damage plastic surfaces and other
parts. The machine must never be
hosed down.
^ Dry all parts with a soft cloth.
E-Cloth
A microfibre "E-Cloth" is available from
the Miele UK Spare Parts Department,
which is suitable for cleaning surfaces
such as stainless steel, glass, plastic
and chrome without the use of
chemicals.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
With the help of the following notes minor faults in the performance of the
machine, some of which may result from incorrect operation, can be put right
without contacting the Service Department.
,Repair work to electrical appliances should only be carried out by a
suitably qualified person in strict accordance with local and national safety
regulations. Repairs and other work by unqualified persons could be
dangerous. The manufacturer cannot be held liable for unauthorised work.
General problems
Problem
Possible cause
Remedy
The tumble dryer fails to No obvious cause.
start when switched on.
– Have you followed the
switch-on procedure
correctly (see “How to
dry correctly”)?
– Is the plug correctly
inserted in the socket
and switched on?
– Is the door closed
properly?
– Has the fuse or circuit
breaker tripped?
Items made of synthetic Synthetic fibres tend to
fibres are charged with attract static charge.
static electricity after
Static charge can be
reduced by adding a
fabric conditioner to the
final rinse in the washing
machine or a fabric
drying.
conditioner sheet to the
load in the dryer.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
There is a build
up of fluff.
Fluff is principally the result of Fluff is collected by the fluff
friction when garments are
being worn and washed.
Machine drying hardly
filter and can be easily
removed (see "Cleaning and
Care").
causes any fluff to form and
has been established by
research institutes to have no
appreciable effect on the
lifetime of the garment.
The laundry is
not sufficiently
dry.
The load consisted of
different fabrics.
– Finish drying using "Timed
drying - Warm air".
– Select a more suitable
drying programme next
time (see "Programme
chart").
The interior drum The lighting switches off
lighting does not automatically (to save
Switch the dryer off and then
on again.
come on.
energy).
The lamp needs changing.
Change the lamp as
described at the end of this
section.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Problem
Possible cause
Remedy
The drying
Important: Before attempting to remedy one of the following
process goes on causes, switch the dryer off and switch on again to start the
too long or even programme again.
switches off.
Ventilation to the dryer is
Open a door or window while
insufficient (e.g. because it the machine is in operation for
is installed in a room which increased air flow.
is too small).
The fluff filter may be
blocked.
Remove any fluff.
The vent ducting or the
ventilation outlet is blocked.
– Check all parts of the
extraction system on a
regular basis (e.g. wall vent,
external grille, bends in the
ducting etc.) and make sure
they are all free of any
hindrance.
– Remove any fluff.
The laundry has not been
spun sufficiently.
Make sure that your laundry is
thoroughly spun at the
appropriate spin speed.
The tumble dryer has been Do not exceed the maximum
overloaded.
load for the programme
selected.
Metallic components, e.g.
zips have prevented the
dryer from registering the
correct moisture level in the
laundry.
– Close zips and fasten any
hooks next time.
If the problem occurs again,
dry garments with long zips
using "Timed drying - Warm
air".
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Check and fault indicator lamps
Problem
Possible cause
Remedy
The programme has
stopped. The
This is not a fault.
Use the "Timed drying -
Warm air" programme to
dry individual items.
The electronic unit has
recognised that there is no
laundry in the drum and
Anti-crease/Finish
lamp has come on in
the sequence display
and the buzzer is
sounding.
Before changing a
cancelled the programme. programme: Open and
close the drum door.
Drying individual garments
or items which are already
dry can also cause the
programme to be stopped.
The programme has
been interrupted. The
indicator lamp for
Hand iron or Machine
iron is flashing, and
the buzzer sounds.
No obvious cause.
– Switch the dryer off and
then on again.
– Then start the
programme again.
If the programme stops
again and the fault
message reappears there
is a fault. Contact the
Miele Service
Department.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem solving guide
Changing the lamp
The lamp specification and
Disconnect the machine from the
mains electricity supply.
maximum wattage is stated on the
data plate and on the lamp cover.
^ Open the door.
^ Replace the lamp.
You will find the interior lamp cover at
the top of the drum aperture.
^ To close the cover push it upwards
and press it on the left and right until
you hear it click into position.
,Ensure that it is fitted into
position securely, as any moisture
could cause a short circuit.
^ Insert a suitable tool, such as a wide
bladed screwdriver, under the side
edge of the lamp cover as illustrated.
^ Apply a little pressure and whilst
doing so turn your wrist in the
direction of the arrow to open the
cover.
The cover will open downwards.
The temperature resistant lamp should
only be ordered from your Miele dealer
or the Miele Spare Parts Department.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
After sales service
Repairs
Appliance guarantee
In the event of any faults which you
cannot remedy yourself, or if the
machine is under guarantee, please
contact
Please see the guarantee card
supplied with your machine.
Optional accessories
– your Miele dealer, or
Optional accessories for this dryer is
available from your Miele Dealer or from
the Miele Spare Parts Department.
– the Miele Service Department
(see back cover for contact details).
When contacting your Dealer or the
Service Department, please quote the
model and serial number of your
machine, both of which are shown on
the data plate situated on the right
hand side below the drum aperture.
Please note that telephone calls may
be monitored and recorded to
improve our service.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Front view
aVenting connection: rear, right or left
(supplied with the rear socket open)
bMains connection cable
cControl panel
dDoor
eFour height adjustable screw feet
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Installation site
With niche heights of:
– 840 mm, longer screw feet* are
required.
,Make sure the dryer door can be
opened without hindrance after
installation.
– 870/885 mm - 915/930 mm, one or
two height adjustment frames* are
required.
Transporting the machine to its
installation site
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
When moving the machine you can
hold it by the lid where it protrudes to
the rear of the dryer. To manoeuvre the
dryer out of its packing case to its
installation site you will also need to
hold it by the front feet.
If you wish to push your machine under
a worktop and there is space to do this
without removing the lid, the building
under kit is not necessary. Otherwise
the building under kit is essential.
Building under a continous worktop /
in a kitchen run
Replacing the lid
The space required by the vent duct
must be taken into consideration when
calculating the distance between the
machine and a wall or other appliances
or furniture on either side.
If the lid has been removed in order to
fit a coverplate, ensure that, if the lid is
ever replaced, it fits securely into the
rear holders. Otherwise, it is not
properly secure for transport.
,A building under kit* is required
which must be fitted by a suitably
qualified person.
The machine lid is replaced by a
coverplate.
It must be fitted by suitably qualified
person to ensure electrical safety.
The building-under kit is supplied with
its own installation instructions.
N.B. When built under drying times may
be longer.
– The electrical socket must be
located in an accessible position
near the machine.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation and connection
Levelling the machine
,A ventilation gap of 10 mm must
be maintained between the base of
the machine and the floor. It must
not be blocked by deep pile
carpets, plinths, etc as this would
prevent a sufficient intake of air.
Washer-dryer stack
The tumble dryer can also be
combined with a Miele washing
machine in a washer-dryer stack. To do
this the appropriate stacking kit* (WTV)
to match your washing machine is
required.
The machine must be perfectly level to
ensure safe and proper operation.
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
,Stacking kits must only be
installed by a suitably qualified fitter.
^ The screw feet can be adjusted to
compensate for any unevenness in
the floor.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
Electrical connection U.K.
Non-rewireable plugs BS 1363
All electrical work should be carried out The fuse cover must be refitted when
by a suitably qualified and competent
person, in strict accordance with
current national and local safety
regulations (BS 7671 in the UK).
changing the fuse, and if the fuse cover
is lost, the plug must not be used until a
suitable replacement is obtained. The
colour of the correct replacement cover
is that of the coloured insert in the base
of the plug, or the colour that is
embossed in words on the base of the
plug (as applicable to the design of
plug fitted).
Ensure power is not supplied to the
appliance until after installation work
has been carried out.
The appliance is supplied with a mains
cable with moulded plug ready for
connection to a 230-240V mains
supply. Please ensure the connection
data quoted on the data plate match
the household mains supply.
Replacement fuses should be ASTA
approved to BS 1362 and have the
correct rating. Replacement fuses and
fuse covers may be purchased from
your local electrical supplier.
Connection should be made via a
suitable switched socket which is easily
accessible after installation.
WARNING: THIS APPLIANCE
MUST BE EARTHED
For extra safety it is advisable to install
a residual current device (RCD), with a
trip current of 30 mA (in accordance
with DIN VDE 0664, VDE 0100 Section
739).
Do not connect via an extension lead.
Extension leads do not guarantee the
required safety of the appliance (e.g.
danger of overheating).
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
General
Avoid:
– very long ducting systems
Important
– too many bends or corners, tight
corners
Before operating the tumble dryer, a
suitable ducting system must be
installed to carry the moist air from
the dryer to the outside. This can be:
. . . flexible ducting hose, or plastic
piping connected to the dryer, or
. . . the dryer may be connected
directly to the wall vent.
Otherwise the drying result will be less
effective and it will take longer and use
more energy.
Suitable materials
– for the ventilation ducting:
flexible ducting* or plastic piping
with a diameter of at least 100 mm.
– Before installing the ducting system,
ensure that the machine is not
– for venting to the outside:
connected to the power supply.
a wall pipe kit* or a window vent kit*.
– The ducting outlet (e.g. wall pipe)
should be installed in such a way
that the moist expelled air . . .
* Available as an optional accessory
from your Miele dealer or the Miele
Spare Parts Department.
. . . cannot be drawn back into the
room in which the dryer is installed;
. . . cannot cause any damage to the
building or other nuisance.
Procedure
^ First measure the duct length
required. Calculate the effective duct
length and establish the internal duct
diameter required (use the tables on
the next page).
– The dryer uses the room air. It is
therefore essential to ensure
adequate ventilation to avoid the
danger of asphyxia caused by gases
given off by other appliances being
drawn back into the room.
Insufficient ventilation will also cause
drying times to be considerably
longer.
^ Then decide which type of ducting
you want to use (see "Venting
systems" in this section).
Ventilation can be maintained by:
- an open window;
- an air inlet which cannot be
blocked in windows, doors and
outside wall vents;
- a window switch which prevents
the dryer being used when the
window is closed.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Calculating the effective duct
length:
2. Internal duct diameter
^ Refer to Table II for the appropriate
duct diameter required.
Friction against the inner walls of the
ducting will slow down the expelled air
as it passes through. An elbow, bend,
non-return flap or wall vent creates
more friction than a straight duct. The
friction created by each of these is
expressed as an additional duct
length factor. The additional length
factors are calculated by comparing
the friction created by, for example, an
elbow to that created by 1 metre of
straight plastic piping (Table I).
Table I
Additional
duct length
factor
Flexible ducting*
– 1 m laid straight
– 45° angle
(Bend radius = 0.25 m)
– 90° angle
(Bend radius = 0.25 m)
1.8 m
1.5 m
2.5 m
Flexible aluminium ducting* / plastic
piping
– 1 m laid straight / or 1 m straight
1.0 m
0.6 m
0.8 m
The additional duct length factor for
each item needs to be added together
to ascertain the effective duct length
required.
pipe
– 45° angle / elbow
(Bend radius = 0.25 m)
– 90° angle / elbow
(Bend radius = 0.25 m)
A larger internal duct diameter also
helps reduce friction. If the effective
duct length is more than 20 m the
duct diameter should be increased
(Table II).
Wall vent kit* or window vent kit*
– with louvred grille
– with non-return flap (hinged flap)
Non-return flap* to be integrated into 14.3 m
the vent ducting
3.8 m
1.5 m
Flat ducting (for washer dryer
stack)*
11.0 m
1.0 m
1. To calculate the effective duct
length required:
Venting connection to the left/right
* optional accessory from Miele
^ First measure the distance which will
require straight ducting. Multiply this
amount by the corresponding
Table II
Maximum effective
Internal duct
additional duct length factor in Table I.
duct length allowable
diameter
required
^ Establish the number of angles,
bends etc. necessary and add their
additional duct length factors
10 m with Ring adapter
100 mm
20 m without Ring adapter 100 mm
40 m without Ring adapter 125 mm
100 m without Ring adapter 150 mm
together with the help of Table I.
^ Add all the additional duct length
factors together to get the effective
duct length.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
3. Example
Installation to the left or right
side of the machine
At the rear
The connection is opened at the
factory.
^ Fit one of the venting systems
described on the following pages.
Left or right side of the machine
A
Wall pipe, with louvred vent
= 1 x 3.8 m Additional duct
length
= 3.8 m
= 1.6 m
= 0.5 m
B/D 2 Elbows, 90°
= 2 x 0.8 m Additional duct
length
C
E
0.5 m plastic piping
= 0.5 x 1 m Additional duct
length
^ Remove the left or right hand side
cover cap. Do not remove the frame.
Refit it in the rear outlet.
Side connection, left
= 1 m Additional duct length
Effective duct length
= 1.0 m
= 6.9 m
Result: A duct diameter of 100 mm is
adequate as the effective duct length is
less than the 20 m specified in Table II.
^ Ensure it is securely in position so
that it cannot fall out when the dryer
is in operation.
^ Fit one of the venting systems
described on the following pages.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Venting systems overview
aVenting system with flexible
ducting
The various venting systems which are
possible (a b c) are described on
the following pages.
This is a simple, cost effective
method of directing the moist air
outside. The adapter is fitted into the
vent opening on the dryer and the
ducting hose is then connected to
the adapter.
Adapter
^ The following items are required:
... flexible ducting hose
... a wall vent kit* or window vent kit*.
* (Miele optional accessory).
A ring adapter** (1) is installed in
adapter (2) for the installation of a
flexible vent duct. It reduces time and
energy requirements during drying
when used in combination with a short
vent duct (maximum 10 m total
length). The ring adapter is removable
and designed for use with all venting
systems.
^ Ring adapter (1) must be taken out of
adapter (2), if the total duct length is
longer than 10 m.
If the total duct length is less than 10
m the ring adapter should be left in
the adapter.
** Note for test institutes: EN 61121 Standard
testing is carried out with the ring adapter.
^ Fit adapter (2) into the vent opening
on the dryer, and connect vent hose
(3).
^ See next page for examples.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Installation examples
Window vent
Connection to an exhaust flue
1. Window vent kit (fitted in a
1. Pipe with connection piece
(= supplied with the Miele wall vent
kit)
"plexiglass" pane)
(separate fitting instructions are
supplied with the Miele window vent
kit)
2. Adapter for flexible hose
3. Exhaust flue insulated against damp
,The ducting must not be vented
into a chimney or vent flue which is
in use, nor should it be connected to
ducting which ventilates rooms with
fireplaces.
2. Adapter for flexible hose
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
bVenting system with
If the total duct length is greater than
10 m the ring adapter is not required.
plastic piping
BFit Miele adapter (2) into the vent
Plastic piping is a good option where
the vented air has to ducted for some
distance. The smooth walls of the
pipe are less resistant to the vented
air than the walls of a flexible vent
hose, for example. Time and energy
consumption are better with plastic
piping.
opening on the dryer.
CAttach the pipe (3).
Example
^ The following items are required: . .
. . . an adapter* (dia. 100 mm)* with
rib on the inside.
. . . a wall vent kit* or window vent
kit*.
* (Miele optional accessory)
. . . Suitable plastic piping is
available from your dealer or builder’s
merchant. If a pipe diameter greater
than 100 mm is required, additional
adapters are necessary (e.g. to
increase from C 100 to 125 mm) to
connect the pipe to the dryer.
1. Wall vent kit
(Separate fitting instructions are
supplied with the Miele wall vent kit).
2. Adapter
3. Plastic piping, diameter DN 100
AThe ring adapter (1) only needs to be
fitted into the Miele adapter (2), if the
total duct length is less than 10 m.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
cConnecting directly to a wall Side view:
vent
The best method of venting the dryer
is to connect it directly to the outside
wall of a room. However, it is
necessary to insert the wall vent right
through the wall.
Because the vented air is blown
directly outside, and has only a short
distance to go, this system is very
efficient in terms of time and energy
consumption.
^ A wall pipe and a flexible foam
gasket must be used (both Miele
optional accessories).
ABefore drilling into the wall . . .
. . . please read the installation
instructions supplied with the Miele
wall pipe.
1. Wall pipe
2. Flexible foam gasket
. . . and study the following
diagrams.
View from above:
BInsert the ring adapter (1) into the
wall pipe.
CFit the foam gasket (3) on to the
connecting piece (2) on the wall pipe
and push the dryer up against the
wall.
1. Wall pipe
2. Flexible foam gasket
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation - venting
Washer dryer stack
Miele washing machine with Comfort
line angled fascia
Height of venting outlet for washer
dryer stack
Miele washing machine with straight or
sloping fascia
Stacking kit* without pull-out shelf:
C = 94.2 cm
D = 170.0 cm
Stacking kit* without pull-out shelf:
A = 94.2 cm
Stacking kit* with pull-out shelf:
C = 96.0 cm
B = 170.0 cm
D = 171.8 cm
Stacking kit* with pull-out shelf:
A = 92.8 cm
* Miele optional accessories
B = 168.6 cm
* Miele optional accessories
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Consumption data
Programme
Load
Final spin speed
Energy
Time
in a domestic washing machine
kg*
6.0
rpm
kWh
Minutes
Cottons Normal
800 (70 % residual moisture)**
3.90
3.05
2.90
2.80
2.55
107
85
81
78
71
1200
1400
1600
1800
Cottons Hand iron
6.0
800 (70 % residual moisture)**
3.00
2.20
2.05
1.95
1.70
82
61
57
55
48
1200
1400
1600
1800
Minimum iron Normal
Minimum iron Hand iron
Automatic
3.0
3.0
3.0
2.0
3.0
1000 (50 % residual moisture)**
1.35
1.20
1.75
0.15
0.30
38
33
49
3
1000
900
Woollens handcare
Smoothing
-
-
8
*
Weight of dry laundry
** EN 61121 Standard testing is carried out with the ring adapter.
All data established in accordance with EN 61121.
Before testing in accordance with EN 61121, dry a 3 kg load of cotton laundry with 70% residual
moisture as per the above standard using the Cottons Normal programme.
Consumption data can vary from the nominal values given above depending on the size of the
load, types of textiles, residual moisture levels after spinning, fluctuations in the electricity
supply and any additional options selected.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical data
Height
850 mm (adjustable +7 / -7 mm)
Height for building under
Width
820 mm
595 mm
Depth
580 mm
Depth with door open
Weight
1,060 mm
48 kg
Drum volume
100 litres
Maximum capacity
Length of connection cable
Voltage
6 kg dry weight
2 m
see data plate
see data plate
see plug
Connected load
Fuse rating (UK)
Lamp wattage
Energy consumption
Test certificates awarded
see data plate
see "Consumption data" section
Radio / TV suppression, VDE
37
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
for changing default settings
The programmable functions are
used to alter the machine's
electronics to suit changing
requirements.
Programmable functions can be
altered at any time.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Altering the residual moisture
level in the Cottons
programmes
APress the Start button and keep it
pressed in whilst carrying out steps
B-C.
BSwitch the dryer on with the
The machine is designed to dry
effectively using as little energy as
possible.
However, if you require the laundry to
be drier, it is possible to reduce the
default residual moisture level in the
Cottons programmes.
Please note that programme
durations will be longer if this option
is activated.
I-On/0-Off button.
CWait until the Start indicator lamp
comes on . . .
D. . . and then release the Start button.
ETurn the programme selector to the
Cottons Normal position.
FPressing the Start button switches
between activating and deactivating
the drier setting.
Follow steps A to G to programme
and store in memory.
– If the Drying indicator lamp is
flashing: the drier setting is
activated
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– If the Drying indicator lamp is not
flashing, the drier setting is not
activated and the residual moisture
level is on the standard default
setting.
– The programme selector is at Finish.
GSwitch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the drier setting has been selected.
^ Switch off the dryer.
The check is complete.
40
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Altering the residual moisture
level in the Minimum iron
programmes
APress the Start button and keep it
pressed in whilst carrying out steps
B-C.
BSwitch the dryer on with the
The machine is designed to dry
effectively using as little energy as
possible.
However, if you require the laundry to
be drier, it is possible to reduce the
default residual moisture level in the
Minimum iron programmes.
Please note that programme
durations will be longer if this option
is activated.
I-On/0-Off button.
CWait until the Start indicator lamp
comes on . . .
D. . . and then release the Start button.
ETurn the programme selector to the
Cottons Low temperature position.
FPressing the Start button switches
between activating and deactivating
the drier setting.
Follow steps A to G to programme
and store in memory.
– If the Drying indicator lamp is
flashing, the drier setting is
activated
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
– If the Drying indicator lamp is not
flashing, the drier setting is not
activated and the residual moisture
level is on the standard default
setting.
– The programme selector is at Finish.
GSwitch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the drier setting has been selected.
^ Switch off the dryer.
The check is complete.
41
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Activating and deactivating the APress the Start button and keep it
pressed in whilst carrying out steps
B-C.
buzzer
A buzzer sounds (at intervals for a
maximum of 1 hr) to let you know the
programme has finished.
BSwitch the dryer on with the
I-On/0-Off button.
CWait until the Start indicator lamp
The machine is delivered with the
buzzer activated but you can
deactivate it if wished.
comes on . . .
D. . . and then release the Start button.
ETurn the programme selector to the
The buzzer will still sound if there is a
fault, even if it has been deactivated.
Cottons Hand iron position.
FPressing the Start button switches
between activating and deactivating
the buzzer.
Follow steps A to G to programme
and store in memory.
– If the Drying indicator lamp is not
flashing:
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
the buzzer is deactivated
– If the Drying indicator lamp is
flashing:
– The programme selector is at Finish.
the buzzer is activated
GSwitch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
The Drying indicator lamp will show you
if the buzzer is activated.
^ Switch off the dryer.
The check is complete.
42
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Extending the cooling down
time
– If the Drying indicator lamp flashes
once:
The cooling down time will be five
miinutes longer.
The cooling down phase which takes
place before the end of a programme
can be lengthened if required. This
makes the garments easier to
handle.
– If the Drying indicator lamp flashes
twice:
The cooling down time will be ten
minutes longer.
The dryer is delivered with the
extended cooling down time option
deactivated. You can extend the
cooling down time by 5 minutes or 10
minutes.
– If the Drying indicator lamp is not
flashing:
The cooling down time is not
extended.
GSwitch the machine off with the
The option of extending the cooling
down time is available with the Cottons,
Minimum iron and Automatic
programmes.
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
Follow steps A to G to programme
and store in memory.
To check:
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
The Drying indicator lamp will show you
if the cooling down time has been
extended.
– The programme selector is at Finish.
APress the Start button and keep it
pressed in whilst carrying out steps
B-C.
^ Switch off the dryer.
The check is complete.
BSwitch the dryer on with the
I-On/0-Off button.
CWait until the Start indicator lamp
comes on . . .
D. . . and then release the Start button.
ETurn the programme selector to the
Cottons Machine iron position.
FPressing the Start button alters the
cooling down time.
43
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Changing the standard drying
level in the Minimum iron -
Normal programme
FPressing the Start button alters the
drying level.
– If the Drying indicator lamp is
flashing:
The drying level for this programme
is set at a standard level.
You have the option of changing this
to an increased drying level.
the standard drying level is
Normal+
– If the Drying indicator lamp is not
flashing, the increased drying level
is not activated and the drying level
will remain on the standard setting
The machine is delivered with the
drying level set at Normal
(
).
You can change this to Normal+ (drier
than the standard drying level).
GSwitch the machine off with the
I-On/0-Off button.
Important: the "Normal+" drying level
will work in addition to the "Altering the
residual moisture level in the Minimum
iron programmes" programmable
The setting you have selected is now
stored in memory. You can change it
again at any time.
function, if you have already set this.
To check:
Follow steps A to G to programme
and store in memory.
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
The Drying indicator lamp will show you
if the Normal+ drying level has been
set.
– The programme selector is at Finish.
^ Switch off the dryer.
APress the Start button and keep it
pressed in whilst carrying out steps
B-C.
The check is complete.
BSwitch the dryer on with the
I-On/0-Off button.
CWait until the Start indicator lamp
comes on . . .
D. . . and then release the Start button.
ETurn the programme selector to
Minimum iron - Normal.
44
Download from Www.Somanuals.com. All Manuals Search And Download.
Programmable functions
Changing the standard drying
level in the Automatic
programme
F Pressing the Start button alters the
drying level.
– If the Drying indicator lamp flashes
twice:
The drying level for this programme
is set at a standard level.
You have the option of changing this
to an increased drying level.
the standard drying level is
Normal+
– If the Drying indicator lamp is not
flashing:
the standard drying level is Hand
iron
The machine is delivered with the
drying level set at Normal
– If the Drying indicator lamp flashes
once, the drying level has not been
changed and will remain on the stan-
You can change this to Hand iron
(damper) or Normal+ (drier than the
standard drying level).
dard setting (
).
Follow steps A to G to programme
and store in memory.
GSwitch the machine off with the
I-On/0-Off button.
The setting you have selected is now
stored in memory. You can change it
again at any time.
Before you begin, first ensure that:
– The tumble dryer is switched off.
– The door is closed.
To check:
– The programme selector is at Finish.
^ Make sure the dryer is switched off,
the door is closed and the
programme selector is at Finish and
then carry out steps A to E.
APress the Start button and keep it
pressed in whilst carrying out steps
B-C.
BSwitch the dryer on with the
The Drying indicator lamp will show you
if the drying level has been changed.
I-On/0-Off button.
CWait until the Start indicator lamp
^ Switch off the dryer.
comes on . . .
The check is complete.
D. . . and then release the Start button.
ETurn the programme selector to the
Automatic position.
45
Download from Www.Somanuals.com. All Manuals Search And Download.
46
Download from Www.Somanuals.com. All Manuals Search And Download.
47
Download from Www.Somanuals.com. All Manuals Search And Download.
Alteration rights reserved/1306
M.-Nr. 06 619 190 / 01
en - GB
Download from Www.Somanuals.com. All Manuals Search And Download.
|