Operating Instructions
Condenser Dryer
T 1329 C
To prevent accidents
and machine damage
read these instructions
before
UV
installation or use.
M.-Nr. 06 057 180
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Do not repair or replace any part of
the appliance or attempt any
servicing unless specifically
recommended in these operating
instructions. Repairs to electrical
appliances should only be performed
by qualified personnel. Incorrectly
repaired machines may pose a
considerable risk to the user.
,WARNING - To reduce the risk of
fire, electric shock, or injury to
persons when using your appliance,
follow basic precautions, including
the following:
Read all instructions before using
the appliance.
Do not dry articles that have been
previously cleaned, washed,
soaked or spotted with gasoline,
dry-cleaning solvents or other
flammable or explosive substances.
They may give off vapors that could
ignite or explode.
Do not use fabric softener sheets
to eliminate static in this dryer. Best
results are achieved when a liquid
softener is used in the washer.
Do not use heat to dry articles
containing foam rubber or similarly
textured rubber-like materials, or items
containing hair spray, nail polish
remover or similar substances.
Do not allow children to play on or
in the appliance. Close supervision
is necessary when the appliance is
used near children. Always close the
door after use to prevent child hazards.
Clean the lint filter before or after
each load.
Keep the area around the air intake
(toekick) and adjacent surrounding
areas free from lint, dust and dirt.
Before this appliance is removed
for service or discarded, remove
the door to the drying compartment.
The interior of the machine should
be cleaned periodically by
qualified personnel.
Do not reach into the dryer if the
drum is moving.
Do not install or store this
appliance where it will be exposed
to the weather.
Do not place items exposed to oils
in your dryer. Items contaminated
with oils may contribute to a chemical
reaction that could cause the laundry to
catch fire.
Do not tamper
with the controls.
This dryer is intended for
residential use only!
3
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or
breakdown, grounding will reduce the
risk of electric shock by providing a
path of least resistance for electric
current.
This appliance is equipped with a cord
having an equipment grounding
conductor and a grounding plug. The
plug must be plugged into an
appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
WARNING – Improper connection
of the equipment-grounding
conductor can result in a risk of electric
shock. Contact a qualified electrician if
you are in doubt as to whether the
appliance is properly grounded.
Do not modify the plug provided
with the appliance: if it will not fit
the outlet, have a proper outlet installed
by a qualified electrician.
SAVE THESE INSTRUCTIONS
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Control panel
a e- "PROGRAMS" buttons
g "Start/Stop" button T
For selecting a drying program.
Starts and stops a program.
Interrupts a program when pressed.
b "OPTIONS" buttons
Flashes during program selection
and lights once the program starts.
For selecting a drying option.
c "DRYNESS" button
h "Door" button
For selecting the dryness level of
finished laundry.
Opens the door when the program
has finished. If the dryer is on, the
drum interior will light when the door
is opened. If the door is left open, the
light will go off after a few minutes to
save energy.
d "STATUS" display
Shows the current cycle of the drying
program.
i "On/Off" button
e "Buzzer" button
Turns power to the machine on and
off.
When selected, a buzzer will sound
at the end of a program.
f "FAULT" indicators
An illuminated indicator will alert you
if the child lock has been activated
or if a fault occurred.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
Before loading the dryer
Program recommendations
The dryer must be correctly installed
and connected before the first use.
Please refer to the "Installation
Instructions".
Normal
– Cottons and Permanent Press blends
Wrinkle-free
^ Before using for the first time clean
the drum with a cloth.
– Permanent Press:
select the Hand Iron dryness and
reduce the load size for best drying
results
Before drying, check fabric care
labels for special drying instructions.
– Delicate fabrics, such as polyester:
select the Gentle option to reduce
creasing
q Dry with normal temperature
r Dry with low temperature
(select "Gentle" option)
s Do not dry in a tumble dryer
– Pure linen and down filled items
– Do not overload the drum!
Woolens
Overloading the dryer will result in
poor drying results and wrinkling.
– Wool and wool blends
– Knitted fabrics and flannel tend to
shrink when washed and dried for
the first time. Do not overdry these
fabrics.
Smooth
– Linen
– Permanent Press (cottons, blends
and synthetics)
– To prevent discoloration, do not dry
new, dark-colored fabrics with
light-colored items.
Sturdy
– Durable Cottons and Permanent
Press
– Close zippers and tie up fabric belts
and apron ties to prevent tangles
and damage to clothing.
Fluff / 20 min / 30 min
– Do not dry items that may melt or
ignite in the dryer, such as plastics,
rubber or sneakers.
– All fabric types
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the dryer
1. Turn on the dryer and load
the laundry
2. Select a program
^ Press the "On/Off" button to turn on
the dryer.
^ Press the "Door" button to open the
door.
^ Load the laundry loosely into the
drum.
^ Make sure the lint filters are in place.
^ Close the door with a firm swing - do
not push it shut.
For best results use liquid fabric
softener when washing laundry.
Fabric softener sheet may clog the
filters and cause the dryer to
overheat.
^ Press the e or - button until the
desired program indicator lights.
To prevent fabric damage, check
that laundry will not be caught in the
closed door.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the dryer
Program
Fabric
Available drying options: Turbo, Gentle, Anti-crease
Note
Normal
Extra Dry
Multi-layer fabrics, mixed loads of
sturdy cottons, e.g. jeans, towels.
The "Extra dry" program should not be
selected for jersey materials.
Items may shrink.
More Dry
Normal
Uniform loads of cotton, e.g. sheets,
underwear, socks.
-
Knitted cotton fabrics that may shrink, If items are still damp, dry again using
e.g. jersey material or lightweight
cottons.
"More Dry".
Less Dry
Hand Iron
Cotton or linen fabrics to be left damp
for ironing.
-
If fabrics are too damp for ironing, dry
again using "Less Dry".
Rotary Iron
Cotton or linen fabrics which will be
ironed with a rotary iron.
To prevent moisture loss, roll up the
laundry until ironing.
Wrinkle-free Available drying options: Turbo, Gentle, Anti-crease
More Dry
Synthetic permanent press items,
e.g. pants and shirts.
-
Normal
Permanent press and blended fabrics,
e.g. cotton/synthetic.
Less Dry
Permanent press and blended fabrics Reduce load size for fabrics that wrinkle
requiring an ironed finish. easily.
Special Programs Available drying options: Anti-crease only available in
Fluff, Sturdy
Woolens
Delicate items which allow machine
drying.
Remove items immediately after the end
of the program while still slightly damp.
Allow items to air dry.
Smooth
Program for reducing creasing of
cotton, linen or permanent press
fabrics made of cotton, blends or
synthetics.
-
Sturdy
Fluff
For mixed loads of cotton and
permanent press items.
-
Individual items to be freshened and
fluffed with cool air.
Reduce load size.
TIMED CYCLES
20 min
Available drying options: Gentle, Anti-crease
Individual items or very small loads,
-
e.g. beach towels, swimsuits.
30 min
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the dryer
3. Select a drying option
(if needed)
OPTIONS
Turbo
Fast drying for sturdy fabrics with
increased temperature and a reduced
program length.
Gentle
For drying delicate fabrics slowly at a
lower temperature.
Anti-crease
Prevents wrinkles if laundry is not
removed immediately after the end of a
program. The drum periodically rotates
for about 1 hour.
^ A drying option can be selected or
deselected with each press of the
button.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the dryer
4. Select the dryness level
5. Select the buzzer (if desired)
The dryness level can be selected in
the "Normal" and "Wrinkle-free"
^ Press the "Buzzer" button to have a
tone beep at the end of the program.
programs. (The dryness level of the
other programs cannot be adjusted.)
Indicator light:
on = buzzer selected
off = buzzer not selected
Adjusting the buzzer volume:
– the dryer must be on
– the door closed
– a program selected
– if the "Buzzer" indicator is lit, press
the "Buzzer" button so its indicator
light goes out.
^ Press and hold the "Buzzer" button
until its indicator lights and you hear
the desired volume and tone.
^ Press the selection button until the
desired indicator illuminates.
In the "Wrinkle-free" program, only
"More Dry", "Normal" and "Less Dry" can
be selected.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the dryer
6. Start the program
7. At the end of a program
The "Anti-crease/End" indicator will light
at the end of a program and the buzzer
will sound if it was selected.
If a fault occurred, a "FAULT" indicator
will light. See "Frequently asked
questions" for details.
^ Press the "Start/Stop" button.
Once the program starts, the current
cycle of the program will be indicated
in the "STATUS" display.
^ Press the "Door" button.
^ Open the door.
^ Remove the laundry.
^ Check that the drum is empty.
^ Clean the lint filter after each use
(see "Dryer care").
^ Close the door.
^ Press the "On/Off" button to turn off
the dryer.
^ Empty the condensed water
container weekly (if not connected to
a drain).
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Using the dryer
Canceling or changing a
program
Adding or removing laundry
during a program
^ Press and release the "Start/Stop T"
button to stop the drying program.
^ Turn off the dryer using the "On/Off"
button.
To continue drying:
^ Press the "Door" button.
^ Select the new program by pressing
^ Open the door.
the e or - button.
,CAUTION - Do not touch the rear
of the drum while adding or
removing items! There is a danger of
burns due to high temperatures in
the drum.
^ Select any desired options.
^ Select a dryness level (available in
the "Normal" and "Wrinkle-free"
programs).
^ Press and release the "Start/Stop T"
button to start the new program.
^ Add or remove items.
^ Close the door.
^ Turn the dryer back on with the
"On/Off" button.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Child lock
Child lock
To deactivate the child lock
When activated, the child lock prevents Repeat steps 1. to 5.
the dryer from being operated by
locking the control panel functions.
The "Child lock" indicator will go out.
The control panel is now unlocked.
The dryer can be turned on but not
started. The "Child lock" indicator will
flash.
6. Turn off the dryer using the "On/Off"
button.
The door can be opened.
To activate the child lock
1. Make sure the dryer is turned off and
the door is closed.
2. Press and hold the "Anti-crease" and
"DRYNESS" buttons at the same time,
hold until step 5.
3. Turn on the dryer with the "On/Off"
button.
4. Press the "OPTIONS" button 3 times.
5. Release the "Anti-crease" and
"DRYNESS" buttons.
The "Child lock" indicator will flash and
the dryer is now locked.
6. Turn off the dryer using the "On/Off"
button.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer care
Cleaning the lint filter
The lint filter must be cleaned after
every program.
^ Remove the lint from the door frame
lint filter with your fingers.
^ Any lint remaining in the hollow
casing of the door can be removed
through the gap at the bottom with a
dust brush or vacuum.
^ Open the door and remove the lint
filter by gently lifting it upwards.
^ Return the lint filter and close the
door.
The lint filters (once removed from
the dryer) can be rinsed with hot
water if necessary. The filters must
be dried thoroughly before being
returned to the dryer.
^ Take the door lint filters out by turning
the knob at the filter top.
^ Wipe the lint off the filter with your
hand (do not use any sharp objects!)
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer care
Cleaning the exterior and the
control panel
,To reduce the risk of electric
shock, disconnect the dryer from the
power supply by shutting off the
power main, tripping the circuit
breaker or unplugging the power
cord before performing
maintenance.
Never use abrasive cleaners,
scouring pads, steel wool or caustic
(oven) cleaners on the dryer. They
will damage the surface.
^ The exterior and the control panel
can be cleaned with warm water and
liquid dish soap applied with a soft
sponge.
^ Wipe dry.
Cleaning the drum
^ The stainless steel surfaces of the
drum can be cleaned using a
non-abrasive stainless steel cleaner.
^ Wipe clean with a soft cloth.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer care
Emptying the condensed water
container
Depending on the installation, the
condensed water will either be pumped
to a drain or collected in the condensed
water container, located in the upper
left corner of the machine.
The container holds approximately
1 gallon of water.
The container should be emptied
weekly.
Should the container be full when the
tumble dryer is started, or if it becomes
full during normal operation:
^ Pull out the container slightly to the
right with both hands.
– The "Container" indicator will light.
– The buzzer will sound.
^ Hold the cap open while emptying
the container.
^ When the container is empty, push it
back into its opening until it clicks
into place.
^ Restart the drying program if needed.
Do not drink the condensed water!
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer care
Cleaning the condenser
Removing the condenser
^ Open the door.
,To reduce the risk of electric
shock, disconnect the dryer from the
power supply by shutting off the
power main, tripping the circuit
breaker or unplugging the power
cord before performing
maintenance.
Detergent residues, hair and lint in the
drying air can penetrate filters and clog
the condenser. Particles from the cool
air sucked in from the install location
can cause blockages.
^ Check the condenser at least twice a
year. If used often, check every 100
loads.
^ Open the access panel, located on
the lower left corner of the machine,
using the yellow tool supplied with
the machine.
^ Clean if necessary.
Hold the panel when opening it.
^ Remove the panel up and out of the
condenser access area.
^ Turn the condenser door lock down
and remove the door.
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer care
Checking the condenser
^ Hold the condenser against the light.
^ Turn the condenser lock up.
^ Look through the front and left side
(as illustrated above) of the
condenser to check for lint.
If no lint is visible:
^ Return the condenser.
If lint is visible:
^ Clean the condenser as described.
^ Pull out the condenser.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer care
Cleaning the condenser
Returning the condenser
^ Rinse the condenser along all sides
with warm water as shown in pictures
below.
^ Put the condenser back in place in
the reverse order.
Check the gasket around the front of
the condenser is flush and not
crimped.
^ To prevent leaks, make certain the
condenser is pushed in all the way
and locked in place.
^ Restore power.
^ Check the condenser for visible
soiling. Continue rinsing until the
condenser until clean.
^ Check the condenser gasket for
soiling.
Do not remove or kink the gasket!
^ Place the condenser lengthwise on a
towel to air dry.
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Dryer care
Changing the light bulb
^ Replace the light bulb with a
temperature proof bulb, available
from Miele.
,To reduce the risk of electric
shock, disconnect the dryer from the
power supply by shutting off the
power main, tripping the circuit
breaker or unplugging the power
cord before performing
The light bulb must not exceed the
maximum wattage listed on the data
plate.
^ Flip up the light bulb cover and press
it firmly until it clicks into place.
maintenance.
^ Open the door.
,Make sure the bulb cover is
securely closed to prevent a short
circuit or penetrating moisture.
The bulb cover is located along the
upper rim of the drum opening.
^ Restore power.
^ Slide a screwdriver with a wide head
underneath the side edge of the bulb
cover and twist (see illustration).
^ Flip down the bulb cover.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Guide
Remove this guide for easy reference
Please read all
instructions, especially
the "Important Safety Instructions",
before using the dryer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Guide
1.Turn on the dryer and load the
laundry
2. Select a program
^ Press the "On/Off" button to turn on
the dryer.
^ Press the "Door" button to open the
door.
^ Load the laundry into the drum. Make
sure that there is enough space in the
drum for clothes to tumble freely.
^ Press the e or - button until the
desired program indicator lights.
3. Select a drying option (if needed)
To prevent fabric damage, check
that laundry will not be caught in the
closed door.
^ A drying option can be selected or
deselected with each press of the
button.
^ Close the door with a firm swing - do
not push it shut.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Guide
4. Select the dryness level
5. Select the buzzer (if desired)
6. Start the program
^ Press the "Start/Stop" button.
7. At the end of a program
The "Anti-crease / End" indicator will
light.
^ Press "Door" and remove the laundry.
^ Clean the lint filter.
^ Press the selection button until the
desired indicator illuminates.
^ Press the "On/Off" button to turn off
the dryer.
Download from Www.Somanuals.com. All Manuals Search And Download.
Quick Guide
Program
When to use
Available drying options Turbo, Gentle, Anti-crease
Note
Normal
Extra Dry
For laundry to be folded and shelved
immediately, e.g. jeans, towels.
The "Extra Dry" program should not be
selected for jersey materials.
Items may shrink.
More Dry
Normal
For uniform loads, e.g. sheets,
underwear, socks.
-
For knitted items that may shrink, e.g. If items are still damp, dry again using
jersey material or lightweight cottons.
"More Dry".
Less Dry
Hand Iron
For items to be left damp for ironing.
-
If fabrics are too damp, dry again using
"Less Dry".
Rotary Iron
For items to be ironed with a rotary
iron.
To prevent moisture loss, roll up the
laundry until ready to iron.
Wrinkle-free Available drying options Turbo, Gentle, Anti-crease
More Dry
For items that do not require ironing,
e.g. pants and shirts.
-
Normal
For items to be hung after drying.
For items which require ironing.
Less Dry
Reduce load size for fabrics that wrinkle
easily.
Special Programs Available drying options: Anti-crease only available in Fluff, Sturdy
Woolens
Delicate items which allow machine
drying.
Take items out immediately after the end
of the program while still slightly damp.
Allow items to air dry.
Smooth
Program for reducing creasing in
delicate items.
-
Sturdy
Fluff
For mixed loads of durable items.
-
Individual items to be freshened and
fluffed with cool air.
Reduce load size.
TIMED CYCLES Available drying options Gentle, Anti-crease
20 min
30 min
Individual items or very small loads,
e.g. beach towels, swimsuits.
-
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
What if the dryer will not run?
Possible fault
Fix
The "Start/Stop" button was not
pressed.
Make sure the dryer is on. Press the
"Start/ Stop" button to begin the drying
program.
The circuit breaker tripped or the dryer Make sure the dryer is plugged in or
is unplugged.
reset the circuit breaker.
The door is not closed.
How do I prevent static cling?
Close the door properly.
Add fabric softener to laundry when washing or select the "Less Dry" setting on
the dryer.
Do not use fabric softener sheets in this dryer.
What if the drum light does not come on?
Possible fault
Fix
The bulb may be bad or burned out.
See "Changing the light bulb."
What if the "Child Lock" indicator flashes after turning the dryer on and a
program cannot be started?
Possible fault
Fix
The child lock is activated.
Deactivate the child lock. See "Child
Lock."
What if the program stops, the "Anti-crease/End" indicator lights and the
buzzer sounds?
Possible fault
Fix
The drum is empty.
Load laundry into the dryer. The dryer
will not operate when the drum is
empty. Single items should be dried
with "Sturdy" or a timed program and
dry items in the "Fluff" program.
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Frequently asked questions
What if the "Filter/Vent" fault indicator is lit?
Possible fault
Fix
The lint filter is clogged.
Clean the lint filters. See "Dryer care".
The air supply in the room is
insufficient.
Open a window or door to increase
airflow.
What if the program runs too long or stops?
Possible fault Fix
The airflow is insufficient in the area of Open a window or door to increase
the dryer.
airflow.
The lint filters are clogged.
Clean the lint filters (see "Dryer care").
The laundry was not spun sufficiently in Select a higher spin speed in the wash
the washer.
program.
The dryer is overloaded.
Reduce the load size.
Metal zippers interfere with the dryer’s Select a timed program to avoid
moisture sensors.
overdrying.
The condenser is clogged with lint or
detergent residue.
Clean the condenser periodically (see
"Dryer care").
The air vent below the door is blocked. Remove any blockages.
What if the laundry is not dry enough?
Possible fault
The load contained too many dissimilar items (size and fabric.)
What if water has collected around the drum opening?
Possible fault
This is condensed moisture from the laundry.
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Technical Service
In the event of a fault you cannot fix
yourself, please contact the Miele
Technical Service Department
PC Update
The indicator on the control panel
marked PC allows a technician to
update the dryer to make use of new
technology.
U
V
1-800-999-1360
For example, if new programs or fabrics
are developed, a service technician will
be able to modify the existing program
cycles accordingly.
1-800-565-6435
When contacting Technical Service,
please quote the model and serial
number of your appliance. They can be
found on the data plate located below
the drum opening.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTALLATION INSTRUCTIONS
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT SAFETY INSTRUCTIONS
Installation, repair and
maintenance work should be
performed by a Miele authorized
WARNING – Improper connection
of the equipment grounding
conductor can result in a risk of electric
service technician. Work by unqualified shock. Check with a qualified
persons could be dangerous and could electrician or service representative or
void the warranty.
Be sure to observe local building
codes.
personnel if you are in doubt as to
whether the appliance is properly
grounded.
Before installation, disconnect the
tumble dryer from the electrical
supply by shutting off the power main,
unplugging the power cord or tripping
the circuit breaker. Do not restore
power until the installation is complete.
Do not modify the plug provided
with the appliance! If it will not fit
the outlet, have a proper outlet installed
by a qualified electrician.
If there is any doubt concerning
installation, contact Miele’s
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or
Technical Service Department.
U
V
1-800-999-1360
breakdown, grounding will reduce the
risk of electric shock by providing a
path of least resistance for electric
current. This appliance is equipped
with a cord having an equipment
grounding conductor and a grounding
plug. The plug must be plugged into an
appropriate outlet that is properly
installed and grounded in accordance
with all local codes and ordinances.
1-800-565-6435
26
Download from Www.Somanuals.com. All Manuals Search And Download.
Caring for the environment
Disposal of the packing
materials
Disposal of an appliance
Old appliances may contain materials
that can be recycled. Please contact
your local recycling authority about the
possibility of recycling these materials.
The cardboard box and packing
materials protect the appliance during
shipping. They have been designed to
be biodegradable and recyclable.
Ensure that a discarded dryer presents
no danger to children. While being
stored for disposal remove the door to
the drying compartment.
To prevent suffocation of children,
ensure that any plastic wrappings,
bags, etc. are disposed of safely and
kept out of the reach of children.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Washer / Dryer Stack
The tumble dryer can also be placed
on top of a Miele washing machine for a
stacked installation. An appropriate
stacking kit is required. The stacking kit
is available from your Miele dealer or
the Miele Technical Service
Department.
,Installation of the stacking kit
must be performed by a Miele
authorized technician.
Height of a stacked installation
5’ 6 3/8" (168.6 cm)
(Stacking kit with a pull out shelf)
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Electrical connection
The dryer comes with a 5 ft long, 12/4
AWG cord and a NEMA 14-30 P plug.
GROUNDING INSTRUCTIONS
This appliance must be grounded.
In the event of malfunction or
breakdown, grounding will reduce
the risk of electric shock by
providing a path of least resistance
for electric current. This appliance is
equipped with a cord having an
equipment grounding conductor and
a grounding plug. The plug must be
plugged into an appropriate outlet
that is properly installed and
It should be connected to a
120/208-240 V, 15 A, 60 Hz AC power
supply. A 3 pole-4 wire grounding
power outlet (NEMA type 14-30 R) is
necessary.
EASY INSTALLATION KIT
If you do not have a dedicated 15 Amp
line for this appliance, but you have the
standard, 120/208-240 V - 30 Amp,
60 Hz AC outlet, you can use the "Easy
Installation Kit", which allows you to use
that line to connect the dryer to power.
grounded in accordance with all
local codes and ordinances.
WARNING – Improper connection of
the equipment grounding conductor
can result in a risk of electric shock.
Check with a qualified electrician or
service representative or personnel
if you are in doubt as to whether the
appliance is properly grounded.
057B for on-site outlet NEMA 10-30 R
060B for on-site outlet NEMA 14-30 R
For more information on the "Easy
Installation Kit" or if you have questions
concerning the electrical connection,
please contact:
U
1-800-999-1360
Do not modify the plug provided with
the appliance! If it will not fit the
outlet, have a proper outlet installed
by a qualified electrician.
V
1-800-565-6435
29
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Front view
a Power cord with plug
b Condensed water container
c Control panel
f Four height adjustable feet
g Optional drain hose:
An alternative to using the
condensed water container is to
drain condensed water into a sink,
standpipe or gully.
d Door (with decor option)
e Access panel to condenser
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation site
Installation beneath a counter
,Do not install the dryer in an area
where it can be blocked, e.g. behind
a door.
,When the machine lid needs to
be removed to reduce the height of
the machine, a built under spacer
kit* is necessary.
Transporting the dryer to the
installation site
It must be installed by a Miele
Service Technician.
The cover plate of the built under kit
replaces the appliance lid and
ensures electrical safety.
The rear excess end of the lid has a
handle box for transport.
^ Use the front dryer feet and the rear
excess end to transport the dryer
from the packaging base to the
installation site.
An installation manual is supplied with
the built-under spacer kit.
The electrical connection should be
near the dryer and accessible at all
times.
Extended machine feet* are
recommended at a built-in height of
more that 33 1/16" (840 mm).
^ Set the extended machine feet on a
height of 1 9/16" (40 mm).
Remove the original machine feet
and replace them with the extended
ones.
One or two filler frames* are
recommended at a niche height of
33 7/8" / 34 5/8" to 35 7/16" / 36 1/4"
(860/880 - 900/920 mm).
* (optional accessory)
An existing continuous toe kick must
be interrupted at the dryer location!
Reinstallation of the machine lid
When reinstalling the appliance lid,
check the firm fit of the cover at the rear
bracket for a safe transport of the dryer.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installation tips
Level the dryer
An airflow gap of 3/8" (10 mm) must
be provided between the machine
and the floor. This airflow gap must
not be blocked by a toekick or thick
piled carpets.
Do not install the dryer next to a
refrigerator. The warm air exhausting
from the dryer will affect the
thermostat of the refrigerator,
causing it to run continuously.
^ The dryer must be level to ensure
safe and proper operation.
^ The machine can be leveled by
turning the legs clockwise or
counterclockwise as necessary.
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Installing the decor panel
The door can be fitted with a
customized door panel (optional
accessory) to match the adjacent
cabinets.
Decor panel measures
Width . . . . . . . . . . . . . 23 1/ 4" (591 mm)
Height . . . . . . . . . . . . 24 15/16" (633 mm)
Thickness . . . . 1/16" - 3/16" (1.6 - 4.8 mm)
^ Open the door.
^ A decor panel up to 3/16" thickness
can be inserted if the frame sides are
pushed forward.
^ Insert the decor panel from above.
^ Press the frame sides onto the panel
und tighten the screws.
^ Push the top of the decor frame onto
the frame from the front and fix it
with the four screws.
^ Unscrew the 4 screws at the top of
the decor frame and pull it forward.
^ Loose the screws at the other sides
of the decor frame but do not take
them out.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
Shortening the door panel
Installation
The door panel can be shortened to
match the height of the adjacent
cabinetry.
^ Open the door.
^ To remove the door panel unscrew
the 10 screws (arrows) from the door
sheet panel.
The measure X equals the space from
the bottom of the washer door to the
bottom of the adjacent cabinet.
^ Remove the three decor bars from
the door panel by unscrewing the
screws.
Cut the bottom of the door panel with a
jigsaw according to X.
^ Cut the bottom of the door panel and
the two side decor bars by X.
Cut the side decor bars with a
hacksaw.
^ Drill four holes into the door panel to
fix the lower decor bar.
^ Install the decor bars and the door
panel.
To install a decor panel, check if it
needs to be shortened.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
External water drain
Rear dryer bottom:
When drying is in progress, condensed
water is pumped into the condensed
water container through the drain hose
at the back of the dryer.
The condensed water can be drained
directly into a drain if the machine is
installed near a sink or standpipe so
that the condensed water container
does not have to be emptied.
Drain hose length: approx. 3 ft. (1 m)
An extension hose is available as and
optional accessory.
Maximum Drain height: 4 ft. (1.2 m)
^ The lower clamps, 4, can be opened
to install the drain hose or to feed the
power cable through.
Installing the drain hose
Rear dryer top:
Do not pull or kink the drain hose
as this could damage it!
^ Use the curved guide to prevent the
drain hose from becoming kinked
(see "Front view" illustration).
Draining the condensed water into a
sink
^ Secure the hose carefully, e.g. by
tying the hose to the water tap, to
avoid damage by overflowing water.
Connection to a stand pipe
^ Insert the drain hose into the
Y-adapter of the sink.
^ Unclip the drain hose from the
clamps 1 and 2, and pull it off the
holder, 3.
35
Download from Www.Somanuals.com. All Manuals Search And Download.
Installation
If the external drain is not longer
used
^ Insert the drain hose into the holder
and secure it at the rear dryer top
(see holder).
^ Use the clamps at the dryer rear to
secure the drain hose.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
39
Download from Www.Somanuals.com. All Manuals Search And Download.
All rights reserved / 4804
M.-Nr. 06 057 180 / 04
Download from Www.Somanuals.com. All Manuals Search And Download.
|
