CH7260 Metal Pro
Auto feed Screwdriver
Instruction Manual
Congratulations on your purchase of a Muro Metal Pro Auto feeding Screwdriver! You have made an excellent choice. Muro high quality
tools and screws are the professional’s choice of automatic feed screw gun systems. Muro tools provide the successful builder and
contractor the ability to give their customers the advantages of screws with speed and convenience.
IF YOU HAVE ANY QUESTIONS OR COMMENTS ABOUT THIS OR ANY OTHER MURO TOOL, CALL US TOLL FREE AT 1-
800-665-6876
Muro tools are of high quality and are easy to use, but proper operating procedures are required for maximum efficiency and satisfaction.
Please take a few minutes to read the operational guide and safety instructions.
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
Keep your tool clean; remove dust and dirt by vacuuming or carefully blowing out regularly. Other tool service must be performed only
by qualified repair personnel: Service or maintenance performed by unqualified personnel could result in a risk of injury. Use of
unauthorized parts or failure to follow these Instructions may create a risk of electric shock or injury.
Hold tool by insulated gripping surfaces when performing an operation where the screws may contact hidden wiring or its own cord.
Contact with a “live” wire will make exposed metal parts of the tool "live" and shock the operator if in contact. Keep handles in good
condition, dry, clean, free from oil and grease. It is recommended to use rubber gloves if this may occur; this will also enable better control
Ver: 10/14/2004
1
Download from Www.Somanuals.com. All Manuals Search And Download.
Maintenance and Inspection of CH7260
For best results keep your CH7260 Metal Pro Clean and Free of dirt and debris for
smooth operation. Inspect and Blow out or vacuum it after use. Built up dust and dirt may
cause tool wear. To clean the tool, use a damp cloth or soap and water damped cloth, do not
use thinners or gasoline or other solvents that would damage the unit, or fully immerse it in
water, which may cause rusting. Bits are consumable and must be replaced if worn, bits are
specially designed for the Muro auto feed system.
Loading Screws in the CH7260 Metal Pro
Ensure that screws are loaded into the CH7260 with the Plastic strip facing
outwards per the diagram on the side of the screwdriver. The strips must be inserted as
shown to work properly i.e. only one way works, if inserted backwards, they will jam.
Generally, the correct end of the strip will be longer. Check that the free end of the strip fits
into the strip guide, Latch (hook) the first screw with the feed latch (Photo 2).
The strip guide supports the screw strip, assisting in keeping the screws in the correct
position for pick up by the bit, particularly for the last screws to be driven. The strip spring
acts to keep tension and a ratchet on the screw strip, also keeping the screws in the correct
position.
The strips must be
inserted as shown to
work properly i.e.
only one way works,
if inserted backwards,
they will jam. Latch
in the first screw.
1
Ver: 10/14/2004
3
Download from Www.Somanuals.com. All Manuals Search And Download.
It should be noted that
fasteners with large
heads
might
not
directly latch into the
screw guide easily. If
this happens, push the
feed lever over with
your
finger
while
inserting the strip of
screws to latch the
first screw before
using.
2
Removal of strips from Tool
1) Move the feed lever over slightly, and then press on the end of the feed latch as in
photo 3.
2) Move the feed lever back so it no longer centers the fastener as in Photo 4 and
release the feed latch. This frees the screw from the feed latch.
3) Then, pull the strip towards you and then out of the tool as shown in Photo 5. This
action will push over the strip tensioner spring to allow the strip to be removed easily.
3
Ver: 10/14/2004
4
Download from Www.Somanuals.com. All Manuals Search And Download.
4
After freeing the feed latch, pull the strip towards you and then out of the tool as shown
in Photo 5. This action will push over the strip tensioner spring to allow the strip to be
removed easily.
5
Ver: 10/14/2004
5
Download from Www.Somanuals.com. All Manuals Search And Download.
6
If difficulty is experienced, check that the
strip is not stuck on the feed latch. The strip
spring may be held back with one finger
(photo 6), while the strip is removed. Wiggle
the strip while withdrawing if required.
Driving Screws with the CH7260 Metal Pro Tool
1) Ensure you have the correct screws for the job, use the correct screw and version of
the tool for the application.
2) Check the motor direction switch is set to Forwards
3) If using a magnetic bit; check it frequently, preferably each time you load a strip and
clean the bit when required.
4) Ensure the screws are loaded into the CH7260 with the plastic strip facing out, (use
the screw diagram on the side of the nosepiece)
5) Make sure the first screw to be driven is latched (hooked) by the feed latch and is
in position to be driven with the longer end of the plastic into the plastic guide.
6) Turn on the motor and use the trigger lock to lock it in the on position
7) Position yourself to operate the tool, ensuring that you have footing such that you will
be able to push very firmly.
8) Push on the tool (if possible, watch to see screw is turning), increase force once the
drill point of the fastener hits the metal, push firmly until you hear the clutch
disengage and release. Firm pressure is a must for drilling self-drilling screws; do not
yield pressure until you hear the clutch release (buzz) for ½ a second. Sparks, red-hot
glow or unusual noises all indicate a possible problem. If any problem occurs flip
tool around and check the screws to ensure the screws are properly in position
before pushing again. Attempting to drive a second screw with one still in the barrel
will jam up the tool. If this type of jam does happen, push down on the nose or strip
guide to provide more room to rotate the feed lever and move and hold the feed latch
clear. Clear the loose screw with needle nose pliers, (watch the feed latch!) and
check the screws are correct before continuing.
Ver: 10/14/2004
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Driving screws with Adjustable Clutch - Tips
Factors affecting torque with self-drilling screws include: 1) Drilling speed 2)
Drilling Torque required 3) Threading Torque required to thread 4) Head seating Torque to
prevent breakage or stripping.
These factors vary with material thickness. Drilling speed must be lower for thick
material due to heat buildup and wear of drill point. Threading torque increases with
thickness. Head seating torque must be low enough to prevent fastener spin out or stripping,
in thin to moderate thickness when the head seats. Over torque can break off heads.
The correct torque setting must be high enough to drill, thread and seat the fastener but low
enough to prevent stripping or head breakage. This is quickly determined by listening to the
sound of the tool in action. The clutch buzzes when the clutch releases, this should occur
for only ½ a second at the point when the screw seats down properly.
If short buzzing intermittently is heard while driving but the screw still seats properly, the
torque setting should be increased further. The clutch is releasing, probably while threading,
which normally requires more torque than drilling.
If you drive a screw and no buzzing is heard on seating, the screw is probably spinning at the
bottom and is stripping out the newly formed threads in the metal; reduce the clutch setting
and try again. In very thin material <22 ga, using the depth control as well may be required
for satisfactory results.
Approximate settings for MK6827
Thickness of Mild steel sheet
Approx. Torque Setting
.032 inches (20 ga) …………………………..…….1
.072 inches (14 ga) ……………………………..….2.5
.125 inches (10 ga) …………………………….…...4
.190 inches (3/16) …………………………………5
________________________________________________________________
¼ - 1/2 inch Aluminum (Tek 5 screw)……………………..5
(for thicker steel – use the HITACHI W8VB driver)
Ver: 10/14/2004
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Changing the Hex Bit
The Hex bits are designed for specific screw guns such as the MK6827/HITACHI W8VB
screwdrivers. To change or insert the Hex bit, first cycle the tool against a table, use the Hex
bit change tool to hold the tool in the fully actuated position, ensure it is secure and cannot
spring out (Photo 7). Slide the Hex bit into the tool so that the shank sticks fully out of the
bottom. The Bit-retaining clip can then be attached or removed. Place the clip in the groove
and the clip against the edge of a table. Push slowly and firmly to engage clip. This clip is
important as is prevents the hex bit from accidentally hitting the feed latch, as well as
reducing problems if the bit happens to stick to a screw. Please insure that it always installed
on the bit before use. Carefully cycle the tool against table again to remove the bit change
tool to prevent damage.
Putting Bit clip on
taking Bit clip off
7
The Bit-Retaining clip is
important as is prevents the
hex bit from accidentally
hitting the feed latch, as well
as reducing problems if the
bit happens to stick to a
screw. Please insure that it
always installed on the Hex
bit before use. The adaptor
assembly is only used with
the Square and Phillips bits.
Changing the Hex Bit – Cont’d
Ver: 10/14/2004
8
Download from Www.Somanuals.com. All Manuals Search And Download.
When the bit and clip are
assembled into the CH7260, it may
then be attached to the driver tool.
Rotate the attachment to allow the
small hex end of the bit to mate
with the driver. Once mated, push
the attachment fully onto the
aluminum adaptor. Latch the hasp.
. (Tip: if more latching force is
required after a period of use, the
wire part of the hasp can be bent
with pliers to re-tension the clasp. If
very badly worn, the plastic sides
may touch and some plastic must
be removed from the metal clip side
with a blade to provide clearance
for clamping.)
For Wood applications set the
screw gun torque to Max and set
the starting depth control on the
attachment to the middle of the
adjust range and adjust attachment
depth adjustment to suit.
Hex screws are normally seated
using the torque control of the
screw gun to prevent “stripping
out” or fastener breakage. Set
starting torque per chart and adjust
torque until it seats consistently.
The depth control on the attachment
is set to “deep” to allow this per
middle photo.
Ver: 10/14/2004
9
Download from Www.Somanuals.com. All Manuals Search And Download.
General Safety Rules
WARNING: Read and understand all instructions. Failure to follow all instructions listed below may result in electric shock, fire and/or
serious personal injury.
SAVE THESE INSTRUCTIONS
??
??
??
??
??
??
Keep your work area clean and well lit. Dark areas invite accidents.
Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust.
Power tools create sparks, which may ignite dust or fumes.
Keep bystanders, children, and visitors away while operating a power tool.
Grounded tools must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances.
Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified
electrician if you are in doubt as to whether the outlet is properly grounded. If the tool should electrically malfunction or break
down, grounding provides a low resistance path to carry electricity away from the user.
Do not operate power tools under the influence of drugs, alcohol, or medication. A moment of inattention while operating a power
tools may result in serious personal injury.
Dress properly. Keep your hair, clothing, and gloves away from moving parts. Loose clothing, jewelry, or long hair can be caught
in moving parts.
Avoid accidental starting. Be sure the switch is off before plugging in. Carrying tools with your finger on the switch or plugging in
a tool that have the switch on invites an accident.
??
??
??
??
??
??
??
??
Do not overreach. Keep proper footing and balance at all times. Proper footing and balance enables better control of the tool in
unexpected situations.
Use safety equipment. Always wear eye protection. Dust mask, non-skid safety shoes, hard-hat, or hearing protection must be used
for appropriate conditions.
Do not use the tool if the switch does not turn it on or off. Any tool that cannot be controlled with the switch is dangerous and must
be repaired.
Disconnect the plug from the power source before making any adjustments, changing accessories, or storing the tool. These
preventative safety measures reduce the risk of starting the tool accidentally.
Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric
shock if your body is grounded.
??
??
Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp
edges or moving parts. Replace damaged cords immediately. Damaged cords increase the risk of electric shock.
When operating a power tool outside, use an outdoor extension cord marked "WA " or "W". These cords are rated to outdoor use
and reduce the risk of electric shock. When using an extension cord, be sure to use one heavy enough to carry the current your
product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. The smaller the
gage number, the heavier the cord.
??
??
Do not touch any metal part of the tool when drilling or driving into walls, floors or wherever live electrical wires may be
encountered. Hold the tool only by insulated grasping handles to prevent electric shock if you drill or drive into a live wire.
TOOL USE AND CARE, PERSONAL SAFETY
??
??
Use clamps or another practical way to secure and support the work to a stable platform. Holding the work by hand or against your body is
unstable and may lead to a loss of control.
Do not force the tool. Use the correct tool for your application. The correct tool will do the job better and safer if used at rate for which it is
designed.
??
??
??
Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use the tool while tired.
Store idle tools out of reach of children and other untrained persons. Tools are dangerous in the hands of untrained users.
Maintain tools, keep them clean.
??
??
Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the tools operation. If
damaged, have the tool serviced before using. Poorly maintained tools cause many accidents.
Use only accessories and screws that are recommended by Muro for your model. Accessories that may be suitable for one tool, may become
hazardous when used on another tool.
Ver: 10/14/2004
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Ver: 10/14/2004
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List for CH7260 Metal Pro Auto Feed Screw Driver Attachment
Item Part No.
Description
QTY
1. 163-10011
Slide Flame
1
1
1
1
1
1
1
1
1
2
1
1
1
1
3
1
2
1
1
1
1
1
1
2
1
1
1
1
1
2
1
1
1
1
1
1
1
3
1
2. 163-10021
3. 163-10031
4. 163-10041
5. 163-10051
6. 163-10061
7. 163-10101
8. 163-10110
9. 163-10120
10. 163-10130
11. 163-10141
12. 163-10150
13. 163-10170
14. 163-11010
15. 163-11020
16. 163-11030
17. 163-11060
18. 163-11070
19. 163-11080
20. 163-11090
21. 163-11100
22. 165-10200
23. 170-10180
24. 170-11110
25. 20-10401
26. 20-10501
27. 20-10801
28. 20-10901
29. 20-11101
30. 20-11701
31. 20-11801
32. 20-10601
33. HEX56340
34. HEX56340M
35. 20-11601
36. SQR26000
37. PHL26000
38. 163-11040
39. Manual
Adjusting Cover
Feeder Case
Feeder Cover
Slide Guide (L)
Slide Guide (R)
Stopper Plate for CH7260 (– blank)
Feed Lever Collar
Link Pin
Feed Roller
Adjusting Screw CH7200
Adjusting Dial
Feed Spring
Pan Head Machine Screw (M4x5)
Pan Head Machine Screw (M4x12)
Tapping Screw Pan (P tight) 3x6
Tapping Screw Flat Head (P tight) 3x10
Dowel Pin 5x20
Spring Pin A type 2x6
Spring Pin A type 2x18
Stainless Snap Fastener
Feed lever for CH7260
Latch Spring for CH tool
Flange Bushing for CH tool
Tape Support for CH7260
Feed latch for CH7260 Hex Tool
Strip control spring CH7260
Screw 4-40 x 1/8 Button Head Cap Screw
Screw Guide for CH7260 (-blank)
Screw 6-32 x 3/16 in long for CH7260
Washer 3mm x 6mm x .8mm steel CH7260
Extension Spring
Hex bit (no Magnet)
Hex Bit with magnet
E clip for Hex bit
Square bit for CH7260 tool
Philips bit for CH7260 Tool
Tapping Screw Pan (P tight) 3x12
Instruction Manual
Ver: 10/14/2004
12
Download from Www.Somanuals.com. All Manuals Search And Download.
CH7260 Series
options: -L (light spring for non-hex wall applications)
-R (rubber for non marring applications)
CH7261
(CH7260-1)
CH7260
Wood to Metal apps 1 1/4 to 1 ½
Inches long – minimized marring
also vertical wall hex apps where
chips can fall clear.
Special Wood to Metal for
dedicated 1 1/4 Inches (also
vertical wall hex)
CH7263
(CH7260-3)
CH7264
(CH7260-4)
Metal applications ¾ to 1 Inches
long with clearance for metal chips,
Stitching, General Hex tool.
Wood to Metal apps 3/4 to 1
Inches long – minimized marring
(also vertical wall hex where chips
can fall clear)
CH7266
(CH7260-6)
CH7265
(CH7260-5)
Special Metal apps ½ to 3/4 Inches
long, Clearance for metal chips
Metal applications: 1 1/4 to 1 ½
Inches long clearance for metal
chips, decking, etc.
Ver: 10/14/2004
13
Download from Www.Somanuals.com. All Manuals Search And Download.
|