TA3202 Owners Manual
Introduction
Thank you for choosing MTX to help reach your ultimate goal with your vehicle. Adding MTX amplifiers and
matching MTX speakers and subwoofers with StreetWires connections will put you in a better position to
hear, feel, and experience all of the music the artist intended you to hear.
Specifications
Primary Ratings:
Power Output: 50 Watts RMS x 2 Channels at 4 Ohms and ≤ 1% THD+N
Signal-to-Noise Ratio (1Watt): 78dB
Secondary Ratings
Power Output: 100 Watts RMS x 2 Channels at 2 Ohms and ≤ 1% THD+N
Power Output: 200 Watts RMS x 1 Bridged at 4 Ohms and ≤ 1% THD+N
THD+Noise (Distortion) (1Watt): ≤ .1%
Frequency Response (-3dB): 20Hz-20kHz
Maximum Input Signal: 10V
Maximum Sensitivity: 100mV
Dimensions: 9-5/8” x 12-11/16” x 2-1/2” (245mm x 325mm x 65mm)
Smart Engage™ Auto Turn-on (Patent No: US06556683)
Patented Pure N-Channel™ Technology (Patent No: US05631608, US05783970)
Patented Power Supply (US05598325)
Input Sensitivity Switch: 100mV-1V/1V-10V
Crossover: Hi, 12dB / Low, 24dB @ 85Hz, Defeatable
Features
1. Prizm EFX – All MTX amplifiers include backlit adjustment controls on top surface of product.
•
Color – The backlit controls offer unlimited colors on the display -- from RED, GREEN, or BLUE, to any
color in between.
•
EFX – You can switch Prizm EFX lighting to “pulsate” with beat of music.
2. Xtant Technology Cooling (XTC) – thermal-regulated turbo-charged intercooler, supplies fan forced cool air
evenly and constantly through tightly packed, bonded fins. Fan speed is continuously variable and controlled
by amplifier’s output load, temperature of heatsink, and transformers. Exhaust of internal heatsink is
strategically positioned to cool transformers to maintain maximum performance at all volumes.
3. Bi-Level Inputs with Smart Engage™ – All MTX amplifiers feature RCA type input connections. All MTX
amplifiers allow both high level and line level input into the RCA type input connections.
•
Low Level Input – All MTX amplifiers feature RCA type input connections. Source units with an output
signal level of 100mV–10V may be used. See “Input Sensitivity” for proper voltage level setting. Low Level
Inputs should be combined with High Level Inputs below.
•
High Level Inputs with Smart Engage™ – All MTX amplifiers allow high level inputs through RCA type
input connections using provided high level adapters. Source units with an output signal level of 100mV–10V
may be used. See “Input Sensitivity” for proper voltage level setting.
•
Smart-Engage™ Auto Turn-on is an auto turn-on circuit included within the amplifier. A remote turn-on
wire is not necessary when connecting the amplifiers high-level input to a high-powered source unit (Car
Stereo). The amplifier will automatically turn on when music is received through this type of connection.
Note: Smart Engage™ is only active on the left input.
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Speaker Wire Connections –
When installing the speaker wires, please take proper measures to protect them. For example, when
connecting the door speakers, the speaker wire should run from the amplifier’s output terminals, under the
carpet and through the factory rubber boot (loom) that protects the wires in the inner door jam. If the factory
boot cannot be used, take other measures to protect these wires. Sometimes the door has to be completely
removed to use the factory boot. If this is something that you do not feel comfortable doing, please ask a
professional to help you.
When connecting the speaker wires to the amplifier please observe the printed polarity markings on the
amplifier’s StreetWires connector. Failing to wire the speakers in proper phase could result in a loss of bass
response and/or poor overall sound quality.
These amps will have four speaker terminals, left and right positive and negative.
•
Stereo (2-Channel) Connection: This configuration is typically used with full range or high frequency
speakers. Each channel can drive a minimum of a 2-ohm load.
•
Bridged (1-Channel) Connection: This configuration is typically used with subwoofers. Both channels
combined can drive a minimum of a 4-ohm mono load for max power.
Note: Please pay attention and make sure the speakers or woofers are the correct IMPEDANCE (OHMS) BEFORE
attaching to the amplifier.
3. Power Terminals – When installing the power wires, please take proper measures to protect them as best you
can. For example, when running the power cable from the vehicle’s battery through the firewall, use a firewall
bushing for protection. Continue running the power wire through the interior of the vehicle under the carpet
and to the amplifier. If this is something that you do not feel comfortable doing, please ask a professional to
help you. Be sure to lay the power wire away from all signal cables.
When connecting the power wires to the amplifier please observe the printed markings on the amplifier’s
StreetWires power connector. Failing to wire the power cables properly could result in amplifier damage.
1. +12V: This is the main power input for the amplifier and must be connected directly to the positive terminal of
the car battery for the amplifier to operate properly. It is important that a main fuse is installed a maximum of
18” from the battery.
2. GND: This is the ground connection for the amplifier and must be connected directly to the metal chassis
of the vehicle for the amplifier to operate properly. A properly grounded amplifier can be run harder and
longer than a poorly grounded amplifier. The ground on the amplifier should be as short as possible and
be connected directly to the vehicle’s metal chassis. Do not connect to factory bolts of ANY kind. When
attaching the ground to the chassis, sand all the paint away from the contact point, a grounding block like the
StreetWires GT4 should be used whenever possible, this piece of equipment has 5 times the surface area a
normal screw has.
The gauge of the power and ground wire is often an overlooked aspect of amplifier installation. The more
power the amplifier receives, the more power it will produce. Power cables have a natural resistance, and
will lose voltage by the time the power makes its way to the amplifier. The larger gauge (diameter) wire will
hold more voltage over longer runs. Also, by having a larger diameter ground wire, the amplifier can run
more efficiently. MTX recommends using a minimum of 8 gauge power and ground cables to get the best
performance.
3. REM: This connection turns the amplifier on and off and needs to be connected to a remote Turn-on wire from
your source unit if you are using a low level input connection.
Note: When numerous amplifiers are used in the same system, look into using a relay with a separate power
wire connected to an alternative power source to take the strain off the source unit. Normal source units can
keep a constant 12 volts to only 2, maybe 3, amps. This wire should also be run on the away from the RCA
cables.
Double check all the previous connection installation steps, in particular, the speaker and power wiring.
Securely mount the amplifier. If everything is in order, reconnect the vehicles negative battery connection and
begin following the “Feature Setup and Adjustments” process.
Download from Www.Somanuals.com. All Manuals Search And Download.
Feature Setup and Adjustments
1. Selecting The Input Sensitivity Range – Before you turn on your system, you must select the proper input
sensitivity range on your amp using the button labeled INPUT SENS located in the GAIN CONTROL section of
the control panel.
•
Setting for aftermarket Source Units: Refer to your aftermarket owner’s manual for line level output
specification. If the specification is not available, please follow the instructions listed below.
X1 POSITION: 100mV – 1V (Typically for RCA Input)
•
Setting for factory (OEM) Source Units: To check the amount of voltage that is present from the source
unit, take a multi meter, or a volt/ohm meter, on the A/C setting, (range from 100mV up to 10 Volts) attach the
positive and negative leads directly to any exposed speaker. It will not matter if the polarity is correct, it will
read the same amount of voltage.
X10 POSITION: 1V – 10V (Typically for Speaker Level Input)
Note: It is important not to have the amp set up to receive a low voltage signal and give it a high voltage
signal. Doing this can cause damage to the amp.
2. Adjusting The Individual Gain Controls – Before you start setting your amp gains, be sure to defeat all “EQ’s”
(“off” position). You want to set the gain levels properly BEFORE applying any equalization.
Start with the source unit’s volume around ¾ of the way up, and the gain on the amp all the way down
(counter-clockwise). Slowly increase the gain clockwise until the speaker starts to distort. Immediately
decrease gain until the distortion goes away. This will be a good reference point on the volume control to
where the signal starts to distort. Remember every CD will be different, use common sense and constantly
listen for obvious distortion and adjust volume accordingly. The gain on the amp has nothing to do with how
much power the amp can produce, just how fast the amp puts out max power. Just like in an automobile, full
throttle is very rarely needed.
3. Adjusting the Hi, 12dB / Low, 24dB Mono @ 85Hz Switchable X-over Frequency Controls–
•
Setting for Subwoofers: First enable the electronic crossover by selecting the “ON” position of the X-
OVER switch, and then select the “L-PASS” (Low pass) position on the L-PASS/H-PASS switch. By selecting
this setting, the amp crosses the signal over at 85Hz with a 24dB/Oct roll off. Meaning the signal tapers off
fairly quickly at frequencies over 85Hz.
•
Setting for Components and Separates: First enable the electronic crossover by selecting the “ON”
position of the X-OVER switch, and then select the “H-PASS” (High pass) position on the L-PASS/H-PASS
switch. By selecting this you are giving the speakers 85Hz – 20kHz. The 12dB/Oct roll off means that the
frequencies under (lower than) the set 85Hz, will taper off at moderate slope.
•
Setting for Full Range (No Crossover): To disable the electronic crossover, select the “OFF” position of the
X-OVER switch. This setting will allow the amplifier to play all frequencies.
4. Prizm EFX – Now that you have completed adjusting all your amplifier settings, you can set the lighting effects
to you personal taste.
•
Selecting Colors: You can change the backlit colors simply by turning the Pot labeled PRIZM COLOR
located in the MTX PRIZM EFX section of the control panel left or right. Starting at the most counter-clockwise
position, the colors change from RED to GREEN and then BLUE, and then back to RED again. Any color in
between can also be chosen making unlimited selections.
•
Selecting the EFX Feature: You can switch Prizm EFX lighting to “pulsate” with beat of music. Simply
Depress the button labeled PRIZM EFX located in the in the MTX PRIZM EFX section of the control panel to
turn this feature on or off.
Download from Www.Somanuals.com. All Manuals Search And Download.
Trouble Shooting
Read this if you want to be a do-it-yourselfer or give us a call at 800-CALLMTX.
PROBLEM
CAUSE
SOLUTION
No LED indication
No +12V at remote connection
No +12V at Power connection
Insufficient ground connection
Blown power fuse
Supply +12V to terminal
Supply +12V to terminal
Verify ground connection
Replace fuse
LED on, no output
Volume on head unit off
Speaker connections not made
Gain control on amplifier off
Signal processing units off
All speakers blown
Increase volume on head unit
Make speaker connections
Turn up gain
Apply power to signal processor
Replace speakers
Output distorted
Balance reversed
Bass is weak
Head unit volume set too high
Amplifier gain set too high
Lower head unit volume
Lower amplifier gain
Speakers wired L + R reversed
RCA inputs reversed
Wire speakers with correct orientation
Reverse RCA input
Speakers wired out
phase
Not using MTX woofers
Wire with correct of phase
Buy MTX woofers
Blowing fuses
Excessive output levels
Amplifier defective
Lower volume
Return for service
Download from Www.Somanuals.com. All Manuals Search And Download.
|