HTB1
Home Theater Loudspeaker
System
1 Mitek Plaza
Winslow, IL 61089
815-367-3000
800-225-5689
21A6582
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
HTB1 Satellite/Center Channel
Driver Compliment
CENTER
FRONT
RIGHT
FRONT
LEFT
FRONT
Midrange- 3” shielded with paper cone, rubber surround
Tweeter- 1/2" Balanced dome tweeter
Frequency Response: 150Hz - 20kHz
Impedance: 8 ohms nominal
HTB1
SUBWOOFER
45
Power Handling: 75 watts RMS / 150 watts peak music
Recommended Amplifier Power: 20-75 watts RMS
Sensitivity: [email protected]/1M
LEFT
REAR
RIGHT
REAR
LISTENING AREA
Weight:
Satellite- 1.8 lbs.
Center Channel- 3.0 lbs
Dimensions:
Satellite- 5 7/8"H X 4"W X 4"D
Center Channel- 4 1/8"H X 9 5/8"W X 3 3/4"D
Figure 1- Typical loudspeaker placement in a home theater system.
HTB1 Subwoofer
Driver Compliment
Woofer- 8" high excursion woofer
Amplifier- 60 watts output
Crossover Frequency: continuously variable 50Hz-150Hz
Frequency Response: 50Hz - 150Hz
Enclosure: tuned port design
Weight: 17 lbs.
Dimensions: 12 3/4” H X 10 1/4” W X 13” D
Figure 2- Proper placement of left/center/right front speakers.
Optional Installation Accessories
A. Feet for Satellites
Included in the system are rubber feet that allow you to raise the Satellite
Speakers up off of a level surface. Simply peel each of the four feet off the
sheet and press on to the bottom of the Satellite Speaker. Repeat steps for
the remaining Satellite Speakers.
B. Feet for Center Channel
Included in the system are plastic feet that allow the Center Channel to be
angled more horizontally on top of your television monitor. If you wish to use
the feet, simply insert the knurled end of the feet into the two holes in the lower
rear of the Center Channel.
Figure 3- Improper placement of left/center/right front speakers
Download from Www.Somanuals.com. All Manuals Search And Download.
EXPLANATION OF FEATURES AND CONTROLS
WIRING AND CONNECTIONS
Turn off all power to your subwoofer and other equipment before making
any connections.
Refer to Figure A
Installation using speaker level inputs (Figure B).
1) Power Switch: This two position switch controls the power status of the sub-
woofer.
Off: Turns the unit off.
A/V Receiver or Amplifier
+ -
+ -
On: Turns the unit on regardless of whether a signal is present or not.
2) Subwoofer crossover: This rotary control adjusts a variable low pass filter to
set the upper frequency at which the output of the subwoofer begins to roll-off.
Continuously variable from 50Hz to 150 Hz, it matches the upper frequency char-
acteristics of the subwoofer to the low frequency response of the main stereo
speakers. Recommended setting: 120Hz-150Hz.
LEFT
FRONT
RIGHT
FRONT
FRONT
CENTER
SURROUND
FREQ
GAIN
FROM AMPLIFIER
L
R
POWER
50Hz 150Hz
L
R
MIN MAX
LINE IN
HI LEVEL IN
3) Line level input: These RCA phono jacks accept a line level full range signal
from the preamplifier output of a receiver or preamplifier. This full range signal is
processed and amplified to power the subwoofer.
FUSE 1A/250V
+
-
ON
1A 250V
4) Speaker level input: These spring loaded terminals for speaker wire accept a
stereo, speaker level, full range signal from a receiver or power amplifier. This
signal is processed and amplified to power the subwoofer.
CENTER
FRONT
OFF
120 VAC
100 WATTS
60 HZ
HTB1
Made In China
5) Fuse: For continued protection replace fuse with same type and size listed.
6) Level control: This rotary control adjusts the level of the subwoofer and is used
to balance its volume with that of the main stereo speakers.
7) Status LED: This light emitting diode shows the status of the subwoofer elec-
tronics. "Red" indicates that the amplifier is plugged in and the power switch is
on.
-
+
-
+
LEFT
REAR
RIGHT
REAR
FIGURE B
Installation with A/V amplifiers and receivers that have 5.1 channel line level
output (Figure C).
Use an RCA "Y" adaptor to connect both line level inputs.
�
�
�
�
�
OUTPUTS
A/V Receiver or Amplifier
����
����
��������������
SUB
�
FREQ
GAIN
FROM AMPLIFIER
L
�
�����
FRONT
CENTER
SURROUND
�
�
�����������
R
�������
���� ������
POWER
50Hz 150Hz
�������
L
R
MIN MAX
LINE IN
HI LEVEL IN
FUSE 1A/250V
�������������
ON
1A 250V
+ -
+ -
�
+
-
��
OFF
�� ����
�
CENTER
FRONT
120 VAC
100 WATTS
60 HZ
RIGHT
FRONT
LEFT
FRONT
���
HTB1
�������
���������
�����
Made In China
-
+
-
+
����
�������������
RIGHT
REAR
LEFT
REAR
FIGURE C
��������
Download from Www.Somanuals.com. All Manuals Search And Download.
|