Operator’s Manual
Snow Boss 550
(H623D)
Snow Boss 750
(H633E)
IMPORTANT: Read safety rules and instructions carefully before operating equipment.
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-9722.
WHITE OUTDOOR PRODUCTS COMPANY. P.O. BOX 361131 CLEVELAND, OHIO 44136-9722
770-10014A
(6/99)
PRINTED IN U.S.A.
FORM NO.
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
This Warning symbol points out important safety instructions which, if not followed, could endanger the
personal safety and/or property of yourself and others. Read and follow all instructions in this manual
before attempting to operate your snow thrower. Failure to comply with these instructions may result in
personal injury. When you see this symbol, heed its warning.
DANGER: Your snow thrower was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. Failure to observe the following safety instructions could result in serious injury
or death.
•
•
•
Use a grounded three wire plug-in for all units with
electric drive motors or electric starting motors.
TRAINING
•
Read this operators manual carefully in its entirety
Adjust collector housing height to clear gravel or
crushed rock surface.
before attempting to assemble or operate this
machine. Be completely familiar with the controls
and the proper use of this machine before operating
it. Keep this manual in a safe place for future and
regular reference and for ordering replacement
parts.
Never attempt to make any adjustments while
engine is running (except where specifically
recommended by manufacturer).
•
•
Let engine and machine adjust to outdoor
temperature before starting to clear snow.
•
Never allow children under 14 years old to operate
a snow thrower. Children 14 years old and over
should only operate snow thrower under close
parental supervision. Only persons well acquainted
with these rules of safe operation should be allowed
to use your snow thrower.
Always wear safety glasses or eye shields during
operation or while performing an adjustment or
repair, to protect eyes from foreign objects that may
be thrown from the machine in any direction.
•
No one should operate this unit while intoxicated or
while taking medication that impairs the senses or
reactions.
Keep the area of operation clear of all persons,
especially small children and pets.
OPERATION
•
Do not put hands or feet near or under rotating
•
•
parts. Keep clear of discharge opening and auger at
all times.
Exercise caution to avoid slipping or falling,
especially when operating in reverse.
•
Exercise extreme caution when operating on or
crossing gravel drives, walks, or roads. Stay alert
for hidden hazards or traffic. Do not carry
passengers.
PREPARATION
•
Thoroughly inspect the area where the equipment is
to be used and remove all door mats, sleds, boards,
wires and other foreign objects.
Disengage all clutches and shift into neutral before
starting engine.
•
After striking a foreign object, stop the engine,
remove wire from spark plug, and thoroughly
inspect the snow thrower for any damage. Repair
the damage before restarting and operating the
snow thrower.
•
•
Do not operate equipment without wearing
adequate winter outer garments. Do not wear
jewelry, long scarfs or other loose clothing which
could become entangled in moving parts. Wear
footwear which will improve footing on slippery
surfaces.
Before working with gasoline, extinguish all
cigarettes and other sources of ignition. Check the
fuel before starting the engine. Gasoline is an
extremely flammable fuel. Do not fill the gasoline
tank indoors, while the engine is running, or until
engine has been allowed to cool at least two
minutes. Replace gasoline cap securely and wipe
off any spilled gasoline before starting the engine as
it may cause a fire or explosion.
•
•
If the snow thrower should start to vibrate
abnormally, stop the engine and check immediately
for the cause. Vibration is generally a warning of
trouble.
Stop engine whenever you leave the operating
position, before unclogging the collector/impeller
housing or discharge guide, and making any
repairs, adjustments, or inspections. Never place
your hand in the discharge or collector openings.
Use a stick or wooden broom handle to unclog the
discharge opening.
•
•
Take all possible precautions when leaving the unit
unattended. Disengage the collector/impeller, shift
into neutral, stop the engine, and remove the key.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
When cleaning, repairing, or inspecting, make
certain the auger, impeller and all moving parts
have stopped. Disconnect spark plug wire and keep
away from plug to prevent accidental starting.
Do not run engine indoors, except when starting
engine and transporting snow thrower in or out of
building. Open doors. Exhaust fumes are
dangerous.
Do not clear snow across the face of slopes.
Exercise extreme caution when changing direction
on slopes. Do not attempt to clear steep slopes.
Never operate snow thrower without guards, plates,
or other safety protection devices in place.
Never operate snow thrower near glass enclosure,
automobiles, window wells, drop off, etc., without
proper adjustments of snow thrower discharge
angle. Keep children and pets away.
Do not overload machine capacity by attempting to
clear snow at too fast a rate.
Never operate the machine at high transport speeds
on slippery surfaces. Look behind and use care
when backing.
Never direct discharge at bystanders or allow
anyone in front of unit.
Disengage power to collector/impeller when
transporting or not in use.
•
•
•
Use only attachments and accessories approved by
the manufacturer of snow thrower (such as wheel
weights, counter weights, cabs, etc.).
Never operate the snow thrower without good
visibility or light. Always be sure of your footing and
keep a firm hold on the handles. Walk, never run.
Muffler and engine become hot and can cause a
burn. Do not touch.
MAINTENANCE AND STORAGE
•
Check shear bolts, engine mounting bolts, etc., at
frequent intervals for proper tightness to be sure
equipment is in safe working condition.
Never store the machine with fuel in the fuel tank
inside a building where ignition sources are present,
such as hot water and space heaters, clothes
dryers, and the like. Allow engine to cool before
storing in any enclosure.
Always refer to operators manual instructions for
important details if snow thrower is to be stored for
an extended period.
Run machine a few minutes after throwing snow to
prevent freeze up of collector/impeller. Check clutch
controls periodically to verify they engage and
disengage properly and readjust if necessary. Refer
to operators manual for adjustment instructions.
•
•
•
•
•
•
•
•
•
Your Responsibility
Restrict the use of this power machine to persons who read, understand and follow the warnings and
instructions in this manual and on the machine. Some of the safety labels on the equipment are
reproduced below. Take a moment to study these labels before operating the unit. Always maintain
safety while operating or servicing the equipment.
A W A N Y G .
F E E T
A U G N E G R
F R O M J U N I R Y D
C L O T A H N I D
H A N D S K ,
WARNING
-
R
A V O I
1. STOP ENGINE BEFORE REMOVING
DEBRIS AND SERVICING UNIT.
2. KEEP CLEAR OF IMPELLER WHILE
ENGINE IS RUNNING.
SHUT OFF ENGINE
BEFORE
UNCLOGGING
3.
NEVER DIRECT DISCHARGE AT
BYSTANDERS OR WINDOWS OR
ALLOW ANYONE IN FRONT OF
UNIT.
DISCHARGE CHUTE.
4. THOROUGHLY INSPECT THE AREA
WHERE THE EQUIPMENT IS TO BE
USED AND REMOVE ALL DOOR
MATS, SLEDS, BOARDS, WIRES AND
OTHER FOREIGN OBJECTS.
D A N G E R
5. REFER TO OWNERS MANUAL FOR
FULL INSTRUCTIONS.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: LOOSE PARTS
The snow thrower is shipped with following loose parts in the carton. Please remove all loose parts from the carton
before discarding it. See Figure 1 to identify the parts noting that these parts may be referred to again in the
following sections of this manual. Part numbers are shown in parentheses.
AUGER SHEAR BOLTS
The augers are secured to the auger shaft with two shear bolts and
Shear Bolts
(710-0890A)
hex lock nuts. If you hit a foreign object or ice jam, the snow thrower
is designed so that the bolts may shear. Two replacement shear
bolts and nuts are provided for your convenience. Store in a safe
place until needed.
Hex Lock Nuts
(712-0429)
IMPORTANT: NEVER replace the auger shear bolts with standard
hex bolts. Any damage to the auger gearbox or other components
as a result of doing so will NOT be covered by your snow thrower’s
warranty.
Figure 1
SECTION 3: ASSEMBLING YOUR SNOW THROWER
NOTE: Any reference in this manual to the left or right
side of the snow thrower is observed from the
operator’s position.
•
Raise the upper handle assembly until it locks over
the lower handle. See Figure 2 and Figure 3.
Look at the lower rear of snow thrower frame to be
sure both cables are aligned with cable roller
guides.
Secure the upper handle and lower handle with the
two plastic wing knobs, cupped washers and
carriage bolt (eyebolt on the left side)previously
removed. See Figure 3.
•
IMPORTANT: Make any final adjustments as instructed
later on in this section BEFORE operating your snow
thrower. Failure to follow the instructions may cause
damage to the snowthrower.
•
•
Remove screws from the top sides and ends of the
shipping crate.
•
Set panel aside to avoid tire punctures or personal
injury.
Hex Nut
•
•
•
Remove and discard plastic bag that covers unit.
Roll unit out of crate.
Remove the lower two plastic wing knobs, cupped
washers and carriage bolt (eyebolt on the left side)
from the lower handle. See Figure 2.
Connector
Eyebolt
Wing Knobs
Figure 3
Eyebolt
•
•
Adjust the eyebolt on the chute directional control
so the rod does not come into contact with the
engine by moving the hex nut against the handle (if
necessary). Retighten the wing nut to secure the
directional control in this position.
Slide the connector down over the end of the lower
shift rod. See Figure 3. Tap the connector until it
locks on the lower shift rod.
Wing Knobs,
Washers
and Bolts
Figure 2
5
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTE: If the connector is not properly assembled, the
shift rod will pivot and you will not be able to change
speeds or change directions.
•
Recheck the adjustment before retightening the
jam nut against the cable.
Skid Shoe Adjustment
•
If not already attached, slip the cables that run from
the handle panel to the chute into the cable guide
located on top of the engine. See Figure 4.
The space between the shave plate and the ground can
be adjusted by repositioning the skid shoes found on
either side of the snow throwers auger housing. For
close snow removal, place skid shoes in the low
position. Use middle or high position when area to be
cleared is uneven. See Figure 6.
Cable Guide
Figure 4
•
•
Unwrap the headlight wire which is attached to the
headlight, beneath the handle panel. Wind the
headlight wire around the right handle until excess
slack is removed.
Plug the wire from the headlight into the wire lead
coming from the right side of the engine, beneath
the fuel tank.
Skid
Shoes
Final Adjustments
Hex Nuts
Auger Control Adjustment
Figure 6
Check the adjustment of the auger control as follows:
•
•
Push forward on the auger control (Refer to Figure
7) until the small rubber bumper contacts the upper
handle. There should be slack in the cable.
Release the auger control. The cable should be
straight. Make certain you can depress the auger
control against the left handle completely.
IMPORTANT: It is NOT recommended that this snow
thrower be operated on a gravel surface, as loose
stones can be easily picked up and thrown by the
machine. If you must operate on a gravel surface,
ALWAYS adjust the skid shoes into the HIGH position
to allow the shave plate maximum clearance.
If adjustment is necessary, proceed as follows:
Adjust skid shoes as follows:
•
Loosen the jam nut and thread the cable in (for less
slack) or out (for more slack) as necessary. See
Figure 5.
•
Loosen, but do NOT remove, the three hex nuts
which fasten the skid shoe to the auger housing.
•
Raise or lower the skid shoe to desired position.
NOTE: Make certain the entire base of both skid shoes
are against the ground to avoid uneven wear on the
skid shoes. When one side does wear out, the skid
shoes are reversable.
•
•
Retighten the hex nuts loosened earlier.
“Z” End
Jam Nut
Repeat this adjustment on the skid shoe found on
the opposite side of the snow thrower.
Tire Pressure Adjustment
The tires are over-inflated for shipping purposes.
Check tire pressure and reduce to between 15 psi and
20 psi.
Auger Control Cable
Figure 5
NOTE: If the tire pressure is not equal in both tires, the
unit may pull to one side or the other.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
in need of adjustment and you should NOT operate the
machine before completing the adjustment as follows:
Traction Control and Shift Lever Adjustment
To check the adjustment of the traction control and shift
lever, proceed as follows:
•
Loosen the jam nut on the traction control cable
and UNTHREAD the cable one full turn.
Recheck the adjustment.
Retighten the jam nut to secure the cable when
correct adjustment is reached.
•
Move the shift lever into sixth (6) position.
a. With the traction control (refer to Figure 7 in
Section 4 of this manual) released, gently
push the snow thrower forward, then pull it
back. Disregarding the overall weight of the
snow thrower, the machine should otherwise
move freely.
•
•
If the machine can be moved freely both forward and
rearward when the traction control fully depressed,
proceed as follows:
b. Engage the traction control, and attempt to
move them machine both forward and
rearward. You should experience resistance
as the wheels should not be turning.
•
•
•
Loosen the jam nut on the traction drive cable and
THREAD the cable in one full turn.
Recheck the adjustment and repeat adjustment as
necessary.
Retighten the jam nut to secure the cable when
correct adjustment is reached.
•
Move the shift lever into the fast reverse (R2)
position and repeat the previous steps (a & b).
If you experienced resistance either when repositioning
the shift lever from 6 to R2 or when attempting to move
the machine forward or rearward with the traction
control released, your snow thrower’s traction control is
NOTE: If you are uncertain that you have reached the
correct adjustment, refer to Traction Control
Adjustment in Section 6 of this manual.
SECTION 4: KNOW YOUR SNOW THROWER
IMPORTANT: Always release tractional control before
changing speeds.
Traction Control /
Auger Control Lock
Headlight
The headlight is on whenever the engine is running.
Auger
Control
Shift
Chute
Tilt
Control
Lever
Shift Lever
The shift lever is located in the center of
the handle panel and is used to
determine both ground speed and
direction of travel. It can be moved into
any of eight positions.
Forward
Your snow thrower has six forward (F)
speeds. Position number one (1) is the
slowest. Position number six (6) is the
fastest.
Chute Directional
Control
Figure 7
Reverse
Traction Control / Auger Control Lock
The traction control is located on the right handle.
Squeeze the traction control to engage the wheel drive.
Release to stop.
Your snow thrower has two reverse (R)
speeds. R1 is the slower, while R2 is the
faster of the two.
IMPORTANT: Always release tractional control before
changing speeds.
This same lever also locks the auger control so you
can turn the chute directional control without
interrupting the snow throwing process. If the auger
control is engaged along with the traction control, the
operator can release the auger control (on the left
handle) and the augers will remain engaged. Release
the traction control to stop both the augers and wheel
drive (auger control must also be released).
Auger Control
The auger drive clutch is located on the left handle.
Squeeze the clutch grip to engage the augers. Release
to stop the snow throwing action. (Traction control must
also be released.)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
Chute Directional Control
The chute directional control is located on left side of
the snow thrower.
Primer
Choke
To change the direction in which snow is thrown, turn
chute directional control as follows:
•
•
Crank clockwise to discharge to the left.
Crank counterclockwise to discharge to the right.
Chute Tilt Control
The distance snow is thrown can be adjusted by
adjusting the angle of the chute assembly. Move the
chute tilt control forward to decrease the distance,
toward the rear to increase.
Rope
Starter
Handle
Ignition Key
Throttle
Control
Figure 8
Fuel Shut-off Valve
Closed
The fuel shut-off valve, located
Safety Ignition Key
The safety ignition key must be fully inserted in the
switch before the unit will start. Remove the ignition key
when snow thrower is not in use.
under fuel tank, controls fuel flow
from the tank. Always make certain
it is in the Open (vertical) position
before attempting to start the engine.
Open
IMPORTANT: Do NOT attempt to turn the key.
Throttle Control
The throttle control is located on the engine. It regulates
the speed of the engine.
SECTION 5: OPERATING YOUR SNOW THROWER
are not certain. If your house wiring system is not a
Gas And Oil Fill-up
three-wire grounded system, do not use this
electric starter under any conditions. If your system
is grounded and a three-hole receptacle is not
available at the point your starter will normally be
used, one should be installed by a licensed
electrician.
IMPORTANT: Although your snow thrower comes
shipped with oil already in the engine, you MUST check
the engine oil level as instructed in the separate engine
manual packed with your unit BEFORE starting the
engine for the first time. Read instructions carefully
Service the engine with gasoline and oil as
instructed in the separate engine manual packed with
your snow thrower. Read instructions carefully.
When connecting the power cord, always connect cord
to starter on engine first, then plug the other end into a
three-hole grounded receptacle.
When disconnecting the power cord, always unplug the
end from the three-hole grounded receptacle first.
WARNING: Never fill fuel tank indoors,
with engine running or while engine is
hot. Do not smoke when filling fuel tank.
To Start Engine
Electric Starter
IMPORTANT: If unit shows any sign of motion (traction
or augers) with the controls disengaged, shut engine off
immediately. Readjust as instructed under the heading
Final Adjustments in Section 3 of this manual.
WARNING: The electric starter is
equipped with a three-wire power cord
and plug, and is designed to operate on
•
•
Attach spark plug wire to spark plug.
Make certain the fuel shut-off valve is in the open
(vertical) position.
Make certain that both the auger control and the
traction control are in the disengaged (released)
position.
120 volt AC household current. It must be properly
grounded at all times to avoid the possibility of
electric shock which may be injurious to the
operator. Follow all instructions carefully.
Determine that your house wiring is a three-wire
grounded system. Ask a licensed electrician if you
•
8
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
•
Move throttle control up to FAST position. Insert
ignition key into slot. See Figure 8. Be certain it
snaps into place. Do not turn the key.
Rotate choke knob to FULL choke position (cold
engine start). If engine is warm, place choke in
OFF position instead of FULL.
Electric Start Only: Connect power cord to switch
box on engine. Plug the other end of power cord
into a three-hole, grounded 120 volt AC receptacle.
Recoil Start Only: Push primer button two or three
times when using recoil starter. If engine is warm,
push primer button once only. See Figure 8.
cover in the area of the control levers. Also, move
control levers back and forth several times. Leave
throttle control lever in the STOP or OFF position.
Leave choke control in the FULL choke position.
To Engage Drive
•
With the engine running near top speed, move shift
lever into one of the six FORWARD positions or two
REVERSE positions. Select a speed appropriate
for the snow conditions that exist.
NOTE: Use the slower speeds until you are familiar
with the operation of the snow thrower.
NOTE: Always cover vent hole in primer button when
•
Squeeze the traction control against the right
handle and the snow thrower will move. Release it
and the drive motion will stop.
pushing. Additional priming may be necessary for first
start if temperature is below 15oF.
•
•
Electric Start: Do NOT prime engine. Push starter
button on top of the engine to crank the engine.
When engine starts, release starter button.
Recoil Start: Grasp starter handle (see Figure 8)
and pull rope out slowly, until it pulls slightly harder.
Let rope rewind slowly. Pull starter handle rapidly.
Do not allow handle to snap back. Allow it to rewind
slowly while keeping a firm hold on the starter
handle.
IMPORTANT: NEVER move shift lever without first
releasing the traction control. Doing so will cause
premature wear to drive system’s friction wheel rubber.
To Engage Augers
To engage the augers and start the snow throwing
action, squeeze the auger control against the left
handle.
•
As engine warms up and begins to operate evenly,
rotate choke knob slowly to OFF position. If engine
falters, return to FULL choke, then slowly move to
OFF position.
To disengage power to the augers, release both the
auger control and the traction control, if engaged,
NOTE: The auger control can also be locked so you
can turn the chute directional control without
interrupting the snow throwing process. Refer to
Traction Control/ Auger Control Lock in Section 4 of this
manual.
To Stop Engine
•
Run engine for a few minutes before stopping to
help dry off any moisture on the engine.
To help prevent possible freeze-up of starter,
proceed as follows:
Electric Starter: Connect power cord to switch box
on engine, then to 120 volt AC receptacle. With the
engine running, push starter button and spin the
starter for several seconds. The unusual sound
made by spinning the starter will not harm engine
or starter. Disconnect the power cord from recepta-
cle first, and then from switch box.
•
Tire Chains (Optional Equipment)
Tire chains should be used whenever extra traction is
needed. See your local White Outdoor dealer for
information regarding tire chains and other optional
accessories for your snow thrower.
Operating Tips
NOTE: Allow the engine to warm up for a few minutes
as the engine will not develop full power until it reaches
operating temperature.
Recoil Starter (Optional Instructions): With
engine running, pull starter rope with a rapid, con-
tinuous full arm stroke three or four times. Pulling
the starter rope will produce a loud clattering
sound, which is not harmful to the engine or
starter.
To stop engine, remove the ignition key. Do not turn
key. Disconnect the spark plug wire from the spark
plug to prevent accidental starting while equipment
is unattended.
WARNING: Temperature of muffler and
surrounding areas may exceed 150oF.
Avoid these areas.
•
•
Set the skid shoes 1/4" below the shave plate for
normal usage. The skid shoes may be adjusted
upward (to lower the shave plate) for hard-packed
snow. Adjust downward (to raise the shave plate)
when using on gravel or crushed rock.
NOTE: Do not lose ignition key. Keep it in a safe place.
Engine will not start without the ignition key.
•
•
Remove snow immediately after it falls.
Discharge snow downwind whenever possible.
•
Wipe all snow and moisture from the carburetor
9
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Slightly overlap each previous cleared path.
Follow the precautions found under the heading To
Stop Engine to prevent possible freeze-up.
•
Clean the snow thrower thoroughly after each use.
SECTION 6: MAKING ADJUSTMENTS
WARNING: NEVER attempt to clean chute
or make any adjustments while engine is
running.
Traction Control Adjustment
Refer to the information found under the heading Final
Adjustments in Section 3 of this manual to adjust the
traction control. If you are uncertain that you have
reached the correct adjustment, proceed as follows:
Chute Assembly Adjustment
The distance snow is thrown can be adjusted by
adjusting the angle of the chute assembly. Refer to
Chute Tilt Control in Section 4 of this manual.
WARNING: Drain the gasoline out of your
snow thrower’s engine, of place a piece
of plastic film under the gas cap to avoid
spillage BEFORE beginning to perform
this adjustment.
Chute Directional Control
Support Bracket Adjustment
•
•
Tip the snow thrower forward, allowing it to rest on
the auger housing.
Remove the frame cover underneath the snow
thrower by removing sixself-tapping screws.
If the spiral at the base of the chute directional control
isn’t fully engaging with the notches in the lower chute
assembly, the support bracket can be adjusted inward
or outward as follows:
With the traction control released, there must be
clearance between the friction wheel and the drive plate
in all positions of the shift lever.
•
Loosen, but do NOT remove the two hex nuts
which secure the chute directional control support
bracket to the snow thrower housing. See Figure 9.
With the traction control engaged, the friction wheel
must contact the drive plate. See Figure 10.
Friction
Wheel
Spiral
Gear Shaft
Hex Nuts
Support Bracket
Figure 9
Drive
Plate
•
Adjust the support bracket inward or outward so
that the spiral is fully engaged in the notches on the
chute before retightening the hex nuts.
Figure 10
Skid Shoe Adjustment
The space between the shave plate and the ground can
be adjusted by raising or lowering the skid shoes. Refer
to Skid Shoe Adjustment in Section 3 of this manual.
If adjustment is necessary:
•
•
•
Loosen the jam nut on the traction drive cable and
thread the cable in or out as necessary.
Retighten the jam nut to secure the cable when
correct adjustment is reached.
Auger Control Adjustment
Refer to the information found under the heading Final
Adjustments in Section 3 of this manual to adjust the
auger control.
Reassemble the frame cover.
NOTE: If you placed plastic film under the gas cap, be
certain to remove it before operating the snow thrower.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: Make certain to check for correct
adjustment of the shift rod as instructed under the
heading Final Adjustments in Section 3 of this manual,
before operating the snow thrower.
Shift Rod Adjustment
To adjust the shift rod, proceed as follows.
•
Remove the hairpin clip and slide the connector up
to separate the upper shift rod from the lower shift
rod. See Figure 11.
Drive Wheels
The wheels may be adjusted for two different methods
of operation. The adjustment is made by placing the
click pins in one of two different holes on the right side
of the unit. See Figure 12.
Shift Lever
Ferrule
Inside Hole
in Axle
Connector
Upper Shift Rod
Hairpin
Clip
Click Pin
in Outside Hole
Shift Arm
Figure 12
One Wheel Driving—Insert the click pin only
through the outside hole of the axle (NOT the rim)
on the right side of the snow thrower. This position
gives power drive to the left wheel only, making the
unit easier to maneuver.
Lower Shift Rod
Figure 11
•
•
Place shift lever in sixth (6) position.
Both Wheels Driving—Insert the click pin through
the hole in the hub of the rim and the INSIDE hole
on the snow thrower’s right axle. This position is
good for heavy snow as there is power drive in both
wheels.
Rotate the shift arm counterclockwise (from the
operator’s position) as far as it will go.
Thread the upper shift rod downward until the
elbow on its lower end aligns with the hole found in
the lower shift rod.
•
•
IMPORTANT: NEVER operate the snow thrower with the
click pin inserted through both the RIM and the
OUTSIDE HOLE in the axle. Doing so can result in
serious damage to the drive system.
Reconnect the upper shift rod to the lower shift rod
by reinserting the hairpin clip removed earlier and
sliding the connector back down into place.
SECTION 7: MAINTAINING YOUR SNOW THROWER
Traction Control / Auger Control Lock
Lubrication
The cams on the ends of the control rods which
interlock the traction drive and auger drive clutches
must be lubricated at least once a season or every
twenty-five hours of operation. The cams can be
accessed beneath the handle panel. Use a multi-
purpose automotive grease.
WARNING: Disconnect the spark plug wire
and ground against the engine before
performing any maintenance proceedures.
Engine
Refer to the seperate engine manual packed with your
unit for all engine lubrication instructions.
Gear Shaft
Lubricate the gear shaft with 6-n-1 grease at least once
a season or after every 25 hours of operation (available
at auto parts stores, or order part number 737-0170).
Refer to Figure 10.
IMPORTANT: When following instructions in separate
engine manual for draining oil, be sure to protect frame
to avoid oil dripping onto transmission parts.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Wheels
Oil or spray lubricant into plastic wheel bearings
Chute Directional Control
The spiral on the end of the chute directional control
and the base of the discharge chute itself should be
lubed with multi-purpose automotive grease once a
season. See Figure 15.
•
inside the wheel hubs at least once a season.
Remove wheels, clean and coat axles with a multi-
purpose automotive grease. See Figure 13.
Lube Spiral
and Chute Base
Click Pin
Axle
Oil or use Spray Lubricant
Figure 13
Figure 15
Auger Shaft
At least once a season, remove the shear bolts on
Gear Case
•
The gear case is equipped with a grease fitting on the
left housing and should be lubricated with Shell Alvania
grease EPR00, part number 737-0168 every 25 hours.
See Figure 16.
the auger shaft. Oil or spray lubricant inside and on
the plastic bearings on the shaft. See Figure 14.
Shear Bolts
Plastic Bearings
Figure 14
Vent Plug
Drive and Shifting Mechanism
Lube Fitting
Figure 16
At least once a season or after every 25 hours of
operation, remove rear cover. Lubricate any chains,
sprockets, gears, bearings, shafts, and shifting
mechanism at least once a season. Use engine oil or a
spray lubricant. Avoid getting oil on rubber friction
wheel and aluminum drive plate. Refer to Figure 10.
IMPORTANT: Do not overfill the gear case. Damage to
the seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.
SECTION 8: SERVICE
WARNING: Disconnect the spark plug wire
and ground against the engine before
performing any repairs or maintenance.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary. To
remove the skid shoes, proceed as follows:
Engine
Refer to the separate engine manual packed with your
unit for all engine related maintenance procedures.
•
Remove the six carriage bolts, bell washers and
hex nuts which attach them to the snow thrower.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
•
Reassemble new skid shoes with the six carriage
bolts, bell washers (cupped side goes against skid
shoes) and hex nuts. Make certain the skid shoes
are adjusted to be level.
•
Unhook the idler spring from the hex bolt on the
auger housing. See Figure 19.
Friction Wheel
To remove shave plate, remove the carriage bolts,
belleville washers and hex nuts which attach it to the
snow thrower housing. Reassemble new shave plate,
making sure heads of the carriage bolts are to the
inside of the housing. Tighten securely.
Frame
Belt Removal And Replacement
Support
Bracket
WARNING: Disconnect the spark plug
wire from the spark plug and ground.
Auger Belt
Auger Belt
•
Remove the plastic belt cover by removing the two
self-tapping screws. See Figure 17.
Idler
Spring
Support
Bracket
Spring
Auger
Pulley
Auger
Housing
Figure 19
Belt
Cover
•
Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 20.
Friction Wheel
Friction
Wheel Disc
Drive Belt
Stop Bolt
Self-Tapping Screws
Figure 17
•
•
Drain the gasoline from the snow thrower.
Tip the snow thrower forward so that it rests on its
auger housing and remove six self-tapping screws
from the frame cover underneath the snow thrower.
Roll the belt off the engine pulley. See Figure 18.
Auger Pulley
Support Bracket
•
Figure 20
Drive
Belt
NOTE: Loosening the six nuts that connect the frame to
Auger Pulley
the auger housing may aid in belt removal.
Engine
Pulley
•
Lift the auger belt from the auger pulley, and slip
belt between the support bracket and the auger
pulley. See Figure 19. Repeat this step for the front
auger belt.
Auger
Belt
•
Replace the auger drive belt by following
instructions in reverse order.
Engine
Pulley
Drive Belt
•
Follow the first four steps of the instructions for
Idler
Pulley
serviceing the auger belt..
Pull idler pulley up, and lift belt off engine pulley and
friction wheel disc. See Figure 18.
Idler
Pulley
•
Figure 18
13
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
•
Back out the stop bolt until the support bracket
rests on the auger pulley. See Figure 20.
Slip belt between friction wheel and friction wheel
disc. See Figure 20. Remove and replace belt.
Reassemble following the instructions in reverse
order.
Screws
Friction Wheel Rubber
Hub
Screws
NOTE: The support bracket must rest on the stop bolt
after the new belt has been assembled. See Figure 20.
Servicing Friction Wheel Rubber
The rubber on the friction wheel is subject to wear and
should be checked after 25 hours of operation, and
periodically thereafter. Replace the friction wheel
rubber if any signs of wear or cracking are found.
Friction Wheel Plates
Figure 22
•
•
Reassemble new friction wheel rubber to the
friction wheel plates and hub, tightening the six
screws in rotation and with equal force.
Position the friction wheel assembly up onto the pin
of the shift rod assembly, and slide the shaft
through the assembly. Reassemble in reverse
order.
•
•
Drain the gasoline from the snow thrower.
Tip the snow thrower up and forward, so that it rests
on the housing.
•
•
•
Remove six self-tapping screws from the frame
cover underneath the snow thrower.
Remove the click pins which secure the wheels,
and remove the wheels from the axle.
Using a 7/8" wrench to hold the shaft, loosen, but
do not completely remove, the hex nut and bell
washer on the left end of gear shaft. See Figure 21.
Augers
The augers are secured to the spiral shaft with two
shear bolts and hex lock nuts. Refer to Figure 14. If you
hit a foreign object or ice jam, the snow thrower is
designed so that the bolts mayshear. If the augers will
not turn, check to see if the bolts have sheared.
Hex Nut /
Bell Washer
IMPORTANT: NEVER replace the auger shear bolts with
standard hex bolts. Any damage to the auger gearbox
or other components as a result of doing so will NOT be
coved by your snow throwers warranty.
Off-season Storage
WARNING: Never store engine with fuel in
tank indoors or in poorly ventilated areas,
where fuel fumes may reach an open
flame, spark or pilot light as on a furnace,
water heater, clothes dryer or other gas
appliance.
•
If unit is to be stored over 30 days, prepare engine
for storage as instructed in the separate engine
manual packed with your unit.
NOTE: Snow thrower shown resting on its
auger housing. Wheels not shown for clarity.
•
•
•
Remove all debris from the exterior of the engine
and equipment.
Follow the lubrication recommendations found in
Section 7 of this manual.
Figure 21
•
Lightly tap the hex nut to dislodge the ball bearing
from the right side of frame before removing the hex
nut and bell washer from left end of shaft.
Move the gear shaft to the right and slide the friction
wheel assembly from the shaft.
Remove the six screws from the friction wheel
assembly (three from each side). Remove the
friction wheel rubber from between the friction
wheel plates. See Figure 22.
Always store the snow thrower in a clean, dry area.
•
•
NOTE: When storing any type of power equipment in
an unventilated or metal storage shed, care should be
taken to rust proof the equipment. Using a light oil or
silicone, coat the equipment, especially any chains,
springs, bearings and cables.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9: TROUBLESHOOTING
Problem
Cause
Remedy
Engine fails to start 1. Fuel tank empty, or stale fuel.
1. Fill tank with clean, fresh gasoline.
Fuel becomes stale after thirty days
unless a fuel stabilizer is used.
2. Clean the fuel line.
2. Blocked fuel line.
3. Choke not in ON position
4. Faulty spark plug.
3. Move switch to ON position
4. Clean, adjust gap or replace.
5. Safety key not in ignition switch on engine. 5. Insert the key fully into the switch.
6. Spark plug wire disconnected.
7. Primer button not being used properly.
6. Connect spark plug wire.
7. Refer to the engine manual for proper
priming instructions.
8. Fuel shut-off valve closed.
8. Open fuel shut-off valve.
Engine runs erratic 1. Unit running on CHOKE.
1. Move choke lever to OFF position.
2. Clean fuel line. Refill with fresh fuel.
3. Drain fuel tank and carburetor. Refill
with fresh fuel.
2. Blocked fuel line or stale fuel.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
4. Refer to the engine manual packed
with your unit or have carburetor
adjusted by an authorized engine
service dealer.
Loss of power
1. Spark plug wire loose.
2. Gas cap vent hole plugged.
1. Connect and tighten spark plug wire.
2. Remove ice and snow from gas cap.
Be certain vent hole is clear.
3. Exhaust port plugged.
3. Rerer to the Maintenance section of
the engine manual.
Engine overheats
1. Carburetor not adjusted properly.
1. Refer to the engine manual or have
the carburetor adjusted by an
authorized engine service dealer.
Excessive vibration 1. Loose parts or damaged auger.
1. Stop engine immediately and
disconnect spark plug wire. Tighten all
bolts and nuts. If vibration continues,
have unit serviced by an authorized
service dealer.
Unit fails
to propel itself
1. Traction control cable in need of
adjustment.
1. Adjust traction control cable. Refer to
Section 6 of this manual.
2. Drive belt loose or damaged.
2. Replace drive belt. Refer to Section 8
of this manual.
Unit fails
to discharge snow
1. Discharge chute clogged.
1. Stop engine immediately and
disconnect spark plug wire. Clean
chute area and auger housing.
2. Stop engine immediately and
disconnect spark plug wire. Remove
object from auger.
2. Foreign object lodged in auger.
3. Auger control cable in need of adjustment. 3. Adjust auger control cable. Refer to
Section 6 of this manual.
4. Auger belt loose or damaged.
4. Refer to Section 8 of this manual.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 10: PARTS LIST
Models 550 & 750
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
4
17
11
9
16
13
8
15
10
1
14
5
18
6
3
7
12
3
2
Ref.
No.
Part No.
Part Description
618-0123
RH Housing
1.
2.
3.
4.
618-0418
710-0642
LH Housing w/Fitting
Self Tapping Screw, 1/4-20 x .75
711-1020
711-0908
Spiral Axle, 22” (550)
Spiral Axle, 24” (750)
714-0161
715-0143
717-0528
717-0526
718-0186
721-0325
721-0327
736-0351
736-0369
736-0445
741-0662
741-0663
Hi-Pro Key, 3/16 x 5/8
Spring Spirol Pin, .25 x 1.25
Worm Gear, 20-tooth
Worm Shaft
5.
6.
7.
8.
Thrust Collar
9.
Grease Plug
10.
11.
12.
13.
14.
15.
16.
17.
Grease Seal
Flat Washer, .76 x 1.5 x .030
Flat Washer, .508 x 1.0 x .020
Flat Washer, .76 x 1.5 x .060
Flange Bearing, .75 x 1.0 x .59
Flange Bearing, .503 ID x .75 OD
618-0413
618-0414
Gear Assy Complete, 22” (550)
Gear Assy Complete, 24” (750)
737-3000
737-0168
Grease Fitting, 3/16” Drive
Grease (Two Ounces)
18.
—
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
20
27
37
37
Drive Clutch
Cable
39
20
Auger Clutch
Cable
5
4
13
1
7
11
38
6
3
10
4
40
1
2
14
36
15
26
5
16
25
7
9
10
11
25
31
28
12
23
21
17
8
18
4
32
33
24
22
1
1
20
29
5
8
34
19
Auger Clutch
Cable
26
35
Blower
Housing
30
1
1
44
42
42
41
43
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
Ref.
No.
Ref.
Part No.
717-1444
Part Description
7-Tooth Shaft
Part No.
No.
Part Description
Hex Screw
710-1652
1.
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
38.
39.
40.
41.
715-0249
714-0143
684-0042B
656-0012A
684-0013B
746-0897
748-0190
684-0021
732-0264
712-0711
746-0898
738-0869
717-1445
714-0126
717-1444
618-0063
Roll Pin
784-5688
2.
Drive Cable Guide Bracket
Auger Clutch Cable Bracket
Roller Cable
Clik Pin
784-5687
3.
Friction Wheel Assembly
Friction Disc Wheel
Wheel Shift Rod Assembly
Drive Cable
756-0625
4.
738-0924
5.
Hex Screw 1/4-28
Frame Assembly
684-0030
6.
741-0563
7.
Ball Bearing
Spacer
736-0105
8.
Bell Washer
Friction Wheel Bracket Ass’y
Extension Spring
Jam Nut, 3/8-24
Drive Cable
712-0116
9.
Lock Jam Nut
741-0598
10.
Hex Flange Bearing
Flat Washer
736-0188
11.
784-5689A
12.
Front Support Guide Bracket
Lock Hex Screw
Axle
710-0538
13.
Gear
736-0242
14.
Bell Washer .340 ID x .872 OD
Cotter Pin
Key
714-0474
15.
7-Tooth Shaft
Friction Wheel Bearing
736-0160
16.
Flat Washer .536 ID x .930 OD
Hex Washer Screw 1/4-20
Frame Shift Bracket
Frame Cover
710-0788
17.
734-1732
734-1859
Tire Only, 13 x 4 (550)
Tire Only, 15 x 5 (750)
784-5590
18.
784-5638
710-0599
736-0351
717-1445
714-0126
19.
20.
21.
22.
23.
741-0401
734-0255
Sleeve Bearing
Air Valve
42.
43.
44.
Hex Washer Screw 1/4-20
Flat Washer .760 ID x .50 OD
Gear
634-0114
634-0140
Wheel Assembly (550)
Wheel Assembly (750)
(Incl. Ref. 41, 42, & 43)
Key
NOTE: For painted parts, please refer to
the list of color codes below. Please add the
applicable color code, wherever needed, to
the part number to order a replacement part.
For instance, if a part, numbered 700-xxxx,
is painted Oyster Gray, the part number to
order would be 700-xxxx-0662.
Oyster Gray: 0662
Powder Black: 0637
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
2
1
3
4
5
11
10
9
15
18
6
14
12
7
8
13
32
31
9
18
19
20
22
16
43
23
21
31
27
10
13
23
30
34
28
25
18
13
38
26
43
35
31
22
30
18
32
31
33
16
41
36
37
17
40
39
24
40
42
39
29
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
Ref.
No.
Ref.
Part No.
784-5618
Part Description
Bearing Housing
Part No.
No.
Part Description
712-0116
1.
Lock Jam Nut 3/8-24
Flat Idler
24.
25.
26.
27.
28.
29.
30.
31.
32.
33.
710-0703
710-0604
736-0169
712-0798
741-0245
784-5038B
736-0242
712-3010
Carriage Screw 1/4-20 x .75
Hex Washer Screw 5/16-18
Lock Washer 3/8
Hex Nut 3/8-16
756-0178
2.
784-5632A
3.
Auger Idler Arm
Hex Cap Screw 3/8-24 x 1.50
Shoulder Screw
Wave Washer
710-0459A
4.
738-0281
5.
Hex Flange Bearing
Skid Shoe
736-0174
6.
732-0611
7.
Extension Spring
Hex Nut 5/16-18
Hex Nut 5/16-18
Lock Washer 5/16
Housing
Bell Washer
712-3068
8.
Hex Nut 5/16-18
712-3010
9.
784-5576
784-5581A
21.66” Shave Plate (550)
23.66” Shave Plate (750)
736-0119
10.
05931
11.
12.
13.
14.
15.
710-0260
684-0065
715-0114
Carriage Bolt 5/16-18 x .62
Impeller Assembly
Pin
34.
35.
36.
37.
741-0309
710-0451
705-5226
Ball Bearing
Carriage Bolt 5/16-18 x .75
Chute Reinforcement
618-0413
618-0414
22” Gear Assembly (550)
24” Gear Assembly (750)
684-0052B
684-0039C
22” Housing Ass’y (550)
24” Housing Ass’y (750)
605-5252A
605-5188A
22” Spiral RH (550)
24” Spiral RH (750)
38.
712-3010
712-0429
736-0242
741-0475
784-5647
731-1379A
712-0324
736-0463
Hex Nut 5/16-18
Lock Nut 5/16-18
Bell Washer
16.
17.
18.
19.
20.
21.
22.
23.
736-0188
Flat Washer
39.
40.
41.
741-0493A
Flange Bushing
Bushing
605-5253A
605-5189A
22” Spiral LH (550)
24” Spiral LH (750)
Chute Crank Bracket
Chute Adapter
Hex Lock Nut 1/4-20
Flat Washer
710-0890A
736-0231
Shear Bolt 5/16-18 x 1.5
42.
43.
Flat Washer, .344 x 1.12 x .87
NOTE: For painted parts, please refer to
the list of color codes below. Please add the
applicable color code, wherever needed, to
the part number to order a replacement part.
For instance, if a part, numbered 700-xxxx,
is painted Oyster Gray, the part number to
order would be 700-xxxx-0662.
Oyster Gray: 0662
Powder Black: 0637
21
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
1
2
28
3
5
4
27
8
9
11
13
12
10
15
16
4
22
7
6
20
23
24
14
17
18
26
19
21
25
22
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
Ref.
No.
Part No.
710-1652
Part Description
Hex Washer Screw 1/4-20 x.625
Belt Cover
1.
2.
731-1324
732-0339
710-0627
710-3005
05896A
Extension Spring
Hex Screw 5/16-24 x .75
Hex Cap Screw 3/8-16 x 1.25
Drive Clutch Bracket
Shoulder Spacer
Pulley Half
3.
4.
5.
6.
748-0234
756-0985
754-0343
756-0984
736-0270
710-0230
756-0313
710-1245
712-0181
756-0569
736-0242
736-0505
736-0507
754-0430A
756-0967
736-0247
736-0331
710-0696
748-0360
710-0654A
629-0071
OEM-390-987
7.
8.
V-Belt
9.
Pulley Half
10.
11.
12.
13.
14.
15.
16.
17.
18.
19.
20.
21.
22.
23.
24.
25.
26.
27.
28.
Bell Washer
Hex Cap Screw 1/4-28 x .50
Flat Idler
Lock Cap Screw 5/16-24
Lock Jam Nut 3/8-16
Pulley Half
Bell Washer
Flat Washer
Washer
Belt
Auger Pulley
Flat Washer
Bell Washer
Hex Cap Screw 3/8-24
Pulley
Hex Washer Screw 3/8-16 x 1.0
Extension Cord
Electric Start Kit (Includes Ref. 27)
IMPORTANT: For a proper working machine, use Factory
Approved Parts.
V-BELTS are specially designed to engage and disengage
safely. A substitute (non OEM) V-Belt can be dangerous by
not disengaging completely
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Models 550 & 750
67
70
73
10
35
32
13
44
19
32
45
46
45
38
33
49
51
68
42
32
35
11
41
72
74
32
39
36
48
41
44
43
4
69
30
18
71 (for ground wire
34
54
of light ass’y)
62
47
40
74
39
27
42
59
55
11
53
43
37
12
20
31
5
11
66
9
23
29
B
A
55
64
15
B
A
63
65
60
28
21
24
16
59
6
25
1
14
3
26
20
52
4
15
20
12
18
54
7
11
58
61
56
55
2
17
57
12
8
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 550 & 750
Ref.
No.
Ref.
Part No.
732-0746
Part Description
Part No.
No.
Part Description
Shift Arm Assembly
Torsion Spring, .44 x .8
Rubber Bumper
684-0008A
1.
38.
39.
40.
41.
42.
43.
44.
45.
46.
47.
48.
49.
50.
51.
52.
53.
54.
55.
56.
57.
58.
59.
60.
61.
62.
63.
64.
65.
66.
67.
68.
69.
70.
71.
72.
73.
74.
735-0199A
736-0105
736-0119
736-0509
746-0778
747-0877
748-0362
748-0363
784-5619A
784-5679
784-5680
784-5681
784-5682
710-0451
710-0805
710-0896
712-0429
712-3027
731-0851A
731-1300A
731-1313C
731-1320
736-0159
736-0506
746-0896
746-0901
784-5594
784-5604
629-0059
684-0036
684-0059
710-1003
712-0271
720-0232
725-1658
720-0274
684-0022
2.
Chute Crank Ass’y
Bell Washer, .401 x .87 x .063
Lock Washer, 5/16
715-0138
3.
Rolled Pin
710-0262
4.
Carriage Bolt, 5/16-18 x 1.5
Carriage Bolt, 5/16-18 x 2.25
Self Tapping Screw, 1/4-20 x 1
Hex Cap Screw, 5/16-18 x .75
Hex Cap Screw, 1/4-20 x .75
Ferrule, 5/16-18 x .312
Headlamp Retainer
Special Washer, .35 x .72 x .13
Cable “Z” Fitting
710-0449
5.
710-0788
6.
Cam Rod
710-3008
7.
Cam Handle Lock
710-3015
8.
Handle Lock Pawl
711-0677
9.
Shift Handle
747-1136
10.
LH Handle Support Bracket
RH Handle Support Bracket
LH Handle Support Bracket
RH Handle Support Bracket
Carriage Bolt, 5/16-18 x .75
Hex Cap Screw, 516-18 x 1.5
Screw, 1/4-14 x .625
Hex Lock Nut, 5/16-18
Hex Flange Lock Nut, 1/4-20
Lower Chute Flange Keeper
Lower Chute
712-3010
11.
Hex Nut, 5/16-18
714-0104
12.
Internal Cotter Pin
725-1672
13.
Lens Assembly / Lamp Housing
Chute Crank Knob
720-0201A
14.
720-0284
15.
Wing Knob, 5/16-18
726-0100
16.
Push Cap, 3/8
736-0185
17.
Flat Washer, .375 x .738 x .063
Bell Washer, .34 x .872
Handle Panel
736-0242
18.
731-2275
19.
736-0275
20.
Flat Washer, .344 x .688 x .065
Saddle Washer, .32 x .93
Plastic Bushing
736-0451
21.
Chute Tilt Cable Guide
Upper Chute
741-0475
22.
747-0620A
23.
Upper Shift Rod
Washer, 5/16
747-0621
24.
Lower Shift Rod
Special Washer, .28 x 1.2 x .06
Chute Deflector Control Cable
Chute Deflector Cable w/ Clip
Cable Bracket
747-0697
25.
Eyebolt
—
735-0234
749-0951
749-0952
749-0953
750-0963
684-0102
710-0459A
710-0599
711-0653
712-0116
714-0507
732-0145
732-0193
Eyebolt Grommet (Not Shown)
Lower Handle
26.
27.
28.
29.
30.
31.
32.
33.
34.
35.
36.
37.
RH Handle (Upper)
LH Handle (Upper)
Chute Tilt Handle
Shift Rod Connector
Handle Panel Ass’y With Tilt
Hex Cap Screw, 3/8-24 x 1.5
Self Tapping Screw, 1/4-20 x .5
Clevis Pin
Halogen Light Harness
RH Engagement Handle Ass’y
LH Engagement Handle Ass’y
Special Screw, #10-16 x .625
Hex Sems Nut, 1/4-20
Plastic Knob
Jam Nut, 3/8-24
Cotter Pin, 3/32 x .75
Compression Spring, .36 x 1.0
Comp. Spring, .39 x .6 x .88
Halogen Lamp, 12-volt, 27 Watt
Handle Grip
25
Download from Www.Somanuals.com. All Manuals Search And Download.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
c. Routine maintenance items such as lubricants, filters,
blade sharpening and tune-ups, or adjustments such
as brake adjustments, clutch adjustments or deck
adjustments; and normal deterioration of the exterior
finish due to use or exposure.
The limited warranty set forth below is given by White Out-
door Products Co. with respect to new merchandise pur-
chased and used in the United States, its possessions and
territories.
d. White Outdoor Co. does not extend any warranty for
products sold or exported outside of the United States
of America, its possessions and territories, except
those sold through White Outdoor Co. authorized
channels of export distribution.
White Outdoor Products Co. warrants this product against
defects in material and workmanship for a period of two (2)
years commencing on the date of original purchase and
will, at its option, repair or replace, free of charge, any part
found to be defective in material or workmanship. This lim-
ited warranty shall only apply if this product has been oper-
ated and maintained in accordance with the Operator’s
Manual furnished with the product, and has not been sub-
ject to misuse, abuse, commercial use, neglect, accident,
improper maintenance, alteration, vandalism, theft, fire,
water or damage because of other peril or natural disaster.
Damage resulting from the installation or use of any acces-
sory or attachment not approved by White Outdoor Prod-
ucts Co. for use with the product(s) covered by this manual
will void your warranty as to any resulting damages.
No implied warranty, including any implied warranty of
merchantability or fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty or guaranty, whether written or oral,
except as mentioned above, given by any person or
entity, including a dealer or retailer, with respect to any
product shall bind White Outdoor Co. During the
period of the Warranty, the exclusive remedy is repair
or replacement of the product as set forth above.
(Some states do not allow limitations on how long an
implied warranty lasts, so the above limitation may not
apply to you.)
Normal wear parts or components thereof are subject to
separate terms as follows: All normal wear part or compo-
nent failures will be covered on the product for a period of
90 days regardless of cause. After 90 days, but within the
two year period, normal wear part failures will be covered
ONLY IF caused by defects in material or workmanship of
OTHER component parts. Normal wear parts and compo-
nents include, but are not limited to, belts, blades, blade
adapters, grass bags, rider deck wheels, seats, snow
thrower skid shoes, shave plates and tires. Batteries are
covered by a 90-day limited replacement warranty.
The provisions as set forth in this Warranty provide the
sole and exclusive remedy arising from the sales.
White Outdoor Co. shall not be liable for incidental or
consequential loss or damages including, without limi-
tation, expenses incurred for substitute or replace-
ment lawn care services, for transportation or for
related expenses, or for rental expenses to temporarily
replace a warranted product. (Some states do not allow
the exclusion or limitation of incidental or consequential
damages, so the above exclusion or limitation may not
apply to you.)
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE THROUGH YOUR LOCAL
WHITE OUTDOOR DEALER. To locate the dealer in your
area, please check for a listing in the Yellow Pages or con-
tact the Customer Dealer Referral Line of White Outdoor
Co. by calling 1-330-225-8883 or writing to P.O. Box
361131, Cleveland, Ohio 44136-0019. No product returned
directly to the factory will be accepted unless prior written
permission has been extended by White Outdoor Co.
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of the safety features of the product shall void this War-
ranty. You assume the risk and liability for loss, damage, or
injury to you and your property and/or to others and their
property arising out of the use or misuse or inability to use
the product.
This limited warranty does not provide coverage in the
following cases:
This limited warranty shall not extend to anyone other than
the original purchaser, original lessee or the person for
whom it was purchased as a gift.
a. The engine or component parts thereof. These items
carry a separate manufacturer’s warranty. Please refer
to the applicable manufacturer’s warranty on these
items.
b. Log splitter pumps, valves and cylinders have a sepa-
rate one year warranty.
How State Law Relates to this Warranty: This limited
warranty gives you specific legal rights, and you may also
have other rights which vary from state to state.
Download from Www.Somanuals.com. All Manuals Search And Download.
|