Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
Two-Stage Snow Thrower — E, F Style
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any uniiproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A
FORM NO. 769-01275D
06/22/2006
Download from Www.Somanuals.com. All Manuals Search And Download.
$!.'%2
$!.'%2
ꢃꢀ
+%%0 !7!9 &2/- 2/4!4).' )-0%,,%2
!.$ !5'%2ꢀ #/.4!#4 7)4( )-0%,,%2 /2
1
!5'%2 #!. !-054!4% (!.$3 !.$ &%%4
ꢀ
53% #,%!.ꢁ/54 4//, 4/ 5.#,/'
ꢄꢀ
ꢅꢀ
$)3#(!2'% #(54%ꢀ
Safety
Labels
$)3%.'!'% #,54#( ,%6%23ꢂ 34/0 %.').%ꢂ
!.$ 2%-!). "%().$ (!.$,%3 5.4), !,,
-/6).' 0!243 (!6% 34/00%$ "%&/2%
5.#,/'').' /2 3%26)#).' -!#().%ꢀ
4/ !6/)$ 4(2/7. /"*%#43 ).*52)%3ꢂ
.%6%2 $)2%#4 $)3#(!2'% !4 "934!.$%23ꢀ
53% %842! #!54)/. 7(%. /0%2!4).' /.
'2!6%, 352&!#%3ꢀ
ꢆꢀ
ꢇꢀ
!6/)$ ).*529 &2/-
2/4!4).' !5'%2 ꢀ
+%%0 (!.$3ꢁ &%%4
!.$ #,/4().' !7!9ꢂ
2%!$ /0%2!4/2g3 -!.5!,ꢀ
#,%!.ꢀ/54 4//,
WARNING
$!.'%2
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
manual before at-
.%6%2 054 (!.$ ). #(54%ꢀ #/.4!#4 7)4(
2/4!4).' 0!243 #!. !-054!4% &).'%23
!.$ (!.$3ꢀ
3(54 /&& %.').% !.$ 7!)4 5.4), !,,
-/6).' 0!243 (!6% 34/00%$ "%&/2%
5.#,/'').'ꢀ
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
53% #,%!.ꢁ/54 4//, /2 7//$%. 34)#+ 4/
5.#,/' $)3#(!2'% #(54%ꢀ
HEED ITS WARNING!
A chute clean-out tool is fastened to the top of the
auger housing with a mounting clip. The tool is designed
to clear a chute assembly of ice and snow.
Your Responsibility
Restrict the use
#HUTE #LEANꢀOUT 4OOL
of this power machine
to persons who read,
understand
This item is fastened with a cable tie at the factory. Cut
the cable tie before operating the snow thrower.
WARNING: Never use your
hands to clear a clogged chute
assembly. Shut off engine and
remain behind handles until
all moving parts have stopped
before using the clean-out tool
to clear the chute assembly.
and follow the warnings
and instructions
in this manual
and on the machine.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-
nents contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
ꢀ
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator can
result in serious injury. This machine is capable of amputating hands and feet and throwing objects.
Safe
Operation Failure to observe the following safety instructions could result in serious injury or death.
Training
Preparation
1. Read, understand, and follow all instructions on the
machine and in the manual(s) before attempting to
assemble and operate. Keep this manual in a safe place for
future and regular reference and for ordering replacement
parts.
1. Thoroughly inspect the area where the equipment is to be
used. Remove all doormats, newspapers, sleds, boards,
wires, and other foreign objects, which could be tripped over
or thrown by the auger/impeller.
Practices
2. Always wear safety glasses or eye shields during operation
and while performing an adjustment or repair to protect your
eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
2. Be familiar with all controls and their proper operation.
Know how to stop the machine and disengage them quickly.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the operation instructions and safety rules in
this manual and should be trained and supervised by a
parent.
3. Do not operate without wearing adequate winter outer
garments. Do not wear jewelry, long scarves, or other
loose clothing which could become entangled in moving
parts. Wear footwear which will improve footing on slippery
surfaces.
WARNING
4. Never allow adults to operate this machine without proper
instruction.
5. Thrown objects can cause serious personal injury. Plan
your snow-throwing pattern to avoid discharge of material
toward roads, bystanders, and the like.
6. Keep bystanders, helpers, pets, and children at least 75
feet from the machine while it is in operation. Stop machine
if anyone enters the area.
4. Use a grounded three-wire extension cord and receptacle
for all units with electric start engines.
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
5. Adjust collector housing height to clear gravel or crushed
rock surfaces.
6. Disengage all control levers before starting the engine.
7. Never attempt to make any adjustments while engine is
running, except where specifically recommended in the
operator’s manual.
7. Exercise caution to avoid slipping or falling, especially
when operating in reverse.
8. Let engine and machine adjust to outdoor temperature
before starting to clear snow.
9. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes,
which can ignite. Wash your skin and change clothes
immediately.
manual before at-
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
c. Never fuel machine indoors.
d. Never remove gas cap or add fuel while the engine is hot
or running.
HEED ITS WARNING!
e. Allow engine to cool at least two minutes before refuel-
ing.
Your Responsibility
Restrict the use
f. Never over fill fuel tank. Fill tank to no more than ½-inch
below bottom of filler neck to provide space for fuel
expansion.
of this power machine
to persons who read,
understand
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine and equip-
ment. Move machine to another area. Wait five minutes
before starting the engine.
and follow the warnings
and instructions
in this manual
i. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light (e.g. furnace,
water heater, space heater, clothes dryer etc.).
j. Allow machine to cool at least five minutes before
storing.
and on the machine.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Maintenance & Storage
1. Do not put hands or feet near rotating parts, in the
auger/impeller housing or chute assembly. Contact with the
rotating parts can amputate hands and feet.
1. Never tamper with safety devices. Check their proper
operation regularly. Refer to the maintenance and adjust-
ment sections of this manual.
ꢀ
2. The auger/impeller control lever is a safety device. Never
bypass its operation. Doing so makes the machine unsafe
and may cause personal injury.
2. Before cleaning, repairing, or inspecting machine disen-
gage all control levers and stop the engine. Wait until the
auger/impeller come to a complete stop. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
3. The control levers must operate easily in both directions
and automatically return to the disengaged position when
released.
Safe
Operation
Practices
3. Check bolts and screws for proper tightness at frequent
intervals to keep the machine in safe working condition.
Also, visually inspect machine for any damage.
4. Do not change the engine governor setting or over-speed
the engine. The governor controls the maximum safe
operating speed of the engine.
4. Never operate with a missing or damaged chute assembly.
Keep all safety devices in place and working.
5. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless and
deadly gas.
5. Snow thrower shave plates and skid shoes are subject to
wear and damage. For your safety protection, frequently
check all components and replace with original equipment
manufacturer’s (OEM) parts only. “Use of parts which do
not meet the original equipment specifications may lead to
improper performance and compromise safety!”
6. Check controls periodically to verify they engage and
disengage properly and adjust, if necessary. Refer to the
adjustment section in this operator’s manual for instructions.
7. Maintain or replace safety and instruction labels, as neces-
sary.
6. Do not operate machine while under the influence of alcohol
or drugs.
7. Muffler and engine become hot and can cause a burn. Do
not touch.
8. Exercise extreme caution when operating on or crossing
gravel surfaces. Stay alert for hidden hazards or traffic.
9. Exercise caution when changing direction and while operat-
ing on slopes.
WARNING
10. Plan your snow-throwing pattern to avoid discharge towards
windows, walls, cars etc. Thus, avoiding possible property
damage or personal injury caused by a ricochet.
11. Never direct discharge at children, bystanders, and pets or
allow anyone in front of the machine.
This symbol points
8. Observe proper disposal laws and regulations for gas, oil,
etc. to protect the environment.
out important safety
instructions, which if
not followed, could
9. Prior to storing, run machine a few minutes to clear snow
from machine and prevent freeze up of auger/impeller.
10. Never store the machine or fuel container inside where
there is an open flame, spark or pilot light such as a water
heater, furnace, clothes dryer etc.
12. Do not overload machine capacity by attempting to clear
snow at too fast of a rate.
13. Never operate this machine without good visibility or light.
Always be sure of your footing and keep a firm hold on the
handles. Walk, never run.
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
11. Always refer to the operator’s manual for proper instructions
on off-season storage.
14. Disengage power to the auger/impeller when transporting or
not in use.
Do not modify engine
15. Never operate machine at high transport speeds on slippery
surfaces. Look down and behind and use care when
backing up.
instructions in this man-
ual before attempting to
operate this machine.
Failure to comply with
these instructions may
result in personal injury.
When you see this
To avoid serious injury or death, do not modify engine in any
way.Tampering with the governor setting can lead to a runaway
engine and cause it to operate at unsafe speeds. Never tamper
with factory setting of engine governor.
16. If the machine should start to vibrate abnormally, stop the
engine, disconnect the spark plug wire and ground it against
the engine. Inspect thoroughly for damage. Repair any
damage before starting and operating.
Notice regarding Emissions
Engines which are certified to comply with California and federal
EPA emission regulations for SORE (Small Off Road Equipment)
are certified to operate on regular unleaded gasoline, and may
include the following emission control systems: Engine Modifica-
tion (EM) and Three Way Catalyst (TWC) if so equipped.
17. Disengage all control levers and stop engine before you
leave the operating position (behind the handles). Wait
until the auger/impeller comes to a complete stop before
unclogging the chute assembly, making any adjustments, or
inspections.
symbol.
HEED IT’S WARNING!
Your Responsibility
18. Never put your hand in the discharge or collector openings.
Always use the clean-out tool provided to unclog the dis-
charge opening. Do not unclog chute assembly while engine
is running. Shut off engine and remain behind handles until
all moving parts have stopped before unclogging.
19. Use only attachments and accessories approved by the
manufacturer (e.g. wheel weights, tire chains, cabs etc.).
20. If situations occur which are not covered in this manual, use
care and good judgment. Contact your dealer or call the
customer service number found on page two.
Your Responsibility
Restrict the use
Restrict the use of this power machine to persons who read, un-
derstand and follow the warnings and instructions in this manual
and on the machine.
of this power machine
to persons who read,
understand
and follow the warnings
and instructions
in this manual
and on the machine.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
ꢁ
Setting Up
Your Snow
Thrower
1. Observe the lower rear area of the snow thrower to
be sure both cables are aligned with roller guides
before pivoting the handle upward.
3
NOTE: Reference to right
and left side of the machine
are observed from the
operating position.
2. Secure the handle by tightening the plastic knob
located on both the left and right sides of the handle.
Remove and discard any rubber bands, if present.
They are for packaging purposes only.
3. Position the chute assembly over the base.
NOTE: This Operator’s
Manual covers several
models. Snow thrower
4. Close the flange keepers to secure the chute
assembly to the chute base. The flange keepers will
click into place when properly secure.
features vary by model. Not
all features discussed in
this manual are applicable
to all snow thrower models.
NOTE: If the flange keepers will not easily click into
place, use the palm of your hand to apply swift, firm
pressure to the back of each.
NOTE: Two replacement
auger shear pins and bow
tie cotter pins are provided
for your convenience. Store
in a safe place until
4
needed. Refer to “Augers”
in the Maintenance Section
of this manual for more
information.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Remove the flat washer and hairpin clip from the end
of the chute directional control.
5
Insert the end of the chute directional control into the
lower bracket and secure with the flat washer and hair-
pin clip just removed. If necessary, the lower bracket
can be adjusted. Refer to Chute Bracket Adjustment.
on Page 13.
ꢁ
Setting Up
Your Snow
Thrower
Adjustments
Auger Control
IMPORTANT: Prior to operating your snow thrower, refer
to Auger Control Test on page 11. Read and follow all
instructions carefully and perform all adjustments to verify
your snow thrower is operating safely and properly.
Skid Shoes
IMPORTANT: It is not recommended that you operate
this snow thrower on gravel as loose gravel can be easily
picked up and thrown by the auger causing personal
injury or damage to the snow thrower.
IMPORTANT
Prior to operating your
snow thrower, refer
to Auger Control Test
on page 11. Read and
follow all instructions
carefully and perform
all adjustments to verify
your snow thrower is
operating safely and
properly.
The snow thrower skid shoes are adjusted upward at the
factory for shipping purposes. Adjust them downward, if
desired, prior to operating the snow thrower. Refer to Skid
Shoes on page 13.
NOTE: If you choose to operate the snow thrower on
a gravel surface, keep the skid shoes in position for
maximum clearance between the ground and the shave
plate.
Tire Pressure
Before operating, check tire pressure and reduce pres-
sure in both tires to between 15 psi and 20 psi.
NOTE: If the tire pressure is not equal in both tires, the
unit may not travel in a straight path and the shave plate
may wear unevenly.
ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
KnowYour Snow Thrower
3HIFT ,EVER
$RIVE #ONTROL
!UGER #ONTROL
4
%LECTRIC 3TART "UTTON
'AS #AP
Operating
Your Snow
Thrower
#HUTE $IRECTIONAL #ONTROL
#HUTE !SSEMBLY
/IL &ILL
#LEAN /UT
4OOL
%NGINE #ONTROLS
2ECOIL 3TARTER
(ANDLE
%LECTRIC 3TARTER /UTLET
0RIMER
)GNITION
+EY
WARNING
#HOKE
#ONTROL
3KID 3HOE
!UGERS
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
4HROTTLE
#ONTROL
Figure 1
Now that you have set up your snow thrower for
operation, get acquainted with its controls and fea-
tures. These are described below and illustrated in
Figure 1. This knowledge will allow you to use your
Choke Control
Use extreme care
when handling
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
new equipment to its fullest potential.
NOTE: For detailed starting instructions and more
information on all engine controls, refer to the separate
engine manual packed with your unit
The choke control is found on the rear of the engine and
is activated by rotating the knob clockwise. Activating the
choke control closes the choke plate on the carburetor
and aids in starting the engine.
Shift Lever
The shift lever is located in the right side of the handle
panel and is used to determine gorund speed and
direction of travel.
Throttle Control
The throttle control is located on the
engine. It regulates the speed of the
engine and will shut off the engine when
pushed down completely.
Primer
NOTE: Snow throwers vary
by model with regard to
features and components.
Your snow thrower may
NOT resemble, in detail,
snow throwers illustrated
in figures throughout this
manual.
Depressing the primer forces fuel directly
into the engine’s carburetor to aid in
cold-weather starting.
Forward
There are six forward (F) speeds. Position one (1) is the
slowest and position six (6) is the fastest.
Oil Fill
Engine oil level can be checked and oil
added through the oil fill.
Reverse
There are two reverse (R) speeds. One (1) is the slower
and two (2) is the faster.
34/0
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Control
Chute Directional Control
!5'%2
#/.42/,
#(54% $)2%#4)/.!, #/.42/,
!$*534!",%
#(54% 4),4
4
$)3#(!2'%
,%&4
$)3#(!2'%
2)'(4
Operating
Your Snow
Thrower
'/
The chute directional control is located on left side of the
snow thrower.
The auger control is located on the left handle. Squeeze
the control grip against the handle to engage the augers
and start snow throwing action. Release to stop.
To change the direction in which snow is thrown, turn
chute directional control as follows:
•
Crank clockwise to discharge to the left.
Drive Control / Auger Clutch Lock*
•
Crank counterclockwise to discharge to the right.
$2)6%
#/.42/,
Clean-Out Tool
WARNING: Never use your hands
to clear a clogged chute assembly.
Shut off engine and remain behind
handles until all moving parts have
stopped before unclogging.
WARNING
The operation of
any snow thrower
can result in foreign
objects being thrown
into the eyes, which
can damage your
eyes severely. Always
wear safety glasses
while operating the
snow thrower, or while
performing any adjust-
ments or repairs on it.
'/
The chute clean-out tool is fastened to the
top of the auger housing with a mounting clip. The tool is
designed to clear a clogged chute assembly.
The drive control is located on the right handle. Squeeze
the control grip against the handle to engage the wheel
drive. Release to stop.
NOTE: This item is fastened with a cable tie to the rear
of the auger housing at the factory. Cut the cable tie
before operating the snow thrower.
*On select models, the drive control also locks the auger
control so that you can operate the chute directional
control without interrupting the snow throwing process.
If the auger control is engaged simultaneously with the
drive control, the operator can release the auger control
(on the left handle) and the augers will remain engaged.
Release both controls to stop the augers and wheel
drive.
Skid Shoes
Position the skid shoes based on surface conditions.
Adjust upward for hard-packed snow. Adjust downward
when operating on gravel or crushed rock surfaces.
Electric Starter Outlet
Requires the use of a three-prong outdoor extension cord
and a 120V power source/wall outlet.
Be sure no one other
than the operator is
standing near the snow
thrower while starting
engine or operating
snow thrower. Never
run engine indoors or
in enclosed, poorly
ventilated areas. En-
gine exhaust contains
carbon monoxide, an
odorless and deadly
gas. Keep hands, feet,
hair and loose clothing
away from any moving
parts on engine and
snow thrower.
IMPORTANT: Always release the drive control before
changing speeds.
Ignition Key
Augers
The ignition key is a safety devise. It must be fully
inserted in order for the engine to start. Remove the
ignition key when the snow thrower is not in use.
Do not turn the ignition key in an attempt to start the
engine. Doing so may cause it to break.
When engaged, the augers rotate and draw snow into the
auger housing.
Chute Assembly
Snow drawn into the auger housing is discharged out the
chute assembly.
Recoil Starter Handle
This handle is used to manually start the engine.
Gas Cap
Unthread the gas cap to add gasoline to the fuel tank.
Electric Starter Button
Pressing the electric starter button engages the engine’s
electric starter when plugged into a 120V power source.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
6. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to FULL and then slowly into
the OFF position again.
Gas & Oil Fill-Up
Service the engine with gasoline and oil as instructed in
the Tecumseh Engines manual packed separately with
your snow thrower. Read instructions carefully.
Starting The Engine
7. When disconnecting the extension cord, always
unplug the end at the three-prong wall outlet before
unplugging the opposite end from the snow thrower.
1. Attach spark plug wire to spark plug. Make certain
the metal loop on the end of the spark plug wire
(inside the rubber boot) is fastened securely over the
metal tip on the spark plug.
WARNING
Recoil Starter
1. Rotate choke control to FULL choke position (cold
engine start).
2. Make certain both the auger control and drive control
are in the disengaged (released) position.
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
3. Move throttle control up to FAST position. Insert
ignition key into slot. Make sure it snaps into place.
Do not attempt to turn the key.
NOTE: If the engine is already warm, place choke control
in the OFF position instead of FULL.
2. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
NOTE: The engine cannot start unless the key is
inserted into ignition switch.
Use extreme care
when handling
NOTE: DO NOT use primer to restart a warm engine after
a short shutdown.
Electric Starter
1. Determine that your home’s wiring is a three-wire
grounded system. Ask a licensed electrician if you
are not certain.
gasoline. Gasoline is
extremely flammable
and the vapors are
explosive. Never fuel
the machine indoors
or while the engine
is hot or running.
Extinguish cigarettes,
cigars, pipes and
other sources of
ignition.
NOTE: Additional priming may be necessary if the
temperature is below 15° Fahrenheit.
WARNING: The optional electric
starter is equipped with a
3. Grasp the recoil starter handle and slowly pull the rope
out. At the point where it becomes slightly harder to
pull the rope, slowly allow the rope to recoil.
grounded three-wire power cord
and plug, and is designed to op-
erate on 120 volt AC household
current. It must be used with a
properly grounded three-prong
receptacle at all times to avoid
the possibility of electric shock.
Follow all instructions carefully
prior to operating the electric
starter.
4. Pull the starter handle with a firm, rapid stroke. Do not
release the handle and allow it to snap back. Keep a
firm hold on the starter handle and allow it to slowly
recoil.
5. As the engine warms, slowly rotate the choke control
to the OFF position. If the engine falters, quickly rotate
the choke control back to the FULL position and then
slowly into the OFF position again.
If your home’s
NOTE: Allow the engine to warm up for a few minutes
after starting. The engine will not develop full power until it
reaches operating temperatures.
wiring system is not a
three-wire grounded
system, do not use
this electric starter
under any conditions.
If you have a grounded three-prong receptacle, proceed
as follows:
1. Plug the extension cord into the outlet located on
the engine’s surface. Plug the other end of extension
cord into a three-prong 120-volt, grounded, AC outlet
in a well-ventilated area.
Stopping The Engine
Run engine for a few minutes before stopping to help dry
off any moisture on the engine.
1. Move throttle control to STOP position.
2. Rotate choke control to FULL choke position (for a
cold engine start).
If your home
2. Remove the ignition key and store in a safe place.
electrical system
is grounded, but a
three-hole receptacle
is not available, do
not use your snow
thrower’s electric
starter.
3. Wipe all snow and moisture from the area around the
engine as well as the area in and around the drive
control and auger control. Also, engage and release
both controls several times.
NOTE: If the engine is already warm, place choke
control in the OFF position instead of FULL.
3. Push the primer two or three times for cold engine
start, making sure to cover vent hole in the center of
the primer when pushing.
NOTE: DO NOT use primer to restart a warm engine
after a short shutdown.
4. Push starter button to start engine.
5. Once the engine starts, release starter button.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Chute Clean-Out Tool
To Engage Augers
The chute clean-out tool is conveniently fastened to the
rear of the auger housing with a mounting clip. Should
snow and ice become lodged in the chute assembly
during operation, proceed as follows to safely clean the
chute assembly and chute opening:
1. To engage the augers and start throwing snow,
squeeze the auger control against the left handle.
Release to stop the augers.
When selecting a
Drive Speed, use the
slower speeds until
you are comfortable
and familiar with the
operation of the snow
thrower.
Auger Control Test
Perform the following test before operating your snow
thrower for the first time and at the start of each winter.
Check the adjustment of the auger control as follows:
1. When the auger control is released and in the
disengaged “up” position, the cable should have very
little slack. It should NOT be tight.
1. Release both the Auger Control and the Drive
Control.
2. Stop the engine by removing the ignition key.
3. Remove the clean-out tool from the clip which
secures it to the rear of the auger housing.
4. Use the shovel-shaped end of the clean-out tool to
dislodge and scoop any snow and ice which has
formed in and near the chute assembly.
2. In a well-ventilated area, start the snow thrower
engine as instructed on the previous page. Make sure
the throttle is set in the FAST position.
NEVER reposition the
shift lever (change
speeds or direction
of travel) without first
releasing the drive
control and bringing
the snow thrower
to a complete stop.
Doing so will result in
premature wear to the
snow thrower’s drive
system.
5. Refasten the clean-out tool to the mounting clip on
the rear of the auger housing, reinsert the ignition key
and start the snow thrower’s engine.
3. While standing in the operator’s position (behind the
snow thrower), engage the auger.
4. Allow the auger to remain engaged for approximately
ten (10) seconds before releasing the auger control.
Repeat this several times.
6. While standing in the operator’s position (behind the
snow thrower), engage the auger control for a few
seconds to clear any remaining snow and ice from the
chute assembly.
5. With the throttle control in the FAST (rabbit) position
and the auger control in the disengaged “up” position,
walk to the front of the machine.
To Engage Drive
6. Confirm that the auger has completely stopped
rotating and shows NO signs of motion. If the auger
shows ANY signs of rotating, immediately return to
the operator’s position and shut off the engine. Wait
for ALL moving parts to stop before re-adjusting the
auger control.
1. With the throttle control in the Fast (rabbit) position,
move shift lever into one of the six forward (F)
positions or two reverse (R) positions. Select a speed
appropriate for the snow conditions and a pace you’re
comfortable with.
2. Squeeze the auger control against the handle and the
augers will turn. Release it and the augers will stop.
7. To readjust the control cable, loosen the upper hex
nut on the auger cable bracket.
3. Squeeze the drive control against the handle the
snow thrower will move. Release it and drive motion
will stop.
8. Position the bracket upward to provide more slack (or
downward to increase cable tension). See Figure 2.
9. Retighten the upper hex nut.
10.Repeat Auger Control Test to verify proper adjust-
ment has been achieved.
WARNING
Never use your hands
to clean snow and
ice from the chute
assembly or auger
housing.
The muffler, engine
and surrounding
areas become hot
and can cause a
burn. Do not touch.
Figure ꢀ
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Control
Refer to Auger Control Test on Page 11 to adjust the
auger control.
4
Shift Cable
If the full range of speeds (forward and reverse) cannot
be achieved, refer to the figures to the right and adjust
the shift cable as follows:
Making
Adjustments
1. Place the shift lever in the fastest forward speed
position.
2. Loosen the hex nut on the shift cable index bracket.
See Figure 3.
3. Pivot the bracket downward to take up slack in the
cable.
4. Retighten the hex nut.
Figure 3
Drive Control
When the drive control is released and in the disen-
gaged “up” position, the cable should have very little
slack. It should NOT be tight.
Check the adjustment of the drive control as follows:
1. With the drive control released, push the snow
thrower gently forward. The unit should roll freely.
WARNING
2. Engage the drive control and gently attempt to push
the snow thrower forward. The wheels should not
turn. The unit should not roll freely.
Read, understand,
and follow all instruc-
tions and warnings
on the machine and
in this manual before
operating.
3. With the drive control released, move the shift lever
back and forth between the R2 position and the F6
position several times. There should be no resistance
in the shift lever.
4. If any of the above tests failed, the drive cable is in
need of adjustment. Proceed as follows:
Never attempt to
make any adjust-
ments while the
engine is running,
except where speci-
fied in operator’s
manual.
5. Loosen the lower hex nut on the drive cable bracket.
See Figure 4.
Figure 4
6. Position the bracket upward to provide more slack (or
downward to increase cable tension).
7. Retighten the upper hex nut.
Chute Assembly
The distance snow is thrown can be adjusted by chang-
ing the angle of the chute assembly. To do so:
1. Stop the engine by removing the ignition key and
loosen the plastic knob found on the left side of the
chute assembly.
2. Pivot the chute upward or downward before retight-
ening the wing knob. See Figure 5.
Figure ꢁ
1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
Skid Shoes
The space between the skid shoes and the ground can
be adjusted. See Figure 6.
•
For close snow removal on a smooth surface, raise
skid shoes higher on the auger housing.
4
•
Use a middle or lower position when the area to be
cleared is uneven, such as a gravel driveway.
Making
Adjustments
To adjust the skid shoes:
1. Loosen the four hex nuts (two on each side) and
carriage bolts. Move skid shoes to desired position.
2. Make certain the entire bottom surface of skid shoe is
against the ground to avoid uneven wear on the skid
shoes.
3. Retighten nuts and bolts securely.
Figure 6
Chute Bracket Adjustment
If the spiral at the bottom of the chute directional control
is not fully engaging with the chute assembly, the chute
bracket can be adjusted. To do so:
1. loosen the two nuts which secure the chute bracket
and reposition it slightly. See Figure 7.
WARNING
2. Retighten the nuts.
Loose gravel can be picked
up and thrown by the auger,
causing injury to the operator
and bystanders and/or
Tire Pressure
Before operating, check tire pressure and reduce pres-
sure to between 15 psi and 20 psi.
If the tire pressure is not equal in both tires, the unit may
pull to one side or the other.
damage to the snow thrower
and surrounding property.
Figure ꢂ
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine maintenance.
ꢁ
Lubrication
Engine
Refer to the separate Tecumseh Engines manual
packed with your unit for all engine lubrication instruc-
tions.
Maintaining
Your Snow
Thrower
Gear Shaft
The gear (hex) shaft should be lubricated at least once
a season or after every 25 hours of operation.
1. Remove the lower frame cover by removing the two
screws which secure it.
2. Apply a light coating of an all-weather multi-purpose
grease to the hex shaft. See Figure 8.
Figure 8
Wheels
At least once a season, remove both wheels. Clean and
coat the axles with a multipurpose automotive grease
before reinstalling wheels.
3HEAR 0IN
3PACERS
"EARING
WARNING
Chute Directional Control
Once a season, the joystick should be lubricated with
petroleum jelly, linseed oil, mineral oil, paraffin wax or
3-in-1 oil.
Before lubricating,
repairing, or inspect-
ing, disengage all
controls and stop
engine. Wait until all
moving parts have
come to a complete
stop.
Auger Shaft
At least once a season, remove the shear pins on auger
shaft. Spray lubricant inside shaft, around the spacers.
Also lubricate the flange bearings found at either end of
the shaft. See Figure 9.
Gear Case
The auger gear case has been filled with grease at the
factory. If disassembled for any reason, lubricate with
two ounces of grease (Part Number 737-0168).
Figure 9
NOTE: Do not overfill the gear case. Damage to the
seals could result. Be sure the vent plug is free of
grease in order to relieve pressure.
Avoid oil spillage on
rubber friction wheel
and aluminum drive
plate.
Shave Plate and Skid Shoes
The shave plate and skid shoes on the bottom of the
snow thrower are subject to wear. They should be
checked periodically and replaced when necessary.
To remove skid shoes:
Do not overfill the gear
case. Damage to the
seals could result.
1. Remove the four carriage bolts and hex flange nuts
which secure them to the snow thrower.
2. Reassemble new skid shoes with the four carriage
bolts (two on each side) and hex flange nuts. Refer
to Figure 10.
./4%ꢀ !UGERS NOT SHOWN FOR CLARITYꢀ
To remove shave plate:
1. Remove the carriage bolts and hex nuts which
attach it to the snow thrower housing.
Figure 10
2. Reassemble new shave plate, making sure heads of
carriage bolts are to the inside of housing. Tighten
securely.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Auger Belt Replacement
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
ꢁ
NOTE: Drain the gasoline from the snow thrower, or
place a piece of plastic under the gas cap.
Maintaining
Your Snow
Thrower
2. Carefully pivot the snow thrower up and forward so
that it rests on the auger housing. Remove the frame
cover from the underside of the snow thrower by
removing four self-tapping screws which secure it.
3. Roll the auger belt off the engine pulley.
4. a. Loosen and remove the shoulder screw which
acts as a belt keeper.
2
b. Unhook the support bracket spring from the
frame.
5. Remove the belt from around the auger pulley, and
slip the belt between the support bracket and the
auger pulley. Reassemble auger belt by following
instructions in reverse order.
NOTE: Although
multi-viscosity oils
(5W30, 10W30 etc.)
improve starting in cold
weather, these multi-
viscosity oils also result
in higher oil consump-
tion when used above
32ºF. Check your snow
thrower’s engine oil
level more frequently to
avoid possible engine
damage from running
low on oil.
NOTE: Do NOT forget to reinstall the shoulder screw
and reconnect the spring to the frame after installing a
replacement auger belt.
3
NOTE: Do not sand-
blast spark plug. Spark
plug should be cleaned
by scraping or wire
brushing and washing
with a commercial
solvent.
4
5
IMPORTANT
NEVER replace the
auger shear pins with
standard pins. Any
A
damage to the auger
gearbox or other com-
ponents, as a result of
doing so, will NOT be
covered by your snow
thrower’s warranty.
B
1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
Augers
•
The augers are secured to the spiral shaft with two
1
shear pins and cotter pins. If the auger should strike a
foreign object or ice jam, the snow thrower is designed
so that the pins may shear. Refer to Figure 9.
ꢁ
•
If the augers will not turn, check to see if the pins have
sheared. One set of replacement shear pins has been
provided with the snow thrower. When replacing pins,
spray an oil lubricant into shaft before inserting new
pins.
Maintaining
Your Snow
Thrower
Drive Belt Replacement
To remove and replace your snow thrower’s auger belt,
proceed as follows:
1. Remove the plastic belt cover on the front of the
engine by removing the two self-tapping screws.
•
Drain the gasoline from the snow thrower, or place a
piece of plastic under the gas cap.
2
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
NEVER replace
the auger shear
2. Remove the frame cover from the underside of the
snow thrower by removing four self-tapping screws
which secure it.
pins with anything
other than OEM
3. a. Grasp the idler pulley and pivot it toward the right.
b. Roll the auger belt off the engine pulley.
c. Lift the drive belt off engine pulley.
Part No.738-04124
replacement shear
pins. Any damage to
the auger gearbox
or other components
as a result of failing
to do so will NOT be
covered by your snow
thrower’s warranty.
4. Slip the drive belt off the pulley and between friction
wheel and friction wheel disc.
•
Remove and replace belt in the reverse order.
3
4
B
C
A
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Friction Wheel Removal
If the snow thrower fails to drive with the drive control
engaged, and performing the drive control cable adjust-
ment on page 14 fails to correct the problem, the friction
wheel may need to be replaced. Follow the instructions
below. Examine the friction wheel for signs of wear or
cracking and replace if necessary
1
ꢁ
•
Place the shift lever in third Forward (F3) position.
Maintaining
Your Snow
Thrower
•
Drain the gasoline from the snow thrower, or place a
piece of plastic under the gas cap.
•
Carefully pivot the snow thrower up and forward so
that it rests on the auger housing.
1. a. Remove the frame cover from the underside of
the snow thrower by removing four self-tapping
screws which secure it.
b. Remove the right-hand wheel by removing the
screw and bell washer which secure it to the axle.
2. Carefully remove the hex nut and washer which
secures the hex shaft to the snow thrower frame and
lightly tap the shaft’s end to dislodge the ball bearing
from the right side of the frame.
When reassembling
the friction wheel as-
sembly, tighten each
screw only one rota-
tion before turning the
wheel clockwise and
proceeding with the
next screw. Repeat
this process several
times to ensure the
plates are secured
with equal force.
3. Carefully position the hex shaft downward and to
the left before carefully sliding the friction wheel
assembly off the shaft.
2
NOTE: If you’re replacing the friction wheel assembly
as a whole, discard the worn part and slide the new part
onto the hex shaft. Follow the steps above in reverse
order to reassemble components. If you’re disassem-
bling the friction wheel and replacing only the rubber
ring, proceed as follows:
4. Remove the four screws which secure the friction
wheel’s side plates together.
•
•
•
Remove the rubber ring from between the plates.
Reassemble the side plates with a new rubber ring.
Slide the friction wheel assembly back onto the hex
shaft and follow the steps above in reverse order to
reassemble components.
NEVER replace
the auger shear
pins with anything
other than OEM
3
4
Part No.738-04124
replacement shear
pins. Any damage to
the auger gearbox
or other components
as a result of failing
to do so will NOT be
covered by your snow
thrower’s warranty.
1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
If the snow thrower will not be used for 30 days or longer, or if it is the end of the snow season when the last pos-
sibility of snow is gone, the equipment needs to be stored properly. Follow storage instructions below to ensure top
performance from the snow thrower for many more years.
ꢂ
Preparing Engine
Preparing Snow Thrower
NOTE: Refer to the engine manual for more detailed
information on preparing the snow thrower engine for
storage.
•
When storing the snow thrower in an unventilated or
metal storage shed, care should be taken to rustproof
the equipment. Using a light oil or silicone, coat the
equipment, especially any chains, springs, bearings
and cables.
Off-Season
Storage
Short-Term Storage
It is important to prevent gum deposits from forming in
essential fuel system parts of the engine such as the
carburetor, fuel filter, fuel hose, or tank during short-term
storage (15-30 days). To prevent this, treat the fuel
system using a fuel stabilizer.
•
•
•
Remove all dirt from exterior of engine and equipment.
Follow lubrication recommendations.
Store equipment in a clean, dry area.
Fuel stabilizer (such as STA-BIL™ or ULTRA-FRESH™)
is an acceptable alternative in minimizing the formation
of fuel gum deposits during storage. Add stabilizer to
gasoline in fuel tank or storage container. Always follow
mix ratio found on stabilizer container. Run engine at least
10 minutes after adding stabilizer to allow it to reach the
carburetor.
WARNING
Never store snow thrower
with fuel in tank indoors
or in poorly ventilated
areas, where fuel fumes
may reach an open flame,
spark or pilot light as on
a furnace, water heater,
clothes dryer or
WARNING: Never store snow thrower
with fuel in tank indoors or in poorly
ventilated areas, where fuel fumes may
reach an open flame, spark or pilot
light as on a furnace, water heater, clothes dryer or
gas appliance.
gas appliance.
CAUTION: Alcohol blended fuels
(called gasohol or using ethanol or
methanol) can attract moisture which
leads to separation and formation of
Fuel left in engine during
warm weather deteriorates
and will cause serious
starting problems.
acids during storage. Acidic gas can damage the fuel
system of an engine while in storage.
Long-Term Storage
Never use engine or carbu-
retor cleaning products in
the fuel tank or permanent
damage may occur.
To avoid engine problems, the fuel system should be
emptied before storage for 30 days or longer.
WARNING: Fuel left in engine during
warm weather deteriorates and will
cause serious starting problems.
1. Run the engine until the fuel tank is empty and it stops
due to lack of fuel. Do not attempt to pour fuel from the
engine.
WARNING: Never use engine or carbu-
retor cleaning products in the fuel tank
or permanent damage may occur.
2. Remove the spark plug and pour one (1) ounce of
engine oil through the spark plug hole into the cylinder.
Cover spark plug hole with a rag and crank the engine
several times to distribute the oil. Replace spark plug.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Problem
Engine fails to start
Cause
1. Choke not in ON position.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not primed.
Remedy
1. Move choke to ON position.
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
8
4. Prime engine as instructed in
“Operating Your Snow Thrower”.
Trouble-
Shooting
5. Clean, adjust gap, or replace.
6. Clean fuel line.
5. Faulty spark plug.
6. Blocked fuel line.
7. Insert key fully into the switch.
7. Safety key not in ignition on engine.
1. Unit running on CHOKE.
1. Move choke lever to OFF position.
Engine runs erratic
2. Clean fuel line; fill tank with clean,
fresh gasoline.
2. Blocked fuel line or stale fuel.
3. Water or dirt in fuel system.
4. Carburetor out of adjustment.
NOTE: This section
addresses minor
3. Drain fuel tank. Refill with
fresh fuel.
service issues. For
further details, contact
a MTD authorized
service center or call
1 (800) 800-7310 for
assistance.
4. Contact MTD Service Center.
1. Carburetor not adjusted properly.
1. Loose parts or damaged auger.
1. Contact MTD Service Center.
Engine overheats
1. Stop engine immediately and
disconnect spark plug wire. Tighten
all bolts and nuts. If vibration
continues, have unit serviced by a
MTD Service Center.
Excessive
Vibration
Loss of power
1. Spark plug wire loose.
2. Gas cap vent hole plugged.
3. Exhaust port plugged.
1. Connect and tighten spark plug
wire.
2. Remove ice and snow from gas
cap. Be certain vent hole is clear.
3. Contact MTD Service Center.
1. Drive control cable in need of adjust-
ment.
1. Adjust drive control cable. Refer to
“Making Adjustments”.
Unit fails
to propel itself
2. Drive belt loose or damaged.
2. Replace drive belt.
1. Chute assembly clogged.
1. Stop engine immediately and
disconnect spark plug wire. Clean
chute assembly and inside of auger
housing with clean-out tool or a
stick.
Unit fails
to discharge snow
2. Foreign object lodged in auger.
2. Stop engine immediately and
disconnect spark plug wire.
Remove object from auger with
clean-out tool or a stick.
3. Auger control cable in need of adjust-
ment.
3. Refer to “Auger Control Test” on
page 11.
4. Auger belt loose or damaged.
5. Shear pin(s) sheared.
4. Refer to Maintenance section.
5. Replace with new shear pin(s).
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles E & F
ꢀ
ꢇꢈ
ꢇꢃ
ꢂ
ꢁ
ꢁꢉ
ꢇꢆ
ꢁꢅ
ꢃ
ꢇꢅ
ꢅꢅ
ꢅꢈ
ꢁꢈ
ꢄ
ꢅ
ꢁꢇ
ꢇꢂ
ꢁꢃ
ꢁ
ꢈ
ꢀ
ꢈ
ꢉ
ꢇꢉ
ꢅ
ꢇ
ꢄ
ꢄ
ꢂꢃ
ꢂꢅ
ꢈꢃ
ꢈꢉ
ꢈꢅ
ꢅꢇ ꢅꢁ
ꢂꢀ
ꢂꢄ
ꢈꢀ
ꢈꢆ
ꢅꢆ
ꢈꢄ
ꢅꢂ
ꢈꢈ
ꢈꢁ
ꢈꢂ
ꢂꢂ
ꢇꢄ
ꢂꢁ
ꢂꢉ
ꢂꢂ
ꢂꢂ
ꢈꢇ
ꢇꢁ
ꢂꢁ
ꢇꢀ
ꢂꢈ
ꢂꢂ
ꢁꢆ
ꢂꢇ
ꢇꢇ
ꢀ
ꢁꢀ
ꢀ0
Download from Www.Somanuals.com. All Manuals Search And Download.
1. 731-2635
Snow Removal Tool Mount
29. 684-04107 Spiral Assembly, LH
30. 684-04108 Spiral Assembly, RH
31. 731-04870* Spacer, 1.25 OD x .75 ID x 1.00
2. 684-04057 Impeller Assembly, 12” Dia.
3. 710-0347
4. 710-0451
Hex Screw, 3/8-16, 1.75, Gr5
9
Bolt, Carriage, 5/16-18, .750 Gr1
32. 736-0188
Washer, Flat, .76 x 1.49 x .06
5. 710-0604A Screw, 5/16-18, 0.625
33. 741-0493A Bushing, Flange, .80 ID x .91 OD
34. 790-00087A Housing, 1” Hex Bearing
6. 710-0703
Screw, Carriage, 1/4-20, .750, Gr5
Illustrated
Parts List
7. 712-04063 Nut, Flange Lock, 5/16-18, Nylon
8. 712-04064 Nut, Flange Lock, 1/4-20, Nylon
9. 712-04065 Nut, Flange Lock, 3/8-16, Nylon
10. 714-04040 Cotter Pin, Bow-tie
35. 790-00117
Shave Plate, 2.25 x 21.66
790-00120 Shave Plate, 2.25 x 23.66
790-00121 Shave Plate, 2.25 x 25.66
790-00118
36. 784-5580
37. 719-0319
38. 719-0320
39. 721-0179
40. 741-0662
41. 710-0642
42. 711-04286
711-04285
Shave Plate, 2.25 x 27.66
Slide Shoe
11. 725-0157
Cable, Tie, 3/16 x .05 x 7.4
12. 726-04012 Nut, Push-on, .25 Dia
Housing, Auger, RH Reduced
Housing, Auger, LH Reduced
Seal, Oil, .750 ID
13. 731-04705
14. 732-0611
15. 736-0174
16. 736-0242
17. 736-0463
18. 731-2643
19. 738-0143
20. 738-0281
Chute, Adapter 5” Dia
Spring, Extension, .38 OD x 3.6
Washer, Wave, .625 x .885 x .015
Washer, Bell, .340 x .872 x .060
Washer, Flat, .25 x .630 x .0515
Snow Removal Tool
Bearing, Flange, .75 x 1.0 x .59
Screw, Self-tapping, 1/4-20, 0.750
Axle, Auger, 22”
To order replacement
parts, call
1-800-800-7310
or visit us on
Axle, Auger, 24”
Screw, Shoulder, .498 x .34, 3/8-16
Screw, Shoulder, .625 x .17, 3/8-16
711-04284
Axle, Auger, 26”
the web at
711-04283
Axle, Auger, 28”
21. 738-04124A Shear Pin, .25 x 1.50
43. 714-0161
Key, Hi-pro 3/16 x 5/8
22. 741-0245
23. 741-0309
Bearing, Hex Flange x .75 ID
Bearing, Ball, .75 ID x 1.85 OD
44. 715-04021 Pin, Dowel, .25 OD x 1.2
45. 717-04126 Shaft, Worm .75 OD
46. 717-0528A Gear, Worm 20T
24. 756-0981B Flat Pulley, Idler, 2.75 OD
25. 790-00075 Housing, Bearing, 1.85 ID
26. 790-00080A Bracket, Auger Idler w/ Brake
47. 718-04071
48. 721-0325
49. 721-0327
50. 736-0351
51. 736-3084
52. 741-0663
53. 741-0661A
Collar, Thrust
Plug, 1/4 x .437
27. 618-04170
618-04171
Gearbox Assembly, Auger, 22”
Gearbox Assembly, Auger, 24”
Gearbox Assembly, Auger, 26”
Gearbox Assembly, Auger, 28”
Seal, Oil, .75 x 1 x .131
Washer, Flat, .760 ID x 1.5 OD
Washer, Flat, .51 x 1.12
Bearing, Flange, .75 x 1.0 x .925
Bearing, Flange, .75 x 1.00 x .975
618-04172
618-04173
28. 684-04067 Housing Assembly, Auger 22”
684-04069 Housing Assembly, Auger 24”
684-04071 Housing Assembly, Auger 26”
684-04073 Housing Assembly, Auger 28”
54. 746-04230 Clutch Cable, Auger, 47.23”
55. 629-0071 Extention Cord, 110V
* None found between spirals on models with 22-inch auger housing.
* One found between spirals on models with 24-inch auger housing.
* Two found between spirals on models with 26-inch auger housing.
* Three found between spirals on models with 28-inch auger housing.
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured
on the previous page are standard equipment.
ꢀ1
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles E & F
ꢇ
ꢂꢄ
ꢂꢃ
ꢂꢇ
ꢀꢁ
ꢈ
ꢂꢉ
ꢀ
ꢉ
ꢂꢂ
ꢀꢀ
ꢀꢅ
ꢄꢀ
ꢄꢅ
ꢀꢂ
ꢉ
ꢇꢆ
ꢇꢂ
ꢂꢈ
ꢂꢇ
ꢂꢁ
ꢄꢇ
ꢅ
ꢆ
ꢂꢅ
ꢀꢆ
ꢀꢈ
ꢂ
ꢁ
ꢄ
ꢀꢃ
ꢇꢁ
ꢅꢁ
ꢇꢇ
ꢁ
ꢇꢃ
ꢄꢃ
ꢅꢃ
ꢀꢄ
ꢅꢀ
ꢀꢇ
ꢂꢆ
ꢂꢀ
ꢅꢄ
ꢅꢇ
ꢇꢄ
ꢅꢅ
ꢂꢀ
ꢄꢂ
ꢇꢄ
ꢀꢉ
ꢅꢆ
ꢅꢈ
ꢇꢅ
ꢇꢈ
ꢇꢀ
ꢅꢉ
ꢂꢀ
ꢀꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
1. 631-04133
Handle Assembly, Clutch Lock, LH
27. 731-04869 Chute, Flange Keeper
28. 746-04228 Cable, Speed Selector
2. 631-04134A Handle Assembly, Clutch Lock, RH
3. 684-04105A Handle Ass’y, Engage, Black, LH
684-04110A Handle Ass’y, Engage, Yellow, LH
4. 684-04106B Handle Ass’y, Engage, Black, RH
684-04109B Handle Ass’y, Engage, Yellow, RH
29. 746-0605
30. 747-04263
Houlder, Cable Barrel, LH
Eye Bolt, Chute Crank
9
31. 790-00202 Shift Lever
32. 731-04912A Chute, Lower, 5.0 Dia.
Illustrated
Parts List
5. 710-0224
Screw, #10-16, 0.500
33. 710-0276
34. 710-04071 Bolt, Carriage, 5/16-18, 1.0
35. 710-0451 Bolt, Carriage, 5/16-18, .750
36. 731-04426A Chute, Upper, w/ Label
Bolt, Carriage, 5/16-18, 1.0
6. 710-04326 Screw, #8-16 x .50
7. 710-04354 Screw, 1/4-20, .375
8. 710-0606
Hex Screw, 1/4-20, 1.50, Gr5
9. 790-00219 Panel, Handle, (no cutout) E-Style
790-00209 Panel, Handle, (w/ cutout) F-Style
37. 736-0159
38. 741-0475
39. 784-5647
Washer, .349 x .879 x .063
Bushing, Plastic, .380
Bracket, Chute Crank
10. 710-1233
11. 711-04287
Screw, Machine, #10-24, 1.375
Pivot Rod
40. 684-04104 Crank Assembly, Chute
12. 712-04063 Nut, Flange Lock, 5/16-18, Nylon
13. 712-04064 Nut, Flange Lock, 1/4-20, Nylon
14. 712-04081A Nut, Hex, 1/4-20, Shoulder
41. 710-0449
42. 710-1260A
43. 714-0104
Screw, Carriage, 5/16-18, 2.25
Screw, 5/16-18, 0.75, Gr5
Pin, Cotter, .072 x 1.13
To order replacement
parts, call
1-800-800-7310
or visit us on
15. 720-0274
Grip, 1.0 ID x 5.0
44. 720-0201A Crank Knob, 1.0 Dia. x 3.2, Black
45. 720-04072 Knob, 5/16-18, Black
720-04071 Knob, 5/16-18, Yellow
16. 720-04039 Knob, Shift, Black
720-04046 Knob, Shift, Yellow
17. 731-04894B Lock Plate
the web at
46. 726-0100
47. 735-0234
48. 736-0185
49. 749-04141
50. 749-04142
51. 749-04138
52. 747-1136
53. 725-1658
54. 725-1672
Cap, Push, 3/8 Rod
18. 731-04896A Cam, Clutch Lock
Grommet, .44 ID x .94 OD x .50
Washer, Flat, .375 x .738 x .063
Handle, Upper, RH
19. 732-0193
20. 732-04219
Spring, .39 x .60 x .88
Spring, Clutch Lock
21. 732-04238 Spring, Torsion, 0.8156 ID x .3038
22. 725-04220 Wire Harness, Lamp
Handle, Upper, LH
Handle, Lower
23. 735-0199A Bumper, Rubber, .62 OD x .22
Retainer, Lens
24. 736-0262
25. 738-04118
Washer, Flat, .385 x .870 x .092
Bolt, Shoulder, 5/16-18 x 0.905
Lamp, Halogen, 12V, 27W
Lens Assembly, Lamp
26. 738-04122 Screw, Shoulder, .43 x 1.3, 1/4-20
NOTE: A lamp cannot be added to a unit that did come come factory-equipped with a lamp.
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured
on the previous page are standard equipment.
ꢀ3
Download from Www.Somanuals.com. All Manuals Search And Download.
Styles E & F
46
48
55
53 61
50
42
62
B
39
63
45
40
7
60
60
54
59
1
59
49
47
41
57
56
22
B
44
51
53
21
43
5
2
58
23
7
45
67
52
64
69
28
65
34
8
23
24 30
26
16
10
7
20
68
12
70
38
33
4
11
66
30
A
24
15
23
2
25
36
37
1
19
29
26
7
13
14
6
5
A
31
17
9
3
18
30
24
35
27
7
ꢀ4
Download from Www.Somanuals.com. All Manuals Search And Download.
1. 656-04025A Disc Assembly, Friction Wheel
2. 684-04153 Friction Wheel Assembly, 5.5 OD
3. 684-04154 Support Bracket, Friction Wheel
4. 684-04156 Shift Assembly, Rod
37. 731-04873 Spacer, 1.25 x .75 x 3.0
731-04877* Spacer, 1.25 x .75 x 1.50
38. 738-04168 Axle, .75 x 22”
9
39. 741-0919
40. 710-0106
41. 710-0191
Ball Bearing
5. 710-0627
6. 710-0788
7. 710-0896
Hex Screw, 5/16-24, .750, Gr5
Screw, 1/4-20, 1.000
Hex Screw, 1/4-20, 1.25, Gr5
Hex Screw, 3/8-24, 1.25, Gr8
Illustrated
Parts List
Screw, 1/4-14 x .625
42. 710-04520 Hex Screw, 5/16-24, 1.25, Gr5
43. 710-0654A Screw, Sems, 3/8-16, 1.00
8. 712-04065 Nut, Flange Lock, 3/8-16, Nylon
9. 712-0413
10. 714-0126
11. 716-0104
12. 716-0136
13. 716-0231
14. 717-04209
15. 717-04230
16. 726-0221
17. 732-0264
18. 736-0242
19. 736-0287
20. 736-04161
Nut, Jam Lock, 5/8-18, Gr5, Nylon
Key, Hi Pro, 3/16 x 3/4 Dia.
E-ring, .500 Dia.
44. 710-1245B
Hex Screw, 5/16-24, .875, Gr8
45. 712-04064 Nut, Flange Lock, 1/4-20, Nylon
46. 726-04012 Nut, Push-on, .25 Dia.
47. 731-04792A Cover, Belt
E-ring, Retaining, .875 Dia.
E-ring, .750 Dia.
48. 732-04308 Spring, Torsion, .850 ID x .354
Hex Shaft, .8125, 7-Tooth
Gear, 80-Tooth
49. 736-0247
50. 736-0119
51. 736-0505
Washer, Flat, .406 x 1.25 x .157
Washer, Lock .3125
To order replacement
parts, call
Speed Nut, .500
Washer, Flat, .34 x 1.50 x .150
Extension Spring
52. 748-04053 Pulley, Adapter, .75 Dia.
1-800-800-7310
or visit us on
Washer, Bell, .340 x .872 x .060
Washer, Flat, .793 x 1.24 x .060
Washer, Flat, .75 x 1.00 x .060
53. 748-04112
Spacer, Shoulder, .317 x .50 x .102
54. 750-04303 Spacer, .875 ID x 1.185 OD
55. 750-04477 Spacer, .340 x .750 x .360
56. 754-04050 Belt, Auger Drive
57. 754-04088 Belt, Wheel Drive
58. 756-04109 Pulley, Auger Drive, 8.1 x .5
the web at
21. 738-04164A Pin, Friction Disc
22. 741-04098
Ball Bearing, 30 x 55 x 13
23. 738-04184A Screw, Shoulder, .37 x .105, 1/4-20
24. 738-0924A Screw, 1/4-28, .375
59. 756-04113
60. 756-04179
Pulley, Half, V x 2.600 OD
Pulley, Half, 1/4-V x 1.5 OD
25. 741-0245
26. 741-0563
Bearing, Hex Flange x .75 ID
Bearing, Ball, 17 x 40 x 12
61. 790-00208 Idler Bracket, Wheel Drive
62. 790-00230 Sleeve, Bearing Idler
27. 746-04229 Clutch Cable, Wheel, 44.95”
28. 746-04228 Cable, Speed Selector
63. 750-04571 Spacer, Shoulder, .26 x .79 x .538
64. 735-04054 Rubber, Friction Wheel, 5.5 OD
29. 748-0190
30. 756-0625
Spacer, .508 ID x .75 OD x .68
Roller, Cable
65. 710-0751
66. 732-04311
Hex Screw, 1/4-20, .620, Gr5
Spring, Torsion, .750 ID x .968
31. 790-00096 Front Guide Bracket, Auger Cable
32. 790-00180 Frame
67. 712-04063 Nut, Flange Lock, 5/16-18, Nylon
68. 790-00156 Bracket, Shift Spacer
33. 790-00206A Guide Bracket, Auger Cable
34. 790-00207A Guide Bracket, Drive Cable
35. 790-00226 Cover, Frame
* Found on models with a
22-inch auger housing only
69. 790-00217A Pivot Bracket, Speed Selector
70. 790-00218A Shift Bracket, Speed Selector
36. See Chart
Wheel Assembly
** The wheel axle is mounted
in the frame side’s
Wheel Assembly
634-04144
Wheel Size
Rim Only
634-04151
Tire Only
734-1732
Valve Only
734-0255
upper hex-hole on models
equipped with 16-inch
wheels.
13 x 4
13 x 5
15 x 5
16 x 4.8
634-04143
634-04151
634-04151
634-04140
734-1527
734-1859
734-1530
734-0255
734-0255
734-0255
634-04142
634-04141**
NOTE: Snow thrower features and components vary by model. NOT all parts listed above and pictured
on the previous page are standard equipment.
ꢀꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
ꢀ6
Download from Www.Somanuals.com. All Manuals Search And Download.
NOTES
ꢀꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR
The limited warranty set forth below is given by MTD LLC with respect
to new merchandise purchased and used in the United States, its
possessions and territories.
e. MTD does not extend any warranty for products sold or exported
outside of the United States, its possessions and territories, except
those sold through MTD’s authorized channels of export distribution.
“MTD” warrants this product against defects in material and workman-
ship for a period of two (2) years commencing on the date of original
purchase and will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This limited war-
ranty shall only apply if this product has been operated and maintained
in accordance with the Operator’s Manual furnished with the product,
and has not been subject to misuse, abuse, commercial use, neglect,
accident, improper maintenance, alteration, vandalism, theft, fire, water,
or damage because of other peril or natural disaster. Damage resulting
from the installation or use of any part, accessory or attachment not
approved by MTD for use with the product(s) covered by this manual
will void your warranty as to any resulting damage.
Normal wear parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batter-
ies, belts, blades, blade adapters, grass bags, rider deck wheels, seats,
snow thrower skid shoes, shave plates, auger spiral rubber and tires.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area, check your Yellow Pages,
or contact MTD LLC at P.O. Box 361131, Cleveland, Ohio 44136-
0019, or call 1-800-800-7310 or 1-330-220-4683 or log on to our
f. Replacement parts that are not genuine MTD parts.
g. Transportation charges and service calls.
No implied warranty, including any implied warranty of mer-
chantability of fitness for a particular purpose, applies after the
applicable period of express written warranty above as to the
parts as identified. No other express warranty, whether written or
oral, except as mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product, shall
bind MTD. During the period of the warranty, the exclusive remedy
is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. MTD shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn
care services or for rental expenses to temporarily replace a
warranted product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of
the product shall void this warranty. You assume the risk and liability
for loss, damage, or injury to you and your property and/or to others and
their property arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
This limited warranty does not provide coverage in the following cases:
a. The engine or component parts thereof. These items may carry a
separate manufacturer’s warranty. Refer to applicable manufacturer’s
warranty for terms and conditions.
b. Log splitter pumps, valves, and cylinders have a separate one year
warranty.
c. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments, deck
adjustments, and normal deterioration of the exterior finish due to
use or exposure.
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
d. Service completed by someone other than an authorized service
dealer.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-ꢂ310, 1-330-ꢀꢀ0-4683
Download from Www.Somanuals.com. All Manuals Search And Download.
|