Safety • Assembly • Operation • Tips & Techniques • Maintenance • Troubleshooting • Parts Lists • Warranty
OPERATOR’S MANUAL
21” Rotary Mower — Model Series 410 thru 420
IMPORTANT
READ SAFETY RULES AND INSTRUCTIONS CAREFULLY BEFORE OPERATION
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-covered, brush-
covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting applicable local or state laws (if any).
If a spark arrester is used, it should be maintained in effective working order by the operator. In the State of California the above is required by law
(Section 4442 of the California Public Resources Code). Other states may have similar laws. Federal laws apply on federal lands. A spark arrester
for the muffler is available through your nearest engine authorized service dealer or contact the service department, P.O. Box 361131 Cleveland,
Ohio 44136-0019.
FORM NO. 769-02336A
9/25/2006
PRINTED IN U.S.A.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
Download from Www.Somanuals.com. All Manuals Search And Download.
Use this page as a guide to determine slopes where you may not operate safely.
Do not operate your lawn mower on such slopes.
1
Slope
Gauge
WARNING
Do not mow on inclines
with a slope in excess
of 15 degrees (a rise
of approximately
2-1/2 feet every 10
feet). A riding mower
could overturn and
cause serious injury.
If operating a walk-
behind mower on such
a slope, it is extremely
difficult to maintain your
footing and you could
slip, resulting in serious
injury.
Operate RIDING
mowers up and down
slopes, never across
the face of slopes.
Operate
WALK-BEHIND
mowers across the
face of slopes, never
up and down slopes.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Engine Exhaust, some of its constituents, and certain vehicle compo-
nents contain or emit chemicals known to State of California to cause cancer and
birth defects or other reproductive harm.
2
DANGER: This machine was built to be operated according to the rules for safe operation in this
manual. As with any type of power equipment, carelessness or error on the part of the operator
can result in serious injury. This machine is capable of amputating hands and feet and throwing
objects. Failure to observe the following safety instructions could result in serious injury or death.
Safe
Operation
Practices
6. Always wear safety glasses or safety goggles during opera-
Children
tion and while performing an adjustment or repair to protect
Tragic accidents can occur if operator is not alert to presence
of children. Children are often attracted to mower and mowing
your eyes. Thrown objects which ricochet can cause serious
injury to the eyes.
activity.They do not understand the dangers. Never assume
7. Wear sturdy, rough-soled work shoes and close-fitting
slacks and shirts. Shirts and pants that cover the arms and
legs and steel-toed shoes are recommended. Never operate
this machine in bare feet, sandals, slippery or light-weight
(e.g. canvas) shoes.
that children will remain where you last saw them.
1. Keep children out of the mowing area and under watchful
care of a responsible adult other than the operator.
2. Be alert and turn mower off if a child enters the area.
3. Before and while moving backwards, look behind and down
for small children.
4. Use extreme care when approaching blind corners,
doorways, shrubs, trees, or other objects that may obscure
your vision of a child who may run into the mower.
5. Keep children away from hot or running engines.They can
suffer burns from a hot muffler.
8. Do not put hands or feet near rotating parts or under cutting
deck. Contact with blade can amputate hands and feet.
9. A missing or damaged discharge cover can cause blade
contact or thrown object injuries.
WARNING
10. Many injuries occur as a result of the mower being pulled
over the foot during a fall caused by slipping or tripping.
Do not hold on to the mower if you are falling; release the
handle immediately.
6. Never allow children under 14 years old to operate a power
mower. Children 14 years old and over should read and
understand operation instructions and safety rules in this
manual and should be trained and supervised by a parent.
This symbol points
out important safety
instructions which, if
not followed, could
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
instructions in this
11. Never pull the mower back toward you while you are
walking. If you must back the mower away from a wall or
obstruction first look down and behind to avoid tripping and
then follow these steps:
General Operation
1. Read this operator’s manual carefully in its entirety before
attempting to assemble this machine. Read, understand,
and follow all instructions on the machine and in the
manual(s) before operation. Be completely familiar with
the controls and the proper use of this machine before
operating it. Keep this manual in a safe place for future
and regular reference and for ordering replacement parts.
2. This machine is a precision piece of power equipment,
not a plaything. Therefore, exercise extreme caution at all
times. Your unit has been designed to perform one job: to
mow grass. Do not use it for any other purpose.
a. Step back from mower to fully extend your arms.
b. Be sure you are well balanced with sure footing.
c. Pull the mower back slowly, no more than half way
toward you.
d. Repeat these steps as needed.
12. Do not operate the mower while under the influence of
alcohol or drugs.
manual before at-
tempting to operate
this machine. Failure
to comply with these
instructions may result
in personal injury. When
you see this symbol.
13. Do not engage the self-propelled mechanism on units so
equipped while starting engine.
14. The blade control handle is a safety device. Never attempt
to bypass its operation. Doing so makes the safety device
inoperative and may result in personal injury through
contact with the rotating blade. The blade control handle
must operate easily in both directions and automatically
return to the disengaged position when released.
15. Never operate the mower in wet grass. Always be sure of
your footing. A slip and fall can cause serious personal
injury. If you feel you are losing your footing, release the
blade control handle immediately and the blade will stop
rotating within three seconds.
3. Never allow children under 14 years old to operate this
machine. Children 14 years old and over should read and
understand the instructions in this manual and should
be trained and supervised by a parent. Only responsible
individuals who are familiar with these rules of safe
operation should be allowed to use this machine.
4. Thoroughly inspect the area where the equipment is to
be used. Remove all stones, sticks, wire, bones, toys
and other foreign objects, which could be tripped over or
picked up and thrown by the blade. Thrown objects can
cause serious personal injury. Plan your mowing pattern
to avoid discharge of material toward roads, sidewalks,
bystanders and the like. Also, avoid discharging material
against a wall or obstruction, which may cause discharged
material to ricochet back toward the operator.
HEED ITS WARNING!
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
16. Mow only in daylight or good artificial light. Walk, never run.
17. Stop the blade when crossing gravel drives, walks or roads.
18. If the equipment should start to vibrate abnormally, stop the
engine and check immediately for the cause. Vibration is
generally a warning of trouble.
and follow the warnings
and instructions
in this manual
5. To help avoid blade contact or a thrown object injury,
stay in operator zone behind handles and keep children,
bystanders, helpers and pets at least 75 feet from mower
while it is in operation. Stop machine if anyone enters
area.
and on the machine.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
19. Shut the engine off and wait until the blade comes to a
complete stop before removing the grass catcher or unclog-
ging the chute.
6. Extinguish all cigarettes, cigars, pipes and other sources
of ignition.
7. Never fuel machine indoor because flammable vapors will
accumulate in the area.
The cutting blade continues to rotate for a few seconds after
the engine is shut off. Never place any part of the body in
the blade area until you are sure the blade has stopped
rotating.
8. Never remove gas cap or add fuel while engine is hot or
running. Allow engine to cool at least two minutes before
refueling.
2
20. Never operate mower without proper trail shield, discharge
cover, grass catcher, blade control handle or other safety
protective devices in place and working. Never operate
mower with damaged safety devices. Failure to do so can
result in personal injury.
9. Never over fill fuel tank. Fill tank to no more than ½ inch
below bottom of filler neck to provide for fuel expansion.
10. Replace gasoline cap and tighten securely.
11. If gasoline is spilled, wipe it off the engine and equipment.
Move unit to another area. Wait 5 minutes before starting
engine.
Safe
Operation
Practices
21. Muffler and engine become hot and can cause a burn. Do
not touch.
12. Never store the machine or fuel container near an open
flame, spark or pilot light as on a water heater, space
heater, furnace, clothes dryer or other gas appliances.
13. To reduce fire hazard, keep mower free of grass, leaves,
or other debris build-up. Clean up oil or fuel spillage and
remove any fuel soaked debris.
22. Only use parts and accessories made for this machine by
manufacturer. Failure to do so can result in personal injury.
23. If situations occur which are not covered in this manual,
use care and good judgment. Contact your dealer for
assistance.
14. Allow a mower to cool at least 5 minutes before storing.
Slope Operation
General Service:
Slopes are a major factor related to slip and fall accidents, which
can result in severe injury. Operation on slopes requires extra
caution. If you feel uneasy on a slope, do not mow it. For your
safety, use the slope gauge included as part of this manual to
measure slopes before operating this unit on a sloped or hilly
area. If the slope is greater than 15 degrees, do not mow it.
1. Never run an engine indoors or in a poorly ventilated area.
Engine exhaust contains carbon monoxide, an odorless
and deadly gas.
WARNING
2. Before cleaning, repairing, or inspecting, make certain the
blade and all moving parts have stopped. Disconnect the
spark plug wire and ground against the engine to prevent
unintended starting.
This symbol points
Do:
out important safety
instructions, which if
not followed, could
1. Mow across the face of slopes; never up and down. Exercise
extreme caution when changing direction on slopes.
2. Watch for holes, ruts, rocks, hidden objects, or bumps
which can cause you to slip or trip. Tall grass can hide
obstacles.
3. Check the blade and engine mounting bolts at frequent
intervals for proper tightness. Also, visually inspect blade
for damage (e.g., bent, cracked, worn) Replace blade with
the original equipment manufacture’s (O.E.M.) blade only,
listed in this manual. “Use of parts which do not meet the
original equipment specifications may lead to improper
performance and compromise safety!”
4. Mower blades are sharp and can cut. Wrap the blade or
wear gloves, and use extra caution when servicing them.
5. Keep all nuts, bolts, and screws tight to be sure the equip-
ment is in safe working condition.
6. Never tamper with safety devices. Check their proper
operation regularly.
7. After striking a foreign object, stop the engine, discon-
nect the spark plug wire and ground against the engine.
Thoroughly inspect the mower for any damage. Repair the
damage before starting and operating the mower.
endanger the personal
safety and/or property
of yourself and others.
Read and follow all
3. Always be sure of your footing. A slip and fall can cause
serious personal injury. If you feel you are losing your
balance, release the blade control handle immediately, and
the blade will stop rotating within 3 seconds.
instructions in this man-
ual before attempting to
operate this machine.
Failure to comply with
these instructions may
result in personal injury.
When you see this
Do Not:
1. Do not mow near drop-offs, ditches or embankments, you
could lose your footing or balance.
2. Do not mow slopes greater than 15 degrees as shown on
the slope gauge.
3. Do not mow on wet grass. Unstable footing could cause
slipping.
8. Never attempt to make a wheel or cutting height adjust-
ment while the engine is running.
Service
Safe Handling Of Gasoline:
1. To avoid personal injury or property damage use extreme
care in handling gasoline. Gasoline is extremely flammable
and the vapors are explosive. Serious personal injury can
occur when gasoline is spilled on yourself or your clothes,
which can ignite. Wash your skin and change clothes
immediately.
symbol.
HEED IT’S WARNING!
9. Grass catcher components, discharge cover, and trail
shield are subject to wear and damage which could
expose moving parts or allow objects to be thrown. For
safety protection, frequently check components and re-
place immediately with original equipment manufacturer’s
(O.E.M.) parts only, listed in this manual. “Use of parts
which do not meet the original equipment specifications
may lead to improper performance and compromise
safety!”
Your Responsibility
Restrict the use
of this power machine
to persons who read,
understand
2. Use only an approved gasoline container.
3. Never fill containers inside a vehicle or on a truck or trailer
bed with a plastic liner. Always place containers on the
ground away from your vehicle before filling.
4. Remove gas-powered equipment from the truck or trailer
and refuel it on the ground. If this is not possible, then refuel
such equipment on a trailer with a portable container, rather
than from a gasoline dispenser nozzle.
10. Do not change the engine governor setting or over-rev the
engine.The governor controls the maximum safe operating
speed of the engine.
and follow the warnings
and instructions
in this manual
11. Maintain or replace safety labels, as necessary.
12. Observe proper disposal laws and regulations. Improper
disposal of fluids and materials can harm the environment.
and on the machine.
5. Keep the nozzle in contact with the rim of the fuel tank or
container opening at all times until fueling is complete. Do
not use a nozzle lock-open device.
ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
IMPORTANT: This unit is shipped without gasoline or
oil in the engine. Fill up gasoline and oil as instructed
in the accompanying engine manual BEFORE operat-
ing your mower.
A
3
1. Remove any packing material which may be between
upper and lower handles.
Setup and
Adjustment
a. Pull up and back on upper handle as shown in
Figure 3-1. Make certain the lower handle is seated
securely into the handle mounting brackets. Do not
crimp cable while lifting the handle up.
b. Tighten star knobs securing upper handle to lower
handle. See Figure 3-1. Make sure that each
carriage bolt is seated properly in the handle.
B
2. Locate the hairpin clip on the weld pin on each side
lower handle.
a. Remove hairpin clip from this hole. Using a pair
of pliers, insert hairpin clip into the hole on pin
closest to the bracket. See Figure 3-2. Repeat on
other side.
Figure 3-1: Unfold handle and tighten hardware.
NOTE: This Operator’s
Manual covers several
models. Lawn Mower
features vary by
model. Not all features
discussed (or engines
pictured) in this manual
are applicable to all
Lawn Mower models.
Hardware Pack
b. Insert a carriage bolt from the hardware pack into
the upper hole on the handle mounting bracket as
shown in Figure 3-2. Secure with one plastic wing
nut, also included in the hardware pack. Repeat on
other side.
Wing Nuts (2) Carriage Bolts (2)
B
3. The rope guide is attached to the right side of the
upper handle. Loosen the wing nut which secures the
rope guide. See Figure 3-3.
NOTE: Stand behind
the mower as if you
were going to operate
it. Your right hand
corresponds to the right
side of the mower; your
left hand corresponds
to the left side of the
mower.
a. Hold blade control against upper handle.
b. Pull starter rope out of the engine. Release blade
control handle.
c. Slip starter rope into rope guide.
d. Tighten wing nut.
A
4. Insert post on cable ties into holes provided on the
lower handle. Pull cable tie tight and trim excess. See
Figure 3-4.
Figure 3-2: Secure lower handle to mounting brackets.
NOTE: Your mower
is shipped with the
handle in the higher
height position.
A
NOTE: Each end of
the lower handle must
be placed in the same
relative position.
B
IMPORTANT
This unit is shipped
without gasoline or
oil in the engine. Fill
up gasoline and oil
as instructed in the
accompanying engine
manual BEFORE
D
C
Figure 3-3: Pull recoil starter through rope guide and tighten.
Figure 3-4: Secure cable to handle using cable ties.
operating your mower.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
5. Follow steps below to assemble the grass catcher
(if needed). Make certain bag is turned right side
out before assembling (warning label will be on the
outside).
3
a. Place bag over frame so that its black plastic side
is at the bottom.
A
b. Slip plastic channel of grass bag over hooks on
the frame. See Figure 3-5. All the plastic channels
except center top of bag attach from outside of
bag.
Setup and
Adjustment
C
c. Attach center top of bag from inside of bag.
6. Follow steps below to attach grass catcher:
a. Lift rear discharge door.
B
b. Place grass catcher on the pivot rod. Let go
of discharge door so that it rests on the grass
catcher. See Figure 3-6.
Figure 3-5: Assemble the grass catcher (if needed).
To remove grass catcher, lift rear discharge door on the
mower. Lift grass catcher up and out, off of the pivot
rod. Release rear discharge door to allow it to close rear
opening of mower.
WARNING
WARNING: Never operate mower unless the
hooks on the grass catcher are firmly seated
on the pivot rod and the rear discharge door rests
firmly against top of the grass catcher.
Never operate mower
unless the hooks on the
grass catcher are firmly
seated on the pivot rod
and the rear discharge
door rests firmly against
top of the grass catcher.
B
A
Adjustments
An adjusting plate and thumb lever at each wheel
provides cutting height adjustment.
1. Depress lever towards wheel.
2. Move it to any one of the positions for desired cutting
height. See Figure 3-7. Make sure that each wheel is
positioned at the same height.
Figure 3-6: Attach the grass catcher.
3. Release lever towards mower deck.
2
1
3
Figure 3-7: Use adjustment levers at each wheel to change the
cutting height.
ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
KnowYour Lawn Mower
Blade Control
4
Operating
Your Lawn
Mower
Recoil Starter
Cutting Height Adjustment
Levers (one at each wheel)
WARNING
The blade control is a
safety device. DO NOT
bypass its operations.
Use extreme care when
handling gasoline.
Figure 4-1:The main components on the mower.
Gasoline is extremely
flammable and the vapors
are explosive. Never fuel
the machine indoors or
while the engine is hot
or running. Extinguish
cigarettes, cigars, pipes
and other sources of
ignition.
Now that you have setup your lawn mower, its important to become acquainted with its controls and features.
Blade Control
Gas and Oil Fill-Up
Refer to the engine manual for instructions.
The blade control is attached to the upper handle of
the mower. Depress and squeeze it against the upper
handle to operate the unit. Release it to stop engine and
1. Check oil level and add oil if necessary. Follow engine
manual for this.
blade.
2. Service the engine with gasoline as instructed in the
engine manual. Refer to the engine manual for the
location of the gas and oil fill.
WARNING: This blade control is a safety
device. Never attempt to bypass its opera-
tions.
Keep hands and feet
away from the chute area
on cutting deck. Refer to
warning label on the unit.
WARNING: Use extreme care when handling
gasoline. Gasoline is extremely flammable
and the vapors are explosive. Never fuel the
machine indoors or while the engine is hot or run-
ning. Extinguish cigarettes, cigars, pipes and other
sources of ignition.
Cutting Height Adjustment Levers
One adjustment lever is located at each wheel and is
used to adjust the cutting height. All four wheels must
be positioned at the same height to ensure a uniform
cut.
Recoil Starter
The recoil starter is attached to the right upper handle.
Stand behind the unit and pull the recoil starter rope to
start the unit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Starting Engine
WARNING: Be sure no one other than the
operator is standing near the lawn mower
while starting engine or operating mower. Never
run engine indoors or in enclosed, poorly ventilated
areas. Engine exhaust contains carbon monoxide, an
odorless and deadly gas. Keep hands, feet, hair and
loose clothing away from any moving parts on engine
and lawn mower.
2
4
Operating
Your Lawn
Mower
Follow the set of instructions pertaining to your unit.
Refer to engine manual for help with the engine.
3
Briggs & Stratton/ Tecumseh Engine:
1. Push primer three times. Wait about two seconds
between each push. See Figure 4-2. In temperature
around 55° F or below, prime five times. Do not prime
to restart a warm engine.
3
1
2. Standing behind the mower, squeeze the blade control
against upper handle.
Figure 4-2: Starting the Briggs & Stratton/ Tecumseh engine.
3. Holding these two handles together firmly, grasp recoil
starter handle and pull rope out with a rapid, continu-
ous, full arm stroke. See Figure 4-2. Keeping a firm
grip on the starter handle, let the rope rewind slowly.
Repeat until engine cranks. Let the rope rewind each
time slowly.
3
WARNING
The operation of any lawn
mower can result in foreign
objects being thrown into
the eyes, which can damage
your eyes severely. Always
wear safety glasses while
operating the mower or
Honda Engine:
1. Place the fuel valve lever found on the left side of the
engine into the ON (OPEN) position. See Figure 4-3.
2. Move the choke lever all the way backward into the
choke position.
4
1
2
while performing any
adjustments or repairs on it.
3. Standing behind the mower, squeeze the blade control
against upper handle. The choke will now begin to
slowly return to the off choke position after activating
the blade control. Therefore, quickly move onto step
four below.
OFF
ON
Be sure no one other than
the operator is standing
near the lawn mower while
starting engine or operating
mower. Never run engine
indoors or in enclosed,
poorly ventilated areas.
Engine exhaust contains
carbon monoxide, an
odorless and deadly gas.
Keep hands, feet, hair and
loose clothing away from
any moving parts on engine
and lawn mower.
4. Holding these two handles together firmly, grasp recoil Figure 4-3: Starting the Honda engine.
starter handle and pull rope out with a rapid, continu-
ous, full arm stroke. See Figure 4-3. Keeping a firm
WARNING: If you strike a foreign object,
stop the engine. Remove wire from the
grip on the starter handle let the rope rewind slowly.
Repeat until engine cranks. Let the rope rewind each
time slowly.
spark plug, thoroughly inspect mower for
any damage, and repair damage before restarting
and operating. Extensive vibration of mower during
operation is an indication of damage. The unit
should be promptly inspected and repaired.
WARNING: Wait for the blade to stop com-
pletely before performing any work on the
mower or to remove the grass catcher.
Stopping Engine
1. Release blade control to stop the engine and blade.
Using as Mulcher
For mulching grass, remove the grass catcher and side
discharge chute from the mower. For effective mulching,
do not cut wet grass. If the grass has been allowed to
grow in excess of four inches, mulching is not recom-
mended. Use the grass catcher to bag clippings instead.
2. Disconnect spark plug wire from spark plug and
ground against the engine.
Never operate your mower
without either the rear door
or the entire grass catcher
assembly firmly secured.
UsingYour Lawn Mower
Be sure lawn is clear of stones, sticks, wire, or other
objects which could damage lawn mower or engine.
Such objects could be accidently thrown by the mower
in any direction and cause serious personal injury to the
operator and others.
Using Grass Catcher
You can use the grass catcher to collect clippings while
you are operating the mower. Refer to setup section for
instructions on attaching the grass catcher.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Lubrication
•
Lubricate pivot points on the blade control at least
once a season with light oil. The blade control must
operate freely in both directions. See Figure 5-1.
ꢀ
•
Lubricate the wheels at least once a season with
light oil (or motor oil). If wheels are removed for any
reason, lubricate surface of the pivot arm and inner
surface of the wheel with light oil. See Figure 5-1.
Maintaining
Your Lawn
Mower
•
•
Lubricate the torsion spring and pivot point on the rear
discharge door periodically with light oil to prevent
rust. See Figure 5-1.
Follow the accompanying engine manual for engine
lubrication schedule and instructions.
Deck Care
WARNING: Never tip the mower more than
90º in any direction and do not leave the
mower tipped for any length of time. Oil can drain
into the upper part of the engine causing a starting
problem.
Figure 5-1: Areas to lubricate on the mower.
WARNING
General Recommendations
•
Always observe safety rules when performing
any type of maintenance.
Clean underside of the mower deck after each use to
prevent build-up of grass clippings or other debris.
1. Disconnect spark plug wire. Drain gasoline from lawn
mower, or place a piece of plastic under the gas cap.
Always stop engine,
disconnect spark
plug, and ground
against engine before
performing and type
of maintenance on
the mower.
•
The warranty on this lawn mower does not cover
items that have been subjected to operator abuse
or negligence. To receive full value from warranty,
operator must maintain the lawn mower as
instructed here.
2. Tip mower so that it rests on the housing. Keep the
side with the air cleaner facing up. Hold mower firmly.
3. Scrape and clean the underside of the deck with a
suitable tool. Do not spray with water.
•
•
•
Changing of engine-governed speed will void
engine warranty.
4. Put the mower back on its wheels on the ground. If
you had put plastic under the gas cap earlier, make
sure to remove it now.
All adjustments should be checked at least once
each season.
Periodically check all fasteners and make sure these
are tight.
Engine Care
A list of key engine maintenance jobs required for good
performance by the mower is given below. Follow the
accompanying engine manual for a detailed list and
instructions.
WARNING: Always stop engine, disconnect
spark plug, and ground against engine
before cleaning, lubricating, or performing any type
of maintenance.
•
Maintain oil level as instructed in engine manual.
•
Service air cleaner every 25 hours under normal
conditions. Clean every few hours under extremely
dusty conditions. Poor engine performance and
flooding usually indicates that the air cleaner should
be serviced. To service the air cleaner, refer to the
engine manual.
IMPORTANT: Do not use a
pressure washer or garden
hose to clean your unit.
These may cause damage
to electric components,
spindles, pulleys, bear-
ings, or the engine. The
use of water will result in
shortened life and reduce
serviceability.
•
•
Clean spark plug and reset the gap once a season.
Spark plug replacement is recommended at the start
of each mowing season. Check engine manual for
correct plug type and gap specifications.
Clean engine regularly with a cloth or brush. Keep the
cooling system (blower housing area) clean to permit
proper air circulation. Remove all grass, dirt and
combustible debris from muffler area.
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Blade Care
WARNING: When removing the cutting blade
for sharpening or replacement, protect your
hands with a pair of heavy gloves or use a heavy rag
to hold the blade.
ꢀ
Blade
Blade
Adapter
Maintaining
Your Lawn
Mower
Periodically inspect the blade adapter for cracks,
especially if you strike a foreign object. Replace when
necessary. Follow the steps below for blade service.
1. Disconnect spark plug wire from spark plug. Turn
mower on its side making sure that the air filter and
the carburetor are up.
Bell Blade
Support
Hex Bolt
Figure 5-2: Remove blade and hardware.
2. Remove the bolt and the bell blade support which
hold the blade and the blade adapter to the engine
crankshaft. See Figure 5-2.
3. Remove blade and adapter from the crankshaft.
4. The blade can be sharpened with a file or on a grind-
ing wheel. Do not attempt to sharpen the blade while
it is still on the mower. When sharpening the blade,
follow the original angle of grind and grind each cut-
ting edge equally to keep the blade balanced. Balance
the blade on a round shaft screwdriver. Remove metal
from the heavy side until it balances evenly.
WARNING
When removing
the cutting blade
for sharpening or
replacement, protect
your hands with a
pair of heavy gloves
or use a heavy rag to
hold the blade.
WARNING: An unbalanced blade will cause
excessive vibration when rotating at high
speeds. It may cause damage to mower, and could
break causing personal injury.
5. Lubricate the engine crankshaft and slide the blade
adapter onto the engine crankshaft.
Figure 5-3: Cut wire rod to remove the rear flap.
6. Place the blade on the adapter such that the side
of the blade marked “Bottom” (or with part number)
faces the ground when the mower is in the operating
position. Make sure that the blade is aligned and
seated on the blade adapter flanges.
An unbalanced blade
will cause excessive
vibration when rotat-
ing at high speeds. It
may cause damage
to mower, and could
break causing per-
sonal injury.
Off-Season Storage
The following steps should be taken to prepare your
lawn mower for storage.
•
•
•
•
•
Clean and lubricate mower thoroughly as described
in the lubrication instructions.
7. Place blade bell support on the blade. Align notches
on the blade bell support with small holes in blade.
We do not recommend the use of a pressure washer
or garden hose to clean your unit.
8. Replace hex bolt and tighten hex bolt to torque: 450
in. lbs. min., 600 in. lbs. max.
Refer to engine manual for correct engine
storage instructions.
To ensure safe operation of your mower, periodically
check the blade bolt for correct torque.
Coat mower’s cutting blade with chassis grease to
prevent rusting.
Replacing Rear Flap
1. To remove rear flap, cut off the flat end of the wire rod
which secures it to the deck. See Figure 5-3.
Store mower in a dry, clean area. Do not store next
to corrosive materials, such as fertilizer.
2. Attach the new flap and new rod to deck, bending the
ends of the new rod over to secure to deck.
When storing any type of power equipment in a poorly
ventilated or metal storage shed, care should be taken
to rust-proof the equipment. Using a light oil or silicone,
coat the equipment, especially cables and all moving
parts of your lawn mower before storage.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
Remedy
Cause
1. Blade control disengaged.
2. Spark plug wire disconnected.
3. Fuel tank empty or stale fuel.
4. Engine not choked.
Problem
Engine fails to start
1. Engage blade control.
6
2. Connect wire to spark plug.
3. Fill tank with clean, fresh gasoline.
4. Choke engine as instructed in the
“Operating Your Lawn Mower” section.
5. Clean, adjust gap, or replace.
6. Clean fuel line.
Trouble
5. Faulty spark plug.
6. Blocked fuel line.
7. Engine flooded.
Shooting
7. Wait a few minutes to restart, but do
not prime.
1. Spark plug wire loose.
1. Connect and tighten spark plug wire.
2. Clean fuel line; fill tank with clean,
fresh gasoline.
Engine runs erratic
2. Blocked fuel line or stale fuel.
3. Vent in gas cap plugged.
4. Water or dirt in fuel system.
5. Dirty air cleaner.
3. Clear vent.
4. Drain fuel tank. Refill with fresh fuel.
5. Refer to engine manual.
6. Refer to engine manual.
6. Carburetor out of adjustment.
1. Engine oil level low.
1. Fill crankcase with proper oil.
2. Remove blower housing and clean.
3. Refer to engine manual.
Engine overheats
2. Air flow restricted.
For repairs beyond
the minor adjustments
listed here, contact
an authorized service
dealer.
3. Carburetor not adjusted properly.
1. Spark plug gap too close.
2. Carburetor idle mixture adjustment
improperly set.
1. Adjust gap to .030-inch.
2. Refer to engine manual.
Occasional skips
(hesitates) at high speed
1. Spark plug fouled, faulty or gap too wide.
1. Reset gap to .030-inch or replace
spark plug.
Idles poorly
2. Refer to engine manual.
3. Refer to engine manual.
2. Carburetor improperly adjusted.
3. Dirty air cleaner.
1. Cutting blade loose or unbalanced.
1. Tighten blade and adapter. Balance
blade.
Excessive Vibration
2. See an authorized service dealer.
2. Bent cutting blade.
1. Wet grass.
1. Do not mow when grass is wet; wait
until later to cut.
Mower will not mulch grass
2. Mow once at a high cutting height,
then mow again at desired height or
make a narrower cutting path.
3. Sharpen or replace blade.
2. Excessively high grass.
3. Dull blade.
1. Wheels not positioned correctly.
2. Dull blade.
1. Place all four wheels in same
height position.
Uneven cut
2. Sharpen or replace blade.
NOTE: Specifications are
subject to change without
notification or obligation.
Images my not reflect your
exact model and are for
reference purposes only.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Safety Label Found OnYour Lawn Mower
7
Safety
Labels
TO REDUCE THE RISK OF INJURY, DO NOT
OPERATE UNLESS DISCHARGE COVER OR
GRASS CATCHER IS IN ITS PROPER PLACE.
IF DAMAGED, REPLACE IMMEDIATELY.
MAX 15
˚
KEEP HANDS and FEET AWAY
• DO NOT MOW WHEN CHILDREN OR OTHERS
ARE AROUND.
AVOID SERIOUS INJURY OR DEATH
• KEEP HANDS AND FEET AWAY FROM
ROTATING PARTS.
• USE EXTRA CAUTION ON SLOPES. DO NOT
MOW SLOPES GREATER THAN 15 MOW
˚
ACROSS, NEVER UP AND DOWN. NEVER
PULL MOWER CLOSE TO YOUR FEET. LOOK
DOWN AND BEHIND BEFORE AND WHILE
MOVING BACKWARDS.
• REMOVE OBJECTS THAT CAN BE THROWN
BY THE BLADE IN ANY DIRECTION.
WEAR SAFETY GLASSES.
WARNING
READ OPERATOR'S MANUAL KEEP SAFETY DEVICES (BLADE CONTROL, TRAILING SHIELD,
DISCHARGE COVER, ETC) IN PLACE AND WORKING. IF DAMAGED, REPLACE IMMEDIATELY.
S32102 CD
DO NOT remove safety
(or any) labels from
mower for any reason.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Model Series 410 & 420
1
9
12
2
11
4
3
10
6
5
13
14
15
7
8
17
19
20
18
22
21
38
16
41
40
35
23
29
35
34
39
24
36
29
37
33
30
31
33
29
25
29
27
28
26
32
Wheel Treads
Pin Bar Tread
Zag Tread
S-WaveTread
K2 Tread
14
Download from Www.Somanuals.com. All Manuals Search And Download.
1
2
3
4
5
6
7
8
9
747-1161A
Blade Control
687-02074A Ht. Adj. Assy. Front - RH (8” Wheel)
687-02099A Ht. Adj. Assy. Front - LH (7” Wheel)
687-02100A Ht. Adj. Assy. Front - RH (7” Wheel)
24 782-5002B Front Baffle
749-1092A Upper Handle
710-1205
720-0279
710-1174
Rope Guide
8
Wing Nut, 1/4-20
Carriage Bolt, 5/16-18 x 2
25 748-0377C Blade Adapter
720-04072 Hand Star Knob
749-0928A Lower Handle
26 742-0641
742-0741†
Standard Blade
Mulch Blade
Parts List
712-0397
746-0957
746-1130
746-0554
746-1137
Wing Nut, 1/4-20
Control Cable - 37.25”
Control Cable - 40”
Control Cable - 40.5”
Control Cable - 53”
Cable Tie
27 736-0524B Blade Bell Support
28 710-1257 Screw, 3/8-24 x 2.50
29 712-04065 Flange Lock Nut, 3/8-16
30 787-01290 Height Adjustment Plate
31 687-02076A Pivot Arm Assy RH (7" wheel)
687-02077A Pivot Arm Assy LH (7" wheel)
687-02076A Pivot Arm Assy LH (8" wheel)
687-02077A Pivot Arm Assy RH (8" wheel)
10 726-0240
11 664-04007A Grass Bag Assembly
12 747-04080 Grass Bag Frame
13 732-0700
Trailshield Wire
32
‡
Front Wheel
To order replacement
parts, contact
14 731-05642 Trailshield
33 738-0507B Shoulder Screw
15 747-04587 Rear Door Pivot Rod
16 710-0654A TT Screw, 3/8-16 x 1
17 731-05865 Rear Discharge Door
18 731-04150C Rear Baffle
34 732-0404
35 720-0426
Spring Lever
1-800-800-7310
or visit
Height Adjustment Knob
36 687-02071A Pivot Arm Assembly - RH
687-02070A Pivot Arm Assembly - LH
37 732-04175 Spring Lever
19 732-04090A Torsion Spring RH
20 710-1241
Screw, 1/4-15 x 1.00
38 710-0703
39
Carriage Bolt, 1/4-20
Rear Wheel
21 787-01276 Deck 21 inch
‡
22 687-02271 Handle Bracket Assy - RH
687-02270 Handle Bracket Assy - LH
23 687-02075A Ht. Adj. Assy. Front - LH (8” Wheel)
40 710-1652
41 714-0104
Screw, 1/4-20 x .625
Hairpin Clip
† If equipped
‡ Refer to Wheel Chart
‡ Wheel Chart
Part No.
Type
Tread
Bar
Wheels w/o bearing
734-1781, Slot Hub
734-04215, 8 x 1.8
734-04213, 7 x 1.8
734-2004A, Disc Hub
734-2005A
K2 Bar
K2 Bar
Zag
Wheels w/ BB
Zag
This Operator’s Manual covers a range of product specifications for various models. Characteristics and features
discussed and/or illustrated in this manual may not be applicable to all models. MTD LLC reserves the right to
change product specifications, designs, and equipment without notice and without incurring obligation.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR
The limited warranty set forth below is given by MTD LLC with respect
to new merchandise purchased and used in the United States, its
possessions and territories.
e. MTD does not extend any warranty for products sold or exported
outside of the United States, its possessions and territories, except
those sold through MTD’s authorized channels of export distribution.
“MTD” warrants this product against defects in material and workman-
ship for a period of two (2) years commencing on the date of original
purchase and will, at its option, repair or replace, free of charge, any
part found to be defective in materials or workmanship. This limited war-
ranty shall only apply if this product has been operated and maintained
in accordance with the Operator’s Manual furnished with the product,
and has not been subject to misuse, abuse, commercial use, neglect,
accident, improper maintenance, alteration, vandalism, theft, fire, water,
or damage because of other peril or natural disaster. Damage resulting
from the installation or use of any part, accessory or attachment not
approved by MTD for use with the product(s) covered by this manual
will void your warranty as to any resulting damage.
Normal wear parts are warranted to be free from defects in material and
workmanship for a period of thirty (30) days from the date of purchase.
Normal wear parts include, but are not limited to items such as: batter-
ies, belts, blades, blade adapters, grass bags, rider deck wheels, seats,
snow thrower skid shoes, shave plates, auger spiral rubber and tires.
HOW TO OBTAIN SERVICE: Warranty service is available, WITH
PROOF OF PURCHASE, through your local authorized service
dealer. To locate the dealer in your area, check your Yellow Pages,
or contact MTD LLC at P.O. Box 361131, Cleveland, Ohio 44136-
0019, or call 1-800-800-7310 or 1-330-220-4683 or log on to our
f. Replacement parts that are not genuine MTD parts.
g. Transportation charges and service calls.
No implied warranty, including any implied warranty of mer-
chantability of fitness for a particular purpose, applies after the
applicable period of express written warranty above as to the
parts as identified. No other express warranty, whether written or
oral, except as mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product, shall
bind MTD. During the period of the warranty, the exclusive remedy
is repair or replacement of the product as set forth above.
The provisions as set forth in this warranty provide the sole and
exclusive remedy arising from the sale. MTD shall not be liable
for incidental or consequential loss or damage including, without
limitation, expenses incurred for substitute or replacement lawn
care services or for rental expenses to temporarily replace a
warranted product.
Some states do not allow the exclusion or limitation of incidental or
consequential damages, or limitations on how long an implied warranty
lasts, so the above exclusions or limitations may not apply to you.
In no event shall recovery of any kind be greater than the amount of the
purchase price of the product sold. Alteration of safety features of
the product shall void this warranty. You assume the risk and liability
for loss, damage, or injury to you and your property and/or to others and
their property arising out of the misuse or inability to use the product.
This limited warranty shall not extend to anyone other than the original
purchaser or to the person for whom it was purchased as a gift.
HOW STATE LAW RELATES TO THIS WARRANTY: This limited
warranty gives you specific legal rights, and you may also have other
rights which vary from state to state.
This limited warranty does not provide coverage in the following cases:
a. The engine or component parts thereof. These items may carry a
separate manufacturer’s warranty. Refer to applicable manufacturer’s
warranty for terms and conditions.
b. Log splitter pumps, valves, and cylinders have a separate one year
warranty.
c. Routine maintenance items such as lubricants, filters, blade
sharpening, tune-ups, brake adjustments, clutch adjustments, deck
adjustments, and normal deterioration of the exterior finish due to
use or exposure.
IMPORTANT: Owner must present Original Proof of Purchase to obtain
warranty coverage.
d. Service completed by someone other than an authorized service
dealer.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-ꢁ310, 1-330-220-4683
Download from Www.Somanuals.com. All Manuals Search And Download.
|