Operator’s Manual
Edger
Models 520
550
551
554
Model 550 and 551 Shown
IMPORTANT: READ SAFETY RULES AND INSTRUCTIONS CAREFULLY
Warning: This unit is equipped with an internal combustion engine and should not be used on or near any unimproved forest-
covered, brush-covered or grass-covered land unless the engine’s exhaust system is equipped with a spark arrester meeting
applicable local or state laws (if any). If a spark arrester is used, it should be maintained in effective working order by the operator.
In the State of California the above is required by law (Section 4442 of the California Public Resources Code). Other states may have
similar laws. Federal laws apply on federal lands. A spark arrester for the muffler is available through your nearest engine authorized
service dealer or contact the service department, P.O. Box 361131 Cleveland, Ohio 44136-0019.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019
PRINTED IN U.S.A.
769-00527E
FORM NO.
(3/04)
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 1: IMPORTANT SAFE OPERATION PRACTICES
WARNING: THIS SYMBOL POINTS OUT IMPORTANT SAFETY INSTRUCTIONS WHICH, IF NOT
FOLLOWED, COULD ENDANGER THE PERSONAL SAFETY AND/OR PROPERTY OF YOURSELF
AND OTHERS. READ AND FOLLOW ALL INSTRUCTIONS IN THIS MANUAL BEFORE ATTEMPTING
TO OPERATE THIS MACHINE. FAILURE TO COMPLY WITH THESE INSTRUCTIONS MAY RESULT
IN PERSONAL INJURY. WHEN YOU SEE THIS SYMBOL — HEED ITS WARNING.
WARNING: The Engine Exhaust from this product contains chemicals known to the
State of California to cause cancer, birth defects or other reproductive harm.
DANGER: This machine was built to be operated according to the rules for safe operation in this manual. As with
any type of power equipment, carelessness or error on the part of the operator can result in serious injury.
If you violate any of these rules, you may cause serious injury to yourself or others.
4. Never attempt to make any adjustments while the
TRAINING
engine is running, except where specifically
1. Read, understand, and follow all instructions on the
recommended in the operator’s manual.
machine and in the manual(s) before attempting to
5. To avoid personal injury or property damage use
assemble and operate. Keep this manual in a safe
extreme care in handling gasoline. Gasoline is
place for future and regular reference and for
ordering replacement parts.
2. Be familiar with all controls and their proper
operation. Know how to stop the machine and
disengage them quickly.
3. Never allow children under 14 years old to operate
extremely flammable and the vapors are explosive.
Serious personal injury can occur when gasoline is
spilled on yourself or your clothes which can ignite.
Washer your skin and change clothes immediately.
a. Use only an approved gasoline container.
b. Extinguish all cigarettes, cigars, pipes and
this machine. Children 14 years old and over
other sources of ignition.
should read and understand the operation
c. Never fuel machine indoors.
instructions and safety rules in this manual and
d. Never remove gas cap or add fuel while the
should be trained and supervised by a parent.
engine is hot or running.
4. Never allow adults to operate this machine without
e. Allow engine to cool at least two minutes
proper instruction.
before refueling.
5. To help avoid blade contact or a thrown object
f. Never over fill fuel tank. Fill tank to no more
injury, keep bystanders, helpers, children and pets
than ½ inch below bottom of filler neck to
at least 75 feet from the machine while it is in
provide space for fuel expansion.
operation. Stop machine if anyone enters the area.
g. Replace gasoline cap and tighten securely.
h. If gasoline is spilled, wipe it off the engine
PREPARATION
and equipment. Move unit to another area.
Wait five minutes before starting the engine.
i. Never store the machine or fuel container
inside where there is an open flame, spark or
pilot light as on a water heater, space heater,
furnace,clothes dryer or other gas
appliances.
1. Thoroughly inspect the area where the equipment
is to be used. Remove all stones, sticks, wire,
bones, toys and other foreign objects which could
be tripped over or picked up and thrown by the
blade. Thrown objects can cause serious personal
injury.
j. Allow machine to cool at least 5 minutes
before storing.
2. Always wear safety glasses or safety goggles
during operation and while performing an
adjustment or repair to protect your eyes. Thrown
objects which ricochet can cause serious injury to
the eyes.
3. Wear sturdy, rough-soled work shoes and close-
fitting slacks and shirts. Shirts and pants that cover
the arms and legs and steel-toed shoes are
recommended. Never operate this machine in bare
feet, sandals, slippery or light weight (e.g. canvas)
shoes.
OPERATION
1. Do not put hands or feet near rotating parts.
Contact with the rotating blade can amputate hands
and feet.
2. The blade control handle is a safety device. Never
bypass its operation. Doing so, makes the machine
unsafe and may cause personal injury.
3. Never operate without blade guard, debris shield
and blade control handle in place and working.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Never operate with damaged safety devices.
Failure to do so, can result in personal injury.
5. Never run an engine indoors or in a poorly
ventilated area. Engine exhaust contains carbon
monoxide, an odorless and deadly gas.
6. Do not operate machine while under the influence
of alcohol or drugs.
18. Only use parts and accessories made for this
machine by the manufacturer. Failure to do so, can
result in personal injury.
19. If situations occur which are not covered in this
manual, use care and good judgment. Contact an
authorized MTD service dealer or telephone 1-800-
800-7310.
7. Muffler and engine become hot and can cause a
burn. Do not touch.
MAINTENANCE AND STORAGE
8. Never operate this machine without good visibility
or light. Always be sure of your footing and keep a
firm hold on the handles. Walk, never run.
9. Do not operate this machine if it has been dropped
or damaged. Return machine to your nearest
authorized servicing dealer for examination and
repair.
1. Never tamper with safety devices. Check their
proper operation regularly.
2. Before cleaning, repairing, or inspecting,
disconnect the spark plug wire and ground against
the engine to prevent unintended starting.
3. Check bolts, and screws for proper tightness at
frequent intervals to keep the machine in safe
working condition. Also, visually inspect machine
for any damage.
4. Do not change the engine governor setting or over-
speed the engine. The governor controls the
maximum safe operating speed of the engine.
5. The blade, blade guard and debris shield are
subject to wear and damage. For your safety
protection, frequently check all components and
replace with original equipment manufacturer’s
(O.E.M.) parts only. “Use of parts which do not
meet the original equipment specifications may
lead to improper performance and compromise
safety!”
10. Do not operate this machine with a damaged or
excessively worn cutting blade.
11. Never attempt to clear material from the blade
guard while the engine is running. Shut the engine
off, disconnect the spark plug wire and ground
against the engine to prevent unintended starting.
12. Do not overload machine capacity by attempting to
edge at too fast of a rate.
13. Stay alert for uneven sidewalks, terrain etc. Always
push slowly over rough surfaces. Do not use this
machine on gravel surfaces.
14. Do not operate machine in rain or wet soil
conditions.
15. Always operate machine from behind the handles
and position yourself where the direct line of sight
to cutting blade is blocked by guards.
16. Always stop engine when edging or trimming is
delayed or when transporting machine from one
location to another.
17. Never leave a running machine unattended. Stop
the engine, disconnect spark plug wire and ground
against the engine to prevent unintended starting.
6. Maintain or replace safety and instruction labels, as
necessary.
7. Observe proper disposal laws and regulations for
gas, oil, etc. to protect the environment.
8. Never store the machine or fuel container inside
where there is an open flame, spark or pilot light
such as a water heater, furnace,clothes dryer etc.
9. Always refer to the operator’s manual for proper
instructions on off-season storage.
WARNING: YOUR RESPONSIBILITY
Restrict the use of this power machine to persons who read, understand and follow the warnings
and instructions in this manual and on the machine.
KEEP AWAY — ROTATING BLADE
Figure 1
4
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 2: ASSEMBLING YOUR EDGER
IMPORTANT: This unit is shipped WITHOUT
GASOLINE or OIL. After setting up the unit, service
engine with gasoline and oil as instructed in the
separate engine manual packed with your unit.
Upper Handle
NOTE: Reference to right or left hand side of the edger
is observed from the operating position.
Positioning the Edger Handles
Blade Control Bail
•
•
•
Remove and discard any packaging cardboard that
may be present between the upper handle and the
lower handle.
Depress the blade control bail at the top of the
upper handle and pivot the upper handle upward
until it snaps into place.
Rope Guide
Tighten the wing knobs which are located on both
the left and right sides of the handle. See Figure 2 .
Wing Knob
Figure 3
Wing Knobs
Upper Handle
•
Stand behind the unit and hold the blade control
bail against the upper handle and gently pull the
starter rope out of the engine.
WARNING: The edger blade WILL rotate
when the starter rope is pulled.
NOTE: The starter rope will not pull out of the engine
unless the blade control bail (refer to Figure 3) is
depressed against the upper handle.
Lower Handle
•
•
Slip the starter rope through the top of the rope
guide.
Retighten the wing knob which secures the rope
guide to the upper handle.
Figure 2
Attaching the Starter Rope
•
Locate the eyebolt found on the right side of the
upper handle.
•
Loosen, but do NOT remove, the wing knob which
secures the rope guide to the upper handle. See
Figure 3.
5
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 3: KNOW YOUR EDGER
Blade Control Bail
Blade Depth
Control Lever
(Transport Position Shown)
Pull Rope / Recoil Starter
Curb Height
Adjustment Lever
(If Equipped)
Bevel Adjustment
Lever
(If Equipped)
Primer
Spindle Sheaves Belt Guard
NOTE: Wheel and blade styles vary by model. Yours may differ slightly.
Model 550 and 551 Shown.
Figure 4
WARNING: Be familiar with all controls
Blade Depth Control Lever
and their proper operation. Know how to
stop the machine and disengage them
quickly.
The blade depth control lever is located on the right
side of the upper handle. It is used to control the depth
of the cut. The further forward the blade depth control
lever is moved, the deeper into the soil the edger blade
will cut. See Figure 4.
NOTE: Refer to the Engine Manual packed with your
edger for a detailed description of all engine-related
controls and components.
Bevel Adjustment Lever (if so equipped)
Pull Rope / Recoil Starter
The bevel adjustment lever, if so equipped, is located
on the front, left portion of the edger, behind the edger
blade. It is used to vary the angle of the edger blade
between one of three positions for edging/trenching or
beveled edging. See Figure 4.
The pull rope/recoil starter is used to start the engine.
Primer
The primer is used to pump gas into the carburetor and
aid in starting the engine. Use it to start a cold engine,
but do not use it to restart a warm engine after a short
shutdown.
Curb Height Adjustment Lever
(if so equipped)
NOTE: Refer to the Engine Manual packed with your
edger for a detailed description of all engine-related
controls and components.
The curb height adjustment lever, if so equipped, is
found on the rear portion of the edger.When placed in
an applicable notch, it aids in stabilizing the edger while
edging grass along a curb. See Figure 4.
Blade Control Bail
IMPORTANT: Become familiar with all the controls
before operating the edger.
Located on the upper handle, the blade control bail
must be depressed against the upper handle in order to
operate the unit. Releasing the blade control stops the
engine and the edger blade. See Figure 4.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 4: OPERATING YOUR EDGER
The operation of any edger can result
•
•
After slowly allowing the rope to recoil, pull the rope
with a rapid, continuous, full arm stroke. Keep a firm
grip on starter handle throughout the entire stroke.
Allow the starter handle to slowly return to the
eyebolt.
WEAR YOUR
SAFETY GLASSES
in foreign objects being thrown into
the eyes, which can result in severe
eye damage. Always wear safety
FORESIGHT IS BETTER
THAN NO SIGHT
glasses or eye shields. We
recommend wide vision safety mask
for over spectacles or standard
safety glasses
NOTE: If the engine fails to start after three pulls,
depress the primer an additional two times before
pulling the starter rope again.
WARNING: Do not lower blade if blade is
over concrete, asphalt, rocks or the like. The
blade can strike the supporting surface,
resulting in personal injury or property
damage.
Edging
To begin edging, proceed as follows:
1. Move the unit over to the area to be edged, making
sure that the left rear wheel is on a hard surface
and the blade is over the area to be cut. See Figure
5.
Adding Gasoline And Oil
Service the engine with gasoline and oil as instructed in
the Engine Manual packed with your edger. Read
instructions carefully.
WARNING: Never fill fuel tank indoors, with
engine running or until the engine has been
allowed to cool for at least two minutes after
running.
Starting The Engine
NOTE: Refer to the Engine Manual packed with your
edger for a detailed description of all engine-related
controls and components.
To start the edger’s engine, proceed as follows:
•
Move the blade depth control lever back to the
START position in the adjacent (top) notch.
Depress the primer bulb three times, pausing two to
three seconds between each push. In cold weather
(below 50°F /19°C), it may be necessary to depress
the primer bulb four or five times.
Figure 5
2. Move the blade depth control lever to the left and
place it into any of the five lower notches. The
further forward the blade depth control lever is
moved, the deeper or lower the blade will cut into
the ground.
3. For best results, proceed slowly along the path
being edged, slowly moving the edger back and
forth through the cutting area, again making sure to
keep the left rear wheel on the hard surface and the
blade in the cutting path, close to but not touching
the edge of the hard surface.
•
IMPORTANT: Using the primer to restart a warm engine
after a short shutdown is usually not necessary. Doing
so may result in a flooded engine.
•
Standing behind the unit, depress the blade control
bail and hold it against the upper handle with your
left hand.
4. Once you have reached the end of your cutting
path, raise the blade control lever back into the
START position, move to the next area to be cut,
and proceed again from step 1.
WARNING: This control mechanism is a
safety device. Never attempt to bypass its
operation.
•
With your right hand, grasp the recoil starter handle
and slowly pull the rope outward until engine
reaches the start of its compression cycle (the rope
will pull slightly harder at this point).
Stopping The Engine
To stop the edger’s engine, release the blade control
handle.
NOTE: See your engine manual packed with your unit
for more detailed instructions.
7
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Pivot the right, rear wheel into an applicable
position in relation to the height of the curb to be
edged along.
Release the curb height adjustment lever to lock
the wheel in position. See Figure 7.
Edging Along A Curb (models so
equipped)
NOTE: Edger features vary by model. All edger models
do NOT come equipped to edge along a curb nor is
there a curb wheel kit available to modify your edger if it
was not purchased equipped to do so.
On models so equipped, the right, rear wheel of the
edger can be lowered into one of five positions to ease
the task of edging along a curb.
To adjust the height of the curb wheel, proceed as
follows:
•
Lower the right, rear wheel by moving the curb
height adjustment lever slightly to the left. See
Figure 6.
(Lowered Position)
Curb Height Adjustment Lever
Figure 7
•
Proceed to step 1 under Edging.
Curb Height
Adjustment
Lever
(Normal Operating
Position)
Figure 6
SECTION 5: MAKING ADJUSTMENTS
Bevel Adjustment (models so equipped)
NOTE: Edger features vary by model. All edger models
do NOT come equipped for blade tilt adjustment nor is
there a blade tilt kit available to modify your edger if it
was not purchased equipped to do so.
The angle of the edger blade can be adjusted by
placing the bevel adjustment lever in one of three
positions for edging/trenching or beveled edging. See
Figure 8.
Bevel
Adjustment
Lever
Beveling
Edging/Trenching
Position Shown
Figure 8
8
Download from Www.Somanuals.com. All Manuals Search And Download.
WARNING: Rotating cutting blade may
throw objects causing personal injury.
Keep area clear of bystanders and do not
operate without guards in place.
Flange Lock Nut
Beveling
In order to achieve a bevelled edge, set the bevel
adjustment lever (refer to Figure 8) in the first (left hand)
or third (right hand) notch to place the edger blade in
position for beveling. See Figure 9.
Engine
Flywheel Pulley
Spindle
Sheaves Belt Guard
Figure 10
•
Remove the spindle sheaves belt guard by
removing the two self-tapping screws which secure
it to the blade plate assembly. See Figure 11.
Blade Plate
Assembly
Beveling Positions
Figure 9
Trenching (models so equipped)
In order to create a wider cutting path for such things as
laying wire for landscape lighting or invisible fences,
you can utilize the edger’s trenching feature (if so
equipped).
Hex
Screws
Spindle Sheaves
Belt Guard
NOTE: Edger features vary by model. All edger models
do NOT come equipped for trenching. If your edger was
not purchased equipped to do so, you may purchase
part no. 736-04088 (flat washer) and part no. 781-0748
(triplex edger blade) to utilize this feature.
Spindle Sheaves
Note: Wheel and blade styles vary by model.
Figure 11
•
Use two wrenches (one wrench to prevent the hex
bolt head from spinning and the other to unthread
the hex lock nut) to remove the hex lock nut and
bell washer that secure the edger blade, leaving the
edger blade in place. See Figure 12.
WARNING: Disconnect the spark plug wire
and ground against the engine before
performing the following steps.
WARNING: The edger blade is sharp. Wear
leather work gloves to protect your hands
when working around the edger blade.
•
•
Working in front of the edger, loosen the flange lock
nut on top of frame, allowing the idler pulley
assembly to pivot slightly out from the frame. See
Figure 10.
With your other hand, carefully reach under the rear
of the unit and remove the belt from around the
engine flywheel pulley. See Figure 10.
Bell Washer
Hex Lock Nut
Note: Wheel styles vary by model.
Figure 12
Hex Bolt Head
9
Download from Www.Somanuals.com. All Manuals Search And Download.
•
•
Install the flat washer (part no. 736-04088) and the
triplex edger blade (part no. 781-0748) that are
packed separately in the box.
Secure with the bell washer and the hex lock nut
removed earlier. See Figure 13.
IMPORTANT: Make certain that the drive belt is seated
correctly on the blade spindle and that it is riding
smoothly on the spindle sheaves and is not pinched
between them. Repeat the first three steps if the belt is
pinched.
•
Set the bevel adjustment lever (refer to Figure 8) in
the center notch to place the edger blade in a 90°
position (see Figure 14) and place the blade depth
control lever in the lowest position.
Bell Washer
Edger Blade
Flat Washer
Triplex Blade
Hex Lock Nut
90°
Figure 13
IMPORTANT: Use a torque wrench to tighten the hex
lock nut to between 37 foot-lbs. and 50 foot-lbs.
Edging/Trenching Position
Figure 14
•
Reinstall the spindle belt guard with the self tapping
screws removed earlier.
IMPORTANT: For best results, proceed slowly along the
path being trenched, slowly moving the edger back and
forth through the cutting area.
•
Carefully place the drive belt back onto the engine
flywheel pulley, and retighten the flange lock nut on
the top of the frame.
SECTION 6: MAINTAINING & SERVICING YOUR EDGER
WARNING: Disconnect the spark plug wire
and ground against the engine before
performing any adjustment, repairs or
maintenance.
Bearing Block
On the Model 550 and551, the bearing block is
equipped with a grease fitting. Lubricate with a grease
gun after every 25 hours or at least once a season. On
the Model 521, simply apply oil through the tiny hole in
the cover plate. See Figure 15.
Lubrication
Engine
Refer to the Engine Manual packed with your edger for
a detailed description of all engine-related service
specifications.
Model 550 and 551
Shown
Wheels
Lubricate the wheels and bearings at least once a
season with a light oil. Also if the wheels are removed
for any reason, lubricate the surface of the axle bolt and
the inner surface of the wheel with light oil.
Pivot Points
Lubricate the pivot points on the blade control bail,
blade depth control lever, and if applicable, the blade
adjustment lever, and curb height adjustment lever with
light oil at least once a season.
Lube
Fitting
Figure 15
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Replacing the Edger Blade
Flange Lock Nut
WARNING: The edger blade is sharp. Wear
leather work gloves to protect your hands
when working around the edger blade.
Engine
Flywheel
Pulley
WARNING: Disconnect the spark plug wire
and ground against engine before
performing the following steps.
•
Working in front of the edger, loosen the flange lock
nut on top of frame, allowing the idler pulley
assembly to pivot slightly out from the frame. See
Figure 16.
Flat Side
of Belt
Spindle Sheaves
“V” Side
of Belt
Idler Pulley
Assembly
Belt Guard
•
•
•
With your other hand, carefully reach under the rear
of the unit and remove the belt from around the
engine flywheel pulley.
Remove the spindle sheaves belt guard by
removing the two self-tapping screws which secure
it to the blade plate assembly. See Figure 11.
Use two wrenches (one wrench to prevent the hex
bolt head from spinning and the other to remove the
hex lock nut and bell washer) to remove the edger
blade. Refer to Figure 12.
Remove and discard the edger blade but retain the
bell washer and hex lock nut.
Install the replacement edger blade, the bell
washer (cupped side facing inward) and the hex
lock nut removed earlier.
Figure 16
The edger drive belt is subject to wear and should be
replaced if any signs of cracking, shredding or rotting
are present. To replace the belt, proceed as follows:
•
Working in front of the edger, loosen the flange lock
nut on top of frame, allowing the idler pulley
assembly to pivot slightly out from the frame. See
Figure 16.
With your other hand, carefully reach under the rear
of the unit and remove the belt from around the
engine flywheel pulley.
Remove the spindle sheaves belt guard by
removing the two self-tapping screws which secure
it to the blade plate assembly. See Figure 11.
Carefully remove the belt from off of the pulleys,
again making sure to note the orientation of the
belt. Discard the belt.
•
•
•
•
•
IMPORTANT: Use a torque wrench to tighten the hex
lock nut to between 37 foot-lbs. and 50 foot-lbs.
•
Reinstall the spindle belt guard with the self tapping
screws removed earlier.
Carefully place the drive belt back onto the engine
flywheel pulley, and retighten the flange lock nut on
the top of the frame.
Install the replacement belt (Part No. 754-04032) in the
same configuration that the original belt was routed as
follows:
•
•
Working from the front of the edger, place the belt
onto the spindle sheaves, route it back onto the two
idler pulleys, and then place it onto the engine
flywheel pulley.
IMPORTANT: Make certain that the drive belt is seated
correctly on the blade spindle and that it is riding
smoothly on the spindle sheaves and is not pinched
between them. Repeat the first three steps if the belt is
pinched.
IMPORTANT:Make certain that the “V” side of the belt is
seated into the top pulley and the flat side of the belt is
seated into the bottom pulley. See Figure 16.
•
Reinstall the spindle sheaves belt guard with the
self tapping screws removed earlier.
Replacing the Drive Belt
IMPORTANT: To aid in reassembly, note the orientation
of the drive belt on the two idler pulleys and the engine
flywheel pulley prior to performing the following steps.
Refer to Figure 16.
•
Make certain that the drive belt is on the engine
flywheel pulley and idler pulleys, and retighten the
flange lock nut on the top of the frame.
IMPORTANT: Make certain that the drive belt is seated
correctly and that it is riding smoothly on the spindle
sheaves and is not pinched between them. Repeat the
first three steps if the belt is pinched.
WARNING: Never operate the edger without
the spindle sheaves belt guard in place.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 7: OFF-SEASON STORAGE
Observe the following when preparing the edger for
long-term storage:
•
•
Store the edger in a dry, clean area. Do not store
next to any corrosive materials, such as lawn
fertilizer.
Coat the edger, especially any springs and
bearings with a light oil or silicone spray.
•
Clean and lubricate unit thoroughly as instructed on
page 10 of this manual.
•
Refer to the Engine Manual packed separately with
the edger for engine manufacturers’s storage
instructions.
IMPORTANT: When storing any type of power
equipment in an poorly ventilated or metal storage
shed, care should be taken to rustproof the equipment.
•
Coat the edger blade with chassis grease to
prevent rusting and corrosion.
SECTION 8: TROUBLESHOOTING
Trouble
Engine fails to start Dirty air cleaner
Engine needs to be primed
Possible Cause(s)
Corrective Action
Refer to the Engine Manual packed with your unit.
Push primer bulb two or three times.
Fuel tank empty
Fill tank with clean, fresh gasoline.
Stale fuel in gasoline tank
Spark plug wire disconnected.
Spark plug fouled
Drain gasoline and refill tank with clean, fresh gasoline.
Connect the spark plug wire to the spark plug.
Clean, adjust gap or replace spark plug.
Engine flooded
Refer to the Engine Manual packed with your unit.
Engine runs erratic Spark plug wire loose
Connect and tighten spark plug wire.
Stale fuel in gasoline tank
Vent in gas cap plugged
Water or dirt in fuel system
Dirty air cleaner
Drain gasoline and refill tank with clean, fresh gasoline.
Clear vent of any debris.
Drain fuel tank. Refill with fresh fuel.
Refer to the Engine Manual packed with your unit.
Refer to the Engine Manual packed with your unit.
Carburetor out of adjustment
Engine overheats
Engine oil level low
Air flow restricted
Dirty air filter
Fill crankcase with proper oil.
Clean the area around the engine’s cooling fins.
Replace the engine’s air filter.
Carburetor not adjusted properly Refer to the Engine Manual packed with your unit.
Excessive vibration Edger blade bent or damaged Replace edger blade.
Blade spindle bent or damaged Contact an authorized MTD service dealer.
Belt worn or stretched Replace drive belt.
Drive belt slips
12
Download from Www.Somanuals.com. All Manuals Search And Download.
SECTION 9: PARTS LIST FOR MODEL 520/550/551/554 HANDLE
19†
15
8
20
14
11
18
6
5
1
17
7
13
10
3
16
12
2
9
11
6
4
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
REF.
NO.
12 746-04036
13 746-04035
746-04052
14 747-0976A
15 749-1225
16 749-4044
17 781-0741
18 781-0742
19 720-0297†
20 712-3027
PART
NO.
DESCRIPTION
DESCRIPTION
Wheel Adjustment Cable
Control Cable (Briggs & Stratton)
Control Cable (Tecumseh)
Bail Handle
Upper Handle
Lower Handle
Depth Index Bracket
Depth Index Lever
Foam Grip
710-3103
710-0449
710-1205
710-3008
710-0606
712-3004A
720-0279
720-0142
720-0241
Screw, 5/16-18
Screw, 5/16-18
Eye Bolt
Screw, 5/16-18
Screw
Hex Lock Nut, 5/16-18
Wing Nut
8
9
Grip
Wing Knob
10 732-0369
11 736-0451
Compression Spring
Saddle Washer,.320 ID x.93 OD
Hex Flange Nut, 1/4-20
†If so equipped
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 520/550/551/554 Frame
2
10
5
9
6
3
15
11
13
12
14
7
8
1
4
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
DESCRIPTION
Screw, 3/8-24
Screw, 1/4-20
Screw, 3/8-16
Screw, 3/8-16
Flange Lock Nut, 3/8-16
Debris Guard
710-0191
710-0599
710-0654A
710-0944
712-0431
731-04168
736-0320
736-0452
736-3052
Flat Washer, 3/8 ID x 1.37 OD
Bell Washer,.396 x 1.140
Flat Washer,.406 x 1.00
Flat Washer,.260 x.720
Pulley Mount Spacer
Flat Idler Pulley, 1.88 OD
Idler Pulley
8
9
10 736-3090
11 750-04142
12 756-0313
13 756-1035A
14 756-1150A
15 787-01072
Combination Flywheel Pulley
Frame
14
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 520 Spindle Assembly
28†
11
18
7
17
8
16
29†
10
19
25
21
17
20
9
1
3
27
15
7
17
24
22
2
26
23
4
13
5
12
14
6
V-BELTS are specially designed to engage and
disengage safely. A substitute (non-OEM) V-Belt
can be dangerous by not disengaging completely.
REF.
NO.
PART
NO.
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
DESCRIPTION
DESCRIPTION
Blade Plate Assembly
Hex Screw, 5/16-18
Self-tapping Screw, 1/4-20
Hex Screw, 5/8-18
Clevis Pin
Hex Lock Nut, 5/16-18
Hex Flange Nut, 1/4-20
Jam Nut, 5/8-18
Cotter Pin
Bearing Cup
Blade Guard
Bearing Block
Compression Spring
Lock Washer
16 736-0317
17 736-3090
18 738-04025
19 741-0524
20 736-04088
21 750-04105
22 750-0547
23 754-04032
24 756-0449
25 781-0080
26 781-0427
27 787-01075
Bell Washer,.63 ID x 1.2 OD
Flat Washer,.260 x.72
Pin, 1/4-20
Bearing,.625 ID x 1.57 OD
Flat Washer
Spacer,.63 x 1.12 x 1.06
Spacer,.632 ID x.875 OD
Belt
687-02019
710-0395
710-0599
710-1143A
711-1017
712-3004A
712-3027
712-3056
714-0104
8
9
Sheave
Blade
Belt Guard
Cover Plate
10 718-04012
11 731-04158
12 731-04207
13 732-04169
14 736-0119
15 736-0187
28 736-04088† Flat Washer
29 781-0748†
Tri Star Blade
Flat Washer
†If so equipped
15
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 550/551/554 Spindle Assembly
Model 554
Trencher Kit
30†
6
10
17
7
19
16
31†
9
20
27
23
17
22
1
18
3
29
8
15
6
26
2
24
28
21
25
4
12
13
11
14
5
V-BELTS are specially designed to engage and
disengage safely. A substitute (non-OEM) V-Belt
can be dangerous by not disengaging completely.
REF.
NO.
PART
NO.
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
DESCRIPTION
DESCRIPTION
Blade Plate Assembly
17 736-3090
18 737-3000
19 738-04025
20 741-0524
21 747-04110
22 736-04088
23 750-04105
24 750-0547
25 754-04032
26 756-0449
27 781-0080
781-0748
Flat Washer,.260 x.72
Lube Fitting, 3/16
Pin, 1/4-20
Bearing,.625 ID x 1.57 OD
Blade Adjustment Rod
Flat Washer,.635 x 1.2
Spacer,.63 x 1.12 x 1.06
Spacer,.632 ID x.875 OD
Belt
687-02019
710-0395
710-0599
710-1143A
712-3004A
712-3027
712-3056
714-3010
718-04012
Hex Screw, 5/16-18
Self-tapping Screw, 1/4-20
Hex Screw, 5/8-18
Hex Lock Nut, 5/16-18
Hex Flange Nut, 1/4-20
Jam Nut, 5/8-18
Cotter Pin
Bearing Cup
Blade Guard
Bearing Block
Compression Spring
Double Torsion Spring
Lock Washer
Flat Washer
Bell Washer,.63 ID x 1.2 OD
8
9
Sheave
10 731-04158
11 731-04207
12 732-04169
13 732-0188A
14 736-0119
15 736-0187
16 736-0317
Blade (Models 550 & 551)
Tri Star Blade (Model 554)
Spindle Belt Guard
Index Bracket
28 781-0427
29 787-01081
30 736-04088† Flat Washer
31 781-0748†
Tri Star Blade
†If so equipped
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 520 Wheel Assembly
3
1
8
(Frame shown for reference only)
6
8
9
10
3
1
1
1
8
2
7
5
4
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
DESCRIPTION
712-0431
732-04045
734-1987
734-1988
738-04037
738-04038
738-04039
750-0289
750-04129
Flange Lock Nut, 3/8-16
Torsion Spring
Wheel 8x1.8
Wheel 7x1.8
Shoulder Screw,.50 x 9.36, 3/8-16
Shoulder Screw,.50 x 12.90, 3/8-16
Shoulder Screw,.50 x 3.19, 3/8-16
Spacer,.510 ID x.875 OD
Spacer,.525 x.775
8
9
10 787-01074
Wheel Bracket
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 550 And 551 Wheel Assembly
2
8
17
(Frame shown for reference only)
4
2
7
4
18
2
15
8
19
5
2
10
1
9
8
11
6
3
14
12
13
16
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
DESCRIPTION
687-02022
712-0431
732-04045
734-1987
734-1988
736-0182
736-0208
736-0232
736-0234
Curb Height Adjustment Lever
Flange Lock Nut, 3/8-16
Torsion Spring
Wheel 8x1.8
Wheel 7x1.8
Spring Washer,.500 x 1.00
Flat Washer,.51 ID x 1.5 OD
Wave Washer,.531 ID x.781 OD
Washer,.385 x 1.5
8
9
10 738-0213
11 738-0380
12 738-04036
13 738-04037
14 738-04041
15 750-04129
16 750-04165
17 750-0664
18 781-0100
19 787-01074
Shoulder Screw,.498 x 1.445
Shoulder Screw,.50 x.27
Shoulder Screw,.50 x 4.62
Shoulder Screw,.50 x 9.36, 3/8-16
Shoulder Screw,.50 x 11.61
Spacer,.525 x.775
Spacer,.525 x.775
Spacer,.505 ID x.88 OD
Curb Height Adjuster Plate
Wheel Bracket
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Model 554 Wheel Assembly
5
2
8
17
(Frame shown for reference only)
2
7
8
17
5
2
18
16
10
4
2
15
17
9
1
19
6
11
3
14
8
12
13
REF.
NO.
1
2
3
4
5
6
7
PART
NO.
DESCRIPTION
687-02022
712-0431
732-04045
734-1264
734-1268
736-0182
736-0208
736-0232
736-0234
Curb Height Adjustment Lever
Flange Lock Nut, 3/8-16
Torsion Spring
Wheel 7 x 1.75
Wheel 8 x 1.75
Spring Washer,.500 x 1.00
Flat Washer,.51 ID x 1.5 OD
Wave Washer,.531 ID x.781 OD
Washer,.385 x 1.5
8
9
10 736-0326
11 738-0380
12 738-04036
13 738-04037
14 738-04041
15 738-0527
16 750-04129
17 750-0664
18 781-0100
19 787-01074
Flat Washer,.510 x 1.00
Shoulder Screw,.50 x.27
Shoulder Screw,.50 x 4.62
Shoulder Screw,.50 x 9.36, 3/8-16
Shoulder Screw,.50 x 11.61
Shoulder Screw,.498 x 2.045
Spacer,.525 x.688
Spacer,.505 ID x.88 OD
Curb Height Adjuster Plate
Wheel Bracket
19
Download from Www.Somanuals.com. All Manuals Search And Download.
MANUFACTURER’S LIMITED WARRANTY FOR:
The limited warranty set forth below is given by MTD LLC with
respect to new merchandise purchased and used in the
United States, its possessions and territories.
e.
MTD does not extend any warranty for products sold or
exported outside of the United States, its possessions
and territories, except those sold through MTD’s
authorized channels of export distribution.
Replacement parts that are not genuine MTD parts.
Transportation charges and service calls.
“MTD”warrants this product against defects in material and
workmanship for a period of two (2) years commencing on the
date of original purchase and will, at its option, repair or
replace, free of charge, any part found to be defective in
materials or workmanship. This limited warranty shall only
apply if this product has been operated and maintained in
accordance with the Operator’s Manual furnished with the
product, and has not been subject to misuse, abuse,
commercial use, neglect, accident, improper maintenance,
alteration, vandalism, theft, fire, water, or damage because of
other peril or natural disaster. Damage resulting from the
installation or use of any part, accessory or attachment not
approved by MTD for use with the product(s) covered by this
manual will void your warranty as to any resulting damage.
f.
g.
No implied warranty, including any implied warranty of
merchantability of fitness for a particular purpose,
applies after the applicable period of express written
warranty above as to the parts as identified. No other
express warranty, whether written or oral, except as
mentioned above, given by any person or entity,
including a dealer or retailer, with respect to any product,
shall bind MTD. During the period of the warranty, the
exclusive remedy is repair or replacement of the product
as set forth above.
The provisions as set forth in this warranty provide the
sole and exclusive remedy arising from the sale. MTD
shall not be liable for incidental or consequential loss or
damage including, without limitation, expenses incurred
for substitute or replacement lawn care services or for
rental expenses to temporarily replace a warranted
product.
Normal wear parts are warranted to be free from defects in
material and workmanship for a period of thirty (30) days from
the date of purchase. Normal wear parts include, but not
limited to items such as: batteries, belts, blades, blade
adapters, grass bags, rider deck wheels, seats, snow thrower
skid shoes, shave plates, auger spiral rubber and tires.
HOW TO OBTAIN SERVICE: Warranty service is available,
WITH PROOF OF PURCHASE, through your local authorized
service dealer. To locate the dealer in your area, check your
Yellow Pages, or contact MTD LLC at P.O. Box 361131,
Cleveland, Ohio 44136-0019, or call 1-800-800-7310 or 1-
330-220-4683 or log on to our Web site at
Some states do not allow the exclusion or limitation of
incidental or consequential damages, or limitations on how
long an implied warranty lasts, so the above exclusions or
limitations may not apply to you.
In no event shall recovery of any kind be greater than the
amount of the purchase price of the product sold. Alteration
of safety features of the product shall void this warranty.
You assume the risk and liability for loss, damage, or injury to
you and your property and/or to others and their property
arising out of the misuse or inability to use the product.
This limited warranty does not provide coverage in the
following cases:
a.
The engine or component parts thereof. These items
may carry a separate manufacturer’s warranty. Refer
to applicable manufacturer’s warranty for terms and
conditions.
This limited warranty shall not extend to anyone other than the
original purchaser or to the person for whom it was purchased
as a gift.
b.
c.
Log splitter pumps, valves, and cylinders have a
separate one year warranty.
HOW STATE LAW RELATES TO THIS WARRANTY: This
limited warranty gives you specific legal rights, and you may
also have other rights which vary from state to state.
Routine maintenance items such as lubricants, filters,
blade sharpening, tune-ups, brake adjustments, clutch
adjustments, deck adjustments, and normal
deterioration of the exterior finish due to use or
exposure.
IMPORTANT: Owner must present Original Proof of
Purchase to obtain warranty coverage.
d.
Service completed by someone other than an
authorized service dealer.
MTD LLC, P.O. BOX 361131 CLEVELAND, OHIO 44136-0019; Phone: 1-800-800-7310, 1-330-220-4683
Download from Www.Somanuals.com. All Manuals Search And Download.
|