Preface
Copyright
This publication, including all photographs, illustrations and software, is protected un-
der international copyright laws, with all rights reserved. Neither this manual, nor any
of the material contained herein, may be reproduced without w ritten consent of the au-
thor.
Version 3.1
Disclaimer
The information in this document is subject to change without notice. The manufac-
turer makes no representations or warranties with respect to the contents hereof and
specifically disclaims any implied warranties of merchantability or fitness for any par-
ticular purpose. The manufacturer reserves the right to revise this publication and to
make changes from time to time in the content hereof without obligation of the manu-
facturer to notify any person of such revision or changes.
Trademark Recognition
Microsoft, MS-DOS and Windows are registered trademarks of Microsoft Corp.
MMX, Pentium, Pentium-II, Pentium-III, Celeron are registered trademarks of Intel
Corporation.
Other product names used in this manual are the properties of their respective owners
and are acknowledged.
Federal Communications Commission (FCC)
This equipment has been tested and found to comply with the limits for a Class B digi-
tal device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instructions, may cause harmful interference
to radio communications. However, there is no guarantee that interference will not oc-
cur in a particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
-
-
-
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment onto an outlet on a circuit different from that to which
the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician for help.
Shielded interconnect cables and a shielded AC power cable must be employed with
this equipment to ensure compliance with the pertinent RF emission limits governing
this device. Changes or modifications not expressly approved by the system's manu-
facturer could void the user's authority to operate the equipment.
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE OF CONTENTS
Preface
i
Features and Packing List Translations
錯誤! 尚未定義書籤。
CHAPTER 1
1
Introducing the Mainboard
1
Introduction............................................................................................................1
Checklist.................................................................................................................1
Standard Items ................................................................................................... 1
Features..................................................................................................................2
Choosing a Computer Case................................................................................3
Mainboard Components.......................................................................................4
CHAPTER 2
5
Installing the Mainboard
5
Safety Precautions................................................................................................5
Quick Guide...........................................................................................................5
Installing the Mainboard in a Case.....................................................................6
Checking Jumper Settings...................................................................................6
Setting Jumpers ................................................................................................. 6
Checking Jumper Settings................................................................................. 7
Jumper Settings ................................................................................................. 7
Connecting Case Components...........................................................................8
The FPI Connector............................................................................................ 9
Installing Hardware.............................................................................................10
Installing the Processor................................................................................... 10
Installing Memory Modules ............................................................................ 11
Installing a Hard Disk Drive/CD-ROM .......................................................... 13
Installing a Floppy Diskette Drive .................................................................. 14
Installing Add-on Cards .................................................................................. 15
Connecting Optional Devices.......................................................................... 16
Connecting I/O Devices.....................................................................................18
CHAPTER 3
21
Using BIOS
21
About the Setup Utility........................................................................................21
The Standard Configuration............................................................................ 21
Running the Setup Utility................................................................................ 22
Using BIOS ..........................................................................................................22
Standard CMOS Features................................................................................ 23
Advanced Setup Page...................................................................................... 24
Management Setup Page ................................................................................. 25
Power Management Setup Page...................................................................... 26
iii
Download from Www.Somanuals.com. All Manuals Search And Download.
PCI / Plug and Play Setup ............................................................................... 27
Load Optimal Settings..................................................................................... 28
Load Best Performance Settings ..................................................................... 28
Features Setup Page......................................................................................... 28
CPU PnP Setup Page....................................................................................... 30
Hardware Monitor Page .................................................................................. 31
Change Password ............................................................................................ 32
Change or Remove the Password .................................................................... 32
Exit .................................................................................................................. 32
CHAPTER 4
33
Using the Mainboard Software
33
About the Software CD-ROM............................................................................33
Auto-installing under Windows 98....................................................................33
Running Setup................................................................................................. 35
Manual Installation..............................................................................................36
Utility Software Reference.................................................................................37
iv
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 1
Introducing the Mainboard
Introduction
Congratulations on purchasing the K7S5A mainboard. This mainboard has a
Socket-A processor socket for the type of AMD K7 processors. You can in-
stall any one of these processors on the mainboard. The mainboard supports
front-side bus speeds of 200/266MHz.
This mainboard uses the SiS 735 chipset which supports a 4X AGP slot for
highly graphics display, DDR interface and Ultra DMA 33/66/100 function,
provides outstanding high system performance under all types of system op-
erations. The mainboard has a built-in AC97 Codec, provides an AMR (Audio
Modem Riser) slot to support Audio and Modem application, and has a built-in
10BaseT/100BaseTX Network Interface. In addition, the mainboard has an
extended set of ATX I/O Ports including PS/2 keyboard and mouse ports, two
USB ports, a parallel port, and two serial ports. Two extra USB ports can be
added using the Extended USB Module that connects to the mainboard.
This mainboard has all the features you need to develop a powerful multim e-
dia workstation. The board is ATX size and has power connectors for an ATX
power supply.
Checklist
Compare the mainboard’ s package contents with the following checklist:
Standard Items
·
·
·
·
·
One mainboard
One diskette drive ribbon cable
One IDE drive ribbon cable
Software support CD
The User’ s Manual
Download from Www.Somanuals.com. All Manuals Search And Download.
Features
·
·
Supports AMD Athlon XP/Athlon/Duron processors
Supports 200/266 MHz Front-Side Bus
Processor
Note: Processors are automatically configured using
firmware and a synchronous Host/DRAM Clock
Scheme.
·
·
·
Two 168-pin DIMM slots for SDRAM memory modules
Two 184-pin DIMM slots for DDR memory modules
Support SDRAM up to 133 MHz /DDR up to 266 MHz
memory bus
Memory
·
Maximum installed memory is 1GB
Note: You cannot use SDRAM and DDR simultane-
ously.
·
·
·
·
·
·
·
One AMR slot for a special audio/modem riser card
One AGP4X slot for AGP 2.0-compliant interface
Five 32-bit PCI slots for PCI 2.2-compliant bus interface
Primary and Secondary PCI IDE channels
Support for PIO (programmable input/output) modes
Support for Multiword DMA modes
Expansion Slots
Onboard IDE
channels
Support for Bus Mastering and Ultra DMA 33/66/100
modes
·
·
ATX power supply connector
Meets ACPI 1.0b and APM 1.2 requirements, keyboard
power on/off
Supports RTC Alarm, Wake On Modem, AC97 Wake-Up
and USB Wake-Up
Power
Supply and
Power
Management
·
·
·
Compliant AC97 2.2 specification
AC’ 97 Audio
Codec
Supports 18-bit ADC (Analog Digital Converter) and DAC
(Digital Analog Converter) as well as 18-bit stereo full-
duplex codec
·
·
Built-in 10BaseT/100BaseTX Ethernet LAN
LAN controller integrates Fast Ethernet MAC and PHY
compliant with IEEE802.3u 100BASE-TX, 10BASE-T and
ANSI X3.263 TP-PMD standards
Built-in Ethernet
LAN (optional)
·
·
Compliant with ACPI 1.0 and the Network Device Class
Power Management 1.0
High Performance provided by 100Mbps clock generator
and data recovery circuit for 100Mbps receiver
Built-in Multi-threaded IO Link Delivering 1.2GB/s
Provides PC99 Color Connectors for easy peripheral
device connections
·
·
Onboard I/O
Ports
·
·
·
·
·
·
Floppy disk drive connector with 1Mb/s transfer rate
Two serial ports with 16550-compatible fast UART
One parallel port with ECP and EPP support
Two USB ports and optional two USB ports module
Two PS/2 ports for keyboard and mouse
One infrared port connector for optional module
Hardware Moni- Built-in hardware monitoring for CPU & System temperatures,
toring
fan speeds and mainboard voltages.
2
Download from Www.Somanuals.com. All Manuals Search And Download.
Onboard Flash
ROM
Supports Plug and Play configuration of peripheral devices
and expansion cards
Dimensions
ATX form factor (30.5cm x 24.4cm)
Choosing a Computer Case
There are many types of computer cases on the market. The mainboard com-
plies with the specifications for the ATX system case. Some features on the
mainboard are implemented by cabling connectors on the mainboard to indi-
cators and switches on the system case. Ensure that your case supports all
the features required. The mainboard can support one floppy diskette drive
and four enhanced IDE drives. Ensure that your case has sufficient power and
space for all the drives that you intend to install.
Most cases have a choice of I/O templates in the rear panel. Make sure that
the I/O template in the case matches the I/O ports installed on the rear edge
of the mainboard.
This mainboard has an ATX form factor of 30.5 x 24.4 cm. Choose a case that
accommodates this form factor.
This concludes Chapter 1. The next chapter explains how to install the main-
board.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
Mainboard Components
4
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 2
Installing the Mainboard
Safety Precautions
Follow these safety precautions when installing the mainboard:
·
·
Wear a grounding strap attached to a grounded device to avoid
damage from static electricity.
Discharge static electricity by touching the metal case of a safely
grounded object before working on the mainboard.
·
·
Leave components in the static-proof bags they came in.
Hold all circuit boards by the edges. Do not bend circuit boards.
Quick Guide
This Quick Guide suggests the steps you can take to assemble your system
with the mainboards.
The following table provides a reference for installing specific components:
Locating Mainboard Components
Installing the Mainboard in a Case
Setting Jumpers
Go to page 4
Go to page 6
Go to page 6
Go to page 8
Go to page 10
Go to page 11
Go to page 13
Go to page 14
Go to page 15
Go to page 16
Go to page 18
Installing Case Components
Installing the CPU
Installing Memory
Installing an HDD and CD-ROM Drive
Installing an FDD
Installing Add-on Cards
Connecting Options
Connecting Peripheral (I/O) Devices
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing the Mainboard in a Case
Refer to the following illustration and instructions for installing the mainboard
in a case:
This illustration shows an ex-
ample of a mainboard being
installed in a tower-type case:
2. Secure the mainboard with
screws where appropriate.
Note: Do not overtighten
the screws as this
can stress the main-
board.
Most system cases have
mounting brackets installed in
the case, which correspond to
the holes in the mainboard.
Place the mainboard over the
mounting brackets and secure
the mainboard onto the mount-
ing brackets with screws.
1. Place the mainboard
over the mounting brackets.
Ensure that your case has an I/O template that supports the I/O ports and
expansion slots on your mainboard.
Checking Jumper Settings
This section explains how to set jumpers for correct configuration of the main-
board.
Setting Jumpers
Use the mainboard jumpers to set system configuration options. Jumpers with
more than one pin are numbered. When setting the jumpers, ensure that the
jumper caps are placed on the correct pins.
The illustrations below show a 2-pin jumper. This illustration shows a 3-pin
When the jumper cap is placed on both pins, jumper. Pins 1 and 2 are SHORT.
the jumper is SHORT. If you remove the
jumper cap, or place the jumper cap on just
one pin, the jumper is OPEN.
1
2
3
Short
Open
6
Download from Www.Somanuals.com. All Manuals Search And Download.
Checking Jumper Settings
The following illustration shows the location of the mainboard jumpers. Pin 1 is
labeled.
Jumper Settings
Jumper
Type
Description
Setting (default)
JP1
3-pin
Keyboard Power 1-2: Disable Key-
On Selector
board Power On
JP1
JP4
1
1
2-3: Enable Key-
board Power On
JP4
3-pin
Clear CMOS
jumper
1-2: Clear CMOS
2-3: Normal
JP1: Keyboard Power On Selector
If you enable the keyboard power on feature, you can use hot keys on your
keyboard as a power on/off switch for the system.
Note: The system must provide 1A on the +5VSB (+5V Standby) signal before
using the Keyboard Power On function.
JP4: Clear CMOS Jumper
Use this jumper to clear the contents of the CMOS memory. You may need to
clear the CMOS memory if the settings in the Setup Utility are incorrect and
prevent your mainboard from operating. To clear the CMOS memory, discon-
7
Download from Www.Somanuals.com. All Manuals Search And Download.
nect all the power cables from the mainboard and then move the jumper cap
into the CLEAR setting for a few seconds.
Connecting Case Components
After you have installed the mainboard into a case, you can begin connecting
the mainboard components. Refer to the following:
1. Connect the power
connector from the
power supply to the
ATX_PWR1
connector on the
mainboard.
2. Connect the CPU
cooling fan cable to
CPUFAN.
3. If there is a cooling
fan installed in the
system chassis,
connect the cable
from the cooling fan to
the SYSFAN fan
power connector on
the mainboard.
4. Connect the case switches and indicator LEDs to the FP1 header JP2 for on-
board LAN LED.
5. Connect the case speaker cable to SPK1.
SPK1: Speaker Connector
Connect the cable from the PC speaker to the SPK1 header on the m ainboard.
Pin
Signal Name
1
2
3
4
SPKR
NC
Ground
+5V
JP2: Onboard LAN LED Connections
If you have a set indicator LEDs for the onboard LAN communication, you can
connect the LED cable to the header JP2.
Pins 1-2 are for Link LED. Pins 3-4 are for 10/100 Mbps mode LED, the on-
board LAN run in 100 Mbps mode when the LED lit.
8
Download from Www.Somanuals.com. All Manuals Search And Download.
Pin
Signal Name
1
2
3
4
Link LED
VCC
Ground
10/100 Mbps mode LED
The FPI Connector
This panel connector provides a set of switch and LED connectors found on
ATX case. Refer to the table below for information.
Device
HD_LED_P
FP PWR/SLP
HD_LED_N
RST_SW_N
RST_SW_P
KEY
Pins
1
1
2
2, 4
3
5, 8
6, 7
9, 10
9
10
Note: The plus sign (+) indicates a pin which must be connected to a positive
voltage.
9
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing Hardware
Installing the Processor
Caution: When installing a CPU heatsink and cooling fan make sure that
you DO NOT scratch the mainboard or any of the surface-mount resistors
with the clip of the cooling fan. If the clip of the cooling fan scrapes
across the mainboard, you may cause serious damage to the mainboard
or its components.
On most mainboards, there are small surface-mount resistors near the
processor socket, which may be damaged if the cooling fan is carelessly
installed.
Avoid using cooling fans with sharp edges on the fan casing and the
clips. Also, install the cooling fan in a well-lit work area so that you can
clearly see the mainboard and processor socket.
Before installing the Processor
This mainboard automatically determines the CPU clock frequency and sys-
tem bus frequency for the processor. You may be able to change these
settings by making changes to jumpers on the mainboard, or changing the
settings in the system Setup Utility. We strongly recommend that you do not
overclock processors or other components to run faster than their rated speed.
Warning: Overclocking components can adversely affect the reliability of
the system and introduce errors into your system. Overclocking can per-
manently damage the mainboard by generating excess heat in
components that are run beyond the rated limits.
This mainboard has a Socket 462 processor socket. When choosing a proc-
essor, consider the performance requirements of the system. Performance is
based on the processor design, the clock speed and system bus frequency of
the processor, and the quantity of internal cache memory and external cache
memory.
The following processors are currently supported by this mainboard.
Athlon XP: 1500+~2000+, FSB: 266 MHz
Athlon: 650 MHz~1.4 GHz, FSB: 200 MHz, 266 MHz
Duron: 550 MHz~ 1.3GHz, FSB: 200 MHz
CPU Installation Procedure
The following illustration shows CPU installation components:
10
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: The pin-1 corner is marked with an arrow
Follow these instructions to install the CPU:
1. Pull the CPU socket locking lever away from the socket to unhook it and raise
the locking lever to the upright position.
2. Identify the pin Pin-1 corner
on the CPU socket and the
pin Pin-1 corner on the
processor.
3. Match the Pin-1 corners and insert the processor into the socket. Do not use
force.
4. Swing the locking lever down and hook it under the latch on the edge of the
socket.
5. Apply thermal grease to the top of the CPU.
6. Lower the CPU fan/heatsink unit onto the CPU and CPU socket and then snap
then snap the fan/heatsink into place.
7. Plug the CPU fan power cable into the CPU cooling fan power supply on the
mainboard (CPUFAN).
Installing Memory Modules
The mainboard has two 168-pin/184-pin DIMM sockets for SDRAM/DDR
(Double Data Rate) SDRAM system memory modules.
11
Download from Www.Somanuals.com. All Manuals Search And Download.
DDR SDRAM provides 800 MBps or 1 GBps data transfer depending on
whether the bus is 100 MHz or 133 MHz. It doubles the rate to 1.6 GBps and
2.1 GBps by transferring data on both the rising and falling edges of the clock.
DDR SDRAM uses additional power and ground lines and requires 184-pin
2.5V unbuffered DIMM module rather than the 168-pin 3.3V unbuffered
DIMMs used by SDRAM.
Installation Procedure
You must install at least one memory
module in order to use the main-
board.
Note: You cannot use DDR
SDRAM and SDRAM
simultaneously.
Refer to the following to install the memory modules.
1.
2.
Push the latches on each side of the DIMM slot down.
Align the memory module with the slot. The DIMM slots are keyed with
notches and the DIMMs are keyed with cutouts so that they can only be
installed correctly.
3.
Check that the cutouts on the DIMM module edge connector match the
notches in the DIMM slot:
Latch
Latch
Cutout
Latch
Notch
Cutouts
Notches
Latch
DDR SDRAM Module
SDRAM Module
4.
5.
Install the DIMM module into the slot and press it firmly down until it
seats correctly. The slot latches are levered upwards and latch on to the
edges of the DIMM.
Install any remaining DIMM modules.
12
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing a Hard Disk Drive/CD-ROM
This section describes how to install IDE devices such as a hard disk drive
and a CD-ROM drive.
About IDE Devices
Your mainboard has a primary and secondary IDE channel interface (IDE1 and
IDE2). An IDE ribbon cable supporting two IDE devices is bundled with the main-
board.
If you want to install more than two IDE devices, get a second IDE cable and
you can add two more devices to the secondary IDE channel.
IDE devices have jumpers or switches that are used to set the IDE device as
MASTER or SLAVE. Refer to the IDE device user’ s manual. When installing two
IDE devices on one cable, ensure that one device is set to MASTER and the
other device is set to SLAVE. The documentation of your IDE device explains
how to do this.
About UltraDMA
This mainboard supports UltraDMA 66/100. UDMA is a technology that accel-
erates the performance of devices in the IDE channel. To maximize
performance, install IDE devices that support UDMA and use 80-pin IDE ca-
bles that support UDMA 66/100.
Installing a Hard Disk Drive
1. Install the hard disk drive into the drive cage in your system case.
2. Plug the IDE cable into IDE1
(A):
Note: Ribbon cable connectors
are usually keyed so that they can
only be installed correctly on the
device connector. If the connector
is not keyed, make sure that you
match the pin-1 side of the cable
connector with the pin-1 side of the
device connector. Each connector
has the pin-1 side clearly marked.
The pin-1 side of each ribbon ca-
ble is always marked with a
colored stripe on the cable.
3. Plug an IDE cable connector into the hard disk drive IDE connector (B). It
doesn't matter which connector on the cable you use.
4. Plug a power cable from the case power supply into the power connector on
the hard disk drive (C).
When you first start up your system, the BIOS should automatically detect
your hard disk drive. If it doesn’ t, enter the Setup Utility and use the IDE Hard
Disk Auto Detect feature to configure the hard disk drive that you have in-
stalled.
13
Download from Www.Somanuals.com. All Manuals Search And Download.
Installing a CD-ROM/DVD Drive
1. Install the CD-ROM/DVD drive into the drive cage in your system case.
2. Plug the IDE cable into IDE1
(A). If you have already installed
an HDD, use the other connec-
tor on the IDE cable.
Note: Ribbon cable connectors are
usually keyed so that they can only
be installed correctly on the device
connector. If the connector is not
keyed, make sure that you match the
pin-1 side of the cable connector with
the pin-1 side of the device connec-
tor. Each connector has the pin-1
side clearly marked. The pin-1 side of
each ribbon cable is always marked
with a colored stripe on the cable.
3. Plug an IDE cable connector into the CD-ROM/DVD drive IDE connector (B). It
doesn't matter which connector on the cable you use.
4. Plug a power cable from the case power supply into the power connector on
the CD-ROM/DVD drive (C).
5. Use the audio cable provided with the CD-ROM/DVD drive to connect to the
mainboard CD-in connector CDIN1 or CDIN2 (D).
When you first start up your system, the BIOS should automatically detect
your CD-ROM/DVD drive. If it doesn’ t, enter the Setup Utility and configure
the CD-ROM/DVD drive that you have installed.
Installing a Floppy Diskette Drive
The mainboard has a floppy diskette drive (FDD) interface and ships with a
diskette drive ribbon cable that supports one or two floppy diskette drives. You
can install a 5.25-inch drive and a 3.5-inch drive with various capacities. The
floppy diskette drive cable has one type of connector for a 5.25-inch drive and
another type of connector for a 3.5-inch drive.
1. Install the FDD into the drive cage in your system case.
2. Plug the FDD cable into FDC
(A):
Note: Ribbon cable connectors are
usually keyed so that they can only
be installed correctly on the device
connector. If the connector is not
keyed, make sure that you match the
pin-1 side of the cable connector with
the pin-1 side of the device connec-
tor. Each connector has the pin-1
side clearly marked. The pin-1 side of
each ribbon cable is always marked
with a colored stripe on the cable.
3. Plug the correct connector on the FDD cable for the 5.25-inch or 3.5-inch drive
into the FDD connector (B).
4. Plug a power cable from the case power supply into the power connector on
the FDD (C).
When you first start up your system, go immediately to the Setup Utility to
14
Download from Www.Somanuals.com. All Manuals Search And Download.
configure the floppy diskette drives that you have installed.
Installing Add-on Cards
This mainboard has five 32-bit PCI (Peripheral Components Interconnect)
expansion slots, one 4xAGP slot, and one AMR slot.
4xAGP Slot
PCI Slots
AMR Slot
The 4xAGP slot is used to install a graphics adapter that supports the
4xAGP specifications and has a 4xAGP edge connector.
PCI slots are used to install expansion cards that have the 32-bit PCI
interface.
The AMR (Audio Modem Riser) slot is an industry standard slot that
allows for the installation of a special audio/modem riser card. Differ-
ent territories have different regulations regarding the specifications
of a modem card. You can purchase an AMR card that is approved in
your area and install it directly into the AMR slot.
Note: Before installing an add-on card, check the documentation for the card
carefully. If the card is not Plug and Play, you may have to manually con-
figure the card before installation.
Follow these instructions to install an add-on card:
1. Remove a blanking plate from the system case corresponding to the slot you
are going to use.
15
Download from Www.Somanuals.com. All Manuals Search And Download.
2. Install the edge connector of the
add-on card into the expansion
slot. Ensure that the edge con-
nector is correctly seated in the
slot.
3. Secure the metal bracket of the card to the system case with a screw.
Note: For some add-on cards, for example graphics adapters and network adapters,
you have to install drivers and software before you can begin using the add-on
card.
Connecting Optional Devices
16
Download from Www.Somanuals.com. All Manuals Search And Download.
Refer to the following for information on connecting the mainboard’ s optional
devices:
FP_AUD1O: Front panel MIC/Speaker Out header
This header allows the user to install auxiliary front-oriented microphone and
line-out ports for easier access.
Pin
Signal Name
Pin
Signal Name
1
AUD_MIC
2
4
6
8
10
AUD_GND
AUD_VCC
GND
KEY
GND
3
5
7
9
AUD_MIC_BIAS
AUD_FPOUT_R
HP_ON
AUD_FPOUT_L
USB1: Extended USB header
The mainboard has USB ports installed on the rear edge I/O port array. Some
computer cases have a special module that mounts USB ports at the front of
the case. If you have this kind of case, use auxiliary USB connectors USB1 to
17
Download from Www.Somanuals.com. All Manuals Search And Download.
connect the front-mounted ports to the mainboard.
Pin
Signal Name
Pin
Signal Name
1
3
5
7
9
VERG_FP_USBPWR0
USB_FP_P0-
USB_FP_P0+
GROUND
2
4
6
8
10
VERG_FP_USBPWR0
USB_FP_P1-
USB_FP_P1+
GROUND
KEY
USB_FP_OC0
WOL1: Wake On LAN
If you have installed a LAN card, use the cable provided with the card to plug
into the mainboard WOL1 connector. This enables the Wake On LAN (WOL1)
feature. When your system is in a power-saving mode, any LAN signal auto-
matically resumes the system. You must enable this item using the Power
Management page of the Setup Utility.
Pin
Signal Name
1
5VSB
2
3
Ground
SENSE
IR1: Infrared port
The mainboard supports a Infrared (IR1) data port. Infrared ports allow the
wireless exchange of information between your computer and similarly
equipped devices such as printers, laptops, Personal Digital Assistants
(PDAs), and other computers.
Pin
Signal Name
Pin
Signal Name
1
2
3
NC
Key
+5V
4
5
6
Ground
IRTX
IRRX
Connecting I/O Devices
The backplane of the mainboard has the following I/O ports:
18
Download from Www.Somanuals.com. All Manuals Search And Download.
Parallel port (LPT1)
Game port
LAN
port
PS/2
mouse
PS/2
keyboard
USB Serial port Serial port
ports COM 1 COM 2
Microphone
Line-in
Line-out
PS/2 Mouse
Use the upper PS/2 port to connect a PS/2 point-
ing device.
PS/2 Ke yboard
Use the lower PS/2 port to connect a PS/2 key-
board.
LAN Port
(optional)
USB Ports
Use the LAN port to connect to the network.
Use the USB ports to connect USB devices.
LPT1
Use LPT1 to connect printers or other parallel
communications devices.
COM1/2
Use the COM ports to connect serial devices
such as mice or fax/modems. COM1 is identified
by the system as COM1/3. COM2 is identified by
the system as COM2/4.
Game Port
Use the game port to connect a joystick or a
MIDI device.
Audio Ports
Use the three audio ports to connect audio de-
vices. The left side jack is for a stereo line-out
signal. The middle jack is for a stereo line-in
signal. The right side jack is for a microphone.
External Connector Color Coding
Many connectors now use standard colors as shown in the table below.
Connector
Color
19
Download from Www.Somanuals.com. All Manuals Search And Download.
Audio line-in
Audio line-out
Light blue
Lime
Digital monitor/flat panel
IEEE 1394
White
Grey
Microphone
Pink
MIDI/game
Gold
Parallel
Burgundy
Purple
PS/2-compatible keyboard
PS/2-compatible mouse
Serial
Green
Teal or Turquoise
Orange
Brown
Black
Speaker out/subwoofer
Right-to-left speaker
USB
Video out
SCSI, network, telephone, modem
Yellow
None
This concludes Chapter 2. The next chapter covers the BIOS.
20
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 3
Using BIOS
About the Setup Utility
The computer uses the latest AMI BIOS with support for Windows Plug and
Play. The CMOS chip on the mainboard contains the ROM setup instructions
for configuring the mainboard BIOS.
The BIOS (Basic Input and Output System) Setup Utility displays the system's
configuration status and provides you with options to set system parameters.
The parameters are stored in battery-backed-up CMOS RAM that saves this
information when the power is turned off. When the system is turned back on,
the system is configured with the values you stored in CMOS.
The BIOS Setup Utility enables you to configure:
·
·
·
·
Hard drives, diskette drives, and peripherals
Video display type and display options
Password protection from unauthorized use
Power management features
The settings made in the Setup Utility affect how the computer performs. Be-
fore using the Setup Utility, ensure that you understand the Setup Utility
options.
This chapter provides explanations for Setup Utility options.
The Standard Configuration
A standard configuration has already been set in the Setup Utility. However,
we recommend that you read this chapter in case you need to make any
changes in the future.
This Setup Utility should be used:
·
·
when changing the system configuration
when a configuration error is detected and you are prompted to
make changes to the Setup Utility
·
·
·
when trying to resolve IRQ conflicts
when making changes to the Power Management configuration
when changing the password or making other changes to the Secu-
rity Setup
Download from Www.Somanuals.com. All Manuals Search And Download.
Running the Setup Utility
Each time your computer starts, before the operating system loads, a mes-
sage appears on the screen that prompts you to “Hit <DEL> if you want to run
SETUP” . When you see this message, press the Delete key and the Main
menu page of the Setup Utility appears on your monitor.
AMIBIOS SIMPLE SETUP UTILITY – VERSION 1.21.06
(C) 2000 American Megatrends, Inc. All Rights Reserved
Standard CMOS Setup
Advanced Setup
Features Setup
CPU PnP Setup
Hardware Monitor
Change Password
Exit
Power Management Setup
PCI / Plug and Play Setup
Load Optimal Settings
Load Best Performance Settings
Esc : Quit
• ¯ ¬ ®: Select Item (Shift)F2 : Change Color F5 : Old Values
F6 Optimal values
:
F7 : Best performance values F10 : Save&Exit
Standard CMOS setup for changing time, date, hard disk type, etc.
BIOS Navigation Keys
The BIOS navigation keys are listed below:
Key
Function
Esc
Exits the current menu
Scrolls through the items on a menu
Modifies the selected field's values
¬ • ¯ ®
+/–/PU/PD
F10
Saves the current configuration and exits setup
Displays a screen that describes all key functions
Loads previously saved values to CMOS
Loads a minimum configuration for troubleshooting.
Loads an optimum set of values for peak performance
F1
F5
F6
F7
Using BIOS
When you start the Setup Utility, the main menu appears. The main menu of
the Setup Utility displays a list of the options that are available. A highlight
indicates which option is currently selected. Use the cursor arrow keys to
move the highlight to other options. When an option is highlighted, execute
the option by pressing <Enter>.
Some options lead to pop-up dialog boxes that prompt you to verify that you
wish to execute that option. Other options lead to dialog boxes that prompt
you for information.
Some options (marked with a triangle ) lead to submenus that enable you
22
Download from Www.Somanuals.com. All Manuals Search And Download.
to change the values for the option. Use the cursor arrow keys to scroll
through the items in the submenu.
In this manual, default values are enclosed in parenthesis. Submenu items
are denoted by a triangle
.
Standard CMOS Features
Use this page to set basic information such as the date, the time, the IDE de-
vices, and the diskette drives. If you press the F3 key, the system will
automatically detect and configure the hard disks on the IDE channels.
AMIBIOS SETUP – STANDARD CMOS SETUP
(C) 2000 American Megatrends, Inc. All Rights Reserved
Date (mm/dd/yy) : Mon Dec 17, 2001
Time (hh/mm/ss) : 13:53:25
LBA Blk PIO 32Bit
Type
Size Cyln Head WPcom Sec Mode Mode Mode Mode
On
Pri Master : Auto
Pri Slave : Auto
Sec Master : Auto
Sec Slave : Auto
On
On
On
Floppy Drive A : 1.44 MB 3 1/2
Floppy Drive B : Not Installed
Month : Jan – Dec
ESC : Exit
Day : 01 – 31
Year : 1901 – 2099
•¯ : Select Item
PU/PD/+/- : Modify
(Shift)F2 : Color
F3 : Detect All HDD
Date & Time
Use these items to set the system date and time
Pri Master/Pri Slave/Sec Master/Sec Slave
Use these items to configure devices connected to the Primary and Secon-
dary IDE channels. To configure an IDE hard disk drive, choose Auto. If the
Auto setting fails to find a hard disk drive, set it to User, and then fill in the
hard disk characteristics (Size, Cyls, etc.) manually. If you have a CD-ROM
drive, select the setting CDROM. If you have an ATAPI device with removable
media (e.g. a ZIP drive or an LS-120) select Floptical.
Floppy Drive A/Floppy Drive B
Use these items to set the size and capacity of the floppy diskette drive(s)
installed in the system.
23
Download from Www.Somanuals.com. All Manuals Search And Download.
Advanced Setup Page
Use this page to set more advanced information about your system. Take
some care with this page. Making changes can affect the operation of your
computer.
AMIBIOS SETUP – ADVANCED SETUP
(C) 2000 American Megatrends, Inc. All Rights Reserved
Quick Boot
Enabled
IDE-0
Floppy
CDROM
Yes
Disabled
On
Disabled
Disabled
Setup
1st Boot Device
2nd Boot Device
3rd Boot Device
Try Other Boot Devices
S.M.A.R.T. for Hard Disks
BootUp Num-Lock
Floppy Drive Swap
Floppy Drive Seek
Password Check
Boot To OS/2 > 64MB
L1 Cache
No
ESC : Quit
F1 : Help
•¯¬® : Select Item
Enabled
Enabled
Enabled
Normal
PU/PD/+/- : Modify
L2 Cache
System BIOS Cacheable
Timing Setting Mode
F5 : Old Values (Shift)F2 : Color
F6 : Load BIOS Defaults
SDR/DDR CAS Latency
Auto Detect DIMM/PCI Clk
Clk Gen Spread Spectrum
SPD
Disabled
Disabled
F7 : Load Setup Defaults
Quick Boot
If you enable this item, the system starts up more quickly be elimination some
of the power on test routines.
1st Boot Device/ 2nd Boot Device/ 3rd Boot Device
Use these items to determine the device order the computer uses to look for
an operating system to load at start-up time.
Try Other Boot Device
If you enable this item, the system will also search for other boot devices if it
fails to find an operating system from the first two locations.
S.M.A.R.T. for Hard Disks
Enable this item if any IDE hard disks support the S.M.A.R.T. (Self-Monitoring,
Analysis and Reporting Technology) feature.
BootUp Num-Lock
This item determines if the Num Lock key is active or inactive at system start-
up time.
Floppy Drive Swap
If you have two diskette drives installed and you enable this item, drive A be-
comes drive B and drive B becomes drive A.
24
Download from Www.Somanuals.com. All Manuals Search And Download.
Floppy Drive Seek
If you enable this item, your system will check all floppy disk drives at start up.
Disable this item unless you are using an old 360KB drive.
Password Check
If you have entered a password for the system, use this item to determine if
the password is required to enter the Setup Utility (Setup) or required both at
start-up and to enter the Setup Utility (Always).
Boot to OS/2 > 64MB
Enable this item if you are booting the OS/2 operating system and you have
more than 64MB of system memory installed.
L1/L2 Cache
Leave these items enabled since all the processors that can be installed on
this board have internal cache memory.
System BIOS Cacheable
If you enable this item, a segment of the system BIOS will be cached to main
memory for faster execution.
Timing Setting Mode
Use this item to determine the timing setting mode of the memory. We rec-
ommend that you leave this item at the default value.
SDR/DDR CAS Latency
This item determines the operation of the SDRAM /DDR memory CAS (col-
umn address strobe). We recommend that you leave this item at the default
value. The 2T setting requires faster memory that specifically supports this
mode.
Auto Detect DIMM/PCI Clk
Use this item to enable the DIMMs or PCI slots to detect automatically device
then generating clock.
Clk Gen Spread Spectrum
Use this item to enable the clock to generate spread spectrum.
25
Download from Www.Somanuals.com. All Manuals Search And Download.
Power Management Setup Page
This page sets some of the parameters for system power management opera-
tion.
AMIBIOS SETUP – POWER MANAGEMENT SETUP
(C) 2000 American Megatrends, Inc. All Rights Reserved
ACPI Aware O/S
Yes
Power Management
Suspend Time Out
Hard Disk Time Out
Ring On Power On
RTC Alarm Power On
RTC Alarm Date
Enabled
Disabled
Disabled
Disabled
Disabled
Every Day
12
ESC : Quit
F1 : Help
•¯¬® : Select Item
PU/PD/+/- : Modify
RTC Alarm Hour
F5 : Old Values (Shift)F2 : Color
F6 : Load Optimal values
RTC Alarm Minute
RTC Alarm Second
KeyBoard PowerOn Function Disabled
30
00
F7 : Load Best performance values
Power On by LAN
Disabled
ACPI Aware O/S
Enable this item if you are using an O/S that supports ACPI function such as
Windows 98/ME /2000.
Power Management
Use this item to select a power management scheme. Both APM and ACPI
are supported.
Suspend Time Out
This sets the timeout for Suspend mode in minutes. If the time selected
passes without any system activity, the computer will enter power-saving Sus-
pend mode.
Hard Disk Time Out
This sets the timeout to power down the hard disk drive, if the time selected
passes without any hard disk activity.
Ring On Power On
The system can be turned off with a software command. If you enable this
item, the system can automatically resume if there is an incoming call on the
Fax/Modem. You must use an ATX power supply in order to use this feature.
RTC Alarm Power On / Date / Hour / Minute / Second
The system can be turned off with a software command. If you enable this
item, the system can automatically resume at a fixed time based on the sys-
tem’ s RTC (realtime clock). Use the items below this one to set the date and
time of the wake-up alarm. You must use an ATX power supply in order to use
this feature.
26
Download from Www.Somanuals.com. All Manuals Search And Download.
KeyBoard Power On Function
If you enable this item, you can turn the system on and off by pressing hot
keys on the keyboard. You must enable the Keyboard Power On jumper and
use an ATX power supply in order to use this feature.
Power On by LAN
Your system can enter a software power down. If you enable this item, the
system can automatically resume if there is traffic on the network adapter.
PCI / Plug and Play Setup
This page sets some of the parameters for devices installed on the PCI bus
and devices that use the system plug and play capability.
AMIBIOS SETUP – PCI / PLUG AND PLAY SETUP
(C) 2000 American Megatrends, Inc. All Rights Reserved
Plug and Play Aware O/S
Primary Graphics Adapter
Allocate IRQ to PCI VGA
Yes
PCI
Yes
ESC : Quit
F1 : Help
•¯¬® : Select Item
PU/PD/+/- : Modify
F5 : Old Values (Shift)F2 : Color
F6 : Load BIOS Defaults
F7 : Load Setup Defaults
Plug and Play Aware O/S
Enable this item if you are using an O/S that supports Plug and Play such as
Windows 95/98/ME.
Primary Graphics Adapter
This item indicates if the primary graphics adapter uses the PCI or the AGP
bus. The default PCI setting still lets the onboard display work and allows the
use of a second display card installed in a PCI slot.
Allocate IRQ to PCI VGA
If this item is enabled, an IRQ will be assigned to the PCI VGA graphics sys-
tem. You set this value to No to free up an IRQ.
27
Download from Www.Somanuals.com. All Manuals Search And Download.
Load Optimal Settings
If you select this item and press Enter a dialog box appears. If you press Y,
and then Enter, the Setup Utility loads a set of fail-safe default values. These
default values are not very demanding and they should allow your system to
function with most kinds of hardware and memory chips.
Note: It is highly recommended that users enter this option to load optimal val-
ues for accessing the best performance.
Load Best Performance Settings
If you select this item and press Enter a dialog box appears. If you press Y,
and then Enter, the Setup Utility loads a set of best-performance default val-
ues. These default values are quite demanding and your system might not
function properly if you are using slower memory chips or other low-
performance components.
Features Setup Page
This page sets some of the parameters for peripheral devices connected to
the system.
AMIBIOS SETUP – FEATURES SETUP
(C) 2000 American Megatrends, Inc. All Rights Reserved
OnBoard FDC
Enabled
3F8h/COM1
2F8h/COM2
Normal
378h
Normal
7
OnBoard Serial PortA
OnBoard Serial PortB
Serial Port2 Mode
OnBoard Parallel Port
Parallel Port Mode
Parallel Port IRQ
Parallel Port DMA
OnBoard Game Port
OnBoard MIDI Port
MIDI Port IRQ
OnBoard PCI IDE
OnBoard AC’ 97 Sound
N/A
ESC : Quit
F1 : Help
•¯¬® : Select Item
201h
300h
10
Both
Enabled
PU/PD/+/- : Modify
F5 : Old Values (Shift)F2 : Color
F6 : Load BIOS Defaults
OnBoard AC’ 97 Modem
USB Function Support
USB Function for DOS
Enabled
Enabled
Disabled
F7 : Load Setup Defaults
OnBoard FDC
Use this item to enable or disable the onboard floppy disk drive interface.
OnBoard Serial PortA/B
Use these items to enable or disable the onboard COM1/2 serial port, and to
assign a port address.
Serial Port2 Mode
Use this item to allocate the resources of the second serial port. Under Nor-
mal, the resources are allocated to the onboard serial port. Under ASKIR or
IrDA, the resources are allocated to the onboard IR port.
28
Download from Www.Somanuals.com. All Manuals Search And Download.
Onboard Parallel Port
Use this item to enable or disable the onboard LPT1 parallel port, and to as-
sign a port address. The Auto setting will detect and available address.
Parallel Port Mode
Use this item to set the parallel port mode. You can select SPP (Standard
Parallel Port), ECP (Extended Capabilities Port), EPP (Enhanced Parallel
Port), or ECP + EPP.
Parallel Port IRQ
Use this item to assign either IRQ 5 or 7 to the parallel port.
Parallel Port DMA
Use this item to assign a DMA channel to the parallel port. The options are 0,
1 and 3.
OnBoard Game Port
Use this item to enable or disable the onboard Game port.
OnBoard MIDI Port
Use this item to enable or disable the onboard MIDI port, and to assign a port
address.
MIDI Port IRQ
Use this item to assign an IRQ to the MIDI port.
Onboard PCI IDE
Use this item to enable or disable either or both of the onboard Primary and
Secondary IDE channels.
Onboard AC’ 97 Sound
This item enables or disables the onboard AC’ 97 audio chip.
Onboard AC’97 Modem
This item enables or disables the onboard AC’ 97 modem chip.
USB Function Support
Enable this item if you plan to use the USB ports on this mainboard.
USB Function for DOS
Enable this item if you plan to use the USB ports on this mainboard in a DOS
environment.
29
Download from Www.Somanuals.com. All Manuals Search And Download.
CPU PnP Setup Page
This page lets you manually configure the mainboard for the CPU. The sys-
tem will automatically detect the kind of CPU that you have installed and make
the appropriate adjustments to the items on this page.
AMIBIOS SETUP – CPU PnP Setup Page
(C) 2000 American Megatrends, Inc. All Rights Reserved
CPU Brand
CPU Type
AMD K7
Athlon
CPU Speed
CPU Core Voltage
CPU Ratio
700MHz
1.700 V
7.0
CPU Frequency
DRAM Frequency
100MHz
100MHz
ESC : Quit
F1 : Help
•¯¬® : Select Item
PU/PD/+/- : Modify
F5 : Old Values (Shift)F2 : Color
F6 : Load Optimal values
F7 : Load Best performance values
CPU Brand/Type/ Core Voltage/Ratio /Frequency
These items show the kind, core voltage, ratio and frequency of CPU that has
installed in your system.
CPU Speed
Use this item to set the CPU speed that has installed in your system.
DRAM Frequency
Use this item to set the frequency of DRAM that has installed in your system.
Note: If you manually set the wrong speed and the system won’ t run properly,
press the Page Up key while the system is booting and a default setting
will replace the incorrect CPU setting.
30
Download from Www.Somanuals.com. All Manuals Search And Download.
Hardware Monitor Page
This page sets some of the parameters for the hardware monitoring function
of this mainboard.
AMIBIOS SETUP – Hardware Monitor Page
(C) 2000 American Megatrends, Inc. All Rights Reserved
--- System Hardware ---
Vcore
2.000 V
Vcc2.5V
Vcc3.3V
Vcc5V
+12V
SB3V
-12V
SB5V
VBAT
2.500 V
3.300 V
5.000 V
12.000 V
3.300 V
-12.000 V
5.000 V
3.300 V
ESC : Quit
F1 : Help
•¯¬® : Select Item
System Fan Speed
CPU Fan Speed
System Temperature
CPU Temperature
PU/PD/+/- : Modify
F5 : Old Values (Shift)F2 : Color
F6 : Load Optimal values
F7 : Load Best Performance Values
30°C/86°F
Voltage Measurements & FAN Speeds
These items indicate cooling fan speeds in RPM and the various system volt-
age measurements.
System / CPU Temperature
These items display CPU and system temperature measurement.
31
Download from Www.Somanuals.com. All Manuals Search And Download.
Change Password
If you highlight this item and press Enter, a dialog box appears which lets you
enter a Supervisor password. You can enter no more than six letters or num-
bers. Press Enter after you have typed in the password. A second dialog box
asks you to retype the password for confirmation. Press Enter after you have
retyped it correctly. The password is then required to access the Setup Utility
or for that and at start-up, depending on the setting of the Password Check
item in Advanced Setup.
Change or Remove the Password
Highlight this item, press Enter and type in the current password. At the next
dialog box, type in the new password, or just press Enter to disable password
protection.
Exit
Highlight this item and press Enter to save the changes that you have made
in the Setup Utility configuration and exit the program. When the Save and
Exit dialog box appears, press Y to save and exit, or press N to exit without
32
Download from Www.Somanuals.com. All Manuals Search And Download.
Chapter 4
Using the Mainboard Software
About the Software CD-ROM
The support software CD-ROM that is included in the mainboard package
contains all the drivers and utility programs needed to properly run the bun-
dled products. Below you can find a brief description of each software
program, and the location for your mainboard version. More information on
some programs is available in a README file, located in the same directory
as the software.
Note: Never try to install software from a folder that is not specified for use with
your mainboard.
Before installing any software, always inspect the folder for files named RE-
ADME.TXT, INSTALL.TXT, or something similar. These files may contain
important information that is not included in this manual
Auto-installing under Windows 98
The Auto-install CD-ROM makes it easy for you to install the drivers and soft-
ware for your mainboard.
Note: If the Auto-install CD-ROM does not work on your system, you can still in-
stall drivers through the file manager for your OS (for example, Windows
Explorer). Refer to Utility Folder Installation Notes later in this chapter.
The support software CD-ROM disc loads automatically under Windows 98.
When you insert the CD-ROM disc in the CD-ROM drive, the autorun feature
will automatically bring up the install screen. The screen has three buttons on
it, Setup, Browse CD and Exit.
33
Download from Www.Somanuals.com. All Manuals Search And Download.
Note: If the opening screen doesn't appear, double-click the file "setup.exe" in
the root directory.
Setup Tab
Setup
Click the Setup button to run the software installation program.
Select from the menu which software you want to install.
Browse
CD
The Browse CD button is the standard Windows command that
allows you to open Windows Explorer and show the contents of
the support CD.
Before installing the software from Windows Explorer, look for a
file named README.TXT, INSTALL.TXT or something similar.
This file may contain important information to help you install the
software correctly.
Some software is installed in separate folders for different oper-
ating systems, such as DOS, WIN NT, or WIN98/95. Always go
to the correct folder for the kind of OS you are using.
To install the software, execute a file named SETUP.EXE or
INSTALL.EXE by double-clicking the file and then following the
instructions on the screen.
Exit
The Exit button closes the Auto Setup window.
Application Tab
Lists the software utilities that are available on the CD.
Read Me Tab
Displays the path for all software and drivers available on the CD.
34
Download from Www.Somanuals.com. All Manuals Search And Download.
Running Setup
Follow these instructions to install device drivers and software for the main-
board:
1.
Click Setup. The installation program begins:
Mainboard ID
Note: The following screens are examples only. The screens and driver lists will
be different according to the mainboard you are installing.
The mainboard identification is located in the upper left-hand corner.
2.
Click Next. The following screen appears:
3.
4.
Check the box next to the items you want to install. The default options
are recommended.
Click Next run the Installation Wizard. An item installation screen ap-
pears:
35
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Follow the instructions on the screen to install the items.
Drivers and software are automatically installed in sequence. Follow the on-
screen instructions, confirm commands and allow the computer to restart a
few times to complete the installation.
Manual Installation
Insert the CD in the CD-ROM drive and locate the PATH.DOC file in the root
directory. This file contains the information needed to locate the drivers for
your mainboard.
Look for the chipset and mainboard model; then browse to the directory and
path to begin installing the drivers. Most drivers have a setup program
(SETUP.EXE) that automatically detects your operating system before instal-
lation. Other drivers have the setup program located in the operating system
subfolder.
If the driver you want to install does not have a setup program, browse to the
operating system subfolder and locate the readme text file (README.TXT or
README.DOC) for information on installing the driver or software for your
operating system.
36
Download from Www.Somanuals.com. All Manuals Search And Download.
Utility Software Reference
All the utility software available from this page is Windows compliant. They are
provided only for the convenience of the customer. The following software is
furnished under license and may only be used or copied in accordance with
the terms of the license.
Note: These software(s) are subject to change at anytime without prior notice.
Please refer to the support CD for available software.
AMI Flash Memory Utility
This utility lets you erase the system BIOS stored on a Flash Memory chip on
the mainboard, and lets you copy an updated version of the BIOS to the chip.
Proceed with caution when using this program. If you erase the current BIOS
and fail to write a new BIOS, or write a new BIOS that is incorrect, your sys-
tem will malfunction. Refer to Chapter 3, Using BIOS for more information.
WinFlash Utility
The Award WinFlash utility is a Windows version of the DOS Award BIOS
flash writer utility. The utility enables you to flash the system BIOS stored on a
Flash Memory chip on the mainboard while in a Windows environment. This
utility is currently available for WINXP\ME\2000\98SE. To install the WinFlash
utility, run WINFLASH.EXE from the following directory:
\UTILITY\WINFLASH 1.51
PC-CILLIN
The PC-CILLIN software program provides anti-virus protection for your sys-
tem. This program is available for Windows 2000/ME/98SE and Windows NT.
Be sure to check the readme.txt and install the appropriate anti-virus software
for your operating system.
We strongly recommend users to install this free anti-virus software to help
protect your system against viruses.
MediaRing Talk – Telephony Software
To install the MediaRing Talk voice modem software for the built-in modem, go
to the directory \UTILITY\MEDIARING TALK, then run MRTALK-
SETUP72.EXE to install the application software.
Super Voice – Fax/Modem Software
To install the Super Voice voice, fax, data communication application for use
with the built-in fax/modem, go the directory \UTILITY\SUPER_VOICE, then
run PICSHELL.EXE to install the application software.
37
Download from Www.Somanuals.com. All Manuals Search And Download.
CD Ghost
The CD Ghost software enables you to create a virtual cabinet of CD-ROM
drives on your system to help you categorize and organize your CD collection.
A user-friendly interface assists you in quickly creating images of both CDs
and DVDs onto your system. To install the software, run SETUP.EXE from the
following directory:
\UTILITY\CDGHOST\ENG\CDGHOST
Recovery Genius
The Recovery Genius software program is an innovative windows application
system that protects your Hard Disk Drive from virus intrusion, accidental de-
letions and from system corruption. To install the Recovery Genius software
program run SETUP.EXE from the following directory:
\UTILITY\RECOVERY GENIUS\ENG\RECOVERYGENIUS
Language Genius
The Language Genius is a software –based product that helps you to learn
new languages. To install the Language Genius software program run
SETUP.EXE from the following directory:
\UTILITY\LANGUAGE GENIUS\ENG\LANGUAGEGENIUS
PageABC
The PageABC application software enables you to create your very own home
page. To install the PageABC, go to the directory \UTILITYPageABC, and
then run SETUP.EXE to install the application software.
This concludes Chapter 4.
38
Download from Www.Somanuals.com. All Manuals Search And Download.
|