DX-1 Disc Publisher Installation
Quick Reference Guide
1. Once the Hardware Installation is complete, verify that the printer is fully powered
For a more in-depth look at the installation process, please refer
to the Installation section of the User’s Manual.
PrassiTech Zulu2 Installation:
on and the connections to the computer are secure.
1. Click the Next button to begin the Zulu2 installation process.
2. Turn on the computer to which
the DX-1 Disc Publisher is
connected. Once the computer
boots, you will be notified that the
new USB connection has been
found.
Hardware Installation:
2. After the installation process completes, remove the check from the Reboot
Computer box and click Finish. Rebooting will occur after installing SureThing.
1. Unpack the DX-1 Disc Publisher and place it
in the selected workspace. This space
should have enough vertical space to allow
for easy loading of media into the input
hopper and have enough room at the back
to allow for any rejected discs to exit the DX-
1 Disc Publisher without obstacles.
SureThing CD Labeler Installation:
1. Click the Start button and select Run from the Start menu. Click the Browse
button and go to the CD/DVD drive, highlight SureThing.exe and click the
Open button, then click OK.
3. Click the Next button.
4. Place the DX-1 Disc Publisher
Software CD into the CD/DVD
ROM drive.
2. Read the Software License and Warranty information and click the I Accept
2. Plug the power cord into the back of the DX-1
button to continue the installation of SureThing.
Disc Publisher and turn on the switch above the
cord. Next, press the power button on the front panel to turn on the printer.
3. Click the Next button at the Welcome screen.
5. Windows 2000: Select the option to Search for a suitable driver, and click
Next. Check the CD-ROM Drives Box and click Next. Click the Next button
again when you are notified that the driver has been found.
4. To install to the default
directory, click Next on the
Select Destination Directory
screen. If you wish to install to
a different location, select that
location before clicking Next.
3. Install the 3 Input Rods and attach the Output Bin using the thumbscrews.
The wide Input Rod should be installed in the right-hand position, as marked.
Windows XP: Select the option to Install from a list or specific location and
click Next. Check the Search Removable Media box and click Next.
4. Install the Microboards ink cartridges.
THE DX-1 DISC PUBLISHER WILL ONLY OPERATE WITH
MICROBOARDS INK CARTRIDGE MODELS PRF19ML AND PRF38ML.
6. Once the USB drivers have been copied, click the Finish button.
7. A second USB driver installation will occur next. Repeat steps 3 through 6.
5. Select adding a desktop
shortcut and the location in
which the Start Menu shortcut
will be created, or make no
changes to select the default
locations. Click Next when the
locations are suitable.
A. Remove the tape from the front of the DX-1 Disc Publisher, lift the lid, and
remove the tape from the print carriage when it is in the center of the printer.
8. The Print driver installation will occur next. Repeat steps 3 through 6 to install
the print drivers. If the Digital Signature screen appears, click the Yes or Continue
Anyway button at the bottom of the screen. The drivers will then be copied to
the hard drive.
B. Raise the cradle latches. Remove the ink cartridges from the packaging
and carefully remove the plastic tape covering the print head.
C. Gently insert the ink cartridges into the appropriate cradles. Do not try to
force the cartridges into place as doing so may damage the cartridge.
NOTE: The USB and print driver installations may occur in a different order than
that listed above. This will not affect the operation of the DX-1.
6. Click Start on the next screen to install the application.
D. Secure the cradle latches and close the lid. The print carriage will return to
the right neutral position.
9. Verify the installation of the DX-1 Disc Publisher by clicking the Start button.
Select Printers and Faxes from the Start menu, either through the Settings
menu for Windows 2000 or directly in the Start menu for Windows XP. You will
see the new printer installed and available for use.
7. Click Finish once the installation is complete. You will also have the opportunity
to register the software on-line.
5. Connect the DX-1 Disc Publisher to the computer using the USB cable provided.
Please be sure the computer is off during this process.
8. The driver and software installation is now
complete. The computer will need to be
rebooted for the software to operate correctly.
Click OK to reboot. If you choose not to
reboot at this time, click the Cancel button
to reboot later. Remember, the computer
must be rebooted prior to running the DX-1
Disc Publisher, Zulu2, or SureThing.
A. Plug the small end of the USB cable into the back of the DX-1 Disc Publisher.
DX-1 Disc Publisher controller and Software Installation:
B. Plug the larger end of the USB cable into an available USB 2.0
port on the PC. Confirm that both ends of the cable are securely
connected.
The DX-1 Disc Publisher controllers, PrassiTech Zulu 2, and SureThing Disk Labeler
are included on the Software disc.
DX-1 Disc Publisher Controller Installation:
6. Turn the PC on at this point.
1. Click the Start button and select Run from the Start menu. Click the Browse
button and go to the CD/DVD drive, highlight Publisher.exe, click the Open
button, then click OK.
The Hardware Installation is now complete. Proceed next to the installation of the
DX-1 Disc Publisher Drivers and Software.
Installation of the DX-1 Disc Publisher is complete. After rebooting,
the printer will need to be aligned and the robotics configured prior
to burning and printing disks. Please see the DX-1 Disc Publisher
Configuration Quick Reference Guide on the other side of this page,
or refer to the appropriate sections of the User’s Manual.
Driver Installation:
2. Click the Next button on the next window. Once the window reads Ready to
Install the Program, click the Install button. Click Finish once the installation
completes. The Zulu2 software installation will begin automatically.
Windows 2000 and Windows XP will find the new hardware and will step you through
the installation process.
820-00152-01 Rev B
Download from Www.Somanuals.com. All Manuals Search And Download.
|