OPERATORS AND PARTS MANUAL NO. 02-1-QD
FOR
3100 & 4100 SERIES
QUICK DUMP REAR UNLOAD BOX
3100 SERIES:
4100 SERIES
3116
3118
3120
4116
4118
4120
4122
MANUFACTURED BY
COUNTY HWY. A WEST
P.O. BOX 405
DORCHESTER, WISCONSIN 54425-0405
PHONE 715-654-5132 • FAX 715-654-5513
1-800-325-9103
WWW.MEYERMFG.COM
E-MAIL: [email protected]
08-00
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY
A brief definition of signal words that are used in this manual is as follows:
DANGER indicates an imminently hazardous situation which, if not avoided, WILL re-
sult in death or serious injury.
WARNING indicates a potentially hazardous situation which, if not avoided, COULD
result in death or serious injury.
CAUTION indicates a potentially hazardous situation which, if not avoided, MAY
result in minor or moderate injury. It is also used to alert against unsafe practices.
B
H
F
G
D
G
E
C (INSIDE SHIELD
CAUTION: READ ALL DECALS ON THE FORAGE BOX AND IN THIS MANUAL.
KEEP THESE DECALS CLEAN AND REPLACE ANY LOST OR DESTROYED DECALS.
BECOME FAMILIAR WITH ALL TRACTOR AND FORAGE BOX CONTROLS.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY DECALS
DECAL C.
PART #46-0001-26
DECAL A.
PART #46-0001-4
DECAL B.
PART #46-0001-12
DECAL D
PART #46-0011
DECAL F
PART #46-0001-62
DECAL E
PART #46-0001-33
DECAL G.
PART #46-0001-20
DECAL I.
PART #46-0001-35
DECAL H.
PART #46-0001-22
ADMA SAFETY MANUAL SUPPLIED
PART #46-0013
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY PRECAUTIONS
• This equipment can be hazardous in the hands of an unfamiliar, untrained or careless oper-
ator.
• For your safety you must not operate, service, inspect or otherwise handle this equipment
unless you have read the Owner’s Manual and have been properly trained in its intended
usage.
• Require anyone who will operate this machine to read and understand this manual. Give
necessary instructions.
• Do not operate until all shields, covers and guards are in place.
• Keep hands, feet and clothing away from moving parts. Loose or floppy clothing should not
be worn by the operator.
• Make certain everyone is clear of equipment before applying power.
• Do not allow minors (or children) or inexperienced person to operate this machine.
• Always shut off power and disconnect power take-off shaft or optional Hydraulic drive sup-
ply hoses (relieve hydraulic pressure) from tractor to prevent accidental startup or unex-
pected movement before working on machine.
• Make sure all hydraulic fittings are tight and that all hoses are in good condition. Hydraulic
fluid escaping under pressure can have sufficient force to penetrate skin and cause serious
injury. Never investigate for hydraulic leaks by using a part of the body to feel for escaping
fluid.
• If the machine becomes clogged, shut off the tractor engine and allow all mechanisms to
stop. Disconnect power take-off shaft or optional hydraulic drive supply hoses (relieve hy-
draulic pressure). Then clean or work on the machine as required.
• Do not step over the power take-off shaft. Stay clear of the power take-off shaft at all times.
• Stay well clear of the rear opening discharge while operating. Pressure of the forage
against this door may cause door to open quickly and with force when latch releases.
• Do not step up on any part of the dump box at any time.
• Keep power take-off shaft telescoping tube shields turning freely. Keep power take-off mas-
ter shield on tractor. Replace shields missing or damaged.
• Inspect when first delivered and regularly thereafter; that all connections and bolts are tight
and secure before operating.
• Never operate power take-off above its normal 540 RPM rating. Never connect dump box to
a 1000 RPM tractor power take-off.
• Do not tow at speeds in excess of 10 MPH.
• You must observe all applicable traffic laws when transporting on public roadways (where
legal to do so). Check local laws for all highway lighting and marking requirements.
• Always install a SMV emblem on dump box for transporting on roadways and keep this em-
blem clean.
FAILURE TO HEED MAY RESULT IN SERIOUS PERSONAL INJURY OR DEATH.
Page 6
Download from Www.Somanuals.com. All Manuals Search And Download.
PRE-OPERATION
Be sure your dump box is properly mounted
ARE TIGHT AND SECURE BEFORE OP-
ERATING. FAILURE TO HEED MAY RE-
SULT IN SERIOUS PERSONAL INJURY
OR DEATH.
to the running gear. Consult your dealer if
you have any questions about the tie down
kit from the manufacturer and illustrated in
the parts listing of this manual.
Inspect all adjustments on the machine to be
sure they are proper and to provide maxi-
mum performance. Lube the machine if it is
required.
This dump box is to be operated with 540
rpm PTO only. Set your tractor drawbar to
conform to the standard dimensions shown
drive shaft will not be over extended.
WARNING: DO NOT OPERATE
WITHOUT ALL SHIELDS, GUARDS AND
COVERS INSTALLED. FAILURE TO HEED
MAY RESULT IN SERIOUS PERSONAL IN-
JURY OR DEATH.
DANGER: DO NOT OPERATE
WITHOUT PTO GUARD ON MACHINE
AND ON TRACTOR. MAINTAIN PTO
DRIVE SHAFT GUARD TUBES IN OPER-
ATING CONDITION. REPLACE THEM IF
DAMAGED AND NOT TURNING FREELY.
FAILURE TO HEED MAY RESULT IN SERI-
OUS PERSONAL INJURY OR DEATH.
Before operation and after hitching the trac-
tor to the wagon, connect the PTO. Slowly
engage the tractor PTO and operate box at
idle speed to ensure it is operating properly.
WARNING: INSPECT REGULARLY
THAT ALL CONNECTIONS AND BOLTS
FIGURE 1. DRAWBAR & PTO
RELATIONSHIP
FIGURE 2. DUMP BOX
Page 7
Download from Www.Somanuals.com. All Manuals Search And Download.
TRANSPORTING
HIGHWAY LIGHTING AND MARKING RE-
QUIREMENTS.
WARNING: DO NOT TOW AT
SPEEDS GREATER THAN 10 MPH. FAIL-
URE TO HEED MAY RESULT IN SERIOUS
PERSONAL INJURY OR DEATH.
Be sure and observe that the rear discharge
door is latched closed before traveling on
roadways.
Operating speed is dictated by the terrain
over which you are traveling. Always use
caution. Avoid traveling on slopes or hills that
are unsafe.
WARNING: INSTALL A SMV EM-
BLEM ON REAR OF DUMP BOX FOR
TRANSPORTING ON ROADWAYS AND
KEEP THIS EMBLEM CLEAN. FAILURE TO
HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
Always disconnect the PTO drive shaft from
the tractor and return it to its storage bracket
on the front of the box for transporting, see
equipment damage.
If you will travel on public roads and it is legal
to do so, you must know all rules governing
such operation. This will include lighting and
brake requirements in addition to traffic
rules. You may also be required to install a
safety chain device on the running gear.
Check for traffic constantly. Be sure you can
see that no one is attempting to pass you and
that all traffic is sufficiently clear from you be-
fore making any turns.
FIGURE 3. PTO STORAGE
Your running gear probably has a telescop-
ing tongue for convenience to hitch up. Al-
ways back up and lock this tongue in the
operating position after hitching.
WARNING: YOU MUST OBSERVE
ALL APPLICABLE TRAFFIC LAWS WHEN
TRANSPORTING ON PUBLIC ROAD-
WAYS. CHECK LOCAL LAWS FOR ALL
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATION
WARNING: MAKE CERTAIN EV-
ERYONE IS CLEAR OF EQUIPMENT BE-
FORE APPLYING POWER. FAILURE TO
HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
Pull the dump box into position.
Always park as straight ahead as possible so
there is a minimum angle on the PTO shaft
U-joints when it is connected to the tractor.
Set the brakes and shut the tractor off.
NOTE: Normal operation is using a tractor. If
using some other vehicle exercise caution
when parking and exiting this vehicle.
Remove drive shaft from the storage bracket
and connect it to the tractor PTO. Be sure the
PTO yoke is securely locked to the tractor
PTO. If using an optional hydraulic drive,
couple the hydraulic hoses to the power sup-
ply.
FIGURE 4. REAR OPENING DISCHARGE
DOOR
Make sure all persons are clear of the dump
box and the unloading area.
cally as forage is forced against it. The door
can spring open with extreme force when the
the pressure of the forage against the door.
WARNING: DISCHARGE DOOR
CAN SPRING OPEN QUICKLY AND WITH
FORCE. KEEP ALL PERSONS WELL
CLEAR OF THE DUMP BOX AND UN-
LOADING AREA. FAILURE TO HEED MAY
RESULT IN SERIOUS PERSONAL INJURY
OR DEATH.
FIGURE 5. DOOR LATCH
(Typical both sides)
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Return to the tractor, restart, and slowly en-
gage the PTO to start the apron chains and
open the rear door. Once the door opens,
regulate the discharge flow with the tractor
PTO speed (or tractor hydraulic flow control
for hydraulic driven). Do not operate above
rated speed of 540 RPM.
comes clogged, shut off all power to the
dump box. Wait for all motion to stop. Dis-
connect PTO shaft or hydraulic supply
hoses. Then clean out machine. Never use
power to aid clean out. If any mechanism
fails, remove dump box to safe work area
and repair the mechanism before proceeding
with unloading.
WARNING: DO NOT STEP UP ON
ANY PART OF THE DUMP BOX AT ANY
TIME. FAILURE TO HEED MAY RESULT IN
SERIOUS PERSONAL INJURY OR
DEATH.
DANGER: NEVER ENTER THE
DUMP BOX WITHOUT FIRST DISCON-
NECTING PTO SHAFT FROM POWER
SUPPLY OR DISCONNECTING OPTIONAL
HYDRAULIC HOSES FROM POWER
SUPPLY. FAILURE TO HEED MAY RE-
SULT IN SERIOUS PERSONAL INJURY
OR DEATH.
Unloading is best observed from the tractor
seat. If you are at ground level, the front of
the box has a top section of expanded metal
for convenient observation.
Never enter the dump box for any reason if
there is any possibility of power being ap-
plied to the unit.
When finished unloading reduce speed to
idle and disengage the PTO drive. Pull the
dump box straight ahead to pull the door
away from the unloaded pile of forage. When
free gravity will allow the door to swing shut
and the door latches will engage the apron
chain links to secure it shut. Observe that this
happens properly. Set the brakes and turn
the tractor “OFF”. When all movement has
stopped, disconnect the PTO drive shaft
from the tractor and return it to its storage
bracket. Secure it with the rubber tie down
strap.
WARNING: DISCONNECT PTO
DRIVE SHAFT (OR OPTIONAL HYDRAU-
LIC
POWER
SOURCE)
BEFORE
CLEANING, ADJUSTING, LUBRICATING
OR SERVICING THIS MACHINE. FAILURE
TO HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
Allow box to completely clean out the last
load of forage. It is recommended to lube the
dump box before storage to exclude mois-
ture from bearings. Apply oil to roller chain
drives and to the apron chains. It is also a
good time to inspect all adjustments and
check for parts that need repair or replace-
ment. Performing these tasks now will guar-
antee that the box is ready for use at the
beginning of the next season.
WARNING: DO NOT STEP OVER
THE POWER TAKE-OFF SHAFT. STAY
CLEAR OF POWER TAKE-OFF SHAFT AT
ALL TIMES. FAILURE TO HEED MAY RE-
SULT IN SERIOUS PERSONAL INJURY
OR DEATH.
The unloading process described is to be ac-
complished by the operator alone. This will
eliminate unexpected startups and minimize
other hazards that can result by more than
one person in control. If the dump box be-
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTMENTS
WARNING: DISCONNECT PTO
DRIVE SHAFT (OR OPTIONAL HYDRAU-
LIC POWER SOURCE) BEFORE
CLEANING, ADJUSTING, LUBRICATING
OR SERVICING THIS MACHINE. FAILURE
TO HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
APRON CHAIN
Correct tension on the apron chains is when
about three feet of chain does not touch the
return slides at the rear of the box. To tighten
chains, tighten the adjuster bolts at each end
and center of the front sprocket shaft, see fig-
shaft. At the center cutout there is an ad-
juster bolt for each shaft. Tighten the adjuster
bolts at each end of each shaft equally.
ROLLER CHAIN DRIVES
The roller chain drives are tensioned by auto-
ADJUSTER
BOLTS
FIGURE 6. ADJUST APRON CHAINS
matic spring loaded tension blocks.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION
WARNING: DISCONNECT PTO DRIVE
SHAFT (OR OPTIONAL HYDRAULIC
POWER SOURCE) BEFORE CLEANING,
ADJUSTING, LUBRICATING OR SER-
VICING THIS MACHINE. FAILURE TO
HEED MAY RESULT IN SERIOUS PER-
SONAL INJURY OR DEATH.
Grease (2) Pto drive shaft joints daily.
Maintain oil in gearbox to centerline of
shafts. Use Multi purpose 80-90 transmis-
sion lube. Lighter oil may be used in temper-
atures lower than 20 degrees.
Grease the (3) main apron drive shaft
bearing at rear, weekly.
Grease jackshaft at rear, weekly.
Use light machine oil periodically on
the roller chain drives, weekly.
Grease (2) door hinges annually.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
FIGURE 7. LUBRICATION DIAGRAM
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
REPAIR PARTS
APRON - REAR UNLOAD QUICK DUMP
KEY PART NO.
DESCRIPTION
KEY PART NO.
DESCRIPTION
1
2
3
25-0146
25-0145
25-0144
25-0147
Tightener Bracket LH
Tightener Bracket CENTER
Tightener Bracket RH
Tightener Nut
11
11-0068-2
11-0008-3
24-0091
Attachment Link-D667H
Attachment Link-D667X
Front Shield with Hinges
Deflector Shield
12
13
15
16
24-0090
25-0141
11-0081-2
830-5013-6Z Tightener Bolt
Brkt, Deflector Shield Support
Chain Slat
4
5
6
10-0054
23-0043
11-0098
11-0085
11-0068-3
11-0008-1
11-0008-2
11-0080
Sprocket #67-6
Idler Shaft
w/attachments-667H
Chain Slat
Chain Assy (20ft.) 667X
Chain Assy (18ft.) 667X
Pintle Chain Link-D667H
Pintle Chain Link D667X
Rivet, 3/8x7/8
11-0084-2
w/attachments-667X
Bearing Support Bracket
Main Drive Shaft Bearing
Main Drive Shaft
7
17
18
20
23
25-0018
14-0009
23-0050
49-0006
8
10
Slat
Front Deflector Shield Belting
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
UNIVERSAL JOINT TELESCOPING ASSEMBLY
QUICK DUMP REAR UNLOAD
KEY
PART NO.
DESCRIPTION
18-0014
Joint Assy, W-90 Universal
Joint & Tube Half w/guard (implement half)
Repair Kit
1
18-0014-1
18-0001-4
18-0014-3
18-0005-17
18-0014-6
18-0014-7
18-0014-8
18-0014-9
18-0005-15
18-0005-16
18-0001-13
18-0001-14
2
3
Tube & Yoke
Nylon Bearing with Retainer
Inner Guard
5
6
7
Joint & Shaft Half w/guard (tractor half)
Outer Guard
Shaft & Yoke
8
9
10
11
16
17
Yoke Assy, Lock
Quik Lok Repair Kit
“W” Repair Kit w/2 pins
Pins, “W” Repair Kit
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
DRIVE TRAIN
QUICK DUMP REAR UNLOAD
(REAR)
(FRONT)
Page 16
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY
PART NO.
DESCRIPTION
1
2
3
4
6
7
8
24-0105-3
24-0105-2
24-0105-1
14-0003-2
14-0002-3
14-0003-1
23-0036
PTO Belting 6"x14"
PTO Belting 6"x10"
PTO Shield
1-1/4 Two Bolt Flange
1-1/4 Bearing w/Lock Collar
1-1/4 Pillow Block Flange
Main Drive Shaft 16ft.
Main Drive Shaft 18ft.
Main Drive Shaft 20ft.
PVC Pipe Guard 72"
Shaft Coupler
23-0035
23-0042
9
100-9990-20
37-0007
19-0016
10
11
12
13
14
15
16
17
18
19
20
21
22
23
27
28
29
30
32
33
34
35
36
Right Angle Gearbox
PVC Pipe Guard 30-1/2"
Cross Drive Shaft 42-3/8"
Idler Shaft Weldment
Output Shaft
100-9990-21
23-0037
23-0041
23-0049
910-0003
911-0004
10-0065
80B45 Sprocket
80-62 Roller Chain
Sprkt Wldt 80A12/60A48
Wood Tightener Block
Spring
901-3618-6
929-3601
811-3118-3Z
11-0041
Eye Bolt
60-66 Roller Chain
60B15 Sprocket
Support Arm
10-0062
25-0176
100-9990-22
25-0196-3
25-0195-3
25-0194
Idler Shaft Bolt w/Zerk
Idler Tightener Weldment
Drive Tightener Weldment
Spring Tightener Angle
Four Bolt Flange Bearing 1-1/2"
Rear Shield Frame
Tightener Catch
914-3602
24-0106-5
25-0196-4
24-0106
Cluster Shield
Page 17
Download from Www.Somanuals.com. All Manuals Search And Download.
TIE DOWN KIT FOR STEEL BOX
KEY
PART NO.
DESCRIPTION
52-0003S
25-0084
52-0003-1
Tie Down Kit (Steel Stringers)
Bracket
Chain
1
2
3
4
5
6
7
8
801-3816-1.5Z
805-0038-Z
815-3816-Z
801-5013-1.25-Z
805-0050-Z
815-5013-Z
Bolt, Hex Machine-3/8x1-1/2
3/8 Flat Washer
3/8 Lock Nut
Hex Machine Bolt 4 1/2x1-1/4
1/2 Flat Washers
1/2 Lock Nuts
Page 18
Download from Www.Somanuals.com. All Manuals Search And Download.
REAR DISCHARGE DOOR COMPONENTS
KEY
PART NO.
DESCRIPTION
1
2
3
4
5
6
7
8
9
25-0179
25-0190-1
Bearing Bracket Brace
Left Main Roller Bracket
Left Gate Side Frame
Latch Catch
100-9990-23
100-9990-25-12
100-9990-25-13
33-1002
Back Gate Frame
Slow Moving Vehicle Bracket
Back Gate Panel 40-3/4x84-1/4
Right Gate Side Frame
Right Main Roller Bracket
100-9990-25-13
100-9990-24
25-0191-1
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
DUMP BOX PARTS
4100 SERIES
(REAR)
(FRONT)
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY
PART NO.
DESCRIPTION
1
100-9990-53
100-9990-8-7
100-9990-15-4
31-0006-2
20’ Side Panel, 20 Ga x40-3/4 Painted
18’ Side Panel, 20 Ga x40-3/4 Painted
Back Roof Panel
2
3
Panel, Expanded Metal
4
100-9990-17-6
100-9990-8-2
100-9990-8-1
100-9990-8-6
100-9990-8-5
100-9990-8-4
100-9990-8-3
100-9990-53
100-9990-10
100-9990-51-1
100-9990-15-8
100-9990-26
100-9990-26-5
100-9990-61
100-9990-60
100-9990-69
100-9990-63-1
100-9990-70
100-9990-62-1
100-9990-31
100-9990-14-3
100-9990-54
100-9990-9
20 Ga Front End Gate Panel Painted
Rear Left, Upright, 10 Ga x82-1/2 (illustrated)
Rear Right, Upright, 10 Ga x82-1/2 (not illustrated)
Center Left, Upright, 10 Ga x82-1/2 (illustrated)
Center Right, Upright, 10 Ga x82-1/2 (not illustrated)
Front Left, Upright, 10 Ga x82-1/2 (illustrated)
Front Right, Upright, 10 Ga x82-1/2 (not illustrated)
Floor Complete 20ft.
5
6
7
8
9
10
11
Floor Complete 18ft.
Roof Panel Painted 21’3"
12
Roof Panel Painted 19’3"
Front End Gate, Complete
13
14
15
16
17
Front End Gate, Frame Only
Roof Angle Left (illustrated)
Roof Angle Right (not illustrated)
Left Roof Angle Ext. 20’ (illustrated)
Left Roof Angle Ext. 18’ (illustrated)
Right Roof Angle Ext. 20’ (not illustrated)
Right Roof Angle Ext. 18’ (not illustrated)
Back Gate Panel Angle
18
19
20
21
Roof Guard Strap
Left Side, Complete 20’ (illustrated)
Left Side, Complete 18’ (illustrated)
Right Side, Complete 20’ (not illustrated)
Right Side, Complete 18’ (not illustrated)
Roof Bow
22
100-9990-55
100-9990-8
23
24
100-9990-15-1
100-9990-50
100-9990-56
100-9990-1-4
100-9990-1-5
100-9990-50-1
100-9990-1-1
100-9990-32
100-9990-52-1
100-9990-8-8
25-0006
Bottom Frame, Complete 20’
Bottom Frame, Complete 18’
25
26
27
Back Cross Channel 94-1/2 w/Gussets
Cross Channels 94-1/2 w/Gussets
10" Channel Bed Piece (19’-10")
10" Channel Bed Piece (17’-10")
Side End Gate Cap Right
28
29
Top Rail 20’ TSS Side
Top Rail 18’ TSS Side
PTO Hanger Bracket
30
31
32
33
34
35
36
37
38
100-9990-28
100-9990-27
100-9990-33
100-9999-39
100-9999-38
100-9999-39
100-9999-38
100-9990-1-10
Right Front Roof Support Bracket
Left Front Roof Support Bracket
Side End Gate Cap Left
3" Side Channel Suport
Main Stringer Support
3" Side Channel Support (14’ & 16’ Floor Lengths)
Main Stringer -Support
Rear Steel Stringer, Reinforcing Plate
(18’+ Floor Lengths)
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
WELDED BOX PARTS (1 OF 2)
3100 SERIES
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY
PART NO.
DESCRIPTION
1
100-9995-19
100-9995-18
100-9995-17
100-9995-120-1
14’ Side Panel, 20 Ga x40-3/4 Aluminized
16’ Side Panel, 20 Ga x40-3/4 Aluminized
18’ Side Panel, 20 Ga x40-3/4 Aluminized
Back Roof Panel, 20-3/8x86 Aluminized
2
3
4
5
100-9990-8-2
100-9990-8-1
100-9990-8-6
100-9990-8-5
100-9990-8-4
100-9990-8-3
Rear Left, Upright, 10 Ga x 82-1/2"
(illustrated)
6
Front Right, Upright, 10 Ga x 82-1/2"
(not illustrated)
7
Center Left, Upright, 10Ga x 82-1/2"
(illustrated)
8
Center Right, Upright, 10 Ga x 82-1/2"
(not illustrated)
9
Front Left, Upright, 10 Ga x 82-1/2"
(illustrated)
10
11
Front Right, Upright, 10 Ga x 82-1/2"
(not illustrated)
Floor Complete 14’
100-9990-12
100-9990-11
100-9990-10
100-9990-13-2
100-9990-14-2
100-9990-15-8
Floor Complete 16’
Floor Complete 18’
12
Roof Panel Painted 15’ 3"
Roof Panel Painted 17’ 3"
Roof Panel Painted 19’ 3"
13
14
15
16
17
100-9990-61
100-9990-60
100-9990-67-1
100-9990-65-1
100-9990-63-1
100-9990-66-1
100-9990-64-1
100-9990-62-1
100-9990-15-9
100-9990-14-3
100-9994-4
Roof Angle Left (illustrated)
Roof Angle Right (not illustrated)
Left Roof Angle Ext. 14’ (illustrated)
Left Roof Angle Ext. 16’ (illustrated)
Left Roof Angle Ext. 18’ (illustrated)
Right Roof Angle Ext. 14’ (not illustrated)
Right Roof Angle Ext. 16’ (not illustrated)
Right Roof Angle Ext. 18’ (not illustrated)
Back Gate Panel Angle
18
19
20
21
Roof Guard Strap
Left Side, Complete 14’ (illustrated)
Left Side, Complete 16’ (illustrated)
Left Side, Complete 18’ (illustrated)
Right Side, Complete 14’ (not illustrated)
Right Side, Complete 16’ (not illustrated)
Right Side, Complete 18’ (not illustrated)
Roof Bow
100-9994-6
100-9994-8
22
100-9994-5
100-9994-7
100-9994-9
23
24
100-9990-15-1
100-9994-1
100-9994-2
Bottom Frame, Complete 14’
Bottom Frame, Complete 16’
100-9994-3
100-9990-1-3
100-9994-1-3
Bottom Frame, Complete 18’
Back Cross Channel 94-1/2"
Back Cross Channel Gusset
25
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
WELDED BOX PARTS (2 OF 2)
3100 SERIES
Page 24
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY
26
PART NO.
DESCRIPTION
100-9990-1-2
100-9994-1-1
100-9990-3-1
100-9990-2-1
100-9990-1-1
Cross Channel 94-1/2"
Cross Channel Gusset
10" Channel Bed Piece (13’-10")
10" Channel Bed Piece (15’-10")
10" Channel Bed Piece (17’-10")
Side End Gate Cap
27
28
29
100-9990-4-2
100-9990-6-2
100-9990-8-8
100-9999-39
100-9994-1-2
100-9999-2-3
100-9998-7
Top Rail 14’
Top Rail 16’
Top Rail 18’
30
31
32
33
Stringer Support Channel
Stringer Support Cross Angle
Cross Channel Center U Piece
14’ Chain Slide
100-9998-8
100-9999-5
16’ Chain Slide
18’ Chain Slide
34
35
36
100-9995-120
100-9997-1
100-9997-2
Rear Roof Assy Complete
Center Floor Support, 2x6x14’
Center Floor Support, 2x6x16’
Center Floor Support, 2x6x18’
Outer Floor Support 3x6x14’
Outer Floor Support 3x6x16’
Outer Floor Support 3x6x18’
Chain Rail Tab
100-9999-6
100-9998-9
37
100-9998-10
100-9999-7
38
39
100-9994-1-5
100-9995-133
100-9995-134
100-9995-135
3514 Roof Assy., Complete
3516 Roof Assy., Complete
3518 Roof Assy., Complete
Page 25
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 26
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 27
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
|