Metra Electronics Satellite Radio 95 7801 User Manual

INSTALLATION INSTRUCTIONS FOR PART 95-7801  
APPLICATIONS  
See Application List Inside  
95-7801  
KIT FEATURES  
• Double DIN Radio Provision  
• Stacked ISO Units Provision  
KIT COMPONENTS  
• A) Radio Housing • B) Rear Support Tray • C) ISO Brackets  
• D) Mounting Bracket (Acura legend) • E) (2) #8 x 1/2” Phillips Pan Head Screws  
• F) (6) #6 x 1/4” Phillips Flat Head Screws  
B
A
C
D
E
F
TOOLS REQUIRED:  
• Phillips Screwdriver • Cutting Tool  
1-800-221-0932  
© COPYRIGHT 2001-2008 METRA ELECTRONICS CORPORATION  
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
ACURA CL 1997-1999  
A
1
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
2
Unclip the radio trim bezel and disconnect the  
clock and climate control wiring. Remove (2)  
8mm hex-head screws securing the factory  
head unit and disconnect the wiring. (Fig. A)  
3
Cut and remove all mounting clips on the Radio  
Housing EXCEPT clips "A" and "H". (Fig. B)  
Skip to step #3b on Page 10.  
B
"A"  
"A"  
"H"  
"H"  
ACURA INTEGRA 1990-1993  
1
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
A
2 Remove (3) screws from each side of the center  
console and remove the console. Remove (2)  
screws securing the factory head unit to the  
sub-dash support bracket. Slide the head  
unit/pocket assembly out and disconnect the  
wiring. (Fig. A)  
3
Cut and remove the mounting tabs from the bot-  
tom of the Rear Support Tray (Fig. A). Cut and  
remove all mounting clips on the Radio  
Housing EXCEPT clips "C" and "H" (Fig. B).  
Skip to step #3b on Page 10.  
2
B
Fig. A  
"C"  
"C"  
Fig. B  
"H"  
"H"  
1
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
ACURA INTEGRA 1994-2001  
1
2
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
A
Remove the cover cap located under the emer-  
gency brake and remove (2) screws exposed.  
Remove (2) screws from the rear corners of the  
lower dash trim bezel and remove. Remove the  
ashtray and (2) screws exposed. Unsnap the  
ashtray housing and disconnect the cigarette  
lighter harness. Remove the gear shifter knob  
and unsnap the shifter trim. Remove (2) screws  
below the radio opening and remove the upper  
dash trim bezel. Remove (2) 8mm screws secur-  
ing the factory head unit and disconnect the  
wiring. (Fig. A)  
"C"  
2
B
Fig. A  
"C"  
"H"  
3
Cut and remove all mounting clips on the Radio  
Housing EXCEPT clips "C" and "H" (Fig. A). Cut  
and remove the slots on the bottom of the ISO  
Brackets (Fig. B). (THE REAR SUPPORT TRAY  
WILL NOT BE USED). (Fig. B)  
"H"  
Fig. B  
Skip to step #3b on Page 10.  
ACURA LEGEND 1990-1996  
1
2
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
A
Remove (2) screws below the ashtray.  
Unclip the dash trim bezel. Disconnect the  
cigarette lighter wiring and remove the  
bezel. Remove (2) bolts securing the rear  
of the factory head unit and disconnect the  
wiring. (Fig. A)  
3
Attach the Mounting Bracket to the bottom of  
the Rear Support Tray (Fig. A). Cut and remove  
all mounting clips on the Radio Housing  
EXCEPT clips "E" and "J". (Fig. B)  
B
Fig. A  
Fig. B  
Skip to step #3b on Page 10.  
"E"  
"E"  
"J"  
"J"  
2
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
ACURA TL 1996-1998  
1
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
A
Using a small screwdriver, unclip the perimeter  
of the radio trim bezel. Disconnect the climate  
control and rear defroster wiring and remove  
the bezel. Remove (4) Phillips screws securing  
the factory head unit/trim bezel assembly.  
Loosen (2) Phillips screws securing the back of  
the head unit to the metal housing and slide the  
unit out. (It is NOT necessary to remove the  
screws securing the metal housing to the  
bezel). Disconnect the wiring. (Fig. A)  
2
Fig. A  
B
"B"  
Fig. B  
3
Cut and remove the mounting tabs (Fig. B) from  
the bottom of the Rear Support Tray (Fig. A).  
Cut and remove all mounting clips on the Radio  
Housing EXCEPT clips "B" and "K" (Fig. B). Cut  
and remove the slots on the bottom of the ISO  
Brackets (Fig. C).  
"B"  
"K"  
Fig. C  
"K"  
Skip to step #3b on Page 10.  
ACURA VIGOR 1992-1994  
1
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
A
2
Remove the access cap from the climate control  
cluster and (1) screw exposed. Unclip the clus-  
ter and remove (2) screws exposed. Remove the  
ashtray and (2) Phillips screws exposed.  
Remove the cover caps from each front corner of  
the center console and the screws exposed.  
Open the storage compartment, lift up the carpet  
and remove (2) screws exposed. Lift up on the  
center console and remove. Unclip the radio trim  
bezel and disconnect the wiring. Remove (2)  
bolts from the back of the factory head unit and  
disconnect the wiring. (Fig. A)  
B
"A"  
3
Cut and remove the mounting tabs from the bot-  
tom of the Rear Support Tray (Fig. A). Cut and  
remove all mounting clips on the Radio Housing  
EXCEPT clips "A" and "H" (Fig. B).  
"A"  
"H"  
Fig. B  
Skip to step #3b on Page 10.  
"H"  
3
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
HONDA ACCORD 1990-1993  
Disconnect the negative battery terminal  
to prevent an accidental short circuit.  
1
2
A
Remove (4) screws from the lower portion  
of the center console. Remove the gear  
shifter knob and lift the console out.  
Remove the ashtray and ashtray bracket.  
Remove (2) screws from the bottom of the  
head unit support, slide the unit out and  
disconnect the wiring. (Fig. A)  
Cut and remove all mounting clips on the  
Radio Housing EXCEPT clips "C" and "H"  
(Fig. A). Cut and remove the slots on the  
bottom of the ISO Brackets (Fig. B). (THE  
REAR SUPPORT TRAY WILL NOT BE  
USED).  
3
B
"C"  
Fig. A  
"C"  
"H"  
"H"  
Fig. B  
(Fig. B) Skip to step #3b on Page 10.  
HONDA ACCORD 1994-1997  
Disconnect the negative battery terminal  
to prevent an accidental short circuit.  
1
A
2
Remove the ashtray and (1) 3/4" #8 Phillips  
screw exposed. Open the storage compart-  
ment and remove (2) #8 Phillips screws  
exposed. Remove the cupholder tray and  
(3) #8 Phillips screws inside. Lift the cen-  
ter console out and remove (2) Phillips  
screws exposed at the base of the dash  
trim bezel. Unclip the bezel and remove.  
Remove (2) hex-head screws securing the  
factory head unit and disconnect the  
wiring. (Fig. A)  
B
"A"  
"A"  
Cut and remove all mounting clips on the  
Radio Housing EXCEPT clips "A" and  
"H". (Fig. B) Skip to step #3b on Page 10.  
3
"H"  
"H"  
4
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
HONDA ACCORD 1998-2002  
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
1
2
A
Unsnap the clock panel, disconnect the wiring  
and remove. Remove (1) Phillips screw exposed  
in the clock cavity. Remove (2) Phillips screws  
below the factory head unit. Unclip the radio  
trim bezel and disconnect the wiring. Remove  
(4) Phillips screws securing the factory head  
unit assembly and disconnect the wiring.  
Remove (2) screws securing the factory pocket  
to the assembly. (Fig. A)  
Fig. A  
Fig. B  
B
Cut and remove the mounting tabs from the bot-  
tom of the Rear Support Tray (Fig. A). Cut and  
remove the slots on the bottom of the ISO  
Brackets (Fig. B). Locate tabs "A" on the ISO  
Brackets for mounting, cut and remove tabs  
"B"(Fig. C). Cut and remove all mounting clips  
on the Radio Housing. (Fig. B)  
3
"A"  
Skip to step #3b on Page 10.  
Fig. C  
HONDA CIVIC 1999-2000  
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
1
2
A
Remove (2) Phillips screws from the bottom  
edge of the glove box door and remove the door.  
Remove (3) Phillips screws from the lower steer-  
ing column panel. Pull straight down on the  
lower steering column panel and remove the  
panel. Remove (2) Phillips screws under the cli-  
mate controls. Remove (4) Phillips screws from  
the lower dash location. Remove (4) Phillips  
screws securing the bottom of the dash trim  
bezel/head unit assembly and pull the assembly  
out as far as possible. Cut the zip ties securing  
the head unit and climate control wires, slide  
dash trim bezel/head unit assembly from the the  
dash cavity and disconnect the wiring. (Fig. A)  
"B"  
B
"B"  
Cut and remove all mounting clips on the Radio  
Housing EXCEPT clips "B" and "H". (Fig. B)  
Skip to step #3a on Page 9.  
3
"H"  
"H"  
5
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
HONDA CRV 1997-2001  
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
1
2
A
Open the glove box, squeeze the retaining clips  
and remove the stoppers. Lower the glove box  
and remove (2) Phillips screws from the left  
edge. Remove (2) Phillips screws from the lower  
steering column panel and remove. Unclip the  
lower console cover (below the ashtray and  
pocket) and remove. Remove (2) Phillips screws  
from the base of the center console, open the  
console pocket and remove the (4) outer screws  
exposed. Unclip the center console and remove.  
Remove (2) Phillips screws securing the radio  
trim bezel, disconnect the wiring, and remove  
the trim bezel/head unit assembly. Remove (4)  
Phillips screws securing the head unit to the  
bezel and remove. (Fig. A)  
B
"B"  
Fig. A  
"B"  
"H"  
"H"  
Cut and remove all mounting clips on the Radio  
Housing EXCEPT clips "B" and "H" (Fig. A). Cut  
and remove the slots on the bottom of the ISO  
Brackets (Fig. B). Skip to step #3a on Page 9.  
3
Fig. B  
HONDA CRV 2002-2006  
Disconnect the negative battery terminal to pre-  
vent an accidental short circuit.  
1
2
A
Remove (2) Phillips from the bottom edge of the  
radio trim bezel. Unclip the trim bezel and  
remove. Remove (4) Phillips screws securing  
the factory head unit and disconnect the wiring.  
(Fig. A)  
3
Cut and remove all mounting clips on the Radio  
Housing EXCEPT clips "C" and "H". (Fig. B)  
Skip to step #3a on Page 9.  
B
"C"  
"C"  
"H"  
"H"  
6
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
HONDA ODYSSEY 1995-1998  
ISUZU OASIS 1996-1999  
Disconnect the negative battery terminal  
to prevent an accidental short circuit.  
1
2
A
1
Lower the glove box assembly. Remove (2)  
Phillips screws exposed on the right side of  
the underdash. Remove (2) Phillips screws  
from the driver's side knee bolster and (1)  
Phillips screw in the coin pocket. Remove  
(5) Phillips screws from the underdash  
panel and remove the panel. Remove (4)  
Phillips screws from the cupholder assem-  
bly and remove. Remove (2) Phillips screws  
securing the factory head unit and discon-  
nect the wiring. (Fig. A)  
2
B
Fig. A  
"D"  
"D"  
"H"  
Fig. B  
3
Cut and remove all mounting clips on the  
Radio Housing EXCEPT clips "D" and "H"  
(Fig. A). Cut and remove the slots on the  
bottom of the ISO Brackets (Fig. B). (THE  
REAR SUPPORT TRAY WILL NOT BE  
USED). (Fig. B) Skip to step #3b on Page  
10.  
"H"  
HONDA ODYSSEY 1999-2004  
Disconnect the negative battery terminal  
to prevent an accidental short circuit.  
1
2
A
Unclip the radio trim bezel (including the  
climate control panel) and remove).  
Remove (4) Phillips screws securing the  
factory head unit and disconnect the  
wiring. (Fig. A)  
3
Cut and remove the mounting tabs from  
the bottom of the Rear Support Tray (Fig.  
A). Cut and remove the slots on the bottom  
of the ISO Brackets (Fig. B). Locate tabs  
"B" on the ISO Brackets for mounting, cut  
and remove tabs "A" (Fig. C). Cut and  
remove all mounting clips on the Radio  
Housing. (Fig. B)  
B
Fig. A  
Fig. B  
"B"  
Skip to step #3b on Page 10.  
Fig. C  
7
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 DASH DISASSEMBLY  
HONDA PRELUDE 1992-1996  
1
2
Disconnect the negative battery terminal  
to prevent an accidental short circuit.  
A
Remove (2) screws from the top of the con-  
sole trim bezel. Slide the front seats back  
and remove (4) Phillips screws from each  
side of the bezel. Pull up on the console  
trim bezel and remove. Using an angled  
screwdriver, remove (2) screws securing  
the gear shifter bracket to the bezel.  
Remove (4) screws from the radio trim  
bezel, remove the factory head unit assem-  
bly and disconnect the wiring. (Fig. A)  
2
B
Fig. B  
3
Cut and remove the mounting tabs from  
the bottom of the Rear Support Tray (Fig.  
B). Cut and remove all mounting clips on  
the Radio Housing EXCEPT clips “F” and  
"H" (Fig. B). Cut and remove the slots on  
the bottom of the ISO Brackets (Fig. C).  
Skip to step #3b on Page 10.  
"F"  
"H"  
Fig. C  
"F"  
"H"  
HONDA PRELUDE 1997-2001  
1
2
Disconnect the negative battery terminal  
to prevent an accidental short circuit.  
A
Using a panel removal tool, unclip the radio  
trim bezel and remove (some force may be  
required). Remove (4) Phillips screws  
securing the factory head unit/bracket  
housing assembly and disconnect the  
wiring. Remove (4) Phillips screws secur-  
ing the factory head unit to the bracket  
housing and remove. (Fig. A)  
"A"  
B
Cut and remove all mounting clips on the  
Radio Housing EXCEPT clips "A" and  
"G". (Fig. B) Skip to step #3a on Page 9.  
3
"A"  
"G"  
"G"  
8
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 KIT PREPARATION  
3
CRV: DOUBLE DIN HEAD UNITS: Slide the head unit into the factory bracket assembly. Align  
the holes in the brackets with the holes in the head unit and secure with the screws included with  
the unit. Cut and remove the dividing rib from the Radio Housing and snap the Housing into the  
opening (Fig. A).Skip to step #4 on Page 11.  
ISO STACK HEAD UNITS: Slide the aftermarket head unit (and digital sound processor, equaliz-  
er, etc.) into the ISO Brackets and mount the lower unit to the Brackets with the screws includ-  
ed with the unit. Slide the units into the factory bracket assembly. Align the holes in the brackets  
with the holes in the upper unit and secure with the screws included with the unit. Snap the Radio  
Housing into the radio opening (Fig. B). Skip to step #4 on Page 11.  
PRELUDE 1997-01: DOUBLE DIN HEAD UNITS: Slide the head unit into the factory bracket  
assembly. Align the holes in the brackets with the holes in the head unit and secure with the  
screws included with the unit. Cut and remove the dividing rib from the Radio Housing and snap  
the Housing into the opening (Fig. C). Skip to step #4 on Page 11. ISO STACK HEAD UNITS:  
Slide the aftermarket head unit (and digital sound processor, equalizer, etc.) into the factory  
bracket assembly. Align the holes in the brackets with the holes in the units and secure with the  
screws included with the units. Snap the Radio Housing into the radio opening (Fig. D). Skip to  
step #4 on Page 11. CIVIC 1999-00: DOUBLE DIN HEAD UNITS: Slide the head unit into the  
factory bracket assembly. Align the holes in the brackets with the holes in the head unit and  
secure with the screws included with the unit.Cut and remove the dividing rib from the Radio  
Housing and snap the Housing into the opening (Fig. E). Skip to step #4 on Page 11. ISO  
STACK HEAD UNITS: Slide the aftermarket head unit (and digital sound processor, equalizer,  
etc.) into the factory bracket assembly. Align the holes in the brackets with the holes in the units  
and secure with the screws included with the units. Snap the Radio Housing into the radio open-  
ing (Fig. F). Skip to step #4 on Page 11.  
9
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 KIT ASSEMBLY  
DOUBLE DIN RADIO PROVISION  
STACKED ISO UNITS PROVISION  
*Note: Refer also to the instructions included with the aftermarket radio.  
1
2
Disconnect the negative battery terminal to prevent an accidental short circuit.  
DOUBLE-DIN HEAD UNITS: Cut and remove the dividing rib from the radio opening. Cut and  
remove all mounting tabs on the ISO Brackets, align the holes in the Brackets with the holes  
in the head unit and secure with the screws included with the unit. Slide the Rear Support  
Tray under the unit. Position the Radio Housing over the unit and mount to the ISO Brackets  
with (4) #6 x 1/4" Flat-head Screws supplied and to the Rear Support Tray with (2) #6 x  
1/4" Flat-head Screws supplied (Fig. A). Skip to Final Assembly on page 11 for Step 4.  
ISO STACK HEAD UNITS: Cut and remove all mounting tabs on the ISO Brackets, align the  
holes in the Brackets with the holes in the head units and secure with the screws included with  
the units. Slide the Rear Support Tray under the units. Position the Radio Housing over the  
units and mount to the ISO Brackets with (4) #6 x 1/4" Flat-head Screws supplied and to the  
Rear Support Tray with (2) #6 x 1/4" Flat-head Screws supplied (Fig. B). Skip to Final  
Assembly on page 11 for Step 4.  
3
3b  
3b  
ACCORD 1994-97, CL: Secure the Mounting  
5
Bracket (mounted to the bottom of the Rear  
Support Tray) to the rear support provision in  
the sub-dash with (2) bolts previously  
removed. (Skip to Final Assembly on page 11.)  
CRV, PRELUDE 1997-01, CIVIC 1999-00:  
Snap the head unit/trim bezel assembly into  
the sub- dash. (Skip to Final Assembly on page 11.)  
ACCORD 1990-93, ODYSSEY 1995-98, PRE-  
LUDE 1992-96, INTEGRA, OASIS, VIGOR, TL:  
Snap the head unit/kit assembly into the sub-  
dash. ACCORD 1998-02, ODYSSEY 1999-02:  
Mount the head unit/kit assembly to the sub-  
dash with (4) screws previously removed in  
step #1. (Skip to Final Assembly on page 11.)  
10  
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 FINAL ASSEMBLY  
Step 4.  
FINAL ASSEMBLY  
A
B
(A) Strip wire ends back 1/2"  
B) Twist ends together  
C) Solder  
D) Tape  
C
D
Locate the factory wiring harness in the dash. Metra recommends using the  
proper mating adapter and making connections as shown. (Isolate and individ-  
ually tape off the ends of any unused wires to prevent electrical short circuit.)  
1
2
3
Re-connect the negative battery terminal and test the unit for proper operation.  
Reassemble radio and dash assemblies in reverse order of disassembly.  
FINAL WIRING CONNECTIONS  
Make wiring connections using the EIA color code chart shown below and the instructions included with the  
head unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and  
individually tape off ends of any unused wires to prevent electrical short circuit.  
Right Front (+) . . . . . . . . . . . . Gray  
METRA / EIA WIRING CODE  
Right Front (-). . . . . . . . . . . . . Gray/ Black  
12V Ignition / Acc. . . . . . . . . . Red  
Left Front (+) . . . . . . . . . . . . . White  
12V Batt / Memory. . . . . . . . . Yellow  
Left Front (-). . . . . . . . . . . . . . White / Black  
Ground. . . . . . . . . . . . . . . . . . Black*  
Right Rear (+) . . . . . . . . . . . . Violet  
Power Antenna. . . . . . . . . . . . Blue  
Right Rear (-) . . . . . . . . . . . . . Violet / Black  
Amp Turn-On . . . . . . . . . . . . . Blue / White  
Left Rear (+) . . . . . . . . . . . . . Green  
Amp Ground. . . . . . . . . . . . . . Black / White  
Left Rear (-) . . . . . . . . . . . . . . Green / Black  
Illumination . . . . . . . . . . . . . . Orange  
Dimmer . . . . . . . . . . . . . . . . . Orange / White  
*NOTE: When a Black wire is not present, ground radio to vehicle chassis.  
All colors may not be present on all leads due to manufacturer’s specifications.  
11  
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801  
NOTES  
12  
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801  
NOTES  
13  
Download from Www.Somanuals.com. All Manuals Search And Download.  
95-7801 INSTRUCTIONS  
1-800-221-0932  
REV. 04/21/08 © COPYRIGHT 2001-2008 METRA ELECTRONICS CORPORATION INST95-7801  
Download from Www.Somanuals.com. All Manuals Search And Download.  

Lenovo Computer Monitor L195 WIDE User Manual
Lenovo Laptop 3000 Y410 User Manual
Lenovo Personal Computer 0806B3U User Manual
Liebherr Beverage Dispenser WS14300 User Manual
Makita Impact Driver 6933FDWDE User Manual
Manitowoc Ice Fan 6007 User Manual
Maxim Computer Hardware DS5001FP User Manual
Maxxsonics Stereo Amplifier PZI User Manual
Metra Electronics Radio 95 7321 User Manual
METRObility Optical Systems Switch 3508 11 User Manual