INSTALLATION INSTRUCTIONS FOR PART 99-8206
APPLICATIONS
Toyota Highlander 2001-2007
4-Runner (Excluding Limited) 2003-2008
99-8206
KIT FEATURES
• DIN Head Unit Provision with Pocket
• ISO DIN Head Unit Provision with Pocket
KIT COMPONENTS
A) Radio Housing • B) ISO Brackets • C) ISO Trim Plate • D) Highlander Brackets • E) 4-Runner Brackets
B
A
E
WIRING AND ANTENNA CONNECTIONS (Sold Separately)
Harness:
C
• 70-1761 - Toyota harness 1987-up
• TYTO-01 - Toyota amp interface harness 2003-up
Antenna Adapter:
D
• Not required
TOOLS REQUIRED:
Phillips Screwdriver • Socket Wrench • Cutting Tool
1-800-221-0932
© COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
DASH DISASSEMBLY
99-8206
TOYOTA 4 RUNNER 2003-2008
(EXCLUDING LIMITED)
A
1
Disconnect the negative battery ter-
minal to prevent an accidental short
circuit.
Unsnap and remove trim from around
shifter.
2
3
Unsnap and remove trim covers from
around center console pocket edge
at front and rear of console.
B
4
5
6
Unsnap and remove center console
cover. (Figure A)
Unsnap trim ring from around ignition
key cylinder.
Remove (1) 10 mm bolt from bottom
right of panel below steering column.
Unsnap panel and pull away to gain
access behind panel. (Figure B)
C
7
8
Remove (1) 10 mm bolt on bottom
left of center panel behind panel
below steering column. (Figure B)
Remove (1) 10 mm bolt beneath cli-
mate control behind pocket door.
Unsnap and remove climate control.
(Figure C)
9
Remove (2) 10 mm bolts beneath
radio behind climate controls.
D
10
11
Unsnap and remove entire center
panel around radio. (Figure D)
Remove (2) 10 mm bolts securing
radio to remove.
1
Download from Www.Somanuals.com. All Manuals Search And Download.
DASH DISASSEMBLY
99-8206
TOYOTA HIGHLANDER 2001-2007
A
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
1
Pull and remove dash panel from
radio and climate controls. Tip: There
are 8 clips. (Figure A)
2
3
Remove (6) 10mm bolts from radio
and climate controls assembly.
(Figure B)
B
Remove assembly and disconnect
the wiring.
4
5
Remove (8) Phillips bolts and (4) Phillips
screws to separate brackets from assem-
bly. (Figure C)
C
2
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT DISASSEMBLY
99-8206
4 RUNNER BRACKET ASSEMBLY
TOYOTA HIGHLANDER BRACKET ASSEMBLY
A
Snap the appropriately marked Mounting
Brackets for your application onto the
sides of the Radio Housing. The brackets
are marked 4-Runner or Highlander and
left or right. (Figure A - 4 RUNNER)
(Figure B - HIGHLANDER)
1
B
3
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
99-8206
DIN HEAD UNIT PROVISION WITH POCKET
A
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs outward. (Figure A)
1
2
Snap the aftermarket radio into the
cage and secure. (Figure B)
B
4
Download from Www.Somanuals.com. All Manuals Search And Download.
KIT ASSEMBLY
ISO DIN HEAD UNIT PROVISION
99-8206
A
Mount the ISO Brackets to the head
unit with the screws supplied with
the radio. (Figure A)
1
Snap the radio into the radio housing
until the side clips engage. (Figure B)
2
3
Snap the ISO Trim Plate onto the
Radio/Housing assembly. (Figure B)
B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
FINAL ASSEMBLY
99-8206
FINAL ASSEMBLY
A
B
A)
B)
C)
D)
Strip wire ends back 1/2"
Twist ends together
Solder
Tape
C
D
Locate the factory wiring harness in the dash. Metra recommends using the
proper mating adapter and making connections as shown.
(Isolate and individually tape off the ends of any unused wires to prevent
electrical short circuit.)
1
Re-connect the negative battery terminal and test the unit for proper operation.
Reassemble radio and dash assemblies in reverse order of disassembly.
2
3
FINAL WIRING CONNECTIONS
Make wiring connections using the EIA color code chart shown below and the instructions included with the head
unit. Metra recommends making connections as shown below; Strip, Splice, Solder, Tape. Isolate and individually
tape off ends of any unused wires to prevent electrical short circuit.
METRA / EIA WIRING CODE
12V Ignition / Acc . . . Red
Dimmer . . . . . . . . . . Orange / White
12V Batt / Memory . . Yellow
Right Front (+) . . . . . White
Ground . . . . . . . . . . . Black*
Left Front (-). . . . . . . White / Black
Power Antenna . . . . . Blue
Right Rear (+). . . . . . Violet
Amp Turn-On . . . . . . Blue / White
Right Rear (-) . . . . . . Violet / Black
Amp Ground . . . . . . . Black / White
Left Rear (+). . . . . . . Green
Illumination. . . . . . . . Orange
*NOTE: When Black a wire is not present, ground radio to vehicle chassis.
All colors may not be present on all leads due to manufacturer’s specifications.
1-800-221-0932
REV. 07/01/09 © COPYRIGHT 2004-2009 METRA ELECTRONICS CORPORATIO INST99-8206
Download from Www.Somanuals.com. All Manuals Search And Download.
|