INSTALLATION INSTRUCTIONS FOR PART 99-8225G
APPLICATIONS
Toyota Venza
2009-2010
99-8225G
KIT FEATURES
• DIN Head Unit Provision With Pocket
• ISO DIN Head Unit Provision With Pocket
• Painted to match factory dash - G=Gray
KIT COMPONENTS
• A) Single DIN Radio Housing • B) ISO Brackets • C) Trim Plate
B
C
A
WIRING AND ANTENNA CONNECTIONS
(Sold Separately)
• 70-1761 - 1987-up Toyota harness
• TYTO-01 - 2003-up Toyota JBL amp interface
TOOLS REQUIRED:
Small Flat Blade Screwdriver/ Panel Removal Tool
• Phillips Screwdriver • Socket Set
• Magnetized Universal Swivel Head Socket Adapter
1-800-221-0932
© COPYRIGHT 2010 METRA ELECTRONICS CORPORATION
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8225G DASH DISASSEMBLY
Toyota Venza 2009-2010
A
1
Disconnect the negative battery
terminal to prevent an accidental
short circuit.
2
3
Unclip and remove the trim panel to
the right of the shifter. (Figure A)
Remove (1) Phillips screw from the
bottom of the climate control then
unclip and remove the climate
control. (Figure B)
4
5
Remove (4)10 MM bolts securing the
radio. Note: You will need a univer-
sal swivel head socket adapter to
get to the bottom left bolt.
(Figure C)
B
Remove (4) Phillips screws securing
the factory radio to the a/c vent
panel. (Figure D)
Continue to kit assembly.
D
C
REAR VIEW - RADIO AND A/C VENT PANEL
RADIO
1
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8225G KIT ASSEMBLY
DIN HEAD UNIT PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
1
2
Secure the Radio Housing into the
factory a/c vent panel using the
factory hardware. (Figure A)
A
REAR VIEW - A/C VENT PANEL
Locate the factory wiring harness in
the dash. Metra recommends using
the proper mating adapter from Metra
or AXXESS. Re-connect the negative
battery terminal and test the unit for
proper operation.
3
Slide the DIN cage into the Radio
Housing and secure by bending the
metal locking tabs down. (Figure B)
B
4
5
6
Slide the aftermarket head unit into
the cage and secure. (Figure C)
Snap the factory vent panel/Radio
Housing over dash cavity. (Figure D)
Reassemble remaining radio and
dash assemblies in reverse order of
disassembly.
D
C
2
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8225G KIT ASSEMBLY
ISO DIN HEAD UNIT PROVISION WITH POCKET
*Note: Refer also to the instructions included with the aftermarket radio.
Secure the Radio Housing into the
1
2
3
A
factory a/c vent panel using the
factory hardware. (Figure A)
REAR VIEW - A/C VENT PANEL
Mount the ISO Brackets to the head
unit with the screws supplied with
the unit. (Figure B)
Slide the head unit into the radio
opening until the side clips engage.
(Figure C)
4
5
6
Snap the Trim Plate into the Radio
Housing. (Figure C)
Snap the factory vent panel/Radio
Housing over dash cavity. (Figure D)
B
Reassemble remaining radio and
dash assemblies in reverse order of
disassembly.
D
C
3
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8225G
NOTES
4
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8225G
NOTES
5
Download from Www.Somanuals.com. All Manuals Search And Download.
99-8225G INSTRUCTIONS
1-800-221-0932
REV. 05/20/10 © COPYRIGHT 2010 METRA ELECTRONICS CORPORATION INST99-8225G
Download from Www.Somanuals.com. All Manuals Search And Download.
|